Align the LEDs deffinition with MACH file present in ar71xx target which
has the correct LED functions and colors adescription.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.
Specification
SoC: Qualcomm Atheros QCA9558
RAM: 256 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled
Buttons: 2x GPIO controlled
UART: 4 pin header, starting count from white triangle on PCB
1. VCC 3.3V, 2. GND, 3. TX, 4. RX
baud: 115200, parity: none, flow control: none
Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
is ready for configuration.
Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
then router ip (default is 192.168.99.9) and for last, image name
downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
You can observe progress on console, it'll take few minutes and when
the Power LED will stop blinking, router is ready for configuration.
Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.
Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
* Do not preserve settings
* Access rebooted device via Ethernet at OpenWrt default address
Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds
Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/
Runtime-tested: GL.iNet AR300M-Lite
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Hardware
--------
SOC: QCA9558
RAM: 128M DDR2
Flash: 16MiB SPI-NOR
ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN: 1x Reset
GPIO: multiple GPIO on header, PoE passthrough enable
UART: 3.3V 115200 8N1 header on the board
WDG: ATTiny13 watchdog
JTAG: header on the board
USB: 1x connector and 1x header on the board
PoE: 10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)
OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.
Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
ath> tftp 82000000 <your image>-sysupgrade.bin
ath> erase 0x9f050000 +$filesize
ath> cp.b 0x82000000 0x9f050000 $filesize
ath> bootm 0x9f050000
More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.
Specification:
- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB
Flash instruction:
1. First, gain root access to the device, following below steps:
- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.
2. Then, install OpenWrt:
- Login over SSH and issue command:
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
succeeded) with command: 'sysupgrade -n -F openwrt-...'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN: 2.4/5 GHz
UART: 1 UART
LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This allows resetting gmac registers during initialization.
Also add compatible string for qca955x mdio to enable more mdio
clock dividers.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit makes the TP-Link hardware-revision naming consistent to
match the one used by the vendor. TP-Link refers to the different
revisions as "vX" not "Version X".
Signed-off-by: David Bauer <mail@david-bauer.net>
Commit 34b10b46 made usb match with the corresponding usb label.
The problem is that v4 seems to use in stock firmware the
upper led for usb 1 and the lower led for usb 2.
The led assigned varies between TP-Link models and even
same model versions. For example, Archer C7 v1 and v2 have
the leds in the reverse order.
Revert 34b10b46 and swap led labels instead, now usb port
and led label match and also respect the original behavior.
Tested-by: Oldrich Jedlicka <oldium.pro@gmail.com>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
In the production of glinet, the MAC address of ethernet port is
only written at the position where the ART area offset address
is 0, and the MAC address of eth1 is added 1 on the basis of eth0.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
According to /arch/mips/include/asm/mach-ath79/ar71xx_regs.h
the size of wmac register range for qca953x is only 0x20000.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.
Specification:
- SoC: Qualcomm Atheros QCA9557
- RAM: 128 MB
- Flash: 16 MB
- WLAN: 2.4/5 GHz
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
- Switch: QCA8337N
- LED/key: 6x/6x(4x buttons, 1x slide switch)
- UART: through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Alternative flash instruction using initramfs image:
1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing
This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested with a dual pci QCA9558 board (LibreRouter v1) in three
configurations: enabling pcie0 only, pcie1 only and both enabled.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
Datasheet states that both PCI ranges are of 0x2000000 size:
0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
Hardware
--------
CPU: Qualcomm Atheros QCA9561
RAM: 64M DDR2
FLASH: 16M SPI-NOR
ETH: 1x WAN - 2x LAN
WiFi: QCA9561 3T3R
BTN: 1x Reset - 1x WPS
LED: 1x Blue - 1x Red - 1x Yellow
UART: TX - GND - RX - VCC (From ethernet port)
115200n8 - 3.3V
Installation
------------
1. Connect to the device via UART.
2. Interrupt the U-Boot on power-on by pressing enter when prompted.
3. Connect you computer to one of the routers LAN ports.
Assign yourself the IP 192.168.31.10/24.
Copy the OpenWRT initramfs image to a tftp server root directory.
Rename the image to 'x4q.bin'.
4. Load the initramfs image to the router by executing following command
in U-Boot. The image will boot afterwards.
> tftpboot 0x81000000 x4q.bin; bootm
5. SCP the sysupgrade-image into '/tmp'.
Remember to assign yourself an IP in 192.168.1.0/24 for this step!
6. Install OpenWRT permanently by executing
> sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>
Signed-off-by: David Bauer <mail@david-bauer.net>
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN: 1x Reset
1x WPS
1x USB eject
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
Dupont 4 pin header
Rear RJ45 serial port non-functional
USB: 1x v2.0
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
Change the "status" LED to proper GPIO 12 and "red" naming.
Remove GPIO 2 from definition as a USB LED.
GPIO 2 is used to control power to the USB socket, not an LED.
As such, PWM on the line or typical LED triggers are inappropriate.
Users who wish to control the USB power for custom applications
can manipulate the GPIO through code, or for example, export it
through /sys/class/gpio/export.
Runtime-tested: GL.iNet AR300M-Lite
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
The 'factory' partition will move to 0x50000-0x60000 in 2019. As
the webserver in bootloader is compatible with different mtdlayout,
all the users still can upgrade firmware whatever on ath79 or ar71xx.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.
Specifications:
- 650/400/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 26 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new want, so a factory reset will be
needed: once the new firmware is flashed, perform the factory reset by
pushing the reset button several times during the boot process, while the
WAN LED flashes, until it starts flashing quicker.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and keep it
pressed for >10 seconds. The recovery page will be at http://192.168.1.1
Notes:
The device is advertised, sold and labeled as "CF-E110N", but the
bootloader and the stock firmware identify it as "v2".
Acknowledgments:
Petr Štetiar <ynezz@true.cz>
Sebastian Kemper <sebastian_ml@gmx.net>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for TP-Link Archer C6 v2 (EU)
Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board
Flash instructions:
Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.
Short specification:
- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
(ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
(ath)> erase 0x9f060000 +f50000
(ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
(ath)> reset
Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.
Furtheremore support for the MicroSD port is not implemented as of now.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
- Another LED can be accessed on GPIO 7 if soldered
Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The OCEDO Koala has incorrect PLL settings which result in ~3% packet
loss on ethernet connections.
Also omit the gmac-configuration as it's incorrect too.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880
USB is supported on the PCB but not connected.
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or the u-boot
failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted. Otherwise the u-boot
will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the firmware
checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
upgrade the factory.bin through the u-boot failsafe interface and then goto
step 2.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
It's same for Bullet and Nanostation so far, so let's hope it's going to
be the same for other boards sharing the same platform.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It's not necessary as it's already defined in ar934x.dtsi to:
pll-data = <0x16000000 0x00000101 0x00001616>;
And in ar71xx it's currently set to the same values:
#define AR934X_PLL_VAL_1000 0x16000000
#define AR934X_PLL_VAL_100 0x00000101
#define AR934X_PLL_VAL_10 0x00001616
And dumping the value from the airOS v6.1.7 has the same value:
AR934X_PLL_ETH_XMII_CONTROL_REG 0x1805002C 0x101
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently there is no LED signalization for various system states
implemented in diag.sh, so this patch adds support for it.
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).
It is also not mentioned in the devolo manual.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.
Specification:
- QCA9563 SoC (750 MHz)
- 128 MiB of RAM (DDR2)
- 16 MiB of flash (SPI)
- 5x 1 Gbps Ethernet (1x WAN + 4x LAN)
- 2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
- 10x LED, 2x button
- UART header on PCB
Flash instructions:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
via web interface.
Flash instructions using TFTP recovery:
1. Plug PC to one of the LAN ports
2. Set PC to fixed IP address 192.168.0.66
3. Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
TFTP root directory
4. Turn on the router with the reset button pressed for about 15 secs
5. Release the button and wait about 150 secs to complete flashing
Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
The range of pinmux reg property "<0x1804002c 0x40>" for QCA955x
SoC does not includes GPIO_FUNCTION register.
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.
Specification:
- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
- 2.4 GHz: 2T2R (SoC internal)
- 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
- Vcc, GND, NC, TX, RX from SoC side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The range of pinmux reg property "<0x1804002c 0x40>" for QCA956x SoC
does not includes GPIO_FUNCTION register.
If the device uses "&jtag_disable_pins", this causes the following
errors:
[ 1.982937] pinctrl-single 1804002c.pinmux: mux offset out of range: 0x40 (0x40)
[ 1.990622] pinctrl-single 1804002c.pinmux: could not add functions for pinmux_jtag_disable_pins 64x
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for TP-Link Archer A7
Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) SoC internal
- 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
- Vcc, GND, RX, TX from ethernet port side
- 115200n8
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing
Changes since first revision:
- Flash instructions using stock image webinterface
- Changed "Version 5" in model string to "v5"
- Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
and qca9563_tplink_archer-a7-v5.dts
- Firmware image is now build with dynamic partitioning
- Default to ath10k-ct
Changes since second revision:
- Changed uboot@0 to uboot@20000 in DTS file
- Fixed ordering issue in board led script
- Specify firmware partition format in DTS file
- Rebased Makefile device definition on common
Device/tplink-safeloader-uimage definition
- Merged switch section in network script
(same configuration as tplink,tl-wdr3600
and tplink,tl-wdr4300)
Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
This patch fixes wrong usage of debounce-interval subnode property of
gpio-keys-polled nodes, which was used inproperly in parent node, but it
belongs to the subnodes, excerpt from the docs:
Optional subnode-properties:
- debounce-interval: Debouncing interval time in milliseconds.
If not specified defaults to 5.
And the docs are up to date as the source code matches that description
as well:
if (fwnode_property_read_u32(child, "debounce-interval",
&button->debounce_interval))
button->debounce_interval = 5;
While at it, I've also re-formatted gpio-keys-polled nodes, usually just
adding new lines after every key subnode.
Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Cc: Matt Merhar <mattmerhar@protonmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.
The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.
https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1
Installation:
1. Connect to the web interface of the vendor firmware (usually
listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.
Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.
CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS
AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
The qca9557/qca956x reset-controller aren't a simple bus. A simple bus
would require node unit addresses.
Add the node unit addresses for the qca9557 usb phys. Add the regs for
the USB_PWRCTL and USB_CONFIG registers even not yet used.
Fix the wrong ar7100 pcie controller node unit address as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files /
base files support using both colours to better inform user of state
and to better match stock firmware, so use green power to indicate
normal operation.
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.
WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.
There is no eeprom data for 5 GHz wlan in "art" partition.
Specification:
- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
- 2.4 GHz: SoC internal
- 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.
Specification:
- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338
Known issue:
5G ath9k led doesn't work due to commit ccab68f.
Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.50
3. Load and flash the firmware:
tftp 0x80060000 fw.bin
erase 0x9f050000 +$filesize
cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
reset
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>
merge
This commit fixes several issues in eth0 on ETG3-R, and solve slowdown
in NA(P)T speed.
- add gmac-config with correct configurations
- fix pll-data value
And I added ref clock-frequency.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The userspace boardname derived from the dts compatible was out of sync
with the expected board added to the image metadata. This way a
sysupgrade is refused.
Sync the userspace boardname and the baordname used in the image metdata
to allow a seamless sasupgrade.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds firmware partition compatible for the
AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E.
This allows to select the correct mtdsplit parser
instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
Parsing "firmware" partition (to create kernel + rootfs) was implemented
using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With
recent upstream mtd changes we can do it in a more clean way for DTS
targets. It just requires adding a proper "compatible" string to the
"firmware" partition node.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE.
Rename the misleading dtsi names and fix the SoC type of gl-ar300m.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[apply the changes for the gl-x750 as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Indoor low-power router with 2.4 GHz radio
CPU: Atheros AR7241 rev 1
RAM: 32 MB
Flash: 8 MB NOR SPI
Switch: Atheros AR7240
Ports: 1x WAN, 4x LAN 10/100 Ethernet
WLAN: Atheros AR9285 (2.4 GHz)
USB: 1x USB2 host port
Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.
UART settings: 115200, 8N1
LEDs
+--------------------------
|
|
|
|
|
|
|
|
VCC | x x
RX | * x
| x x
| x x
TX | * x
GND | * x
|
|
|
|
+--------------------------
ETHERNET PORTS
Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Having MIT as alternative is sometimes preferred by upstream maintainers
and allows sharing that simple code with other projects. We don't really
want multiple DTS versions for the same device.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
The board doesn't come in different flash type flavours, hence there is
no need to keep a dtsi + dts for this purpose.
While at it, fix some whitespace issues.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This commit adds firmware partition compatible for the
TP-Link Archer C58 v1 and Archer C59 v1.
Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds firmware partition compatible for the
OCEDO Raccoon and OCEDO Koala.
Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.
Signed-off-by: David Bauer <mail@david-bauer.net>
Specify firmware partition format (denx,uimage) by compatible string
for ELECOM WRC-300GHBK2-I.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.
CPU: Qualcomm QCA9561
RAM: 64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi: QCA9561 bgn 3x3:3
QCA9888 nac 2x2:2
LED: Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
Only C59: USB
BTN: WPS, WiFi, Reset
Installation
------------
Via Web-UI:
Update factory image via Web-UI.
Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.
Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.
Signed-off-by: David Bauer <mail@david-bauer.net>
this patch adds supports for GL-X750.
Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)
Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions
A) Serial console, U-Boot and TFTP
1. Connect to serial header J1 on the PCB
2. Power on device and enter U-Boot console
3. Set up TFTP server serving an OpenWrt initramfs build
4. Load initramfs build using the command tftpboot in the U-Boot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs OpenWrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
B) Experimental factory image flashing over SSH from airOS v6.1.7
1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
no other airOS version is currently supported
2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
3. cd ubnt-bullet-m2hp-openwrt-flashing
4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specify the new "firmware" partition format for Netgear WNDR3700
and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third
device in the family.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Ports: 1 GbE port (PoE in)
WLAN: 5 GHz QCA899X (PCI)
The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).
Installation procedure is the same as the NanoStation [loco] AC:
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This commit adds support for the TP-Link TL-WR901ND v2 access point.
CPU: Atheros AR9132 400MHz
RAM: 32MB
FLASH: 4MiB
WiFi: Atheros AR9103 3x3:2 bgn
LED: Power (static on)
LAN (controlled by PHY)
SYS, WiFi, QSS toggleable
BTN: Reset, QSS
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: David Bauer <mail@david-bauer.net>
Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros
AR7242.
It is Japanese market model of WZR-HP-G300NH2, but there are some
diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx.
And, G302H has several hardware versions and hardware is different
dependent on the versions. This commit adds support for "A1A0"
version.
Specification:
- Atheros AR7242
- 64 MB of RAM (DDR2)
- 32 MB of Flash
- 2x 16 MB SPI-NOR flash
- 2.4 GHz 2T2R wifi
- Atheros AR9283
- 5x 10/100/1000 Mbps Ethernet
- Atheros AR8316
- 7x LEDs, 5x keys
- LED: 1x gpio-leds, 6x ath9k-leds
- key: 3x buttons, 2x slide switches
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- 115200n8
Flash instruction using factory image:
1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port
2. Access to "http://192.168.11.1/" and move to firmware update page
("ファーム更新")
3. Select the OpenWrt factory image and click update ("更新実行")
button to perform firmware update
4. Wait ~200 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79.
This is a low cost model with following specs:
CPU: Atheros AR9341 SoC
RAM: 32 MB DDR1
Flash: 8 MB NOR SPI
Switch: Internal AR9341 5 port 10/100 Mbit
Ports: 5x 10/100 Mbit(1x WAN, 4x LAN)
USB: 1x USB2.0
WLAN: 2.4 GHZ AR9341
Installation:
Simply flash the factory image through stock firmware WEB UI.
Signed-off-by: Robert Marko <robimarko@gmail.com>
5 GHz AC wireless outdoor PoE CPE with internal 2.4 GHz management radio
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Switch: QCA8334
Ports: 2 GbE ports (1x PoE in, 1x PoE passthrough)
WLAN: 5 GHz QCA899X (PCI) and 2.4 GHZ AR9342
Successor to the old NanoStation M5 with AC wireless.
The integrated QCA899X is a Ubiquiti branded part with modified vendor and
product id (0777:11ac9).
Serial
Serial settings: 115200, 8N1
* = plated through hole
0 = nylon screw
[Top of device]
+--------------------------+
| [label] |
| 0 |
| 0 |
| [ubnt] |
| [logo] 3V3 * |
| TX * |
| RX * |
| GND * |
| |
| * |
| * |
| * |
| * |
| 0 |
| 0 |
| |
| |
Installation
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
Atheros AR9342, 16 MB flash, 64 MB RAM
Successor to the old NanoStation M5 loco with AC wireless.
Includes a mac80211 patch for ath10k_pci because Ubiquiti uses a Ubiquiti
branded and customized QCA988X with vendor id 0777 and device id 11ac for
AC wireless.
Installation
1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
