Commit Graph

532 Commits

Author SHA1 Message Date
Dim Fish
7dbcc1215a mediatek: filogic: add support for Xiaomi AX3000T
**SoC**: MediaTek MT7981B 2x A53
  **Flash**: ESMT F50L1G41LB 128MB
  **RAM**: NT52B128M16JR-FL 256MB
  **Ethernet**: 4x 10/100/1000 Mbps
  **Switch**: MediaTek MT7531AE
  **WiFi**: MediaTek MT7976C
  **Buttons**: Reset, Mesh
  **Power**: DC 12V 1A

1. Get ssh access. Supported stock firmware **1.0.47**
   ```
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A
   ```

2. Backup stock partitions
   ```
   nanddump -f /tmp/BL2.bin /dev/mtd1
   nanddump -f /tmp/Nvram.bin /dev/mtd2
   nanddump -f /tmp/Bdata.bin /dev/mtd3
   nanddump -f /tmp/Factory.bin /dev/mtd4
   nanddump -f /tmp/FIP.bin /dev/mtd5
   nanddump -f /tmp/ubi.bin /dev/mtd8
   nanddump -f /tmp/KF.bin /dev/mtd12
   ```
   Then transfer them to your computer in a safe place.

3. Get firmware information `cat /proc/cmdline`

4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash
   If **firmware=0**
   ```
   ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=1
   nvram set flag_last_success=1
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```
   If **firmware=1**
   ```
   ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=0
   nvram set flag_last_success=0
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```

   Then reboot your router, it should boot to the OpenWrt initramfs system now.

5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin`

1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

   `reboot`

2. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

3. Format ubi and create new ubootenv volume
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
   ```

4. *(Optional **-10Mb** free space) Add recovery boot feature.*
   ```
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
   ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   ```

5. Flash Openwrt U-Boot
   ```
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP
   ```

6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb`

1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

2. Format ubi and Nvram
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   mtd erase Nvram
   ```

3. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Flash stock images from backup
   ```
   mtd write /tmp/BL2.bin BL2
   mtd write /tmp/FIP.bin FIP
   mtd write /tmp/ubi.bin ubi
   ```
   Then reboot your router, waiting it finished rollback in minutes.

   `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
   Then reboot your router, waiting it finished rollback in minutes.

Signed-off-by: Dim Fish <dimfish@gmail.com>
2024-01-06 17:51:11 +01:00
Mohammad Sayful Islam
46a2490e8f ipq807x: add support for Linksys MX4200 V1 and V2
Linksys MX4200 is a 802.11ax Tri-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 512Mb NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
	* RGB system led

* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack

Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part

- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel

- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel

Replace (X) with your model version either 1 or 2

Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2024-01-06 16:13:23 +01:00
Roland Reinl
fdb87a91b4 mediatek: Add support for D-Link EAGLE PRO AI R32
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.

Specification:
 - MT7622BV SoC with 2.4GHz wifi
 - MT7975AN + MT7915AN for 5GHz
 - MT7531BE Switch
 - 512MB RAM
 - 128 MB flash
 - 2 LEDs (Status and Internet, both can be either orange or white)
 - 2 buttons (WPS and Reset)

Compared to M32, the R32 has the following differences:
 - 4 LAN ports instead of 2
 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001
 - Individual LEDs for power and internet
 - MAC address is stored at another offset in the ODM partition

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x81
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Flashing via Recovery Web Interface:
 - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the deivce
 - Keep the reset button pressed until the internet LED blinks fast
 - Open a Chromium based and goto http://192.168.0.1
 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin

Flashing via uBoot:
 - Open the case, connect to the UART console
 - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
 - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
 - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
 - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
 - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
 - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
 - Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
 - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the deivce
 - Keep the reset button pressed until the internet LED blinks fast
 - Open a Chromium based and goto http://192.168.0.1
 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
 - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
 - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
 - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
 - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin

Revert back to stock using uBoot:
 - Open the case, connect to the UART console
 - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides the previously created backup of the Kernel1 partition.
 - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
 - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to FLASH will start. After a few seconds the stock firmware should start again

There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.

Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
 - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
 - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
 - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2024-01-02 21:22:46 +01:00
Xavier Franquet
782eb05008 mediatek: filogic: add support ASUS RT-AX59U
(based on support for ASUS RT-AX59U by liushiyou006)

SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)

Upgrade from AsusWRT to OpenWRT using UART

    Download the OpenWrt initramfs image.
    Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.

    Connect the PC with TFTP server to the RT-AX59U.
    Set a static ip on the ethernet interface of your PC.
    (ip address: 192.168.1.70, subnet mask:255.255.255.0)
    Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.

    Download & Boot the OpenWrt initramfs image.

    $ setenv ipaddr 192.168.1.1
    $ setenv serverip 192.168.1.70
    $ tftpboot 0x46000000 rtax59u.bin
    $ bootm 0x46000000

    Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.

    $ sysupgrade -n <path-to-sysupgrade.bin>

Upgrade from AsusWRT to OpenWRT using WebUI

    Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq

    Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file

    Wait for OpenWRT to boot (192.168.1.1).

    Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command

MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.

              : Stock             : OpenWrt
  WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
  WLAN 2g (2) :                   : CA:xx:xx:0D:xx:D4
  WLAN 2g (3) :                   : CE:xx:xx:0D:xx:D4
  WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
  WLAN 5g (2) :                   : CE:xx:xx:1D:xx:D5
  WLAN 5g (3) :                   : C2:xx:xx:1D:xx:D5

  WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
  WLAN 2g (2) :                   : 0A:xx:xx:76:xx:BE
  WLAN 2g (3) :                   : 0E:xx:xx:76:xx:BE
  WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
  WLAN 5g (2) :                   : 0E:xx:xx:76:xx:BF
  WLAN 5g (3) :                   : 02:xx:xx:76:xx:BF

Signed-off-by: Xavier Franquet <xavier@franquet.es>
2023-12-31 00:03:24 +01:00
Mikhail Zhilkin
485adc9d3c mediatek: add support for Routerich AX3000
This PR is continuation of work under "mediatek: add support for Routerich
AX3000" #13703 by the agreement with PR #13703 original author (Maximilian
Weinmann <x1@disroot.org>). All reviews from the previous PR were taken
into into account.

Routerich AX3000 is a wireless WiFi 6 router.

Specification
-------------
- SoC       : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM       : DDR3 256 MiB (ESMT M15T2G16128A)
- Flash     : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN      : MediaTek MT7976CN dual-band WiFi 6
  - 2.4 GHz : b/g/n/ax, MIMO 2x2
  - 5 GHz   : a/n/ac/ax, MIMO 2x2
- Ethernet  : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
- USB       : 1x 2.0
- UART      : through-hole on PCB
  - [J500] GND, TX, RX, 3.3V (115200n8)
- Buttons   : Mesh, Reset
- LEDs      : 1x Power (Blue)
              1x WiFi 2.4 GHz (Blue)
              1x WiFi 5 GHz (Red)
              1x Mesh (Blue)
              3x LAN activity (Blue)
              1x WAN activity (Blue)
              2x WAN no-internet (Red)
- Power     : 12 VDC, 1.5 A

Installation
------------
Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface
(without keeping settings).

Return to stock
---------------
Install stock firmware image (without keeping settings) using OpenWrt
sysupgrade method.

Recovery
--------
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 24:0f:5e:xx:xx:b4 | label     |
| LAN     | 24:0f:5e:xx:xx:b5 | label+1   |
| WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2   |
| WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3   |
+---------+-------------------+-----------+
The WLAN 2g MAC was found in 'Factory', 0x4

Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-12-26 17:17:23 +01:00
Ian Oderon
4300bc6688 mediatek: add support for Zbtlink ZBT-Z8103AX
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.

Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi

Buttons:
Reset-Mesh

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Signed-off-by: Ian Oderon <ianoderon@gmail.com>
2023-12-26 00:02:19 +01:00
Rafał Miłecki
de94eceee6 uboot-envtools: bump PKG_RELEASE
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-12-13 08:53:36 +01:00
Rafał Miłecki
3ed7abfc5a uboot-envtools: fix reading NVMEM device's compatible value
Fixes: fea4ffdef2 ("uboot-envtools: update to 2023.04")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-12-13 08:52:23 +01:00
Mikhail Zhilkin
f3cdc9f988 ramips: add support for Rostelecom RT-FE-1A
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Power (green, unmanaged)
   - 1x Status (green, gpio)
   - 1x 2.4G (green, hardware, mt76-phy0)
   - 1x 2.4G (blue, gpio)
   - 1x 5G (green, hardware, mt76-phy1)
   - 1x 5G (blue, gpio)
   - 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------

1.  Login to the router web interface (default http://192.168.0.1/)
    under "admin" account

2.  Navigate to Settings -> Configuration -> Save to Computer

3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
    cfgtool.py -u configurationBackup.cfg

4.  Open configurationBackup.xml and find the following block:

<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>

5.  Replace <some value> by a new superadmin password and add a line
    which enabling superadmin login after. For example, the block after
    the changes:

<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>

6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml

7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router

8.  Login to the router web interface (superadmin:xxxxxxxxxx, where
    xxxxxxxxxx is a new password from the p.5)

9.  Enable SSH access to the router (Settings -> Access control -> SSH)

10. Connect to the router using SSH shell using superadmin account

11. Run in SSH shell:
    sh

12. Make a mtd backup (optional, see related section)

13. Change bootflag to Sercomm1 and reboot:
    printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
    reboot

14. Login to the router web interface under admin account

15. Remove dots from the OpenWrt factory image filename

16. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
   cd /tmp
   for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
   tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
   tftp -l mtd.md5 -p 192.168.0.2

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g  | label + 2  | f4:*:68 |
| 5g  | label + 3  | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-12-06 00:12:56 +01:00
David Bauer
dd5d4e24af uboot-envtools: fix GL-MT2500 offset
The previous offsets did also work, as they've wrapped back to 0x0.
However, in reality the environment starts at offset 0x0 of the
u-boot-env MMC partition.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-12-03 06:56:02 +01:00
David Bauer
1239668648 mediatek: add support for GL.iNet GL-MT2500
Hardware
--------
SoC:  MediaTek MT7981BA
RAM:  1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC:  8GB eMMC (Samsung 8GTF4R)
ETH:  1000Base-T LAN (ePHY)
      2500Base-T WAN (MaxLinear GPY211C)
BTN:  1x Reset Button
LED:  System (blue/white)
      VPN (white)
USB:  1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
      Don't connect 3.3V!

Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!

Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-27 08:02:41 +01:00
Rani Hod
e29f4a3f70 ath79: add support for D-link DAP-1720 A1
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)

Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
  775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
  64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
  16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
  1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
  * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
    3x3 802.11n;
  * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
    3x3 802.11ac Wave 1;
  * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
  * RSSI low (red/green) [D2];
  * RSSI medium (green) [D3];
  * RSSI high (green) [D4];
  * status (red/green) [D5];
* GPIO buttons:
  * WPS [SW1], co-located with status LED;
  * reset [SW4], accessible via hole in the side;
* Serial/UART:
  Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
  125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
  * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
  * on/off slide switch [SW2] (disconnects VCC mechanically);
  * unpopulated footprints for a Wi-Fi LED [D1];
  * unpopulated footprints for a 4-pin 3-position slide switch (SW3);

MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;

Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
  standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
  firmware) from D-Link Web Recovery. To enter web recovery, keep reset
  button pressed and then power on the device. Reset button can be
  released when the red status LED is bright; it will then blink slowly.
  Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
  upload 'recovery.bin'. Note that in web recovery mode the device
  ignores ping and DHCP requests.

Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.

Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-26 18:27:35 +01:00
Chukun Pan
4825defe44
uboot-envtools: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:35 +01:00
Nicolò Veronese
2a0805fd3d uboot-envtools: add support for Zyxel EX5601-T0 ubootmod
The ubootmod bootlaoder for EX5601-T0 uses two partitions
 in ubi to store enviroment variables. so proper config
 is needed.

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2023-11-25 14:51:21 +01:00
Daniel Golle
c8c2f52262 mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-24 21:28:35 +00:00
Daniel Golle
2634d3f855 uboot-envtools: add settings for Synology DS213j
Add settings to be able to access the U-Boot environment on the
Synology DS213j NAS.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-20 13:40:17 +00:00
Chukun Pan
b42c527228 uboot-mediatek: add JCG Q30 PRO support
The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-19 16:52:16 +01:00
Daniel Golle
f8414f1a6f uboot-envtools: add environment config for MeiG SLT866
Add configuration to access U-Boot environment on MeiG SLT866.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-03 21:16:29 +00:00
Weiping Yang
c7baca3bb6 ath79: add support for GL.iNet GL-S200
Specifications:
SoC: QCA9531(650MHz)
RAM: DDR2 128M
Flash: SPI NOR 16M + SPI NAND 128M
WiFi: 2.4GHz with 2 antennas(WiFi/Thread)
Ethernet:
    1xLAN(10/100M)
    2xWAN(10/100M)
Button: 1x Reset Button
Switch: 1x Mode switch
LED: 1x Blue LED + 1x White LED + 1x Orange LED
IOT: Thread + ZigBee/Zwave

By uboot web failsafe:
Push the reset button for 5 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2023-10-31 13:53:11 +01:00
Milan Krstic
17465fc77e ramips: add support for ZyXEL LTE5398-M904
ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS
port.

Specifications:

* SoC: Mediatek MT7621AT
* RAM: 256 MB
* Flash: 128MB NAND (MX30LF1G18AC)
* WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G
* Switch: 2 GbE ports MT7530
* LTE/3G: Quectel EG18-EA LTE-A Cat. 18
* SIM: 1 micro-SIM card slot
* Buttons: Reset, WPS
* LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G)
* VoIP: 1 FXS RJ11 port
* Power: 12V, 2A

UART serial console:

57600,8N1
Unpopulated header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Installation:

* Log in as root using ssh to 192.168.1.1
* scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/
* Prepare bootloader config by running:
   nvram setro uboot DebugFlag 0x1
   nvram setro uboot CheckBypass 0
   nvram commit
* Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot
* Wait for OpenWrt to boot and ssh to root@192.168.1.1
* Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image

For mode details about flashing see:
2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19)

Unsupported:

* FXS/Voice

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2023-10-29 18:51:11 +01:00
Kristian Skramstad
5e33fdfc47 qualcommax: ipq807x: add support for Netgear WAX630
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
  GND RXD TXD, beginning from the external antennas. 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet

Wlan:
* 4x4 in 2.4GHz  : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)

Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A

Mounting: Wall and ceiling
```

```
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to the console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-10-28 19:49:18 +02:00
Tianling Shen
423186d7d8 mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Glen Lee
3aef61060e
ipq806x: add support for Extreme Networks AP3935
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/

SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
       NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
        4pin Serial Header | 3.3 | GND | RX | TX

MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env

 * Installation via either RJ45 console or on-board 4 PIN header

Install Method
--------------
1) Setup TFTP server, and place
     openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
     in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
     your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
     (use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
     set bootcmd 'ping 192.168.1.1; run boot_flash'
     saveenv
8) TFTP image to RAM:
     tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
     In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
     image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin

Signed-off-by: Glen Lee <g2lee@yahoo.com>
2023-10-05 00:56:57 +02:00
Jianhui Zhao
fe10f97439 filogic: add support for GL.iNet GL-MT6000
Hardware specification:
* SoC: MediaTek MT7986A 4x A53
* Flash: 8GB EMMC
* RAM: 1GB DDR4
* Ethernet:
  * 2x2.5G RJ45 port (RTL8221B)
  * 4x1G RJ45 ports (MT7531AE)
* WLAN:
  * 2.4GHz: MT7976GN 4T4R
  * 5GHz: MT7976AN 4T4R
* Button: Reset
* LED: 1 x dual color LED
* USB: 1 x USB 3.0
* Power: DC 12V 4A
* UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC)
* JTAG: 9 PIN

If you want to use u-boot from OpenWrt, you can upgrade it safely.
* bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin
* fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip

`openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2023-09-29 00:18:26 +01:00
Elbert Mai
75ee5546e9 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-09-24 17:16:16 +02:00
Kristian Skramstad
76e419288f ipq807x: add support for Netgear WAX620
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
  Use the header closest to LED 4 and 5.
  They are marked with a white stroke.
  TX RX GND, beginning from "4". 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)

Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)

Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```

```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-09-24 13:09:16 +02:00
Piotr Dymacz
69f12c2f23 uboot-envtools: ramips: add support for ALFA Network AX1800RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-09-11 11:46:52 +02:00
Patricia Lee
907e9e0bd3 mediatek: add support for Cetron CT3003
**Hardware specification:**

- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
  | Layout:   |
  | :-------- |
  | <Antenna> |
  | VCC       |
  | GND       |
  | Tx        |
  | Rx        |

**Flash instructions:**

1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.

**Notes:**

If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.

Signed-off-by: Patricia Lee <patricialee320@gmail.com>
2023-09-08 23:17:26 +02:00
Robert Marko
96727397ef uboot-envtools: fix parallel building
Recent envtools update to 2023.07.02 has introduced a breakage when trying
to parallel build with the following error:
/bin/sh: line 1: scripts/basic/fixdep: No such file or directory

Luckily it can easily be reproduced locally via a simple script so it was
not hard to bisect it down to upstream commit [1].

However, its not that commits fault, it just uncovered an issue with the
way we have been building envtools for a long time, maybe even from the
package introduction.

The issue is that we are trying to build envtools as one of the U-Boot
no-dot-config-targets but envtools was newer a valid target for it but
since we were creating the config headers that were not actually used it
was actually building all this time.

Since the blamed commit [1] a tool called printinitialenv is built and
now a proper config is actually required in order for prerequisites to
get built properly.

So, in order to properly fix this (Hopefully for good) lets stop pretending
that envtools are a valid no-dot-config-targets target and use the
tools-only defconfig which is meant exactly for just building the tools.
This will make a minimal config for the U-Boot sandbox target and then
envtools will build just fine in parallel mode (I tested with 32 threads).
We do hovewer need to override the ARCH passed by OpenWrt and set it to
sandbox as otherwise U-Boot will not find the required headers because the
ARCH is being overriden to an incorrect one.

[1] 40b77f2a3a

Fixes: 9db0330052 ("uboot-envtools: update to 2023.07.02")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-25 23:38:11 +02:00
Stefan Agner
4af06aaf33 mediatek: filogic: wax220: cleanup device tree
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.

Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-08-22 13:37:27 +02:00
Bjørn Mork
6cc14bf66a filogic: support Telenor branded ZyXEL EX5700
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.

Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
  cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
  back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree

Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
  unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
  refuses to boot if it doesn't. The chosen "rootfs" volume must contain
  a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
  variable to the label mac.  But "factoryparams" does not always
  exist.  Instead there is a "RIP" volume containing all the factory
  data.  Copying the "RIP" volume to  "factoryparams" will fix this

Hardware
--------
SOC:   MediaTek MT7986
RAM:   1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI:  Mediatek MT7986 802.11ax 5 GHz
       Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH:   MediaTek MT7531 Switch + SoC
       3 x builtin 1G phy (lan1, lan2, lan3)
       2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB:   1 x USB 3.2 Enhanced SuperSpeed port
UART:  3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)

Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.2/24. Rename the image to C0A80101.img.

2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
   console, Interrupt the autoboot process by pressing ESC when prompted.

3. Download and boot the OpenWrt initramfs image.

   $ env set uboot_bootcount 0
   $ env set firmware nominal
   $ tftpboot
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
  OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
  not configured by OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-08-20 01:14:06 +02:00
Thomas Kupper
4d79a65d60 ipq807x: add support for Netgear RAX120v2
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.

The majority of the code is based on @jewwest's PR #11830.

Specifications:
    * CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
    * RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
    * Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
    * Ethernet: 4x 10/100/1000 Mbps LAN,
                1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
                1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
    * Wi-Fi:
        * 2.4 GHz: Qualcomm QCN5024 4x4
        * 2x 5 GHz: Qualcomm QCN5054 4x4
    * USB: 2x USB 3.0
    * LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
    * Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
    * UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
    * Power: 19 VDC, 3.1 A

Installation:
    * Flashing OpenWrt is done in two steps:
        a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
           This writes an initramfs based OpenWrt image onto the RAX120v2
        b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline

    * U-Boot allows booting an initramfs image via TFTP:
    - Set ip of your PC to 192.168.1.100
        - At the serial console interrupt boot at "Hit any key to stop autoboot:"
        - In u-boot run `tftpsrv`
        - On your PC send the OpenWrt initramfs image:

          tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb

Make 5G Aquantia phy work:
    For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
    u-boot by writing the firmware to the correct mtd partition.

    The firmware file found in the Netgear stock firmware under /lib/firmware/ named
    'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
    be converted to a MBN file.

    The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
    under 'git_home/u-boot.git/tools/mkheader.py'

    Convert the CLD file to MBN using:
    $ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn

    This MBN file can then be flashed to the MTD partition to be used by u-boot.

    The necessary files can also be found in
        https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware

    * Write MBN file to MTD partition to be loaded automatically by u-boot:

      U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
      corresponds to `/dev/mtd25` in OpenWrt.

        - find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)

          $ fgrep -i 'ethphyfw' /proc/mtd
          mtd25: 00080000 00020000 "ethphyfw

        - copy mbn file to /tmp/ folder of the router

          $ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/

        - write mbn file to ethphyfw partition

          $ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25

Revert to stock firmware:
    * Flash the stock firmware to the bootloader using TFTP/NMRP.

References to RAX120v2 GPL source:
    https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
2023-08-19 17:12:46 +02:00
Stefan Kalscheuer
9db0330052 uboot-envtools: update to 2023.07.02
Update to the latest stable version.

This update changes the default lockfile directory from /var/lock to
/run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might
not even exist, so we add a patch to revert this particular change.

[1] aeb40f1166

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
2023-08-15 16:08:55 +02:00
Ivan Pavlov
a87bc138cf uboot-envtools: add u-boot env config for Xiaomi mi-mini
Add u-boot env config for Xiaomi mi-mini for using fw_printenv and fw_setenv on this board

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
2023-08-14 20:08:05 +02:00
Hank Moretti
dcdcfc1511 mediatek: filogic: add specific layout for WR30U
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.

This layout is the same as the ubootmod layout but enabling NMBM.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-07-27 13:46:26 +02:00
Hank Moretti
20603e764d uboot-mediatek: add support for Xiaomi WR30U
Add a custom uboot build to support openwrt uboot layout.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
2023-07-27 13:41:05 +02:00
Christian Svensson
6bf0e76494 octeon: n821: add Cisco vEdge 1000 base
This is the first commit to introduce the base for the N821 board used
in Cisco vEdge 1000.

This commit does not include the custom CPLD drivers but rather
everything else that is already present in the upstream kernel.

This results in an image that boots, but e.g. the SFP ports are not
usable.

Hardware:

  - CPU: Cavium Networks CN6130, 4 cores @ 1.0 GHz
  - Flash:
    - 16 MiB SPI NOR presented as 2x8 MiB for A/B boot recovery
    - 8192 MiB eMMC
  - RAM: 4096 MiB
  - Ethernet 1Gbit ports: 1x
  - Ethernet SFP ports: 8x
  - USB ports: 2x 3.0 Type-A on front panel
  - Serial: Two, one internal and one external
  - JTAG: Yes
  - LED count: 18x
  - Button count: 1x
  - GPIOs: 1x
  - Power: 2x redundant DC 12V barrel plug
  - Extra: Slot for SD card on front

See the OpenWrt wiki for more hardware details.

Installation:

  - Flash squashfs to /dev/sda2 and put kernel on /dev/sda1.
  - Update uboot's bootcmd environment variable to match.

Full installation guide will be added to OpenWrt wiki when sysupgrade
support is added.

Signed-off-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Tommy Nevtelen <tommy@nevtelen.com>
Tested-by: Viktor Ekmark <viktor@ekmark.se>
Tested-by: Daniel Wennberg <github@networkninja.se>
2023-07-15 17:05:58 +02:00
Wenli Looi
520c9917f8 ath79: add support for ASUS RT-AC59U / ZenWiFi CD6
ASUS RT-AC59U / RT-AC59U v2 are wi-fi routers with a large number of
alternate names, including RT-AC1200GE, RT-AC1300G PLUS, RT-AC1500UHP,
RT-AC57U v2/v3, RT-AC58U v2/v3, and RT-ACRH12.

ASUS ZenWiFi AC Mini(CD6) is a mesh wifi system. The unit labeled CD6R
is the router, and CD6N is the node.

Hardware:

- SoC: QCN5502
- RAM: 128 MiB
- UART: 115200 baud (labeled on boards)
- Wireless:
  - 2.4GHz: QCN5502 on-chip 4x4 802.11b/g/n
    currently unsupported due to missing support for QCN550x in ath9k
  - 5GHz: QCA9888 pcie 5GHz 2x2 802.11a/n/ac
- Flash: SPI NOR
  - RT-AC59U / CD6N: 16 MiB
  - RT-AC59U v2 / CD6R: 32 MiB
- Ethernet: gigabit
  - RT-AC59U / RT-AC59U v2: 4x LAN 1x WAN
  - CD6R: 3x LAN 1x WAN
  - CD6N: 2x LAN
- USB:
  - RT-AC59U / RT-AC59U v2: 1 port USB 2.0
  - CD6R / CD6N: none

WiFi calibration data contains valid MAC addresses.

The initramfs image is uncompressed because I was unable to boot a
compressed initramfs from memory (gzip or lzma). Booting a compressed
image from flash works fine.

Installation:

To install without opening the case:

- Set your computer IP address to 192.168.1.10/24
- Power up with the Reset button pressed
- Release the Reset button after about 5 seconds or until you see the
  power LED blinking slowly
- Upload OpenWRT factory image via TFTP client to 192.168.1.1

Revert to stock firmware using the same TFTP method.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-08 20:19:00 +02:00
Mikhail Zhilkin
2d6784a033 ramips: add support for Sercomm S1500 devices
This commit adds support for following wireless routers:
 - Beeline SmartBox PRO (Serсomm S1500 AWI)
 - WiFire S1500.NBN (Serсomm S1500 BUC)

This commit is based on this PR:
 - Link: https://github.com/openwrt/openwrt/pull/4770
 - Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.

My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1

Common specification
--------------------
SoC:        MediaTek MT7621AT (880 MHz, 2 cores)
Switch:     MediaTek MT7530 (via SoC MT7621AT)
Wireless:   2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless:   5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet:   5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe:  via J2 on PCB, not soldered on the board
UART:       J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek

Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1

WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1

MAC address table (PRO)
-----------------------
use   address   source
LAN   *:23      factory 0x1000 (label)
WAN   *:24      factory $label +1
2g    *:23      factory $label
5g    *:25      factory $label +2

MAC addresses (NBN)
-------------------
use   address   source
LAN   *:0e      factory 0x1000
WAN   *:0f      LAN +1 (label)
2g    *:0f      LAN +1
5g    *:10      LAN +2

OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
   before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
   a. OpenWrt - that's OK, the mission accomplished
   b. Stock firmware - install Stock firmware (to switch booflag from
      Sercomm0 to Sercomm1) and then OpenWrt factory image.

Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
   reboot
2. Install stock firmware via the web OEM firmware interface

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-07-01 16:05:01 +02:00
Mathew McBride
8e7ba6fbae layerscape: remove Traverse LS1043 boards
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.

Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).

It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2023-07-01 15:47:08 +02:00
Chukun Pan
437e79ad6d uboot-mediatek: add H3C Magic NX30 Pro support
The OEM uboot limit brush into 3rd-party firmware.
So add a custom uboot build to support openwrt.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-07-01 15:13:08 +02:00
Wenli Looi
73de41898f mediatek: add support for Netgear EX6250v2 series
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.

Related: https://github.com/openwrt/openwrt/pull/5084

For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.

Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
  boot, then hold the reset button for 10 seconds. This is needed
  because sysupgrade in the stock firmware will attempt to preserve its
  configuration using sysupgrade.tgz.
  See https://github.com/openwrt/openwrt/pull/4182

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Wenli Looi
32ea8a9a7e ramips: add support for Netgear EAX12 series
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.

Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)

All LEDs and buttons appear to work without state_default.

Installation:
* Flash the factory image through the stock web interface, or TFTP to
  the bootloader. NMRP can be used to TFTP without opening the case.

Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.

References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz

* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
  DTS file for this device.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-07-01 14:42:11 +02:00
Alexey Bartenev
ce998cb6e1 ramips: add support for D-Link DIR-806A B1 router
General specification:
SoC Type: MediaTek MT7620A (580MHz)
ROM: 8 MB SPI-NOR (MX25L6406E)
RAM: 64 MB DDR (W9751G6KB-25)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Wireless: 5 GHz (MediaTek MT7610EN): ac/n
Buttons: 2 button (POWER, WPS/RESET)
Bootloader: U-Boot 1.1.3
Power: 12 VDC, 0.5 A

MACs:
| LAN	| [Factory + 0x04] - 2		|
| WLAN 2.4g	| [Factory + 0x04] - 1		|
| WLAN 5g	| [Factory + 0x8004] - 3	|
| WAN	| [Factory + 0x04] - 2		|

OEM easy installation:

1. Use a PC to browse to http://192.168.0.1.
2. Go to the System section and open the Firmware Update section.
3. Under the Local Update at the right, click on the CHOOSE FILE...
4. When a modal window appears, choose the firmware file and click on
 the Open.
5. Next click on the UPDATE FIRMWARE button and upload the firmware image.
Wait for the router to flash and reboot.

OEM installation using the TFTP method (need level converter):

1. Download the latest firmware image.
2. Set up a Tftp server on a PC (e.g. Tftpd32) and place the firmware
 image to the root directory of the server.
3. Power off the router and use a twisted pair cable to connect the PC
 to any of the router's LAN ports.
4. Configure the network adapter of the PC to use IP address 192.168.0.180
 and subnet mask 255.255.255.0.
5. Connect serial port (57600 8N1) and turn on the router.
6. Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2: Load
 system code then write to Flash via TFTP.").
7. Press Y key when show "Warning!! Erase Linux in Flash then burn new
 one. Are you sure? (Y/N)"
Input device IP (192.168.0.1) ==:192.168.0.1
Input server IP (192.168.0.180) ==:192.168.0.180
Input Linux Kernel filename () ==:firmware_name
The router should download the firmware via TFTP and complete flashing in
 a few minutes.
After flashing is complete, use the PC to browse to http://192.168.1.1 or
 ssh to proceed with the configuration.

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2023-06-25 16:25:01 +02:00
Mathew McBride
af0546da34 layerscape: armv8_64b: add Traverse Ten64 NAND variant
The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC.
It is capable of booting both standard Linux distributions
from disk devices, using EFI, and booting OpenWrt
from NAND.

See the online manual for more information, including the
flash layout[2].

This patchset adds support for generating Ten64 images
for NAND boot.
For disk boot, one can use the EFI support that was
recently added to the armvirt target.

We previously supported NAND users by building
inside our armvirt/EFI target[3], but this approach
is not suitable for OpenWrt upstream. Users who
used our supplied NAND images will be able to upgrade
to this via sysupgrade.

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] - https://www.traverse.com.au/hardware/ten64
[2] - https://ten64doc.traverse.com.au/hardware/flash/
[3] - Example:
285e4360e1
2023-06-25 16:02:19 +02:00
Maximilian Martin
906e2a1b99 ath79: Add support for MOXA AWK-1137C
Device specifications:
======================

* Qualcomm/Atheros AR9344
* 128 MB of RAM
* 16 MB of SPI NOR flash
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4/5 GHz Wi-Fi
* 4x GPIO-LEDs (1x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* 2x fast ethernet
  - lan1
    + builtin switch port 1
    + used as WAN interface
  - lan2
    + builtin switch port 2
    + used as LAN interface
* 9-30V DC
* external antennas

Flashing instructions:
======================

Log in to https://192.168.127.253/
   Username: admin
   Password: moxa

Open Maintenance > Firmware Upgrade and install the factory image.

Serial console access:
======================

Connect a RS232-USB converter to the maintenance port.
   Pinout: (reset button left) [GND] [NC] [RX] [TX]

Firmware Recovery:
==================

When the WLAN and SYS LEDs are flashing, the device is in recovery mode.

Serial console access is required to proceed with recovery.

Download the original image from MOXA and rename it to 'awk-1137c.rom'.
Set up a TFTP server at 192.168.127.1 and connect to a lan port.

Follow the instructions on the serial console to start the recovery.

Signed-off-by: Maximilian Martin <mm@simonwunderlich.de>
2023-06-25 12:59:26 +02:00
Mikhail Zhilkin
e4fe3097ef mediatek: add support for Mercusys MR90X v1
This commit adds support for Mercusys MR90X(EU) v1 router.

Device specification
--------------------
SoC Type:   MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM:        MediaTek MT7986BLA (512MB)
Flash:      SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet:   MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet:   1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g:    MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g:    MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs:       1 orange and 1 green status LEDs, 4 green gpio-controlled
            LEDs on ethernet ports
Button:     1 (Reset)
USB ports:  No
Power:      12 VDC, 2 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
            slots contain "seconduboot" (also U-Boot 2022.01-rc4)

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |
    +--- Don't connect

The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.

Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Once inside OpenWrt, set / update env variables:
      fw_setenv baudrate 115200
      fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
      fw_setenv fdtcontroladdr 5ffc0e70
      fw_setenv ipaddr 192.168.1.1
      fw_setenv loadaddr 0x46000000
      fw_setenv mtdids "spi-nand0=spi-nand0"
      fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
      fw_setenv netmask 255.255.255.0
      fw_setenv serverip 192.168.1.2
      fw_setenv stderr serial@11002000
      fw_setenv stdin serial@11002000
      fw_setenv stdout serial@11002000
      fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Installation (without UART)
---------------------------
1.  Login as root via SSH (router IP, port 20001, password - your web
    interface password)
2.  Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
    SSH settings from the p.1)
3.  Add a newline after "#!/bin/sh":
       telnetd -l /bin/login.sh
4.  Save "65-iptv" file
5.  Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
    save
6.  Make sure that telnetd is running:
       netstat -ltunp | grep 23
7.  Login via telnet to router IP, port 23 (no username and password are
    required)
8  Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
    router (e.g., using WinSCP and SSH settings from the p.1)
9.  Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
    download and upload the full version of busybox to the router. For
    example, from here:
    https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
    Upload busybox-arm64 to the /tmp dir of the router and run:
    in the telnet shell:
       cd /tmp
       chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
       du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
    (greater than "initramfs-kernel.bin" size):
       ubirmvol /dev/ubi0 -N kernel
       ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
       ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
    already exists) with the necessary values:
       fw_setenv baudrate 115200
       fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
       fw_setenv fdtcontroladdr 5ffc0e70
       fw_setenv ipaddr 192.168.1.1
       fw_setenv loadaddr 0x46000000
       fw_setenv mtdids "spi-nand0=spi-nand0"
       fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
       fw_setenv netmask 255.255.255.0
       fw_setenv serverip 192.168.1.2
       fw_setenv stderr serial@11002000
       fw_setenv stdin serial@11002000
       fw_setenv stdout serial@11002000
       fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
       reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
       sysupgrade -n /tmp/sysupgrade.bin

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
   upload the OEM firmware

Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
   etc.)

Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"

ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot   Vol ID: 0|
| Volume Name: kernel  Vol ID: 1|
| Volume Name: rootfs  Vol ID: 2|
+-------------------------------+

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| label   | 00:eb:xx:xx:xx:be | label     |
| LAN     | 00:eb:xx:xx:xx:be | label     |
| WAN     | 00:eb:xx:xx:xx:bf | label+1   |
| WLAN 2g | 00:eb:xx:xx:xx:be | label     |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1   |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-06-25 12:25:22 +02:00
David Bauer
1b467a902e ath79: add support for Aruba AP-115
Hardware
========

CPU   Qualcomm Atheros QCA9558
RAM   256MB DDR2
FLASH 2x 16M SPI-NOR (Macronix MX25L12805D)
WIFI  Qualcomm Atheros QCA9558
      Atheros AR9590

Installation
============

1. Attach to the serial console of the AP-105.
   Interrupt autoboot and change the U-Boot env.

   $ setenv rb_openwrt "setenv ipaddr 192.168.1.1;
     setenv serverip 192.168.1.66;
     netget 0x80060000 ap115.bin; go 0x80060000"
   $ setenv fb_openwrt "bank 1;
     cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000"
   $ setenv bootcmd "run fb_openwrt"
   $ saveenv

2. Load the OpenWrt initramfs image on the device using TFTP.
   Place the initramfs image as "ap105.bin" in the TFTP server
   root directory, connect it to the AP and make the server reachable
   at 192.168.1.66/24.

   $ run rb_openwrt

3. Once OpenWrt booted, transfer the sysupgrade image to the device
   using scp and use sysupgrade to install the firmware.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-06-23 00:20:56 +02:00
Flole Systems
984786a2f7 filogic: add support for Netgear WAX220
Hardware
--------
SOC:   MediaTek MT7986
RAM:   1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI:  Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH:   Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART:  3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)

Installation
------------

1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
   interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.

   $ setenv ipaddr 192.168.2.1
   $ setenv serverip 192.168.2.2
   $ tftpboot openwrt.bin
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
2023-06-21 23:32:26 +02:00
Robert Marko
83314c13d0
qualcommax: move ipq807x support to subtarget
Now that qualcommax exists as a target and dependencies have been updated
let move ipq807x support to subtarget of qualcommax.

This is mostly copy/paste with the exception of having to update SSDK and
NSS-DP to use CONFIG_TARGET_SUBTARGET.

This is a preparation for later addition of IPQ60xx and IPQ50xx support.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-06-16 11:11:09 +02:00