Commit Graph

28227 Commits

Author SHA1 Message Date
David Bauer
43e9cded06 mpc85xx: correct WS-AP3715i eth LED assignment
Ethernet LED assignments were incorrectly swapped. Fix the assignment
logic so the correct LED is illuminated for the LAN LEDs.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8037417744)
2023-09-21 01:11:11 +02:00
Felix Fietkau
7e55f20c1f kernel: backport support for renaming netdevs while up
Will be used in upcoming hostapd changes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 77c45ddd86)
2023-09-18 14:25:18 +02:00
Andreas Böhler
385a50f02d
ipq40xx: fix image building for ZTE MF287 series
For the ZTE MF287 series, a special recovery image is built. The Makefile
worked fine on snapshot, but created corrupt images on the 23.05 images.
By using the appropriate variable, this should be fixed.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit a9cc3708e0)
2023-09-18 11:50:08 +02:00
Max Qian
2dc284a79a
ramips: RT1800: fix invalid octal number error
This commit removes the padded zeros in the date formatting.
The padded zeros from the date command causes the numbers
to be interpreted as an octal number by printf. Months, days,
and years with the number 08 or 09 raise an error in printf as an
"invalid octal number" and get interpreted as a zero.

Signed-off-by: Max Qian <public@maxqia.com>
(cherry picked from commit 794349a28a)
2023-09-17 22:46:01 +02:00
Matthijs Kooijman
c3be832427
ath79: fix packetloss on some WLR-7100
On some WLR-7100 routers, significant packet loss was observed. This is
fixed by configuring a delay on the GMAC0 RXD and RXDV lines.

The values used in this commit are copied from the values used by the
stock firmare (based on register dumping).

Out of four test routers, the problem was consistently observed on two.
It is unclear what the relevant difference is exactly (the two working
routers were v1 001 with AR1022 and v1 002 with AR9342, the two broken
routers were both v1 002 with AR1022). All PCB routing also seems
identical, so maybe there is some stray capacitance on some of these
that adds just enough delay or so...

With this change, the packet loss disappears on the broken routers,
without introducing new packet loss on the previously working routers.

Note that the PHY *also* has delays enabled (through
`qca,ar8327-initvals`) on both RX and TX lines, but apparently that is
not enough, or it is not effective (registers have been verified to be
written).

For detailed discussion of this issue and debug history, see
https://forum.openwrt.org/t/sitecom-wlr-7100-development-progress/79641

Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
(cherry picked from commit d2ce3a61aa)
2023-09-17 16:39:47 +02:00
Mathew McBride
d536f398eb kernel: ensure VFIO related suboptions are disabled
These suboptions (PLATFORM, FSL_MC and MLX5_VFIO_PCI)
may be prompted for when VFIO is enabled, regardless of
architecture.

These are not related to the main vfio use case
(passthrough of PCIe devices)

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(5.15 version of abc536f547)
2023-09-16 21:00:38 +02:00
Mathew McBride
c90005c58a x86: remove built-in vhost-net driver
This is now available as a kmod package (kmod-vhost-net).

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 8b1cc1582a)
2023-09-16 21:00:38 +02:00
INAGAKI Hiroshi
6897270491 mvebu: add reset delays of PHYs for Fortinet FortiGate 50E
Add reset-(de)assert-us to ethernet PHYs on Fortinet FortiGate 50E to
solve instability after HW resetting of PHYs. (ex.: restarting "network"
service, etc...)

Fixes: #13391
Fixes: 102dc5a625 ("mvebu: add support for Fortinet FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(cherry picked from commit 5c65224d8f)
2023-09-16 12:40:03 +02:00
Brian Norris
10aee60361
ipq806x: Correct OnHub sysupgrade config logic
There's a typo in here: board_name is a function, not a variable. This
issue was pointed out on the OpenWrt forum.

Closes: #13409

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(cherry picked from commit 7b78a19e6a)
2023-09-16 12:02:23 +02:00
Jonas Gorski
6c60bbbc94 x86: geode: fix hwrng register accesses
When the membase and pci_dev pointer were moved to a new struct in priv,
the actual membase users were left untouched, and they started reading
out arbitrary memory behind the struct instead of registers. This
unfortunately turned the RNG into a constant number generator, depending
on the content of what was at that offset.

To fix this, update geode_rng_data_{read,present}() to also get the
membase via amd_geode_priv, and properly read from the right addresses
again.

Closes #13417.

Reported-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Tested-by: Timur I. Davletshin <timur.davletshin@gmail.com>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit 09d13cd8d8)
2023-09-14 09:12:57 +02:00
Piotr Dymacz
3cc223243b ramips: add support for ALFA Network AX1800RM
ALFA Network AX1800RM (FCC ID: 2AB877621) is a dual-band Wi-Fi 6
(AX1800) router, based on MediaTek MT7621A + MT79x5D platform.

Specifications:

- SOC:      MT7621A (880 MHz)
- DRAM:     DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash:    16 MiB SPI NOR (EN25QH128A-104HIP)
- Ethernet: 4x 10/100/1000 Mbps (SOC's built-in switch)
- Wi-Fi:    2x2:2 2.4/5 GHz (MT7905DAN + MT7975DN)
            (MT7905DAN doesn't support background DFS scan/BT)
- LED:      6x green, 1x green/red
- Buttons:  2x (reset, WPS)
- Antenna:  4x external, non-detachable omnidirectional
- UART:     1x 4-pin (2.54 mm pitch, J4, not populated)
- Power:    12 V DC/1 A (DC jack)

MAC addresses:

LAN:     00:c0:ca:xx:xx:4e (factory 0x4, +2)
WAN:     00:c0:ca:xx:xx:4f (factory 0x4, +3)
2.4 GHz: 00:c0:ca:xx:xx:4c (factory 0x4, device's label)
5 GHz:   00:c0:ca:xx:xx:4c (factory 0xa)

Flash instructions for web-based U-Boot recovery:

1. Power the device with WPS button pressed and wait around 10 seconds.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'recovery' image.

The device runs LEDE 17.01 (kernel 4.4.x) based firmware with 'failsafe'
mode available which allows alternative upgrade method:

1. Run device in 'failsafe' mode and change password for default user.
2. SSH to the device, transfer 'sysupgrade' image and perform upgrade
   in forced mode, without preserving settings: 'sysupgrade -n -F ...'.

Other notes:

If you own early version of this device, the vendor firmware might
refuse OpenWrt image because of missing custom header. In that case,
ask vendor's customer support for stock firmware without custom header
support/requirement.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit f1aaa267f0)
2023-09-11 13:49:07 +02:00
Shiji Yang
9df9126320 ramips: pinctrl: support requesting different functions for same group
MT7620 wireless radio needs change the pin group function between
"gpio" and "pa" during the calibration process. However, ralink
pinctrl driver doesn't support requesting different functions for
the same group. This patch enables pinctrl consumers to perform
such operations.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit b4ea49ad44)
2023-09-04 23:00:35 +01:00
Daniel Golle
b2d264dc68 mediatek: mt7622: set DEVICE_DTC_ADDR for BPi-R64
Relocating the device tree is required for being apply to apply
device tree overylay at boot.

Fixes: 34bb33094a ("mediatek: use updated device tree overlay mechanism for BPi-R64")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit a8cbee8e2d)
2023-09-04 23:00:35 +01:00
Daniel Golle
3967c26974 mediatek: filogic: remove stray quote
When adapting the network configuration for MT7988 RFB a stray quote
was left in a script. Remove it to fix generating the default network
configuration.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 8f5986355c)
2023-09-04 23:00:34 +01:00
Daniel Golle
625d19c1e2 generic: sync MediaTek Ethernet driver with upstream
Import commits from upstream Linux replacing some downstream patches.
Move accepted patches from pending-{5.15,6.1} to backport-{5.15,6.1}.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f631c7bbb1)
2023-09-04 23:00:34 +01:00
Daniel Golle
230c09d203 mediatek: add support for Ubiquiti UniFi 6 LR v3
Some recent models of the Ubiquiti Networks UniFi 6 LR access point
come with a RealTek RTL8211FS 1000M/100M/10M PHY instead of the
Aquantia AQR112 2500M/1000M/100M/10M PHY used in both v1 and v2. Add
build for this variant so we can support Ethernet with the PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit a0f4eadf6a)
2023-09-04 23:00:34 +01:00
Daniel Golle
ed370ec424 mediatek: generate bootloader artifacts for mt7988_rfb
Switch to OpenWrt uImage.FIT bootmethod and include various bootloader
artifacts with the generated binaries.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 035a88ae55)
2023-09-04 23:00:34 +01:00
Daniel Golle
87ef305984 mediatek: improve mt7981.dtsi
* re-factor WED components to boot fine also on limited loaders
 * add LEDs of integrated GE PHY

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3ef8760e87)
2023-09-04 23:00:34 +01:00
Daniel Golle
ffede121f8 mediatek: filogic: improve pinctrl drivers
Set correct pull-type data and add additional uart groups for MT7981.
Assign functions to configure pin bias for MT7986.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9f8fde216d)
2023-09-04 23:00:34 +01:00
Daniel Golle
5a9720945f mediatek: i2c: mt65xx: allow optional pmic clock
Using the I2C host controller on the MT7981 SoC requires 4 clocks to
be enabled. One of them, the pmic clk, is only enabled in case
'mediatek,have-pmic' is also set which has other consequences which
are not desired in this case.

Allow defining a pmic clk even in case the 'mediatek,have-pmic' propterty
is not present and the bus is not used to connect to a pmic, but may
still require to enable the pmic clock.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2544dc34f2)
2023-09-04 23:00:34 +01:00
Daniel Golle
88c12d6632 mediatek: re-add dropped properties on BPi-R3
Unfortunately some device tree properties have slipped under the table
when switching from our downstream device tree.

Bring back 3W power for SFP cages and restore thermal trip points to
make sense again.

Fixes: 7a0ec001ff ("mediatek: sync MT7986 device trees with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 06a150aed7)
2023-09-04 23:00:34 +01:00
Christian Marangi
cf08db988b generic: backport initial LEDs hw control support
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.

Refresh every patch and add the additional config flag for QCA8K new
LEDs support.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0a4b309f41)
2023-09-04 23:00:34 +01:00
John Audia
8bf25dba77 kernel: bump 5.15 to 5.15.129
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.129

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 1db566b692)
[Refresh on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-09-03 13:45:11 +02:00
John Audia
3c1721ae03 kernel: bump 5.15 to 5.15.128
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.128

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit e80a387517)
[Refresh on OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-09-03 13:45:07 +02:00
Felix Fietkau
56827dac01 kernel: allow adding devices without hw offload to a hw flowtable
This allows supporting a mix of devices with or without hw offloading support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c5b7be8316)
2023-09-01 15:17:30 +02:00
David Bauer
e74a4b509f mediatek: enable NMBM remapping for NWA50AX Pro UBI
Don't skip remapping of the UBI area for the ZyXEL NWA50AX Pro. This is
due to the kernel being loaded from the UBI partition by U-Boot.

Link: https://github.com/openwrt/openwrt/pull/13335

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 6dc0675e5b)
2023-08-25 21:42:53 +02:00
Shiji Yang
d792d20832 ath79: fix first reboot issue on Netgear WNDR4300 v2 and WNDR4500 v3
From the Netgear u-boot GPL code[1]. Bootloader always unconditionally
marks block 768, 1020 - 1023 as bad blocks on each boot. This may lead
to conflicts with the OpenWrt nand driver since these blocks may be good
blocks. In this case, U-boot will override the oob of these blocks so
that break the ubi volume. The system will be damaged after first reboot.
To avoid this issue, manually skip these blocks by using "mtd-concat".

[1] https://www.downloads.netgear.com/files/GPL/EX7300v2series-V1.0.0.146_gpl_src.tar.bz2.zip

Fixes: https://github.com/openwrt/openwrt/issues/8878
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 12f53724c6)
2023-08-24 20:45:12 +02:00
Shiji Yang
7eda621404 ath79: rework Netgear nand devices image recipe
In Netgear u-boot GPL code, nand devices uses this formula to locate the
rootfs offset.

offset = (((128 + KERNEL_SIZE) / BLOCK_SIZE) + 1) * BLOCK_SIZE;

Howerver, WNDR4500 source code incorrectly define the nand block size to
64k. In some cases, it causes u-boot can't get the correct rootfs offset,
which result in boot failure. This patch workaround it by padding kernel
size to (128k * n - 128 - 1). The additional char '\0' is used to ensure
the (128 + KERNEL_SIZE) can't be divided by the BLOCK_SIZE.

Fixes: https://github.com/openwrt/openwrt/issues/13050
Fixes: 3c1512a25d ("ath79: optimize the firmware recipe for Netgear NAND devices")
Tested-by: Yousaf <yousaf465@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 0f9b8aa3f5)
2023-08-24 20:45:01 +02:00
Stefan Agner
f445c38263 mediatek: filogic: wax220: cleanup device tree
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.

Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit 4af06aaf33)
2023-08-22 13:40:10 +02:00
Stefan Agner
16aecc12c2 mediatek: filogic: wax220: support factory image
Enable building a factory image which can be flashed through the OEM
firmware's web interface. It seems that the web interface requires a
minimum file size of 10MiB, otherwise it will not accept the image.

The update image is a regular sysupgrade tarball packed in a Netgear
encrypted image. The Netgear encrypted image is the same as used in
WAX202 or WAX206, including the encryption keys and IV.

This adds a script which creates the rootfs_data volume on first
startup. This is required since the OEM firmware's sysupgrade scripts
do not create such a paritition. Note that any script ordered after
70_initramfs_test will not get executed on initramfs. Hence this new
script 75_rootfs_prepare won't create the rootfs_data volume when
using the recovery initramfs.

Also, this deletes the kernel_backup and rootfs_backup volumes in case
we have to create the rootfs_data volumes. This makes sure that
OpenWrt is the actual backup firmware instead of the stock firmware.

References in WAX220 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX220-V1.0.2.8-gpl-src.tar.gz

* package/base-files/files/lib/upgrade/nand.sh:186
  Creation of rootfs_data is disabled

* Uboot-upstream/board/mediatek/common/ubi_helper.c
  Automatic creation of UBI backup volumes

Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit fa9d977f97)
2023-08-22 13:39:57 +02:00
David Bauer
99d9519bac mediatek: enable NWA50AX Pro eth LEDs
Enable the ethernet LED's on the ZyXEL NWA50AX Pro to show link-state as
well as activity.

Both LED's are configured pulsing.

AMBER | 10/100
GREEN | 1000
A+G   | 2500

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4c0fdad7ea)
2023-08-22 13:39:29 +02:00
David Bauer
9ed01992f3 mediatek: add missing packages for Acer Predator W6
Add missing packages for creating the overlay filesystem.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c35ff41ccc)
2023-08-22 12:25:13 +02:00
Andreas Böhler
e658eee813 ipq4019: add support for ZTE MF287 Pro aka DreiNeo Pro
The ZTE MF287 Pro is a LTE router used (exclusively?) by the network
operator "3". It is very similar to the MF287+, but the hardware layout
and partition layout have changed quite a bit.

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12
WiFi: 802.11a/b/g/n/ac SoC-integrated
USB: 1x 2.0

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m17
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd17 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 17
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Other Notes
===========

Contrary to the stock firmware, the USB port on the back can be used.

There is one GPIO Switch "Power button blocker" which, if enabled, does not
trigger a reset of the SoC if the modem reboots. If disabled, the SoC is
rebooted along with the modem. The modem can be rebooted via the exported
GPIO "modem-reset" in /sys/class/gpio.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit edfe91372a)
2023-08-21 21:41:12 +02:00
Mathew McBride
a506859f60 armsr: add kmod-sfp to default device profile
This brings the 23.05 branch into parity with the main.
kmod-sfp was in the main branch profile but not the 23.05 version.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-08-19 15:11:55 +02:00
Mathew McBride
cebed31c1f armsr: armv8: fix invalid symbol value for FSL_ENETC_QOS
The kernel FSL_ENETC_QOS option is only a compile time
option, it does not result in a separate module being built.

Set it to 'y' to resolve a warning from the kernel compile:

.config:2654:warning: symbol value 'm' invalid for FSL_ENETC_QOS

Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c3151b6f04 ("armvirt: 64: add support for other SystemReady-compatible vendors")
(cherry picked from commit 7770d08e2b)
2023-08-19 15:11:55 +02:00
Mathew McBride
3c316f3e24 armsr: armv8: package and select MDIO driver for Thunder SoC's
This MDIO driver was already being built, but not installed due
to being selected by the ThunderX Ethernet driver.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 0018b33531)
2023-08-19 15:11:55 +02:00
Mathew McBride
2a46bd9a01 armsr: add Marvell (Cavium) ThunderX2 network driver
The initial armv8 module incorrectly labelled the Thunder(v1) as
supporting the ThunderX2, when they have different drivers.

Add kmod-octeon-tx2 to support the newer devices.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 7c5bdff9c4)
2023-08-19 15:11:55 +02:00
Mathew McBride
3477c79c6b armsr: armv8: add bcmgenet (Raspberry Pi 4 GENET) to profile
kmod-bcmgenet is needed for Ethernet support on the
Raspberry Pi 4.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 911ee97774)
2023-08-19 15:11:55 +02:00
Mathew McBride
80d1eb4c2a armsr: armv8: add Broadcom GENET and MDIO modules
These are used by common Broadcom SoC's like
the BCM2711 (RPi4) and iProc network processor.

Tested on the RPi4B using the Raspberry Pi
UEFI+ACPI firmware[1].

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - https://github.com/pftf/RPi4

(cherry picked from commit 27ca83c627)
2023-08-19 15:11:55 +02:00
Mathew McBride
dfb159c04b armsr: armv8: enable AHCI/SATA controllers for mvebu,qoriq,juno
When comparing the generated OpenWrt .config to the Linux arm64
defconfig, I noticed these SATA controllers were not included.
As they may be used as a boot drive, they should be built into
the kernel.

CONFIG_SATA_MVEBU is for Marvell platforms.
CONFIG_SATA_QORIQ is for NXP Layerscape.
CONFIG_SATA_SIL24 is for Arm's Juno development board, see Linux
kernel commit d7c38ff1cd86 ("arm64: defconfig: Add Juno SATA
controller").

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit 9cb173e9f1)
2023-08-19 15:11:55 +02:00
Mathew McBride
daf99a12e1 armsr: armv8: synchronize PCIE related options with arm64 defconfig
This turns on various PCI related options which are enabled
in the Linux kernel arch/arm64/configs/defconfig but not
yet in the OpenWrt config.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit 15d3536c9d)
2023-08-19 15:11:55 +02:00
Mathew McBride
24b35fdce9 armsr: armv8: enable Broadcom arch'es
This is part of an effort to reduce differences between
the OpenWrt armsr/armv8 config and Linux arm64 defconfig.

This enables CONFIG_ARCH_BCM and downstream
CONFIG_ARCH_BCM2835 (= BCM2711 like Raspberry Pi 4)
and CONFIG_ARCH_BCM_IPROC (Broadcom iProc packet processors).

The broadband specific SoC's (ARCH_BCMBCA) are left out
as it is assumed these will not be doing EFI boot.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.5/5.15 version of commit df23eed179)
2023-08-19 15:11:55 +02:00
Mathew McBride
cb0534d2ed armsr: armv8: enable CONFIG_ARCH_RENESAS
Renesas markets several embedded Arm64 SoCs in the
RZ series (RZ/G, RZ/V), so should be enabled in
a general purpose target.

Automotive (R-Car) SoC's are not enabled by this change.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit 1ff4f4df23)
2023-08-19 15:11:55 +02:00
Mathew McBride
14f7254a6a armsr: enable ACPI_BUTTON
A review of the generated OpenWrt kernel .config
vs the Linux arm64 defconfig showed that this
option was not being enabled, as it is disabled
in OpenWrt's generic config.

ACPI_BUTTON is needed to report and respond to
power button events, so it should be enabled.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit c4c60e4b19)
2023-08-19 15:11:55 +02:00
Mathew McBride
f517d8a518 armsr: armv8: sync CPU features, EFI, CMA and scheduler options with Linux defconfig
To bring the armsr/armv8 kernel configuration closer to the Linux
arm64 defconfig, synchronize options related to CPU features
(especially more recent Armv8.X variants), scheduler, EFI vars,
CMA and scheduler options.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version commit 22e0c7be47)
2023-08-19 15:11:55 +02:00
Mathew McBride
88e7fe8741 armsr: armv8: enable KVM host
x86/64 enables support for KVM so I can't see a reason why
not on armsr/armv8 as well.

Arm CPU errata workaround items related to virtualization
are also enabled by this change.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit e505873e65)
2023-08-19 15:11:55 +02:00
Mathew McBride
e306e46a8d armsr: armv8: sync Arm64 erratum options with kernel defconfig
To reduce differences with the Linux arm64 defconfig,
sync the enabled erratum items with defconfig.

There are still some options not selected due to
CONFIG_KVM or other options not enabled in OpenWrt
by default.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(23.05/5.15 version of commit 5c4239ac3f)
2023-08-19 15:11:55 +02:00
Tianling Shen
6eb6a75b8d kernel: modules: add xdp-sockets-diag support
Support for PF_XDP sockets monitoring interface used by the ss tool.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 06e64f9b36)
2023-08-19 15:06:52 +02:00
John Audia
097d6890ba kernel: bump 5.15 to 5.15.127
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.127

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 973c5d4a1d)
2023-08-19 11:59:15 +02:00
Hauke Mehrtens
dd30399cae x86: Add virtualization time sync support
This compiles the CONFIG_PTP_1588_CLOCK support into the kernel binary
and activates the drivers for KVM and VMware which allow syncing the
host time with the VM when OpenWrt is running in a VM. With this change
the CONFIG_HYPERV_UTILS driver is now build into the kernel, because it
depends on the PTP framework being compiled in. CONFIG_HYPERV_UTILS was
build as a module, but not packages before.

Fixes: #13277
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 54d470ed0e)
2023-08-15 17:19:05 +02:00
Hauke Mehrtens
f28a2a5094 x86: Activate CONFIG_PCIEASPM
This activates PCI Express ASPM control in Linux. Without this option it
is completely controlled by the BIOS, now Linux will take over and apply
some workarounds if needed.

Fixes: #13248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ff71035751)
2023-08-15 17:19:05 +02:00
Ivan Pavlov
5569b92cb3 ramips: improve Xiaomi mi-mini indications
Sets status indications led color on Xiaomi mi-mini router as other Xiaomi routers

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit 54e5e396c5)
2023-08-15 17:19:05 +02:00
Robert Marko
4956ff40c5 ipq40xx: meraki: define DTB load address
It seems that the Meraki bootloader does not respect the kernel ARM booting
specification[1] that requires that address where DTB is located needs to
be 64-bit aligned and often places the DTB on a non 64-bit aligned address
and then kernel fails to find the DTB magic and fails to boot.
Even worse, there is no prints until early printk is enabled and then its
visible that kernel is trying to find the ATAG-s as DTB was not found or
is invalid.

Unifi 6 devices had the same issue and it can be solved by passing the
load adress as part of the FIT image.
It seems that the vendor was aware of the issue and is always relocating
the DTB to 0x89000000, so lets just do the same.

Now that booting is reliable, reenable default images for the Meraki MR33
and MR74 devices.

Reviewed-by: Lech Perczak lech.perczak@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f1c80445bd)
2023-08-15 17:16:05 +02:00
Robert Marko
5cecf9aec8 ipq40xx: meraki: remove swconfig in DEVICE_PACKAGES
ipq40xx was converted to DSA and swconfig is not being included at all in
the default packages so there is no need to drop it from device packages.

Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bb4a25860f)
2023-08-15 17:16:05 +02:00
Robert Marko
73aa78c4a0 ipq40xx: commonize Meraki recipe
MR33 and MR74 share pretty much everything in the image recipe, so lets
extract a common recipe to avoid duplication.

Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9e9dc1890c)
2023-08-15 17:16:05 +02:00
John Audia
a23aa1c55a kernel: bump 5.15 to 5.15.126
1. Disable unneeded errata Kconfig symbols
2. Update kernel

Changelog: https://lore.kernel.org/stable/2023081111-unlocking-synopsis-d7d5@gregkh/

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 64782497db)
2023-08-15 17:11:39 +02:00
Daniel Golle
b59d02becc generic: backport fix for Winbond SPI NAND
Avoid using stack allocated memory for DMA operations.

Fixes: 156c00dedc ("generic: backport Winbond W25N02KV SPI-NAND support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit e6f8b69918)
2023-08-13 17:49:40 +01:00
Daniel Golle
0ecf7a3791 generic: 5.15: rename patches to match correct version
Rename two patches which were only accepted in Linux 6.2, but were
marked as if they were accepted in Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 42e14d3ed8)
2023-08-13 16:30:14 +01:00
Daniel Golle
79d669d1b7 armsr: remove redundant phy-marvell-10g module
the Marvell 10G PHY driver is no way specific to ARM SystemReady
systems, it frequently occurs on SFP+ copper modules and is useful on
many targets.

Hence it been added to package/kernel/linux/modules/netdevices and we
can remove the now redundant target-specific module.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c524a76f4c)
2023-08-13 16:30:14 +01:00
Daniel Golle
452e4f064f mediatek: filogic: mt7988: mark RTC clock as critical
A dependency of the MT7988 MMC host controller on the SoC's RTC clock
being running has been discovered. Mark RTC clock as critical to fix
MMC host on MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0454691960)
2023-08-13 16:30:13 +01:00
Tomasz Maciej Nowak
57bf52c6e2 mvebu: mcbin-singleshot: enable hearbeat LED by default
This has been a part of modified upstream patch but got lost on major
kernel bump to 5.15, so bring it back.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Add patch for kernel 6.1 too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5e6bab661a)
2023-08-11 12:53:34 +02:00
Felix Baumann
ac34f6469e ath79: move ubnt-xm 64M RAM boards back to generic
return ubnt_rocket-m and ubnt_powerbridge-m back to ath79-generic
They have enough RAM-ressources to not be considered as tiny.

This reverts the commit f4415f7635 partially

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
(cherry picked from commit 9e86a96af5)
2023-08-11 12:53:34 +02:00
John Audia
ec0ff928d9 kernel: bump 5.15 to 5.15.125
1. Add new symbols to generic config
2. Bump kernel
   Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/

   All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
[Refreshed on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit daed3322d3)
2023-08-10 21:07:50 +02:00
John Audia
795a5dd452 kernel: bump 5.15 to 5.15.124
Changelog: https://lore.kernel.org/stable/2023080341-curliness-salary-4158@gregkh/

1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk
   due to upstream moving vxlan to its own directory[1].  @john-tho suggested
   using the the 6.1 xvlan FILES to circumvent.
2. All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=77396fa9096abdbfbb87d63e73ad44d5621cf103

Signed-off-by: John Audia <therealgraysky@proton.me>
[Refreshed on top of OpenWrt 23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 81c1172c36)
2023-08-10 21:06:55 +02:00
Pawel Dembicki
4ebba8a05d realtek: add support for HPE 1920-8g-poe+
Hardware information:
---------------------

- RTL8380 SoC
- 8 Gigabit RJ45 PoE ports (built-in RTL8218B)
- 2 SFP ports (built-in SerDes)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
- PoE chips: Nuvoton M0516LDE + BCM59121

Known issues:
---------------------
- PoE LEDs are uncontrolled.

(Manual taken from f2f09bc002)
Booting initramfs image:
------------------------

- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
  connect the server to a switch port.

- Connect to the console port of the device and enter the extended
  boot menu by typing Ctrl+B when prompted.

- Choose the menu option "<3> Enter Ethernet SubMenu".

- Set network parameters via the option "<5> Modify Ethernet Parameter".
  Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
  can be left blank, it is not required for booting from RAM). Note that
  the configuration is saved on flash, so it only needs to be done once.

- Select "<1> Download Application Program To SDRAM And Run".

Initial installation:
---------------------

- Boot an initramfs image as described above, then use sysupgrade to
  install OpenWrt permanently. After initial installation, the
  bootloader needs to be configured to load the correct image file

- Enter the extended boot menu again and choose "<4> File Control",
  then select "<2> Set Application File type".

- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
  use the option "<1> +Main" to select it as boot image.

- Choose "<0> Exit To Main Menu" and then "<1> Boot System".

NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).

Example PoE config file (/etc/config/poe):
---------------------
config global
        option budget   '180'

config port
        option enable   '1'
        option id       '1'
        option name     'lan8'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '2'
        option name     'lan7'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '3'
        option name     'lan6'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '4'
        option name     'lan5'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '5'
        option name     'lan4'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '6'
        option name     'lan3'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '7'
        option name     'lan2'
        option poe_plus '1'
        option priority '2'
config port
        option enable   '1'
        option id       '8'
        option name     'lan1'
        option poe_plus '1'
        option priority '2'

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit b370753fc4)
2023-08-09 22:14:12 +02:00
Daniel Golle
ad2fa6bc9c mediatek: filogic: restore non-const type in pinctrl-mt7988 driver
When building with Linux 5.15 the 'const' type results in warnings.
Restore the original non-const type in those cases.

Fixes: 36d0aa9c2d ("mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1eb67cb070)
2023-08-07 16:48:08 +01:00
Daniel Golle
c072069fa7 mediatek: filogic: update MT7988 device tree
* move ethernet to mt7988a.dtsi
 * move switch definition to mt7988a.dtsi
 * add PHY LEDs

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 64b99802a6)
2023-08-07 16:48:08 +01:00
Daniel Golle
830bb57f6a mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK
Update pinctrl driver for the MT7988 with driver from mtk-openwrt-feeds.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 36d0aa9c2d)
2023-08-07 16:48:07 +01:00
Daniel Golle
34cd471742 mediatek: filogic: enable driver for MediaTek XS-PHY
Enable driver for MediaTek SuperSpeedPlus XS-PHY transceiver for the
USB3.1 GEN2 controllers found in the MT7988 SoC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit dc4aafb309)
2023-08-07 16:48:07 +01:00
Petr Štetiar
5ae1b90e03 mediatek: filogic: fix broken sysupgrade script
Changes introduced in commit 54dc1cde48 ("mediatek: filogic: add
support for Xiaomi WR30U") missed to end the case item with mandatory
`;;` which lead to a broken sysupgrade.

Fixes: 54dc1cde48 ("mediatek: filogic: add support for Xiaomi WR30U")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-08-07 16:31:27 +01:00
Hank Moretti
34d8913bd5 mediatek: filogic: add specific layout for WR30U
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.

This layout is the same as the ubootmod layout but enabling NMBM.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-08-07 16:31:27 +01:00
Hank Moretti
0f0ea1087b mediatek: filogic: add support for Xiaomi WR30U
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: NT52B128M16JR-FL 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A

Flash instructions:

1. Get ssh access
   Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22

2. Backup import partitions
   ```
   dev:    size   erasesize  name
   mtd1: 00100000 00020000 "BL2"
   mtd2: 00040000 00020000 "Nvram"
   mtd3: 00040000 00020000 "Bdata"
   mtd4: 00200000 00020000 "Factory"
   mtd5: 00200000 00020000 "FIP"
   mtd8: 02200000 00020000 "ubi"
   mtd9: 02200000 00020000 "ubi1"
   mtd12: 00040000 00020000 "KF"

   ```

   Use these commands blow to backup your stock partitions.
   ```
   nanddump -f /tmp/BL2.bin /dev/mtd1
   nanddump -f /tmp/Nvram.bin /dev/mtd2
   nanddump -f /tmp/Bdata.bin /dev/mtd3
   nanddump -f /tmp/Factory.bin /dev/mtd4
   nanddump -f /tmp/FIP.bin /dev/mtd5
   nanddump -f /tmp/ubi.bin /dev/mtd8
   nanddump -f /tmp/KF.bin /dev/mtd12
   ```
   Then, transfer them to your computer via scp, netcat, tftp
   or others and keep them in a safe place.

3. Setup Nvram
   Get the current stock: `cat /proc/cmdline`

   If you find `firmware=0` or `mtd=ubi`, use these commands:
   ```
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=1
   nvram set flag_last_success=1
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   ```

   If you find `firmware=1` or `mtd=ubi1`, use these commands:
   ```
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=0
   nvram set flag_last_success=0
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   ```

4. Flash stock-initramfs-factory.ubi
   If you find `firmware=0` or `mtd=ubi`:
   `ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi`

   If you find `firmware=1` or `mtd=ubi1`:
   `ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi`

   Then reboot your router, it should boot to the openwrt
   initramfs system now.

5. Setup uboot-env
   Now it will be setup automatically in upgrade process,
   you can skip this step.

   If your `fw_setenv` did not work, you need run this command:
   `echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config`

   Then setup uboot-env:
   ```
   fw_setenv boot_wait on
   fw_setenv uart_en 1
   fw_setenv flag_boot_rootfs 0
   fw_setenv flag_last_success 1
   fw_setenv flag_boot_success 1
   fw_setenv flag_try_sys1_failed 8
   fw_setenv flag_try_sys2_failed 8
   fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),
   2048k(factory),2048k(fip),256k(crash),256k(crash_log),
   34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)"
   ```

6. Flash stock-squashfs-sysupgrade.bin
   Use shell command:
   `sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin`
   Or go to luci web.

If you need to change to Openwrt U-Boot layout, do next. If you
do not need, please ignore it.

Change to OpenWrt U-Boot:

1. Flash ubootmod-initramfs-factory.ubi
   Check mtd partitions: `cat /proc/mtd`
   ```
   mtd7: 00040000 00020000 "KF"
   mtd8: 02200000 00020000 "ubi_kernel"
   mtd9: 04e00000 00020000 "ubi"
   ```

   Run following command:
   `ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi`
   Then reboot your router, it should boot to the openwrt initramfs
   system now.

2. Check mtd again
   ```
   mtd7: 00040000 00020000 "KF"
   mtd8: 07000000 00020000 "ubi"
   ```
   Make sure mtd8 is ubi.

3. Install kmod-mtd-rw
   Run command: `opkg update && opkg install kmod-mtd-rw`
   Or get it in openwrt server, or build it yourself, then install
   it manually

   Then run this command:
   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Clean up pstore
   Run Command: `rm -f /sys/fs/pstore/*`

5. Format ubi and create new ubootenv volume
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
   ```

6. (Optional) Add recovery boot feature.
   ```
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
   ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb
   ```

7. Flash Openwrt U-Boot
   ```
   mtd write /tmp/ubootmod-preloader.bin BL2
   mtd write /tmp/ubootmod-bl31-uboot.fip FIP
   ```

6. Flash ubootmod-squashfs-sysupgrade.itb
   Use shell command:
   `sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb`
   Or go to luci web.

Now everything is done, Enjoy!

Go Back to stock from Openwrt U-Boot:

1. Force flash ubootmod-initramfs-recovery.itb
   Use shell command:
   `sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb`
   Or go to luci web.
   Then it should boot to the openwrt initramfs system now.

2. Format ubi and Nvram
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   mtd erase Nvram
   ```

3. Install kmod-mtd-rw
   Run command: `opkg update && opkg install kmod-mtd-rw`
   Or get it in openwrt server, or build it yourself, then install
   it manually

   Then run this command:
   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Flash stock U-Boot and ubi
   ```
   mtd write /tmp/BL2.bin BL2
   mtd write /tmp/FIP.bin FIP
   mtd write /tmp/ubi.bin ubi
   ```
   Then reboot your router, waiting it finished rollback in minutes.

Go Back to stock from stock layout Openwrt:
   Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin`
   Then reboot your router, waiting it finished rollback in minutes.

Notes:
1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM.
   Please make your backup safe.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-08-07 16:31:27 +01:00
David Bauer
c697057b7c mediatek: add support for Acer Predator W6
Hardware
--------
SOC:   MediaTek MT7986A
RAM:   1GB DDR4
FLASH: 4GB eMMC
WiFi:  2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC
       4x4 5 GHz   802.11 a/n/ac/ax MT7986
       2x2 6 GHz   802.11ax MT7916 DBDC
ETH:   4x LAN 1Gbit/s (MT7531)
       1x WAN 2.5Gbit/s (GPY211)
BTN:   RESET, WPS
LED:   Antenna LEDs (GPIO)
       Mood-LED (Kinetic KTD2601) - unsupported
UART:  Header nest to USB port - 3V3 115200 8N1
       [BUTTON] GND - RX - TX [USB]

Installation
------------

1. Connect to the device using serial console.

2. Interrupt the Autoboot process when promted by sending '0' twice.

3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name
   the image "predator.bin" and conenct the TFTP server to the routers
   LAN port.

4. Configure U-Boot to allow loading unsigned images from MMC

   $ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000;
     fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000';
     saveenv

5. Transfer the image from U-Boot

   $ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1;
     tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr);
     fdt rm /signature; bootm

6. Wait for OpenWrt to boot

7. Transfer the OpenWrt sysupgrade image to the router using scp.

8. Install OpenWrt using sysupgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 7e7eb5312d)
2023-08-05 18:49:34 +02:00
John Audia
7efec0acca kernel: bump 5.15 to 5.15.123
Manually rebased:
	bcm4908/patches-5.15/071-v6.1-0001-net-broadcom-bcm4908_enet-handle-EPROBE_DEFER-when-g.patch
	bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
	ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch[*]
	bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
	bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
	bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch

Removed upstreamed:
	backport-5.15/735-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1]
	backport-5.15/817-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[2]
	pending-5.15/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[3]
	pending-5.15/160-workqueue-fix-enum-type-for-gcc-13.patch[4]
	bcm53xx/patches-5.15/036-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[5]
	bcm53xx/patches-5.15/036-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[6]
	ipq807x/patches-5.15/0048-v6.1-clk-qcom-reset-Allow-specifying-custom-reset-delay.patch[7]
	ipq807x/patches-5.15/0049-v6.2-clk-qcom-reset-support-resetting-multiple-bits.patch[8]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=02474292a44205c1eb5a03634ead155a3c9134f4
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=86b93cbfe104e99fd3d25a49748b99fb88101573
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=79b9ab357b6f5675007f4c02ff8765cbd8dc06a2
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=d528faa9e828b9fc46dfb684a2a9fd8c2e860ed8
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=5899bc4058e89d5110a23797ff94439c53b77c25
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=95afd2c7c7d26087730dc938709e025a303e5499
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=40844343a8853a08b049d50c967e2a1e28f0ece6
8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=6ad5ded420f5d96f7c65b68135f5787a1c7e58d7

Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Audia <therealgraysky@proton.me>
[rebased ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch ]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8590531048)
[Refreshed on top of openwrt-23.05]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-07-31 01:39:50 +02:00
Rafał Miłecki
e0c4da1ff0 bcm53xx: backport more DT changes queued for v6.6
Those sort out BCM53573 Ethernet info finally.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit ca8868a511)
2023-07-29 19:43:44 +02:00
Rafał Miłecki
3bac348387 bcm53xx: add BCM53573 Ethernet fix sent upstream for v6.6
It seems that DSA-based b53 driver never worked with BCM53573 SoCs and
BCM53125.

In case of swconfig-based b53 this fixes a regression. Switching bgmac
from using mdiobus_register() to of_mdiobus_register() resulted in MDIO
device (BCM53125) having of_node set (see of_mdiobus_register_phy()).
That made downstream b53 driver read invalid data from DT and broke
Ethernet support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 79fd3e62b4)
2023-07-29 19:43:44 +02:00
Alexander Friese
680a4c7e12 ipq4019: fix support for AVM FRITZ!Repeater 3000
new versions of the device have NAND with 8bit ECC
which was not yet supported before. This change removes
ECC restrictions.

Signed-off-by: Alexander Friese <af944580@googlemail.com>
(cherry picked from commit 6b11f0ec83)
2023-07-27 13:54:55 +02:00
David Bauer
897d55bcdf ipq40xx: add support for Teltonika RUTX50
Hardware
--------
CPU:     Qualcomm IPQ4018
RAM:     256M
Flash:   16MB SPI-NOR (W25Q128)
         128MB SPI-NAND (XTX)
WiFi:    2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH:     4x LAN ; 1x WAN (Gigabit)
CELL:    Quectel RG501Q 3G/4G/5G

UART: Available on the goldfinger connector (Pinout silkscreened)
      115200 8N1 3V3 - Only connect RX / TX / GND

Installation
------------

1. Enable SSH in the Teltonika UI
   (System --> Administration --> Access Control)

2. Check from which partition set the device is currently running from.

   $ cat /proc/boot_info/rootfs/primaryboot

   In case this output reads 0, install a Software update from Teltonika
   first. After upgrade completion, check this file now reads 1 before
   continuing.

2. Transfer the OpenWrt factory image to the device using scp. Use the
   same password (user root!) as used for the Web-UI.

   $ scp -O openwrt-factory.bin root@192.168.1.1:/tmp

3. Connect to the device using ssh as the root user.

4. Install OpenWrt by writing the factory image to flash.

   $ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin

5. Instruct the bootloaer to boot from the first partition set.

   $ echo 0 > /proc/boot_info/rootfs/primaryboot
   $ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
   $ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
   $ mtd write /tmp/bootconfig.bin /dev/mtd2
   $ mtd write /tmp/bootconfig1.bin /dev/mtd3

6. Reboot the device.

   $ reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 844bb4bfad)
2023-07-26 15:37:56 +02:00
David Bauer
1face854a2 ipq40xx: move Teltonika RUT STM32 IO to specific DTS
Prepare to re-use the DTS for the RUTX50.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit dbc4be142e)
2023-07-26 15:37:56 +02:00
Mathew McBride
21f0ab503c kernel: move NXP DPAA2 SFP patches to generic patches
These are used by both the armsr (EFI boot) and
layerscape targets for phylink-controlled SFP
support on NXP DPAA2 platforms (LS1088,LS2088,LX2160).

This is in place of commit a7bd96c98f
("layerscape: add patches for SFP support on DPAA2 platforms")
in the main branch. armsr in main started at kernel 6.1
so there is not an equivalent 5.15 commit to cherry pick.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-07-26 13:36:58 +02:00
Mathew McBride
6a89cfa418 layerscape: base-files: remove redundant RAMFS_COPY_* additions
All the tools (e.g fw_setenv, ubiupdatevol) and config (fw_env.config)
needed for sysupgrade are already included in /lib/upgrade/stage2

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 094c37708a)
2023-07-26 13:36:58 +02:00
Mathew McBride
cef98caf6e layerscape: remove Traverse LS1043 boards
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.

Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).

It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit 8e7ba6fbae)
2023-07-26 13:36:58 +02:00
Mathew McBride
68a4c60b5c layerscape: armv8_64b: add Traverse Ten64 NAND variant
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.

See the online manual for more information, including the
flash layout[2].

This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.

We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
(cherry picked from commit af0546da34)
2023-07-26 13:36:58 +02:00
Shiji Yang
ead5860c56 ramips: do not print error log when mdio bus is disabled
The mdio bus is used to control externel switch. In most cases, they are
disabled, which is the normal behavior. Treating this as an error makes
no sense, so we need to change the notification level from error to info.

Fixes: a2acdf9607 ("ramips: mt7620: remove useless GMAC nodes")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 285f0668f4)
2023-07-26 13:28:37 +02:00
Shiji Yang
3ac300c753 ramips: backport upstream mt762x PCIe driver error log fixes
These patches silence some mt762x PCIe driver error messeges by removing
the useless debugging codes and replacing incorrectly used 'dev_err()'
with 'dev_info()':

PCI: mt7621: Use dev_info() to log PCIe card detection [1]
mips: pci-mt7620: do not print NFTS register value as error log [2]
mips: pci-mt7620: use dev_info() to log PCIe device detection result [3]

Patch [1] has already been merged into the Linux 6.3 branch. Patches [2] and
[3] have been merged into the "mips-next" tree, and they will be part of the
upcoming Linux 6.5.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v6.4-rc7&id=50233e105a0332ec0f3bc83180c416e6b200471e
[2] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=9f9a035e6156a57d9da062b26d2a48d031744a1e
[3] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=89ec9bbe60b61cc6ae3eddd6d4f43e128f8a88de

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 4e74777fa8)
2023-07-26 13:28:02 +02:00
Aleksander Jan Bajkowski
9d15baee6b lantiq: add patches headers
This commit adds headers to the patches, so they can be applied with the
git am command.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit 5d51079fd0)
2023-07-26 13:26:24 +02:00
Felix Baumann
65c1f418e3 kernel: update patches for mediatek filogic
Fix complaint from actions
Check Kernel patches (mediatek, filogic)
https://github.com/openwrt/openwrt/actions/runs/5569719763/job/15081672586?pr=13072

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
2023-07-26 13:19:49 +02:00
Felix Fietkau
339e71cbd3 kernel: drop mips highmem offset start overrides
The maximum offset that can be supported is 0x20000000
Do not override it to to something bigger than that on MT7621, as that could
cause issues based on the fixed memory mappings. This makes the last 64 MB
RAM unusable on MT7621 devices with 512 MB but avoids incurring a heavy
performance hit

Fixes: cd2b74e01e ("ramips: mt7621: disable highmem support and remove highmem offset patch")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a110de8152)
2023-07-24 20:19:11 +02:00
Felix Fietkau
e5dea9e37f ramips: mt7621: disable highmem support and remove highmem offset patch
On MT7621 it was observed, that enabling highmem support causes a significant
performance drop, as documented in: https://github.com/openwrt/openwrt/issues/13151
By adjusting the highmem start offset, we avoid leaving any RAM unaddressable,
even on devices with 512 MB

Fixes: https://github.com/openwrt/openwrt/issues/13151
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit cd2b74e01e)
2023-07-24 20:19:11 +02:00
David Bauer
476bf135fc mediatek: add support for ZyXEL NWA50AX Pro
Hardware
--------
CPU:    Mediatek MT7981
RAM:    512M DDR4
FLASH:  256M NAND
ETH:    MaxLinear GPY211 (2.5GbE N Base-T)
WiFi:   Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN:    1x Reset
LED:    1x Multi-Color

UART Console
------------
Available below the rubber cover next to the ethernet port.

Settings: 115200 8N1

Layout:

<12V> <LAN> GND-RX-TX-VCC

Logic-Level is 3V3. Don't connect VCC to your UART adapter!

Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.

As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.

In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.

If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.

Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.

Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.

The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.

Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.

 $ atnf nwa50axpro-openwrt-initramfs.bin
 $ atna 192.168.1.88
 $ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
   bootm"

Upon booting, set the booted image to the correct slot:

 $ zyxel-bootconfig /dev/mtd9 get-status
 $ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
 $ zyxel-bootconfig /dev/mtd9 set-active-image 0

Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.

 $ sysupgrade -n image.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f0445746f6)
2023-07-23 16:10:08 +02:00
Daniel Golle
b28d74090f mediatek: filogic: set DEVICE_DTS_LOADADDR for BPi-R3
U-Boot complains that the overlayed DT needs relocation, so set
DEVICE_DTS_LOADADDR to have it relocated.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit b1d10e0174)
2023-07-22 18:54:03 +01:00
Carsten Spieß
345bce75a1 octeon: ubnt-edgerouter-4/6p: devicetree cleanup
removed redundant eeprom partition nodes from
cn7130_ubnt_edgerouter-4.dts and cn7130_ubnt_edgerouter-6p.dts
as they are identically defined in cn7130_ubnt_edgerouter-e300.dtsi.

Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(integrated eeprom referenced node in the .dtsi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 700f11aaad)
2023-07-15 22:24:50 +02:00
Carsten Spieß
abe659efba octeon: ubnt-edgerouter-e300: fix missing MTD partition
The MAC addresses should be read from 3rd MTD partition,
but only two MTD partitions are populated.

To fix it, a partitions node has to surround the partition
nodes in device tree.

Tested with Edgerouter 6P

Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(fixed checkpatch complains)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 2b1d7965c7)
2023-07-15 22:24:50 +02:00
Carsten Spieß
00d4a3190b octeon: ubnt-edgerouter-e300: fix LED settings
LEDs on Edgerouter 6P didn't work correctly:
blue /white LED swapped, on/off state inverted

Fixed in device tree:
swap the GPIO ports for power:blue and power:white LEDs
change LED activity from LOW to HIGH

Tested on Edgerouter 6P

Signed-off-by: Carsten Spieß <mail@carsten-spiess.de>
(cherry picked from commit 9009672930)
2023-07-15 22:24:50 +02:00
Christian Lamparter
62496e9a1a armsr: v8: fix NVMEM_IMX_OCOTP_ELE build error
there's a new symbol NVMEM_IMX_OCOTP_ELE that needs to be defined.
otherwise the build will fail:

|  i.MX On-Chip OTP Controller support (NVMEM_IMX_OCOTP_ELE) [N/m/y/?] (NEW)
| make[6]: *** [scripts/kconfig/Makefile:77: syncconfig] Error 1
| make[5]: *** [Makefile:628: syncconfig] Error 2

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-07-15 22:17:42 +02:00
Rafał Miłecki
b32a4bc33f bcm53xx: backport DT changes queued for v6.6
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 37ff916af7)
2023-07-14 13:53:31 +02:00
Daniel Golle
40a26239ff mediatek: replace hack for MaxLinear 2.5G PHY
Replace hack with proper patch also for Linux 5.15.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 712fa3eff8)
2023-07-13 12:05:28 +01:00
Daniel Golle
f94cda0187 mediatek: dts: mt7988a: remove boottrap hack
The PHY driver now uses regmap created from pio syscon, we no longer
need the boottrap device.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f321a49fd5)
2023-07-13 12:05:28 +01:00
Daniel Golle
6092c39c13 mediatek: use backported Ethernet PHY driver also for 5.15
Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the
driver in files-5.15.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9fac590096)
2023-07-13 12:05:28 +01:00
Daniel Golle
0af05cd32a mediatek: dts: mt7988a: wire-up mediatek,pio for PHY LEDs
The PHY driver needs to read a register containing the values of the
bootstrap pins (which happen to be the PHY LEDs) to determine the LED
polarities. Allow regmap access to first pinctrl bank by adding the
'syscon' compatible, and reference the pinctrl in the MDIO bus where
the PHY driver will look for it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1f1e0b1144)
2023-07-13 12:05:28 +01:00
Chukun Pan
cf81850cce mediatek: filogic: add H3C Magic NX30 Pro support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: W25N01GVZEIG 128MB
  RAM: NT5CB128M16JR-FL 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, WPS
  Power: DC 12V 1A

Flash instructions:
  1. PC run command: "telnet 192.168.124.1 99"
     Username: H3C, password is the web login
     password of the router.
  2. Download preloader.bin and bl31-uboot.fip
  3. PC run command: "python3 -m http.server 80"
  4. Download files in the telnet window:
     "wget http://192.168.124.xx/xxx.bin"
     Replace xx with your PC's IP and
     the preloader.bin and bl31-uboot.fip.
  5. Flushing openwrt's uboot:
     "mtd write xxx-preloader.bin BL2"
     "mtd write xxx-bl31-uboot.fip FIP"
  6. Connect to the router via the Lan port,
     set a static ip of your PC.
     (ip 192.168.1.254, gateway 192.168.1.1)
  7. Download initramfs image, reboot router,
     waiting for tftp recovery to complete.
  8. After openwrt boots up, perform sysupgrade.

Note:
  1. The u-boot-env partition on mtd is empty,
     OEM stores their env on ubi:u-boot-env.
  2. Back up all mtd partitions before flashing.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit e78d1a06c8)
2023-07-13 12:05:28 +01:00
Wenli Looi
23d6474e45 mediatek: add support for Netgear EX6250v2 series
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.

Related: https://github.com/openwrt/openwrt/pull/5084

For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.

Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
  boot, then hold the reset button for 10 seconds. This is needed
  because sysupgrade in the stock firmware will attempt to preserve its
  configuration using sysupgrade.tgz.
  See https://github.com/openwrt/openwrt/pull/4182

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 73de41898f)
2023-07-13 12:05:28 +01:00
Wenli Looi
977ee439d7 image: add additional fields to Netgear encrypted image
These fields are used for EAX12 and EX6250v2 series, and perhaps other
devices. Compatibility is preserved with the WAX202 and WAX206.

In addition, adds the related vars to DEVICE_VARS so that the variables
work correctly with multiple devices.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* tools/imgencoder/src/gj_enc.c
  Contains code that generates the encrypted image.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
(cherry picked from commit 0a1ebccc87)
2023-07-13 12:05:28 +01:00
Pavel Pernička
b7fac1bf8c ath79: DTS improvement for buzzer on RB951G-2HnD
Mikrotik RB951 router has a buzzer on the board, which makes annoying noises
due to the interference caused by PoE input or Wifi transmission
when no GPIO pin state is set.
I added buzzer node to device's DTS in order to set deault level to 1
and to provide easier access for it.

Signed-off-by: Pavel Pernička <pernicka.pa@gmail.com>
(cherry picked from commit dac0a133cf)
2023-07-12 20:46:53 +02:00
Michał Kępień
98b397d4fb ath79: add support for MikroTik RB951G-2HnD
MikroTik RB951G-2HnD is a wireless SOHO router that was previously
supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add
kernel support for the Mikrotik RB951G board").

Specifications
--------------

  - SoC: Atheros AR9344 (600 MHz)
  - RAM: 128 MB (2x 64 MB)
  - Storage: 128 MB NAND flash (various manufacturers)
  - Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s
      - 1x PoE in (port 1, 8-30 V input)
  - Wireless: Atheros AR9340 (802.11b/g/n)
  - USB: 2.0 (1A)
  - 8x LED:
      - 1x power (green, not configurable)
      - 1x user (green, not configurable)
      - 5x GE ports (green, not configurable)
      - 1x wireless (green, not configurable)
  - 1x button (restart)

Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be
GPIO-controllable, which was also the case for older OpenWRT versions
that supported this board via a mach file.  The Ethernet port LEDs are
controlled by the switch chip.

See https://mikrotik.com/product/RB951G-2HnD for more details.

Flashing
--------

TFTP boot initramfs image and then perform sysupgrade.  Follow
common MikroTik procedures at https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
(cherry picked from commit db02cecd6a)
2023-07-12 20:45:43 +02:00
Michał Kępień
7bb616d300 ath79: mikrotik: extract common bits for RB951x-2HnD devices
Mikrotik RouterBOARD 951Ui-2HnD and Mikrotik RouterBOARD RB951G-2HnD are
very similar devices.  Extract the DTS bits that are identical for these
two boards to a separate DTSI file.

Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
(cherry picked from commit c6ef417094)
2023-07-12 20:45:43 +02:00
Rafał Miłecki
a4792d79e8 bcm53xx: backport DT changes from v6.5
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8674b41c0d)
2023-07-11 10:53:45 +02:00
Rafał Miłecki
a210fced85 kernel: bgmac: fix regressed support for BCM53573 SoCs
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit d54f3b2cfd)
2023-07-10 12:54:53 +02:00
Rafał Miłecki
e341d51e06 bcm47xx: fix bgmac MTU patch filename
Fixes: 4970dd027b ("bcm47xx: revert bgmac back to the old limited max frame size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 83aeb0bbd4)
2023-07-10 12:54:53 +02:00
Rafał Miłecki
ef7d800333 kernel: backport NVMEM patches queued for the v6.5
This includes some driver changes and support for fixed cells layout.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 07bdc55515)
2023-07-10 12:54:53 +02:00
Martin Schiller
f4e1f99961 kernel: net: phy: realtek: fix rtl822x_probe on unsupported devices
Calling rtl822x_probe() on phy devices which uses the rtl822x_read_mmd()
and rtl822x_write_mmd() functions makes no sense and the probe ends with
an EOPNOTSUPP error.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit 5af7d47cd7)
2023-07-08 15:48:28 +02:00
Felix Fietkau
c49654f4f0 ramips/mt7621: disable the cpufreq driver
It causes a noticeable performance decrease

Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit dc38199b96)
2023-07-08 15:46:54 +02:00
Aleksander Jan Bajkowski
ac2d6cf573 kernel: sort generic configuration
This was done by executing these commands:

$ ./scripts/kconfig.pl '+' target/linux/generic/config-5.15 /dev/null > target/linux/generic/config-5.15-new
$ mv target/linux/generic/config-5.15-new target/linux/generic/config-5.15

$ ./scripts/kconfig.pl '+' target/linux/generic/config-6.1 /dev/null > target/linux/generic/config-6.1-new
$ mv target/linux/generic/config-6.1-new target/linux/generic/config-6.1

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit 4f197f9134)
2023-07-08 15:45:12 +02:00
John Audia
5678bb801e kernel: bump 5.15 to 5.15.120
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 0dc0504fc8)
2023-07-08 15:43:59 +02:00
John Audia
e4d7917be6 x86: set CONFIG_X86_AMD_PLATFORM_DEVICE
Needed by AMD processors using Carrizo and later chipsets

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 946100ba41)
2023-07-08 15:43:59 +02:00
Zoltan HERPAI
4a79a94e37 mxs: rework image generation
Migrate to "new" image generation method. Device profiles will be generated
based on image/Makefile instead of profiles/ , which will also allow to
automatically build images for all supported devices via buildbot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-07-06 17:04:13 +02:00
Christian Lamparter
894b2086fd ipq-wifi: fix upstream board-2.bin ZTE M289F snafu
The upstream board-2.bin file in the linux-firmware.git
repository for the QCA4019 contains a packed board-2.bin
for this device for both 2.4G and 5G wifis. This isn't
something that the ath10k driver supports.

Until this feature either gets implemented - which is
very unlikely -, or the upstream boardfile is mended
(both, the original submitter and ath10k-firmware
custodian have been notified). OpenWrt will go back
and use its own bespoke boardfile. This unfortunately
means that 2.4G and on some revisions the 5G WiFi is
not available in the initramfs image for this device.

Fixes: #12886
Reported-by: Christian Heuff <christian@heuff.at>
Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 75505c5ec7)
2023-07-04 22:11:08 +02:00
Sander Vanheule
cd878b1b55 ramips: mt7621: add TP-Link EAP613 v1
The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can
be powered via PoE or a DC barrel connector (12V). Connecting to the
UART requires fine soldering and careful manipulation of any soldered
wires.

Device details:
  * SoC: MT7621AT
  * Flash: 16 MiB SPI NOR
  * RAM: 256 MiB DDR3L
  * Wi-Fi:
    * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2
    * Two stamped metal antennas (ANT1, ANT2)
    * One PCB antenna (ANT3)
    * One unpopulated antenna (ANT4)
  * Ethernet:
    * 1× 10/100/1000 Mbps port with PoE
  * LEDs:
    * Array of four blue LEDs with one control line
  * Buttons:
    * Reset
  * Board test points:
    * UART: next to CPU RF-shield and power circuits
    * JTAG: under CPU RF-shield (untested)
  * Watchdog: 3PEAK TPV706 (not implemented)

  Althought three antennas are populated, the MT7905DA does not support
  the additional Rx chain for background DFS detection (or Bluetooth)
  according to commit 6cbcc34f50 ("ramips: disable unsupported
  background radar detection").

MAC addresses:
  * LAN: 48:22:54:xx:xx:a2 (device label)
  * WLAN 2.4 GHz: 48:22:54:xx:xx:a2
  * WLAN 5 GHz: 48:22:54:xx:xx:a3

  The radio calibration blob stored in flash also contains valid MAC
  addresses for both radio bands (OUI 00:0c:43).

Factory install:
  1. Enable SSH on the device via web interface
  2. Log in with SSH, and run `cliclientd stopcs`
  3. Upload -factory.bin image via web interface. It may be necessary to
     shorten the filename of the image to e.g. 'factory.bin'.

Recovery:
  1. Open the device by unscrewing four screws from the backside
  2. Carefully remove board from the housing
  3. Connect to UART (3.3V):
    * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX"
    * Solder wires to test points or connect otherwise. Be careful not
      to damage the PCB e.g. by pulling on soldered wires.
    * Open console with 115200n8 settings
  4. Interrupt bootloader and use tftpboot to start an initramfs:
        setenv ipaddr $DEVICE_IP
        setenv serverip $SERVER_IP
        tftpboot 84000000 openwrt-initramfs-kernel.bin
        bootm

  DO NOT use saveenv to store modified u-boot environment variables. The
  environment is saved at flash offset 0x30000, which erases part of the
  (secondary) bootloader.

  The device uses two bootloader stages. The first stage will load the
  second stage from a uImage stored at flash offset 0x10000. In case of
  a damaged second stage, the first stage should allow uploading a new
  image via y-modem (untested).

Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 11588c52b4)
2023-07-03 21:07:33 +02:00
David Bauer
fa1822a8e9 mediatek: define NMBM management region for WAX220
The NETGEAR WAX220 employs NMBM on SPI-NAND. In order to avoid dealing
with invalid factory data, enable NMBM in the area preceding the UBI
volume.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 92eec257dd)
2023-07-02 15:31:03 +02:00
Robert Marko
0d324c682c generic: filter out CONFIG_FRAME_WARN
CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the
target type dynamically since commit:
16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target").

However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up
in multiple target configs during refreshes.
So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it
ending up in more target configs.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 7a9a4168bb)
2023-07-02 15:31:03 +02:00
Joshua O'Leary
fbb4aac69b zbt-wd323: add GPIO WDT support
Watchdog has not been properly configured for this router - the PCB has a
hardware watchdog connected to one of the GPIO pin 21 [1]
This commit provides this fix [2]

Without this fix, the ZBT-WD323 is unusable in OpenWRT because it power
cycles every 30 seconds due to the watchdog tripping

[1] https://forum.openwrt.org/t/zbt-wd323-router-power-cycles-every-30-seconds/77535/7
[2] https://forum.openwrt.org/t/zbt-wd323-images-unusable-proposed-workaround/162145/5

Signed-off-by: Joshua O'Leary <josh.oleary@mobile-power.co.uk>
(cherry picked from commit 008cc836fe)
2023-07-02 15:31:03 +02:00
Mikhail Zhilkin
436ef37728 ramips: add support for Sercomm S1500 devices
This commit adds support for following wireless routers:
 - Beeline SmartBox PRO (Serсomm S1500 AWI)
 - WiFire S1500.NBN (Serсomm S1500 BUC)

This commit is based on this PR:
 - Link: https://github.com/openwrt/openwrt/pull/4770
 - Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.

My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1

Common specification
--------------------
SoC:        MediaTek MT7621AT (880 MHz, 2 cores)
Switch:     MediaTek MT7530 (via SoC MT7621AT)
Wireless:   2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless:   5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet:   5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe:  via J2 on PCB, not soldered on the board
UART:       J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek

Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1

WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1

MAC address table (PRO)
-----------------------
use   address   source
LAN   *:23      factory 0x1000 (label)
WAN   *:24      factory $label +1
2g    *:23      factory $label
5g    *:25      factory $label +2

MAC addresses (NBN)
-------------------
use   address   source
LAN   *:0e      factory 0x1000
WAN   *:0f      LAN +1 (label)
2g    *:0f      LAN +1
5g    *:10      LAN +2

OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
   before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
   a. OpenWrt - that's OK, the mission accomplished
   b. Stock firmware - install Stock firmware (to switch booflag from
      Sercomm0 to Sercomm1) and then OpenWrt factory image.

Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
   reboot
2. Install stock firmware via the web OEM firmware interface

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 2d6784a033)
2023-07-02 15:19:34 +02:00
Mikhail Zhilkin
5399d0362f ramips: sercomm.mk: preparation for Sercomm s1500 devices support
This commit moves a part of the code from the "sercomm-factory-cqr" recipe
to the separate "sercomm-mkhash" recipe. This simplifies recipes and
allows insert additional recipes between these code blocks (required for
the future support for Beeline SmartBox PRO router).

dd automatically fills the file by 0x00 if the filesize is less than
offset where we start writing. We drop such dd command so we need to add
--extra-padding-size 0x190 to the sercomm-pid.py call.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit f560be583a)
2023-07-02 15:19:34 +02:00
John Audia
c719dfd29f kernel: bump 5.15 to 5.15.119
Build system: x86_64
Build-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3
Run-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 42cb0f0f26)
2023-07-02 10:59:25 +02:00
Mikhail Zhilkin
7ff95775a2 mediatek: add support for Mercusys MR90X v1
This commit adds support for Mercusys MR90X(EU) v1 router.

Device specification
--------------------
SoC Type:   MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM:        MediaTek MT7986BLA (512MB)
Flash:      SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet:   MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet:   1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g:    MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g:    MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs:       1 orange and 1 green status LEDs, 4 green gpio-controlled
            LEDs on ethernet ports
Button:     1 (Reset)
USB ports:  No
Power:      12 VDC, 2 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
            slots contain "seconduboot" (also U-Boot 2022.01-rc4)

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |
    +--- Don't connect

The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.

Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Once inside OpenWrt, set / update env variables:
      fw_setenv baudrate 115200
      fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
      fw_setenv fdtcontroladdr 5ffc0e70
      fw_setenv ipaddr 192.168.1.1
      fw_setenv loadaddr 0x46000000
      fw_setenv mtdids "spi-nand0=spi-nand0"
      fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
      fw_setenv netmask 255.255.255.0
      fw_setenv serverip 192.168.1.2
      fw_setenv stderr serial@11002000
      fw_setenv stdin serial@11002000
      fw_setenv stdout serial@11002000
      fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Installation (without UART)
---------------------------
1.  Login as root via SSH (router IP, port 20001, password - your web
    interface password)
2.  Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
    SSH settings from the p.1)
3.  Add a newline after "#!/bin/sh":
       telnetd -l /bin/login.sh
4.  Save "65-iptv" file
5.  Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
    save
6.  Make sure that telnetd is running:
       netstat -ltunp | grep 23
7.  Login via telnet to router IP, port 23 (no username and password are
    required)
8  Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
    router (e.g., using WinSCP and SSH settings from the p.1)
9.  Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
    download and upload the full version of busybox to the router. For
    example, from here:
    https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
    Upload busybox-arm64 to the /tmp dir of the router and run:
    in the telnet shell:
       cd /tmp
       chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
       du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
    (greater than "initramfs-kernel.bin" size):
       ubirmvol /dev/ubi0 -N kernel
       ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
       ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
    already exists) with the necessary values:
       fw_setenv baudrate 115200
       fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
       fw_setenv fdtcontroladdr 5ffc0e70
       fw_setenv ipaddr 192.168.1.1
       fw_setenv loadaddr 0x46000000
       fw_setenv mtdids "spi-nand0=spi-nand0"
       fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
       fw_setenv netmask 255.255.255.0
       fw_setenv serverip 192.168.1.2
       fw_setenv stderr serial@11002000
       fw_setenv stdin serial@11002000
       fw_setenv stdout serial@11002000
       fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
       reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
       sysupgrade -n /tmp/sysupgrade.bin

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
   upload the OEM firmware

Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
   etc.)

Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"

ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot   Vol ID: 0|
| Volume Name: kernel  Vol ID: 1|
| Volume Name: rootfs  Vol ID: 2|
+-------------------------------+

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| label   | 00:eb:xx:xx:xx:be | label     |
| LAN     | 00:eb:xx:xx:xx:be | label     |
| WAN     | 00:eb:xx:xx:xx:bf | label+1   |
| WLAN 2g | 00:eb:xx:xx:xx:be | label     |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1   |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit e4fe3097ef)
[Fix merging conflict]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-07-01 15:16:17 +00:00
Andreas Böhler
023a8853c8 ipq4019: add support for ZTE MF287+ aka DreiNeo
The ZTE MF287+ is a LTE router used (exclusively?) by the network operator
"3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only
difference is the LTE modem)

Specifications
==============

SoC: IPQ4018
RAM: 256MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 4x GBit LAN
LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287)
WiFi: 802.11a/b/g/n/ac SoC-integrated

MAC addresses
=============

LAN: from config + 2
WiFi 1: from config
WiFi 2: from config + 1

Installation
============

Option 1 - TFTP
---------------

TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:

  setenv serverip 192.168.1.100
  setenv ipaddr 192.168.1.1
  tftpboot 0x82000000 openwrt.bin
  bootm 0x82000000

From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download:

  ubiattach -m14
  cat /dev/ubi0_0 > /tmp/ubi0_0
  cat /dev/ubi0_1 > /tmp/ubi0_1

Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save.

Once booted, transfer the sysupgrade image and run sysupgrade. You might
have to delete the stock volumes first:

  ubirmvol /dev/ubi0 -N ubi_rootfs
  ubirmvol /dev/ubi0 -N kernel

Option 2 - From stock firmware
------------------------------

The installation from stock requires an exploit first. The exploit consists
of a backup file that forces the firmware to download telnetd via TFTP from
192.168.0.22 and run it. Once exploited, you can connect via telnet and
login as admin:admin.

The exploit will be available at the device wiki page.

Once inside the stock firmware, you can transfer the -factory.bin file to
/tmp by using "scp" from the stock frmware or "tftp".

ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write
access - you need to read from one file in /proc. Once done, you need to
erase the UBI partition and flash OpenWrt. Before performing the operation,
make sure that mtd13 is the partition labelled "rootfs" by calling
"cat /proc/mtd".

Complete commands:

  cd /tmp
  tftp -g -r factory.bin 192.168.0.22
  cat /proc/driver/sensor_id
  flash_erase /dev/mtd13 0 0
  dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072

Afterwards, reboot your device and you should have a working OpenWrt
installation.

Restore Stock
=============

Option 1 - via UART
-------------------

Boot an OpenWrt initramfs image via TFTP as for the initial installation.
Transfer the two backed-up files to your box to /tmp.

Then, run the following commands - replace $kernel_length and $rootfs_size
by the size of ubi0_0 and ubi0_1 in bytes.

  ubiattach -m 14
  ubirmvol /dev/ubi0 -N kernel
  ubirmvol /dev/ubi0 -N rootfs
  ubirmvol /dev/ubi0 -N rootfs_data
  ubimkvol /dev/ubi0 -N kernel -s $kernel_length
  ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size
  ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0
  ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1

Option 2 - from within OpenWrt
------------------------------

This option requires to flash an initramfs version first so that access
to the flash is possible. This can be achieved by sysupgrading to the
recovery.bin version and rebooting. Once rebooted, you are again in a
default OpenWrt installation, but no partition is mounted.

Follow the commands from Option 1 to flash back to stock.

LTE Modem
=========

The LTE modem is similar to other ZTE devices and controls some more LEDs
and battery management.

Configuring the connection using uqmi works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit f70ee53b08)
2023-07-01 15:31:56 +02:00
Andreas Böhler
a9c92b913a ipq40xx: Enable gpio-restart in kernel configuration
Some ZTE devices require the gpio-restart driver to support restarting the
LTE modem along with OpenWrt

Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 9ffdaa7fa1)
2023-07-01 15:31:56 +02:00
Flole Systems
cd17d8df2a
filogic: add support for Netgear WAX220
Hardware
--------
SOC:   MediaTek MT7986
RAM:   1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI:  Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH:   Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART:  3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)

Installation
------------

1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
   interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.

   $ setenv ipaddr 192.168.2.1
   $ setenv serverip 192.168.2.2
   $ tftpboot openwrt.bin
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit 984786a2f7)
2023-06-26 13:20:39 +02:00
John Audia
51c397c33f kernel: bump 5.15 to 5.15.118
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 1f5fce27c1)
2023-06-25 16:05:18 +02:00
Lech Perczak
b1b829ad6a ipq40xx: meraki-mr33, meraki-mr74: disable image generation
After migrating to kernel 5.15, upgrading causes the units to become
soft-bricked, hanging forever at the kernel startup.
Kernel size limitation of 4000000 bytes is suspected here, but this is
not fully confirmed.

Disable the images to protect users from inadvertent bricking of units,
because recovery of those is painful with Cisco's U-boot, until the root
cause is found and fixed.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 9d64cc068f)
2023-06-25 12:34:47 +02:00
Davide Fioravanti
fca03ea458 ramips: fix lan leds for Wavlink WL-WN535K1
Previously both lan1 and lan2 leds were wrongly labelled as lan2.
Moreover they were connected to the wrong lan port.
Fixes 8fde82095b ("ramips: add support for Wavlink WL-WN535K1")

Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com>
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit c71dada926)
2023-06-25 12:34:47 +02:00
Kim DoHyoung
0a63e72fbb ramips: mt7621: add support for Zbtlink ZBT-WG1608 (32M)
Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G)
modems.

Specifications:
* SoC: MediaTek MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB (SPI NOR)
* Wi-Fi:
  * MediaTek MT7603E : 2.4Ghz
  * MediaTek MT7613BE : 5Ghz
* Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* M.2: 1x slot with USB&SIM
  * EM7455/EM12-G/EM160R/RM500Q-AE
* USB: 1x 3.0 Type-A port
* External storage: 1x microSD (SDXC) slot
* UART: console (115200 baud)
* LED:
  * 1 power indicator
  * 1 WLAN 2.4G controlled (wlan 2G)
  * 3 SoC controlled (wlan 5G, wwan, internet)
  * 5 per Eth phy (4xLAN + WAN)

MAC Addresses:
* LAN    : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex))
* WAN    : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex))
* 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex))
* 5 GHz  : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex))

Installation:
* Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can
  be directly used to install OpenWrt. Firmware must be upgraded using the
  'force' and 'do not save configuration' command line options (or
  correspondig web interface checkboxes) since the vendor firmware is from
  the pre-DSA era.

Recovery Mode:
 * Press reset button, power up the device, wait for about 10sec.
 * Upload sysupgrade image through the firmware recovery mode web page at
  192.168.1.1.

Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr>
(cherry picked from commit 0bbd5699c8)
2023-06-25 12:32:50 +02:00
David Bauer
b6f2c58dd6 ath79: add support for Aruba AP-115
Hardware
========

CPU   Qualcomm Atheros QCA9558
RAM   256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI  Qualcomm Atheros QCA9558
      Atheros AR9590

Installation
============

1. Attach to the serial console of the AP-105.
   Interrupt autoboot and change the U-Boot env.

   $ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
     setenv serverip 192.168.1.66;
     netget 0x80060000 ap115.bin; go 0x80060000"
   $ setenv fb_openwrt "bank 1;
     cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
   $ setenv bootcmd "run fb_openwrt"
   $ saveenv

2. Load the OpenWrt initramfs image on the device using TFTP.
   Place the initramfs image as "ap105.bin" in the TFTP server
   root directory, connect it to the AP and make the server reachable
   at 192.168.1.66/24.

   $ run rb_openwrt

3. Once OpenWrt booted, transfer the sysupgrade image to the device
   using scp and use sysupgrade to install the firmware.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1b467a902e)
2023-06-23 00:23:48 +02:00
Daniel González Cabanelas
aa256ab580 bmips: add support for Arcadyan AR7516
The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi
fast ethernet router, 2.4 GHz single band with two internal antennas. It
comes with a horizontal stand black shiny casing.

Newer Bright Box 1 model stands vertically, and comes with a totally
different board inside, not compatible with this firmware.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 V7.5 @ 320Mhz
 - RAM: 64 MB DDR2
 - Flash: 8 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: Broadcom BCM43227 802.11bgn (onboard)
 - USB: 1x 2.0
 - ADSL: yes, unsupported
 - Buttons: 2x
 - LEDs: 9x, power LED is hardware controlled
 - UART: yes

Installation in two steps, new CFE bootloader and firmware:

Install new CFE:
  1. Power off the router and press the RESET button
  2. Power on the router and wait some seconds
  3. Release the RESET button
  3. Browse to http://192.168.1.1, this web interface will offer both
     firmware (“Software”) upgrade and bootloader upgrade; be sure to
     use the bootloader section of the upload form.
  4. Upload the new CFE (availabe at the wiki page)
  5. Wait about a minute for flashing to finish and reboot into the new bootloader.

Install OpenWrt via new CFE web UI:
  1. After installing the new CFE, visit http://192.168.1.1
  2. Upload the Openwrt cfe firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry-picked from df8e4b6c2e)
2023-06-22 17:55:04 +02:00
Etienne Champetier
09322f3c0c
kernel: remove bridge offload hack
This patch initially introduced in 94b4da9b4a
breaks mvebu devices when using vlan filtering with kernel 5.15 or 6.1,
it was working ok in 5.10.

With this patch, frame that should exit untagged from the switch exit tagged.
Running 'tcpdump -Q out -evnnli eth1' (eth1 being the dsa interface)
- with the hack, frame is sent directly to the
destination port 4 with VID 2, so the switch leave the tag as instructed:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode From CPU, target dev 0, port 4, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28

- without the hack, frame is sent to the switch that
performs the forwarding decision and untagging:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode Forward, dev 1, port 0, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28

Removing this patch makes my Turris Omnia usable with vlan filtering,
ie wifi device can talk to wired device again.
Using kernel 5.15 some broadcast/multicast traffic is still leaked
(on a VLAN 2 access port I see tagged VLAN 3 frame),
using kernel 6.1 fixes that.

People needing the extra performance should try the bridger package.

Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 244328b19c)
2023-06-20 10:55:43 +02:00
Daniel González Cabanelas
ac6832110a bmips: add support for NuCom R5010UNv2
The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 V7.5 @ 320Mhz
 - RAM: 64 MB DDR2
 - Flash: 16 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard)
 - USB: 1x 2.0
 - Buttons: 2x
 - ADSL: yes, unsupported
 - LEDs: 7x
 - UART: yes

Installation via CFE web UI:
  1. Power off the router and press the RESET button
  2. Power on the router and wait 12 or more seconds
  3. Release the RESET button
  4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 6cb3328b4f)
2023-06-19 20:42:44 +02:00
Daniel González Cabanelas
43746c4c5a bmips: enable the data Read Ahead Cache for BMIPS4350
The data RAC is left disabled by the bootloader in some SoCs, at least in
the core it boots from. Enabling this feature increases the performance up
to +30% depending on the task.

The kernel enables the whole RAC unconditionally on BMIPS3300 CPUs. Enable
the data RAC in a similar way also for BMIPS4350.

Tested on DGND3700 v1 (BCM6368) and HG556a (BCM6358).

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 6d1265b148)
2023-06-19 20:42:19 +02:00
Álvaro Fernández Rojas
6d3770501d bmips: fix DMA RAC flush
BMIPS_GET_CBR() returns an invalid address on some SoCs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 62cdca25ed)
2023-06-19 20:41:57 +02:00
Maximilian Weinmann
8a0746955d ramips: Add support for Beeline SmartBox TURBO+
This adds support for Beeline Smart Box TURBO+ (Serсomm S3 CQR) router.

Device specification
--------------------
SoC Type: MediaTek MT7621AT (880 MHz, 2 cores)
RAM (Nanya NT5CC64M16GP): 128 MiB
Flash (Macronix MX30LF1G18AC): 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615N): a/n/ac, 4x4
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
USB ports: 1xUSB3.0
Buttons: 2 button (reset, wps)
LEDs: Red, Green, Blue
Zigbee (EFR32MG1B232GG): 3.0
Stock bootloader: U-Boot 1.1.3
Power: 12 VDC, 1.5 A

Installation (fw 2.0.9)
-----------------------
1.  Login to the web interface under SuperUser (root) credentials.
    Password: SDXXXXXXXXXX, where SDXXXXXXXXXX is serial number of the
    device written on the backplate stick.
2.  Navigate to Setting -> WAN. Add:
       Name - WAN1
       Connection Type - Static
       IP Address - 172.16.0.1
       Netmask - 255.255.255.0
    Save -> Apply. Set default: WAN1
3.  Enable SSH and HTTP on WAN. Setting -> Remote control. Add:
       Protocol - SSH
       Port - 22
       IP Address - 172.16.0.1
       Netmask - 255.255.255.0
       WAN Interface - WAN1
    Save ->Apply
    Add:
       Protocol - HTTP
       Port - 80
       IP Address - 172.16.0.1
       Netmask - 255.255.255.0
       WAN interface - WAN1
    Save -> Apply
4.  Set up your PC ethernet:
       Connection Type - Static
       IP Address - 172.16.0.2
       Netmask - 255.255.255.0
       Gateway - 172.16.0.1
5.  Connect PC using ethernet cable to the WAN port of the router
6.  Connect to the router using SSH shell under SuperUser account
7.  Make a mtd backup (optional, see related section)
8.  Change bootflag to Sercomm1 and reboot:
        printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
        reboot
9.  Login to the router web interface under admin account
10. Remove dots from the OpenWrt factory image filename
11. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 172.16.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 171.16.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses (fw 2.0.9)
------------------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:e8    |
| WAN | label + 1  | *:e9    |
| 2g  | label + 4  | *:ec    |
| 5g  | label + 5  | *:ed    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

Factory image format
--------------------
+---+-------------------+-------------+--------------------+
| # | Offset            | Size        | Description        |
+---+-------------------+-------------+--------------------+
| 1 | 0x0               | 0x200       | Tag Header Factory |
| 2 | 0x200             | 0x100       | Tag Header Kernel1 |
| 3 | 0x300             | 0x100       | Tag Header Kernel2 |
| 4 | 0x400             | SIZE_KERNEL | Kernel             |
| 5 | 0x400+SIZE_KERNEL | SIZE_ROOTFS | RootFS(UBI)        |
+---+-------------------+-------------+--------------------+

Co-authored-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Maximilian Weinmann <x1@disroot.org>
(cherry picked from commit 8fcfb21b16)
2023-06-17 12:59:37 +02:00
Tianling Shen
a46e5ce4ad rockchip: fix setup network config for nanopi r2c
Without it the WAN port won't be initialized properly.

Fixes: 8f578c15b3 ("rockchip: add NanoPi R2C support")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit d312f12b1a)
2023-06-17 12:21:13 +02:00
John Audia
1b6f2af148 kernel: bump 5.15 to 5.15.117
Manually rebased:
	generic/backport-5.15/346-v5.18-01-Revert-ata-ahci-mvebu-Make-SATA-PHY-optional-for-Arm.patch

Removed upstreamed:
	generic/backport-5.15/830-v6.2-ata-ahci-fix-enum-constants-for-gcc-13.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 0e89ba8430)
2023-06-17 12:09:03 +02:00
John Audia
1de5f74062 kernel: bump 5.15 to 5.15.116
All patches rebased automatically.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 5dc78d8f18)
2023-06-17 12:09:03 +02:00
John Audia
81979018e0 kernel: add CONFIG_DRM_RCAR_USE_LVDS is not set
Added missing symbol.

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit fc3383a558)
2023-06-17 12:09:03 +02:00
John Audia
68bc059c55 kernel: bump 5.15 to 5.15.115
Manually rebased:
	backport-5.15/603-v5.19-page_pool-Add-recycle-stats-to-page_pool_put_page_bu.patch
	pending-5.15/723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch*

Removed upstreamed:
	generic-backport/610-v6.3-net-page_pool-use-in_softirq-instead.patch[1]
	backport-5.15/705-12-v6.0-net-dsa-mt7530-rework-mt753-01-_setup.patch[2]
	backport-5.15/790-v6.4-0010-net-dsa-mt7530-split-off-common-parts-from-mt7531_se.patch[3]
	backport-5.15/703-10-v5.16-net-dsa-introduce-helpers-for-iterating-through-port.patch[4]

All other patches automatically rebased.

* Modified to define the variable i as suggested by DragonBluep in PR discussion.
  See: https://github.com/openwrt/openwrt/pull/12823#issuecomment-1578518576

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.115&id=3af319d5147454dc63665ef451229c674b538377
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.115&id=0753c1ef24194580f7165ae6e259b59a851392f2
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.115&id=5a7266feaa6d708fc6880a161786eaa884ef3c8e
4. 9902f91cf6

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 5714660643)
2023-06-17 12:09:03 +02:00
Christian Marangi
6f9495b896
ipq806x: set PERFORMANCE as the default cpufreq governor
Move default cpufreq governor from ONDEMAND to PERFORMANCE. The temp
increase is just 2°C and Watt usage the change is minimal in the order
of additional millwatt. The SoC and krait in general looks to suffer for
some problem with cache scaling. To have better system stability, force
cpu freq and cache freq to the max value supported by the system. This
follows mvebu platform where cpufreq is broken and cause minimal
temp/watt increase.

User can still tweak the governor to ondemand using sysfs entry if
needed.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6f5ea752d7)
2023-06-16 11:42:40 +02:00
Christian Marangi
11ad38f0bb
Revert "ipq806x: disable cache and fabric devfreq driver to improve stability"
This reverts commit 60fc93b359.

Reenable devfreq and revert for both 5.15 and 6.1.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 37e4593213)
2023-06-16 11:41:35 +02:00
Daniel González Cabanelas
dee8ca626c bcm63xx: fix the Home Hub 2a power LED
Power LED register is wrong at dts. Fix it.

Fixes: 9ceeaf4c6c ("brcm63xx: switch to hardware led controllers")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 0e01ba9361)
2023-06-16 14:41:05 +02:00
Álvaro Fernández Rojas
66e1bef8f7 bmips: add support for Comtrend VG-8050
The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM63169
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 128 MB DDR
 - Flash: 128 MB NAND
 - LAN switch: Broadcom BCM53125, 5x 1Gbit
 - Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 2x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 47cc09aa7a)
2023-06-16 09:50:34 +02:00
Álvaro Fernández Rojas
b073d6cf7a bmips: dts: dgnd3700: fix WAN port
All switch ports are labeled as port@address so let's follow the same pattern.

Fixes: ed79519b8d ("bmips: add support for Netgear DGND3700 v1, DGND3800B")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d9210c5ff7)
2023-06-15 20:58:18 +02:00
Álvaro Fernández Rojas
3d66e7f1db bmips: add support for Sercomm AD1018
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 @ 320Mhz
 - RAM: 64 MB (v1) / 128 MB (v2) DDR
 - Flash: 128 MB NAND
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
 - USB: 1x 2.0
 - Buttons: 3x (reset)
 - LEDs: yes
 - UART: yes

Installation via OEM web UI:
  1. Use the admin credentials to login via web UI
  2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
  3. Press "Update Firmware" button and wait some minutes until it finish

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 38ebb2eafd)
2023-06-15 20:58:16 +02:00