The Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301) has two Ethernet ports,
labeled MAIN and SECONDARY, connected to gmac2 and gmac1, respectively.
The standard probe order results in gmac1/SECONDARY being eth0 and
gmac2/MAIN being eth1. This does not match the stock firmware, is
contrary to user expectation, causes the wrong (high) MAC address to be
used in a bridged configuration (the default for this device), and makes
the gmac2/MAIN port unusable in the preinit environment (such as for
failsafe). Until a recent patch, gmac1/SECONDARY (eth0) was not even
usable.
This reorders the ports so that gmac2/MAIN is eth0, and the now-working
gmac1/SECONDARY is eth1. eth0 has the low MAC address and eth1 has the
high; when bridged, the bridge takes on the correct low MAC address.
This matches the stock firmware. The MAIN port is usable for failsafe
during preinit.
This device does not have a switch on board, so there's no possibility
to remap ports via switch configuration. "ip link set $interface name"
is used instead, during preinit before networking is configured.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
Unlike many ipq806x devices, Ubiquiti UniFi AC HD (UAP-AC-HD, UAP301)
has no switch on board. Its two Ethernet ports are connected to Atheros
AR8033 PHYs. It is not appropriate to use fixed-link in this
configuration. Instead, configure the correct PHYs in the device tree
configuration to allow the at803x driver to load.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
On a Ubiquiti UniFi AC HD (ubnt,unifi-ac-hd, UAP-AC-HD, UAP301), a
forced speed on gmac1 is set in the QSGMII PCS_ALL_CH_CTL register,
presumably by the bootloader (4.3.28), preventing the interface from
being usable. The QSDK NSS GMAC driver takes care to clear the forced
speed in nss_gmac_qsgmii_dev_init
(https://source.codeaurora.org/quic/qsdk/oss/lklm/nss-gmac/tree/ipq806x/nss_gmac_init.c?h=nss
at d5bb14925861).
gmac1 is connected to the port on the device labeled SECONDARY, and is
currently eth0 but will be switched to eth1 by a subsequent patch. By
clearing the QSGMII PCS forced speed during dwmac initialization when
SGMII is in use, this port becomes usable.
This patch is upstreamable, and will be sent upstream after successful
testing in OpenWrt.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Build-tested: ipq806x/ubnt,unifi-ac-hd
Run-tested: ipq806x/ubnt,unifi-ac-hd
The kernel image is too big now and the build fails.
WARNING: Image file zyxel_nbg6716-kernel.bin is too big: 4205404 > 4194304
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In order to allow easily updating the bootloader on eMMC also provide
artifacts for that. Support for updating bootloader via TFTP will be
added to the loader CLI menu in a follow-up commit.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It is possible to select CONFIG_MTD_PARSER_TRX on the mediatek now. Add
this option to the kernel configuration file.
Fixes: 58c5e25664 ("mediatek: support non standard trx magic values")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This partly reverts commit 20a924d2ae.
This commit broke the build of the Mediatek target with kernel 5.4, for
kernel 5.10 it is fine.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The spi-ath79 driver performs the chipselect by writing to dedicated
register in the SPI register block. So the GPIO numbers were not used.
Tested-on: Enterasys WS-AP3705i
Signed-off-by: David Bauer <mail@david-bauer.net>
All chipsets from AR7100 up to QCA9563 have three dedicated chipselect
lines for the integrated SPI controller. Remove the number of
chipselects from the platform data, as there is no need to manually set
this to a different value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the SPI_MASTER_GPIO_SS flag for the spi-ath79 driver. Otherwise,
the custom chipselect function is never called. This breaks hardware,
where the three dedicated chipselect lines are used instead of generic
GPIO pins.
Signed-off-by: David Bauer <mail@david-bauer.net>
This came up in an upstream commit: "
b1dd9bf688b0 "net: phy: broadcom: Fix RGMII delays for BCM50160 and BCM50610M"
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that."
So the "rgmii" phy-mode has always been wrong, but went unnoticed since
the broadcom phy driver didn't push the delay settings to the chip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The CLK125 output pin at the ethernet PHY is connected via capacitor to
GND and nowhere else. Disable it. Also tune the LED masks.
The MPP56 and MPP60 pins at the SoC are conected to the μPD720202 USB3.0
chip:
- MPP56: wired to PCIe CLKREQ# (out)
- MPP60: wired to PCIe RESET# (in)
Configure the pcie pinmux for these pins.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
These have long been obsolete. For reference, here's the Linux version where
each symbol has been dropped:
CONFIG_IP6_NF_QUEUE - 3.5
CONFIG_IP6_NF_TARGET_LOG - 3.4
CONFIG_IP_NF_MATCH_DSCP - 2.6.19
CONFIG_NF_CONNTRACK_IPV4 - 4.19
CONFIG_NF_CONNTRACK_IPV6 - 4.19
CONFIG_NF_CONNTRACK_RTCACHE - out-of-tree, superseded by flow offloading
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.
It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.
One use case is where multiple IPs and gateways assign on one net port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new EEE patch is accepted upstream, so backport it and replace the
current one.
Cc: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
This CFI patch was accepted upstream for 5.13. Move it away from under
ath79 and place under backports to be removed in due time.
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.
Tested on a RouterBOARD 922UAGS-5HPacD board.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Commit f724a583dc updated the nand-rb4xx driver to the 5.10 testing
kernel, but forgot to add the new kernel config symbol it introduces to
the 5.10 config.
Fixes: f724a583dc ("ath79: mikrotik: update nand-rb4xx driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Generating the sdcard.img.gz file requires the initramfs/recovery
image to be present. Use the newly introduced 'append-image-stage'
build command to fix the ImageBuilder for the BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build the driver for the in-SoC AHCI SATA host as module, just like for
the other subtargets. No board requires booting off SATA, so we don't
need to have it built-in. All boards with SATA support already select
kmod-ata-ahci-mtk which provides the module.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It's in backports-5.4, but it wasn't ever merged. Upstream followed another
approach, with flow offloading, which has much better performance. Drop this
obsolete patch and refresh the kernel patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Make sure all compression algorithms are enabled, for the time being, in order
not to break sysupgrade. In the future, we'd like to disable all except zstd, as
it's the best all-around performer.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Only two patches against mainline remains. Switch to v5.10
which works very nicely with all Gemini devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[backported don't disable option CONFIG_BPF_SYSCAL]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove upstreamed parts from 100-ubnt_edgerouter2_support.patch.
Compile and runtime tested on Ubiquiti EdgeRouter Lite.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This patch broke while refreshing on a kernel bump. It adds the
config_aneg function twice to the AR8035 PHY now.
Restore the old behavior to restore the patches original intent.
Fixes commit 57e32650ef ("kernel: bump 5.10 to 5.10.31")
Signed-off-by: David Bauer <mail@david-bauer.net>
Use an alternative path to access the CID of the SD card in MMC0, used
for the generation of MAC addresses. With Kernel 5.10, the device name
of the MMC controller changed, breaking MAC address generation.
The new path is compatible with Kernel 5.4 as well as Kernel 5.10.
Signed-off-by: David Bauer <mail@david-bauer.net>
fix the following build error when building with test kernel:
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This feature is already supported in kernel. Add definition
and configuration in Makefile of OpenWRT.
It is tested on board Dibbler with processor V1605B.
Dmesg is as below.
--------------------------------------------
[ 0.317122] smpboot: CPU0: AMD Ryzen Embedded V1605B with Radeon
Vega Gfx (family: 0x17, model: 0x11, stepping: 0x0)
[ 8.227270] libphy: amd-xgbe-mii: probed
[ 8.228189] amd-xgbe 0000:02:00.1 eth0: net device enabled
[ 8.228999] libphy: amd-xgbe-mii: probed
[ 8.229921] amd-xgbe 0000:02:00.2 eth1: net device enabled
.....
[ 11.760869] br-lan: port 1(eth0) entered blocking state
[ 11.761365] br-lan: port 1(eth0) entered disabled state
[ 11.762019] device eth0 entered promiscuous mode
[ 11.785285] 8021q: adding VLAN 0 to HW filter on device eth1
[ 16.881431] amd-xgbe 0000:02:00.1 eth0: Link is Up - 1Gbps/Full -
flow control off
[ 16.882108] br-lan: port 1(eth0) entered blocking state
[ 16.882583] br-lan: port 1(eth0) entered forwarding state
[ 16.883249] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
-----------------------------------------------
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
This updates the NAND driver for MikroTik RB4XX series to work with
kernel 5.10, similarly to the ar934x-nand driver (fb64e2c3).
Support for kernel 5.10 was added to all ath79 subtargets except for the
mikrotik one by commit d6b785d, since patch 920-mikrotik-rb4xx.patch
needed to be reworked. Later, commit f8512661 enabled kernel 5.10 for
the mikrotik subtarget with the nand-rb4xx driver still pending, which
is updated and added back by this patch.
Compile-tested only.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The crypto engine in Armada 370 SoCs is currently broken. It can be
checked installing the required packages for testing openssl with hw
acceleration:
opkg install openssl-util
opkg install kmod-cryptodev
opkg install libopenssl-devcrypto
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Refresh patches.
Tested on a dual-core MT7621 device (Ubiquiti ER-X) and a single-core
MT7621 device (Netgear R6220).
This change will make future kernel upgrades easier (avoids conflicts
with upstream).
Link: https://lore.kernel.org/lkml/20210407200738.149207-1-ilya.lipnitskiy@gmail.com/
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Reduce spi-max-frequency for Xiaomi MI Router 4AG model
Xiaomi MI Router 4AG MTD uses two flash chips (no specific on router versions when produced from factory) - GD25Q128C and W25Q128BV.
These flash chips are capable of high frequency, but due to poor board design or manufacture process.
We are seeing the following errors in the linux kernel bootup:
`spi-nor spi0.0: unrecognized JEDEC id bytes: cc 60 1c cc 60 1c
spi-nor: probe of spi0.0 failed with error -2`
This causes the partitions not to be detected
`VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6`
Then creates a bootloop and a bricked router.
The solution to limit this race condition is to reduce the frequency from 80 mhz to 50 mhz.
Signed-off-by: David Bentham <db260179@gmail.com>
This makes no sense on anything but the IXP4xx platform
that we do not even support anymore. If we bring it back,
it can be selectively enabled for that platform only.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This config is for platforms that have:
A) CONFIG_THERMAL set (we disable it by default)
B) Has thermal zones that need to control cpufreq
This is not suitable for default config, it needs to be enabled
on a per-target basis in individual configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We do not enable GPIO_CDEV so do not enable CDEV_V1
either. As we rebuild the whole userspace and kernel
in OpenWRT it doesn't make any sense to support the
old ABI anyway: the new one should be used by default.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This CMA memory allocation option only applies to NUMA
(Non-Uniform Memory Access) systems which are seldom
the kind of systems that OpenWRT address.
It is safe to assume that any system that need this
option would turn it on locally.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The non-MQ CFQ, deadline and noop IO schedulers are
deleted from the Linux kernel
since commit f382fb0bcef4c37dc049e9f6963e3baf204d815c
"block: remove legacy IO schedulers".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains. No
manual intervention needed.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Removed upstreamed:
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Build system : x86_64
Build-tested : ipq806x/R7800
Run-tested : ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
This patch ist not required, as it only has an effect in case the GPIO
descriptors supplied to num-cs are valid.
As this is not the case for ath79, this patch can safely be omitted. The
issue it tried to fix is actually fixed with
0054-spi-sync-up-initial-chipselect-state.
Signed-off-by: David Bauer <mail@david-bauer.net>
When adding Kernel 5.10 support, the kernel configuration did not
include the LED driver required for the UniFi 6 LR. Also the actual
driver source went missing.
Fixes commit c46ccb69d1 ("mediatek: mt7622: add Linux 5.10 support")
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD.
GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable
or disable transmission, but no change is observed. Therefore, it is
left as output high to ensure the SFP module is forced to transmit.
Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD
1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router
iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port
or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers
950 Mbps symmetric.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Respect the generic kernel config setting, which is "enabled" tree-wide, as
previously done for sunxi.
Ref: 247ef4d98b ("sunxi: enable CONFIG_BPF_SYSCALL and CONFIG_EMBEDDED")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP
boards using a AR8033 SGMII PHY.
Otherwise, 10 Mbit/s links do not transfer data.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite
/ Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes incorrect supported link modes indicated when using ethtool
on the Ubiquiti UniFi AC lite / LR / Mesh.
eroot@OpenWrt:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
The reason for this is, that since kernel 5.4 the PHY capabilities are
read dynamically from the PHY. As Ubiquiti leaves the PHY in a wrong
state, the capabilities of the SGMII side of the PHY are read.
As a side effect, 10 Mbit/s link modes did not work on these boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
From Frank Wunderlich <frank-w@public-files.de>:
Issue were traffic problems after a while with increased ping times if
flow offload is active.
It turns out that key_offset with cookie is needed in rhashtable_params
and head_offset was defined twice.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DTS properties that match *-gpios are treated specially.
Use ngpios instead, as most GPIO drivers upstream do.
Fixes 5.10 DTS errors such as:
OF: /palmbus@300000/gpio@600: could not find phandle
Fixes DTC warnings such as:
Warning (gpios_property): /palmbus@300000/gpio@600:ralink,num-gpios:
Could not get phandle node for (cell 0)
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Use an existing kernel config symbol to fix devices whose ramstart is
not zero. See upstream patch message for more details.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Tobias Wolf <dev-NTEO@vplace.de>
Cc: Daniel Golle <daniel@makrotopia.org>
The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and
does not hold a lock, which causes a race condition when multiple
threads try to access a register, they may get unexpected results.
To avoid this, handle the MDIO lock manually, and use the unlocked
__mdiobus_{read,write} in the critical section.
This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN
operation and the swconfig LED link status poll race between each other.
[1] https://forum.openwrt.org/t/mysterious-vlan-ids-on-mt7621-device/64495
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
CONFIG_MIPS_CMDLINE_FROM_DTB is set to 'y' for all ramips targets
already, which will ensure that the value of 'bootargs' will take
precedence over whatever is in arcs_cmdline.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This fixes partitioning on Linksys EA9500. With this change only the
currently used firmware MTD partition gets parsed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When adding the patch for the missing register, the patch file for the
testing kernel 5.10 was not included.
Fixes commit fbbad9a9a6 ("ath79: force SGMII SerDes
mode to MAC operation")
Signed-off-by: David Bauer <mail@david-bauer.net>
The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default.
This only allows for 1000 Mbit/s links, however when used with an SGMII
PHY in 100 Mbit/s link mode, the link remains dead.
This strictly has nothing to do with the SerDes calibration, however it
is done at the same point in the QCA reference U-Boot which is the
blueprint for everything happening here. As the current state is more or
less a hack, this should be fine.
This fixes the issues outlined above on a TP-Link EAP-225 Outdoor.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Following changes are made to the Lantiq kernel patches:
0001-MIPS-lantiq-add-pcie-driver.patch
The pci header isn't included by the of_pci header any longer
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
Due to the merge of grx390 and ar10 clocks, extend support to grx390
0025-NET-MIPS-lantiq-adds-xrx200-legacy.patch
The do_carrier arguments was dropped from phy_link_change. The
phylib has always sets the third parameter to true so the flag is
always changed anyway.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
The stuck queue is now passed to xrx200_tx_timeout (the timeout
handler) but not used so far.
0028-NET-lantiq-various-etop-fixes.patch
ioremap has provided non-cached semantics by default since the Linux
2.6 days and was removed with kernel version 5.6.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
0042-arch-mips-increase-io_space_limit.patch
Move IO space extension to laniq specific file
Signed-off-by: Mathias Kresin <dev@kresin.me>
Duplicate kernel 5.4 config and patches for kernel 5.10.
Duplicate the devicetree source files as well, they need kernel 5.10
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the device_type property to mark PCI host bridges as such. With
linux 5.10 it is mandatory, otherwise the PCI IO space is flages as PCI
memory and the PCI init fails.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Check if gendisk is already up instead of trying to figure out parent
mtd device (which didn't work well).
Reported-by: DENG Qingfang <dqfext@gmail.com>
Reported-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Fixes: 2809d00007 ("kernel: support FIT partition parser on mtdblock devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz
Memory: 1GB DDR3
Storage: SDcard, native SATA
Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT
USB: 4x USB 2.0
Installation:
Use the standard sunxi installation to an SD-card.
While the board is very similar to the M2 Ultra board
(the V40 is the automotive version of the R40), as both
the u-boot and kernel supports them separately, and some
pins are different, let's add a separate device spec.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Add SD card image support for installing openwrt to it.
Default to nand upgrade if root device is not mmc block device.
Separate preloader and uboot images for snand are generated.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
The 100-ARM-dts-imx23-introduce-mmc0_sck_cfg.patch does
not need to be copied over as it's already merged upstream.
Other notable change is the USB_CHIPIDEA_OF change to
USB_CHIPIDEA_IMX [1].
[1] https://www.spinics.net/lists/linux-usb/msg193347.html
Compile/runtime-tested on Olinuxino Micro (imx23).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
LPAE should be disabled as the Cortex-A8 cores don't support it,
and the kernel will crash on boot if it's enabled.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Increase the spi-max frequency to 50 MHz, similar to the DIR-842.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
[improve commit title, fix commit message alignment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased due to movement of rx-offload.c in 5.4.110:
layerscape/patches-5.4/802-can-0002-can-rx-offload-fix-long-lines.patch
layerscape/patches-5.4/802-can-0003-can-rx-offload-can_rx_offload_compare-fix-typo.patch
layerscape/patches-5.4/802-can-0004-can-rx-offload-can_rx_offload_irq_offload_timestamp-.patch
layerscape/patches-5.4/802-can-0005-can-rx-offload-can_rx_offload_reset-remove-no-op-fun.patch
layerscape/patches-5.4/802-can-0006-can-rx-offload-Prepare-for-CAN-FD-support.patch
layerscape/patches-5.4/802-can-0018-can-flexcan-use-struct-canfd_frame-for-CAN-classic-f.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
/dts-v1/; must only be specified once.
Fixes: e887049fbb ("mediatek: add alternative bootchain variant
for UniFi 6 LR")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move 480-mtd-set-rootfs-to-be-root-dev.patch to hack-5.10 and fix assumption
about the block device index.
Fixes: 2809d00007 ("kernel: support FIT partition parser on mtdblock devices")
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Builds images for the Ubiquiti Network UniFi 6 LR device running the
U-Boot build added by the previous commits.
Everything but MTD partitions is moved to dtsi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow using the FIT block-device partition partition parser to work on
top of mtdblock devices.
This is more tricky than it sounds as it requires to reorganize the
procedure of registering mtdblock devices in order to avoid locking
troubles caused by the block partition parsers then trying to open
the mtdblock device for reading while locks are still being held.
Fix that by moving the adding of the disks after the entire device
has been probed when locks no longer need to be held.
Also address issue with mtdsuper surfaced when using sub-partitions
which prevented mounting JFFS2 using the /dev/mtdblock* device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
U-Boot has recently added support for having data blobs in uImage.FIT
images stored at offsets after the FDT structure rather than embedding
the data into the FDT structure itself. This is useful as it allows
parts of the image to be mapped by the FIT partition parser, and it
allows the FIT structure itself to be parsed more easily as it usually
fits into single page.
mtdsplit_fit assumed that the total length of an image is identical
to the length of the FDT structure. For uImage.FIT with external data
this assumption no longer holds true.
Add support for uImage.FIT with external data to mtdsplit_fit and in
in that case only split-off rootfs_data -- selecting and mapping rootfs
partition is left to the block partition parser just like on UBI and
block/GPT based platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
commit d6b785d477 ("ath79: add kernel 5.10 support") moved
KERNEL_TESTING_PATCHVER to a subtarget level,
but is looks like Mikrotik subtarget was forgotten.
Also add it for Mikrotik.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This enables building BCM4908 "raw" image that can be flashed using
bootloader web UI. It requires serial console access & stopping booting
by the "Press any key to stop auto run".
It's easy to build vendor like CHK image but it can't be safely flashed
using vendor UI at this point. Netgear implements method called "NAND
incremental flashing" that doesn't seem to flash bootfs partition as
provided.
Above method seems to update vmlinux.lz without updating 94908.dtb. It
prevents OpenWrt kernel from booting due to incomplete DTB file. Full
Netgear R8000P support can be enabled after finding a way to make vendor
firmware flash OpenWrt firmware including the 94908.dtb update.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
OpenWrt was succesfully tested on the GT-AC5300 model. It's possible to:
1. Install OpenWrt using vendor UI
2. Perform UBI aware sysupgrade
3. Install vendor firmware using OpenWrt sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
bcm4908img is a tool managing BCM4908 platform images. It's used for
creating them as well as checking, modifying and extracting data from.
It's required by both: host (for building firmware images) and target
(for sysupgrade purposes). Make it a host/target package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes boot loader LZMA decompression issue,
reported by GitHub user KOLANICH at [0].
The reported LZMA ERROR has date of 2020-07-20, soon after
the device support landed:
Ralink UBoot Version: 3.5.2.4_ZyXEL
....
3: System Boot system code via Flash.
Image Name: MIPS OpenWrt Linux-4.14.187
Created: 2020-07-20 3:39:11 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1472250 Bytes = 1.4 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
[0] fea232ae8f (commitcomment-45016560)
Fixes: 4dc9ad4af8 ("ramips: add support for ZyXEL Keenetic Lite Rev.B")
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
pcie0 is the same for this generation of Senao APs
while eth0, eth1, and wmac can differ
the qca,no-eeprom property has no effect
for the ath10k drivers
Signed-off-by: Michael Pratt <mcpratt@pm.me>
use qca955x_senao_loader.dtsi
because it is the same hardware / partitioning
and some cleanup
Effects:
nodes to match similar boards
- keys
- eth0
- pcie0
bumps SPI frequency to 40 MHz
removes &pll node:
the property is defined in qca955x.dtsi
removes qca,no-eeprom:
has no effect with mtd-cal-data property
(also spelling)
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This device is a Senao-based product
using hardware and software from Senao
with the tar-gz platform for factory.bin
and checksum verification at boot time
using variables stored in uboot environment
and a 'failsafe' image when it fails.
Extremely similar hardware/software to Engenius EAP1200H
and other Engenius APs with qca955x
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Use a similar upgrade method for sysupgrade.bin, like factory.bin,
for Senao boards with the tar.gz OEM upgrade platform,
and 'failsafe' image which is loaded on checksum failure.
This is inspired by the OEM upgrade script /etc/fwupgrade.sh
and the existing platforms for dual-boot Senao boards.
Previously, if the real kernel was damaged or missing
the only way to recover was with UART serial console,
because the OKLI lzma-loader is programmed to halt.
uboot did not detect cases where kernel or rootfs is damaged
and boots OKLI instead of the failsafe image,
because the checksums stored in uboot environment
did not include the real kernel and rootfs space.
Now, the stored checksums include the space for both
the lzma-loader, kernel, and rootfs.
Therefore, these boards are now practically unbrickable.
Also, the factory.bin and sysupgrade.bin are now the same,
except for image metadata.
This allows for flashing OEM image directly from openwrt
as well as flashing openwrt image directly from OEM.
Make 'loader' partition writable so that it can be updated
during a sysupgrade.
tested with
ENS202EXT v1
EAP1200H
EAP350 v1
EAP600
ECB350 v1
ECB600
ENH202 v1
Signed-off-by: Michael Pratt <mcpratt@pm.me>
ath79/tiny kernel config has
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y
from commit
05d35403b2
Because of this, these changes are required for 2 reasons:
1.
Senao devices in ath79/tiny
with a 'failsafe' partition and the tar.gz sysupgrade platform
and a flash chip that supports 4k sectors
will fail to reboot to openwrt after a sysupgrade.
the stored checksum is made with the 64k blocksize length
of the image to be flashed,
and the actual checksum changes after flashing due to JFFS2 space
being formatted within the length of the rootfs from the image
example:
0x440000 length of kernel + rootfs (from sysupgrade.bin)
0x439000 offset of rootfs_data (from kernel log)
2.
for boards with flash chips that support 4k sectors:
saving configuration over sysupgrade is not possible
because sysupgrade.tgz is appended at a 64k boundary
and the mtd parser starts JFFS2 at a 4k boundary.
for boards with flash chips that do not support 4k sectors:
partitioning with 4k boundaries causes a boot loop
from the mtd parser not finding kernel and rootfs.
Also:
Some of the Senao boards that belong in ath79/tiny,
for example ENH202,
have a flash chip that does not support 4k sectors
(no SECT_4K symbol in upstream source).
Because of this, partitioning must be different for these devices
depending on the flash chip model detected by the kernel.
Therefore:
this creates 2 DTSI files
to replace the single one with 64k partitioning
for 4k and 64k partitioning respectively.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
By using the same custom kernel header magic
in both OKLI lzma-loader, DTS, and makefile
this hack is not necessary anymore
However, "rootfs" size and checksum
must now be supplied by the factory.bin image
through a script that is accepted by the OEM upgrade script.
This is because Senao OEM scripts assume a squashfs header exists
at the offset for the original "rootfs" partition
which is actually the kernel + rootfs in this implementation,
and takes size value from the header that would be there with hexdump,
but this offset is now the uImage header instead.
This frees up 1 eraseblock
previously used by the "fakeroot" partition
for bypassing the OEM image verification.
Also, these Senao devices with a 'failsafe' partition
and the tar-gz factory.bin platform would otherwise require
flashing the new tar-gz sysupgrade.bin afterward.
So this also prevents having to flash both images
when starting from OEM or 'failsafe'
the OEM upgrade script verifies the header magic numbers,
but only the first two bytes.
Example:
[ "${magic_word_kernel}" = "2705" ] &&
[ "${magic_word_rootfs}" = "7371" -o "${magic_word_rootfs}" = "6873" ] &&
errcode="0"
therefore picked the magic number
0x73714f4b
which is
'sqOK'
Signed-off-by: Michael Pratt <mcpratt@pm.me>
...and max flash offset
The mtdsplit parser was recently refactored
to allow the kernel to have custom image header magic.
Let's also do this for the lzma-loader
For example:
When implemented together,
this allows the kernel to "appear" to be a rootfs
by OEM software in order to write an image
that is actually kernel + rootfs.
At the same time,
it would boot to openwrt normally
by setting the same magic in DTS.
Both of the variables
have a default value that is unchanged
when not defined in the makefiles
This has no effect on the size of the loader
when lzma compressed.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
U-Boot uses the "bootpartition" variable stored in
"u-boot-env2" to select the active system partition. Allow
updates to enable system switching from OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
It supports flashing OpenWrt images (bootfs & UBI upgrade) as well as
vendor images (whole MTD partition write).
Upgrading cferom is unsupported. It requires copying device specific
data (like MAC) to target image before flashing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This way MTD "bootfs" partition will be always 8+ MiB. This should be
enough for any custom / future firmware to fit its bootfs (e.g. big
kernel) without having to repertition whole flash. That way we can
preserve UBI and its erase counters during sysupgrade.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The purpose of that dummy file is to make CFE work properly with OpenWrt
bootfs. CFE for some reason ignores JFFS2 files with ino 0.
Rename it to 1-openwrt so:
1. It's consistent with bcm63xx
2. It's OpenWrt specific so sysupgrade can distinguish it from vendor
images
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use update_kernel to refresh all patches, required manual updates to:
610-netfilter_match_bypass_default_checks.patch
611-netfilter_match_bypass_default_table.patch
762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch
764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch
Run-tested: x86_64
Nothing screamed out but any funny business with linux bridging should
suspect this update first.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Switch the Netgear DTSI for the Realtek target from the OEM partition
naming scheme to accepted OpenWrt naming practices. A quick git grep for
'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas
grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a
5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq
has access to the flash memory, the Atheros runs fully from RAM.
Specifications
--------------
- Lantiq 500 MHz
- 128MiB RAM
- 128MiB NAND
- 256k Flash
- AR9580 5GHz WiFi
- AR9342 560 MHz
- 64MiB RAM
- AR9328 2.4GHz WiFi
Remarks
-------
This commit only adds support for the Lantiq side of things and
prepares the drivers for communication with the Atheros SoC. Thus,
only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via
another target.
Some kernel patches will be required to add support for the Atheros SoC.
Installation
------------
Use the eva_ramboot.py script to boot the initramfs image. Then, transfer
the sysupgrade image to the device and run sysupgrade to flash it to the
NAND.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
"firmware" partition size defined in the device tree file is 0xf70000,
so the right IMAGE_SIZE is 15808k
Fixes: df1e5d6463 ("ramips: fix partition layout of hiwifi hc5x61")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add 5.10 as testing kernel. Builds successfully with
CONFIG_ALL_KMODS=y enabled.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Some common symbols have been moved to target config.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1] 9b1b89229f ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Add leds and configs
2. Add network configs
3. Add script to clear partial boot flag
4. Hack to use port 5 as cpu port as port 8 connected to eth2
wont pass any frames
5. Enable EA9500 image generation
Hardware Info:
- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
- Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
- DDR3 RAM - 256 MB
- Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
- 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
- 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
- Ports - 8 Ports, 1 WAN Ports
- Antennas - 8 Antennas
- Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1
Flashing Instructions:
1. Connect a USB-TTL table to J6 on the router as well as a
ethernet cable to a lan port and your PC.
2. Power-on the router.
3. Use putty or a serial port program to view the terminal.
Hit Ctrl+C and interrupt the CFE terminal terminal.
4. Setup a TFTP server on your local machine at setup you
local IP to 192.168.1.2
5. Start the TFTP Server
6. Run following commands at the CFE terminal
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2
nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit
7. Reboot router to be presented by OpenWrt
Note: Only installation method via serial cable is supported at the moment.
The trx firmware has to be flashed to both the partitions using following
commands from CFE prompt. This will cover US and Non-US variants.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The uImage.FIT partition parser used to squeeze in FIT partitions in
the range where partition editor tools (fdisk and such) expect the
regular partition. This is confusing people and tools when adding
additional partitions on top of the partition used for OpenWrt's
uImage.FIT.
Instead of squeezing in the additional partitions, rather start with
all uImage.FIT partitions at offset 64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes the following error when building without CONFIG_MODULE_STRIPPED:
FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct
of_device_id is not terminated with a NULL entry!
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support
deep sleep idle states and have a specific cpuidle driver for them.
Enable support for it, while also switching from constant timer ticks to the
idle dynticks model, with the TEO governor.
Run-tested on a Redmi AC2100.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
We've been carrying this patch for many years [1], in order to fix a timer
calibration issue on MT7621. Turns out, after retesting with a recent kernel
(Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls
or inconsistent BogoMIPS values across CPUs).
Manually refreshed:
322-mt7621-fix-cpu-clk-add-clkdev.patch
323-mt7621-memory-detect.patch
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc
Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The Pine64(+) and the SoPine64 baseboard has two USB ports. One of
these (the lower) is connected directly to a USB host, the other
one's (upper) PHY is shared with the separate OTG controller. In
order to get it working, MUSB support needs to be enabled.
As there are other targets which compile MUSB support into the kernel
and not package it into modules, the same is done here.
[ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364250] usb usb5: Product: MUSB HDRC host driver
[ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd
[ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto
[ 1.379891] hub 5-0:1.0: USB hub found
[ 1.383677] hub 5-0:1.0: 1 port detected
[...]
[ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 697.477180] usb 1-1: Product: USB Flash Disk
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
