FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Ubiquiti WA devices with newer hw version (sold 2023)
require UBNT_VERSION to be at least 8.7.4, otherwise
the image is rejected.
For consistency, also increase version number for XC devices.
Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Disabled services should be kept disabled after sysupgrade. This can be
easily handled using a proper uci-defaults script.
Extend sysupgrade to check for disabled services, generate uci-defaults
script disabling them and include it in backup.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Setting overlay while creating backup allows including extra files in
archive without actually writing them to flash. Right now this feature
is limited to /etc/backup/ directory and is used only for including
installed_packages.txt.
Extend this solution to make it more generic:
1. Always mount overlay while creating backup
2. Overlay whole / to don't limit it to /etc/backup/
This allows including any additional files in backups and adding more
sysupgrade features.
Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When tar was failing, it was exiting immediately. Some files and the
tmpfs mount (-k) would remain breaking the next backup attempt.
Also remove redundant $? from exit builtin call as exit already returns
the last command exit code when called.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
tar stderr was probably discarded only to remove this message:
tar: removing leading '/' from member names
However, together with that, any other error would also be discarded.
It is easier to fix that allowing the error message to be printed.
In sysupgrade, the backup file list only uses absolute paths. That way,
the solution is to remove the leading '/' from all files (sed) and chdir
to / (option -C /)
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Fix style of nvmem cell names in the device tree of the GL.iNet MT-2500.
Fixes: 49ed52b862 ("mediatek: filogic: convert GL.iNet MT-2500 to use NVMEM-on-MMC)"
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Recent OEM firmware versions test the version number embedded in the uimage
"name" header field. The exact restricton is unknown, but "7.0.8.4" seems
to be the lowest number accepted on a GS110TPPv1 which already has that
version or higher.
A "9.9.9.9" version is accepted as valid by the GS110TPPv1 OEM firmware,
and considered both unique enough to identify an OpenWrt image and
moderately future proof against OEM version bumps.
This change is also boot tested on a GS108Tv3 with
"BOOT Loader Version 1.0.0.2 (2018-08-31 17:05:26 UTC)"
to verify that it doesn't break boot on older hardware.
Link: https://forum.openwrt.org/t/72510/58
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Import patch to make sure SGM_REG_SEL clock is always enabled as it
seems that more registers than just SGMIISYS0 and SGMIISYS1 are
depending on that clock being enabled.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we can reference MMC partitions in device tree, use that
to get rid of Wi-Fi EEPROM and MAC address setup in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use device_set_node to make sure OF node gets assigned on block
devices to be used as NVMEM providers. While block partitions were
already working fine as NVMEM providers, bare block devices such as
mmcblk0boot1 will not work without this change.
Fixes: fc153aa8d9 ("kernel: import pending patches adding support for NVMEM on UBI and MMC")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
UNIPHY2 on the WAX630 is connected to a QCA8081 PHY which is only 2.5G and
it does not support using USXGMII at all but rather only SGMII or SGMII+.
Tested-by: Kristian Skramstad <kristian+github@83.no>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove inaccurate compatible string 'mediatek,mt7986-ethsys' which
results in the wrong clock driver probing on MT7981 with Linux 6.1 and
ends up freezing the system once WED is used.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
Since this is not Qnap 301W specific lets fix it subtarget wide by
declaring the correct PHY mode for 10G AQR-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Interfaces that have AQR-s attached to them are using USXGMII and not just
the default SGMII.
This was fine until SSDK added some sanity checking and now on Qnap 301W it
would fail with:
[ 24.740197] nss-dp 3a001800.dp5 10g-1 (uninitialized): failed to connect to phy device
[ 24.740264] nss-dp: probe of 3a001800.dp5 failed with error -14
So, lets fix 10G AQR ports by declaring the correct PHY mode.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Also here build fails due to increased kernel size.
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Due to increased kernel size the build currently fails if including
the MT7622 rfb1 (UBI). Skip it for now until there is a better
solution (such as replacing the bootloader and changing the flash
layout).
Fixes: da970d63fb ("mediatek: switch to Linux version 6.1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include the needed Ethernet PHY driver module for the BananaPi R3 mini.
Fixes: b03d3644cf ("mediatek: filogic: add BananaPi BPi-R3 mini")
Reported-by: BPI forum user nezar_taima
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let ubinize-image append the ubinized image to the existing image
instead of replacing it.
Fixes: 6c17d71973 ("scripts: ubinize-image.sh: support static volumes, make size optional")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
One of the pins requiered by M.2 slot is conflict with spi1,
however, spi1 seems unused so simply disable it for now, this
matches the factory behavior [1].
1. 9bd78779f2
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Conversion to new LED color/function format and drop label format.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property can be
removed in favor of the new format.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This commit fixes the alphabetical order in 02_network.
The 2 deco devices in ath79_setup_interfaces() were in the wrong place.
Signed-off-by: Foica David <superh552@gmail.com>
Since we can configure the PHY LED of the qca8081,
add a configuration for this device.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The dts of Arcadyan AW1000 forgot to convert qca807x PHY
to PHY package implementation. This commit fix it.
Fixes: 0ab4b92 ("qualcommax: convert qca807x PHY to PHY package implementation")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Reviewed-by: Robert Marko <robimarko@gmail.com>
