mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
54e5e396c5
83 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Mikhail Zhilkin
|
2d6784a033 |
ramips: add support for Sercomm S1500 devices
This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> |
||
Wenli Looi
|
32ea8a9a7e |
ramips: add support for Netgear EAX12 series
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6) extenders that share the SoC, WiFi chip, and image format with the WAX202. Specifications: * MT7621, 256 MiB RAM, 128 MiB NAND * MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC) * Ethernet: 1 port 10/100/1000 * UART: 115200 baud (labeled on board) All LEDs and buttons appear to work without state_default. Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. References in GPL source: https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz * target/linux/ramips/dts/mt7621-rfb-ax-nand.dts DTS file for this device. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
Alexey Bartenev
|
ce998cb6e1 |
ramips: add support for D-Link DIR-806A B1 router
General specification: SoC Type: MediaTek MT7620A (580MHz) ROM: 8 MB SPI-NOR (MX25L6406E) RAM: 64 MB DDR (W9751G6KB-25) Switch: MediaTek MT7530 Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) Wireless: 2.4 GHz (MediaTek RT5390): b/g/n Wireless: 5 GHz (MediaTek MT7610EN): ac/n Buttons: 2 button (POWER, WPS/RESET) Bootloader: U-Boot 1.1.3 Power: 12 VDC, 0.5 A MACs: | LAN | [Factory + 0x04] - 2 | | WLAN 2.4g | [Factory + 0x04] - 1 | | WLAN 5g | [Factory + 0x8004] - 3 | | WAN | [Factory + 0x04] - 2 | OEM easy installation: 1. Use a PC to browse to http://192.168.0.1. 2. Go to the System section and open the Firmware Update section. 3. Under the Local Update at the right, click on the CHOOSE FILE... 4. When a modal window appears, choose the firmware file and click on the Open. 5. Next click on the UPDATE FIRMWARE button and upload the firmware image. Wait for the router to flash and reboot. OEM installation using the TFTP method (need level converter): 1. Download the latest firmware image. 2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware image to the root directory of the server. 3. Power off the router and use a twisted pair cable to connect the PC to any of the router's LAN ports. 4. Configure the network adapter of the PC to use IP address 192.168.0.180 and subnet mask 255.255.255.0. 5. Connect serial port (57600 8N1) and turn on the router. 6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load system code then write to Flash via TFTP."). 7. Press Y key when show "Warning!! Erase Linux in Flash then burn new one. Are you sure? (Y/N)" Input device IP (192.168.0.1) ==:192.168.0.1 Input server IP (192.168.0.180) ==:192.168.0.180 Input Linux Kernel filename () ==:firmware_name The router should download the firmware via TFTP and complete flashing in a few minutes. After flashing is complete, use the PC to browse to http://192.168.1.1 or ssh to proceed with the configuration. Signed-off-by: Alexey Bartenev <41exey@proton.me> |
||
Maximilian Weinmann
|
8fcfb21b16 |
ramips: Add support for Beeline SmartBox TURBO+
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.
Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A
Installation (fw 2.0.9)
-----------------------
1. Login to the web interface under SuperUser (root) credentials.
Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
device written on the backplate stick.
2. Navigate to Setting -> WAN. Add:
Name - WAN1
Connection Type - Static
IP Address - 172.16.0.1
Netmask - 255.255.255.0
Save -> Apply. Set default: WAN1
3. Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
Protocol - SSH
Port - 22
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN Interface - WAN1
Save ->Apply
Add:
Protocol - HTTP
Port - 80
IP Address - 172.16.0.1
Netmask - 255.255.255.0
WAN interface - WAN1
Save -> Apply
4. Set up your PC ethernet:
Connection Type - Static
IP Address - 172.16.0.2
Netmask - 255.255.255.0
Gateway - 172.16.0.1
5. Connect PC using ethernet cable to the WAN port of the router
6. Connect to the router using SSH shell under SuperUser account
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 171.16.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:e8 |
| WAN | label + 1 | *:e9 |
| 2g | label + 4 | *:ec |
| 5g | label + 5 | *:ed |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset | Size | Description |
+---+-------------------+-------------+--------------------+
| 1 | 0x0 | 0x200 | Tag Header Factory |
| 2 | 0x200 | 0x100 | Tag Header Kernel1 |
| 3 | 0x300 | 0x100 | Tag Header Kernel2 |
| 4 | 0x400 | SIZE_KERNEL | Kernel |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI) |
+---+-------------------+-------------+--------------------+
Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
|
||
Christoph Krapp
|
e882af2850 |
ramips: add support for Linksys RE7000
Hardware specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 16 MB (Macronix MX25L12835FM2I-10G) - RAM: 128 MB (Nanya NT5CC64M16GP-DI) - WLAN 2.4 GHz: 2x2 MediaTek MT7603EN - WLAN 5 GHz: 2x2 MediaTek MT7615N - Ethernet: 1x 10/100/1000 Mbps - LED: Power, Wifi, WPS - Button: Reset, WPS - UART: 1:VCC, 2:GND, 3:TX, 4:RX (from LAN port) Serial console @ 57600,8n1 Flash instructions: Connect to serial console and start up the device. As the bootloader got locked you need to type in a password to unlock U-Boot access. When you see the following output on the console: relocate_code Pointer at: 87f1c000 type in the super secure password: 1234567890 Then select TFTP boot from RAM by selecting option 1 in the boot menu. As Linksys decided to leave out a basic TFTP configuration you need to set server- & client ip as well as the image filename the device will search for. You need to use the initramfs openwrt image for the TFTP boot process. Once openwrt has booted up, upload the sysupgrade image via scp and run sysupgrade as normal. Signed-off-by: Christoph Krapp <achterin@gmail.com> |
||
|
Maximilian Weinmann
|
ecdb24814f |
ramips: add support for SNR-CPE-ME1
SNR-CPE-ME1 is a wireless WiFi 5 router manufactured by SNR/NAG company.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : SPI-NOR 16 MiB (GD25Q128CSIG)
- WLAN : 2.4 GHz (MediaTek MT7603EN)
5 GHz (MediaTek MT7610EN)
- Ethernet : 10/100/1000 Mbps x5
- Switch : MediaTek MT7530 (in SoC)
- USB : 3.0 x1
- UART : through-hole on PCB
- [J4] 3.3V, RX, TX, GND (57600n8)
- Power : 12 VDC, 2 A
Flash instruction via TFTP:
1. Boot SNR-CPE-ME1 to recovery mode
(hold the reset button while power on)
2. Send firmware via TFTP client:
TFTP Server address: 192.168.1.1
TFTP Client address: 192.168.1.131
3. Wait ~120 seconds to complete flashing
4. Do sysupgrade using web-interface
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
|
||
Andreas Böhler
|
28df7f7ff2 |
ramips: mt7621: add support for ZyXEL WSM20
The ZyXEL WSM20 aka Multy M1 is a cheap mesh router system by ZyXEL based on the MT7621 CPU. Specifications ============== SoC: MediaTek MT7621AT (880MHz) RAM: 256MiB Flash: 128MiB NAND Wireless: 802.11ax (2x2 MT7915E DBDC) Ethernet: 4x 10/100/1000 (MT7530) Button: 1x WPS, 1x Reset, 1x LED On/Off LED: 7 LEDs (3x white, 2x red, 2x green) MAC address assignment ====================== The MAC address assignment follows stock: The label MAC address is the LAN MAC address, the WAN address is read from flash. The WiFi MAC addresses are set in userspace to label MAC + 1 and label MAC + 2. Installation (web interface) ============================ The device is cloud-managed, but there is a hidden local firmware upgrade page in the OEM web interface. The device has to be registered in the cloud in order to be able to access this page. The system has a dual firmware design, there is no way to tell which firmware is currently booted. Therefore, an -initramfs version is flashed first. 1. Log into the OEM web GUI 2. Access the hidden upgrade page by navigating to https://192.168.212.1/gui/#/main/debug/firmwareupgrade 3. Upload the -initramfs-kernel.bin file and flash it 4. Wait for OpenWrt to boot and log in via SSH 5. Transfer the sysupgrade file via SCP 6. Run sysupgrade to install the image 7. Reboot and enjoy NB: If the initramfs version was installed in RAS2, the sysupgrade script sets the boot number to the first partition. A backup has to be performed manually in case the OEM firwmare should be kept. Installation (UART method) ========================== The UART method is more difficult, as the boot loader does not have a timeout set. A semi-working stock firmware is required to configure it: 1. Attach UART 2. Boot the stock firmware until the message about failsafe mode appears 3. Enter failsafe mode by pressing "f" and "Enter" 4. Type "mount_root" 5. Run "fw_setenv bootmenu_delay 3" 6. Reboot, U-Boot now presents a menu 7. The -initramfs-kernel.bin image can be flashed using the menu 8. Run the regular sysupgrade for a permanent installation Changing the partition to boot is a bit cumbersome in U-Boot, as there is no menu to select it. It can only be checked using mstc_bootnum. To change it, issue the following commands in U-Boot: nand read 1800000 53c0000 800 mw.b 1800004 1 1 nand erase 53c0000 800 nand write 1800000 53c0000 800 This selects FW1. Replace "mw.b 1800004 1 1" by "mw.b 1800004 2 1" to change to the second slot. Back to stock ============= It is possible to flash back to stock, but a OEM firmware upgrade is required. ZyXEL does not provide the link on its website, but the link can be acquired from the OEM web GUI by analyzing the transferred JSON objects. It is then a matter of writing the firmware to Kernel2 and setting the boot partition to FW2: mtd write zyxel.bin Kernel2 echo -ne "\x02" | dd of=/dev/mtdblock7 count=1 bs=1 seek=4 conv=notrunc Signed-off-by: Andreas Böhler <dev@aboehler.at> Credits to forum users Annick and SirLouen for their initial work on this device |
||
|
Alexey Bartenev
|
dc79b51533 |
ramips: add support for Keenetic Lite III rev. A
General specification: SoC Type: MediaTek MT7620N (580MHz) ROM: 8 MB SPI-NOR (W25Q64FV) RAM: 64 MB DDR (EM6AB160TSD-5G) Switch: MediaTek MT7530 Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) Wireless: 2.4 GHz (MediaTek RT5390): b/g/n Buttons: 3 button (POWER, RESET, WPS) Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT) Bootloader: U-Boot 1.1.3 Power: 9 VDC, 0.6 A MAC in stock: |- + | | LAN | RF-EEPROM + 0x04 | | WLAN | RF-EEPROM + 0x04 | | WAN | RF-EEPROM + 0x28 | OEM easy installation 1. Use a PC to browse to http://my.keenetic.net. 2. Go to the System section and open the Files tab. 3. Under the Files tab, there will be a list of system files. Click on the Firmware file. 4. When a modal window appears, click on the Choose File button and upload the firmware image. 5. Wait for the router to flash and reboot. OEM installation using the TFTP method 1. Download the latest firmware image and rename it to klite3_recovery.bin. 2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware image to the root directory of the server. 3. Power off the router and use a twisted pair cable to connect the PC to any of the router's LAN ports. 4. Configure the network adapter of the PC to use IP address 192.168.1.2 and subnet mask 255.255.255.0. 5. Power up the router while holding the reset button pressed. 6. Wait approximately for 5 seconds and then release the reset button. 7. The router should download the firmware via TFTP and complete flashing in a few minutes. After flashing is complete, use the PC to browse to http://192.168.1.1 or ssh to proceed with the configuration. Signed-off-by: Alexey Bartenev <41exey@proton.me> |
||
Aleksey Nasibulin
|
d45659a571 |
ramips: add support for SNR-CPE-ME2-SFP
SNR-CPE-ME2-SFP is a wireless router with SFP cage manufactured by SNR/NAG company. Specification: - SoC: MediaTek MT7621A - CPU: 880MHz - Flash: 16 MB (GD25Q127CSIG) - RAM: 256 MB - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7615DN) - Ethernet: 4x 10/100/1000 Mbps - SFP cage (using RTL8211FS-CG) - USB 3.0 port - Power: 12 VDC, 2 A Flash instruction via TFTP: 1. Boot SNR-CPE-ME2 to recovery mode (press reset button and power on device, hold button for ~10 seconds) 2. Send firmware via TFTP client: TFTP Server address: 192.168.1.1 TFTP Client address: 192.168.1.131 3. Wait ~120 seconds to complete flashing 4. Do sysupgrade using web-interface MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 6A:C4:DD:xx:xx:28 | | Ethernet | + 1 | 6A:C4:DD:xx:xx:29 | | 2g | + 2 | 6A:C4:DD:xx:xx:2A | | 5g | + 3 | 6A:C4:DD:xx:xx:2B | +----------+------------------+-------------------+ Notes: - Reading sfp eeprom is not supported [1] (driver issue). Stock image has the same situation. References: 1. https://forum.openwrt.org/t/mt7621-and-reading-sfp-eeprom/152249 Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru> |
||
Michael Pratt
|
4ef86c620f |
ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600
Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)
this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.
**Specification:**
- MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2
- RT5592N WLAN PCI chip, 5 GHz, 2x2
- QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM NT5TU32M16
- UART console J2, populated
- USB 2.0 port direct to SOC
- 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line
- 3 buttons reset, wps, "reg" (registeration)
- 4 antennas internal omni-directional plates
NOT YET SUPPORTED: VoIP
- Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data
- Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins)
**MAC addresses:**
MAC address labeled as MAC ADDRESS
MACs present in both wifi cal data and uboot environment
eth0.1/phy1 ---- *:82 rf 0x4
phy0 ---- *:83 factory 0x4
eth0.2 MAC *:b8 "wanaddr"
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.0.1
username and password 'admin'
Navigate to gear icon, "Device Management", "Tools"
select the factory.dlf image
Upload and verify checksum
Method 2: Serial to upload initramfs:
Follow directions for TFTP recovery
upload and boot initramfs and do a sysupgrade
**TFTP recovery:**
Requires UART serial console, reset button does nothing
rename initramfs-kernel.bin to 'uImageEPG600'
make available on TFTP server at 192.168.99.8
power board, interrupt boot with "4"
execute `tftpboot` and `bootm` (with the load address)
**Return to OEM:**
Images from OEM are provided, but not compatible
with openwrt sysupgrade. So it must be modified.
Alternatively, back up all mtd partitions before flashing
**Note on switch registers:**
The necessary registers needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by using the following lines in the switch driver ar8327.c
in the function 'ar8327_hw_config_of'
where 'qca,ar8327-initvals' is parsed from DTS
before the new register values are written:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
||
Karl Chan
|
92276eef70 |
ramips: add support for ASUS RT-AX54
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
1x LAN (blue, configurable)
1x WAN (blue, configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Karl Chan <exkc@exkc.moe>
|
||
Harm Berntsen
|
09f313bfd7 |
ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access point distributed as Experia WiFi by KPN in the Netherlands. It features two ethernet ports and 2 internal antennas. Specifications -------------- SOC : Mediatek MT7621AT ETH : Two 1 gigabit ports, built into the SOC WIFI : MT7615DN BUTTON: Reset BUTTON: WPS LED : Power (green+red) LED : WiFi (green+blue) LED : WPS (green+red) LED : Followme (green+red) Power : 12 VDC, 1A barrel plug Winbond variant: RAM : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM Flash : Winbond W25Q256JVFQ, 256Mb SPI U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1 Macronix variant: RAM : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM Flash : MX25l25635FMI-10G, 256Mb SPI U-Boot: 1.1.3 (Dec 4 2017 - 11:37:57), Ralink 5.0.0.1 Serial ------ The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin header. The pinout is: VCC (the square), RX, TX, GND. Installation ------------ See the Wiki page [1] for more details, it comes down to: 1. Open the device, take off the heat sink 2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also connect the RESET pin for stability (thanks @FPSUsername for reporting) 3. Make a backup in case you want to revert to stock later 4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash 5. Ensure the bootpartition variable is set to 0 in the U-Boot environment located at 0x30000 Note that the U-Boot is password protected, this can optionally be removed. See the forum [2] for more details. MAC Addresses(stock) -------------------- +----------+------------------+-------------------+ | use | address | example | +----------+------------------+-------------------+ | Device | label | 00:00:00:11:00:00 | | Ethernet | + 3 | 00:00:00:11:00:03 | | 2g | + 0x020000f00001 | 02:00:00:01:00:01 | | 5g | + 1 | 00:00:00:11:00:01 | +----------+------------------+-------------------+ The label address is stored in ASCII in the board_data partition Notes ----- - This device has a dual-boot partition scheme, but OpenWRT will claim both partitions for more storage space. Known issues ------------ - 2g MAC address does not match stock due to missing support for that in macaddr_add - Only the power LED is configured by default References ---------- [1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99 [2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653 Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Harm Berntsen <git@harmberntsen.nl> |
||
|
Mikhail Zhilkin
|
1a35edfbdb |
ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).
Serial console (UART)
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
| J2
|
+--- Don't connect
Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
pressing 't'
3. Load and run OpenWrt initramfs image:
tftpboot
bootm
4. Once inside OpenWrt, switch to the first boot image:
fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv BootImage 1
reboot
Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
the OEM firmware
MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
| | MAC example 1 | MAC example 2 | Algorithm |
+---------+-------------------+-------------------+-------------+
| label | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| LAN | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WAN | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2 |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).
Notes
-----
[1] WAN MAC address:
a. First octet of WAN MAC is differ than others and OUI is not related
to TP-Link company. This probably should be fixed.
b. Flipping bits in first octet and hex delta are different for the
different MAC examples:
+-----------------+----------------+----------------+
| | Example 1 | Example 2 |
+-----------------+----------------+----------------+
| LAN | 68 = 0110 1000 | 50 = 0101 0000 |
| MAC (1st octet) | ^ ^ ^ | |
+-----------------+----------------+----------------+
| WAN | 72 = 0111 0010 | 54 = 0101 0100 |
| MAC (1st octet) | ^ ^ ^ | ^ |
+-----------------+----------------+----------------+
| HEX delta | 0xa | 0x4 |
+-----------------+----------------+----------------+
| DEC delta | 4 | 4 |
+-----------------+----------------+----------------+
c. DEC delta is a constant (4). This looks like a mistake in OEM
firmware and probably should be fixed.
Based on the above, I decided to keep correct OUI and make WAN MAC =
label + 1.
[2] Bootloaders
The device contains 3 bootloaders:
- First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
located on NAND Flash to load next full-feature Uboot.
- Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
bootloader includes recovery webserver. Requires special uImages to
continue the boot process:
0x00 (os0, os1) - firmware uImage
0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
- Additionally, both slots of the original TP-Link firmware contains
Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
magics and CRCs. We don't use this U-Boot with OpenWrt.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Felix Baumann
|
75451681d0
|
uboot-envtools: add support for ramips Asus RX-AX53U
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition can be correctly read. Signed-off-by: Felix Baumann <felix.bau@gmx.de> [ improve commit title and description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> |
||
|
Alexey Bartenev
|
3f201d1f8e |
ramips: add support for SNR-CPE-W4N-MT router
General specification: - SoC Type: MediaTek MT7620N (580MHz) - ROM: 8 MB SPI-NOR (W25Q64FV) - RAM: 64 MB DDR (M13S5121632A) - Switch: MediaTek MT7530 - Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4) - Wireless 2.4 GHz: b/g/n - Buttons: 1 button (RESET) - Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5 - Power: 12 VDC, 1.0 A Flash by the native uploader in 2 stages: 1. Use the native uploader to flash an initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by "Administration/Management/Firmware update/Choose File" in vendor's web interface (ip: 192.168.1.10, login: Admin, password: Admin). Wait ~160 seconds. 2. Flash a sysupgrade image via the initramfs image. Choose openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin file by "System/Backup/Flash Firmware/Flash image..." in LuCI web interface (ip: 192.168.1.1, login: root, no password). Wait ~240 seconds. Flash by U-Boot TFTP method: 1. Configure your PC with IP 192.168.1.131 2. Set up TFTP server and put the openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin image on your PC 3. Connect serial port (57600 8N1) and turn on the router. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load system code then write to Flash via TFTP."). Press Y key when show "Warning!! Erase Linux in Flash then burn new one. Are you sure? (Y/N)" Input device IP (192.168.1.1) ==:192.168.1.1 Input server IP (192.168.1.131) ==:192.168.1.131 Input Linux Kernel filename () ==: openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin 3. Wait ~120 seconds to complete flashing Signed-off-by: Alexey Bartenev <41exey@proton.me> |
||
|
Mikhail Zhilkin
|
0ec8d991c2 |
ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface under admin account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following line:
<PARAMETER name="Password" type="string" value="<your router serial \
is here>" writable="1" encryption="1" password="1"/>
5. Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
ETxxxxxxxxxx is the serial number from the backplate label)
9. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | *:50 |
| WAN | label + 11 | *:5b |
| 2g | label + 2 | *:52 |
| 5g | label + 3 | *:53 |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
|
Mikhail Zhilkin
|
0cfd15552e |
ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Status (RGB)
- 1x 2.4G (blue, hardware, mt76-phy0)
- 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
firmware
6. Update firmware using web interface with the OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
MAC Addresses
-------------
+-----+------------+------------+
| use | address | example |
+-----+------------+------------+
| LAN | label | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g | label + 2 | *:74, *:d4 |
| 5g | label + 3 | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Shiji Yang
|
f7f9203854 |
ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based on Tenbay WR1800K. They have the same hardware circuits and u-boot. SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile), SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these models run the same firmware. Specifications: SOC: MT7621 + MT7905 + MT7975 ROM: 128 MiB RAM: 256 MiB LED: status *3 R/G/B Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP Server: 192.168.1.254 TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken) MAC Address: use address source label 30:xx:xx:xx:xx:62 wan lan 30:xx:xx:xx:xx:65 factory.0x8004 wan 30:xx:xx:xx:xx:62 factory.0x8004 -3 wlan2g 30:xx:xx:xx:xx:64 factory.0x0004 wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit TFTP Installation (initramfs image only & recommend): 1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0 2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root directory of the tftp server. (tftpd64 is a good choice for Windows) 3. Start the TFTP server, plug in the power supply, and wait for the system to boot. 4. Backup "firmware" partition and rename it to "firmware.bin", we need it to back to stock firmware. 5. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 6. Apply sysupgrade.bin in OpenWrt LuCI. Web UI Installation: 1. Apply update by uploading initramfs-factory.bin to the web UI. 2. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI. Recovery to stock firmware: a. Upload "firmware.bin" to OpenWrt /tmp, then execute: /# mtd -r write /tmp/firmware.bin firmware b. We can also write factory image "UploadBrush-bin.img" to firmware partition to recovery. Upload image file to /tmp, then execute: /# mtd erase firmware /# mtd -r write /tmp/UploadBrush-bin.img firmware How to extract stock firmware image: Download stock firmware, then use openssl: openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \ -out "firmware.tar.tgz" -k QiLunSmartWL Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com> |
||
Rosen Penev
|
f4eef5f2a1 |
ramips: add support for Linksys E7350
Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com> |
||
|
Rosen Penev
|
26a6a6a60b |
ramips: add support for Belkin RT1800
Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com> |
||
Andrey Butirsky
|
5806914794 |
ramips: add support for Kroks Rt-Cse SIM Injector DS
Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958: https://kroks.ru/search/?text=1958 See Kroks OpenWrt fork for support of other models: https://github.com/kroks-free/openwrt Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 5x 10/100 Mbps - 2.4 GHz: b/g/n SoC - USB: 1x - SIM-reader: 2x (driven by a dedicated chip with it's own firmware) - Buttons: reset - LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.) Flashing: - sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254 - U-Boot launches a WEB server if Reset button is held during power up, IP: 192.168.1.1 MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Andrey Butirsky <butirsky@gmail.com> |
||
|
Andrey Butirsky
|
0a79c77a4e |
ramips: add support for Kroks Rt-Pot mXw DS RSIM router
Aka "Kroks KNdRt31R19". Ported from v19.07.8 of OpenWrt fork: see https://github.com/kroks-free/openwrt for support of other models. Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - mPCIe: 1x (usually equipped with an LTE modem by vendor) - Buttons: reset - LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status Flashing: - sysupgrade image via stock firmware WEB interface. - U-Boot launches a WEB server if Reset button is held during power up. Server IP: 192.168.1.1 SIM card switching: The device supports up to 4 SIM cards - 2 locally on board and 2 on remote SIM-injector. By default, 1-st local SIM is active. To switch to e.g. 1-st remote SIM: echo 0 > /sys/class/gpio/modem1power/value echo 0 > /sys/class/gpio/modem1sim1/value echo 1 > /sys/class/gpio/modem1rsim1/value echo 1 > /sys/class/gpio/modem1power/value MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Kroks <dev@kroks.ru> [butirsky@gmail.com: port to master; drop dts-v1] Signed-off-by: Andrey Butirsky <butirsky@gmail.com> |
||
|
Mikhail Zhilkin
|
85b41cbd3b |
ramips: add support for Beeline SmartBox TURBO
Beeline SmartBox TURBO is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 2 buttons (Reset & WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (admin:admin)
2. Navigate to Settings -> WAN -> Add static IP interface (e.g.
10.0.0.1/255.255.255.0)
3. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
10.0.0.0/255.255.255.0 and interface created before
4. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
ethernet cable to the WAN port of the router
5. Connect to the router using SSH shell (SuperUser:SNxxxxxxxxxx, where
SNxxxxxxxxxx is the serial number from the backplate label)
6. Run in SSH shell:
sh
7. Make a mtd backup (optional, see related section)
8. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
9. Login to the router web interface (admin:admin)
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
1. Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 10.0.0.2
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:54 |
| WAN | label + 1 | *:55 |
| 2g | label + 4 | *:58 |
| 5g | label + 5 | *:59 |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Co-developed-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
André Valentin
|
2cc5059240 |
ramips: add support for ZyXEL LTE3301-Plus
The ZyXEL LTE3301-PLUS is an 4G indoor CPE with 2 external LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7615E
- Switch: 4 LAN ports (Gigabit)
- LTE: Quectel EG506 connected by USB3 to SoC
- SIM: 1 micro-SIM slot
- USB: USB3 port
- Buttons: Reset, WPS
- LEDs: Multicolour power, internet, LTE, signal, Wifi, USB
- Power: 12V, 1.5A
The device is built as an indoor ethernet to LTE bridge or router with
Wifi.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
MAC assignment:
lan: 98:0d:67:ee:85:54 (base, on the device back)
wlan: 98:0d:67:ee:85:55
Installation from web GUI:
- Log in as "admin" on http://192.168.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- format ubi device: ubiformat /dev/mtd6
- attach ubi device: ubiattach -m6
- create rootfs volume: ubimkvol /dev/ubi0 -n0 -N rootfs -s 1MiB
- rootfs_data volume: ubimkvol /dev/ubi0 -n1 -N rootfs_data -s 1MiB
- run sysupgrade with sysupgrade image
For more details about flashing see
commit
|
||
|
Wenli Looi
|
4cccea02a6 |
ramips: fix fw_setsys
This change was included in the original pull request but later omitted for some reason: https://github.com/openwrt/openwrt/pull/4936 Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
|
Wenli Looi
|
0bfe1cfbb1 |
ramips: support fw_printenv for Netgear WAX202
Config partition contains uboot env for the first 0x20000 bytes. The rest of the partition contains other data including the device MAC address and the password printed on the label. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> |
||
|
Shiji Yang
|
1330816178 |
ramips: add support for H3C TX1800 Plus / TX1801 Plus / TX1806
H3C TX180x series WiFi6 routers are customized by different carrier.
While these three devices look different, they use the same motherboard
inside. Another minor difference comes from the model name definition
in the u-boot environment variable.
Specifications:
SOC: MT7621 + MT7915
ROM: 128 MiB
RAM: 256 MiB
LED: status *2
Button: reset *1 + wps/mesh *1
Ethernet: lan *3 + wan *1 (10/100/1000Mbps)
TTL Baudrate: 115200
TFTP server IP: 192.168.124.99
MAC Address:
use address(sample 1) address(sample 2) source
label 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 u-boot-env@ethaddr
lan 88:xx:xx:98:xx:13 88:xx:xx:a2:xx:a6 $label +1
wan 88:xx:xx:98:xx:12 88:xx:xx:a2:xx:a5 $label
WiFi4_2G 8a:xx:xx:58:xx:14 8a:xx:xx:52:xx:a7 (Compatibility mode)
WiFi5_5G 8a:xx:xx:b8:xx:14 8a:xx:xx:b2:xx:a7 (Compatibility mode)
WiFi6_2G 8a:xx:xx:18:xx:14 8a:xx:xx:12:xx:a7
WiFi6_5G 8a:xx:xx:78:xx:14 8a:xx:xx:72:xx:a7
Compatibility mode is used to guarantee the connection of old devices
that only support WiFi4 or WiFi5.
TFTP + TTL Installation:
Although a TTL connection is required for installation, we do not need
to tear down it. We can find the TTL port from the cooling hole at the
bottom. It is located below LAN3 and the pins are defined as follows:
|LAN1|LAN2|LAN3|----|WAN|
--------------------
|GND|TX|RX|VCC|
1. Set tftp server IP to 192.168.124.99 and put initramfs firmware in
server's root directory, rename it to a simple name "initramfs.bin".
2. Plug in the power supply and wait for power on, connect the TTL cable
and open a TTL session, enter "reboot", then enter "Y" to confirm.
Finally push "0" to interruput boot while booting.
3. Execute command to install a initramfs system:
# tftp 0x80010000 192.168.124.99:initramfs.bin
# bootm 0x80010000
4. Backup nand flash by OpenWrt LuCI or dd instruction. We need those
partitions if we want to back to stock firmwre due to official
website does not provide download link.
# dd if=/dev/mtd1 of=/tmp/u-boot-env.bin
# dd if=/dev/mtd4 of=/tmp/firmware.bin
5. Edit u-boot env to ensure use default bootargs and first image slot:
# fw_setenv bootargs
# fw_setenv bootflag 0
6. Upgrade sysupgrade firmware.
7. About restore stock firmware: flash the "firmware" and "u-boot-env"
partitions that we backed up in step 4.
# mtd write /tmp/u-boot-env.bin u-boot-env
# mtd write /tmp/firmware.bin firmware
Additional Info:
The H3C stock firmware has a 160-byte firmware header that appears to
use a non-standard CRC32 verification algorithm. For this part of the
data, the u-boot does not check it so we can just directly replace it
with a placeholder.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
|
||
Oleg S
|
6c7e337c80
|
ramips: Add support command fw_setsys for Xiaomi routers
The system parameters are contained in the Bdata partition. To use the fw_setsys command, you need to create a file fw_sys.config. This file is created after calling the functions ubootenv_add_uci_sys_config and ubootenv_add_app_config. Signed-off-by: Oleg S <remittor@gmail.com> [ wrapped commit description to 72 char ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> |
||
|
Mikhail Zhilkin
|
bd783fd60a |
ramips: add support for Beeline SmartBox GIGA
Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by
Sercomm company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Nanya NT5CC128M16JR-EK
Flash: 128 MiB, Macronix MX30LF1G18AC
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7613BE): a/n/ac, 2x2
Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2)
USB ports: 1xUSB3.0
Button: 1 button (Reset/WPS)
PCB ID: DBE00B-1.6MM
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Downgrade stock (Beeline) firmware to v.1.0.02;
2. Give factory OpenWrt image a shorter name, e.g. 1001.img;
3. Upload and update the firmware via the original web interface.
Remark: You might need make the 3rd step twice if your running firmware
is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware
reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.
Revert to stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
2. Optional: Update with any stock (Beeline) firmware if you want to
overwrite OpenWrt in Slot 0 completely.
MAC Addresses
-------------
+-----+-----------+---------+
| use | address | example |
+-----+-----------+---------+
| LAN | label | *:16 |
| WAN | label + 1 | *:17 |
| 2g | label + 4 | *:1a |
| 5g | label + 5 | *:1b |
+-----+-----------+---------+
The label MAC address was found in Factory 0x21000
Notes
-----
1. The following scripts are required for the build:
sercomm-crypto.py - already exists in OpenWrt
sercomm-partition-tag.py - already exists in OpenWrt
sercomm-payload.py - already exists in OpenWrt
sercomm-pid.py - new, the part of this pull request
sercomm-kernel-header.py - new, the part of this pull request
2. This device (same as other Sercomm S2,S3-based devices) requires
special LZMA and LOADADDR settings for successful boot:
LZMA_TEXT_START=0x82800000
KERNEL_LOADADDR=0x81001000
LOADADDR=0x80001000
3. This device (same as several other Sercomm-based devices - Beeline,
Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing
real partition offsets, which may differ from device to device
depending on the number and location of bad blocks on NAND.
"fixed-partitions" is used if the partition map is not found or
corrupted. This behavour (it's the same as on stock firmware) is
provided by MTD_SERCOMM_PARTS module.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
|
Mikhail Zhilkin
|
498c15376b |
ramips: add support for MTS WG430223
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Clemens Hopfer
|
4891b86538 |
ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure: YunCore AX820: indoor ceiling mount AP with integrated antennas YunCore HWAP-AX820: outdoor enclosure with external (N) connectors Hardware specs: SoC: MediaTek MT7621DAT Flash: 16 MiB SPI NOR RAM: 128MiB (DDR3, integrated) WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN) LED: Status (green) Button: Reset Power: 802.11af/at PoE; DC 12V,1A Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external Flash instructions: The "OpenWRT support" version of the AX820 comes with a LEDE-based firmware with proprietary MTK drivers and a luci webinterface and ssh accessible under 192.168.1.1 on LAN; user root, no password. The sysupgrade.bin can be flashed using luci or sysupgrade via ssh, you will have to force the upgrade due to a different factory name. Remember: Do *not* preserve factory configuration! MAC addresses as used by OEM firmware: use address source 2g 44:D1:FA:*:0b Factory 0x0004 (label) 5g 46:D1:FA:*:0b LAA of 2g lan 44:D1:FA:*:0c Factory 0xe000 wan 44:D1:FA:*:0d Factory 0xe000 + 1 The wan MAC can also be found in 0xe006 but is not used by OEM dtb. Due to different MAC handling in mt76 the LAA derived from lan is used for 2g to prevent duplicate MACs when creating multiple interfaces. Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> |
||
Abdul Aziz Amar
|
78c3534645 |
ramips: add support for BOLT! Arion
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.
Specifications:
- SoC: MediaTek MT7621
- Flash: 32 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
Non-programmable "Power" LED
- Buttons: Reset and WPS
Instalation:
Install from TFTP
Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name
You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8
There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.
Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
|
||
|
Mikhail Zhilkin
|
f8b02130d2 |
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
|
||
Raymond Wang
|
3343ca7e68 |
ramips: add support for Xiaomi Mi Router CR660x series
Xiaomi Mi Router CR6606 is a Wi-Fi6 AX1800 Router with 4 GbE Ports.
Alongside the general model, it has three carrier customized models:
CR6606 (China Unicom), CR6608 (China Mobile), CR6609 (China Telecom)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256MB DDR3 (ESMT M15T2G16128A)
- Flash: 128MB NAND (ESMT F59L1G81MB)
- Ethernet: 1000Base-T x4 (MT7530 SoC)
- WLAN: 2x2 2.4GHz 574Mbps + 2x2 5GHz 1201Mbps (MT7905DAN + MT7975DN)
- LEDs: System (Blue, Yellow), Internet (Blue, Yellow)
- Buttons: Reset, WPS
- UART: through-hole on PCB ([VCC 3.3v](RX)(GND)(TX) 115200, 8n1)
- Power: 12VDC, 1A
Jailbreak Notes:
1. Get shell access.
1.1. Get yourself a wireless router that runs OpenWrt already.
1.2. On the OpenWrt router:
1.2.1. Access its console.
1.2.2. Create and edit
/usr/lib/lua/luci/controller/admin/xqsystem.lua
with the following code (exclude backquotes and line no.):
```
1 module("luci.controller.admin.xqsystem", package.seeall)
2
3 function index()
4 local page = node("api")
5 page.target = firstchild()
6 page.title = ("")
7 page.order = 100
8 page.index = true
9 page = node("api","xqsystem")
10 page.target = firstchild()
11 page.title = ("")
12 page.order = 100
13 page.index = true
14 entry({"api", "xqsystem", "token"}, call("getToken"), (""),
103, 0x08)
15 end
16
17 local LuciHttp = require("luci.http")
18
19 function getToken()
20 local result = {}
21 result["code"] = 0
22 result["token"] = "; nvram set ssh_en=1; nvram commit; sed -i
's/channel=.*/channel=\"debug\"/g' /etc/init.d/dropbear; /etc/init.d/drop
bear start;"
23 LuciHttp.write_json(result)
24 end
```
1.2.3. Browse http://{OWRT_ADDR}/cgi-bin/luci/api/xqsystem/token
It should give you a respond like this:
{"code":0,"token":"; nvram set ssh_en=1; nvram commit; ..."}
If so, continue; Otherwise, check the file, reboot the rout-
er, try again.
1.2.4. Set wireless network interface's IP to 169.254.31.1, turn
off DHCP of wireless interface's zone.
1.2.5. Connect to the router wirelessly, manually set your access
device's IP to 169.254.31.3, make sure
http://169.254.31.1/cgi-bin/luci/api/xqsystem/token
still have a similar result as 1.2.3 shows.
1.3. On the Xiaomi CR660x:
1.3.1. Login to the web interface. Your would be directed to a
page with URL like this:
http://{ROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/web/home#r-
outer
1.3.2. Browse this URL with {STOK} from 1.3.1, {WIFI_NAME}
{PASSWORD} be your OpenWrt router's SSID and password:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/misy-
stem/extendwifi_connect?ssid={WIFI_NAME}&password={PASSWO-
RD}
It should return 0.
1.3.3. Browse this URL with {STOK} from 1.3.1:
http://{MIROUTER_ADDR}/cgi-bin/luci/;stok={STOK}/api/xqsy-
stem/oneclick_get_remote_token?username=xxx&password=xxx&-
nonce=xxx
1.4. Before rebooting, you can now access your CR660x via SSH.
For CR6606, you can calculate your root password by this project:
https://github.com/wfjsw/xiaoqiang-root-password, or at
https://www.oxygen7.cn/miwifi.
The root password for carrier-specific models should be the admi-
nistration password or the default login password on the label.
It is also feasible to change the root password at the same time
by modifying the script from step 1.2.2.
You can treat OpenWrt Router however you like from this point as
long as you don't mind go through this again if you have to expl-
oit it again. If you do have to and left your OpenWrt router unt-
ouched, start from 1.3.
2. There's no official binary firmware available, and if you lose the
content of your flash, no one except Xiaomi can help you.
Dump these partitions in case you need them:
"Bootloader" "Nvram" "Bdata" "crash" "crash_log"
"firmware" "firmware1" "overlay" "obr"
Find the corespond block device from /proc/mtd
Read from read-only block device to avoid misoperation.
It's recommended to use /tmp/syslogbackup/ as destination, since files
would be available at http://{ROUTER_ADDR}/backup/log/YOUR_DUMP
Keep an eye on memory usage though.
3. Since UART access is locked ootb, you should get UART access by modify
uboot env. Otherwise, your router may become bricked.
Excute these in stock firmware shell:
a. nvram set boot_wait=on
b. nvram set bootdelay=3
c. nvram commit
Or in OpenWrt:
a. opkg update && opkg install kmod-mtd-rw
b. insmod mtd-rw i_want_a_brick=1
c. fw_setenv boot_wait on
d. fw_setenv bootdelay 3
e. rmmod mtd-rw
Migrate to OpenWrt:
1. Transfer squashfs-firmware.bin to the router.
2. nvram set flag_try_sys1_failed=0
3. nvram set flag_try_sys2_failed=1
4. nvram commit
5. mtd -r write /path/to/image/squashfs-firmware.bin firmware
Additional Info:
1. CR660x series routers has a different nand layout compared to other
Xiaomi nand devices.
2. This router has a relatively fresh uboot (2018.09) compared to other
Xiaomi devices, and it is capable of booting fit image firmware.
Unfortunately, no successful attempt of booting OpenWrt fit image
were made so far. The cause is still yet to be known. For now, we use
legacy image instead.
Signed-off-by: Raymond Wang <infiwang@pm.me>
|
||
Nick McKinney
|
e0a574d4b7 |
ramips: add support for Linksys EA6350 v4
Specifications: - SoC: MT7621DAT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 128 MB NAND - Ethernet: 5x 1GiE MT7530 - WiFi: MT7603/MT7613 - USB: 1x USB 3.0 This is another MT7621 device, very similar to other Linksys EA7300 series devices. Installation: Upload the generated factory.bin image via the stock web firmware updater. Reverting to factory firmware: Like other EA7300 devices, this device has an A/B router configuration to prevent bricking. Hard-resetting this device three (3) times will put the device in failsafe (default) mode. At this point, flash the OEM image to itself and reboot. This puts the router back into the 'B' image and allows for a firmware upgrade. Troubleshooting: If the firmware will not boot, first restore the factory as described above. This will then allow the factory.bin update to be applied properly. Signed-off-by: Nick McKinney <nick@ndmckinney.net> |
||
Eduardo Santos
|
3c97fb4346 |
ramips: add support for Xiaomi MiWifi 3C
This commit adds support for Xiaomi MiWiFi 3C device. Xiaomi MiWifi 3C has almost the same system architecture as the Xiaomi Mi WiFi Nano, which is already officially supported by OpenWrt. The differences are: - Numbers of antennas (4 instead of 2). The antenna management is done via the µC. There is no configuration needed in the software code. - LAN port assignments are different. LAN1 and WAN are interchanged. OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c OpenWrt developers forum page: https://forum.openwrt.org/t/support-for-xiaomi-mi-3c Specifications: - CPU: MediaTek MT7628AN (575MHz) - Flash: 16MB - RAM: 64MB DDR2 - 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA - Antennas: 4x external single band antennas - WAN: 1x 10/100M - LAN: 2x 10/100M - LED: 1x amber/blue/red. Programmable - Button: Reset MAC addresses as verified by OEM firmware: use address source LAN *:92 factory 0x28 WAN *:92 factory 0x28 2g *:93 factory 0x4 OEM firmware uses VLAN's to create the network interface for WAN and LAN. Bootloader info: The stock bootloader uses a "Dual ROM Partition System". OS1 is a deep copy of OS2. The bootloader start OS2 by default. To force start OS1 it is needed to set "flag_try_sys2_failed=1". How to install: 1- Use OpenWRTInvasion to gain telnet, ssh and ftp access. https://github.com/acecilia/OpenWRTInvasion (IP: 192.168.31.1 - Username: root - Password: root) 2- Connect to router using telnet or ssh. 3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp. 4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin to /tmp in router using ftp. 5- Enable UART access and change start image for OS1. ``` nvram set uart_en=1 nvram set flag_last_success=1 nvram set boot_wait=on nvram set flag_try_sys2_failed=1 nvram commit ``` 6- Installing Openwrt on OS1 and free OS2. ``` mtd erase OS1 mtd erase OS2 mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1 ``` Limitations: For the first install the image size needs to be less than 7733248 bits. Thanks for all community and especially for this device: minax007, earth08, S.Farid Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com> [wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to &wmac, convert to nvmem] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
Andrea Poletti
|
de0c380a5f |
ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
||
Tee Hao Wei
|
0c721434ea |
ramips: add support for Linksys EA8100 v2
Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Tom Wizetek (@wizetek) for testing. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> |
||
|
Tee Hao Wei
|
b232680f84 |
ramips: add support for Linksys EA8100 v1
Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
Jonathan Sturges
|
6d23e474ad |
ramips: add support for Amped Wireless ALLY router and extender
Amped Wireless ALLY is a whole-home WiFi kit, with a router (model ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are 11ac and based on MediaTek MT7621AT and MT7615N chips. The units are nearly identical, except the Extender lacks a USB port and has a single Ethernet port. Specification: - SoC: MediaTek MT7621AT (2C/4T) @ 880MHz - RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) - FLASH: 128MB NAND (Winbond W29N01GVSIAA) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch - USB: 1x USB3 (Router only) - BTN: Reset, WPS - LED: single RGB - UART: through-hole on PCB. J1: pin1 (square pad, towards rear)=3.3V, pin2=RX, pin3=GND, pin4=TX. Settings: 57600/8N1. Note regarding dual system partitions ------------------------------------- The vendor firmware and boot loader use a dual partition scheme. The boot partition is decided by the bootImage U-boot environment variable: 0 for the 1st partition, 1 for the 2nd. OpenWrt does not support this scheme and will always use the first OS partition. It will set bootImage to 0 during installation, making sure the first partition is selected by the boot loader. Also, because we can't be sure which partition is active to begin with, a 2-step flash process is used. We first flash an initramfs image, then follow with a regular sysupgrade. Installation: Router (ALLY-R1900K) 1) Install the flashable initramfs image via the OEM web-interface. (Alternatively, you can use the TFTP recovery method below.) You can use WiFi or Ethernet. The direct URL is: http://192.168.3.1/07_06_00_firmware.html a. No login is needed, and you'll be in their setup wizard. b. You might get a warning about not being connected to the Internet. c. Towards the bottom of the page will be a section entitled "Or Manually Upgrade Firmware from a File:" where you can manually choose and upload a firmware file. d: Click "Choose File", select the OpenWRT "initramfs" image and click "Upload." 2) The Router will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 3) Log into LuCI as root; there is no password. 4) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 5) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Extender (ALLY-00X19K) 1) This device requires a TFTP recovery procedure to do an initial load of OpenWRT. Start by configuring a computer as a TFTP client: a. Install a TFTP client (server not necessary) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6 c. Connect the Ethernet to the sole Ethernet port on the X19K. 2) Put the ALLY Extender in TFTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while connecting the power. b. As soon as the LED lights up green (roughly 2-3 seconds), release the button. 3) Start the TFTP transfer of the Initramfs image from your setup machine. For example, from Linux: tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin 4) The Extender will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 5) Log into LuCI as root; there is no password. 6) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 7) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Backup the OEM Firmware: ----------------------- There isn't any downloadable firmware for the ALLY devices on the Amped Wireless web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware may be stored on either /dev/mtd3 ("firmware") or /dev/mtd6 ("oem"). We can't be sure which was overwritten with the initramfs image, so backup both partitions to be safe. 1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware. 2) Under "Save mtdblock contents," first select "firmware" and click "Save mtdblock" to download the image. 3) Repeat the process, but select "oem" from the pull-down menu. Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow the TFTP recovery steps for the Extender, and use the backup image. * OpenWrt "Flash Firmware" interface: Upload the backup image and select "Force update" before continuing. Signed-off-by: Jonathan Sturges <jsturges@redhat.com> |
||
Chukun Pan
|
57cb387cfe |
ramips: add support for JCG Q20
JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> |
||
Bjørn Mork
|
2449a63208 |
ramips: mt7621: Add support for ZyXEL NR7101
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE with integrated directional 5G/LTE antennas. Specifications: - SoC: MediaTek MT7621AT - RAM: 256 MB - Flash: 128 MB MB NAND (MX30LF1G18AC) - WiFi: MediaTek MT7603E - Switch: 1 LAN port (Gigabiti) - 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC - SIM: 2 micro-SIM slots under transparent cover - Buttons: Reset, WLAN under same cover - LEDs: Multicolour green/red/yellow under same cover (visible) - Power: 802.3at PoE via LAN port The device is built as an outdoor ethernet to 5G/LTE bridge or router. The Wifi interface is intended for installation and/or temporary management purposes only. UART Serial: 57600N1 Located on populated 5 pin header J5: [o] GND [ ] key - no pin [o] RX [o] TX [o] 3.3V Vcc Remove the SIM/button/LED cover, the WLAN button and 12 screws holding the back plate and antenna cover together. The GPS antenna is fixed to the cover, so be careful with the cable. Remove 4 screws fixing the antenna board to the main board, again being careful with the cables. A bluetooth TTL adapter is recommended for permanent console access, to keep the router water and dustproof. The 3.3V pin is able to power such an adapter. MAC addresses: OpenWrt OEM Address Found as lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex) wwan0 usb0 random WARNING!! ISP managed firmware might at any time update itself to a version where all known workarounds have been disabled. Never boot an ISP managed firmware with a SIM in any of the slots if you intend to use the router with OpenWrt. The bootloader lock can only be disabled with root access to running firmware. The flash chip is physically inaccessible without soldering. Installation from OEM web GUI: - Log in as "supervisor" on https://172.17.1.1/ - Upload OpenWrt initramfs-recovery.bin image on the Maintenance -> Firmware page - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Installation from OEM ssh: - Log in as "root" on 172.17.1.1 port 22022 - scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp - Prepare bootloader config by running: nvram setro uboot DebugFlag 0x1 nvram setro uboot CheckBypass 0 nvram commit - Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - (optional) Copy OpenWrt to the recovery partition. See below - Sysupgrade to the OpenWrt sysupgrade image and reboot Copying OpenWrt to the recovery partition: - Verify that you are running a working OpenWrt recovery image from flash - ssh to root@192.168.1.1 and run: fw_setenv CheckBypass 0 mtd -r erase Kernel2 - Wait while the bootloader mirrors Image1 to Image2 NOTE: This should only be done after successfully booting the OpenWrt recovery image from the primary partition during installation. Do not do this after having sysupgraded OpenWrt! Reinstalling the recovery image on normal upgrades is not required or recommended. Installation from Z-Loader: - Halt boot by pressing Escape on console - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt - Wait for OpenWrt to boot and ssh to root@192.168.1.1 - Sysupgrade to the OpenWrt sysupgrade image NOTE: ATNR will write the recovery image to both primary and recovery partitions in one go. Booting from RAM: - Halt boot by pressing Escape on console - Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu - Press "4" to select "4: Entr boot command line interface." - Set up a tftp server to serve the OpenWrt initramfs-recovery.bin image at 10.10.10.3 - Load it using "tftpboot 0x88000000 initramfs-recovery.bin" - Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL header This method can also be used to RAM boot OEM firmware. The warning regarding OEM applies! Never boot an unknown OEM firmware, or any OEM firmware with a SIM in any slot. NOTE: U-Boot configuration is incomplete (on some devices?). You may have to configure a working mac address before running tftp using "setenv eth0addr <mac>" Unlocking the bootloader: If you are unebale to halt boot, then the bootloader is locked. The OEM firmware locks the bootloader on every boot by setting DebugFlag to 0. Setting it to 1 is therefore only temporary when OEM firmware is installed. - Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware - Run "fw_setenv DebugFlag 0x1" in OpenWrt NOTE: OpenWrt does this automatically on first boot if necessary NOTE2: Setting the flag to 0x1 avoids the reset to 0 in known OEM versions, but this might change. WARNING: Writing anything to flash while the bootloader is locked is considered extremely risky. Errors might cause a permanent brick! Enabling management access from LAN: Temporary workaround to allow installing OpenWrt if OEM firmware has disabled LAN management: - Connect to console - Log in as "root" - Run "iptables -I INPUT -i br0 -j ACCEPT" Notes on the OEM/bootloader dual partition scheme The dual partition scheme on this device uses Image2 as a recovery image only. The device will always boot from Image1, but the bootloader might copy Image2 to Image1 under specific conditions. This scheme prevents repurposing of the space occupied by Image2 in any useful way. Validation of primary and recovery images is controlled by the variables CheckBypass, Image1Stable, and Image1Try. The bootloader sets CheckBypass to 0 and reboots if Image1 fails validation. If CheckBypass is 0 and Image1 is invalid then Image2 is copied to Image1. If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to Image2. If CheckBypass is 1 then all tests are skipped and Image1 is booted unconditionally. CheckBypass is set to 1 after each successful validation of Image1. Image1Try is incremented if Image1Stable is 0, and Image2 is copied to Image1 if Image1Try is 3 or larger. But the bootloader only tests Image1Try if CheckBypass is 0, which is impossible unless the booted image sets it to 0 before failing. The system is therefore not resilient against runtime errors like failure to mount the rootfs, unless the kernel image sets CheckBypass to 0 before failing. This is not yet implemented in OpenWrt. Setting Image1Stable to 1 prevents the bootloader from updating Image1Try on every boot, saving unnecessary writes to the environment partition. Keeping an OpenWrt initramfs recovery as Image2 is recommended primarily to avoid unwanted OEM firmware boots on failure. Ref the warning above. It enables console-less recovery in case of some failures to boot from Image1. Signed-off-by: Bjørn Mork <bjorn@mork.no> |
||
Piotr Dymacz
|
914563e286 |
uboot-envtools: drop shebang from uci-defaults and lib files
These files are sourced and non-executable, a shebang is redundant. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
Lech Perczak
|
59d065c9f8 |
ramips: add support for ZTE MF283+
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.
Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
internally wired in parallel by 0-Ohm resistors, handled entirely by
internal WWAN modem.
- USB: internal miniPCIe slot for modem,
unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
phone (bicolor, controlled by modem), Signal,
4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.
Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.
There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.
(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
persistent environment for next installation.
- If you ever might want to return to vendor firmware,
BACK UP CONTENTS OF YOUR FLASH NOW.
For this router, commonly used by mobile networks,
plain vendor images are not officially available.
To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
most important, and copy them over network to your PC. But in case
anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
and execute sysupgrade.
(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
(no quotes), for example using tftpd:
cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
minute.
Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery
(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
your backup taken before OpenWrt installation, and /dev/mtd3 is the
"firmware" partition.
(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
with firmware backup you took during installation, or by vendor
firmware obtained elsewhere.
A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
modem, so it work independently of OpenWrt.
Tested to work even before OpenWrt booted.
I managed to open up modem's shell via ADB,
and found from its kernel logs, that FXS and its LED is indeed controlled
by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
each and every one of them manually, so this might not be complete -
it looks like bicolor LED is used for FXS, possibly to support
dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
read command, due to using 4k sectors throughout the target. I decided
to keep it at the moment, to avoid breaking existing devices - I
identified one potentially affected, should this be limited to under
4MB of Flash. The difference between sysupgrade durations is whopping
3min vs 8min, so this is worth pursuing.
In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.
Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.
A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
uqmi did connect successfully, once I selected correct PDP context
type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
added to 51-android.rules like so:
SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"
While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
||
Dmytro Oz
|
c2a7bb520a |
ramips: mt7621: add support for Xiaomi Mi Router 4
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for the RAM (256Mib→128Mib), LEDs and gpio (MiNet button). Specifications: Power: 12 VDC, 1 A Connector type: barrel CPU1: MediaTek MT7621A (880 MHz, 4 cores) FLA1: 128 MiB (ESMT F59L1G81MA) RAM1: 128 MiB (ESMT M15T1G1664A) WI1 chip1: MediaTek MT7603EN WI1 802dot11 protocols: bgn WI1 MIMO config: 2x2:2 WI1 antenna connector: U.FL WI2 chip1: MediaTek MT7612EN WI2 802dot11 protocols: an+ac WI2 MIMO config: 2x2:2 WI2 antenna connector: U.FL ETH chip1: MediaTek MT7621A Switch: MediaTek MT7621A UART Serial [o] TX [o] GND [o] RX [ ] VCC - Do not connect it MAC addresses as verified by OEM firmware: use address source LAN *:c2 factory 0xe000 (label) WAN *:c3 factory 0xe006 2g *:c4 factory 0x0000 5g *:c5 factory 0x8000 Flashing instructions: 1.Create a simple http server (nginx etc) 2.set uart enable To enable writing to the console, you must reset to factory settings Then you see uboot boot, press the keyboard 4 button (enter uboot command line) If it is not successful, repeat the above operation of restoring the factory settings. After entering the uboot command line, type: setenv uart_en 1 saveenv boot 3.use shell in uart cd /tmp wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1 mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0 nvram set flag_try_sys1_failed=1 nvram commit reboot 4.login to the router http://192.168.1.1/ Installation via Software exploit Find the instructions in the https://github.com/acecilia/OpenWRTInvasion Signed-off-by: Dmytro Oz <sequentiality@gmail.com> [commit message facelift, rebase onto shared DTSI/common device definition, bump uboot-envtools] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
|
Michael Pratt
|
a459696eb1 |
ramips: add support for Senao Engenius ESR600H
FCC ID: A8J-ESR750H
Engenius ESR600H is an indoor wireless router with a gigabit switch,
2.4 GHz and 5 GHz wireless, internal and external antennas, and a USB port.
**Specification:**
- RT3662F MIPS SOC, 5 GHz WMAC (2x2)
- RT5392L PCI on-board, 2.4 GHz (2x2)
- AR8327 RGMII, 7-port GbE, 25 MHz clock
- 40 MHz reference clock
- 8 MB FLASH 25L6406EM2I-12G
- 64 MB RAM
- UART at J12 (unpopulated)
- 2 internal antennas (5 GHz)
- 2 external antennas (2.4 GHz)
- 9 LEDs, 1 button (power, wps, wifi2g, wifi5g, 5 LAN/WAN)
- USB 2 port (GPIO controlled power)
**MAC addresses:**
MAC Addresses are labeled as WAN and WLAN
U-boot environment has the the vendor MAC address for ethernet
MAC addresses in "factory" are part of wifi calibration data
eth0.2 WAN *:13:e7 u-boot-env wanaddr
eth0.1 ---- *:13:e8 u-boot-env wanaddr + 1
phy0 WLAN *:14:b8 factory 0x8004
phy1 ---- *:14:bc factory 0x4
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Network Setting --> Tools --> Firmware
Click Browse and select the factory.dlf image
Click Continue to confirm and wait 6 minutes or more...
Method 2: Serial console to load TFTP image:
(see TFTP recovery)
**Return to OEM:**
Unlike most Engenius boards, this does not have a 'failsafe' image
the only way to return to OEM is serial access to uboot
Unlike most Engenius boards, public images are not available...
so the only way to return to OEM is to have a copy
of the MTD partition "firmware" BEFORE flashing openwrt.
**TFTP recovery:**
Unlike most Engenius boards, TFTP is reliable here
however it requires serial console access
(soldering pins to the UART pinouts)
build your own image...
with 'ramdisk' selected under 'Target Images'
rename initramfs-kernel.bin to 'uImageESR-600H'
make the file available on a TFTP server at 192.168.99.8
interrupt boot by holding or pressing '4' in serial console
as soon as board is powered on
`tftpboot 0x81000000`
`bootm 0x81000000`
perform a sysupgrade
**Format of OEM firmware image:**
This Engenius board uses the Senao proprietary header
with a unique Product ID. The header for factory.bin is
generated by the mksenaofw program included in openwrt.
.dlf file extension is also required for OEM software to accept it
**Note on using OKLI:**
the kernel is now too large for the bootloader to handle
so OKLI is used via the `kernel-loader` image command
recently in master several other ramips boards have the same problem
'Kernel panic - not syncing: Failed to find ralink,rt3883-sysc node'
see commit
|
||
Adrian Schmutzler
|
af07c6de9c |
uboot-envtools: ramips: use full names for Xiaomi Mi Routers
This updates uboot-envtools with the updated names from ramips
target.
Fixes:
|
||
Ataberk Özen
|
4287f73989 |
ramips: add support for Xiaomi Mi Router 4C
This commit adds support for Xiaomi's Mi Router 4C device.
Specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LEDs: 2x yellow/blue. Programmable (labelled as power on case)
- Non-programmable (shows WAN activity)
- Button: Reset
How to install:
1- Use OpenWRTInvasion to gain telnet and ftp access.
2- Push openwrt firmware to /tmp/ using ftp.
3- Connect to router using telnet. (IP: 192.168.31.1 -
Username: root - No password)
4- Use command "mtd -r write /tmp/firmware.bin OS1" to flash into
the router..
5- It takes around 2 minutes. After that router will restart itself
to OpenWrt.
Signed-off-by: Ataberk Özen <ataberkozen123@gmail.com>
[wrap commit message, bump PKG_RELEASE for uboot-envtools, remove
dts-v1 from DTS, fix LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
||
Antonis Kanouras
|
cb8c94f516 |
uboot-envtools: support Xiaomi Mi Router 3G v2/4A Gigabit
Add support for the following devices: - Xiaomi Mi Wi-Fi Router 3G v2 - Xiaomi Mi Router 4A Gigabit Edition Signed-off-by: Antonis Kanouras <antonis@metadosis.eu> [add explicit case for 4A, bump PKG_RELEASE, improve commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
J. Scott Heppler
|
620f9c7734 |
ramips: add support for Linksys EA7300 v2
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Winbond W632GG6MB-12 (256M DDR3-1600)
* Flash: Winbond W29N01HVSINA (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
|