Commit Graph

241 Commits

Author SHA1 Message Date
Jackson Lim
209b368254 ath79: add support for D-Link DIR-842 C2
Hardware spec of DIR-842 C2:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: 2.0

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[Reword reset-hog comment, fix formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-24 11:36:02 +02:00
INAGAKI Hiroshi
d616b2c906 ath79: modify device name of I-O DATA WN-AC1600DGR2
The hardware of I-O DATA WN-AC1600DGR3 has completely compatibility
with WN-AC1600DGR2, so modify the device name of WN-AC1600DGR2 to show
the images for DGR2 also support DGR3.

Specification of WN-AC1600DGR3:

- SoC        : Qualcomm Atheros QCA9557
- RAM        : DDR2 128 MiB
- Flash      : SPI-NOR 16 MiB
- WLAN       : 2.4/5 GHz
  - 2.4 GHz  : QCA9557 (SoC), 2T2R
  - 5 Ghz    : QCA9880, 3T3R
- Ethernet   : 5x 10/100/1000 Mbps
  - Switch   : QCA8337N
- LEDs/Input : 6x/6x (4x buttons, 1x slide-switch)
- UART       : through-hole on PCB
  - J1: Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-18 00:06:55 +02:00
Adrian Schmutzler
974d6958a7 ath79: Add support for TP-Link Archer C60 v2
TP-Link Archer C60 v2 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

Flash instruction (under U-Boot, using UART):
tftp 0x81000000 ...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-18 00:06:55 +02:00
Adrian Schmutzler
6d313da6dc ath79: Add support for TP-Link Archer C60 v1
TP-Link Archer C60v1 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 ...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-18 00:06:55 +02:00
Andrew Cameron
cad4132e00 ath79: add support for TP-Link CPE510-v2/v3
TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - Based on the same underlying hardware as the TP-Link CPE510
 - Power, LAN, and 4 green LEDs
 - 1 10/100Mbps Shielded Ethernet Port (Passive PoE in)
 - Built-in 13dBi 2x2 dual-polarized directional MIMO antenna
 - Adjustable transmission power from 0 to 23dBm/200mw

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-18 00:06:55 +02:00
Pramod Pancha
8e384ba830 ath79: add support for Trendnet TEW-823DRU
Trendnet TEW-823DRU is a dual-band AC1750 router.
The router is based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

720 MHz CPU
256 MB of RAM
16 MB of FLASH
3T3R 2.4 GHz
3T3R 5 GHz
5x 10/100/1000 Mbps Ethernet

Firmware can be flashed from the web interface. Tested on 3 routers
with no issues.

Signed-off-by: Pramod Pancha <pancha@vill.com>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-18 00:06:55 +02:00
Christoph Krapp
6fde0b735c ath79: add support for TP-Link RE355 v1 and RE450 v1
Specification:

SoC: Qualcomm Atheros QCA9558
RAM: 64/128MiB
Flash: 8MiB SPI-NOR
Wifi:
  - 2.4GHz: 3T3R (QCA9558)
  - 5GHz: 3T3R (QCA9880)
LAN: 1x 10/100/1000 Mbps
UART:
  - TP1: Tx
  - TP2: Rx
  - TP3: Gnd
  - TP4: 3v3

Flash instructions:
Flash factory image through stock firmware WEB UI.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-07-17 23:14:23 +02:00
Daniel Gimpelevich
bc18c2bfe7 ath79: add support for Bluesocket BSAP1880 board
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.

Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B

Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
   115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
   file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
   load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80060000 -l LeNgTh vmlinux_2
   load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
   use a hexadecimal calculator to subtract the start from the end in order
   to substitute it below, with the leading "0x" to specify it in
   hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
   reset
10.Wait for the status LED to go solid green

Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-17 22:59:29 +02:00
Chuanhong Guo
a9360452f0 ath79: add support for Qihoo C301
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882

Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-16 09:51:03 +08:00
David Bauer
cb3cd52694 ath79: add support for devolo WiFi pro 1750x
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED Power (non-controllable)
       1x LED Status (internal)
       1x LED LAN (controlled by PHY)
       1x LED WLAN
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to external-LED header.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-14 16:20:53 +02:00
Chen Minqiang
dcb5cf85c8 ath79: fix missing DEVICE_VENDOR for some devices
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2019-07-10 17:16:49 +02:00
Adrian Schmutzler
301a78d1d5 ath79: Add missing IMAGE_SIZE for Etactica EG200
The Etactica EG200 is the only device in ath79 despite nand
target that lacks IMAGE_SIZE.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-08 16:28:47 +02:00
Andrew Cameron
d5a38725f8 ath79: increase kernel partition size for CPE610v1
Increase the Kernel partition to address the issue discussed here
https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5
Switch Back to the okli Loader to support increased partition size

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
2019-07-07 13:02:06 +02:00
Adrian Schmutzler
63e3c3d2a2 ath79: Add DEVICE_VENDOR for Ubiquiti Routerstation
This has been overlooked.

Reported by: Chen Minqiang (@ptpt52)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-05 19:08:46 +02:00
Adrian Schmutzler
b1100fc586 ath79: Correctly use DEVICE_VARIANT for NETGEAR WNDR3700
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-04 18:17:52 +02:00
Adrian Schmutzler
5bba6b4e6b ath79: Move DEVICE_VENDOR for NETGEAR to parent definition
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-04 18:17:52 +02:00
Paul Spooren
8c3dbaf8b4 ath79: split DEVICE_TITLE in multiple variables
This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and
DEVICE_VARIANT. All three are merged together to look the same as the
current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as
a *fallback* for devices which weren't upgraded yet.

This is based on the work of @sudhanshu16.

The motivation is to create JSON files based on provided metadata,
needing clear differentiation between vendor, model and revision.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-07-04 15:50:17 +02:00
Adrian Schmutzler
ab02584685 ath79: Use -v1 suffix for TP-Link WDR3600/4300
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.

Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.

This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-03 07:45:00 +02:00
Andrew Cameron
e15049c88b ath79: add support for TP-Link CPE610-v1
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - Based on the same underlying hardware as the TP-Link CPE510
 - Power, LAN, WLAN5G green LEDs
 - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector

Flashing instructions:
 Flash factory image through stock firmware WEB UI
 or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2019-06-24 20:22:24 +02:00
Adrian Schmutzler
2b3545720b ath79: Add SUPPORTED_DEVICES for Archer C7 v1/v2
The identifier for both devices is "archer-c7" on ar71xx, set here:
https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L348
https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L511

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-15 20:03:32 +02:00
Adrian Schmutzler
fde0abf267 ath79: Add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:47 +02:00
Rytis Zigmantavičius
64493d42b4 ath79: add support for 8devices Carambola2 development board
Specifications:
- Atheros AR9331 (400 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of Flash (SPI)
- 1T1R 2.4 Wlan (AR9331)
- 2x 10/100 Mbps Ethernet
- 3x LEDs, 1x gpio button
- 1x USB 2.0, 5V
- UART over usb, 115200n8

Upgrading from ar71xx target:
- Put image into board:
    scp openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin \
        root@192.168.1.1/tmp/
- Run sysupgrade
    sysupgrade /tmp/sysupgrade.bin

Upgrading from u-boot:
- Set up tftp server with sysupgrade.bin image
- Go to u-boot (reboot and press ESC when prompted)
- Set TFTP server IP
    setenv serverip 192.168.1.254
- Set device ip from same subnet
    setenv ipaddr 192.168.1.1
- Copy new firmware to board
    tftpboot 0x81000000 sysupgrade.bin
- erase flash
    erase 0x9f050000 +${filesize}
- flash firmware
    cp.b 0x81000000 0x9f050000 ${filesize}
- Reset board
    reset

Signed-off-by: Rytis Zigmantavičius <rytis.z@8devices.com>
[wrapped long line in commit description, whitespace and art address
 fix in DTS, keep default lan/wan setup, removed -n in sysupgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:24:45 +02:00
Kristian Evensen
046263095e ath79: Add support for ZBT-WD323
ZBT-WD323 is a dual-LTE router based on AR9344. The detailed
specifications are:

* AR9344 560MHz/450MHz/225MHz (CPU/DDR/AHN).
* 128 MB RAM
* 16MB of flash(SPI-NOR, 22MHz)
* 1x 2.4GHz wifi (Atheros AR9340)
* 3x 10/100Mbos Ethernet (AR8229)
* 1x USB2.0 port
* 2x miniPCIe-slots (USB2.0 only)
* 2x SIM slots (standard size)
* 4x LEDs (1 gpio controlled)
* 1x reset button
* 1x 10 pin terminal block (RS232, RS485, 4x GPIO)
* 2x CP210x UART bridge controllers (used for RS232 and RS485)
* 1x 2 pin 5mm industrial interface (input voltage 12V~36V)
* 1x DC jack
* 1x RTC (PCF8563)

Tested:
- Ethernet switch
- Wifi
- USB port
- MiniPCIe-slots (+ SIM slots)
- Sysupgrade
- Reset button
- RS232

Intallation and recovery:

The board ships with OpenWRT, but sysupgrade does not work as a
different firmware format than what is expected is generated.  The
easiest way to install (and recover) the router, is to use the
web-interface provided by the bootloader (Breed).

While the interface is in Chinese, it is easy to use. First, in order to
access the interface, you need to hold down the reset button for around
five seconds. Then, go to 192.168.1.1 in your browser. Click on the
second item in the list on the left to access the recovery page. The
second item on the next page is where you select the firmware.  Select
the menu item containing "Atheros SDK" and "16MB" in the dropdown close
to the buttom, and click on the button at the bottom to start
installation/recovery.

Notes:
* RS232 is available on /dev/ttyUSB0 and RS485 on /dev/ttyUSB1

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[removed unused poll-interval from gpio-keys, i2c-gpio 4.19 compat]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-05 10:24:36 +02:00
Ryan Mounce
6d6985ff0e ath79: add support for WD My Net N750
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n

5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO

Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.

UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX

See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.

Tested sysupgrade + factory flash from WD Emergency Recovery

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2019-05-27 22:44:08 +02:00
Alexander Wördekemper
0f6b944c92 ath79: glinet_gl-ar750s: Add USB power & microSD
The GL.iNet AR750S USB and microSD port is currently not working out of
the box.  GPIO 7 is used to control the power of the USB port. Add GPIO
7 as a fixed-regulator for the port.  Also add &usb1 to DTS to get the
microSD port to work.

Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
2019-05-20 21:25:00 +02:00
Davide Fioravanti
f5d2c91415 ath79: add support for TP-Link Archer D50 V1
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.

Internally eth0 is connected to the Broadcom CPU.

Router section - Specification:

CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB

Known issues:
DSL not working (eth0) (WIP)

UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC

J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX

The following instructions require a connection to the J2 UART header.

Flash instruction under U-Boot, using UART
------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +$filesize
	cp.b 0x81000000 0x9f020000 $filesize
	reset

Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
	bootm 0x81000000

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
 4. Double check the .mod file size. It must be 7995392 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
        tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
        erase 0x9f020000 +$filesize
        cp.b 0x81000000 0x9f020000 $filesize
        reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
2019-05-18 17:59:49 +02:00
Chris Blake
aee5c98619 ath79: add support for Aruba AP-105
SoC: Atheros AR7161-8C1A @ 680 MHz
RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G
NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR)
WI1: Atheros AR9223-AC1A 802.11bgn
WI2: Atheros AR9220-AC1A 802.11an
ETH: Atheros AR8021-BL1E + PoE
LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G
BTN: 1 x Reset
I2C: AT97SC4303s TPM (needs driver!)
CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud

Factory installation:

 - Needs a u-boot replacement. See Wiki for
   information on how to do a in-circut flash with
   a SPI-Flasher like a CH314A or flashrom. Wiki page
   can be found at https://openwrt.org/toh/aruba/aruba_ap-105

 - Be careful when dis- and reassembling the device to
   not squish any of the antenna cables in the process!

 - Be sure to make a full 16 MiB backup of your device
   before flashing the new u-boot! This is needed if you
   ever have interest in reverting back to stock firmware.

Not working:

 - TPM (needs a driver)

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2019-05-18 16:44:41 +02:00
Adrian Schmutzler
d4b89b7170 ath79: Add support for TP-Link TL-WR1043N v5
Specifications:

 - QCA9563 at 775 MHz
 - 64 MB RAM Zentel A3R12E40CBF-8E
 - 16 MB flash Winbond W25Q128FVSG
 - 3 (non-detachable) Antennas / 450 Mbit
 - 1x/4x WAN/LAN Gbps Ethernet (QCA8337)
 - reset and Wi-Fi buttons

TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4,
except that the USB port has been removed and there is no longer a
removable antenna option. It also has different partitioning scheme.

The software is more in line with the Archer series in that it uses a
nested bootloader scheme.

(This has been adapted from the OpenWrt Wiki page)
<https://openwrt.org/toh/tp-link/tl-wr1043nd>

Installation on HW rev.5:

Factory firmware can be installed via the WEB interface.

Alternatively, it is also possible to use a TFTP server
for recovery purposes:
 - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin
 - Set static IP of your PC to *192.168.0.66*
 - Router will obtain IP 192.168.0.86 for a few seconds while
   loading, when reset button pressed at power On.

And finally, there's always u-boot access through the UART.
For information visit the wiki.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message]
2019-05-18 16:38:18 +02:00
Adrian Schmutzler
78ea648a3a ath79: Move TL-WR1043ND v1 definition to companions
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-05-18 16:38:18 +02:00
sven friedmann
30dcbc741d ath79: add support for EnGenius ECB1750
Specification:

- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)

https://fccid.io/A8J-ECB1750

Tested and working:

- lan, wireless, leds, sysupgrade (tftp)

Flash instructions:

1.) tftp recovery

- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade

2.) oem webinterface factory install (not tested)

Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".

3.) oem webinterface command injection

OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.

https://openwrt.org/toh/engenius/engenius_ecb1750_1

Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
2019-05-18 13:43:55 +02:00
Jeff Kletsky
2437418cd5 ath79: glinet_gl-ar750s: Use QCA9887 firmware
The GL.iNet AR750S is based around the QCA9563
and requires the QCA9887 firmware for operation.

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-05-05 21:11:01 +02:00
INAGAKI Hiroshi
3fd443640c ath79: remove unnecessary packages from I-O DATA ETG3-R
I-O DATA ETG3-R is a wired router. So wireless-related packages are
unnecessary and remove those packages from default configuration to
reduce flash usage.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-04-13 15:06:36 +02:00
Sven Roederer
e0d98e120a ath79: add TP-Link WR842N v3
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).

Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)

Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)

Thanks to Holger Drefs for providing the hardware

Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2019-04-13 14:39:59 +02:00
Daniel Gimpelevich
f61e754522 ath79: add support for Netgear EX6400 and EX7300
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.

Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A

Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Daniel Gimpelevich
d75d4837fc ath79: remove more duplicate image build variables
Remove Netgear-specific image build variables which are set to the same
value.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[reordering of variables, removed stray newline]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Christian Mauderer
8a4dc6f48c ath79: add support for Ubiquiti airCube ISP
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.

SoC:       Qualcomm / Atheros QCA9533-BL3A
RAM:       64 MB DDR2
Flash:     16 MB SPI NOR
Ethernet:  4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS:      1x via a SPI controller (not yet supported)
Buttons:   1x Reset
Serial:    1x (only RX and TX); 115200 baud, 8N1

Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
  (Needs RSA signed images, for details see PR#1958)

The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND

Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
  key to stop autoboot` is displayed. Note: Pressing space multiple
  times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
  running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
  image to the server.
- Set the U-Boot server IP with
    setenv serverip 192.168.1.100
- Load the flash image to RAM with
    tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
    erase 0x9f050000 0x9ffaffff
- Write the new flash content with
    cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
    reset

Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Markus Scheck
de2f888024 ath79: add support for OCEDO Ursus
SOC:   Qualcomm Atheros QCA9558
RAM:   128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED:   Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
       Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
       The Serial setting is 115200-8-N-1

INSTALLATION:

1. Serve an OpenWrt ramdisk image named "ursus.bin".
   Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
   the boot process.
3. Set the correct bootcmd with
   > setenv bootcmd run bootcmd_1
   > saveenv
4. Run
   > tftpboot 0x81000000 ursus.bin
   > bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.

Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
INAGAKI Hiroshi
643fcfc8d6 ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
2019-04-06 19:14:06 +02:00
Adrian Schmutzler
0eef05fb36 ath79: Utilize tplink-safeloader definition
Currently, tplink-safeloader definition is only used a base for
another common definition.

This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.

This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
2019-04-06 19:14:06 +02:00
Adrian Schmutzler
141698ce8f ath79: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-02 02:10:59 +02:00
Mario Schroen
5ec205d7ac ath79: Add support for TP-Link CPE210 v3
Specifications:

    * SoC: Qualcomm Atheros QCA9533 (650MHz)
    * RAM: 64MB
    * Storage: 8 MB SPI NOR
    * Wireless: 2.4GHz N based built into SoC 2x2
    * Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
    Flash factory image through stock firmware WEB UI or TFTP
    To get to TFTP recovery just hold reset button while powering
    on for around 4-5 seconds and release.
    Rename factory image to recovery.bin
    Stock TFTP server IP:192.168.0.100
    Stock device TFTP adress:192.168.0.254

Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.

Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-02 02:10:59 +02:00
Ding Tengfei
acf149d531 ath79: add support for COMFAST CF-E5/E7
COMFAST CF-E5/E7 is a outdoor 4G LTE AP with PoE support, based on
Qualcomm/Atheros QCA9531.

Short specification:

    2x 10/100 Mbps Ethernet, with 24v PoE support
    64 MB of RAM (DDR2)
    16 MB of FLASH (SPI)
    2T2R 2.4 GHz, 802.11b/g/n
    built-in 1x 3 dBi antennas
    output power (max): 80 mW (19 dBm)
    Qucetel EC20 LTE MODULE(1x external detachable antenna)

Flash instruction:

Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

Signed-off-by: Ding Tengfei <dtf@comfast.cn>
[commit subject fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:27 +01:00
Marcin Jurkowski
fcc716e21d ath79: add TP-Link TL-WR710N v1
This commit adds support for TP-Link TL-WR710N v1 router.

CPU: Atheros AR9331 400MHz
RAM: 32MB
FLASH: 8MiB
PORTS: 1 Port 100/10 LAN (connected to a switch), 1 Port 100/10 WAN
WiFi: Atheros AR9331 1x2:1 bgn
USB: ChipIdea HDRC USB2.0
LED: SYS
BTN: Reset

Sysupgrade from `ar71xx` works without glitches.
Network interfaces assigned for LAN and WAN ports are `eth1` and `eth0`
respectively, what's consistent with `ar71xx` target. Wireless radio
path is automatically upgraded from `platform/ar933x_wmac` to
`platform/ahb/18100000.wmac`.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
2019-03-24 01:44:27 +01:00
Chuanhong Guo
8de907c441 ath79: add support for TP-Link TL-WR941N v7 (CN)
This adds support for the Chinese version of TL-WR941N v7.
It uses QCA9558+AR8236 while the international version
uses TP9343 instead.

Specification:
- SoC: Qualcomm Atheros QCA9558
- Flash: 4 MB
- RAM: 64 MB
- Ethernet: Atheros AR8236 with 5 FE ports

Flash instruction:
  Upload the generated factory firmware on web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-03-24 01:44:27 +01:00
Tobias Schramm
d78e229903 ath79: Add support for Ubiquiti NanoBeam AC
The NanoBeam is a small AR9342 based directional 5 GHz AC CPE with hardware
almost identical to the Ubiquiti NanoStation AC loco. Over the NanoStation
AC loco it has 5 additional LEDs. Four of those LEDs are used as rssi
indicators, the fifth LED is used as an ethernet link/activity indicator.

CPU:   Atheros AR9342 SoC
RAM:   64 MB DDR2
Flash: 16 MB NOR SPI
WLAN:  QCA988X
Ports: 1x GbE

Flashing procedure is identical to the NanoStation AC loco and can be performed
either via serial or the factory firmware upgrade.

Serial flashing:

1. Connect to serial header on device (8N1 115200)
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Flashing through factory firmware:

1. Ensure firmware version v8.5.0.36727 is installed. Up/downgrade to this exact version.
2. Patch fwupdate.real binary using `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe fe/00 00 00 00/g' | hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using `chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWRT using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot

Thanks to @cybermaus for testing!

Tested-by: Maurits van Dueren den Hollander <cybermaus@gmail.com>
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
2019-03-22 00:40:29 +01:00
Sven Roederer
f1396ac753 ath79: align naming of Ubiquiti Nanostation M
Support for the Nanostation M (XW) was added in 40530c8eb with board
name "nanostation-m-xw". The current image for the "Nanostation M"
uses "nano-m" as the board name.
This commit renames it to the full product name as it's used by all
other boards. The legacy boardname of the ar71xx target is added
via SUPPORTED_DEVICES to ease switching to ath79 target.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[touch-ups on the commit message, removed subject remains]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-18 20:55:24 +01:00
Tomasz Maciej Nowak
b3a0c97b8c ath79: add support for jjPlus JA76PF2
jjPlus JA76PF2 (marketed as IntellusPro2) is a network embedded board.

Specification
SoC:		Atheros AR7161
RAM:		64 MB DDR
Flash:		16 MB SPI NOR
Ethernet:	2x 10/100/1000 Mbps AR8316
		LAN (CN11), WAN/PoE (CN6 - close to power barrel
		connector, 48 V)
MiniPCI:	2x
LEDS:		4x, which 3 are GPIO controlled
Buttons:	2x GPIO controlled
		Reset (SW1, closer to ethernet ports), WPS (SW2)
Serial:		1x (only RX and TX are wired)
		baud: 115200, parity: none, flow control: none

Currently there is one caveat compared to ar71xx target images as the
MAC addresses are random on every reboot. To remedy this one needs to
store the WAN MAC address in RedBoot configuration. OpenWrt on first
boot, after flashing, will read out the address and assign proper ones
to both WAN and LAN ports. It is iportant to NOT keep the old
configuration when doing sysupgrade from ar71xx.

Upgrading from OpenWrt ar71xx image
1. Connect to serial port,
2. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n <openwrt_sysupgrade_image_name>
3. After writing new image OpenWrt will reboot, now interrupt boot
   process and enter RedBoot (bootloader) command line by pressing
   Ctrl+C,
4. Enter following commands (replace variable accordingly),
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_adress>
    (confirm storing the value by inputting y and pressing Enter)
    reset
5. Now board should restart and boot OpenWrt with proper MAC addresses.

Installation
1. Prepare TFTP server with OpenWrt initramfs image,
2. Connect to WAN ethernet port,
3. Connect to serial port,
4. Power on the board and enter RedBoot (bootloader) command line by
   pressing Ctrl+C,
5. Enter following commands (replace variables accordingly):
    set_mac (to view MAC addresses)
    alias ethaddr <wan_port_mac_address>
    (confirm storing the value by inputting y and pressing Enter)
    ip_adress -l <board_ip_adress>/24 -h <tftp_server_ip_adress>
    load -r -b 0x80060000 <openwrt_initramfs_image_name>
    exec -c ""
6. Now board should boot OpenWrt initramfs image,
7. Download OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade <openwrt_sysupgrade_image_name>
8. Wait few minutes, after the D2 LED will stop blinking, the board
   is ready for configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-18 20:43:09 +01:00
Tomasz Maciej Nowak
8f6f260302 ath79: routerstation: prepare to use sysupgrade-tar format image
In PR [1] introducing initial support for Ubiquiti RouterStation boards,
Mathias Kresin suggested to replace the combined sysupgrade image with
tarball generated by sysupgrade-tar.sh. This would simplify deployment
of sysupgrade as the kernel size (needed to update FIS partition) could
be simply calculated on the fly instead of reading value from combined
image header. Unfortunately this would break sysupgrade compatibility
between ar71xx image and ath79 image. Therefore this commit creates
migration path to use new sysuprade image, it adds code to accept both
of them at this moment. The plan is to keep it until new stable version
is released. Then the image recipe should be changed to new format and
compatibility code for old image removed.

1. https://github.com/openwrt/openwrt/pull/1237

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-18 20:43:09 +01:00
Tomasz Maciej Nowak
ee34740ca3 ath79: add suport for EnGenius EPG5000
EnGenius EPG5000 (v1.0.0, marketed as IoT Gateway) is a dual band
wireless router.

Specification
SoC:		Qualcomm Atheros QCA9558
RAM:		256 MB DDR2
Flash:		16 MB SPI NOR
WIFI:		2.4 GHz 3T3R integrated
		5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet:	5x 10/100/1000 Mbps QCA8337N
USB:		1x 2.0
LEDS:		4x GPIO controlled
Buttons:	2x GPIO controlled
UART:		4 pin header, starting count from white triangle on PCB
		1. VCC 3.3V, 2. GND, 3. TX, 4. RX
		baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Tools > Firmware,
4. Select OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Alternative installation
1. Prepare TFTP server with OpenWrt sysupgrade image,
2. Connect to one of LAN (yellow) ethernet ports,
3. Connect to UART port (leaving out VCC pin!),
4. Power on router,
5. When asked to enter a number 1 or 3 hit 2, this will select flashing
   image from TFTP server option,
6. You'll be prompted to enter TFTP server ip (default is 192.168.99.8),
   then router ip (default is 192.168.99.9) and for last, image name
   downloaded from TFTP server (default is uImageESR1200_1750),
7. After providing all information U-Boot will start flashing the image,
   You can observe progress on console, it'll take few minutes and when
   the Power LED will stop blinking, router is ready for configuration.

Additional information
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: aigo3d0a0tdagr
useful for creating backup of original firmware.
When doing upgrade from OpenWrt ar71xx image, it is recomended to not keep
the old configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-03-13 16:25:35 +01:00
Jeff Kletsky
fefa34def8 ath79: Add GL.iNet AR-300M-Lite
AR300M-Lite is single-Ethernet variant of the AR300M series
Its eth0 would otherwise be assigned to the WAN interface
making it unreachable firstboot or failsafe.

Installation instructions from OEM (OpenWrt variant):
* Install sysupgrade.bin using OEM's "Advanced" GUI (LuCI),
   * Do not preserve settings
   * Access rebooted device via Ethernet at OpenWrt default address

Add previously missing LED defaults for all three variants;
-nand, -nor, -lite to the definitions in 01_leds

Non-lite variants thanks to Andreas Ziegler
https://patchwork.ozlabs.org/patch/1049396/

Runtime-tested:  GL.iNet AR300M-Lite

Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
2019-03-13 16:25:34 +01:00
Santiago Piccinini
24463d0d94 ath79: add support for LibreRouter v1
Hardware
--------
SOC:   QCA9558
RAM:   128M DDR2
Flash: 16MiB SPI-NOR
ETH:   QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN:   1x Reset
GPIO:  multiple GPIO on header, PoE passthrough enable
UART:  3.3V 115200 8N1 header on the board
WDG:   ATTiny13 watchdog
JTAG:  header on the board
USB:   1x connector and 1x header on the board
PoE:   10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)

OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.

Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
   header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
   interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
    ath> tftp 82000000 <your image>-sysupgrade.bin
    ath> erase 0x9f050000 +$filesize
    ath> cp.b 0x82000000 0x9f050000 $filesize
    ath> bootm 0x9f050000

More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board

Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
2019-03-13 16:25:34 +01:00
Piotr Dymacz
db91418766 ath79: add support for TP-Link RE350K v1
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB

Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).

Warning:
This device does not include any kind of recovery mechanism in U-Boot.

Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Piotr Dymacz
6fa94d5e8f ath79: add support for YunCore A770
YunCore A770 is a ceiling AC750 AP with 2 Fast Ethernet ports, PoE
(802.3at) support, based on QCA9531 + QCA9887.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet (PoE 802.3at support in WAN port)
- 2T2R 2.4 GHz (QCA9531), with ext. PA and LNA
- 1T1R 5 GHz (QCA9887), with ext. FEM (SKY85728-11)
- 2x regular LED, 1x RGB LED (all driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

1. First, gain root access to the device, following below steps:

- Login into web gui (default password/IP: admin/192.168.188.253).
- Go to 'Advanced' -> 'Management' -> 'System' and download backup of
  configuration (bakfile.bin).
- Open the file as tar.gz archive, edit/update 'shadow' file and change
  hash of root password to something known.
- Repack the archive, rename it back to 'bakfile.bin' and use to
  restore configuration of the device.
- After that, device will reboot and can be accessed over SSH.

2. Then, install OpenWrt:

- Login over SSH and issue command:
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
- Upload 'sysupgrade' image and install it (only if previous command
  succeeded) with command: 'sysupgrade -n -F openwrt-...'.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-09 16:31:17 +01:00
Petr Štetiar
40530c8eb4 ath79: Add support for Ubiquiti Nanostation M (XW)
CPU:  AR9342 SoC
RAM:      64 MB DDR2
Flash:     8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN:  2.4/5 GHz
UART:      1 UART
LEDs:        Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:     Reset

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-05 03:15:52 +01:00
Bart Lauret
4386054549 ath79: add support for TP-Link Archer C5 v1
TP-Link Archer C5 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

 - 720 MHz CPU
 - 128 MB of RAM (Various chips)
 - 16 MB of FLASH (Various chips)
 - SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
 - minipcie slot with 3T3R 5 GHz QCA9880-BR4A
 - 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
 - 10x LEDs, 2x software buttons

For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500>

Signed-off-by: Bart Lauret <bblauret@gmail.com>
2019-02-28 11:32:55 +01:00
Roger Pueyo Centelles
59c2f8af8c ath79: add support for COMFAST CF-E120A v3
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.

Specifications:

 - AR9344 SoC
 - 535/400/267 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, both with PoE-in support
 - 64 MB of RAM (DDR2)
 - 8 MB of FLASH
 - 2T2R 5 GHz, up to 25 dBm
 - 11 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new one, so a factory reset will be
 needed. To do so, once the new firmware is flashed, enter into failsafe
 mode by pressing the reset button several times during the boot
 process, while while the WAN LED flashes, until it starts flashing
 faster. Once in failsafe mode, perform a factory reset as usual.

 The U-boot bootloader contains a recovery HTTP server to upload the
 firmware. Push the reset button while powering the device on and
 keep it pressed for >10 seconds. The recovery page will be at
 http://192.168.1.1

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-02-28 11:26:10 +01:00
David Bauer
4ecf2ee4a0 ath79: fix support-list for TP-Link WDR3600
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.

With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-26 23:20:04 +01:00
David Bauer
5568c8a9fe ath79: add ar71xx support-list entry for Fritz4020
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-26 23:20:04 +01:00
INAGAKI Hiroshi
93d4439454 ath79: add support for I-O DATA WN-AC1600DGR
I-O DATA WN-AC1600DGR is a 2.4/5 GHz band 11ac router, based on
Qualcomm Atheros QCA9557.

Specification:

- SoC:      Qualcomm Atheros QCA9557
- RAM:      128 MB
- Flash:    16 MB
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 5x 10/100/1000 Mbps
  - Switch: QCA8337N
- LED/key:  6x/6x(4x buttons, 1x slide switch)
- UART:     through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Alternative flash instruction using initramfs image:

1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing

This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:15 +01:00
Paul Wassi
dee8db441e ath79: proper indentation in image/common-tp-link.mk
Add two spaces for proper indentation in image/common-tp-link.mk

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
79cc48ff60 ath79: rename TP-LINK to TP-Link
Remove inconsistencies in the vendor's name.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
Paul Wassi
ff541c5ca2 ath79: rename TL-WR740ND-v4 to TL-WR740N-v4
Give the device the same name it had in ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-02-14 16:56:14 +01:00
David Bauer
0c24b363a6 ath79: add support for Xiaomi Mi Router 4Q
Hardware
--------
CPU:   Qualcomm Atheros QCA9561
RAM:   64M DDR2
FLASH: 16M SPI-NOR
ETH:   1x WAN - 2x LAN
WiFi:  QCA9561 3T3R
BTN:   1x Reset - 1x WPS
LED:   1x Blue - 1x Red - 1x Yellow
UART:  TX - GND - RX - VCC (From ethernet port)
       115200n8 - 3.3V

Installation
------------
1. Connect to the device via UART.

2. Interrupt the U-Boot on power-on by pressing enter when prompted.

3. Connect you computer to one of the routers LAN ports.
   Assign yourself the IP 192.168.31.10/24.
   Copy the OpenWRT initramfs image to a tftp server root directory.
   Rename the image to 'x4q.bin'.

4. Load the initramfs image to the router by executing following command
   in U-Boot. The image will boot afterwards.

   > tftpboot 0x81000000 x4q.bin; bootm

5. SCP the sysupgrade-image into '/tmp'.
   Remember to assign yourself an IP in 192.168.1.0/24 for this step!

6. Install OpenWRT permanently by executing

   > sysupgrade -n /tmp/<OpenWRT-sysupgrade-image>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-02-11 19:04:06 +01:00
Oldřich Jedlička
12310f05b7 ath79: add support for TP-LINK Archer C7 v4
TP-Link Archer C7 v4 is a dual-band AC1750 router, based on the
Qualcomm/Atheros QCA9561 SoC + QCA9880.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download openwrt-ath79-generic-tplink_archer-c7-v4-squashfs-factory.bin
   and rename it to ArcherC7v4_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
2019-02-05 19:37:31 +01:00
Skirmantas Lauzikas
9c01273e5e ath79: add support for TP-Link Archer C2 V3 (AC900)
This commit adds support for the TP-link Archer C2 V3 (AC900).

Specifications:

 - CPU: QCA9563 750Mhz
 - Ram: 64MB (DDR2)
 - Flash: 8MB (SPI NOR)
 - Ethernet: 5x 10/100/1000
 - Wifi: QCA9563 bgn + QCA9887 an+ac
 - 9x Leds, 2x buttons

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-c2-v3-squashfs-factory.bin
via the router Web interface and flash as normal firmware update.

Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reorder entries, fix trailing whitespace in dts, add firmware partition
 compatible string, remove led default off states, use default on state
 for system led, reuse tplink-safeloader-uimage image build recipe, squash
 with dynamic partitioning commit, reword commit message, add
 installation instructions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2019-01-27 16:41:10 +01:00
Django Armstrong
1c2f7b5115 ath79: add support for Devolo WiFi Pro 1750e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 3T3R (SiGE SE2565T 2.4 GHz power amp x3)
WiFi5: QCA9880 3T3R (Skyworks 5003L1 5 GHz power amp x3)
BTN:   1x Reset
       1x WPS
       1x USB eject
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is pin closest to rear ports)
       Dupont 4 pin header
       Rear RJ45 serial port non-functional
USB:   1x v2.0

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password previously set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: Django Armstrong <iamdjango@hotmail.com>
2019-01-26 21:46:33 +01:00
David Bauer
c8115167f9 ath79: add support for devolo WiFi pro 1200i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
David Bauer
8d68be8057 ath79: add support for devolo WiFi pro 1750i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
Christoph Krapp
59b99e1924 ath79: align GL-AR750S boardname to other GL.iNet devices
As the official device name is GL-AR750S, rename the board accordingly.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-01-01 19:42:41 +01:00
Mathias Kresin
8c485fbb25 ath79: rework elecom-header recipe
Replace the code with a more readable version. Rename the recipe
to reflect the real usecase.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 16:48:49 +01:00
Roger Pueyo Centelles
3dfc07d186 ath79: add support for COMFAST CF-E110N
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.

Specifications:

 - 650/400/216 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, both with PoE-in support
 - 64 MB of RAM (DDR2)
 - 16 MB of FLASH
 - 2T2R 2.4 GHz, up to 26 dBm
 - 11 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new want, so a factory reset will be
 needed: once the new firmware is flashed, perform the factory reset by
 pushing the reset button several times during the boot process, while the
 WAN LED flashes, until it starts flashing quicker.

 The U-boot bootloader contains a recovery HTTP server to upload the
 firmware. Push the reset button while powering the device on and keep it
 pressed for >10 seconds. The recovery page will be at http://192.168.1.1

Notes:

 The device is advertised, sold and labeled as "CF-E110N", but the
 bootloader and the stock firmware identify it as "v2".

Acknowledgments:

 Petr Štetiar <ynezz@true.cz>
 Sebastian Kemper <sebastian_ml@gmx.net>
 Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 16:25:11 +01:00
Georgi Vlaev
d03aae1a09 ath79: add support for TP-Link Archer C6 v2
This patch adds support for TP-Link Archer C6 v2 (EU)

Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board

Flash instructions:

Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
   button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
2018-12-31 16:25:11 +01:00
Guan-Hong Lin
9ebb44aef4 ath79: add support for EnGenius EWS511AP
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.

Short specification:

- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
   (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
   (ath)> erase 0x9f060000 +f50000
   (ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
   (ath)> reset

Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
2018-12-31 16:25:09 +01:00
Paul Wassi
6e78d546d1 ath79: fix boardname of GL.iNet GL-AR300M
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 14:24:21 +01:00
Paul Wassi
cdbf2de777 ath79: Add support for TP-Link WR810N
Device specifications given in b23b0fb28b

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:18:19 +01:00
Paul Wassi
8ba76d6e74 ath79: fix boardname of GL.iNet GL-AR150
This device is called GL-AR150, therefore rename the board
to 'gl-ar150'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:05:26 +01:00
INAGAKI Hiroshi
caf306ce91 ath79: add support for ELECOM WRC-1750GHBK2-I/C
ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac
routers, based on Qualcomm Atheros QCA9563.

This commit also includes small fix; use "0x0x03000101" as pll_1000
instead of "0x03000000".

Specification:

- SoC:      Qualcom Atheros QCA9563
- RAM:      128 MB (DDR2)
- Flash:    16 MB (SPI-NOR)
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 10/100/1000 Mbps
- LED/key:  4x/3x (2x buttons, 1x slide-switch)
- UART:     through-hole on PCB
  - Vcc, RX, GND, TX from switch (QCA8337N) side
  - 115200n8

Flash instruction using factory image:

1. Boot WRC-1750GHBK2-I/C normaly
2. Access to "http://192.168.2.1/" and open firmware upgrade page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, perform sysupgrade with
squashfs-sysupgrade image
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-31 21:38:53 +09:00
Antonio Silverio
9601d94138 ath79: add support for TP-Link TL-WR841N/ND v8
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset

Installation:
Upload the factory image via the vendor-GUI.

Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:31 +01:00
Christoph Krapp
af28d8a539 ath79: add support for GL.iNet GL-AR750S
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.

Furtheremore support for the MicroSD port is not implemented as of now.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
  - Another LED can be accessed on GPIO 7 if soldered

Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:20 +01:00
Weijie Gao
abc7ed2c58 ath79: add support for D-Link DIR-859 A1
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880

USB is supported on the PCB but not connected.

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or the u-boot
   failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted. Otherwise the u-boot
   will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the firmware
   checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
   upgrade the factory.bin through the u-boot failsafe interface and then goto
   step 2.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
David Bauer
e67da34431 ath79: add support for devolo WiFi pro 1750c
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).

It is also not mentioned in the devolo manual.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
David Bauer
1724d4e9ed ath79: add support for devolo WiFi pro 1200e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
TOCK Chiu
8471944325 ath79: add support for TP-Link Archer C7 v5
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.

Specification:
-   QCA9563 SoC (750 MHz)
-   128 MiB of RAM (DDR2)
-   16 MiB of flash (SPI)
-   5x 1 Gbps Ethernet (1x WAN + 4x LAN)
-   2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
-   10x LED, 2x button
-   UART header on PCB

Flash instructions:
1.  Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
    via web interface.

Flash instructions using TFTP recovery:
1.  Plug PC to one of the LAN ports
2.  Set PC to fixed IP address 192.168.0.66
3.  Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
    TFTP root directory
4.  Turn on the router with the reset button pressed for about 15 secs
5.  Release the button and wait about 150 secs to complete flashing

Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
2018-12-27 14:06:38 +01:00
INAGAKI Hiroshi
c566439c9b ath79: add support for NEC Aterm WG800HP
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
  - Vcc, GND, NC, TX, RX from SoC side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-24 19:18:07 +01:00
Mathias Kresin
38cae44e51 ath79: replace cameo-factory with existing build commands
Use pad-offset and append-string to create the cameo factory images for
the D-LINK DIR-825 C1/DIR-835 A1 factory images.

Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-17 23:21:40 +01:00
Christian Lamparter
f54ac91ef5 ar71xx/ath79: switch devices to the -ct driver and firmware
Since commit 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 14:22:28 +01:00
Karl-Felix Glatzer
1e4ee63cc8 ath79: add support for TP-Link Archer A7
This patch adds support for TP-Link Archer A7

Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) SoC internal
  - 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
  - Vcc, GND, RX, TX from ethernet port side
  - 115200n8

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
   root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
   and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing

Changes since first revision:

  - Flash instructions using stock image webinterface
  - Changed "Version 5" in model string to "v5"
  - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
    and qca9563_tplink_archer-a7-v5.dts
  - Firmware image is now build with dynamic partitioning
  - Default to ath10k-ct

Changes since second revision:
  - Changed uboot@0 to uboot@20000 in DTS file
  - Fixed ordering issue in board led script
  - Specify firmware partition format in DTS file
  - Rebased Makefile device definition on common
    Device/tplink-safeloader-uimage definition
  - Merged switch section in network script
    (same configuration as tplink,tl-wdr3600
    and tplink,tl-wdr4300)

Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-17 08:09:13 +01:00
Sebastian Kemper
6c3c4436ee ath79: add d-link dir-825-c1 and dir-835-a1
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.

The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.

https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1
https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1

Installation:

1. Connect to the web interface of the vendor firmware (usually
   listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
   selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.

Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
2018-12-17 00:21:34 +01:00
Marcin Jurkowski
3c3eaa57d9 ath79: add support for TP-Link TL-WR842N/ND v1 router
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.

CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS

AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
2018-12-15 21:35:45 +01:00
INAGAKI Hiroshi
3358cae523 ath79: add support for I-O DATA WN-AG300DGR
I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros
AR1022.

WN-AG300DGR does not have an LED to indicates power or system status,
I set "router" LED as OpenWrt status LED.

There is no eeprom data for 5 GHz wlan in "art" partition.

Specification:

- Atheros AR1022
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4/5GHz wifi
  - 2.4 GHz: SoC internal
  - 5 GHz: Atheros AR93x2
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 6x keys (4x buttons, 1x slide switch)
- 1x USB 2.0 Type-A
- UART through-hole on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WN-AG300DGR
2. Connect power cable to WN-AG300DGR and turn it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-06 20:26:57 +01:00
Chuanhong Guo
9dd7147f6b ath79: add support for Winchannel WB2000
WB2000 is a dual-band 11N AP using AR9344.
The factory firmware used the original DB120 partition table
with a small kernel partition at the end of firmware and the
kernel will easily get oversized in the future. Since it has
to be flashed using UART I also swapped kernel/rootfs and
changed the default load address.

Specification:

- SoC: Atheros AR9344
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 10/100/1000 Mbps (Atheros AR8035)
- 2x USB 2.0
- WIFI: AR9344(2G) + AR9382(5G)
- RTC: DS1338

Known issue:
5G ath9k led doesn't work due to commit ccab68f.

Flash instruction:
Set up a TFTP server on your computer and configure static IP.
Connect UART (J11 TX/GND/RX) and press any key to enter U-boot
shell.
1. Change the default boot command:
   setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000'
   saveenv
2. Set your router ipaddr and server ipaddr. e.g.:
   setenv ipaddr 192.168.1.1
   setenv serverip 192.168.1.50
3. Load and flash the firmware:
   tftp 0x80060000 fw.bin
   erase 0x9f050000 +$filesize
   cp.b $fileaddr 0x9f050000 $filesize
4. Reset your router:
   reset

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Drop the i2c node unit address. Move the ath9k-leds node out of the spi
node, it doesn't belong there. Add the #gpio-cells property to the pci
wifi node. All fix dtc compiler warnings]
Signed-off-by: Mathias Kresin <dev@kresin.me>

merge
2018-12-06 20:26:30 +01:00
Mathias Kresin
dacd962cfd ath79: remove duplicate image build variables
Remove image build variables which are set to the same value as the
default image build recipe.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
Mathias Kresin
9d8fcab77a ath79: fix GL.iNet GL-AR300M sysupgrade
The userspace boardname derived from the dts compatible was out of sync
with the expected board added to the image metadata. This way a
sysupgrade is refused.

Sync the userspace boardname and the baordname used in the image metdata
to allow a seamless sasupgrade.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 13:28:22 +01:00
Chuanhong Guo
c36ec336a3 ath79: rename qca9533.dtsi to qca953x.dtsi
qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE.
Rename the misleading dtsi names and fix the SoC type of gl-ar300m.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[apply the changes for the gl-x750 as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Russell Senior
73127a878d ath79: add support for Ubiquiti AirRouter
Indoor low-power router with 2.4 GHz radio

CPU:    Atheros AR7241 rev 1
RAM:    32 MB
Flash:  8 MB NOR SPI
Switch: Atheros AR7240
Ports:  1x WAN, 4x LAN 10/100 Ethernet
WLAN:   Atheros AR9285 (2.4 GHz)
USB:    1x USB2 host port

Note: Ethernet WAN/LAN port naming is reversed from ar71xx.
WAN is eth0; LAN is eth1.1.

UART settings: 115200, 8N1

                LEDs
        +--------------------------
        |
        |
        |
        |
        |
        |
        |
        |
    VCC | x x
     RX | * x
        | x x
        | x x
     TX | * x
    GND | * x
        |
        |
        |
        |
        +--------------------------
                ETHERNET PORTS

Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-03 07:58:56 +01:00
Rosy Song
31469aebd4 ath79: add support for ROSINSON WR818 board
This commit adds support for the ROSINSON WR818 WiFi-Router

SoC:    Qualcomm Atheros QCA9563,
FLASH:  Winbond W25Q128FV 16MBytes,
WiFi:   QCA9563 b/g/n 3x3 450Mbit/s,
USB:    1x USB 2.0 Type A, 1x USB2.0 Type C,
IN:     WPS/Reset button GPIO1,
OUT:    Power LED red, Internet LED red, WLAN LED red,
        LAN1 LED red, LAN2 LED red, System LED red,
UART:   RX-GPIO18, TX-GPIO22,

Tested and working:
    - Ethernet (LAN + WAN)
    - WiFi
    - OpenWRT sysupgrade
    - Button
    - LEDs

Installation of OpenWRT from vendor firmware:
    - Connect to the Web-interface at http://192.168.1.1
    - Go to "Administration" -> "Firmware Upgrade"
    - Upload the OpenWrt sysupgrade image

Signed-off-by: Rosy Song <rosysong@rosinson.com>
2018-11-27 21:11:54 +01:00
Mathias Kresin
68d77241cd ath79: rename glinet x750
The boardname is gl-x750 and is already used for the led names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
INAGAKI Hiroshi
879f2ef7c0 ath79: modify mtd partitions for Buffalo BHR-4GRV2
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.

In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.

0x50000                       0xe80000        0xff0000
  +-------------------------------+--------------+
  |            rootfs             |    kernel    |
  |           (14528k)            |    (1472k)   |
  +-------------------------------+--------------+

After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.

0x50000                                       0xff0000
  +----------------------------------------------+
  |                   firmware                   |
  |                   (16000k)                   |
  +----------------------------------------------+

However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".

This commit requires new flash instruction instead of the old one.

Flash instruction using initramfs image:

1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
  /dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
  fw_setenv ipaddr 192.168.12.1
  fw_setenv serverip 192.168.12.10
  fw_setenv ethaddr 00:aa:bb:cc:dd:ee
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing

And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 12:28:17 +01:00
David Bauer
946ffe470d ath79: add support for Archer C58/C59 v1
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.

CPU:   Qualcomm QCA9561
RAM:   64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi:  QCA9561 bgn 3x3:3
       QCA9888 nac 2x2:2
LED:   Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
       Only C59: USB
BTN:   WPS, WiFi, Reset

Installation
------------

Via Web-UI:
Update factory image via Web-UI.

Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.

Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 12:05:45 +01:00
Luo chongjun
9989fd5154 ath79: add support for GL-iNet GL-X750
this patch adds supports for GL-X750.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)

Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-11-26 12:05:45 +01:00