This commit adds OpenWRT's LED aliases to the board DTS
for showing system status on the NanoPi R3S.
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the FriendlyElec NanoPi R3S.
CPU: Rockchip RK3566, Quad-core Cortex-A55
RAM: 2GB LPDDR4X
Ethernet: GMAC RTL8211F GbE, PCIe R8111H GbE
USB3.0 Host: Type-A x1
Storage: MicroSD Slot x 1, and optional on-board 32GB eMMC
Debug Serial Port: 3.3V TTL, 3-pin 2.54mm pitch connector, 1500000 bauds
LED: LED x 3
RTC: One low-power RTC, supports backup battery input
Both GbE controllers are working (WAN eth0, LAN eth1).
Appropriate LAN/WAN interface assignments and MAC address generation.
All three LEDs are working.
USB appears to be working and has been tested with mass storage.
Installation - microSD:
-Uncompress the OpenWRT sysupgrade.img.gz
-Write image to microSD card using dd or similar tool
Installation - eMMC:
-Boot from microSD
-Uncompress the OpenWRT sysupgrade.img.gz
-Flash to eMMC : dd if=x.img of=/dev/mmcblk0
-sync
-Remove microSD card
-Reboot
Signed-off-by: Kevin Zhang <kevin@kevinzhang.me>
Link: https://github.com/openwrt/openwrt/pull/16738
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This board is also as known as Bananapi BPi-M7.
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8/16/32GB LPDDR4/LPDDR4x RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (RED / GREEN)
16GB/32GB/64GB/128GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
USB 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16462
Signed-off-by: Nick Hainke <vincent@systemli.org>
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This enables the M.2 E-key on ROCK 5A board.
Reorder rk356x patch while at it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes model name in dts as below:
Radxa ROCK3 model A -> Radxa ROCK 3A
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16232
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kconfig symbols CONFIG_ARM64_CNP and CONFIG_ARM64_EPAN got exposed
by enabling CONFIG_ARM64_PAN. Enable them as well, as just like for
PAN, also EPAN and CNP will be detected at runtime at no cost.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable the CONFIG_ARM64_PAN kernel security option, which leverages the
ARMv8.1 Privileged Access Never (PAN) extension to prevent the kernel
from directly accessing user space memory.
Instead, copy_to_user and similar functions must be used for data
transfer between kernel and user space. This feature is automatically
disabled at runtime on CPUs without PAN support, making it a no-op in
those cases.
Link: https://github.com/openwrt/openwrt/pull/16189
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
2500 Base-T
RGB LED
eMMC Connector
SPI-NOR 16MB
Micro-SD Slot
2x USB 2.0 Port
2x USB 3.0 Port
Headphone Jack
M.2 E-Key
M.2 M-Key
USB PD 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16/32GB LPDDR4X RAM
1000 Base-T
Status LED
eMMC/SPI Connector
Micro-SD Slot
2x USB 3.0 Port
2x USB 2.0 Port
Headphone Jack
M.2 E-Key
USB PD/QC 5/9/12/15/20V Power
Install
--------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we have rk3588 support :)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SUPPORTED_DEVICES is required for Radxa ROCK Pi S.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We need to configure the led and network config for this board on
start as per the others
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches for the nanopi r6s board, backporting from 6.9 where
basic support is landing.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15607
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the image check failed on system upgrade
"Image check failed:
upgrade: Device radxa,rock3a not supported by this image
upgrade: Supported devices: radxa,rock-3a"
Signed-off-by: Tomas Lara <tl849670@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi E v3.0 has a RTL8723DU Wi-Fi 4 on-board device. enable
it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S has a RTL8723DS Wi-Fi 4 on-board device. enable it.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15910
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Import patch from mainline Linux to fix issue with PERST# signal
polarity.
Quote from commit message:
"This extra, very short, PERST# assertion + deassertion has been
reported to cause issues with certain WLAN controllers, e.g. RTL8822CE."
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Testing turned out that the HWRNG quality varies greatly on RK3566,
even on supposedly identical boards and SoC revisions.
Hence enable the HWRNG driver only on RK3568 for now.
Allow users to simply tune sample_count and quality to allow easily
testing results on different boards and SoCs.
Link: https://patchwork.kernel.org/project/linux-arm-kernel/cover/cover.1720969799.git.daniel@makrotopia.org/
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Radxa ROCK Pi E v3.0 is a compact networking SBC[1] using the Rockchip
RK3328 SoC.
Hardware
--------
- Rockchip RK3328 SoC
- Quad A53 CPU
- 512MB/1GB/2GB DDR4 RAM
- 4/8/16/32GB eMMC
- Micro SD Card slot
- WiFi 4 and BT 4, or WiFi 5 and BT 5 (not supported yet)
- 1x 1000M Ethernet with PoE support (additional PoE HAT required)
- 1x 100M Ethernet
- 1x USB 3.0 Type-A port (Host)
- 1x 4-ring 3.5mm headphone jack
- 40 Pin GPIO header
[1] https://radxa.com/products/rockpi/pie
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15984
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK Pi S is a small in size, full in features SBC[1] using the
Rockchip RK3308B SoC.
Hardware
--------
- Rockchip RK3308B SoC
- Quad A35 CPU
- 256/512MB DDR3 RAM
- Optional 4/8GB eMMC
- Micro SD Card slot
- Optional WiFi 4 and BT 4 (not supported yet)
- 1x 100M Ethernet with PoE support (additional PoE HAT required)
- 1x USB 2.0 Type-A port (Host)
- 1x USB 2.0 Type-C port (OTG)
- 2x 26 Pin GPIO header
[1] https://radxa.com/products/rockpi/pis
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15933
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
stop "heartbeat" which happens before OpenWrt controls LED. instead,
just turn LED on.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15913
Signed-off-by: Robert Marko <robimarko@gmail.com>
use u-boot-rockchip.bin to copy SPL/TPL/U-Boot to the image.
since binman was used in mainline u-boot for rockchip, we can use
u-boot-rockchip.bin instead of idbloader.img and u-boot.itb.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15815
Signed-off-by: Robert Marko <robimarko@gmail.com>
