Commit Graph

19327 Commits

Author SHA1 Message Date
Thibaut VARÈNE
3442ec5d57 ar71xx: define switch for rb-952ui-5ac2nd
QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 0e43c31ebde996ca88f5857bb7e6c4cbf3f65756)
2018-07-30 18:14:17 +02:00
张鹏
a3dd6c939d ar71xx:add support for E750G v8
Qxwlan E750G v8 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (PoE support)
 - 2x 10/100/1000 Mbps Ethernet
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit 53a4502013)
2018-07-30 14:02:41 +02:00
张鹏
11a5128b98 ar71xx:add support for E750A v4
Qxwlan E750A v4 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 5G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (one port with PoE support)
 - 1x miniPCIe slot (USB 2.0 bus only)
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit ac03d51a3f)
2018-07-30 14:02:40 +02:00
张鹏
21ad5fb1ea ar71xx:add support for E558 v2
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.

Specification:

 - 720/600/200 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz (QCA9558)
 - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 4x miniPCIe slot (USB 2.0 bus only)
 - 1x microSIM slot
 - 5x LED (4 driven by GPIO)
 - 1x button (reset)
 - 1x 3-pos switch
 - 1x DC jack for main power input (9-48 V)
 - UART (JP5) and LEDs (J8) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit b74f63f81d)
2018-07-30 14:02:40 +02:00
Christian Lamparter
4dc0ff8183 brcm2708: split sdcard.img.gz into a sysupgrade and factory image
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>

@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.

Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7516a96011)
2018-07-30 14:00:59 +02:00
Thibaut VARÈNE
cb73dd21a3 ar71xx: rbspi: fix RB wAP AC gpio conflict and LED
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.

Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.

This patch fixes these issues and renames the corresponding #defines for
clarity

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit e99f760235)
2018-07-30 11:12:41 +02:00
Thibaut VARÈNE
bb06f6d3ba ar71xx: add missing diag LED support for RB wAP 2nD
3b15eb06c3 did not include diag.sh
edit

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 5c2419b6f8)
2018-07-30 11:12:41 +02:00
Jo-Philipp Wich
c8e8ff1c9f brcm47xx: rework model detection
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.

Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.

As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.

Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.

Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

(cherry picked from commit d7d10f2c1e)
2018-07-30 11:11:21 +02:00
Rafał Miłecki
ca0c649a38 bcm53xx: revert SPI controller commit breaking flash reads
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0417b08b06)
2018-07-29 11:10:03 +02:00
Rafał Miłecki
962e86d9af brcm47xx: revert upstream commit breaking BCM4718A1
This fixes kernel hang when booting on BCM4718A1 (& probably BCM4717A1).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4c1aa64b4d)
2018-07-27 16:00:31 +02:00
Tim Small
90b15b00a2 WDR4900v1 remove dt node for absent hw crypto.
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC.  However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines.  If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.

This commit overrides the incorrect dt node definition in the included
file.

See also:
 - https://bugs.openwrt.org/index.php?do=details&task_id=1262
 - https://community.nxp.com/thread/338432#comment-474107

Signed-off-by: Tim Small <tim@seoss.co.uk>
(cherry picked from commit e97aaf483c)
2018-07-21 18:38:18 +02:00
Christian Lamparter
8a0ad2660a apm821xx: fix sata access freezes
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" fixes the
freezes according to @takimata, @And.short, that have been
reported on the forum by @ticerex.

Furtheremore, @takimata reported that the patch also improved
the performance of the HDDs considerably:
|<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/55>
|It seems your patch unleashed the full power of the SATA port.
|Where I was previously hitting a really hard limit at around
|82 MB/s for reading and 27 MB/s for writing, I am now getting this:
|
|root@OpenWrt:/mnt# time dd if=/dev/zero of=tempfile bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real    0m 13.65s
|user    0m 0.01s
|sys     0m 11.89s
|
|root@OpenWrt:/mnt# time dd if=tempfile of=/dev/null bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real    0m 8.41s
|user    0m 0.01s
|sys     0m 4.70s
|
|This means: 121 MB/s reading and 75 MB/s writing!
|
|[...]
|
|The drive is a WD Green WD10EARX taken from an older MBL Single.
|I repeated the test a few times with even larger files to rule out
|any caching, I'm still seeing the same great performance. OpenWrt is
|now completely on par with the original MBL firmware's performance.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-07-19 18:54:40 +02:00
Jo-Philipp Wich
f8cc68670f mediatek: fix parallel build issues in image build code
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.

Also remove unused .dtb references in the mt7623 subtarget.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 8194f9ef4a)
2018-07-17 14:45:33 +02:00
Christian Lamparter
aee917a5a2 apm821xx: fix usb-otg on 4.14
Starting with 4.14, the "amcc,dwc-otg" needs to be used
in order to get the usb-otg to work.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 12b80f1cab)
2018-07-16 08:43:15 +02:00
David Bauer
dc52b7b104
ipq40xx: add get_status_led to diag.sh
This commit adds the get_status_led method to diag.sh, which sets the
boot-led as status-led for scripts using this method to get a
status-led.

This method is used platform-independent in downstream project gluon to
set the LED used to indicate the config-mode.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4fc005197a)
2018-07-15 20:08:44 +02:00
Felix Fietkau
c99c70e053 kernel: backport page fragment API changes from 4.10+ to 4.9
mt76 now relies on this API

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-14 11:43:18 +02:00
Kevin Darbyshire-Bryant
3e81365141 kernel: gen_stats: Fix netlink stats dumping in the presence of padding
Backport hot off the press upstream netlink patch.  Fixes stats display
from CAKE qdisc on MIPS allowing us to bump CAKE to latest version.

The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.

However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.

Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 3698b34a00)
2018-07-13 16:08:34 +01:00
Felix Fietkau
dd1f97b37d ramips: clean up and fix MT7621 NAND driver issues
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align

Let the MTD core take care of both

Fixes messages like these:
[  102.820541] Data buffer not 16 bytes aligned: 87daf08c

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-13 17:01:41 +02:00
Felix Fietkau
16a9ddfe64 ramips: ethernet: use own page_frag_cache
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.

Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-13 16:39:49 +02:00
Felix Fietkau
0e6cfb6919 ramips: ethernet: use skb_free_frag to free fragments
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-13 16:39:46 +02:00
Peter Lundkvist
2f306873ef ramips: TP-Link TL-WR902AC v3: add missing wps button
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
2018-07-12 18:27:36 +02:00
Peter Lundkvist
36a4681b2b ramips: TP-Link TL-WR902AC v3: don't build factory image
The line that produces factory image was accidentally left by me while
testing before inital commit.

I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).

I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.

So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.

Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:27:36 +02:00
Koen Vandeputte
ca903c73c7 kernel: bump 4.14 to 4.14.54 for 18.06
Refreshed all patches

Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-12 13:54:24 +02:00
Koen Vandeputte
3a5498c5e5 kernel: bump 4.9 to 4.9.111 for 18.06
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-07-12 13:54:24 +02:00
Rafał Miłecki
5a40fad22a kernel: bcm47xxpart: fix getting user-space data partition name
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.

This fixes UBI support for devices that have kernel flashed on partition
with a bad block.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7ddba08d87)
2018-07-10 14:11:15 +02:00
Aleksandr V. Piskunov
5745bbe7d5 ipq806x: fix numbering for Netgear R7800 LAN ports
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-07-04 01:20:44 +02:00
Mathias Kresin
603870e871 lantiq: backport stp-xway get callback implementation
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.

Fixes: FS#1620

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-03 20:59:27 +02:00
Felix Fietkau
5505ab5c94 ramips: limit dictionary size for lzma compression
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.

Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-07-03 11:20:37 +02:00
Stijn Segers
ab7cabd09d kernel: bump 4.14 to 4.14.52 for 18.06
Compile-tested on: ramips/mt7621, x86/64.
Run-tested on: ramips/mt7621.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2018-07-02 07:06:23 +02:00
Stijn Segers
c96b344466 kernel: bump 4.9 to 4.9.110 for 18.06
Compile-tested on ar71xx.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2018-07-02 07:06:06 +02:00
Andrey Jr. Melnikov
1961cdfb57 ramips: move mt7620n i2c_pins definition to right place
Move to i2c pins pinmux node to the pinctrl node.

Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")

Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-27 23:48:32 +02:00
Hannu Nyman
dba362772e ipq806x: remove "firmware" partition definition from netgear routers
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.

Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
  [    1.111324] 0x000001480000-0x000001880000 : "kernel"
  [    1.121005] 0x000001880000-0x000007900000 : "ubi"
  [    1.283912] 0x000007900000-0x000008000000 : "reserve"
  [    1.296407] 0x000001480000-0x000007900000 : "firmware"
  [    1.468043] no rootfs found after FIT image in "firmware"
  [    2.426860] 2 uimage-fw partitions found on MTD device firmware
  [    2.426931] 0x000001480000-0x000001880000 : "kernel"
  [    2.440420] 0x000001880000-0x000007900000 : "ubi"

Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
  Writing from <stdin> to kernel ...
  ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
  ubiattach: error!: bad MTD device number: "6 mtd10"

The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.

Only tested for the R7800 but all of them should behave equal.

Fixes: FS#1617

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-27 22:10:23 +02:00
Hannu Nyman
618d59aec2 ipq806x: Enlarge R7800 flash - use netgear partition
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.

Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.

In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.

Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit

Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52

Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-06-27 22:10:23 +02:00
INAGAKI Hiroshi
7775802eb9 ramips: add switch port index for I-O DATA WN-GX300GR
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0

1-4: lan
0: wan

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-27 08:41:13 +02:00
Adrian Schmutzler
286a456319
ar71xx: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 5c5bf8b865)
2018-06-23 16:08:22 +02:00
Adrian Schmutzler
5dd3400746
ar71xx: Add TP-Link Pharos v2 board detection
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.

Code was written mostly by Alexander Couzens <lynxis@fe80.eu>

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2524febf79)
2018-06-23 16:08:20 +02:00
Rafał Miłecki
6eaffbd6ee bcm53xx: fix NAND partitions on D-Link DIR-885L
This fixes missing rootfs on above device:
[    2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[    2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e53d0da775)
2018-06-23 14:27:29 +02:00
Chen Minqiang
71825c0bd8 kernel: cleanup offload hooks on netdev unregister
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit e317bb06fd)
2018-06-22 11:23:35 +02:00
Hans Dedecker
7f3121cf8a kernel: backport fix for missing tunnel encapsulation limit option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-06-21 22:10:06 +02:00
Mathias Kresin
c276abf061 lantiq: fix arcadyan vg3503j switch port indexing
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-21 22:01:33 +02:00
Chuanhong Guo
7950e1b9f4 ramips: Add support for Phicomm K2G
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-06-21 22:01:33 +02:00
Arvid E. Picciani
4e9fa569b0 ar71xx: add support for TP-LINK Archer C7 v5
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Arvid E. Picciani <aep@exys.org>
(cherry picked from commit bf39d5594b)
2018-06-21 07:02:51 +02:00
David Bauer
29934e5f03 ar71xx: add support for Fritz!WLAN Repeater 450E
This commit adds support for the AVM Fritz!WLAN Repeater 450E

SOC:    Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM:    64MB Zentel A3R12E40CBF DDR2
FLASH:  16MiB Winbond W25Q128 SPI NOR
WLAN1:  QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT:  WPS button
LED:    Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
        Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4GHz WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - Most LEDs

Not working:
 - 2 RSSI LEDs
   AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
   control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
   While it is possible to implement this feature, it would require an
   additional kernel patch for a minor functionality.

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b4bf43c667)
2018-06-21 07:02:43 +02:00
Magnus Frühling
36234df96c ipq40xx: add support for ZyXEL WRE6606
Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	128 MB Nanya NT5CC64M16GP-DI
FLASH:	16 MiB Macronix MX25L12845EMI-12G
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:  WPS, Mode-toggle-switch
LED:	Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
        (LAN not controllable by software)
        (WLAN each green / red)
SERIAL:	Header next to eth-phy.
        VCC, TX, GND, RX (Square hole is VCC)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (Correct MAC-address)
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from tftp
 - OpenWRT sysupgrade
 - LEDs
 - WPS Button

Not Working:
 - Mode-toggle-switch

Install via TFTP:

Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.

To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.

append-cmdline patch taken from chunkeeys work on the NBG6617.

Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
(cherry picked from commit 4b280ad91a)
2018-06-21 07:02:37 +02:00
David Bauer
0c4f658d58 ar71xx: add support for OCEDO Koala
This commit adds support for the OCEDO Koala

SOC:	Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit e36f8b3f39)
2018-06-21 07:02:30 +02:00
David Bauer
9178dc282d ar71xx: fix incorrect speed setting on QCA9556
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.

This commit fixes this behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit abb4ab076f)
2018-06-21 07:01:38 +02:00
Tobias Schramm
1863c38643 ramips: Add support for Mikrotik RouterBOARD RBM33g
This commit adds support for the Mikrotik RouterBOARD RBM33g.

=Hardware=

The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.

==Switch==

The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:

port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU

==Flash==

The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.

==PCIe==

The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.

Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:

PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11

==USB==

The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:

open: USB on PCIe 1 is active
closed: USB on rear USB port is active

==Power==

The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.

=Installation=

==Prerequisites==

A USB -> RS-232 Adapter and a null modem cable are required for
installation.

To install an OpenWRT image to the device two components must be built:

1. A openwrt initramfs image
2. A openwrt sysupgrade image

===initramfs & sysupgrade image===

Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.

==Installing==

**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**

Serial settings: 115200 8N1

The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:

1. Set up a dhcp server that points the bootfile to tftp server serving
   the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
   initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
   allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet

On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.

1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
   using scp.
2. Write openwrt to flash using "sysupgrade
   openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"

Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.

Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:55:10 +02:00
Tobias Schramm
7381ed3d01 ramips: Add lzma-loader targets
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:55:10 +02:00
Tobias Schramm
5529e71357 ramips: Add support for mt7621 to lzma-loader
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2018-06-21 06:55:10 +02:00
Deng Qingfang
615186d415 ramips: fix Newifi D1 mtd partition
Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-06-21 06:55:10 +02:00
INAGAKI Hiroshi
da318f3522 ramips: add support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
  - MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新(アップデート)")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 22:46:04 +02:00
INAGAKI Hiroshi
afe0320ffc ramips: add support for I-O DATA WN-GX300GR
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.

Specification:

- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 115200 bps (U-Boot, OpenWrt)

Flash instruction using initramfs image:

1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 22:45:36 +02:00
INAGAKI Hiroshi
a1373bc6fc ipq806x: add support for NEC Aterm WG2600HP
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

Specification:

- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
  - RX, TX, NC, GND, Vcc from power connector side
  - baudrate: 115200 bps

Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
  /dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
  fw_setenv ipaddr "192.168.0.1"
  fw_setenv serverip "192.168.0.2"
  fw_setenv autostart "yes"
  fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
  bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-06-19 22:44:27 +02:00
Mathias Kresin
3a99b278cd ramips: mt7621: fix wireless package selection
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-19 22:44:27 +02:00
Tomasz Maciej Nowak
a21210fbb7 mvebu: reduce speed to gen1 for espressobin pcie
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:

 OF: PCI: host bridge /soc/pcie@d0070000 ranges:
 OF: PCI:   MEM 0xe8000000..0xe8ffffff -> 0xe8000000
 OF: PCI:    IO 0xe9000000..0xe900ffff -> 0xe9000000
 advk-pcie d0070000.pcie: link up
 advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
 pci_bus 0000:00: root bus resource [bus 00-ff]
 pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
 pci_bus 0000:00: root bus resource [io  0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
 pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
 pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
 [...]
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 ath9k 0000:00:00.0: enabling device (0000 -> 0002)
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
 ath9k 0000:00:00.0: request_irq failed
 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
 ath9k: probe of 0000:00:00.0 failed with error -22

The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):

 OF: PCI: host bridge /soc/pcie@d0070000 ranges:
 OF: PCI:   MEM 0xe8000000..0xe8ffffff -> 0xe8000000
 OF: PCI:    IO 0xe9000000..0xe900ffff -> 0xe9000000
 advk-pcie d0070000.pcie: link never came up
 advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
 pci_bus 0000:00: root bus resource [bus 00-ff]
 pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
 pci_bus 0000:00: root bus resource [io  0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
 advk-pcie d0070000.pcie: config read/write timed out

Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.

The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.

For the record, the iwlwifi and mt76 cards were not affected by this
issue.

1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 772258044b)
2018-06-19 12:54:24 +02:00
Tomasz Maciej Nowak
637d10d91e mvebu: add fix for armada 37xx cpufreq driver
Backport from stable kernel tree fixing clock leak.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 4ec8c8c23e)
2018-06-19 12:54:24 +02:00
Kevin Darbyshire-Bryant
8af649756f kernel: atm: pppoatm fix vc-mux connection failures
Backport a hot off the press upstream kernel ATM fix:

Preserve value of skb->truesize when accounting to vcc

"There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs. Ideally it would cover ATM too. It doesn't. Just
stashing the accounted value and using it in atm_raw_pop() is probably
the easiest way to cope."

The issue was exposed by upstream with:

commit 14afee4b6092fde451ee17604e5f5c89da33e71e
Author: Reshetova, Elena <elena.reshetova@intel.com>
Date:   Fri Jun 30 13:08:00 2017 +0300

    net: convert sock.sk_wmem_alloc from atomic_t to refcount_t

But an earlier commit left the ticking timebomb:

158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()

Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging
assistance and to David Woodhouse <dwmw2@infradead.org> for further
guidance, cajoling & patience in interpreting the debug I was giving him
and producing a fix!

Fixes FS#1567

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit d600de3ddd)
2018-06-18 21:29:34 +02:00
Vincent Wiemann
b85e150182 mips: fix dynamic ftrace
The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as
dynamic ftrace depends on -mlong-calls.
See http://patchwork.linux-mips.org/patch/675/
Thus we always set -mlong-calls if the kernel is being
compiled with dynamic ftrace support.

Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
(cherry picked from commit 076d2ea682)
2018-06-18 21:21:56 +02:00
Thomas Nixon
b3b81d9d2a ar71xx: add kmod-usb-ehci to fix USB on RB hAP AC
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
(cherry picked from commit bb71a3f27e)
2018-06-18 21:21:56 +02:00
Chen Minqiang
520c656d7b ipq40xx: essedma: fixup ip align
This fixup ip align in essedma driver rx path
see cat /proc/cpu/alignment
which reports alignment-fixups without this fix.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit 8f804f42d5)
2018-06-18 21:21:55 +02:00
John Crispin
370078466c ipq806x: D7800 only has a single sata port
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit ee1dbffeed)
2018-06-18 21:21:55 +02:00
Jeremiah McConnell
ae0712ae8f mvebu: backport ahci_mvebu errata patchset
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.

Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.

These patches backport the workaround from 4.17.

Signed-off-by: Jeremiah McConnell <miah@miah.com>
(cherry picked from commit e820455198)
2018-06-18 21:21:55 +02:00
Hauke Mehrtens
56f66be113 mediatek: mt7622: Do not deactivate CONFIG_BLK_DEV
zram.ko needs CONFIG_BLK_DEV activated and it is by default for all
other targets in OpenWrt.

This makes zram.ko compile again.
Compile tested only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6745af9a0d)
2018-06-18 21:21:55 +02:00
Hauke Mehrtens
db969b2f30 mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53
Neon and vfpv4 are mandatory extensions in the ARM64 instruction set
now, do not activate them explicitly. GCC will make use of these
extension now by default.

This makes it possible to share the toolchain with other Cortex A53
SoCs.
Compile tested only.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 10ce015c65)
2018-06-18 21:21:55 +02:00
Jeremiah McConnell
1bb1239c28 mvebu: enable SATA port multiplier support
Some of the Marvell targets have functional SATA port multiplier
support, which is required for multi-bay eSATA enclosures.  Enable
kernel support by setting CONFIG_SATA_PMP.

Closes: FS#1232 and FS#547

Signed-off-by: Jeremiah McConnell <miah@miah.com>
(cherry picked from commit 390c4df2c0)
2018-06-18 21:21:54 +02:00
Sven Eckelmann
503f7f0614 ar71xx: Fix offset to WMAC address for 8devices Lima
The ART partition of the Lima board stores exactly three mac addresses:

* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac

The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.

Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 4f6320704f)
2018-06-18 21:21:54 +02:00
Rosen Penev
697d7fd000 ipq806x: Limit NR_CPUS to 2
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:

RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2

Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit fff65dbe24)
2018-06-18 21:21:54 +02:00
John Crispin
29ba45bb35 mediatek: add missing symbols for mt7622
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 55f3731002)
2018-06-18 21:21:54 +02:00
John Crispin
0506039845 mediatek: add missing symbols
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit de6162e832)
2018-06-18 21:21:54 +02:00
John Crispin
8e662b9654 mediatek: add mt7622 subtarget
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 51740777fb)
2018-06-18 21:21:53 +02:00
John Crispin
da8fc1511f mediatek: backport upstream mediatek patches
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 050da2107a)
2018-06-18 21:21:53 +02:00
Daniel Golle
6f398aa762 oxnas: reboot target
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.

Functional issues:
 * PCIe won't come up (hence no USB3 on Shuttle KD20)
 * I2C bus of Akitio myCloud device is likely not to work (missing
   debounce support in new pinctrl driver)

Code-style issues:
 * plla/pllb needs further cleanup -- currently their users are writing
   into the syscon regmap after acquireling the clk instead of using
   defined clk_*_*() functions to setup multipliers and dividors.
 * PCIe phy needs its own little driver.
 * SATA driver is a monster and should be split into an mfd having
   a raidctrl regmap, sata controller, sata ports and sata phy.

Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(squash-picked commit 17511a7ea8 and commit dcc34574ef from master)
2018-06-18 18:44:14 +02:00
Koen Vandeputte
4f765922f0 kernel: bump 4.9 to 4.9.109 for 18.06
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 15:28:48 +02:00
Koen Vandeputte
6cf00dcf7d kernel: bump 4.14 to 4.14.49 for 18.06
Refreshed all patches

Compile-tested on: cns3xxx, imx6, x86-64
Runtime-tested on: cns3xxx, imx6, x86-64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 06:42:29 +02:00
Koen Vandeputte
4121018b3f kernel: bump 4.9 to 4.9.108 for 18.06
Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-06-18 06:42:18 +02:00
Maxim Anisimov
5881e2434f ramips: add support for TP-Link TL-WR842N v5
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.

Specification:

- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch

Flash instruction:

The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2018-06-16 10:16:38 +02:00
David Bauer
be799e8c2a ramips: use phytpt trigger for mt76 wireless
With this change, the LED trigger is independent from the (wireless)
netdev name. The (wireless) netdev name can be easiliy changed in
OpenWrt and would require an update of the netdev trigger settings each
time it is done.

This change is (for now) applied only to MT7628 devices from TP-Link, as
we only had the possibility to test this change against two of those
devices, namely a TL-WR841 v13 and a Archer C50 v3.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-16 10:16:38 +02:00
lbzhung
3b8e53f6af ramips: fix mt7688 watchdog register base addr
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.

Set the correct register address and size in the dtsi file to get the
watchdog working.

Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-16 10:16:38 +02:00
Felix Fietkau
18f18a2054 kernel: fix conntrack fixup of offloaded flows on timeout
Fixes excessively long conntrack timeout of short lived connections

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-14 11:48:05 +02:00
Felix Fietkau
244fd1aac6 kernel: fix conntrack leak for flow_offload connections
This was caused by a race condition between offload teardown and
conntrack gc bumping the timeout of offloaded connections

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-14 11:47:58 +02:00
Felix Fietkau
8e1269c29d kernel: allow hardware NAT offload drivers to keep a priv pointer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-14 11:47:40 +02:00
Matthias Badaire
21a12f4269 ramips: fix network config for ravpower wd03
This device has only one ethernet port.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[add the existing eth0 as lan block, shorten commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-09 13:46:01 +02:00
David Bauer
46e232d8a1 ar71xx: use Power-LED as Diag-LED on FRITZBox 4020
This commit makes use of the Power-LED as Diag-LED, allowing the LED to
work as a status indicator.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:46:01 +02:00
David Bauer
433fb7d2c7 ar71xx: fix AVM package selection
The AVM package selection partially broke with the addition of the
FRITZ!Box 4020. This commit restores the intended behavior.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-06-09 13:46:01 +02:00
Koen Vandeputte
b8a5fc207a ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boards
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.

Toggling a gpio selects the output to which USB is connected.

Since kernel 4.9, gpio base is rounded up to a value of 32.

Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.

But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.

Switching the USB port to mPCIe now shows my modem is correctly discovered again:

[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11

Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 55b4b1eba0)
2018-06-08 09:33:44 +02:00
Stijn Tintel
0c59c9c9db kernel: fix 811-pci_disable_usb_common_quirks.patch
The kernel bump wrongly modified the patch
generic/pending-4.14/811-pci_disable_usb_common_quirks.patch.
Sync it from master.

Fixes: 1199a91095 ("kernel: bump 4.14 to 4.14.48 for 18.06")

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-06-07 16:18:55 +03:00
Stijn Segers
1199a91095 kernel: bump 4.14 to 4.14.48 for 18.06
Refreshed patches. The following patches were upstreamed and have been deleted:

* target/linux/lantiq/patches-4.14/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
* target/linux/generic/pending-4.14/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
* target/linux/generic/pending-4.14/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
* target/linux/generic/pending-4.14/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch

Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2018-06-07 09:03:24 +02:00
Stijn Segers
6f8eb1b50f kernel: bump 4.9 to 4.9.106 for 18.06
Refreshed patches. The following patches were upstreamed and have been deleted:

* target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
* target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
* target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
* target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2018-06-07 09:03:05 +02:00
Matthias Schiffer
805e59cdcc
ar71xx: switch CPE/WBS 210/510 to okli-loader
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.

While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.

Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.

Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:27:59 +02:00
Matthias Schiffer
aa87a5cffb
ar71xx: make loader-okli build step more generic
Add support for different loader types.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:27:59 +02:00
Matthias Schiffer
9310304d1a
ar71xx: lzma-loader: constify kernel argv array
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:27:59 +02:00
Matthias Schiffer
7128fe094f
ar71xx: lzma-loader: set page size to 4KB
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:27:59 +02:00
Matthias Schiffer
e5301885bc
ar71xx: lzma-loader: move padding workaround to gzip step
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.

This approach had two issues:

- The padding was only working when .data was non-empty (otherwise the
  section would become NOBITS, omitting it in the binary). .data was only
  empty when no CMDLINE was set, leading to further workarounds like
  fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
  workaround was only effective because a missing "const" led to the kernel
  argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
  uncompressed .bin and .elf loaders. The prevented embedding the kernel
  cmdline in the loader for non-gz loader types.

To fix both issues, move the creation of the padding from the linker script
to the gzip step.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-06-06 22:27:59 +02:00
Felix Fietkau
b295e3a18d kernel: backport patch to fix dst handling for offloaded connections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-06-05 10:19:35 +02:00
John Crispin
ba204d941c Revert "ramips: Move PCI driver to files directory"
This reverts commit a098a78a33.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 21:03:27 +02:00
John Crispin
324ea1f414 Revert "ramips: Remove redundant owner assignment"
This reverts commit 2ad4daf579.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 21:03:27 +02:00
John Crispin
82cfec057f Revert "ramips: improve interrupt mapping"
This reverts commit 5f7396ebef.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 21:03:27 +02:00
John Crispin
b9555a9831 Revert "ramips: remove conditional compilation."
This reverts commit 1f78625714.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 21:03:27 +02:00
John Crispin
a973a0a38b Revert "ramips: remove unnecessary resource details."
This reverts commit edea934799.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 21:03:27 +02:00
John Crispin
0bfb41a55a Revert "ramips: pci: sync with staging driver"
This reverts commit e07baec9fa.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 21:03:27 +02:00
John Crispin
bf5829ddf9 Revert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"
This reverts commit 8ccdf809c0.

Signed-off-by: John Crispin <john@phrozen.org>
2018-06-01 21:03:27 +02:00
Michael Gray
0037b13480 mvebu: fix broken console on WRT32X (venom)
The console bootarg is being corrupted on boot, causing various issues
including broken sysupgrade.
Utilising the bootargs mangle patch from other targets, hardcode the console
arguments and fetch the rootfs from the bootloader.

Kernel command line: console=ttyS0,115200 root=/dev/mtdblock8

Bootloader command line (ignored): console= root=/dev/mtdblock8

Please cherry pick to 18.06 too

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
(cherry picked from commit 4fdc6ca31b)
2018-06-01 21:03:27 +02:00
Rosen Penev
17eb0c4872 ramips: Use generic board detect for GnuBee devices
This is a port of an old commit from mkresin's tree:

09260cdf3e9332978c2a474a58e93a6f2b55f4a8

This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 9685f39787)
2018-05-30 13:00:50 +02:00
Rosen Penev
8ccdf809c0 ramips: Fix WiFi after 5f7396ebef
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.

eg. 2.4GHz working but not 5GHz.

As all of these dts entries are already specified in mt7621.dtsi, remove
them.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 02f815d190)
2018-05-30 08:07:12 +02:00
John Crispin
fa0275bd90 target/linux: drop anything not on v4.9 or v4.14
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 17:24:31 +02:00
John Crispin
76ba98d9b0 ath79: drop, its not ready for a release yet
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-24 17:24:31 +02:00
Rosen Penev
45456fe0c8 ramips: Fix up GnuBee PC1 DTS file a little
There's nothing connected to i2c on this board, so remove it.

Also edited the gpio group to match the PC2 as they're the same.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 8c818fa1f0)
2018-05-24 17:24:31 +02:00
Mirko Parthey
ac24a026d2 brcm47xx: add switch port mapping to Asus WL-500W
Switch ports 0..3 are connected to external ports LAN{1..4} in sequence,
switch port 4 is not used, and switch port 5 is connected to the CPU.
The WAN port is attached to the CPU's second network interface; it has no
connection to the internal switch.

Reuse the "Dell TrueMobile 2300" entry, which describes the same mapping.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
(cherry picked from commit 7ac238fc98)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
f39a7179bc ipq806x: drop "mtd: nand: add Winbond manufacturer and chip"
The W25N01GV NAND is currently not used in any ipq806x device.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit a436ef992d)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
63c1719988 ipq806x: drop linux 4.9 support
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 2819732219)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
2301bbdf88 ipq806x: switch to linux 4.14
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 18e9ed2482)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
1df8281737 ipq806x: remove spi-nor from r7800 dts
There's no spi-nor in R7800, so disable unequipped interfaces.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit 8c1c1c4874)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
eac20ce427 ipq806x: remove rpm pinctrl from board dts
These pins seem to be used by hw exclusively, so claiming it in
kernel causes an error in syslog in k4.14+.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit 96cd31655d)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
c52cd4d8c3 ipq806x: fix EA8500 switch control
EA8500 has pcie2 slot unequipped.
By EA8500 hw design default pcie2 reset gpio (gpio63) is used to
reset the switch. That's why enabling pcie2 brings the switch into
a working state.

So let's just control the gpio63 without enabling the pcie2 slot.

We have to remove the pcie2_pins node so the gpio63 is not defined
twice. Because pcie2 node has a reference to pcie2_pins we have to
remove it as well.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit 7f694ef3d9)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
bdddbe9718 ipq806x: move mmc specific nodes into v1.0 dtsi
These nodes are common for all revisions so put it into SoC v1.0
dtsi file.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit 7a4f9c5993)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
8458febc01 ipq806x: fix pcie tx termination offset
According to GPL tarballs and QSDK related branch tx termination
offset for ipq8064 SoC version >= 2.0 should be equal to 0 and
not 7.

https://github.com/paul-chambers/netgear-r7800/blob/master/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L1682-L1685

Fix this.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit fbedc2213c)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
a64a36308c ipq806x: apply updated USB PHY settings to v2.0 SoC
USB PHY power settings introduced for ipq8065 SoC with commit
644a0d5 "ipq8065: adjust SS USB PHY power settings"

According to that commit msg and in correspondence to GPL tarballs
and related QSDK branch those settings are applied to ipq8064
SoCs of version >= 2.0.

https://github.com/paul-chambers/netgear-r7800/blob/master/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2507-L2514

Now as we have clarified that mass market boards are of SoC v2.0
move those USB PHY settings from ipq8065 (v3.0 SoC) dtsi to
ipq8064 v2.0 dtsi.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit d4b98c38c6)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
715ff75b1b ipq806x: reference ipq8065 as ipq8064 v3.0
ipq8065 is ipq8064 v3.0
> socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0,  hw_plat_ver=65536

Include dtsi accordingly and remove the unneeded qcom-ipq8065-v1.0.dtsi

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit e16f9abf6b)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
a6d825d735 ipq806x: move mass market ipq8064 to v2 dtsi
According to OEM bootlog entry mass market devices are ipq8064 SoC
v2.0:
> socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0,  hw_plat_ver=65536

I've checked C2600, EA8500 and VR2600v but couldn't find other
boards bootlog. I think it's safe to assume that other boards are
also v2.0. R7500 may be an exception because it was the first
device to hit the market.

So switch to v2.0 dtsi.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit 067036e875)
2018-05-24 17:24:31 +02:00
Pavel Kubelun
d629e013ef ipq806x: introduce ipq8064 SoC v2 dtsi
According to QCA internal numbering there are 3 versions of
ipq8064/5 SoC:
ipq8064 v1.0 - probably ipq8064 evaluation boards only
ipq8064 v2.0 - probably ipq8064 mass market boards only
ipq8064 v3.0 - aka ipq8065, boards based on ipq8065.

Each next revision includes configuration differences from
previous revision and adds something new.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit adbdf78049)
2018-05-24 17:24:31 +02:00
Marc Benoit
65de91a884 kernel: iqp806x low latency kernel does not boot
It keeps failing (R7800) with the stack trace below

BUG: scheduling while atomic: kworker/0:1/26/0x00000002

(unwind_backtrace) from [<c02121d0>] (show_stack+0x10/0x14)
(show_stack) from [<c03932e4>] (dump_stack+0x7c/0x9c)
(dump_stack) from [<c0239b90>] (__schedule_bug+0x5c/0x80)
(__schedule_bug) from [<c05b7260>] (__schedule+0x50/0x3f4)
(__schedule) from [<c05b76a8>] (schedule+0xa4/0xd4)
(schedule) from [<c05ba430>] (schedule_hrtimeout_range_clock+0xc8/0x100)
(schedule_hrtimeout_range_clock) from [<c05ba480>]
       (schedule_hrtimeout_range+0x18/0x20)
(schedule_hrtimeout_range) from [<c05b9f78>] (usleep_range+0x48/0x50)
(usleep_range) from [<c03f333c>] (__clk_hfpll_enable+0x44/0xd0)
(__clk_hfpll_enable) from [<c03f3474>] (clk_hfpll_set_rate+0xac/0xc4)
(clk_hfpll_set_rate) from [<c03ec390>] (clk_change_rate+0xf4/0x1fc)
(clk_change_rate) from [<c03ec510>] (clk_core_set_rate_nolock+0x78/0x94)
(clk_core_set_rate_nolock) from [<c03ec54c>] (clk_set_rate+0x20/0x30)
(clk_set_rate) from [<c0424168>] (dev_pm_opp_set_rate+0x190/0x26c)
(dev_pm_opp_set_rate) from [<c04a8548>] (set_target+0x40/0x108)
(set_target) from [<c04a4.140>] (__cpufreq_driver_target+0x3f4/0x488)
(__cpufreq_driver_target) from [<c04a7494>] (od_dbs_timer+0xcc/0x154)
(od_dbs_timer) from [<c04a7998>] (dbs_work_handler+0x2c/0x54)
(dbs_work_handler) from [<c02309e8>] (process_one_work+0x1c0/0x2f0)
(process_one_work) from [<c02319a8>] (worker_thread+0x2a4/0x404)
(worker_thread) from [<c0235944>] (kthread+0xd8/0xe8)
(kthread) from [<c020eef0>] (ret_from_fork+0x14/0x24)

Signed-off-by: Marc Benoit <marcb62185@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit e40db2907e)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
e567d313b6 ipq806x: define KERNEL_SIZE in KB instead of byte for the image generation
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 05f53eecca)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
1b39b665c3 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500v2
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500v2.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit c3af761e47)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
3ec4921c16 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 R7500
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit c228bbe616)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
0882a4cf25 ipq806x: increase kernel partition size for the Netgear Nighthawk X4 D7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 D7800.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Tathagata Das <tathagata@alumnux.com>
(cherry picked from commit 45b8a7c1a6)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
ec7d974055 ipq806x: increase kernel partition size for the TP-Link Archer VR2600v
The default image does not fit 2 MB anymore, expand kernel partition
to 3 MB.

Upgrading should work transparently via sysupgrade in both directions.
Another option would be to merge "kernel" and "rootfs" into a single
"firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the
sizes of the existing partitioning has been deemed safer in the absence
of an actual runtime test on an affected device; the maximum for rootfs
changes from 10.4 MB to 9.4 MB.

This change follows the example for the TP-Link Archer C2600, but has
not been runtime tested on a TP-Link Archer VR2600v.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Sebastian Quilitz <zeraphim@x-pantion.de>
(cherry picked from commit 0c967d92b3)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
742ac017ba ipq806x: increase kernel partition size for the TP-Link Archer C2600
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.

Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.

Run-tested on TP-Link Archer C2600.

Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit b72b36653a)
2018-05-24 17:24:31 +02:00
Stefan Lippers-Hollmann
66871d9c62 ipq806x: increase kernel partition size for the Netgear r7800
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.

This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.

WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.

This patch is based on a corresponding change by Pavel Kubelun
<be.dissent@gmail.com> and has been tested by Michael Yartys
<michael.yartys@protonmail.com>

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit dc50694bd1)
2018-05-24 17:24:31 +02:00
Ram Chandra Jangir
27223c0761 ipq806x: cleanup kernel config
Disable MSM8960, MSM8974 and APQ8084
 - since these are different SoC's than IPQ806x
Removed unrequired serial configs
 - since ipq806x uses SERIAL_MSM only

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 7ac6697fe2)
2018-05-24 17:24:31 +02:00
Ram Chandra Jangir
d805812e75 ipq806x: add kernel 4.14 support
- Rebased the patches for 4.14
 - Dropped spi-qup and 0027, 0028, 0029
   clk patches since it's already included
   in upstream.

 Tested on IPQ AP148 Board:
  1) NOR boot and NAND boot
  2) Tested USB and PCIe interfaces
  3) WDOG test
  4) cpu frequency scaling
  5) ethernet, 2G and 5G WiFi
  6) ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 93dd2f7211)
2018-05-24 17:24:31 +02:00
David Bauer
9361c359e4 ipq40xx: add eva-image for FRITZ!Box 4040
This commit adds an EVA flashable image for the FRITZ!Box 4040.

The image contains the U-Boot with OpenWRT appended to it. This way we
remove the need to use UART for initial flashing.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 70e6ea319d)
2018-05-24 17:24:31 +02:00
David Bauer
701a7b1c86 ramips: change wifi led trigger for Archer C50v3
This commit alters the TP-Link Archer C50v3 LED settings to use the phy
trigger instead of the netdev one. This way the WiFi status is displayed
even if the wifi interface name is altered.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ce91c85e01)
2018-05-24 17:24:31 +02:00
David Bauer
53507cef82 ramips: fix Archer C50v3 LED mapping
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 35d00d9a41)
2018-05-24 17:24:31 +02:00
Chuanhong Guo
991ec8e5b2 ar71xx: Add support for PISEN TS-D084
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0

Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit a789c0f491)
2018-05-24 17:24:31 +02:00
Sergey Ryazanov
23cdf9f246 kernel: enable THIN_ARCHIVES by default
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 67a3cdcbb0)
2018-05-24 17:24:31 +02:00
Sergey Ryazanov
16e0866a74 kernel: enable FUTEX_PI by default
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit bdc2b58c4b)
2018-05-24 17:24:31 +02:00
Sergey Ryazanov
1f26cfc92b kernel: enable EXPORTFS by default
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit a08b0d0c31)
2018-05-24 17:24:31 +02:00
Sergey Ryazanov
294a45adbe kernel: disable DRM_LIB_RANDOM by default
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 978543a246)
2018-05-24 17:24:30 +02:00
Sergey Ryazanov
1deadfe3de kernel: disable DMA_{NOOP|VIRT}_OPS by default
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit ead26e9db6)
2018-05-24 17:24:30 +02:00
Sergey Ryazanov
95922e16d7 kernel: disable ARCH_WANTS_THP_SWAP by default
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit f928c338ad)
2018-05-24 17:24:30 +02:00
Evgeniy Didin
2c9e3736f4 arc770: remove source-only
In commit 8b9cdebc9c ("arc770: mark as source-only") arc770 was marked
as source-only because of iproute2 compile issues.
With uClibc-ng version 1.0.30 issues with iproute2 were fixed.
Lets remove "source-only" for arc770 as soon as uClibc-ng version
will be updated to 1.0.30. Patch for uClibc-ng is here:
https://patchwork.ozlabs.org/patch/917547/

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
(cherry picked from commit a2418dba02)
2018-05-24 17:24:30 +02:00
Hauke Mehrtens
9e4f4e1a1f ar71xx: Fix build for dap-1330-a1 board
Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.

This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ae8ff1c65c)
2018-05-24 17:24:30 +02:00
Sergey Ryazanov
8f2ac5c085 ath25: drop 4.9 kernel support
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 06116473cc)
2018-05-24 17:24:30 +02:00
Sergey Ryazanov
5d3b216d21 ath25: switch to 4.14 kernel
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 5191ea5621)
2018-05-24 17:24:30 +02:00
Sergey Ryazanov
586872da59 ath25: add kernel 4.14 support
Copy and refresh patches and config from 4.9, no more work is need.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 3d69857ac1)
2018-05-24 17:24:30 +02:00
Alif M. Ahmad
0d6d8d71fc x86: disable CONFIG_EFI_VARS
Disable CONFIG_EFI_VARS, since it suffers from sysfs limitation (no
support for variable longer than 1024 bytes).

kmod-fs-efivarfs is the replacement of this, which enables mounting
efivarfs file system and doesn't suffer from 1024 bytes limitation.

Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
(cherry picked from commit b0a51dab8c)
2018-05-24 17:24:30 +02:00
YuheiOKAWA
0f35193aec ramips: add support for YUKAI Engineering Inc. BOCCO
BOCCO is a communication robot provided by YUKAI Engineering Inc.

SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
(cherry picked from commit d91953cb53)
2018-05-24 17:24:30 +02:00
Michal Cieslakiewicz
1780f09ee3 ar71xx: WNDR3700: enable RFKILL function for Wifi button
Wifi button for WNDR3700 dual band routers has been renamed to "rfkill"
and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE
to support it 'out of the box' without additional tweaking.

Until this patch, button had been sending BTN_2 keycode which was
ignored by default (no action script present). To get expected behaviour
of switching radios on and off, user had to manually rename/link
'rfkill' script to name 'BTN_2' in /etc/rc.button directory.

This patch follows similar changes for other Netgear ar71xx routers,
for example WNR2000v3. It applies cleanly to both latest trunk and 17.01
branch. Tested on WNDR3700v1.

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
(cherry picked from commit 45dc530334)
2018-05-24 17:24:30 +02:00
Christian Lamparter
fff02093e6 brcm2708: add squashfs rootfs image
This patch adds a image with squashfs as the root filesystem.
A rootfs_data partition will be generated on the first boot
and placed inside the rootfs partition (just after the squashfs
image).

advantages:
 - it is possible to migrate from an existing -ext4
   installation and back via sysupgrade.
 - existing partition layout will not be lost.
 - slightly smaller image size.
 - support for attendedsysupgrade

disadvantages:
 - needs f2fs + tools as well. This is because fs-tools decides on the
   blocksize of the sdcard. So either f2fs or ext4 can get choosen as
   the rootfs_data filesystem (depends on the size of the root partition).
 - rootfs_data is placed into the rootfs partition. This makes
   it difficult for tools that expect a /dev/mmc0pX device.
   It also makes it difficult for data recovery tools since they
   might not expect to find a embedded partition or will be
   confused.

For people with existing build configurations: make sure to include mkf2fs
and f2fsck package into the image... Otherwise the new -squashfs image will
boot of a ram-overlay and won't keep the configurations after a reboot.

Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: Paul Spooren <spooren@informatik.uni-leipzig.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 707b6c815b)
2018-05-24 17:24:30 +02:00
Kristian Evensen
efdfb253d8 x86: Add APU3 reference to x86 board.d
There is a new APU-model available, APU3. The device is configured in
the same way as the APU1 and APU2, so the same LED/network setup can be
used.

I considered changing the case to pc-engines-apu*, but I chose to follow
the existing pattern and add the full board name.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
(cherry picked from commit 8f9baf5e1a)
2018-05-24 17:24:30 +02:00
Christian Lamparter
644f65afe1 apm821xx: backport and reassign crypto4xx patches
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:

crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx

The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 16e39624b7)
2018-05-24 17:24:30 +02:00
Christian Lamparter
f47b5802b5 apm821xx: don't select swconfig for the MR24
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e6e51ce87f)
2018-05-24 17:24:30 +02:00
Roman Yeryomin
f882f4474f ipq40xx: fix ethernet on ap-dk01.1
Not sure how it worked before but ethernet is disabled
by default in ipq4019 dtsi.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
(cherry picked from commit 1f42deec8e)
2018-05-24 17:24:30 +02:00
Daniel Gonzalez Cabanelas
9373836f94 brcm63xx: Tune the network configuration for several routers
- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit fbbb977772)
2018-05-24 17:24:30 +02:00
Koen Vandeputte
e39414ed07 kernel: bump 4.14 to 4.14.43 for 18.06
Refreshed all patches

Dropped upstreamed patches:
522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch
523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch
525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch
527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch

updated patches:
524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch
030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch

Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718

Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-24 16:04:09 +02:00
Koen Vandeputte
2b7289cd3b kernel: bump 4.9 to 4.9.102 for 18.06
Refreshed all patches

Added new ARM64 symbol: ARM64_ERRATUM_1024718

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-05-24 16:03:58 +02:00
Felix Fietkau
72ebcef5be netfilter: fix hardware offload regression (FS#1551)
The relevant code needs to be enabled even if flow table support is only
compiled as module

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-17 09:00:55 +02:00
Mathias Kresin
617b7e9bf4 octeontx: make board.d files executable
Add the executable permission to the files to ensure they run on
firstboot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:43:57 +02:00
John Crispin
7e15e21766 Revert "ramips: mmc: Sync with staging drivers"
This reverts commit 2d401925b9.

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-15 12:42:40 +02:00
Wei Yongjun
87c254c87e staging: mt7621-eth: fix return value check in mt7621_gsw_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:46:08 +02:00
Wei Yongjun
edec251870 staging: mt7621-eth: fix return value check in mtk_connect_phy_node()
In case of error, the function of_phy_connect() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:53 +02:00
Wei Yongjun
c4ae54dfab staging: mt7621-eth: fix return value check in mtk_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-15 06:45:34 +02:00
Rosen Penev
e07baec9fa ramips: pci: sync with staging driver
This is an amagalmation of two upstream commits dealing with whitespace
and dead code removal. I'm synching instead of having two separate commits
as they go out of order compared to previous commits here.

Tested on GnuBee PC1.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:45:07 +02:00
Rosen Penev
2d401925b9 ramips: mmc: Sync with staging drivers
Mostly whitespace cleanups. Some unneeded code was removed.

MMC init was also moved to the probe function as in
6069bdd087

The cleanup commits are over 100, making it hard to do them individually.

Tested on GnuBee PC1 with an SD card being used as swap.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-15 06:44:48 +02:00
Matthias Badaire
a0685deec4 ramips: Add i2c support for mt7620n
I2c is supported on mt7620n like on mt7620a when checking the datasheet

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-15 06:39:46 +02:00
Alberto Bursi
e09d4c850d kirkwood: support for buttons in Audi and Viper
Both these devices have a wps and a reset button on
GPIO pins, which need kmod-gpio-button-hotplug
package to work.

Add this package to their default package config.

Troubleshooted and tested on a Viper.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2018-05-15 06:39:37 +02:00
Johann Neuhauser
c15dfbeea0 ath79: fix gmac compatible in ar9330.dtsi and ag71xx_setup_gmac_933x
1. compatible property in node gmac was wrong

2. ag71xx_setup_gmac_933x should use np of gmac-config and
   not the pointer to gmac. gmac is only used for the reg address.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-05-15 06:38:07 +02:00
Michael Gray
bfbdeeb3de mvebu: add support for WRT32X (venom)
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.

Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)

Flash instruction:
Apply factory image via web-gui.

Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
2018-05-14 17:20:10 +02:00
Linus Walleij
1f56417e6b gemini: Augment DIR-685 device tree for RTL8366RB
This makes the ethernet and RTL8366RB come up on the
D-Link DIR-685.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:10 +02:00
Linus Walleij
3b48111df9 gemini: create zImage for DIR-685
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-14 16:24:09 +02:00
NeilBrown
edea934799 ramips: remove unnecessary resource details.
These resources are extracted from devicetree, so they aren't
needed here.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:07 +02:00
NeilBrown
1f78625714 ramips: remove conditional compilation.
Code currently defines:

and then compiles code only if they are defined.
We might want to disable some of these via devicetree one
day, but for now just remove the #defines and the
conditions - all the code for different ports is
easy to identify.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:24:04 +02:00
NeilBrown
5f7396ebef ramips: improve interrupt mapping
As the Interrupts for the PCI adapters are listed in
devicetree we shouldn't need to have them explicit in the code.

The simplest way to do this is to use of_irq_parse_and_map_pci()
and specify an interrupt-map which identifies the different
PCI hosts by bus/slot numbers.
This has the advantage that the hwirq number are mapped to virq
numbers for us, so the ugly hack can go.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:59 +02:00
Christian Lütke-Stetzkamp
2ad4daf579 ramips: Remove redundant owner assignment
Remove the owner assignment form the platform driver as
platform_driver_register() already initializes the owner.
Found using coccinelle.

Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-05-14 16:23:36 +02:00
Rosen Penev
a098a78a33 ramips: Move PCI driver to files directory
This will make it easier to port upstream code.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-05-14 15:55:17 +02:00
Jo-Philipp Wich
aadca035bc at91: sama5d4: fix bad mkubifs options
Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we
do not support it in mkfs.ubifs. Attempting to use LZO compression results
in "Error: bad compressor name".

The build system also appends an explicit "--compr=zlib" to the mkfs command
line, turning the "-x" flag into a no-op anyway.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-13 18:33:47 +02:00
Rafał Miłecki
404508001e kernel: use accepted version of bcm47xxpart fix commit
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:53:44 +02:00
Rafał Miłecki
070693477a kernel: backport mtd patch for minor partitioning cleanup
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 23:14:07 +02:00
Felix Fietkau
a3096b4b33 kernel: fix build error in flow offload code with CONFIG_NETFILTER=n
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-12 22:28:00 +02:00
Rafał Miłecki
02225f5763 bcm53xx: backport the first bunch of 4.18 BCM5301X patches
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-12 15:38:55 +02:00
Jo-Philipp Wich
cf7a88cf5a at91: cleanup kernel configurations
The subtarget configurations contained a lot of reduntant symbols, arbitrary
overrides and symbols set to =m.

Remove most of these redundant settings to shrink the subtarget configurations
to a manageable size.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 18:24:00 +02:00
Jo-Philipp Wich
f23326eb76 at91: sama5d2: remove CONFIG_XZ_DEC override
Fixes the following error spotted by the buildbot:

    Package kmod-fs-squashfs is missing dependencies for the following libraries:
    xz_dec.ko

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:40:34 +02:00
Jo-Philipp Wich
0167f53b9d at91: add missing config symbols
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 16:01:26 +02:00
Jo-Philipp Wich
d8c7cd9cb1 kernel: rtl8366_smi: guard of_mdiobus_register() call
Make the call to of_mdiobus_register() dependant on CONFIG_OF to avoid
pulling in an unwanted dependency on of_mdio.ko.

Fixes: 3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2018-05-11 15:07:56 +02:00
Piotr Dymacz
ce4d2fb5cc ar71xx: fix and improve ALFA Network Tube2H support
Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).

Fixes: FS#1532

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2018-05-09 20:32:47 +02:00
Matthias Schiffer
db34cdf6c5
ath79: Ubiquiti Airmax M: add relocate-kernel to invalidate cache
Apply ar71xx fix for broken Ubiquiti bootloader to ath79 as well.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-05-08 21:14:24 +02:00
Felix Fietkau
6069bdd087 ramips: move mtk-mmc init to probe function to avoid breaking NAND flash
The driver messes with the pin control settings - MMC and NAND are
mutually exclusive

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-08 17:56:04 +02:00
Felix Fietkau
f95a4aa565 ramips: clean up the mt7621 nand flash driver hacks, add support for the xiaomi mir3g flash chip
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-08 17:56:04 +02:00
Rafał Miłecki
97f3c0f041 brcm47xx: switch to the kernel 4.14
The biggest (and the only?) disadventage of this is obviously an
increased image size.

For mips74k the size of vmlinux goes up from 4186684 B to 4701436 B.
Most devices use LZMA compressed kernel so probably more important is
vmlinux.lzma size which goes up from 1342945 B to the 1508498 B.

Still this isn't something that should stop target kernel bump. There
are various adventages of kernel 4.14. If kernel / image size is a
serious concern for anyone, it's perfectly possible to use previous
release which is pretty solid for the brcm47xx.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: Paul Wassi <p.wassi@gmx.at>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
2018-05-08 09:55:10 +02:00
Rafał Miłecki
f9dcdc7fef kernel: mark source kernel for netfilter backports
This helps keeping track on patches & adding new kernels in the future.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-08 09:42:07 +02:00
Davide Ammirata
004cc22e4e ramips: add support for mqmaker witi 512mb version
Splitted out the dts file and create the new dts for the 256 MByte RAM and
the 512 MB RAM version.

Migrate both versions to the common board detection.

The install the 512 MByte Version on a board running the 256 MByte image,
a forceful sysupgrade with the -F flag is required.

Signed-off-by: Davide Ammirata <list@davidea.it>
2018-05-07 18:54:23 +02:00
Matthias Badaire
5ef79af4f8 ramips: add support for Ravpower WD03
The RavPower WD03 is a battery powered SD card reader and a USB port.

Specifications:
SOC:     MediaTek MT7620N
BATTERY: 6000mah
WLAN:    802.11bgn
LAN:     1x 10/100 Mbps Ethernet
USB:     1x USB 2.0 (Type-A)
RAM:     PM Tech PMD708416CTR-5CN 32 MB
FLASH:   Holtek HT66F40 - 8 MB Flash
LED:     Power button and 4 leds to indicate power level of the
         battery (could not get control of that)
INPUT:   Power, reset button
OTHER:   USB SD-Card reader with card detect on GPIO#42

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Installation:
 - Download the sysupgrade image
 - Place it in the root of a clean TFTP server running on your computer.
 - Rename the image to "kernel" — be sure there is no file extension.
 - Plug the WD03 into your computer via ethernet.
 - Set your computer to use 10.10.10.254 as its IP address.
 - With your WD03 shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The WD03 (10.10.10.128) will look for your computer at 10.10.10.254
   and install the kernel file. Once it has finished installation of the
   kernel file, it will search for a (nonexistent) rootfs file — when it
   begins searching for this file, shut down the WD03 by holding the
   power button normally.
 - Start up your WD03 normally.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
2018-05-07 18:54:23 +02:00
Mathias Kresin
ef19747b6c lantiq: kernel 4.14: Remove reboot/remove reset asserts
Backport patch accepted upstream which removes the reset asserts of the
xrx200 gphy driver on reboot/remove.

While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't expect
these bits to be set, as they aren't during power on.

The asserts were a workaround for a wrong syscon-reboot mask. With a mask
set which includes the GPHY resets of the first reset register, the
resets of the second reset register arn't required any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 18:53:08 +02:00
John Crispin
99f10b193e ath79: drop dts/Makefile
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 15:01:12 +02:00
Russell Senior
4aacd6388a ath79: u-boot partitions should be read-only in dts
Some of the new ath79 device trees were missing read-only tags on the
u-boot partitions.  This adds the tags where previously missing.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-05-07 13:07:00 +02:00
Rafał Miłecki
4edd4cb2b3 ath79: use the new DT fixed partitions syntax
This new syntax is slightly better designed & uses "compatible" string.
For details see Documentation/devicetree/bindings/mtd/partition.txt .

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-07 12:57:47 +02:00
John Crispin
7fe77a5962 ath79: revert license change on upstream DTS files
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 12:52:03 +02:00
David Bauer
b6a4c67468 ar71xx: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.

SoC:   Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM:   Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi:  QCA9561 b/g/n 3x3 450Mbit/s
USB:   1x USB 2.0
IN:    WPS button, WiFi button
OUT:   Power LED green, Internet LED green, WLAN LED green,
       LAN LED green, INFO LED green, INFO LED red
UART:  Header Next to Black metal shield
       Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
       The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (LAN + WAN)
 - WiFi (correct MAC)
 - Installation via EVA bootloader
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Not working:
 - USB port

Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded
like following:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put openwrt-sysupgrade.bin mtd1

Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-05-07 10:42:26 +02:00
Rafał Miłecki
66c8afd115 ath79: relicense DTS files to the GPL 2.0+ / MIT
Some maintainers prefer DTS files licensed under permissive license like
MIT / BSD. As all DT bindings should be OS independent and DTS files are
pretty separated from Linux code it probably makes sense to share them
across projects.

The safest solution is to use dual licensing: that way it stays clear
these files can be used in GPL projects without depending on current
belief of licenses compatibility.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: John Crispin <john@phrozen.org>
2018-05-07 10:31:35 +02:00
John Crispin
53c474abbd ath79: add new OF only target for QCA MIPS silicon
This target aims to replace ar71xx mid-term. The big part that is still
missing is making the MMIO/AHB wifi work using OF. NAND and mikrotik
subtargets will follow.

Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 08:06:51 +02:00
John Crispin
3dc523f232 kernel: add OF support to rtl8355 driver
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-07 08:06:51 +02:00
Rafał Miłecki
ed00387dc5 bcm53xx: switch to the new/alternative SPI controller driver
This switches bcm53xx from spi-bcm53xx to the spi-bcm-qspi driver. The
later one was developed by Broadcom and is more advanced one. It
supports more modes, setting a speed, setting bits per word and uses
IRQs instead of polling.

This increases kernel size from 1808120 B to the 1811160 B (by 3040 B).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-05-07 07:56:38 +02:00
John Crispin
6e0ae87a98 ramips: disable spi full duplex on mt7621
Signed-off-by: John Crispin <john@phrozen.org>
2018-05-05 08:25:18 +02:00
Linus Walleij
6cd2e1f947 gemini: Add ethernet to DNS-313 and Wiliboard
This adds an interrim patch for v4.14 based on an
upstream commit to get ethernet working on D-Link DNS-313
(probably also on the Wiliboards)

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
ce93b05bf1 gemini: fix hard disk boot on D-Link devices
Since the D-Link devices boot from hard disk we need to
add the following changes to Gemini:

- Supply a bootarg in the device tree so we can boot from
  the right partition (/dev/sda4 on DNS-313)
- Disable forced command line in config so the kernel picks
  up the right bootargs from the device tree
- Enable EXT4 in the config as this is used for rootfs else
  we get nowhere, we cannot load this as a module because,
  well, it is supposed to be loaded from the root partition
  (chicken and egg problem).
- Enable jbd2 and mbcache (needed by ext4)

Also clean out the premature attempts to dynamically
modify the command line in the Image makefile: we should
pass this with the device tree bootargs instead, it works
much better.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
2c35bcffd0 gemini: add rtl8366rb to dir-685 board
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
af069fbd24 gemini: cleanup kernel config
Disable video and input drivers - they are needed only for one
board and can be enabled via modules if/when UI will be available.
Use LED drivers from packages.
Cleanup other things unnecessarily overriding defaults.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
91930c0f99 gemini: remove 4.4 support
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
6409b159e8 gemini: switch to 4.14
This introduces Device/ infrastructure and images
for all boards available upstream.

Changes from Linus submitted version:
- fix Raidsonic image generation
- remove redundant (old) image generation
- remove redundant header tool for dns313 board

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
4f74957584 gemini: add 4.14 support
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.

Tested on Raidsonic NAS4220B and D-link DNS-313.

ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed

ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
  of the v4.4 patches to separate (big) patches.

ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
  dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
  file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
  1 minute by default, if we have the hdparm tool installed

ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Roman Yeryomin
55c9aa27be gemini: rename files directory (preparation for 4.14)
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-05-05 06:57:00 +02:00
Sandeep Sheriker Mallikarjun
610770dc5b at91: refreshing kernel configurations.
refreshing kernel configurations for sama5 and legacy subtarget.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
27ca6cdc7b at91: Add SAMA5D2 PTC EK board
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
60750ab505 at91: reorganize at91 subtargets
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
  1. able to set neon flags to sama5d2 & sama5d4 subtargets.
  2. fix the make clean which removes all the subtargets in bin folder.
  3. able to configure kernel specific to subtarget.
  4. able to set vfpu4 flags to samad3 subtargets.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:22 +02:00
Sandeep Sheriker Mallikarjun
581f5e2392 at91: sdcard image with ext4 rootfs
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:21 +02:00
Sandeep Sheriker Mallikarjun
22c398d257 at91: Add SAMA5D27 SOM1 EK board
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:21 +02:00
Sandeep Sheriker Mallikarjun
130224cc47 at91: fix sdcard create image
copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-05-05 06:55:01 +02:00
Felix Fietkau
58f7b5b96c kernel: add missing in6_dev_put_clear call to an ipv6 network patch
Fixes "unregister_netdevice: waiting for lo to become free. Usage count = 1" messages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-05-02 15:32:07 +02:00
Rosen Penev
45219c1c0f kernel: Restrict dmesg output to root.
In typical OpenWrt setups, there are no other users that have a shell spawned for them by default.

This can be overriden by the kernel.dmesg_output syssctl.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-04-30 09:01:33 +02:00
Sandeep Sheriker Mallikarjun
2391d6a29e at91: sama5: remove neon and VFPv4 support
sama5d2 & samad4 have neon feature and sama5d3 does not have neon
feature due to which sama5d3 boot fails with error message Kernel
panic - not syncing: Attempted to kill init! exitcode=0x00000004.
removing neon & VFPv4 support to fix this

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-04-30 09:01:12 +02:00
Sandeep Sheriker Mallikarjun
80fe9bd71c at91: fix build error for wb50n.
when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.

Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
2018-04-30 09:01:12 +02:00
Simon Paterson
264feab1e7 ar71xx: Add userspace support for Mikrotik rb-2011iLS
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.

https://mikrotik.com/product/RB2011iLS-IN

Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
2018-04-30 09:01:12 +02:00
Koen Vandeputte
3435dbdc1c kernel: bump 4.14 to 4.14.37
Refreshed all patches

Compile-tested on: cns3xxx, imx6, octeon, ramips/mt7621, x86/64
Runtime-tested on: cns3xxx, imx6, octeon, ramips/mt7621, x86/64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[add extra tested targets to commit msg]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-04-30 09:07:53 +03:00
Mathias Kresin
3877550114 arm64: enable harden branch predictor
Enable the harden branch predictor for arm64 as it is recommend.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-27 21:34:18 +02:00
Mathias Kresin
25f47c7bf9 kernel: add missing config symbols
The harden branch predictor was backported for arm64 with 4.9.92-96.

Fixes: 9aa196e0f2 ("kernel: bump 4.9 to bump 4.9.96")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-27 21:34:00 +02:00
Felix Fietkau
67aec988c4 brcm47xx: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Felix Fietkau
771f1ca3ff brcm63xx: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Felix Fietkau
1de74df8b9 bcm53xx: drop linux 4.4 and 4.9 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-27 15:19:19 +02:00
Christo Nedev
50b0919628 brcm2708: Add support for raspberry pi 3 b+.
Signed-off-by: Christo Nedev <christo.nedev@me.com>
2018-04-27 09:59:33 +02:00
Rosen Penev
7912677086 kernel: Fix data corruption on some mips devices.
This is mainly a bug fix for multi-core MIPS systems where L1 caches besides the primary do not get flushed.

The most obvious problem is data corruption on SATA and USB devices where read requests are typically larger than the cacheline size.

This may also fix ar71xx systems that suffer from similar data corruption but I have not tested if it does.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2018-04-27 09:59:33 +02:00
Matthias Schiffer
d168c2cf81
ar71xx: Ubiquiti Airmax M: add relocate-kernel to invalidate cache
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.

As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2018-04-26 20:40:07 +02:00
Koen Vandeputte
6cd41b419c kernel: bump 4.14 to 4.14.36
Refreshed all patches.

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092
CVE-2018-1094
CVE-2018-1095

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2018-04-26 08:54:01 +02:00
Kevin Darbyshire-Bryant
9aa196e0f2 kernel: bump 4.9 to 4.9.96
Refresh patches, following required reworking:

ar71xx/patches-4.9/930-chipidea-pullup.patch
layerscape/patches-4.9/302-dts-support-layercape.patch
sunxi/patches-4.9/0052-stmmac-form-4-12.patch

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092

Tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Arjen de Korte <build+openwrt@de-korte.org>
2018-04-26 08:53:54 +02:00
Damir Samardzic
6f4faf833d mvebu: cortexa72: enable Marvell 10G PHY by default
This one enables 10 GbE ports on MACCHIATObin.

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
2018-04-25 20:37:22 +02:00
Mathias Kresin
91e11bec74 ramips: fix mt7628 eval board pinmux
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.

Fixes: FS#1515

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-25 20:33:27 +02:00
Mathias Kresin
d089a5d773 ramips: create image for mt7628 evb board
The image for the EVB board got lost with the merge of the mt7628 and
mt7688 subtargets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-23 22:07:22 +02:00
Tobias Wolf
3d800f14a9 ramips: use patch-dtb for F5D8235 V1
The old DTB method (OWRTDTB) is not recognized by the boot process
anymore with 4.9/4.14.

This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel
image.

Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
2018-04-23 22:07:22 +02:00
Giuseppe Lippolis
78666c7ba0 kernel: fix usb interface on 3G dwm-158 modem
The current option driver binds to the usb interface 2,3,4,5.
But the interface 4 and 5 doesn't answer to the AT commands.
On the new openwrt configuration the wwan script select the 5th
interface as control interface, failing to establish the
3G connection.

Backport the fix for the problem.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
0b20490207 ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
c6aac196b8 ipq40xx: fix gpio-hog related boot issues
The pinctrl initialization fails with the MSM pinctrl code and gpio-hogs
because either the gpio ranges are not yet initialized (missing gpio-range
in DT) or that the msm driver unconditionally tries to re-initializes the
ranges (gpio-range in DT).

To allow gpio-hogs and similar early-boot gpio code, the gpio-ranges must
be in the device tree and the pinctrl-msm code must check whether the range
was already initialized by the DT.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[drop changes to unrelated dtsi files, refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-23 22:07:22 +02:00
Sven Eckelmann
856f0d5d0d ipq40xx: use upstream board-2.bin
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-23 22:07:22 +02:00
Rafał Miłecki
b1f5dd34ed brcm47xx: backport upstream patches for Netgear WNR1000 V3
This includes fix for reading NVRAM content.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-04-23 13:33:09 +02:00
Thomas Hebb
16b25ad829 ipq40xx: ex61x0v2: Disable unused GMACs
These devices have only one ethernet port. It doesn't make sense to
expose the unused GMACs as separate network devices.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
2018-04-20 20:58:52 +02:00
Sven Eckelmann
c4c2a8f00c ipq40xx: Move reserved-memory DT to qcom-ipq4019.dtsi
The tz and smem reserved-memory information handled in the upstream Linux
sources by the SoC specific dtsi and not by the the boards dts. Using the
same approach in OpenWrt avoids unneccessary duplication.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-20 20:58:52 +02:00
Sven Eckelmann
0d62432834 ipq40xx: Remove unused reserved-memory nodes
The reserved-memory regions are mostly undocumented by QCA and are named
very unspecific in the QSDK device trees. It was tried to clean them up by
commit 71ed9f10a3 ("ipq40xx: Use detailed reserved memory for A42") and
similar changes.

The features which require these regions were mostly unknown but
Senthilkumar N L <snlakshm@qti.qualcomm.com> and Sricharan Ramabadhran
<srichara@qti.qualcomm.com> provided some more insight in some of them:

* crash dump feature
  - a couple of regions used when 'qca,scm_restart_reason' dt node has the
    value 'dload_status' not set to 1
    + apps_bl <0x87000000 0x400000>
    + sbl <0x87400000 0x100000>
    + cnss_debug <0x87400000 0x100000>
    + cpu_context_dump <0x87b00000 0x080000>
  - required driver not available in Linux
  - safe to remove
* QSEE app execution
  - region tz_apps <0x87b80000 0x280000>
  - required driver not available in Linux
  - safe to remove
* communication with TZ/QSEE
  - region smem <0x87b80000 0x280000>
  - driver changes not yet upstreamed
  - must not be removed because any access can crash kernel/program
* trustzone (QSEE) private memory
  - region tz <0x87e80000 0x180000>
  - must not be removed because any access can crash kernel/program

Removing the unnecessary regions saves some kilobyte of reserved-memory and
cleans up the device tree:

* 2560 KiB
  - 8devices Jalapeno
  - AVM FRITZ!Box 4040
  - Compex WPJ428
  - Meraki MR33 Access Point
  - OpenMesh A42
* 14336 KiB
  - GL.iNet GL-B1300
  - Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-04-20 20:58:52 +02:00
Mathias Kresin
74a0d8cd92 build: consolidate fake uImage header build commands
Merge the two existing functions and use a parameter for the type
header field.

It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-20 20:58:52 +02:00
Felix Fietkau
d89448fe43 mediatek: disable ubifs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-20 10:03:38 +02:00
Felix Fietkau
2fe0aaed7f mediatek: remove 4.9 kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-20 10:03:38 +02:00
Felix Fietkau
9ce5127a49 orion: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-19 14:38:57 +02:00
Felix Fietkau
decbecb0ad omap: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-04-19 14:38:53 +02:00