Only two patches against mainline remains. Switch to v5.10
which works very nicely with all Gemini devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[backported don't disable option CONFIG_BPF_SYSCAL]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Remove upstreamed parts from 100-ubnt_edgerouter2_support.patch.
Compile and runtime tested on Ubiquiti EdgeRouter Lite.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This patch broke while refreshing on a kernel bump. It adds the
config_aneg function twice to the AR8035 PHY now.
Restore the old behavior to restore the patches original intent.
Fixes commit 57e32650ef ("kernel: bump 5.10 to 5.10.31")
Signed-off-by: David Bauer <mail@david-bauer.net>
Use an alternative path to access the CID of the SD card in MMC0, used
for the generation of MAC addresses. With Kernel 5.10, the device name
of the MMC controller changed, breaking MAC address generation.
The new path is compatible with Kernel 5.4 as well as Kernel 5.10.
Signed-off-by: David Bauer <mail@david-bauer.net>
fix the following build error when building with test kernel:
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This feature is already supported in kernel. Add definition
and configuration in Makefile of OpenWRT.
It is tested on board Dibbler with processor V1605B.
Dmesg is as below.
--------------------------------------------
[ 0.317122] smpboot: CPU0: AMD Ryzen Embedded V1605B with Radeon
Vega Gfx (family: 0x17, model: 0x11, stepping: 0x0)
[ 8.227270] libphy: amd-xgbe-mii: probed
[ 8.228189] amd-xgbe 0000:02:00.1 eth0: net device enabled
[ 8.228999] libphy: amd-xgbe-mii: probed
[ 8.229921] amd-xgbe 0000:02:00.2 eth1: net device enabled
.....
[ 11.760869] br-lan: port 1(eth0) entered blocking state
[ 11.761365] br-lan: port 1(eth0) entered disabled state
[ 11.762019] device eth0 entered promiscuous mode
[ 11.785285] 8021q: adding VLAN 0 to HW filter on device eth1
[ 16.881431] amd-xgbe 0000:02:00.1 eth0: Link is Up - 1Gbps/Full -
flow control off
[ 16.882108] br-lan: port 1(eth0) entered blocking state
[ 16.882583] br-lan: port 1(eth0) entered forwarding state
[ 16.883249] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
-----------------------------------------------
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
This updates the NAND driver for MikroTik RB4XX series to work with
kernel 5.10, similarly to the ar934x-nand driver (fb64e2c3).
Support for kernel 5.10 was added to all ath79 subtargets except for the
mikrotik one by commit d6b785d, since patch 920-mikrotik-rb4xx.patch
needed to be reworked. Later, commit f8512661 enabled kernel 5.10 for
the mikrotik subtarget with the nand-rb4xx driver still pending, which
is updated and added back by this patch.
Compile-tested only.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The crypto engine in Armada 370 SoCs is currently broken. It can be
checked installing the required packages for testing openssl with hw
acceleration:
opkg install openssl-util
opkg install kmod-cryptodev
opkg install libopenssl-devcrypto
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Refresh patches.
Tested on a dual-core MT7621 device (Ubiquiti ER-X) and a single-core
MT7621 device (Netgear R6220).
This change will make future kernel upgrades easier (avoids conflicts
with upstream).
Link: https://lore.kernel.org/lkml/20210407200738.149207-1-ilya.lipnitskiy@gmail.com/
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Reduce spi-max-frequency for Xiaomi MI Router 4AG model
Xiaomi MI Router 4AG MTD uses two flash chips (no specific on router versions when produced from factory) - GD25Q128C and W25Q128BV.
These flash chips are capable of high frequency, but due to poor board design or manufacture process.
We are seeing the following errors in the linux kernel bootup:
`spi-nor spi0.0: unrecognized JEDEC id bytes: cc 60 1c cc 60 1c
spi-nor: probe of spi0.0 failed with error -2`
This causes the partitions not to be detected
`VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6`
Then creates a bootloop and a bricked router.
The solution to limit this race condition is to reduce the frequency from 80 mhz to 50 mhz.
Signed-off-by: David Bentham <db260179@gmail.com>
This makes no sense on anything but the IXP4xx platform
that we do not even support anymore. If we bring it back,
it can be selectively enabled for that platform only.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This config is for platforms that have:
A) CONFIG_THERMAL set (we disable it by default)
B) Has thermal zones that need to control cpufreq
This is not suitable for default config, it needs to be enabled
on a per-target basis in individual configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We do not enable GPIO_CDEV so do not enable CDEV_V1
either. As we rebuild the whole userspace and kernel
in OpenWRT it doesn't make any sense to support the
old ABI anyway: the new one should be used by default.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This CMA memory allocation option only applies to NUMA
(Non-Uniform Memory Access) systems which are seldom
the kind of systems that OpenWRT address.
It is safe to assume that any system that need this
option would turn it on locally.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The non-MQ CFQ, deadline and noop IO schedulers are
deleted from the Linux kernel
since commit f382fb0bcef4c37dc049e9f6963e3baf204d815c
"block: remove legacy IO schedulers".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains. No
manual intervention needed.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Removed upstreamed:
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Build system : x86_64
Build-tested : ipq806x/R7800
Run-tested : ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
This patch ist not required, as it only has an effect in case the GPIO
descriptors supplied to num-cs are valid.
As this is not the case for ath79, this patch can safely be omitted. The
issue it tried to fix is actually fixed with
0054-spi-sync-up-initial-chipselect-state.
Signed-off-by: David Bauer <mail@david-bauer.net>
When adding Kernel 5.10 support, the kernel configuration did not
include the LED driver required for the UniFi 6 LR. Also the actual
driver source went missing.
Fixes commit c46ccb69d1 ("mediatek: mt7622: add Linux 5.10 support")
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD.
GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable
or disable transmission, but no change is observed. Therefore, it is
left as output high to ensure the SFP module is forced to transmit.
Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD
1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router
iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port
or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers
950 Mbps symmetric.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Respect the generic kernel config setting, which is "enabled" tree-wide, as
previously done for sunxi.
Ref: 247ef4d98b ("sunxi: enable CONFIG_BPF_SYSCALL and CONFIG_EMBEDDED")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP
boards using a AR8033 SGMII PHY.
Otherwise, 10 Mbit/s links do not transfer data.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite
/ Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes incorrect supported link modes indicated when using ethtool
on the Ubiquiti UniFi AC lite / LR / Mesh.
eroot@OpenWrt:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
The reason for this is, that since kernel 5.4 the PHY capabilities are
read dynamically from the PHY. As Ubiquiti leaves the PHY in a wrong
state, the capabilities of the SGMII side of the PHY are read.
As a side effect, 10 Mbit/s link modes did not work on these boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
From Frank Wunderlich <frank-w@public-files.de>:
Issue were traffic problems after a while with increased ping times if
flow offload is active.
It turns out that key_offset with cookie is needed in rhashtable_params
and head_offset was defined twice.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DTS properties that match *-gpios are treated specially.
Use ngpios instead, as most GPIO drivers upstream do.
Fixes 5.10 DTS errors such as:
OF: /palmbus@300000/gpio@600: could not find phandle
Fixes DTC warnings such as:
Warning (gpios_property): /palmbus@300000/gpio@600:ralink,num-gpios:
Could not get phandle node for (cell 0)
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Use an existing kernel config symbol to fix devices whose ramstart is
not zero. See upstream patch message for more details.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Tobias Wolf <dev-NTEO@vplace.de>
Cc: Daniel Golle <daniel@makrotopia.org>
The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and
does not hold a lock, which causes a race condition when multiple
threads try to access a register, they may get unexpected results.
To avoid this, handle the MDIO lock manually, and use the unlocked
__mdiobus_{read,write} in the critical section.
This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN
operation and the swconfig LED link status poll race between each other.
[1] https://forum.openwrt.org/t/mysterious-vlan-ids-on-mt7621-device/64495
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
CONFIG_MIPS_CMDLINE_FROM_DTB is set to 'y' for all ramips targets
already, which will ensure that the value of 'bootargs' will take
precedence over whatever is in arcs_cmdline.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This fixes partitioning on Linksys EA9500. With this change only the
currently used firmware MTD partition gets parsed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When adding the patch for the missing register, the patch file for the
testing kernel 5.10 was not included.
Fixes commit fbbad9a9a6 ("ath79: force SGMII SerDes
mode to MAC operation")
Signed-off-by: David Bauer <mail@david-bauer.net>
The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default.
This only allows for 1000 Mbit/s links, however when used with an SGMII
PHY in 100 Mbit/s link mode, the link remains dead.
This strictly has nothing to do with the SerDes calibration, however it
is done at the same point in the QCA reference U-Boot which is the
blueprint for everything happening here. As the current state is more or
less a hack, this should be fine.
This fixes the issues outlined above on a TP-Link EAP-225 Outdoor.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Following changes are made to the Lantiq kernel patches:
0001-MIPS-lantiq-add-pcie-driver.patch
The pci header isn't included by the of_pci header any longer
0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
Due to the merge of grx390 and ar10 clocks, extend support to grx390
0025-NET-MIPS-lantiq-adds-xrx200-legacy.patch
The do_carrier arguments was dropped from phy_link_change. The
phylib has always sets the third parameter to true so the flag is
always changed anyway.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
The stuck queue is now passed to xrx200_tx_timeout (the timeout
handler) but not used so far.
0028-NET-lantiq-various-etop-fixes.patch
ioremap has provided non-cached semantics by default since the Linux
2.6 days and was removed with kernel version 5.6.
of_get_phy_mode() returns an error, or 0 on success, and pass a
pointer, of type phy_interface_t, where the phy mode should be
stored now. So far an error wasn't considered. Print at least an
error message if something unexpected happens.
0042-arch-mips-increase-io_space_limit.patch
Move IO space extension to laniq specific file
Signed-off-by: Mathias Kresin <dev@kresin.me>
Duplicate kernel 5.4 config and patches for kernel 5.10.
Duplicate the devicetree source files as well, they need kernel 5.10
specific adjustments.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the device_type property to mark PCI host bridges as such. With
linux 5.10 it is mandatory, otherwise the PCI IO space is flages as PCI
memory and the PCI init fails.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Check if gendisk is already up instead of trying to figure out parent
mtd device (which didn't work well).
Reported-by: DENG Qingfang <dqfext@gmail.com>
Reported-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Fixes: 2809d00007 ("kernel: support FIT partition parser on mtdblock devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz
Memory: 1GB DDR3
Storage: SDcard, native SATA
Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT
USB: 4x USB 2.0
Installation:
Use the standard sunxi installation to an SD-card.
While the board is very similar to the M2 Ultra board
(the V40 is the automotive version of the R40), as both
the u-boot and kernel supports them separately, and some
pins are different, let's add a separate device spec.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Some of bpi-r64 boards have serial NAND attached to SPI bus.
Add SD card image support for installing openwrt to it.
Default to nand upgrade if root device is not mmc block device.
Separate preloader and uboot images for snand are generated.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
The 100-ARM-dts-imx23-introduce-mmc0_sck_cfg.patch does
not need to be copied over as it's already merged upstream.
Other notable change is the USB_CHIPIDEA_OF change to
USB_CHIPIDEA_IMX [1].
[1] https://www.spinics.net/lists/linux-usb/msg193347.html
Compile/runtime-tested on Olinuxino Micro (imx23).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
LPAE should be disabled as the Cortex-A8 cores don't support it,
and the kernel will crash on boot if it's enabled.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Increase the spi-max frequency to 50 MHz, similar to the DIR-842.
Signed-off-by: Jan Forman <forman.jan96@gmail.com>
[improve commit title, fix commit message alignment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased due to movement of rx-offload.c in 5.4.110:
layerscape/patches-5.4/802-can-0002-can-rx-offload-fix-long-lines.patch
layerscape/patches-5.4/802-can-0003-can-rx-offload-can_rx_offload_compare-fix-typo.patch
layerscape/patches-5.4/802-can-0004-can-rx-offload-can_rx_offload_irq_offload_timestamp-.patch
layerscape/patches-5.4/802-can-0005-can-rx-offload-can_rx_offload_reset-remove-no-op-fun.patch
layerscape/patches-5.4/802-can-0006-can-rx-offload-Prepare-for-CAN-FD-support.patch
layerscape/patches-5.4/802-can-0018-can-flexcan-use-struct-canfd_frame-for-CAN-classic-f.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
/dts-v1/; must only be specified once.
Fixes: e887049fbb ("mediatek: add alternative bootchain variant
for UniFi 6 LR")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Move 480-mtd-set-rootfs-to-be-root-dev.patch to hack-5.10 and fix assumption
about the block device index.
Fixes: 2809d00007 ("kernel: support FIT partition parser on mtdblock devices")
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Builds images for the Ubiquiti Network UniFi 6 LR device running the
U-Boot build added by the previous commits.
Everything but MTD partitions is moved to dtsi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow using the FIT block-device partition partition parser to work on
top of mtdblock devices.
This is more tricky than it sounds as it requires to reorganize the
procedure of registering mtdblock devices in order to avoid locking
troubles caused by the block partition parsers then trying to open
the mtdblock device for reading while locks are still being held.
Fix that by moving the adding of the disks after the entire device
has been probed when locks no longer need to be held.
Also address issue with mtdsuper surfaced when using sub-partitions
which prevented mounting JFFS2 using the /dev/mtdblock* device.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
U-Boot has recently added support for having data blobs in uImage.FIT
images stored at offsets after the FDT structure rather than embedding
the data into the FDT structure itself. This is useful as it allows
parts of the image to be mapped by the FIT partition parser, and it
allows the FIT structure itself to be parsed more easily as it usually
fits into single page.
mtdsplit_fit assumed that the total length of an image is identical
to the length of the FDT structure. For uImage.FIT with external data
this assumption no longer holds true.
Add support for uImage.FIT with external data to mtdsplit_fit and in
in that case only split-off rootfs_data -- selecting and mapping rootfs
partition is left to the block partition parser just like on UBI and
block/GPT based platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
commit d6b785d477 ("ath79: add kernel 5.10 support") moved
KERNEL_TESTING_PATCHVER to a subtarget level,
but is looks like Mikrotik subtarget was forgotten.
Also add it for Mikrotik.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
This enables building BCM4908 "raw" image that can be flashed using
bootloader web UI. It requires serial console access & stopping booting
by the "Press any key to stop auto run".
It's easy to build vendor like CHK image but it can't be safely flashed
using vendor UI at this point. Netgear implements method called "NAND
incremental flashing" that doesn't seem to flash bootfs partition as
provided.
Above method seems to update vmlinux.lz without updating 94908.dtb. It
prevents OpenWrt kernel from booting due to incomplete DTB file. Full
Netgear R8000P support can be enabled after finding a way to make vendor
firmware flash OpenWrt firmware including the 94908.dtb update.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
OpenWrt was succesfully tested on the GT-AC5300 model. It's possible to:
1. Install OpenWrt using vendor UI
2. Perform UBI aware sysupgrade
3. Install vendor firmware using OpenWrt sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
bcm4908img is a tool managing BCM4908 platform images. It's used for
creating them as well as checking, modifying and extracting data from.
It's required by both: host (for building firmware images) and target
(for sysupgrade purposes). Make it a host/target package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes boot loader LZMA decompression issue,
reported by GitHub user KOLANICH at [0].
The reported LZMA ERROR has date of 2020-07-20, soon after
the device support landed:
Ralink UBoot Version: 3.5.2.4_ZyXEL
....
3: System Boot system code via Flash.
Image Name: MIPS OpenWrt Linux-4.14.187
Created: 2020-07-20 3:39:11 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1472250 Bytes = 1.4 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
[0] fea232ae8f (commitcomment-45016560)
Fixes: 4dc9ad4af8 ("ramips: add support for ZyXEL Keenetic Lite Rev.B")
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
pcie0 is the same for this generation of Senao APs
while eth0, eth1, and wmac can differ
the qca,no-eeprom property has no effect
for the ath10k drivers
Signed-off-by: Michael Pratt <mcpratt@pm.me>
use qca955x_senao_loader.dtsi
because it is the same hardware / partitioning
and some cleanup
Effects:
nodes to match similar boards
- keys
- eth0
- pcie0
bumps SPI frequency to 40 MHz
removes &pll node:
the property is defined in qca955x.dtsi
removes qca,no-eeprom:
has no effect with mtd-cal-data property
(also spelling)
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This device is a Senao-based product
using hardware and software from Senao
with the tar-gz platform for factory.bin
and checksum verification at boot time
using variables stored in uboot environment
and a 'failsafe' image when it fails.
Extremely similar hardware/software to Engenius EAP1200H
and other Engenius APs with qca955x
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Use a similar upgrade method for sysupgrade.bin, like factory.bin,
for Senao boards with the tar.gz OEM upgrade platform,
and 'failsafe' image which is loaded on checksum failure.
This is inspired by the OEM upgrade script /etc/fwupgrade.sh
and the existing platforms for dual-boot Senao boards.
Previously, if the real kernel was damaged or missing
the only way to recover was with UART serial console,
because the OKLI lzma-loader is programmed to halt.
uboot did not detect cases where kernel or rootfs is damaged
and boots OKLI instead of the failsafe image,
because the checksums stored in uboot environment
did not include the real kernel and rootfs space.
Now, the stored checksums include the space for both
the lzma-loader, kernel, and rootfs.
Therefore, these boards are now practically unbrickable.
Also, the factory.bin and sysupgrade.bin are now the same,
except for image metadata.
This allows for flashing OEM image directly from openwrt
as well as flashing openwrt image directly from OEM.
Make 'loader' partition writable so that it can be updated
during a sysupgrade.
tested with
ENS202EXT v1
EAP1200H
EAP350 v1
EAP600
ECB350 v1
ECB600
ENH202 v1
Signed-off-by: Michael Pratt <mcpratt@pm.me>
ath79/tiny kernel config has
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y
from commit
05d35403b2
Because of this, these changes are required for 2 reasons:
1.
Senao devices in ath79/tiny
with a 'failsafe' partition and the tar.gz sysupgrade platform
and a flash chip that supports 4k sectors
will fail to reboot to openwrt after a sysupgrade.
the stored checksum is made with the 64k blocksize length
of the image to be flashed,
and the actual checksum changes after flashing due to JFFS2 space
being formatted within the length of the rootfs from the image
example:
0x440000 length of kernel + rootfs (from sysupgrade.bin)
0x439000 offset of rootfs_data (from kernel log)
2.
for boards with flash chips that support 4k sectors:
saving configuration over sysupgrade is not possible
because sysupgrade.tgz is appended at a 64k boundary
and the mtd parser starts JFFS2 at a 4k boundary.
for boards with flash chips that do not support 4k sectors:
partitioning with 4k boundaries causes a boot loop
from the mtd parser not finding kernel and rootfs.
Also:
Some of the Senao boards that belong in ath79/tiny,
for example ENH202,
have a flash chip that does not support 4k sectors
(no SECT_4K symbol in upstream source).
Because of this, partitioning must be different for these devices
depending on the flash chip model detected by the kernel.
Therefore:
this creates 2 DTSI files
to replace the single one with 64k partitioning
for 4k and 64k partitioning respectively.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
By using the same custom kernel header magic
in both OKLI lzma-loader, DTS, and makefile
this hack is not necessary anymore
However, "rootfs" size and checksum
must now be supplied by the factory.bin image
through a script that is accepted by the OEM upgrade script.
This is because Senao OEM scripts assume a squashfs header exists
at the offset for the original "rootfs" partition
which is actually the kernel + rootfs in this implementation,
and takes size value from the header that would be there with hexdump,
but this offset is now the uImage header instead.
This frees up 1 eraseblock
previously used by the "fakeroot" partition
for bypassing the OEM image verification.
Also, these Senao devices with a 'failsafe' partition
and the tar-gz factory.bin platform would otherwise require
flashing the new tar-gz sysupgrade.bin afterward.
So this also prevents having to flash both images
when starting from OEM or 'failsafe'
the OEM upgrade script verifies the header magic numbers,
but only the first two bytes.
Example:
[ "${magic_word_kernel}" = "2705" ] &&
[ "${magic_word_rootfs}" = "7371" -o "${magic_word_rootfs}" = "6873" ] &&
errcode="0"
therefore picked the magic number
0x73714f4b
which is
'sqOK'
Signed-off-by: Michael Pratt <mcpratt@pm.me>
...and max flash offset
The mtdsplit parser was recently refactored
to allow the kernel to have custom image header magic.
Let's also do this for the lzma-loader
For example:
When implemented together,
this allows the kernel to "appear" to be a rootfs
by OEM software in order to write an image
that is actually kernel + rootfs.
At the same time,
it would boot to openwrt normally
by setting the same magic in DTS.
Both of the variables
have a default value that is unchanged
when not defined in the makefiles
This has no effect on the size of the loader
when lzma compressed.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
U-Boot uses the "bootpartition" variable stored in
"u-boot-env2" to select the active system partition. Allow
updates to enable system switching from OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
It supports flashing OpenWrt images (bootfs & UBI upgrade) as well as
vendor images (whole MTD partition write).
Upgrading cferom is unsupported. It requires copying device specific
data (like MAC) to target image before flashing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This way MTD "bootfs" partition will be always 8+ MiB. This should be
enough for any custom / future firmware to fit its bootfs (e.g. big
kernel) without having to repertition whole flash. That way we can
preserve UBI and its erase counters during sysupgrade.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The purpose of that dummy file is to make CFE work properly with OpenWrt
bootfs. CFE for some reason ignores JFFS2 files with ino 0.
Rename it to 1-openwrt so:
1. It's consistent with bcm63xx
2. It's OpenWrt specific so sysupgrade can distinguish it from vendor
images
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use update_kernel to refresh all patches, required manual updates to:
610-netfilter_match_bypass_default_checks.patch
611-netfilter_match_bypass_default_table.patch
762-net-bridge-switchdev-Refactor-br_switchdev_fdb_notif.patch
764-net-bridge-switchdev-Send-FDB-notifications-for-host.patch
Run-tested: x86_64
Nothing screamed out but any funny business with linux bridging should
suspect this update first.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Switch the Netgear DTSI for the Realtek target from the OEM partition
naming scheme to accepted OpenWrt naming practices. A quick git grep for
'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas
grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The FRITZ!Box 3390 actually contains two SoCs, one Lantiq with a
5GHz WiFi and one AR9342 with a 2.4GHz WiFi. Only the Lantiq
has access to the flash memory, the Atheros runs fully from RAM.
Specifications
--------------
- Lantiq 500 MHz
- 128MiB RAM
- 128MiB NAND
- 256k Flash
- AR9580 5GHz WiFi
- AR9342 560 MHz
- 64MiB RAM
- AR9328 2.4GHz WiFi
Remarks
-------
This commit only adds support for the Lantiq side of things and
prepares the drivers for communication with the Atheros SoC. Thus,
only 5GHz WiFi works by default, the 2.4GHz WiFi will be added via
another target.
Some kernel patches will be required to add support for the Atheros SoC.
Installation
------------
Use the eva_ramboot.py script to boot the initramfs image. Then, transfer
the sysupgrade image to the device and run sysupgrade to flash it to the
NAND.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Acked-by: Aleksander Jan Bajkowski A.Bajkowski@stud.elka.pw.edu.pl
Signed-off-by: Joachim Cerny <cocktail_yogi@web.de>
"firmware" partition size defined in the device tree file is 0xf70000,
so the right IMAGE_SIZE is 15808k
Fixes: df1e5d6463 ("ramips: fix partition layout of hiwifi hc5x61")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add 5.10 as testing kernel. Builds successfully with
CONFIG_ALL_KMODS=y enabled.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Some common symbols have been moved to target config.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This was done by executing these commands:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
$ make kernel_oldconfig CONFIG_TARGET=subtarget_platform
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1] 9b1b89229f ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Add leds and configs
2. Add network configs
3. Add script to clear partial boot flag
4. Hack to use port 5 as cpu port as port 8 connected to eth2
wont pass any frames
5. Enable EA9500 image generation
Hardware Info:
- Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
- Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125
- DDR3 RAM - 256 MB
- Flash - 128 MB (Toshiba TC58BVG0S3HTA00)
- 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4)
- 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC
- Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch
- Ports - 8 Ports, 1 WAN Ports
- Antennas - 8 Antennas
- Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1
Flashing Instructions:
1. Connect a USB-TTL table to J6 on the router as well as a
ethernet cable to a lan port and your PC.
2. Power-on the router.
3. Use putty or a serial port program to view the terminal.
Hit Ctrl+C and interrupt the CFE terminal terminal.
4. Setup a TFTP server on your local machine at setup you
local IP to 192.168.1.2
5. Start the TFTP Server
6. Run following commands at the CFE terminal
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx
flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2
nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit
7. Reboot router to be presented by OpenWrt
Note: Only installation method via serial cable is supported at the moment.
The trx firmware has to be flashed to both the partitions using following
commands from CFE prompt. This will cover US and Non-US variants.
Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The uImage.FIT partition parser used to squeeze in FIT partitions in
the range where partition editor tools (fdisk and such) expect the
regular partition. This is confusing people and tools when adding
additional partitions on top of the partition used for OpenWrt's
uImage.FIT.
Instead of squeezing in the additional partitions, rather start with
all uImage.FIT partitions at offset 64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes the following error when building without CONFIG_MODULE_STRIPPED:
FATAL: modpost: sound/soc/ralink/snd-soc-ralink-i2s: struct
of_device_id is not terminated with a NULL entry!
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
MIPS Coherent Processor Systems (CPS), which include the MT7621 SoC, support
deep sleep idle states and have a specific cpuidle driver for them.
Enable support for it, while also switching from constant timer ticks to the
idle dynticks model, with the TEO governor.
Run-tested on a Redmi AC2100.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
We've been carrying this patch for many years [1], in order to fix a timer
calibration issue on MT7621. Turns out, after retesting with a recent kernel
(Linux 5.10), the system works perfectly fine without it (no rcu_sched stalls
or inconsistent BogoMIPS values across CPUs).
Manually refreshed:
322-mt7621-fix-cpu-clk-add-clkdev.patch
323-mt7621-memory-detect.patch
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commitdiff;h=6f4a903533361a2906a4d94ac6f597cd9c6c47bc
Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Tested-by: Donald Hoskins <grommish@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The Pine64(+) and the SoPine64 baseboard has two USB ports. One of
these (the lower) is connected directly to a USB host, the other
one's (upper) PHY is shared with the separate OTG controller. In
order to get it working, MUSB support needs to be enabled.
As there are other targets which compile MUSB support into the kernel
and not package it into modules, the same is done here.
[ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364250] usb usb5: Product: MUSB HDRC host driver
[ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd
[ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto
[ 1.379891] hub 5-0:1.0: USB hub found
[ 1.383677] hub 5-0:1.0: 1 port detected
[...]
[ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 697.477180] usb 1-1: Product: USB Flash Disk
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.
But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
There are only two lan ports and one wan port on Youku yk1
Fixes: e9baf8265b ("ramips: add support for Youku YK1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.
Fixes: 50fdc0374b ("ath79: provide label MAC address")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.
The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The CONFIG_USERIO option is unset in multiple target configurations. On
the sunxi target it is activated. Move the kernel configuration option
to the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.
Fixes: 87046e87e2 ("kernel: add missing kernel config symbol")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus
malta (at least) prompted for this new symbol.
Set it to 'false' in the default config. rockchip & X86 enable it in
target specific configs.
Thanks to Tony Ambardar for falling over this one
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This adds detection of the Sophos SG-105 and Sophos XG-105 models
and assignment of ethernet ports these models have to LAN/WAN.
Signed-off-by: Stan Grishin <stangri@melmac.net>
It's helpful for accessing booting data (DTS, kernel, etc.). It has to
be used carefully as CFE's JFFS2 support is quite dumb. It doesn't
recognize deleted files and has problems handling 0 inode.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Populate the recovery and production partitions of the generated sdcard
image for the Bananapi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
After backporting upstream ehci overcurrent patches we need to use spurious-oc
instead of ignore-oc.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch really annoys me, either it needs to go upstream or be
dropped, so it's going to be dropped here.
Checking drivers/platform/x86/pcengines-apuv2.c it also appears to be
incomplete since it mentions different dmi board names depending on bios
version.
/* APU2 w/ legacy BIOS < 4.0.8 */ is 'APU2'
/* APU2 w/ legacy BIOS >= 4.0.8 */ is 'apu2'
/* APU2 w/ mainline BIOS */ is 'PC Engines apu2'
So the patch, if applicable at all, only 'works' for legacy BIOS >=
4.0.8
My APU2 on mainline BIOS reboots fine without this patch. So let's see
if anyone screams and when they do question why legacy bios. If patch
DOES need to be re-introduced then it needs to go upstream first.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Straightforward refresh of patches using update_kernel.
Removed (reverse-applicable):
bmips/patches-5.10/010-v5.11-net-dsa-implement-a-central-TX-reallocation-procedur.patch
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Straightforward refresh of patches using update_kernel.
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
These PCI drivers are a bit hacky and definitely not suitable for upstreaming,
but hopefully we can use them as a base for developing proper upstream PCI
drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Otherwise, the last defined value will be set for all devices.
Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Youku YK-L1 has a huge storage space up to 32 MB. It is better to
use a higher spi clock to read or write serial nor flash chips.
Youku YK-L1 has Winbond w25q256fvfg on board that can support
104 MHz spi clock so 48 MHz is safe enough.
The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz
defined in dts file will set only 48 MHz in spi bus.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add the same patch to 5.10 too. The patch is in process of being
upstreamed.
Fixes: 8cc0fa8fac ("ath79: cfi: cmdset_0002: amd chip
0x2201 - write words")
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device is a wireless router working on 2.4GHz band based on
Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103
wireless chip and Realtek RTL8366RB/S switches. Due to two different
switches being used also two different devices are provided.
Specification:
- 400 MHz CPU
- 64 MB of RAM
- 32 MB of FLASH (NOR)
- 3x3:2 2.4 GHz 802.11bgn
- 5x 10/100/1000 Mbps Ethernet
- 4x LED, 3x button, On/Off slider, Auto/On/Off slider
- 1x USB 2.0
- bare UART header place on PCB
Flash instruction:
- NOTE: Pay attention to the switch variant and choose the image to
flash accordingly. (dmesg / kernel logs can tell it)
- Methods for flashing
- Apply factory image in OEM firmware web-gui.
- Sysupgrade on top of existing OpenWRT image
- U-Boot TFPT recovery for both stock or OpenWRT images:
The device U-boot contains a TFTP server that by default has
an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot
there is a time window, during which the device allows an image to
be uploaded from a client with address 192.168.11.2. The image will
be written on flash automatically.
1) Have a computer with static IP address 192.168.11.2 and the
router device switched off.
2) Connect the LAN port next to the WAN port in the device and the
computer using a network switch.
3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A
arp -s 192.168.11.1 02:AA:BB:CC:DD:1A
4) Initiate an upload using TFTP image variant
curl -T <imagename> tftp://192.168.11.1
5) Switch on the device. The image will be uploaded subsequently.
You can keep an eye on the diag light on the device, it should
keep on blinking for a while indicating the writing of the image.
General notes:
- In the stock firmware the MAC address is the same among all
interfaces so it is left here that way too.
Recovery:
- TFTP method
- U-boot serial console
Differences to ar71xx platform
- This device is split in two different targets now due to hardware
being a bit different under the hood. Dynamic solution within the same
image is left for later time.
- GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device
cover, were the wrong way around and were renamed qos_on -> movie_off,
qos_off -> movie_on. Associated key codes remained the same they were.
The device tree source code is mostly based on musashino's work
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Generally, in upstream CFI flash memory driver uses buffers for write
operations. That does not work with AMD chip with id 0x2201 and we must
resort to writing word sized chunks only. That is, to not apply general
buffer write functionality for this given chip.
Without the patch kernel logs will be flooded with entries like below:
MTD do_erase_oneblock(): ERASE 0x01fa0000
MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985)
MTD do_erase_oneblock(): ERASE 0x01f80000
MTD do_write_buffer(): WRITE 0x01f80000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f8000a.
jffs2: Write clean marker to block at 0x01a60000 failed: -5
MTD do_erase_oneblock(): ERASE 0x01f60000
MTD do_write_buffer(): WRITE 0x01f60000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f6000a.
jffs2: Write clean marker to block at 0x01a40000 failed: -5
References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to usptream fix submission]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Physical port order watched from the back of the device is:
4 / 3 / 2 / 1 / WAN which also matches corresponding leds.
This patch corrects LuCI switch webpage LAN port order.
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[improve commit title, fix sorting in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Improve compatibility of the device tree include file. Now a new .dtsi
file will support both PSG1218A, PSG1218B and K2G.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title, rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
From many teardown image in the internet, I find Phicomm K1/k2 series use
Winbond W25Q64/W25Q128 or GigaDevice GD25Q64/GD25Q128 Flash chips. both of
them support 100+ MHz clock spi operate and fast-read instruction. PSG1218
with W25x or GD25x has been tested and it can run well in OpenWrt v19.07.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
HIWIFI HC5x61 devices support high speed spi clock up to 100+ MHz.
So set spi frequency to 80 MHz here (Due to frequency division the
real clock is 48 MHz).
I have tested HC5661 and it can run well in OpenWrt v19.07.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[adjust commit title and wrap message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is an ASMedia ASM1480 PCIe switch found on mt7622-rfb1 and the
BPi-R64, allowing the user to switch between SATA and PCIe1 which share
the same pins on the SoC.
This chip is not present on the Linksys E8450, it doesn't have SATA.
Remove definitions for GPIO90 from DTSI to prevent it from being
copy&pasted or otherwise causing confusion.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With kernel 5.10, exfat is out of staging and in tree.
Added small hack to make it work with kernel 5.4 as well.
Added removed config options for 5.4 to generic config.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0x900000, size 0x600000
6291456 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "priKernSize";
priKernSize=0x0600000
Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.
Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0xa00000, size 0x400000
4194304 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "pri_kern_size";
pri_kern_size=0x400000
Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.
Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
Update 5.10 generic config to add missing options prompting during builds,
when setting CONFIG_ALL_KMODS. Refresh the x86 subtargets to drop symbols
added to the generic config.
Also fix a typo in 5.4/5.10 generic configs: "CONFIG_CONFIG_KVM_AMD_SEV".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A SPI NOR flash should not be target-specific, so move it to generic in
case another platform needs to use it.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Without that, after merging support to master, the device fails to boot
due to LZMA decompression error:
3: System Boot system code via Flash.
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
. Image Name: MIPS OpenWrt Linux-5.4.99
Created: 2021-02-25 23:35:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1786664 Bytes = 1.7 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:80040 len:1b4328
............................ Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
Use lzma-loader to fix it.
Fixes: 59d065c9f8 ("ramips: add support for ZTE MF283+")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
HC5661 does not have USB port, remove usb power control pin.
HC5x61 do not have LAN LEDs, remove ethernet LED control pin.
Only HC5861 has PA in 2.4G channel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.
Set maximum kernel size and disable image building for this board.
Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Signed-off-by: David Bauer <mail@david-bauer.net>
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Bananapi BPi-R64 got a SATA interface which cannot be used at the
same time as the second mPCIe slot. The decission is made by hogging
GPIO 90.
Embed two addtional DT overlay blobs into the image to allow bootloader
selection of either SATA or PCIE1 feature.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).
Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop autogenerated kernel config options. These aren't needed to build and
can obscure options relevant to the subtarget.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update generic config to add missing options that prompt during builds. Run
"make kernel_oldconfig" to refresh malta target config.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.
1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
There is no need to define a static link or a phy for the sfp
ports. Using phy-mode and managed properties to describe the
link to the sfp phy.
We have to keep the now unconnected virtual "phys" because the
switch driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.
Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
From the validate docs in include/linux/phylink.h:
When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
MAC driver to return all supported link modes.
Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
This is a temporary workaround to get the ethernet working, since external
switch is connected by MDIO and it needs additional work.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport upstream patch that fixes TRGMII mode now that mt7530 is
actually resetting the switch on ramips devices.
Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both.
Fixes: 69551a2442 ("ramips: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
The 5.10 target config defined a baseline i686 CPU aligned to the 32-bit
generic subtarget. However, the legacy subtarget arch wasn't set to the
older 586MMX, defaulting instead to the i686.
Explicitly set the subtarget arch and refresh the subtarget config, as done
already with the old geode subtarget.
Fixes: 8391781389 ("x86: support kernel 5.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
kmod-mt7615e kmod-mt7615-firmware and uboot-envtools are already part
of the target's default package set. No need to add them again for
buffalo_wsr-2533dhp2.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the Buffalo WSR-2533DHP2.
The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.
There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image
Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.
1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.
Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash
1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.
Specifications
-------------------
* SoC: MT7622 (4x4 2.4 GHz Wifi)
* Wifi: MT7615 (4x4 5 GHz Wifi)
* Flash: Winbond W29N01HZ 128MB SLC NAND
* RAM 256MB
* Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s)
Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Buffalo uses the TRX format with a different magic, add support for
this.
It is planned to send these patches upstream.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes some bugs in the mtk parallel nand driver introduced in 5.10.
This patch was send upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* clean up whitespace to make GPT partitioning more readable
* don't select packages already part of the target default selection
* don't select U-Boot variants (breaks ImageBuilder)
* don't select AHCI on boards without SATA
* don't select kmod-usb2 and kmod-ohci, USB 1.x and USB 2.0 devices
work fine with the in-SoC XHCI host having just kmod-usb3 installed.
* select kmod-btmtkuart for devices with Bluetooth support
* sort DEVICE_PACKAGES
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some patches were slightly cleaned up. One things worth mentioning is
that adding:
phy-mode = "rgmii"
broke SF2 driver. It made it access random register breaking switch
setup.
That's why this commit also adds a quick sf2 fix.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add linux 5.10 as testing kernel, copy generic/subtarget configs and target
patches from 5.4.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
x86: update target patches for kernel 5.10
Refresh all patches while also dropping:
800-hwmon-w83627ehf-dont-claim-nct677x.patch
which is now upstreamed as:
3207408ab4cb ("hwmon: (w83627ehf) remove nct6775 and nct6776 support")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
x86: refresh 5.10 target config
Refresh config using "make kernel_oldconfig".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
x86: refresh and test all subtarget configs
Refresh configs using "make kernel_oldconfig CONFIG_TARGET=subtarget".
Build and run-tested using QEMU: x86/64, x86/legacy, x86/generic.
Build-tested only: x86/geode.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[squashed commits]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add kmod-mdio-devres package and kernel config symbol, and update related
kmod-r8169 and kmod-ixgbe package dependencies.
Build tested module dependencies on x86/64 with CONFIG_ALL_KMODS=y.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds experimental ethernet support for BCM6318, BCM6328, BCM6362, BCM6368
and BCM63268.
BCM6358 needs a different driver, so there's no support for now.
Working devices:
- Comtrend AR-5315u
- Comtrend AR-5387un
- Comtrend VR-3025u
- Comtrend VR-3032u
Not working devices:
- Netgear DGND3700 v2 (no idea on how the external switch is connected)
- Huawei HG556a ver B (BCM6358 needs a separate driveer)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Make some cosmetic changes in the Buffalo LinkStation LS421DE NAS:
- Delete pointless #xxx-cells
- bootargs: replace earlyprintk with earlycon and remove unneeded args.
- Separate pinmux nodes with empty lines.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
dd on Mac OS X apparently fails when using 'M' unit for bs.
dd: bs: illegal numeric value
Use 'k' unit instead for 'pad-to' to fix that.
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
NVRAM access may be needed early in boot process. Reading it using mtd
happens quite late in the init process. Add NVRAM initialization to the
NVMEM driver which comes up early and depends on IO mapping only.
This is required by Linksys devices which use NVRAM content for proper
partitioning (detecting current firmware partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Demote a number of debugging printk's to pr_debug to avoid log
nosie. Several of these functions are called as a result of
userspace activity. This can cause a lot of log noise when
userspace does periodic polling.
Most of this could probably be removed completely, but let's
keep it for now since these drivers are still in development.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
It supports NVRAM access described using DT binding. Right now NVRAM
data is exposed using /sys/bus/nvmem/ only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Introduce new patch for automatically detecting RAM size.
Some boards have a different amount of RAM depending on the HW revision.
Therefore, automatically detecting the RAM size instead of hard-coding it will
reduce the number of device definitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Sercomm AD1018 has a NAND flash. We recently added support for NANDs
in this target.
Use the internal NAND as additional storage.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
This was added recently and thus overlooked in 85b1f4d8ca
("treewide: remove execute bit and shebang from board.d files").
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader of many ipq806x boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq806x.
(ipq807x is unaffected as DEVICE_DTS_CONFIG default is set
"config@hk01" in target/linux/ipq807x/image/Makefile)
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The in-SoC RTC of the Bananapi R64 is more disruptive than useful
without a battery connected. Disable it to not have Linux use the
RTC provided time 2000-01-01 00:00:00 after power-loss.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable testing kernel.
Fix compile errors by using new kernel APIs.
Fix fuzz by manually editing patches to ensure the code goes in the
right place.
For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.
Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.
Run automatic quilt refresh on the rest.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
0098-disable_cm.patch is not needed because upstream fixed CM handling.
The rest are straightforward removals of upstreamed patches.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This reverts commit b4aad29a1d.
This was accidentally folded into a single commit. Remove it and
apply it properly again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It appears to be an automatic Kconfig symbol that varies depending on
the host platform. There is no need to define it in target configs, so
filter it out.
Also sort config-filter entries alphabetically.
Cc: Adrian Schmutzler <mail@adrianschmutzler.de>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Enable testing kernel.
Delete upstreamed patches:
0098-disable_cm.patch can be dropped, upstream fixed CM handling.
Fix compile errors by using new kernel APIs.
Fix fuzz by manually editing patches to ensure the code goes in the
right place.
For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.
Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.
Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.
Run automatic quilt refresh.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
