ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-02-18 16:40:29 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity

mvebu: add support for Fortinet FortiGate 30E

Browse Source 
Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 5x 10/100/1000 Mbps
  - Switch     : Marvell 88E6176
- LEDs/Keys    : 16x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Modex 5557-02R

Flash instruction using initramfs image:

 1. Power on FG-30E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "r" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex))
WAN   : 70:4C:A5:xx:xx:CF
LAN 1 : 70:4C:A5:xx:xx:D0
LAN 2 : 70:4C:A5:xx:xx:D1
LAN 3 : 70:4C:A5:xx:xx:D2
LAN 4 : 70:4C:A5:xx:xx:D3

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit is contained in:
INAGAKI Hiroshi 2023-03-21 15:23:56 +09:00 committed by Hauke Mehrtens
parent 4b0b90d3fa
commit b7c12a9bfc
6 changed files with 490 additions and 360 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

13
target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
View File

@ -18,12 +18,7 @@ mvebu_setup_interfaces()
cznic,turris-omnia)
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" "eth2"
;;
fortinet,fg-50e)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "eth1 eth2"
;;
iptime,nas1dual)
ucidef_set_interface_lan "eth0 eth1" "dhcp"
;;
fortinet,fg-30e|\
linksys,wrt1200ac|\
linksys,wrt1900ac-v1|\
linksys,wrt1900ac-v2|\
@ -32,6 +27,12 @@ mvebu_setup_interfaces()
linksys,wrt32x)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
fortinet,fg-50e)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "eth1 eth2"
;;
iptime,nas1dual)
ucidef_set_interface_lan "eth0 eth1" "dhcp"
;;
marvell,a385-db-ap)
ucidef_set_interfaces_lan_wan "eth0 eth1" "eth2"
;;

1
target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
View File

@ -52,6 +52,7 @@ platform_do_upgrade() {
solidrun,clearfog-pro-a1)
legacy_sdcard_do_upgrade "$1"
;;
fortinet,fg-30e|\
fortinet,fg-50e)
fortinet_do_upgrade "$1"
;;

104
target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-30e.dts Normal file
View File

@ -0,0 +1,104 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
#include "armada-385-fortinet-fg-x0e.dtsi"
/ {
model = "Fortinet FortiGate 30E";
compatible = "fortinet,fg-30e", "marvell,armada385", "marvell,armada380";
memory@0 {
device_type = "memory";
reg = <0x00000000 0x40000000>; /* 1GB */
};
};
&gpio_leds {
led-14 {
label = "amber:speed_wan";
gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:00:100Mbps";
};
led-15 {
label = "green:speed_wan";
gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:00:1Gbps";
};
};
&pinctrl {
pmx_switch_pins: switch-pins {
marvell,pins = "mpp19";
marvell,function = "gpio";
};
};
&mdio {
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins>, <&pmx_switch_pins>;
/* Marvell 88E6176 */
switch@2 {
compatible = "marvell,mv88e6085";
reg = <0x2>;
reset-gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "wan";
nvmem-cells = <&macaddr_bdinfo_d880>;
nvmem-cell-names = "mac-address";
mac-address-increment = <1>;
};
port@1 {
reg = <1>;
label = "lan4";
nvmem-cells = <&macaddr_bdinfo_d880>;
nvmem-cell-names = "mac-address";
mac-address-increment = <5>;
};
port@2 {
reg = <2>;
label = "lan3";
nvmem-cells = <&macaddr_bdinfo_d880>;
nvmem-cell-names = "mac-address";
mac-address-increment = <4>;
};
port@3 {
reg = <3>;
label = "lan2";
nvmem-cells = <&macaddr_bdinfo_d880>;
nvmem-cell-names = "mac-address";
mac-address-increment = <3>;
};
port@4 {
reg = <4>;
label = "lan1";
nvmem-cells = <&macaddr_bdinfo_d880>;
nvmem-cell-names = "mac-address";
mac-address-increment = <2>;
};
port@6 {
reg = <6>;
ethernet = <&eth0>;
phy-connection-type = "rgmii-id";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};

379
target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts
View File

@ -1,215 +1,45 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include "armada-385.dtsi"
#include "armada-385-fortinet-fg-x0e.dtsi"
/ {
model = "Fortinet FortiGate 50E";
compatible = "fortinet,fg-50e", "marvell,armada385", "marvell,armada380";
aliases {
led-boot = &led_status_green;
led-failsafe = &led_status_red;
led-running = &led_status_green;
led-upgrade = &led_status_green;
label-mac-device = &eth0;
};
chosen {
stdout-path = "serial0:9600n8";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x80000000>; /* 2GB */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pmx_gpio_keys_pins>;
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
};
};
gpio-leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pmx_gpio_leds_pins>;
led-0 {
label = "red:alarm";
gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_ALARM;
};
led-1 {
label = "red:ha";
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_RED>;
};
led_status_green: led-2 {
label = "green:sta";
gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_STATUS;
};
led-3 {
label = "green:ha";
gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
};
led-4 {
label = "amber:alarm";
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_ALARM;
};
led_status_red: led-5 {
label = "red:sta";
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_STATUS;
};
led-6 {
label = "green:speed_wan1";
gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "f1072004.mdio-mii:00:1Gbps";
};
led-7 {
label = "green:speed_wan2";
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "f1072004.mdio-mii:01:1Gbps";
};
led-8 {
label = "amber:speed_lan5";
gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:00:100Mbps";
};
led-9 {
label = "green:speed_lan5";
gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:00:1Gbps";
};
led-10 {
label = "green:speed_lan4";
gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:01:1Gbps";
};
led-11 {
label = "amber:speed_lan4";
gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:01:100Mbps";
};
led-12 {
label = "amber:speed_lan3";
gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:02:100Mbps";
};
led-13 {
label = "green:speed_lan3";
gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:02:1Gbps";
};
led-14 {
label = "green:speed_lan1";
gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:04:1Gbps";
};
led-15 {
label = "amber:speed_lan1";
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:04:100Mbps";
};
led-16 {
label = "green:speed_lan2";
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:03:1Gbps";
};
led-17 {
label = "amber:speed_lan2";
gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:03:100Mbps";
};
};
reg_usb_vbus: regulator-usb-vbus {
compatible = "fixed-regulator";
regulator-name = "usb-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
regulator-always-on;
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "okay";
gpio2: gpio@24 {
compatible = "nxp,pca9555";
reg = <0x24>;
gpio-controller;
#gpio-cells = <0x2>;
&gpio_leds {
led-14 {
label = "green:speed_wan1";
gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "f1072004.mdio-mii:00:1Gbps";
};
hwmon@28 {
compatible = "nuvoton,nct7802";
reg = <0x28>;
led-15 {
label = "green:speed_wan2";
gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "f1072004.mdio-mii:01:1Gbps";
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
led-16 {
label = "amber:speed_lan5";
gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:00:100Mbps";
};
led-17 {
label = "green:speed_lan5";
gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:00:1Gbps";
};
};
&pinctrl {
@ -217,48 +47,6 @@
marvell,pins = "mpp19", "mpp20", "mpp23", "mpp34", "mpp41";
marvell,function = "gpio";
};
pmx_gpio_leds_pins: gpio-leds-pins {
marvell,pins = "mpp30", "mpp32", "mpp33", "mpp35",
"mpp45", "mpp47";
marvell,function = "gpio";
};
pmx_usb_pins: usb-pins {
marvell,pins = "mpp53";
marvell,function = "gpio";
};
pmx_gpio_keys_pins: gpio-keys-pins {
marvell,pins = "mpp54";
marvell,function = "gpio";
};
};
&bm {
status = "okay";
};
&bm_bppi {
status = "okay";
};
&eth0 {
pinctrl-names = "default";
pinctrl-0 = <&ge0_rgmii_pins>;
status = "okay";
phy-connection-type = "rgmii-id";
buffer-manager = <&bm>;
bm,pool-long = <0>;
bm,pool-short = <1>;
nvmem-cells = <&macaddr_bdinfo_d880>;
nvmem-cell-names = "mac-address";
fixed-link {
speed = <1000>;
full-duplex;
};
};
&eth1 {
@ -388,120 +176,3 @@
};
};
};
&usb3_0 {
pinctrl-names = "default";
pinctrl-0 = <&pmx_usb_pins>;
status = "okay";
vbus-supply = <&reg_usb_vbus>;
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x1c0000>;
label = "u-boot";
read-only;
};
partition@1c0000 {
reg = <0x1c0000 0x10000>;
label = "firmware-info";
/*
* 0x10 - 0x2f : image name (image1)
* 0x30 - 0x4f : image name (image2)
* 0x170 (1byte): active image (0x0/0x1)
* 0x184 - 0x185: kernel block count (image1)
* 0x18c - 0x18d: rootfs block count (image1)
* 0x194 - 0x195: kernel block count (image2)
* 0x19c - 0x19d: rootfs block count (image2)
* 0x1be (1byte): bit7 -> active flag (image1)?
* 0x1ce (1byte): bit7 -> active flag (image2)?
*
* Note: block size --> 0x200 (512 bytes)
*/
};
partition@1d0000 {
reg = <0x1d0000 0x10000>;
label = "dtb";
read-only;
};
partition@1e0000 {
reg = <0x1e0000 0x10000>;
label = "u-boot-env";
read-only;
};
partition@1f0000 {
reg = <0x1f0000 0x10000>;
label = "board-info";
read-only;
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_bdinfo_d880: macaddr@d880 {
reg = <0xd880 0x6>;
};
};
partition@200000 {
reg = <0x200000 0x600000>;
label = "kernel";
};
partition@800000 {
reg = <0x800000 0x1800000>;
label = "rootfs";
};
partition@2000000 {
reg = <0x2000000 0x600000>;
label = "kn2";
read-only;
};
partition@2600000 {
reg = <0x2600000 0x1800000>;
label = "rfs2";
read-only;
};
partition@3e00000 {
reg = <0x3e00000 0x1200000>;
label = "part1";
read-only;
};
partition@5000000 {
reg = <0x5000000 0x1200000>;
label = "part2";
read-only;
};
partition@6200000 {
reg = <0x6200000 0x1e00000>;
label = "config";
read-only;
};
};
};
};

338
target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-x0e.dtsi Normal file
View File

@ -0,0 +1,338 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include "armada-385.dtsi"
/ {
aliases {
led-boot = &led_status_green;
led-failsafe = &led_status_red;
led-running = &led_status_green;
led-upgrade = &led_status_green;
label-mac-device = &eth0;
};
chosen {
stdout-path = "serial0:9600n8";
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&pmx_gpio_keys_pins>;
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
};
};
gpio_leds: gpio-leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&pmx_gpio_leds_pins>;
led-0 {
label = "red:alarm";
gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_ALARM;
};
led-1 {
label = "red:ha";
gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_RED>;
};
led_status_green: led-2 {
label = "green:sta";
gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_STATUS;
};
led-3 {
label = "green:ha";
gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
};
led-4 {
label = "amber:alarm";
gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_ALARM;
};
led_status_red: led-5 {
label = "red:sta";
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_STATUS;
};
led-6 {
label = "green:speed_lan4";
gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:01:1Gbps";
};
led-7 {
label = "amber:speed_lan4";
gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:01:100Mbps";
};
led-8 {
label = "amber:speed_lan3";
gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:02:100Mbps";
};
led-9 {
label = "green:speed_lan3";
gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:02:1Gbps";
};
led-10 {
label = "green:speed_lan1";
gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:04:1Gbps";
};
led-11 {
label = "amber:speed_lan1";
gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:04:100Mbps";
};
led-12 {
label = "green:speed_lan2";
gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_GREEN>;
linux,default-trigger = "mv88e6xxx-1:03:1Gbps";
};
led-13 {
label = "amber:speed_lan2";
gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
color = <LED_COLOR_ID_AMBER>;
linux,default-trigger = "mv88e6xxx-1:03:100Mbps";
};
};
reg_usb_vbus: regulator-usb-vbus {
compatible = "fixed-regulator";
regulator-name = "usb-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
regulator-always-on;
};
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "okay";
gpio2: gpio@24 {
compatible = "nxp,pca9555";
reg = <0x24>;
gpio-controller;
#gpio-cells = <0x2>;
};
hwmon@28 {
compatible = "nuvoton,nct7802";
reg = <0x28>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
&pinctrl {
pmx_gpio_leds_pins: gpio-leds-pins {
marvell,pins = "mpp30", "mpp32", "mpp33", "mpp35",
"mpp45", "mpp47";
marvell,function = "gpio";
};
pmx_usb_pins: usb-pins {
marvell,pins = "mpp53";
marvell,function = "gpio";
};
pmx_gpio_keys_pins: gpio-keys-pins {
marvell,pins = "mpp54";
marvell,function = "gpio";
};
};
&bm {
status = "okay";
};
&bm_bppi {
status = "okay";
};
&eth0 {
pinctrl-names = "default";
pinctrl-0 = <&ge0_rgmii_pins>;
status = "okay";
phy-connection-type = "rgmii-id";
buffer-manager = <&bm>;
bm,pool-long = <0>;
bm,pool-short = <1>;
nvmem-cells = <&macaddr_bdinfo_d880>;
nvmem-cell-names = "mac-address";
fixed-link {
speed = <1000>;
full-duplex;
};
};
&usb3_0 {
pinctrl-names = "default";
pinctrl-0 = <&pmx_usb_pins>;
status = "okay";
vbus-supply = <&reg_usb_vbus>;
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins>;
status = "okay";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <50000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
reg = <0x0 0x1c0000>;
label = "u-boot";
read-only;
};
partition@1c0000 {
reg = <0x1c0000 0x10000>;
label = "firmware-info";
/*
* 0x10 - 0x2f : image name (image1)
* 0x30 - 0x4f : image name (image2)
* 0x170 (1byte): active image (0x0/0x1)
* 0x184 - 0x185: kernel block count (image1)
* 0x18c - 0x18d: rootfs block count (image1)
* 0x194 - 0x195: kernel block count (image2)
* 0x19c - 0x19d: rootfs block count (image2)
* 0x1be (1byte): bit7 -> active flag (image1)?
* 0x1ce (1byte): bit7 -> active flag (image2)?
*
* Note: block size --> 0x200 (512 bytes)
*/
};
partition@1d0000 {
reg = <0x1d0000 0x10000>;
label = "dtb";
read-only;
};
partition@1e0000 {
reg = <0x1e0000 0x10000>;
label = "u-boot-env";
read-only;
};
partition@1f0000 {
reg = <0x1f0000 0x10000>;
label = "board-info";
read-only;
compatible = "nvmem-cells";
#address-cells = <1>;
#size-cells = <1>;
macaddr_bdinfo_d880: macaddr@d880 {
reg = <0xd880 0x6>;
};
};
partition@200000 {
reg = <0x200000 0x600000>;
label = "kernel";
};
partition@800000 {
reg = <0x800000 0x1800000>;
label = "rootfs";
};
partition@2000000 {
reg = <0x2000000 0x600000>;
label = "kn2";
read-only;
};
partition@2600000 {
reg = <0x2600000 0x1800000>;
label = "rfs2";
read-only;
};
partition@3e00000 {
reg = <0x3e00000 0x1200000>;
label = "part1";
read-only;
};
partition@5000000 {
reg = <0x5000000 0x1200000>;
label = "part2";
read-only;
};
partition@6200000 {
reg = <0x6200000 0x1e00000>;
label = "config";
read-only;
};
};
};
};

15
target/linux/mvebu/image/cortexa9.mk
View File

@ -95,6 +95,21 @@ define Device/cznic_turris-omnia
endef
TARGET_DEVICES += cznic_turris-omnia
define Device/fortinet_fg-30e
DEVICE_VENDOR := Fortinet
DEVICE_MODEL := FortiGate 30E
SOC := armada-385
KERNEL := kernel-bin | append-dtb
KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
gzip-filename FGT30E
KERNEL_SIZE := 6144k
DEVICE_DTS := armada-385-fortinet-fg-30e
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
sysupgrade-tar rootfs=$$$$@ | append-metadata
DEVICE_PACKAGES := kmod-hwmon-nct7802
endef
TARGET_DEVICES += fortinet_fg-30e
define Device/fortinet_fg-50e
DEVICE_VENDOR := Fortinet
DEVICE_MODEL := FortiGate 50E