Commit Graph

29002 Commits

Author SHA1 Message Date
Rafał Miłecki
585360f0c0 gemini: refresh kernel config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-07 13:39:40 +01:00
Rafał Miłecki
f784fe88a6 sifiveu: refresh kernel config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-07 13:39:40 +01:00
Rafał Miłecki
34dbd02c12 qoriq: refresh kernel config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-07 13:39:40 +01:00
Rafał Miłecki
f6e35efbfe bcm53xx: refresh kernel config for 6.1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-06 13:25:59 +01:00
David Bauer
ae500e62e2 mediatek: add label-mac for GL.iNet GL-MT3000
The MAC-address of gmac0 matches the one printed on the bottom label.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-03 23:06:33 +01:00
Łukasz M
5a603c7a31 mediatek: mt7981: improve fan behaviour
This doubles the number of cooling-levels.
In addition the fan is turned on with a low speed at lower temperatures
and with a higher speed at higher temperatures.
This also attempts to reduce the likelihood of constant start-stop actions.

The change only affects the GL.iNet MT3000 and has been tested with it.

Signed-off-by: Łukasz M <lukasz1992m@gmail.com>
2023-11-03 23:06:07 +01:00
Lech Perczak
0c47bdb902 ath79: support Fortinet FAP-220-B
Fortinet FAP-220-B is a dual-radio, dual-band 802.11n enterprise managed
access point with PoE input and single gigabit Ethernet interface.

Hardware highlights:
Power: 802.3af PoE input on Ethernet port, +12V input on 5.5/2.1mm DC jack.
SoC: Atheros AR7161 (MIPS 24kc at 680MHz)
RAM: 64MB DDR400
Flash: 16MB SPI-NOR
Wi-Fi 1: Atheros AR9220 2T2R 802.11abgn (dual-band)
Wi-Fi 2: Atheros AR9223 2T2R 802.11bgn (single-band)
Ethernet: Atheros AR8021 single gigabit Phy (RGMII)
Console: External RS232 port using Cisco 8P8C connector (9600-8-N-1)
USB: Single USB 2.0 host port
LEDs: Power (single colour, green), Wi-Fi 1, Wi-Fi 2, Ethernet, Mode, Status
(dual-colour, green and yellow)
Buttons: reset button hidden in bottom grill,
  in the top row, 2nd column from the right.
Label MAC address: eth0

FCC ID: TVE-220102

Serial port pinout:
3 - TxD
4 - GND
6 - RxD

Installation: The same methods apply as for already supported FAP-221-B.

For both methods, a backup of flash partitions is recommended, as stock firmware
is not freely available on the internet.

(a) Using factory image:

1. Connect console cable to the console port
2. Connect Ethernet interface to your PC
3. Start preferred terminal at 9600-8-N-1
4. Have a TFTP server running on the PC.
5. Put the "factory" image in TFTP root
6. Power on the device
7. Break boot sequence by pressing "Ctrl+C"
8. Press "G". The console will ask you for device IP, server IP, and filename.
   Enter them appropriately.
   The defaults are:
   Server IP: 192.168.1.1 # Update accordingly
   Device IP: 192.168.1.2 # Update accordingly
   Image file: image.out # Use for example: openwrt-ath79-generic-fortinet_fap-220-b-squashfs-factory.bin
9. The device will load the firmware over TFTP, and verify it. When
   verification passes, press "D" to continue installation. The device
   will reboot on completion.

(b) Using initramfs + sysupgrade
1. Connect console cable to the console port
2. Connect Ethernet interface to your PC
3. Start preferred terminal at 9600-8-N-1
4. Have a TFTP server running on the PC.
5. Put the "initramfs" image in TFTP root
6. Power on the device.
7. Break boot sequence by pressing "Ctrl+C"
8. Enter hidden U-boot shell by pressing "K". The password is literal "1".
9. Load the initramfs over TFTP:

   > setenv serverip 192.168.1.1 # Your PC IP
   > setenv ipaddr 192.168.1.22 # Device IP, both have to share a subnet.
   > tftpboot 81000000 openwrt-ath79-generic-fortinet_fap-220-b-initramfs-kernel.bin
   > bootm 81000000

10. (Optional) Copy over contents of at least "fwconcat0", "loader", and "fwconcat1"
    partitions, to allow restoring factory firmware in future:

    # cat /dev/mtd1 > /tmp/mtd1_fwconcat0.bin
    # cat /dev/mtd2 > /tmp/mtd2_loader.bin
    # cat /dev/mtd3 > /tmp/mtd3_fwconcat1.bin

    and then SCP them over to safety at your PC.

11. When the device boots, copy over the sysupgrade image, and execute
    normal upgrade:

    # sysupgrade openwrt-ath79-generic-fortinet_fap-220-b-squashfs-sysupgrade.bin

Return to stock firmware:
1. Boot initramfs image as per initial installation up to point 9
2. Copy over the previously backed up contents over network
3. Write the backed up contents back:

   # mtd write /tmp/mtd1_fwconcat0.bin fwconcat0
   # mtd write /tmp/mtd2_loader.bin loader
   # mtd write /tmp/mtd3_fwconcat1.bin fwconcat1

4. Erase the reserved partition:

   # mtd erase reserved

5. Reboot the device

Quirks and known issues:
- The power LED blinking pattern is disrupted during boot, probably due
  to very slow serial console, which prints a lot during boot compared
  to stock FW.
- "mac-address-ascii" device tree binding cannot yet be used for address
  stored in U-boot partition, because it expects the colons as delimiters,
  which this address lacks. Addresses found in ART partition are used
  instead.
- Due to using kmod-owl-loader, the device will lack wireless interfaces
  while in initramfs, unless you compile it in.
- The device heats up A LOT on the bottom, even when idle. It even
  contains a warning sticker there.
- Stock firmware uses a fully read-write filesystem for its rootfs.
- Stock firmware loads a lot of USB-serial converter drivers for use
  with built-in host, probably meant for hosting modem devices.
- U-boot build of the device is stripped of all branding, despite that
  evidence of it (obviously) being U-boot can be found in the binary.
- The user can break into hidden U-boot shell using key "K" after
  breaking boot sequence. The password is "1" (without quotes).
- Telnet is available by default, with login "admin", without password.
  The same is true for serial console, both drop straight to the Busybox
  shell.
- The web interface drops to the login page again, after successfull
  login.
- Whole image authentication boils down to comparing a device ID against
  one stored in U-boot.
- And this device is apparently made by a security company.

Big thanks for Michael Pratt for providing support for FAP-221-B, which
shares the entirety of image configuration with this device, this saved
me a ton of work.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-11-03 23:06:07 +01:00
Lech Perczak
6c12c88d2e ath79: image: extract common part for Fortinet FAP series
In preparation for FAP-220-B support, extract the common part of image
recipe for FAP-221-B.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-11-03 23:06:07 +01:00
Lech Perczak
c6a090dbf6 ath79: dts: fortinet_loader: extract common part
In preparation for FAP-220-B support, rename ar934x_fortinet_loader.dtsi
to arxxxx_fortinet_loader.dtsi, to avoid confusion, as FAP-220-B shares
flash layout with FAP-221-B exactly despite different SoC.

While at that, add a label to U-boot partition to allow for nvmem MAC
binding in future.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2023-11-03 23:06:07 +01:00
Mikhail Zhilkin
45a50a06fb treewide: fix MERCUSYS brand spelling
This commit fixes MERCUSYS brand spelling. The proper name is capitalized.

Link: https://www.mercusys.com/
Link: https://github.com/torvalds/linux/blob/master/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c#L7779

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-03 23:06:07 +01:00
Patryk Kowalczyk
0c3f4bd85e filogic: fix wifi eeprom filename for tuf-ax6000
The router use mt7986_eeprom_mt7976_dual.bin

Fixes: d522ccecb2 ("filogic: add support for ASUS TUF AX6000")

Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
2023-11-03 23:06:07 +01:00
Daniel Golle
bc335f2967 ramips: add support for MeiG SLT866 4G CPE
Hardware:
 - SoC: Mediatek MT7621 (MT7621AT)
 - Flash: 32 MiB SPI-NOR (Macronix MX25L25635E)
 - RAM: 128 MiB
 - Ethernet: Built-in, 2 x 1GbE
 - 3G/4G Modem: MEIG SLM828 (currently only supported with ModemManager)
 - SLIC: Si32185 (unsupported)
 - Power: 12V via barrel connector
 - Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
 - Wifi 5GHz: Mediatek MT7613BE 802.11ac/n/a
 - LEDs: 8x (7 controllable)
 - Buttons: 2x (RESET, WPS)

Installing OpenWrt:
 - sysupgrade image is compatible with vendor firmware.

Recovery:
 - Connect to any of the Ethernet ports, configure local IP:
   10.10.10.3/24 (or 192.168.10.19/24, depending on OEM)
 - Provide firmware file named 'mt7621.img' on TFTP server.
 - Hold down both, RESET and WPS, then power on the board.
 - Watch network traffic using tcpdump or wireshark in realtime to
   observe progress of device requesting firmware. Once download has
   completed, release both buttons and wait until firmware comes up.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-03 21:16:29 +00:00
Daniel Golle
7db87d7c68 kernel: support reading hex MAC address from NVMEM
In addition to binary and ASCII-formatted MAC addresses, add support
for processing hexadecimal encoded MAC addresses from NVMEM.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-03 21:16:29 +00:00
Daniel Golle
f32baf6a65 kernel: add support MeigLink SLM828 modem
Another Qualcomm-based USB-connected modem, offering endpoints
 0 : rndis_host (link to voip subsystem listening on 169.254.5.100)
 1 : rndis_host (?)
 2 : option (?)
 3 : option (at)
 4 : option (at)
 5 : option (?)
 6 : GobiNet (qmi)
 7 : ?

Add support for this modem in rndis_host, option and qmi_wwan driver
which allows the modem to be used with ModemManager.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-03 21:16:29 +00:00
John Audia
7285f7744f kernel: bump 6.1 to 6.1.61
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.61

Removed upstreamed:
  generic/backport-6.1/814-v6.6-0018-nvmem-imx-correct-nregs-for-i.MX6SLL.patch[1]
  generic/backport-6.1/814-v6.6-0019-nvmem-imx-correct-nregs-for-i.MX6UL.patch[2]
  generic/backport-6.1/814-v6.6-0020-nvmem-imx-correct-nregs-for-i.MX6ULL.patch[3]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.61&id=b90b8633ef62314f3a5f5675106e6dcdec981b6f
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.61&id=37495846b1efc23c1767b17ddd6645cc0ccb9946
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.61&id=116671d25915b913374ccdb2956b5fdaff939dc9

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-11-03 13:02:30 +01:00
Mikhail Zhilkin
1cb85e1251
ramips: fix wrong permissions on dts files
This commit fixes wrong permissions on dts files. Before the commit these
dts files are executable:
   -rwxrwxr-x mt7620a_dlink_dir-806a-b1.dts
   -rwxrwxr-x mt7621_wavlink_wl-wn573hx1.dts

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-11-02 20:42:53 +01:00
Robert Marko
5cdf152b28
qualcommax: ipq807x: move subtarget specific kernel options
Currently, qualcommax target contains the full kernel config for the
ipq807x subtarget, but since I am working on ipq60xx as well it makes
sense to split out the ipq807x specific kernel options to subtarget
config.

ipq60xx will use the same approach and use subtarget config.

Should result in the same end kernel config, verified by comparing the
generated kernel .config.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-11-02 20:25:33 +01:00
Rafał Miłecki
943bd3c9f6 bcm53xx: add the latest fix version of brcm_nvram
It was just sent for upstream.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-11-02 09:23:44 +01:00
Til Kaiser
3004c20614 x86: add support for Mellanox Spectrum SN2000 Switches
The Mellanox Spectrum SN2000 Series Switches are Managed Ethernet
Switches with a maximum speed of 100Gb/s and up to 56 ports.

Tested on a Mellanox Spectrum SN2100 with the following specs:
 - CPU: Intel ATOM x86 dual-core 2.4GHz
 - RAM: 8GB
 - Disk: 16GB SSD
 - Ports: 16x QSFP28 100GbE, 1x 100M Mgmt Port, 1x RJ45 Serial Port
 - USB: 1x mini 2.0
 - Button: 1x (reset)
 - LEDs: 6x

Installation:
 - Create a bootable USB device (either by flashing this image
   onto it or another Linux distribution)
 - Unzip the generic OpenWrt x64 image
   and copy it onto the USB device
 - Plug the USB device into the Mellanox Switch and boot from it
 - Flash the image (e.g., with dd) onto the internal SSD
   of the switch (should be /dev/sda)

To enter the BIOS, reboot the switch and press CTRL+B while you see
the BIOS information text (American Megatrends …). The default password
to enter the BIOS is admin. To boot from the USB device, switch to the
Boot index tab and set your USB device at the top of the boot order
(the internal SSD should be currently there). Don't forget to set
the SSD back at the top after you have flashed the image.

Signed-off-by: Til Kaiser <til.kaiser@gmx.de>
[unify with generic x64 image]
Signed-off-by: David Bauer <mail@david-bauer.net>
2023-10-31 21:12:15 +01:00
Patryk Kowalczyk
d522ccecb2 filogic: add support for ASUS TUF AX6000
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1

Installation
============

Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.

Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.

yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.

You can see three holes
From Bottom: RX, TX, Ground - partially covered

Download & Boot the OpenWrt initramfs image.

In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000

In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:

Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.

$ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
================

2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected

The cover yellow light is not supported. (only blue one)

Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
2023-10-31 21:12:15 +01:00
Rafał Miłecki
c997634c01 kernel: fix mtd/NVMEM regression affecting U-Boot env NVMEM driver
Fixes: b595670070 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
Fixes: https://github.com/openwrt/openwrt/issues/13831
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-31 17:33:28 +01:00
INAGAKI Hiroshi
c441f9b2c5 mvebu: add support for IIJ SA-W2
Internet Initiative Japan Inc. (IIJ) SA-W2 is a network appliance with
11ac (Wi-Fi 5) wlan, based on 88F6810.

Specification:

- SoC         : Marvell Armada 380 88F6810
- RAM         : DDR3 256 MiB (Micron MT41K64M16TW-107:J x2)
- Flash       : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN        : 2.4/5 GHz, Mini PCI-E
  - 2.4 GHz   : Silex SX-PCEGN (Atheros AR9287 (2T2R))
  - 5 GHz     : Silex SX-PCEAC (Qualcomm Atheros QCA9880 (3T3R))
- Ethernet    : 10/100/1000 Mbps x5
  - Switch    : Marvell 88E6172
- LEDs/Keys   : 12x/1x
- UART        : "CONSOLE" port (RJ-45, RS-232C)
  - settings  : 115200n8
  - assignment: 1:NC,  2:NC,  3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC,  8:NC
  - note      : compatible with Cisco console cable
- Power       : DC Input or PoE
  - DC Input  : 12 VDC, 3 A
  - PoE       : 802.3af
    - module  : Silvertel Ag9712-2BR
    - note    : USB ports shouldn't be used when powered by PoE
- Bootloader  : PMON2000 based
- Stock       : NetBSD based

Flash instruction using sysupgrade image:

1. Prepare TFTP server with IP address 192.168.0.10 and put sysupgrade
   image to TFTP directory
2. Connect PC to "GE0/PoE" port on SA-W2
3. Power on SA-W2, interrupt count-down by Esc and enter to bootloader
   CLI
4. Set IP address of the device

   address 192.168.0.1

5. Download sysupgrade image and flash to storage

   tftpload 192.168.0.10 <image name>
   firmwrite

   example:

   #tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
   Loading openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
   loaded 8127268 byte(s)
   #firmwrite
   Erasing FLASH block  32 Done 0x00200000.
   Erasing FLASH block  33 Done 0x00210000.
   ...
   Erasing FLASH block 155 Done 0x009b0000.
   Erasing FLASH block 156 Done 0x009c0000.
   Programming FLASH. Done.
   Verifying FLASH. No Errors found.

6. Check the flashed firmware

   firmcheck

   example:

   #firmcheck
   [Normal firmware]
   ident: 'SEIL2015'
   copyright: 'ARM OpenWrt Linux-5.15.93'
   version format: 1
   version major: 9
   version minor: 99
   version release: 'r22060+36-5163bb5e54'
   body size: 3578524
   checksum: 0x8a083cb8

   [Rescue firmware]
   ident: 'SEIL2015'
   copyright: 'Copyright (c) 2017 Internet Initiative Japan Inc. All rights reserved.'
   version format: 1
   version major: 3
   version minor: 70
   version release: 'Release'
   body size: 10152458
   checksum: 0x8f9518c2

7. Boot with the flashed firmware

   boot

Note:

- The bootloader on this device is not U-Boot and it's environment space
  ("bootloader-env") has no compatibility with U-Boot tools.

- eth1 is connected to port6 of 88E6172 switch, but multi-cpu port can't
  be handled on Linux Kernel and not defined.

- Powering by PoE hasn't been tested yet.

- This device has 2x OS images on flash and they can be switched by
  setting "BOOTDEV" variable on bootloader CLI.
  That variable supports the following values:

  - "flash" : primary image on flash ("firmware")
  - "rescue": secondary image on flash ("rescue")
  - "usb"   : usb storage (broken?)
  - "lan0/1": network

  command to set:

  set BOOTDEV=<dev>

  example:

    set BOOTDEV=rescue

  This commit also supports booting from secondary partition.

- To execute initramfs image on bootloader CLI, use "go" command.
  ("go" command is not listed on the output of "help", but available)

  example (download and execute):

    address 192.168.0.1
    tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-initramfs-kernel.bin
    go

MAC addresses:

LAN    : 00:E0:4D:xx:xx:19 (none)
WAN    : 00:E0:4D:xx:xx:18 (board_info, 0x6 (hex))
2.4 GHz: 84:25:3F:xx:xx:xx (Mini PCI-E card)
5 GHz  : 84:25:3F:xx:xx:xx (Mini PCI-E card)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-31 14:02:01 +01:00
INAGAKI Hiroshi
49f55b17f0 mvebu: cortexa9: enable seil-fw mtdsplit driver
Enable seil-fw driver on mvebu/cortexa9 to use it on IIJ SA-W2.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-31 14:02:01 +01:00
INAGAKI Hiroshi
c6e71b34b2 kernel: add seil-fw mtdsplit driver for IIJ SEIL devices
This mtdsplit parser driver parses firmware partition on Internet
Initiative Japan Inc. (IIJ) SEIL series devices.

Structure of header:

  0x0 - 0x7 : Identifier            (hex)
  0x8 - 0x57: Copyright             (ascii)
 0x58 - 0x5b: Data CRC              (hex)
 0x5c - 0x5f: Image Format Version  (hex)
 0x60 - 0x63: Image Major Version   (hex)
 0x64 - 0x67: Image Minor Version   (hex)
 0x68 - 0x87: Image Release Version (ascii)
 0x88 - 0x8b: Xor value for Data?   (hex)
 0x8c - 0x8f: Data Length           (hex)

Properties:

- compatible      : "iij,seil-firmware"
- iij,seil-id     : ID of SEIL firmware for the device (8 bytes)
  - examples:
    - SA-W2       : <0x5345494c 0x32303135> ("SEIL2015")
    - SEIL/X1     : <0x5345494c 0x2F582020> ("SEIL/X  ")
- iij,bootdev-name: boot device name assigned to the partition
                    (optional)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-31 14:02:01 +01:00
Mikhail Zhilkin
7666940efe ramips: enable wireless LEDs activity blinking for TP-Link EC330-G5u v1
This commit enables wireless LEDs activity blinking for TP-Link EC330-G5u
v1 router.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-10-31 13:56:58 +01:00
Weiping Yang
c7baca3bb6 ath79: add support for GL.iNet GL-S200
Specifications:
SoC: QCA9531(650MHz)
RAM: DDR2 128M
Flash: SPI NOR 16M + SPI NAND 128M
WiFi: 2.4GHz with 2 antennas(WiFi/Thread)
Ethernet:
    1xLAN(10/100M)
    2xWAN(10/100M)
Button: 1x Reset Button
Switch: 1x Mode switch
LED: 1x Blue LED + 1x White LED + 1x Orange LED
IOT: Thread + ZigBee/Zwave

By uboot web failsafe:
Push the reset button for 5 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2023-10-31 13:53:11 +01:00
Shiji Yang
e32f70e706 ath79: increase the rfkill debounce interval for TP-Link Archer C7 v2
Due to circuit issue or silicon defect, sometimes the WiFi switch button
of the Archer C7 v2 can be accidentally triggered multiple times in one
second. This will cause WiFi to be unexpectedly shut down and trigger
'irq 23: nobody cared'[1] warning. Increasing the key debounce interval
to 1000 ms can fix this issue. This patch also add the missing rfkill
key label.

[1] Warning Log:
```
[87765.218511] irq 23: nobody cared (try booting with the "irqpoll" option)
[87765.225331] CPU: 0 PID: 317 Comm: irq/23-keys Not tainted 5.15.118 #0
...
[87765.486246] handlers:
[87765.488543] [<85257547>] 0x800c29a0 threaded [<5c6328a2>] 0x80ffe0b8 [gpio_button_hotplug@4cf73d00+0x1a00]
[87765.498364] Disabling IRQ #23
```

Fixes: https://github.com/openwrt/openwrt/issues/13010
Fixes: https://github.com/openwrt/openwrt/issues/12167
Fixes: https://github.com/openwrt/openwrt/issues/11191
Fixes: https://github.com/openwrt/openwrt/issues/7835

Tested-by: Hans Hasert
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-29 23:07:43 +01:00
Shiji Yang
f025135f16 ramips: fix Gigabit Ethernet port of the HiWiFi HC5861
HiWiFi HC5861 has a GbE port which connected to the RTL8211E PHY
chip. This patch adds the missing Realtek PHY driver package and
sets the correct external PHYs base address to make it work again.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-29 22:49:35 +01:00
Milan Krstic
17465fc77e ramips: add support for ZyXEL LTE5398-M904
ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS
port.

Specifications:

* SoC: Mediatek MT7621AT
* RAM: 256 MB
* Flash: 128MB NAND (MX30LF1G18AC)
* WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G
* Switch: 2 GbE ports MT7530
* LTE/3G: Quectel EG18-EA LTE-A Cat. 18
* SIM: 1 micro-SIM card slot
* Buttons: Reset, WPS
* LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G)
* VoIP: 1 FXS RJ11 port
* Power: 12V, 2A

UART serial console:

57600,8N1
Unpopulated header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Installation:

* Log in as root using ssh to 192.168.1.1
* scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/
* Prepare bootloader config by running:
   nvram setro uboot DebugFlag 0x1
   nvram setro uboot CheckBypass 0
   nvram commit
* Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot
* Wait for OpenWrt to boot and ssh to root@192.168.1.1
* Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image

For mode details about flashing see:
2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19)

Unsupported:

* FXS/Voice

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2023-10-29 18:51:11 +01:00
Felix Fietkau
cea62f45cc kernel: fix compile issues with tools/ on macOS
Reduce dependencies on linux specific header files.
Avoid using __weak for function declarations

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-10-29 15:57:25 +01:00
Florian Maurer
b3d2008f92
qualcommax: only build initramfs if CONFIG_TARGET_ROOTFS_INITRAMFS is set
This makes it possible to build the ipq807x netgear-wax218 without initramfs - which is required for downstream projects (gluon)

Signed-off-by: Florian Maurer <f.maurer@outlook.de>
2023-10-29 11:35:46 +01:00
Robert Marko
4b7b3b9777
qualcommax: mark upstreamed patches as such
The GPLL fixes were merged upstream, so lets mark them as such.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-10-29 11:34:53 +01:00
Matt Merhar
b2068f4aac kernel: fix jffs2 compilation with GCC_PLUGIN_RANDSTRUCT enabled
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:

./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]

This was originally applied via 55643e469c, but was unintentionally
reverted in 483503603c.

Fixes: 483503603c ("generic: 5.15: rework pending patch")
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
2023-10-28 21:17:16 -04:00
INAGAKI Hiroshi
b7c12a9bfc mvebu: add support for Fortinet FortiGate 30E
Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 5x 10/100/1000 Mbps
  - Switch     : Marvell 88E6176
- LEDs/Keys    : 16x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Modex 5557-02R

Flash instruction using initramfs image:

 1. Power on FG-30E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "r" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex))
WAN   : 70:4C:A5:xx:xx:CF
LAN 1 : 70:4C:A5:xx:xx:D0
LAN 2 : 70:4C:A5:xx:xx:D1
LAN 3 : 70:4C:A5:xx:xx:D2
LAN 4 : 70:4C:A5:xx:xx:D3

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-10-29 02:12:38 +02:00
Kristian Skramstad
5e33fdfc47 qualcommax: ipq807x: add support for Netgear WAX630
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
  GND RXD TXD, beginning from the external antennas. 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet

Wlan:
* 4x4 in 2.4GHz  : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)

Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A

Mounting: Wall and ceiling
```

```
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to the console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-10-28 19:49:18 +02:00
Kristian Skramstad
f9f2c8ef05 qualcommax: ipq807x: alphabetically sort Netgear WAX family.
As requested by the maintainers, the order for the WAX family
should be alphabetically. WAX620 is now after WAX218.

Files changed:
+ipq807x.mk
+01_leds

No changes to the content.

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-10-28 19:48:57 +02:00
Tianling Shen
423186d7d8 mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Chukun Pan
00e3447926 sunxi: enable cpufreq driver for H6 SoC
Allwinner H6 needs this driver to enable DVFS support.
May also be used with H616/H618 SoC in the future.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-10-28 18:31:43 +02:00
Chukun Pan
b25c7548e0 sunxi: fixes led for nanopi boards
Kernel 5.15 already supports the NanoPi R1 and NanoPi R1S H5,
and they use new LED bindings that do not match the existing
settings in 01_leds. Update led settings to fixes that.

List the led node on NanoPi R1S H5:
root@OpenWrt:~# ls /sys/class/leds/
green:lan   green:wan   red:status

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-10-28 18:31:43 +02:00
Rafał Miłecki
b595670070 kernel: backport nvmem v6.6 fixes and v6.7 changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-28 15:20:06 +02:00
John Audia
75aeb7ed62 kernel: bump 5.15 to 5.15.137
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.137

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-27 19:43:06 +01:00
John Audia
5a6368e85d kernel: bump 5.15 to 5.15.136
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.136

Removed bcm53xx patch backported from 5.15.136:
	target/linux/bcm53xx/patches-5.15/081-xhci-Keep-interrupt-disabled-in-initialization-until.patch [1]

All other patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

1. https://github.com/openwrt/openwrt/pull/13751#issuecomment-1781206937

Signed-off-by: John Audia <therealgraysky@proton.me>
[rmilecki: updated commit description & tested on Luxul XWR-3150]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-26 21:40:10 +02:00
Rafał Miłecki
c25c1e28b7 bcm53xx: backport XHCI patch modifying xhci_run_finished()
This will help switching to newer 5.15 kernels. This backport required
rebasing Northstar's USB host patch.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-26 16:06:49 +02:00
Rafał Miłecki
81e7d1776d bcm53xx: add missed spin unlock to USB host patch
Fixes: 265071af7c ("bcm53xx: add testing support for kernel 6.1")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-26 16:06:49 +02:00
John Audia
cd86f6c24d kernel: bump 6.1 to 6.1.60
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.60

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: x86/64/AMD Cezanne, filogic/xiaomi_redmi-router-ax6000-ubootmod

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-26 12:08:52 +02:00
Rafał Miłecki
732ae343ff bcm53xx: backport 1 more late DT patch accepted for v6.7
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-26 08:08:58 +02:00
Linus Walleij
5568f47259
ixp4xx: Add USRobotics USR8200 support
This brings back USRobotics USR8200 support to the IXP4xx
target.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-10-25 11:29:29 +02:00
Linus Walleij
c1318bc73e
ixp4xx: Add a ixp4xx hardware crypto kernel module
The IXP4xx crypto module must be loaded after the rootfs is
up as it depends on loading some NPE microcode from the file
system.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-10-25 11:29:05 +02:00
Linus Walleij
c16b2293fe
ixp4xx: Resurrect IXP4xx support using device tree
This resurrects the support for IXP4xx using device tree
rather than the old (deleted) board files. The final pieces
of IXP4xx board files were deleted in Linux v5.19.

Ext4 root filesystems on CF and USB are supported by the
default config.

We support these three initial targets:

- The Gateworks Avila GW2348 reference design has 64MB of RAM
  and 32MB of flash and also supports USB and CompactFlash.

- The Gateworks Cambria GW2358 reference design has 128MB of
  RAM and 32MB of flash and also supports USB and CompactFlash.

- The old and stable Linksys NSLU2 works fine as well, albeit
  it only has 32MB of RAM so it has been marked as non-default.
  The 8MB of flash can only fit the kernel, so it has been
  patched to boot from exteral media on USB. I have used
  it successfully as a NAS with ksmbd and LUCI web API, see:
  https://dflund.se/~triad/krad/ixp4xx/

Signed-off-by: Howard Harte <hharte@magicandroidapps.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2023-10-25 11:28:38 +02:00
Linus Walleij
33a6189fde
generic: Support Altima AMI101L PHY
This is a backport of the patch to support the Altima AMI101L
PHY which is merged for the v6.7 kernel. This PHY is used in the
IXP4xx-based USRobotics USR8200.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-10-25 11:27:50 +02:00
Linus Walleij
16f929ed47
generic: RTC7301 byte-addressed IO
This is a backport of the patch for byte addressed IO to the
Epson RTC7301 driver. This is used by the IXP4xx-based
USRobotics USR8200.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-10-25 11:27:28 +02:00
Zoltan HERPAI
4898047716 sifiveu: remove 5.15 support
With 6.1 as the default kernel, there is no reason to keep 5.15 around.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-10-24 11:42:46 +02:00
Zoltan HERPAI
fe8630f18e sifiveu: switch to kernel v6.1
Enable kernel v6.1 as the default kernel for sifiveu.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-10-24 11:40:51 +02:00
Rafał Miłecki
a912ee74d6 bcm53xx: disable unused switch ports in downstream patch
This makes Linux use correct switch ports again.

Fixes: a4792d79e8 ("bcm53xx: backport DT changes from v6.5")
Fixes: https://github.com/openwrt/openwrt/issues/13548
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-24 08:26:24 +02:00
Rafał Miłecki
a67af19bc8 bcm53xx: backport DT changes queued for v6.7
Among other changes this commit makes Linux use correct switch ports
again.

Fixes: a4792d79e8 ("bcm53xx: backport DT changes from v6.5")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-24 08:26:24 +02:00
Rafał Miłecki
08ce0c76d7 bcm53xx: simplify patch adding switch ports
We now have all raw ports defined in bcm-ns.dtsi. Leave only lables in
custom device files.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-24 08:26:24 +02:00
Marek Behún
b23c2ec831
kernel: ath79, bmips: refresh 5.15 patches
One LED patch for ath79 and one LED patch for bmips need to be
refreshed.

Signed-off-by: Marek Behún <kabel@kernel.org>
2023-10-23 15:19:49 +02:00
Marek Behún
e257b71eb5
kernel: 5.15: Backport Turris Omnia LED patches
This backports patches
  leds: turris-omnia: convert to use dev_groups
  leds: turris-omnia: Use sysfs_emit() instead of sprintf()
  leds: turris-omnia: Drop unnecessary mutex locking
  leds: turris-omnia: Do not use SMBUS calls
  leds: turris-omnia: Make set_brightness() more efficient
  leds: turris-omnia: Support HW controlled mode via private trigger
  leds: turris-omnia: Add support for enabling/disabling HW gamma correction
  leds: turris-omnia: Fix brightness setting and trigger activating
into backport-5.15.

The above patches replace:
  leds: turris-omnia: support HW controlled mode via private trigger
  leds: turris-omnia: initialize multi-intensity to full
  leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-5.15.

Signed-off-by: Marek Behún <kabel@kernel.org>
2023-10-23 15:19:45 +02:00
Rafał Miłecki
bb629a630f bcm53xx: update patch fixing NVMEM driver for NVRAM
1. Avoid corrupting (replacing '=' with '\0') NVRAM content
2. Check actual NVRAM data length to avoid allocating huge buffers

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-23 11:01:03 +02:00
Hauke Mehrtens
e1aaa1defd Revert "lantiq: xrx200: mark subtarget as source-only"
This reverts commit 0c117e1f6c.

Activate the lantiq/xrx200 target again.

There are still some problems with the GSWIP, but it is not leaking
packets to the wrong bridge in normal operations.
It shows some error messages at configuration like these:
[   54.308861] gswip 1e108000.switch: port 5 failed to add ce:9d:84:d1:81:f0 vid 1 to fdb: -22
[   54.325633] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 0 to fdb: -22
[   54.351242] gswip 1e108000.switch: port 5 failed to add e8🇩🇪27:95:c1:b4 vid 1 to fdb: -22
[   54.358311] gswip 1e108000.switch: port 5 failed to delete ce:9d:84:d1:81:f0 vid 1 from fdb: -2

The problems are described in this pull request:
https://github.com/openwrt/openwrt/pull/13200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-10-23 01:39:47 +02:00
Rani Hod
9c42d23c5f bcm53xx: Linksys EA9200 nvram and 02_network fixes
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.

2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.

Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-10-22 11:11:43 +02:00
Rani Hod
fe5e498777 ramips: TP-link archer A6/C6 device tree updates
Set correct GPIO (10) for the WPS button. This matches GPIO settings in
vendor GPL sources. Note that GPL sources also mention a USB indicator
LED (GPIO 13) but the device has neither an external USB port nor a USB LED.

In addition, prefixes (button-, led-) are added to relevant DT entries,
as well as color and function specifications for LEDs.

Closes: #13736

Reported-by: Waldemar Czabaj <kaball@wp.pl>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(added led mitigations for wifi leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-10-22 11:11:43 +02:00
John Audia
bb8fd41f9a kernel: bump 6.1 to 6.1.59
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.59

Manually rebased:
	bcm27xx/patches-6.1/950-0124-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch

Removed upstreamed:
	generic/backport-6.1/781-v6.6-02-net-dsa-qca8k-fix-potential-MDIO-bus-conflict-when-a.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.59&id=881050b25b1dda7b0f14d40d1b09bf38cb3b427c

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-21 09:33:12 +02:00
John Audia
33e72eba5f kernel: bump 6.1 to 6.1.58
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.58

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-21 09:33:12 +02:00
Marek Mojík
0be05de577
kernel: 6.1: Backport Turris Omnia LED patches
This backports patches
  leds: turris-omnia: Use sysfs_emit() instead of sprintf()
  leds: turris-omnia: Drop unnecessary mutex locking
  leds: turris-omnia: Do not use SMBUS calls
  leds: turris-omnia: Make set_brightness() more efficient
  leds: turris-omnia: Support HW controlled mode via private trigger
  leds: turris-omnia: Add support for enabling/disabling HW gamma correction
  leds: turris-omnia: Fix brightness setting and trigger activating
into backport-6.1.

The above patches replace:
  leds: turris-omnia: support HW controlled mode via private trigger
  leds: turris-omnia: initialize multi-intensity to full
  leds: turris-omnia: change max brightness from 255 to 1
from mvebu/patches-6.1.

Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
2023-10-20 19:17:58 +02:00
Andreas Böhler
fd0aaf93d1 realtek: add support for TP-Link T1600G-28TS v3
This is an RTL8382-based switch with 24 copper ports + 4 SFP ports

Specifications:
---------------
 * SoC:       Realtek RTL8382M
 * Flash:     32 MiB SPI flash
 * RAM:       256 MiB
 * Ethernet:  24x 10/100/1000 Mbps
 * Buttons:   1x "Reset" button
 * UART:      1x serial header, unpopulated
 * SFP:       4 SFP ports

Works:
------
  - (24) RJ-45 ethernet ports
  - Switch functions
  - Buttons
  - Sys LED on front panel (no port LEDs)

Not yet enabled:
----------------
  - Port LEDs (no driver for RTL8231 in this mode)
  - SFP cages (no driver for PHY)

Install via web interface:
-------------------------

Not supported at this time.

Install via serial console/tftp:
--------------------------------

The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.

Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. To install OpenWRT:

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"

Power on device, and stop boot by pressing any key.
Once the shell is active:
 1. Ground out the CLK (pin 16) of the ROM (U6)
 2. Select option "3. Start"
 3. Bootloader notes that "The kernel has been damaged!"
 4. Release CLK as soon as bootloader thinks image is corrupted.
 5. Bootloader enters automatic recovery -- details printed on console
 6. Watch as the bootloader flashes and boots OpenWRT.

Blind install via tftp:
-----------------------

This method works when it's not feasible to install a serial header.

Prepare a tftp server with:
 1. server address: 192.168.0.146
 2. the image as: "uImage.img"
 3. Watch network traffic (tcpdump or wireshark works)
 4. Power on the device.
 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6)
 6. When 192.168.0.30 makes tftp requests, release pin 16
 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2023-10-20 18:13:57 +02:00
Leon M. Busch-George
2657e8cab7 ipq40xx: wpj428: switch to zimage to fit kernel partition
Like with some other ipq40xx devices, the kernel image size for the WPJ428
is limited in stock u-boot. For that reason, the current release doesn't
include an image for the board.
By switching to the zImage format, the kernel image size is reduced which
re-enables the build process. The image boots and behaved normally through
a few days of testing.

Before the switch to kernel version 6.1, it was possible to reduce the
image size by enough when disabling UBIFS and its otherwise unneeded
dependencies.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2023-10-20 18:13:57 +02:00
Christian Lamparter
d6a11833ad apm821xx: WNDR4700: fix broken sysupgrade, factory images
prepend-dtb got extended to handle the Meraki devices too,
the problem here was that the Netgear WNDR4700 expects an
u-boot header in front of the DTB, whereas Meraki devices
don't.

Since the header was dropped, the WNDR4700's uboot started
to complain:
  Bad Magic Number,it is forbidden to be written to flash!!

when flashing the factory.img since it expects an u-boot
header there.

Fixes: 5dece2d9355a ("apm821xx: switch over from DTB_SIZE to DEVICE_DTC_FLAGS")
Reported-by: @kisgezenguz
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-10-20 18:13:57 +02:00
Christian Lamparter
0ba5c0bdc1 ath79: AP105: use fixed layout cell "mac-base"
This drops a use of the deprecated "mac-address-increment".

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2023-10-20 18:13:37 +02:00
Koen Vandeputte
b8e52852bd ipq40xx: switch to performance governor by default
Doing a simple ping to my device shows this:

64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=2.00 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=2.02 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=1.68 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=1.91 ms
64 bytes from 10.0.253.101: icmp_seq=5 ttl=64 time=1.92 ms
64 bytes from 10.0.253.101: icmp_seq=6 ttl=64 time=2.04 ms

Some users even report higher values on older kernels:

64 bytes from 192.168.1.10: seq=0 ttl=64 time=0.612 ms
64 bytes from 192.168.1.10: seq=1 ttl=64 time=2.852 ms
64 bytes from 192.168.1.10: seq=2 ttl=64 time=2.719 ms
64 bytes from 192.168.1.10: seq=3 ttl=64 time=2.741 ms
64 bytes from 192.168.1.10: seq=4 ttl=64 time=2.808 ms

The problem is that the governor is set to Ondemand, which causes
the CPU to clock all the way down to 48MHz in some cases.

Switching to performance governor:

64 bytes from 10.0.253.101: icmp_seq=1 ttl=64 time=0.528 ms
64 bytes from 10.0.253.101: icmp_seq=2 ttl=64 time=0.561 ms
64 bytes from 10.0.253.101: icmp_seq=3 ttl=64 time=0.633 ms
64 bytes from 10.0.253.101: icmp_seq=4 ttl=64 time=0.526 ms

In theory, using the Performance governor should increase power draw,
but it looks like it really does not matter for this soc.

Using a calibrated precision DC power supply (cpu idle):

Ondemand
24.00V * 0.134A = 3.216 Watts
48.00V * 0.096A = 4.608 Watts

Performance
24.00V * 0.135A = 3.240 Watts
48.00V * 0.096A = 4.608 Watts

Let's simply switch to the Performance governor by default
to fix the general jittery behaviour on devices using this soc.

Tested on: MikroTik wAP ac

Fixes: #13649
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
2023-10-20 15:11:41 +02:00
Christian Buschau
67ce60c5f9
armsr: preserve configuration during sysupgrade
Copy configuration to boot partition (partition 1) instead of root
partition (partition 2) because the root partition is not writable if
it's a suqashfs image.
Move configuration back to root during preinit.

Fixes: https://github.com/openwrt/openwrt/issues/13695
Signed-off-by: Christian Buschau <cbuschau@d00t.de>
2023-10-20 00:36:32 +02:00
Pawel Dembicki
65380dc41c layerscape: kernel: refresh 6.1 patches
Kernel patches copied from 5.15 need to be refreshed.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-19 12:39:08 +02:00
Pawel Dembicki
2c9119f72f generic: kernel: add missing symbol
It was found during work on layerscape target.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-19 12:12:02 +02:00
Pawel Dembicki
f54b752764 layerscape: port "-Werror" fix from NXP tree
At this moment, 702-phy-Add-2.5G-SGMII-interface-mode.patch cause error
durring kernel compilation:

  CC      drivers/net/phy/phylink.o
drivers/net/phy/phylink.c: In function 'phylink_get_capabilities':
drivers/net/phy/phylink.c:443:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch]
  443 |         switch (interface) {
      |         ^~~~~~
cc1: all warnings being treated as errors

NXP take care of it. Let's port their patch.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-19 12:12:02 +02:00
Pawel Dembicki
8d95482ca5 layerscape: add 6.1 kernel as testing
It allow to test 6.1 kernel in Layerscape.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-18 08:14:32 +02:00
Pawel Dembicki
d43ac3a643 layerscape: 6.1: refresh kernel config
Done by 'make kernel_oldconfig'.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-18 08:14:32 +02:00
Pawel Dembicki
297fd483bf layerscape: copy config 5.15 to 6.1
Configs was just copied.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-18 08:14:32 +02:00
Pawel Dembicki
d0db036270 layerscape: refresh kernel config
Done by 'make kernel_oldconfig'.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-18 08:14:32 +02:00
Pawel Dembicki
1fb4807d9d layerscape: copy patches 5.15 to 6.1
Patches recreated from NXP 6.1 tree:
400-LF-20-3-mtd-spi-nor-Use-1-bit-mode-of-spansion-s25fs.patch
701-staging-add-fsl_ppfe-driver.patch
702-phy-Add-2.5G-SGMII-interface-mode.patch

Patch 703 includes changes made by Christian Marangi, extracted from commit
0d4a547905.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2023-10-18 08:14:32 +02:00
Shiji Yang
6f31941d38 Revert "ramips: convert MT7915 EEPROM to NVMEM format"
Some MT7915 devices need to load the second part of the eeprom to
work properly. The mt76 driver is not yet ready to read the pre-cal
data via the NVMEM cell. Therefore, partially revert commit to fix
the device probe issue on some devices.

P.S.
Except for D-Link and Ubnt devices, It is still uncertain whether
pre-cal data is required for other devices in the patch.

This partially reverts commit 9ac891f8c4.

Fixes: https://github.com/openwrt/openwrt/issues/13700
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 20:57:07 +08:00
Shiji Yang
9921973ca4
ramips: add missing mt76 packages for Telco Electronics X1
Telco Electronics X1 has MT7603E and MT7612E PCIe NICs. They are
driven by kmod-mt7603 and kmod-mt76x2.

Ref: 73e0f52b6e ("ramips: add support for Telco Electronics X1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:28 +02:00
Shiji Yang
366ffa53bd
ramips: fix factory partition size for SNR-CPE-W4N
The starting address of 'factory' partition is 0x40000, and the
starting address of the next partition is 0x50000. It's obvious
that the correct size for the 'factory' is 0x10000, just like
other MT7620 devices.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:28 +02:00
Shiji Yang
b5d059d677
ramips: fix frequency limit property for some Edimax devices
These three devices uses MT7612E PCIe NIC and supported by the
'mt76' driver. So the right frequency limit property should be
`ieee80211-freq-limit`.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:27 +02:00
Shiji Yang
95e241d2af
ramips: remove useless status property from wmac dts node
On the ramips target, all 'wmac' nodes in SoC dtsi are enabled by
default except mt7628. There is no need to mark them as 'okay'
again. So these useless properties can be removed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:27 +02:00
Shiji Yang
f53fa2a0cb
ramips: convert mt76 PCIe NIC EEPROM to NVMEM format for legacy SoCs
This patch converts MT761{0,2,3} PCIe WiFi calibration data to NVMEM
format for legacy Ralink SoCs (MT7620 and Mt7628). The EEPROM size of
the MT7610 and MT7612 is 0x200. there are only three devices uses
MT7613 NIC, ASUS RT-AC1200 V2, COMFAST CF-WR758AC V2 and Keenetic
KN-1613. The EEPROM size of them is 0x4da8.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:27 +02:00
Shiji Yang
e93f41adee
ramips: convert MT7628 EEPROM to NVMEM format
This patch converts MT7628 WiFi calibration data to NVMEM format. The
EEPROM size is 0x400.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
da42c329c6
ramips: convert rt2x00 EEPROM to NVMEM format
This patch converts legacy Ralink SoCs and MT7620 WiFi calibration
data to NVMEM format. The EEPROM size is 0x200.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
f35ddef268
ramips: fix mtd partition node names for Phicomm PSG1208
The mtd partition node name should be "partition@${offset}".
However, the offsets of the PSG1208 don't match the partition
'reg' properties. This patch correct the wrong offsets.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
7668fc8112
ramips: fix DTS EEPROM property for some MT7628 devices
The MT7628 integrated wireless is driven by `mt76`, so the right
EEPROM property name is `mediatek,mtd-eeprom`.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:26 +02:00
Shiji Yang
58502650e1
ramips: convert the remaining mtd-mac-address to NVMEM format
`mtd-mac-address` has been abandoned. Therefore, convert them to
NVMEM format. This patch also removes some useless mtd-mac-address
properties.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-10-17 12:07:22 +02:00
Robert Marko
1c7fd93fc2 qualcommax: ipq8074: use upstreamed CPUFreq NVMEM support
IPQ8074 CPUFreq NVMEM support has finally landed upstream, so lets use the
upstreamed version.

This has a benefit of also supporting IPQ8174 (Oak) family for which SMEM
SoC ID-s were also upstreamed.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-10-16 19:22:11 +02:00
Christian Marangi
e0ac782a5e
lantiq: update binding for ralink EEPROM swap
Binding for ralink EEPROM swap changed from ralink,mtd-eeprom-swap to
ralink,eeprom-swap.

Update every entry.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-10-16 14:16:58 +02:00
Bjørn Mork
2e57028424
ramips: fix ZyXEL NR7101 bricking typo
A typo snuck in with the addition of Cudy M1800, changing
"nr7101" to "nt7101". The result is a default network config
for NR7101 without the only ethernet interface on the NR7101,
thereby soft bricking it.

Fixes: f6d394e9f2 ("ramips: add support for Cudy M1800")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-10-15 19:28:59 +02:00
Robert Marko
f8ea89c2d4 qualcommax: add pending GPLL parent fixes
SBL will configure IPQ807x cores to boot at 800MHz as a safe default
frequency that is provided by GPLL0, but GPLL0 is not currently configured
as a possible parent in the APSS clock driver not being passed to it via
DTS which will then cause the kernel to not properly identify the current
CPU frequency during booting and will think that CPU is currently at XO
frequency of 19.2MHz instead of 800MHz cores are actually at and print:
cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 19200 KHz, changing to: 1017600 KHz

So, lets import patches pending upstream to prevent GPLL scaling and feed
the GPLL0 clock to APSS clock driver so we get:
cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz

This is mostly cosmetic fix, but with all of the possible SBL and FW
versions there could be edge cases resolved by this and not scaling GPLL-s
anymore.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-10-15 17:29:39 +02:00
John Audia
b357564463 kernel: bump 6.1 to 6.1.57
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.57

Manually rebased:
	generic/pending-6.1/702-net-ethernet-mtk_eth_soc-enable-threaded-NAPI.patch

Removed upstreamed:
	qualcommax/patches-6.1/0134-PCI-qcom-Fixing-broken-pcie-enumeration-for-2_3_3-co.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.57&id=2dfb5f324d799f4545e17631415aba6d302a8e2b

Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-14 15:51:53 +02:00
John Audia
ccf24b5dcd config-6.1: disable CONFIG_ARM64_ERRATUM_2966298
Disable new ksym globally as OpenWrt does not have any targets that
use A520 cores.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-14 15:51:44 +02:00
Koen Vandeputte
9188c77cbe ath79: wpj563: enable 2nd USB controller
The compex WPJ563 actually has both usb controllers wired:

usb0 --> pci-e slot
usb1 --> pin header

As the board exposes it for generic use, enable this controller too.

fixes: #13650
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
2023-10-13 17:47:48 +02:00
Rani Hod
802a5f5cb4 bcm53xx: build a single device per profile
So far every build of a single bcm53xx Target Profile (it means: when
NOT using CONFIG_TARGET_MULTI_PROFILE) resulted in all target devices
images being built. Now it only builds the one matching selected
profile.

Fixes: #13572

Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
[rmilecki: update commit subject + body & move PROFILES line]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-10-13 07:32:22 +02:00
John Audia
096bb8ed82 kernel: bump 5.15 to 5.15.135
Changelog: https://cdn.kernel.org/pub/linux/kernel/v5.x/ChangeLog-5.15.135

All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-10-12 08:26:06 +02:00
Hauke Mehrtens
66f6c20e45 lantiq: Fix an sleeping function called from invalid context
The ifx_pcie_bus_enum_hack() function is called in
ifx_pcie_read_config() while holding the ifx_pcie_lock spinlock. The
ifx_pcie_bus_enum_hack() function calls pci_get_slot() which could
sleep. Add a new function for pci_get_slot() which does not use a
semaphore, the mutex should be sufficient. This fixes the sleep in
atomic context which could cause a hang of the system.

This fixes the following warning seen with
CONFIG_KERNEL_DEBUG_ATOMIC_SLEEP=y.

[   12.264300] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   12.272226] BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:1487
[   12.280684] in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 9, name: kworker/u4:0
[   12.288781] CPU: 0 PID: 9 Comm: kworker/u4:0 Not tainted 5.15.134 #0
[   12.295135] Workqueue: events_unbound deferred_probe_work_func
[   12.300964] Stack : 80e70000 8008ac80 00000000 00000004 807c776c 8145b9ec 81424c00 800520ec
[   12.309316]         808a0000 8145ba2b 8145b844 8145b838 80414178 00000001 8145b9f8 81439ea0
[   12.317674]         00000000 00000000 807c776c 8145b838 ffffefff 00000000 00000000 ffffffea
[   12.326030]         00000081 8145b844 00000081 808a6f50 807c776c 00000000 00000000 80910000
[   12.334391]         00111bef 00000000 00000001 00000000 00000018 00000030 00000000 80e40000
[   12.342741]         ...
[   12.345177] Call Trace:
[   12.347613] [<8000c1d0>] show_stack+0x28/0xf0
[   12.351974] [<8038ba1c>] dump_stack_lvl+0x60/0x80
[   12.356667] [<8005eefc>] ___might_sleep+0x124/0x138
[   12.361547] [<806daf30>] down_read+0x24/0x88
[   12.365807] [<803cdd20>] pci_get_slot+0x2c/0xc0
[   12.370333] [<806d56ac>] ifx_pcie_read_config+0x164/0x330
[   12.375735] [<803be610>] pci_bus_read_config_dword+0x6c/0xd0
[   12.381399] [<803c20cc>] pci_bus_generic_read_dev_vendor_id+0x3c/0x1a8
[   12.387915] [<803c27ec>] pci_scan_single_device+0x88/0x154
[   12.393404] [<803c2928>] pci_scan_slot+0x70/0x134
[   12.398099] [<803c3bf0>] pci_scan_child_bus_extend+0x5c/0x320
[   12.403849] [<803c4178>] pci_scan_root_bus_bridge+0xd0/0xec
[   12.409414] [<806d45a8>] pcibios_scanbus+0xe4/0x21c
[   12.414293] [<806d4908>] register_pci_controller+0xb8/0x11c
[   12.419858] [<806d5f9c>] ifx_pcie_bios_probe+0x724/0x940
[   12.425174] [<80417574>] platform_probe+0x38/0x90
[   12.429868] [<80414d68>] really_probe.part.0+0xac/0x354
[   12.435103] [<80415298>] driver_probe_device+0x4c/0x154
[   12.440313] [<80415904>] __device_attach_driver+0xd0/0x15c
[   12.445802] [<804129d8>] bus_for_each_drv+0x70/0xb0
[   12.450676] [<80415610>] __device_attach+0xdc/0x194
[   12.455545] [<80413ca8>] bus_probe_device+0x9c/0xb8
[   12.460419] [<8041420c>] deferred_probe_work_func+0x94/0xd4
[   12.465995] [<8004fcb4>] process_one_work+0x27c/0x4c8
[   12.471044] [<80050710>] worker_thread+0x34c/0x5f8
[   12.475825] [<800587a8>] kthread+0x168/0x18c
[   12.480090] [<80006ef8>] ret_from_kernel_thread+0x14/0x1c

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-10-10 00:22:25 +02:00