mirror of
https://github.com/openwrt/openwrt.git
synced 2025-02-21 09:42:09 +00:00
ath79: add support for TP-Link CPE610-v1
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - Based on the same underlying hardware as the TP-Link CPE510 - Power, LAN, WLAN5G green LEDs - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This commit is contained in:
parent
8a5a01a677
commit
e15049c88b
@ -155,6 +155,9 @@ tplink,cpe210-v3)
|
||||
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "tp-link:green:link3" "wlan0" "60" "100"
|
||||
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "tp-link:green:link4" "wlan0" "80" "100"
|
||||
;;
|
||||
tplink,cpe610-v1)
|
||||
ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0"
|
||||
;;
|
||||
tplink,re450-v2)
|
||||
ucidef_set_led_netdev "lan_data" "LAN Data" "tp-link:green:lan_data" "eth0" "tx rx"
|
||||
ucidef_set_led_netdev "lan_link" "LAN Link" "tp-link:green:lan_link" "eth0" "link"
|
||||
|
@ -25,6 +25,7 @@ ath79_setup_interfaces()
|
||||
pqi,air-pen|\
|
||||
tplink,cpe210-v2|\
|
||||
tplink,cpe210-v3|\
|
||||
tplink,cpe610-v1|\
|
||||
tplink,re350k-v1|\
|
||||
tplink,re450-v2|\
|
||||
tplink,tl-mr10u|\
|
||||
|
140
target/linux/ath79/dts/ar9344_tplink_cpe610-v1.dts
Normal file
140
target/linux/ath79/dts/ar9344_tplink_cpe610-v1.dts
Normal file
@ -0,0 +1,140 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
model = "TP-Link CPE610 v1";
|
||||
compatible = "tplink,cpe610-v1", "qca,ar9344";
|
||||
|
||||
aliases {
|
||||
led-boot = &system;
|
||||
led-failsafe = &system;
|
||||
led-upgrade = &system;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
system: lan {
|
||||
label = "tp-link:green:lan";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan5g {
|
||||
label = "tp-link:green:wlan5g";
|
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy0tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi {
|
||||
num-cs = <1>;
|
||||
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
uboot: partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x000000 0x020000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@20000 {
|
||||
label = "partition-table";
|
||||
reg = <0x020000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
info: partition@30000 {
|
||||
label = "info";
|
||||
reg = <0x030000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "firmware";
|
||||
reg = <0x040000 0x780000>;
|
||||
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "kernel";
|
||||
reg = <0x000000 0x1c0000>;
|
||||
};
|
||||
|
||||
partition@1c0000 {
|
||||
label = "rootfs";
|
||||
reg = <0x1c0000 0x5c0000>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@7c0000 {
|
||||
label = "config";
|
||||
reg = <0x7c0000 0x030000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
art: partition@7f0000 {
|
||||
label = "art";
|
||||
reg = <0x7f0000 0x010000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
|
||||
mtd-cal-data = <&art 0x1000>;
|
||||
mtd-mac-address = <&info 0x08>;
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
|
||||
mtd-mac-address = <&info 0x08>;
|
||||
|
||||
phy-mode = "mii";
|
||||
phy-handle = <&swphy4>;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
compatible = "syscon", "simple-mfd";
|
||||
};
|
@ -146,6 +146,17 @@ define Device/tplink_cpe210-v3
|
||||
endef
|
||||
TARGET_DEVICES += tplink_cpe210-v3
|
||||
|
||||
define Device/tplink_cpe610-v1
|
||||
$(Device/tplink-safeloader)
|
||||
ATH_SOC := ar9344
|
||||
IMAGE_SIZE := 7680k
|
||||
DEVICE_TITLE := TP-Link CPE610 v1
|
||||
TPLINK_BOARD_ID := CPE610V1
|
||||
LOADER_TYPE := elf
|
||||
KERNEL := kernel-bin | append-dtb | lzma | loader-kernel
|
||||
endef
|
||||
TARGET_DEVICES += tplink_cpe610-v1
|
||||
|
||||
define Device/tplink_archer-d50-v1
|
||||
ATH_SOC := qca9531
|
||||
DEVICE_TITLE := TP-Link Archer D50 v1
|
||||
|
@ -278,6 +278,45 @@ static struct device_info boards[] = {
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "support-list",
|
||||
},
|
||||
/** Firmware layout for the CPE610V1 */
|
||||
{
|
||||
.id = "CPE610V1",
|
||||
.vendor = "CPE610(TP-LINK|UN|N300-5|00000000):1.0\r\n",
|
||||
.support_list =
|
||||
"SupportList:\r\n"
|
||||
"CPE610(TP-LINK|EU|N300-5|00000000):1.0\r\n"
|
||||
"CPE610(TP-LINK|EU|N300-5|45550000):1.0\r\n"
|
||||
"CPE610(TP-LINK|EU|N300-5|55530000):1.0\r\n"
|
||||
"CPE610(TP-LINK|UN|N300-5|00000000):1.0\r\n"
|
||||
"CPE610(TP-LINK|UN|N300-5|45550000):1.0\r\n"
|
||||
"CPE610(TP-LINK|UN|N300-5|55530000):1.0\r\n"
|
||||
"CPE610(TP-LINK|US|N300-5|55530000):1.0\r\n"
|
||||
"CPE610(TP-LINK|UN|N300-5):1.0\r\n"
|
||||
"CPE610(TP-LINK|EU|N300-5):1.0\r\n"
|
||||
"CPE610(TP-LINK|US|N300-5):1.0\r\n",
|
||||
.support_trail = '\xff',
|
||||
.soft_ver = NULL,
|
||||
|
||||
.partitions = {
|
||||
{"fs-uboot", 0x00000, 0x20000},
|
||||
{"partition-table", 0x20000, 0x02000},
|
||||
{"default-mac", 0x30000, 0x00020},
|
||||
{"product-info", 0x31100, 0x00100},
|
||||
{"signature", 0x32000, 0x00400},
|
||||
{"os-image", 0x40000, 0x1c0000},
|
||||
{"file-system", 0x200000, 0x5b0000},
|
||||
{"soft-version", 0x7b0000, 0x00100},
|
||||
{"support-list", 0x7b1000, 0x00400},
|
||||
{"user-config", 0x7c0000, 0x10000},
|
||||
{"default-config", 0x7d0000, 0x10000},
|
||||
{"log", 0x7e0000, 0x10000},
|
||||
{"radio", 0x7f0000, 0x10000},
|
||||
{NULL, 0, 0}
|
||||
},
|
||||
|
||||
.first_sysupgrade_partition = "os-image",
|
||||
.last_sysupgrade_partition = "support-list",
|
||||
},
|
||||
|
||||
{
|
||||
.id = "WBS210",
|
||||
|
Loading…
x
Reference in New Issue
Block a user