Commit Graph

1536 Commits

Author SHA1 Message Date
Daniel Golle
41c053141e mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblk
No bootloader changes needed in this case, smooth transition.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
208f6c1232 mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblk
Modernize bootloader and flash memory layout of the BPi-R64 similar to
how it has also been done for the BPi-R3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
8f9b10d917 arm-trusted-firmware-mediatek: add UBI-enabled builds for MT7622
Use custom UBI start address 0x80000 on MT7622 which is more than
enough for a single bl2 (MT7622 BootROM doesn't support redundant bl2).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
8afce4893b uboot-envtools: mediatek_filogic: update bpi-r3
Unify env configuration now that BPi-R4 and BPi-R3 both use fitblk.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
033db3a95d uboot-mediatek: bpi-r3: all-UBI NAND layout, use fitblk
Modernize U-Boot to provide a better reference:
 * store fip image in UBI now that TF-A supports that
 * switch from uImage.FIT partition parser to new fitblk
   virtual firmware block driver (root=/dev/fit0)
 * automatically set root device according to boot_mode register

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
91b55ca4c8 arm-trusted-firmware-mediatek: add mt7986-spim-nand-ubi-ddr4
Add UBI-enabled build for MT7986 with SPIM-NAND and DDR4 for use with
the BananaPi R3 board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
1192554d56 uboot-envtools: filogic: add support for BananaPi R4
Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
13ddc65b2c uboot-envtools: filogic: de-duplicate UBI env settings
Use function instead of duplicating the env settings on UBI for
OpenWrt-built U-Boot over and over.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:30:08 +00:00
Daniel Golle
74a8f416f4 uboot-mediatek: update to U-Boot 2024.01 release
Rebase local patches on top of quarterly timed release, allowing to
drop numerous patches which have been accepted upstream since the
release of U-Boot 2023.07.02.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:37 +00:00
Daniel Golle
54f99ebe5c uboot-mediatek: add build for BPi-R4
Add build for the BananaPi R4 board which can boot from micro SD,
SPI-NAND or eMMC.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:37 +00:00
Daniel Golle
b165d451bd uboot-mediatek: mt7988: set rootdisk according to boot device
If nodes /chosen/rootdisk-${bootdevice} exists, set /chosen/rootdisk
phandle according to boot device selected by the bootstrap pins.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:37 +00:00
Daniel Golle
89fcf211cb uboot-mediatek: fix MMC erase timeout
When erasing large amounts of blocks at once this can take a long
time on slow cards. Instead of a fixed timeout, wait longer if more
blocks are being erased.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:37 +00:00
Daniel Golle
927334a8f7 uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)
Add basic U-Boot drop-in replacement compatible with the flash layout
of the vendor loader of the Zbtlink WG3526 (16M) MT7621 router board.
The idea here is a to have a reference build of uboot-mediatek also for
a simple MIPS boards more popular than MT7621 RFB.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:37 +00:00
Daniel Golle
7cecabbe34 arm-trusted-firmware-mediatek: use UBI on new NAND targets
Make use of recently added UBI support in MediaTek's ARM
TrustedFirmware-A on new MT7988 SoC.

Load fip from static UBI volume instead of fixed offset on SPIM-NAND
and SNFI.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:36 +00:00
Daniel Golle
c55c56b3fd arm-trusted-firmware-mediatek: set HIDDEN=y
Hide arm-trusted-firmware-mediatek packages from interactive config.
Exposing them only causes confusion and needed variants are anyway
selected as dependencies by uboot-mediatek packages.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-15 19:06:36 +00:00
Shiji Yang
3b74ae780c uboot-envtools: backport some usefull patches from v2024.04-rc1
Highlights:
- Silence small page read warning.
- Autodetect NAND erase size and env sectors.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-02-11 10:48:59 +01:00
Nick Hainke
5a016cc3af uboot-envtools: update to 2024.01
Update to latest version.

Refresh patches:
- 002-Revert-tools-env-use-run-to-store-lockfile.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-02-09 13:55:18 +01:00
Nick Hainke
1c02b874fa kexec-tools: update to 2.0.28
Release Notes:
- https://www.spinics.net/lists/kexec/msg32139.html
- https://www.spinics.net/lists/kexec/msg33447.html

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-02-06 12:10:05 +01:00
David Bentham
d8f4453bf2 mediatek: add Comfast CF-E393AX support
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.

Oem firmware is a custom openwrt 21.02 snapshot version.

We can gain access via ssh once we remove the root password.

Hardware specification:
  SoC: MediaTek MT7981A 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB DDR3
  Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
            1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976D
  LEDS: 1x (Red, Blue and Green)
  Button: Reset
  UART: 3.3v, 115200n8
  --------------------------
  | Layout |
  | ----------------- |
  | 4 | VCC GND TX RX | <= |
  | ----------------- |
  --------------------------

Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
   and download the
   configuration(http://apipaddress/computer/config.html).

2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
   Enter 'fakeroot' command then decompress the configuration:
   tar -zxf backup.tar.gz

3. Edit 'etc/shadow', update (remove) root password:
   With password =
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   to
   Without password =
   'root::0:99999:7:::'
   'root::0:99999:7:::'

4. Repack 'etc' directory back to a new backup file:
   tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
   Exit fakeroot - 'exit'

6. Upload new configuration via web interface, now you
   can SSH with the following:

   'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.

   Backup the mtd partitions
   - https://openwrt.org/docs/guide-user/installation/generic.backup

7. Copy openwrt factory firmware to the tmp folder to install via ssh:

   'scp -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa \
   *-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
   root@192.168.10.1:/tmp/'

   'sysupgrade -n -F \
   /tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'

8. Once led has stopped flashing - Connect via ssh with the
   default openwrt ip address - 'ssh root@192.168.1.1'

9. SSH copy the openwrt sysupgrade firmware and upgrade
   as per the default instructions.

Signed-off-by: David Bentham <db260179@gmail.com>
2024-02-02 13:01:38 +01:00
Chuanhong Guo
1b7e62b20b mediatek: drop NMBM layout for Xiaomi WR30U
This reverts commit dcdcfc1511.

This is a firmware for third-party u-boot mod, which should not
be carried here by us.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2024-01-23 19:24:32 +08:00
Tianling Shen
7939df9587 uboot-rockchip: Update to 2024.01
Runtime tested on Orange Pi R1 Plus LTS and NanoPi R4S.

Removed upstreamed patches:
- 100-rockchip-rk3328-Add-support-for-Orange-Pi-R1-Plus.patch
- 101-rockchip-rk3328-Add-support-for-Orange-Pi-R1-Plus-LT.patch
- 103-rockchip-rk3568-Add-support-for-FriendlyARM-NanoPi-R.patch
- 104-rockchip-rk3568-Add-support-for-FriendlyARM-NanoPi-R.patch

Refreshed remaining patches.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-01-20 21:11:22 +01:00
Tianling Shen
d531c34479 arm-trusted-firmware-rockchip: Update to 2.10
Runtime tested on Orange Pi R1 Plus LTS (RK3328) and NanoPi R4S (RK3399).

Changelog: https://trustedfirmware-a.readthedocs.io/en/v2.10/change-log.html

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-01-20 21:11:22 +01:00
Linus Walleij
f1a447bdb5 uboot-bcm53xx: bump to 2024.01
Bump the U-Boot version used for BCM53xx to the 2024.01
version that includes all the needed patches upstream, so we
can get rid of those in the process.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-01-20 19:38:20 +01:00
Tianling Shen
c0c3234e17 mediatek: add support for JDCloud RE-CP-03
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: 128GB eMMC
  RAM: 1GB DDR4
  Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Joylink
  Power: DC 12V 2A

Flash instructions:
1. Download and flash the vendor migration firmware via webUI:
   https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin
   (Default address is 192.168.68.1, user root, no password)
2. After device has booted up, write new GPT table:
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-01-19 21:43:32 +01:00
Tianling Shen
6fa4fbbc52 uboot-mediatek: add support for JDCloud RE-CP-03
The vendor U-Boot has enabled signature verification, so add
a custom U-Boot build for OpenWrt.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-01-19 21:43:32 +01:00
Dim Fish
7dbcc1215a mediatek: filogic: add support for Xiaomi AX3000T
**SoC**: MediaTek MT7981B 2x A53
  **Flash**: ESMT F50L1G41LB 128MB
  **RAM**: NT52B128M16JR-FL 256MB
  **Ethernet**: 4x 10/100/1000 Mbps
  **Switch**: MediaTek MT7531AE
  **WiFi**: MediaTek MT7976C
  **Buttons**: Reset, Mesh
  **Power**: DC 12V 1A

1. Get ssh access. Supported stock firmware **1.0.47**
   ```
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A
   ```

2. Backup stock partitions
   ```
   nanddump -f /tmp/BL2.bin /dev/mtd1
   nanddump -f /tmp/Nvram.bin /dev/mtd2
   nanddump -f /tmp/Bdata.bin /dev/mtd3
   nanddump -f /tmp/Factory.bin /dev/mtd4
   nanddump -f /tmp/FIP.bin /dev/mtd5
   nanddump -f /tmp/ubi.bin /dev/mtd8
   nanddump -f /tmp/KF.bin /dev/mtd12
   ```
   Then transfer them to your computer in a safe place.

3. Get firmware information `cat /proc/cmdline`

4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash
   If **firmware=0**
   ```
   ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=1
   nvram set flag_last_success=1
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```
   If **firmware=1**
   ```
   ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=0
   nvram set flag_last_success=0
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```

   Then reboot your router, it should boot to the OpenWrt initramfs system now.

5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin`

1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

   `reboot`

2. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

3. Format ubi and create new ubootenv volume
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
   ```

4. *(Optional **-10Mb** free space) Add recovery boot feature.*
   ```
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
   ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   ```

5. Flash Openwrt U-Boot
   ```
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP
   ```

6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb`

1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

2. Format ubi and Nvram
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   mtd erase Nvram
   ```

3. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Flash stock images from backup
   ```
   mtd write /tmp/BL2.bin BL2
   mtd write /tmp/FIP.bin FIP
   mtd write /tmp/ubi.bin ubi
   ```
   Then reboot your router, waiting it finished rollback in minutes.

   `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
   Then reboot your router, waiting it finished rollback in minutes.

Signed-off-by: Dim Fish <dimfish@gmail.com>
2024-01-06 17:51:11 +01:00
Mohammad Sayful Islam
46a2490e8f ipq807x: add support for Linksys MX4200 V1 and V2
Linksys MX4200 is a 802.11ax Tri-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 512Mb NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
	* RGB system led

* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack

Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part

- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel

- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel

Replace (X) with your model version either 1 or 2

Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2024-01-06 16:13:23 +01:00
Roland Reinl
fdb87a91b4 mediatek: Add support for D-Link EAGLE PRO AI R32
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.

Specification:
 - MT7622BV SoC with 2.4GHz wifi
 - MT7975AN + MT7915AN for 5GHz
 - MT7531BE Switch
 - 512MB RAM
 - 128 MB flash
 - 2 LEDs (Status and Internet, both can be either orange or white)
 - 2 buttons (WPS and Reset)

Compared to M32, the R32 has the following differences:
 - 4 LAN ports instead of 2
 - The recory image starts with DLK6E6015001 instaed of DLK6E6010001
 - Individual LEDs for power and internet
 - MAC address is stored at another offset in the ODM partition

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x81
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Flashing via Recovery Web Interface:
 - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the deivce
 - Keep the reset button pressed until the internet LED blinks fast
 - Open a Chromium based and goto http://192.168.0.1
 - Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin

Flashing via uBoot:
 - Open the case, connect to the UART console
 - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
 - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
 - Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
 - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
 - Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
 - Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
 - Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
 - Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the deivce
 - Keep the reset button pressed until the internet LED blinks fast
 - Open a Chromium based and goto http://192.168.0.1
 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
 - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
 - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
 - Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
 - Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin

Revert back to stock using uBoot:
 - Open the case, connect to the UART console
 - Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides the previously created backup of the Kernel1 partition.
 - You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
 - Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to FLASH will start. After a few seconds the stock firmware should start again

There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.

Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
 - The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
 - The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
 - OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
2024-01-02 21:22:46 +01:00
Xavier Franquet
782eb05008 mediatek: filogic: add support ASUS RT-AX59U
(based on support for ASUS RT-AX59U by liushiyou006)

SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)

Upgrade from AsusWRT to OpenWRT using UART

    Download the OpenWrt initramfs image.
    Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.

    Connect the PC with TFTP server to the RT-AX59U.
    Set a static ip on the ethernet interface of your PC.
    (ip address: 192.168.1.70, subnet mask:255.255.255.0)
    Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.

    Download & Boot the OpenWrt initramfs image.

    $ setenv ipaddr 192.168.1.1
    $ setenv serverip 192.168.1.70
    $ tftpboot 0x46000000 rtax59u.bin
    $ bootm 0x46000000

    Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.

    $ sysupgrade -n <path-to-sysupgrade.bin>

Upgrade from AsusWRT to OpenWRT using WebUI

    Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq

    Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file

    Wait for OpenWRT to boot (192.168.1.1).

    Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command

MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.

              : Stock             : OpenWrt
  WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
  WLAN 2g (2) :                   : CA:xx:xx:0D:xx:D4
  WLAN 2g (3) :                   : CE:xx:xx:0D:xx:D4
  WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
  WLAN 5g (2) :                   : CE:xx:xx:1D:xx:D5
  WLAN 5g (3) :                   : C2:xx:xx:1D:xx:D5

  WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
  WLAN 2g (2) :                   : 0A:xx:xx:76:xx:BE
  WLAN 2g (3) :                   : 0E:xx:xx:76:xx:BE
  WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
  WLAN 5g (2) :                   : 0E:xx:xx:76:xx:BF
  WLAN 5g (3) :                   : 02:xx:xx:76:xx:BF

Signed-off-by: Xavier Franquet <xavier@franquet.es>
2023-12-31 00:03:24 +01:00
Mikhail Zhilkin
485adc9d3c mediatek: add support for Routerich AX3000
This PR is continuation of work under "mediatek: add support for Routerich
AX3000" #13703 by the agreement with PR #13703 original author (Maximilian
Weinmann <x1@disroot.org>). All reviews from the previous PR were taken
into into account.

Routerich AX3000 is a wireless WiFi 6 router.

Specification
-------------
- SoC       : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM       : DDR3 256 MiB (ESMT M15T2G16128A)
- Flash     : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN      : MediaTek MT7976CN dual-band WiFi 6
  - 2.4 GHz : b/g/n/ax, MIMO 2x2
  - 5 GHz   : a/n/ac/ax, MIMO 2x2
- Ethernet  : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
- USB       : 1x 2.0
- UART      : through-hole on PCB
  - [J500] GND, TX, RX, 3.3V (115200n8)
- Buttons   : Mesh, Reset
- LEDs      : 1x Power (Blue)
              1x WiFi 2.4 GHz (Blue)
              1x WiFi 5 GHz (Red)
              1x Mesh (Blue)
              3x LAN activity (Blue)
              1x WAN activity (Blue)
              2x WAN no-internet (Red)
- Power     : 12 VDC, 1.5 A

Installation
------------
Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface
(without keeping settings).

Return to stock
---------------
Install stock firmware image (without keeping settings) using OpenWrt
sysupgrade method.

Recovery
--------
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 24:0f:5e:xx:xx:b4 | label     |
| LAN     | 24:0f:5e:xx:xx:b5 | label+1   |
| WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2   |
| WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3   |
+---------+-------------------+-----------+
The WLAN 2g MAC was found in 'Factory', 0x4

Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-12-26 17:17:23 +01:00
Ian Oderon
4300bc6688 mediatek: add support for Zbtlink ZBT-Z8103AX
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.

Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi

Buttons:
Reset-Mesh

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Signed-off-by: Ian Oderon <ianoderon@gmail.com>
2023-12-26 00:02:19 +01:00
Tianling Shen
4cc6e7192f
arm-trusted-firmware-sunxi: Update to 2.10
Runtime tested on NanoPi R1S H5 and Orange Pi Zero3.

Changelog: https://trustedfirmware-a.readthedocs.io/en/v2.10/change-log.html

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-12-20 10:53:48 +08:00
Rafał Miłecki
de94eceee6 uboot-envtools: bump PKG_RELEASE
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-12-13 08:53:36 +01:00
Rafał Miłecki
3ed7abfc5a uboot-envtools: fix reading NVMEM device's compatible value
Fixes: fea4ffdef2 ("uboot-envtools: update to 2023.04")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-12-13 08:52:23 +01:00
Mikhail Zhilkin
f3cdc9f988 ramips: add support for Rostelecom RT-FE-1A
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Power (green, unmanaged)
   - 1x Status (green, gpio)
   - 1x 2.4G (green, hardware, mt76-phy0)
   - 1x 2.4G (blue, gpio)
   - 1x 5G (green, hardware, mt76-phy1)
   - 1x 5G (blue, gpio)
   - 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------

1.  Login to the router web interface (default http://192.168.0.1/)
    under "admin" account

2.  Navigate to Settings -> Configuration -> Save to Computer

3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
    cfgtool.py -u configurationBackup.cfg

4.  Open configurationBackup.xml and find the following block:

<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>

5.  Replace <some value> by a new superadmin password and add a line
    which enabling superadmin login after. For example, the block after
    the changes:

<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>

6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml

7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router

8.  Login to the router web interface (superadmin:xxxxxxxxxx, where
    xxxxxxxxxx is a new password from the p.5)

9.  Enable SSH access to the router (Settings -> Access control -> SSH)

10. Connect to the router using SSH shell using superadmin account

11. Run in SSH shell:
    sh

12. Make a mtd backup (optional, see related section)

13. Change bootflag to Sercomm1 and reboot:
    printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
    reboot

14. Login to the router web interface under admin account

15. Remove dots from the OpenWrt factory image filename

16. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
   cd /tmp
   for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
   tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
   tftp -l mtd.md5 -p 192.168.0.2

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g  | label + 2  | f4:*:68 |
| 5g  | label + 3  | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-12-06 00:12:56 +01:00
David Bauer
dd5d4e24af uboot-envtools: fix GL-MT2500 offset
The previous offsets did also work, as they've wrapped back to 0x0.
However, in reality the environment starts at offset 0x0 of the
u-boot-env MMC partition.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-12-03 06:56:02 +01:00
David Bauer
1239668648 mediatek: add support for GL.iNet GL-MT2500
Hardware
--------
SoC:  MediaTek MT7981BA
RAM:  1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC:  8GB eMMC (Samsung 8GTF4R)
ETH:  1000Base-T LAN (ePHY)
      2500Base-T WAN (MaxLinear GPY211C)
BTN:  1x Reset Button
LED:  System (blue/white)
      VPN (white)
USB:  1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
      Don't connect 3.3V!

Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!

Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-11-27 08:02:41 +01:00
Tianling Shen
e2cea0506a uboot-rockchip: add NanoPi R5C support
Add support for the FriendlyARM NanoPi R5C.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
2670bb4a83 uboot-rockchip: add NanoPi R5S support
Add support for the FriendlyARM NanoPi R5S support.

Tested-by: Packet Please <pktpls@systemli.org>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
b061e2d890 rkbin: add new TF-A package for rk35xx
Currently there's no usable mainline (open source) TF-A implementation
for rk35xx SoCs, so pack the prebuilt firmware from the vendor.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
548ab9d7ad uboot-rockchip: Update to 2023.07.02
* Removed swig hacks and prebuilt of-platdata
* Removed upstreamed patches
  - 101-rock64pro-disable-CONFIG_USE_PREBOOT.patch
  - 102-rockchip-rk3328-Add-support-for-FriendlyARM-NanoPi-R2C.patch
* Reordered patches

* Introduced new dependencies check
* Overrided default PATH to avoid race condition
    (host python3 vs hostpkg python3)
* Switched to use UBOOT_CUSTOMIZE_CONFIG for config update

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
8fc4fe7b48 uboot-sunxi: use intree dtc explicitly
This replaces pylibfdt hack.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
fb3af86119 uboot-sifiveu: use intree dtc explicitly
This replaces pylibfdt hack.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Tianling Shen
20f81f49ea uboot-mediatek: use intree dtc explicitly
This replaces pylibfdt hack.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-11-26 19:44:56 +01:00
Rani Hod
e29f4a3f70 ath79: add support for D-link DAP-1720 A1
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)

Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
  775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
  64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
  16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
  1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
  * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
    3x3 802.11n;
  * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
    3x3 802.11ac Wave 1;
  * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
  * RSSI low (red/green) [D2];
  * RSSI medium (green) [D3];
  * RSSI high (green) [D4];
  * status (red/green) [D5];
* GPIO buttons:
  * WPS [SW1], co-located with status LED;
  * reset [SW4], accessible via hole in the side;
* Serial/UART:
  Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
  125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
  * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
  * on/off slide switch [SW2] (disconnects VCC mechanically);
  * unpopulated footprints for a Wi-Fi LED [D1];
  * unpopulated footprints for a 4-pin 3-position slide switch (SW3);

MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;

Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
  standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
  firmware) from D-Link Web Recovery. To enter web recovery, keep reset
  button pressed and then power on the device. Reset button can be
  released when the red status LED is bright; it will then blink slowly.
  Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
  upload 'recovery.bin'. Note that in web recovery mode the device
  ignores ping and DHCP requests.

Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.

Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
2023-11-26 18:27:35 +01:00
Chukun Pan
4825defe44
uboot-envtools: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-25 23:16:35 +01:00
Nicolò Veronese
2a0805fd3d uboot-envtools: add support for Zyxel EX5601-T0 ubootmod
The ubootmod bootlaoder for EX5601-T0 uses two partitions
 in ubi to store enviroment variables. so proper config
 is needed.

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2023-11-25 14:51:21 +01:00
Valerio 'ftp21' Mancini
a9cf87027e uboot-mediatek: add initial Zyxel EX5601-T0 support
Flash procedure is described in next commit.

TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
 volumes to boot openwrt.

mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip

Changelist:
 - Added profile for 4k+256 SPI NAND_TYPE
 - Added basic Zyxel EX5601-T0 uboot profile

Backported from hitech95 branch:
 - Button RESET pin fix
 - Button WPS pin fix

Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2023-11-25 14:51:21 +01:00
Daniel Golle
c8c2f52262 mediatek: add support for Zbtlink ZBT-Z8102AX
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-24 21:28:35 +00:00
Daniel Golle
2634d3f855 uboot-envtools: add settings for Synology DS213j
Add settings to be able to access the U-Boot environment on the
Synology DS213j NAS.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-20 13:40:17 +00:00
Carter Wang
df4c5f7eb2 uboot-mediatek: Fix ubi command in uboot commands
Fix typo 'ubi remote ...' -> 'ubi remove ...'.

Signed-off-by: Carter Wang <carter.wang@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-19 22:08:23 +00:00
Chukun Pan
b42c527228 uboot-mediatek: add JCG Q30 PRO support
The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-11-19 16:52:16 +01:00
Daniel Golle
d6a06acaa5 arm-trusted-firmware-mediatek: update to release 2023-10-13
Drop local patches now upstream.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-09 00:34:38 +00:00
Daniel Golle
f8414f1a6f uboot-envtools: add environment config for MeiG SLT866
Add configuration to access U-Boot environment on MeiG SLT866.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-11-03 21:16:29 +00:00
Petr Štetiar
bc47613cf0
Revert "uboot-sunxi: add missing type __u64"
This reverts commit 3cc57ba462 as it
should be fixed in commit 78cbd5a57e11 ("tools: macOS: types.h: fix
missing unsigned types").

References: #13833
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-11-02 20:20:56 +01:00
Petr Štetiar
f691830307
Revert "uboot-mediatek: fix build on Mac OS X"
This reverts commit 997ff740dc.
78cbd5apick as it should be fixed in commit 78cbd5a57e11 ("tools: macOS:
types.h: fix missing unsigned types").

References: #13833
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-11-02 20:20:56 +01:00
Jianhui Zhao
3bbc1d5fba uboot-mediatek: fix determine the size of an uImage.FIT using 'imsz' or 'imszb'.
It must read the entire image for previous code of 'imsz' or 'imszb'.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
2023-10-31 22:12:30 +00:00
Weiping Yang
c7baca3bb6 ath79: add support for GL.iNet GL-S200
Specifications:
SoC: QCA9531(650MHz)
RAM: DDR2 128M
Flash: SPI NOR 16M + SPI NAND 128M
WiFi: 2.4GHz with 2 antennas(WiFi/Thread)
Ethernet:
    1xLAN(10/100M)
    2xWAN(10/100M)
Button: 1x Reset Button
Switch: 1x Mode switch
LED: 1x Blue LED + 1x White LED + 1x Orange LED
IOT: Thread + ZigBee/Zwave

By uboot web failsafe:
Push the reset button for 5 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2023-10-31 13:53:11 +01:00
Milan Krstic
17465fc77e ramips: add support for ZyXEL LTE5398-M904
ZyXEL LTE5398-M904 is a dual band 802.11ac indoor LTE/3G CPE with an FXS
port.

Specifications:

* SoC: Mediatek MT7621AT
* RAM: 256 MB
* Flash: 128MB NAND (MX30LF1G18AC)
* WiFi: MediaTek MT7603 2.4G + MediaTek MT7615 5G
* Switch: 2 GbE ports MT7530
* LTE/3G: Quectel EG18-EA LTE-A Cat. 18
* SIM: 1 micro-SIM card slot
* Buttons: Reset, WPS
* LEDs: power (G/B), internet (G), LTE (R/G/Orange), WiFi (G), voice (G)
* VoIP: 1 FXS RJ11 port
* Power: 12V, 2A

UART serial console:

57600,8N1
Unpopulated header J5:

 [o] GND
 [ ] key - no pin
 [o] RX
 [o] TX
 [o] 3.3V Vcc

Installation:

* Log in as root using ssh to 192.168.1.1
* scp OpenWrt initramfs-recovery.bin image to root@192.168.1.1:/tmp/
* Prepare bootloader config by running:
   nvram setro uboot DebugFlag 0x1
   nvram setro uboot CheckBypass 0
   nvram commit
* Run "mtd_write -w write /tmp/initramfs-recovery.bin Kernel" and reboot
* Wait for OpenWrt to boot and ssh to root@192.168.1.1
* Run sysupgrade with OpenWrt squashfs-sysupgrade.bin image

For mode details about flashing see:
2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19)

Unsupported:

* FXS/Voice

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2023-10-29 18:51:11 +01:00
Furong Xu
03987d2d11 uboot-mediatek: Sync phy-mode for Xiaomi Redmi Router AX6000
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.

Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
2023-10-28 23:25:31 +02:00
Kristian Skramstad
5e33fdfc47 qualcommax: ipq807x: add support for Netgear WAX630
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
  GND RXD TXD, beginning from the external antennas. 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet

Wlan:
* 4x4 in 2.4GHz  : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)

Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A

Mounting: Wall and ceiling
```

```
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to the console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-10-28 19:49:18 +02:00
Tianling Shen
423186d7d8 mediatek: add CMCC RAX3000M support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Tianling Shen
fddd735dd5 uboot-mediatek: add support for CMCC RAX3000M
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Tianling Shen
7d8ffe941d arm-trusted-firmware-mediatek: add emmc/spim-nand ddr4 build for mt7981
They will be used on CMCC RAX3000M.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2023-10-28 19:05:07 +02:00
Nicolò Veronese
8849ccb995 uboot-mediatek: fix global pll clock override on mtk_spim
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
 a new system to calculate the SPI clocks has been added.

Unfortunately, the do_div macro overrides the global
 priv->pll_clk_rate field. This will cause to have a reduced
 clock rate on each subsequent SPI call.

Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
2023-10-22 18:14:03 +02:00
Josua Mayer
71e2c64bef uboot-mvebu: armada 388 clearfog: support additional ddr configurations
Fixes Issue #13632.

Patches as submitted in v1 to u-boot mailinglist:
https://lists.denx.de/pipermail/u-boot/2023-October/533148.html

Signed-off-by: Josua Mayer <josua@solid-run.com>
2023-10-22 10:52:40 +02:00
Jianhui Zhao
4536fb4c5c uboot-mediatek: fix typo in bootmenu for GL-MT6000
Fixes: fe10f97 ("filogic: add support for GL.iNet GL-MT6000")

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2023-10-20 18:13:57 +02:00
Linus Walleij
9340babdcb
boot/apex: Restore the APEX boot loader
This is a partial revert of the deletion of the IXP4xx
target: we restore the APEX boot loader so we can use it
for the NSLU2 and related targets.

The APEX upstream is as dead as it gets so I have applied
OpenWrts old patches on top of the never released
v1.6.10 version and forked it into an OpenWrt variant
on GitHub. If the upstream comes back alive I will
happily switch over to it.

The file refers to the external GitHub, I suppose when
integrating this patch the file should be copied to OpenWrts
file repository and the file link changed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2023-10-20 13:26:45 +02:00
Glen Lee
3aef61060e
ipq806x: add support for Extreme Networks AP3935
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/

SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
       NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
        4pin Serial Header | 3.3 | GND | RX | TX

MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env

 * Installation via either RJ45 console or on-board 4 PIN header

Install Method
--------------
1) Setup TFTP server, and place
     openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
     in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
     your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
     (use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
     set bootcmd 'ping 192.168.1.1; run boot_flash'
     saveenv
8) TFTP image to RAM:
     tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
     In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
     image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin

Signed-off-by: Glen Lee <g2lee@yahoo.com>
2023-10-05 00:56:57 +02:00
Jianhui Zhao
fe10f97439 filogic: add support for GL.iNet GL-MT6000
Hardware specification:
* SoC: MediaTek MT7986A 4x A53
* Flash: 8GB EMMC
* RAM: 1GB DDR4
* Ethernet:
  * 2x2.5G RJ45 port (RTL8221B)
  * 4x1G RJ45 ports (MT7531AE)
* WLAN:
  * 2.4GHz: MT7976GN 4T4R
  * 5GHz: MT7976AN 4T4R
* Button: Reset
* LED: 1 x dual color LED
* USB: 1 x USB 3.0
* Power: DC 12V 4A
* UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC)
* JTAG: 9 PIN

If you want to use u-boot from OpenWrt, you can upgrade it safely.
* bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin
* fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip

`openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
2023-09-29 00:18:26 +01:00
Chukun Pan
eb273ef640 uboot-mediatek: sync spi-nand driver with SDK
When adding new router support, I found that uboot
could not recognize flash: "unknown raw ID xxx".

Sync SPI-NAND driver for mediatek to fixes this:
 * Add support for Winbond W25N01KV 1Gbit chip.
 * Add support for Etron SPI-NAND chip.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2023-09-29 00:07:50 +01:00
Hauke Mehrtens
d2b5f4b2cd treewide: Add extra CPE identifier
This adds some Common Platform Enumerations (CPE) identifiers which I
found.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-09-25 23:06:33 +02:00
Elbert Mai
75ee5546e9 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+)
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2023-09-24 17:16:16 +02:00
Sebastian Pflieger
03123a3ae5 arm-trusted-firmware-sunxi: update to version 2.9
- detect die revision used in variants of the Allwinner H616 SoC (H313, T507)
- support for H6 boards without PMIC

Tested on Pine64+ and Orange PI Zero2

Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
2023-09-24 17:12:24 +02:00
Kristian Skramstad
76e419288f ipq807x: add support for Netgear WAX620
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
  Use the header closest to LED 4 and 5.
  They are marked with a white stroke.
  TX RX GND, beginning from "4". 115200n8.

Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)

Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)

Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```

```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1.  Download the OpenWrt initramfs image. Copy the image to a TFTP server
2.  Connect to console on the AP, and connect the LAN port to your LAN
3.  Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4.  Set active_fw in env
    # setenv active_fw 1
5.  Transfer the initramfs image with TFTP
    # setenv serverip 192.168.1.10 (IP of TFTP server host)
    # setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
    # tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6.  Reboot and load the image
    # bootm
7.  SCP factory image to the AP
    # scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8.  Connect to device using SSH (use the LAN port)
9.  Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
    Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
    # cat /proc/mtd (To check MTD partitions)
    # ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
    # /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
    # reboot
```

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2023-09-24 13:09:16 +02:00
Daniel Golle
8428bed15d uboot-mediatek: add build for mt7981 rfb
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-21 10:15:08 +01:00
Daniel Golle
be6e257fe6 arm-trusted-firmware-mediatek: fix copy&paste error in Makefile
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.

Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-21 10:15:08 +01:00
Robert Marko
2bb418299d
uboot-mvebu: eDPU: add support for version with external switch
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.

In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-09-19 12:12:17 +02:00
Zoltan HERPAI
6bf8193b25 sunxi: add support for Bananapi P2 Zero
CPU:     Allwinner H2+ quad-core Cortex-A7 @ 1.2GHz
Memory:  512Mb DDR3
Storage: SDcard, 8GB eMMC
Network: 10/100M ethernet, optional PoE support, Ampak AP6212 wifi + BT
USB:     1x USB 2.0 OTG
Other:   40-pin expansion header, mini-HDMI

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 18:15:21 +02:00
Zoltan HERPAI
12584395dc sunxi: add support for H616 SoC and Orangepi Zero 2
Specifications:

SoC:     Allwinner H616 @ 1.5 Ghz
DRAM:    1Gb LPDDR3
Power:   5V USB-C
Video:   HDMI (Type 2.0A - micro)
Network: 10/100/1000Mbps Ethernet (Realtek RTL8211F), AW859A BT+wifi
Storage: microSD / 2Mb SPI flash
USB:     1 USB2.0 Host
Debug    Serial UART

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-09-18 00:08:19 +02:00
Piotr Dymacz
69f12c2f23 uboot-envtools: ramips: add support for ALFA Network AX1800RM
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2023-09-11 11:46:52 +02:00
Daniel Golle
948ad2ec7a arm-trusted-firmware-mediatek: fix hang on reboot on MT7622
With recent updates of TF-A the previously already fixed bug slipped
back into the source tree. Again, reorder bl2 init for MT7622 and
initialize WDT only after DRAM init has completed to avoid the
notorious hang.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-10 23:47:38 +01:00
Daniel Golle
9725524235 uboot-mediatek: sync mtk-snand driver with SDK
Sync SPI-NAND/ECC controller driver for MT7622, MT7981, MT7986 and MT7988:
 * Platform data for MT7981 was actually missing and is now added.
 * Add support for Winbond W25N01KV 1Gbit chip.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-09-10 23:46:06 +01:00
Patricia Lee
907e9e0bd3 mediatek: add support for Cetron CT3003
**Hardware specification:**

- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
  | Layout:   |
  | :-------- |
  | <Antenna> |
  | VCC       |
  | GND       |
  | Tx        |
  | Rx        |

**Flash instructions:**

1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.

**Notes:**

If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.

Signed-off-by: Patricia Lee <patricialee320@gmail.com>
2023-09-08 23:17:26 +02:00
Jayantajit Gogoi
18b6bae851 uboot-rockchip: add suport for Radxa ROCK Pi E
Add uboot support for Radxa ROCK Pi E, rockchip rk3328 board.
Add pre-built files to fix swig dependencies.

Specification:

- CPU: Rockchip RK3328 64-bit Quad-core
- RAM: DDR3 256MB ~ 2GB
- Network:
    1 x 10/100/1000M Ethernet
    1 x 10/100M Ethernet
- USB Host:
    1 x USB3.0 Type A HOST
    1 x USB2.0 OTG (40-pin pin-header)
- Wireless:
    RTL8723DU/RTL8821CU
- Power Supply: Type-C 5V

Installation:
- Write image to SD Card or EMMC with dd
- Boot ROCK Pi E from the SD Card

Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
2023-09-05 00:20:51 +05:30
Daniel Golle
33046d2a47 arm-trusted-firmware-mediatek: enable built-in 2.5G PHY on MT7988
Always enable built-in 2.5G PHY on MT7988 for now, so that it can be
used. In future it would be nice to be able to switch power and MDIO
access via address 0 at run-time in Linux, both, to be able to use
external PHYs at address 0 and to reduce power consumption on systems
not using the built-in 2.5G PHY.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 23:44:52 +01:00
Daniel Golle
78e3adcaf9 uboot-mediatek: fix dependency on TF-A for MT7988 RFB (sdmmc)
The U-Boot build for the MT7988 reference board booting from SD card
wrongly depended on the 'ddr4' variant of the ARM TrustedFirmware-A build
even though the 'comb' variant is used. Fix that dependency.

Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 23:43:49 +01:00
Daniel Golle
fff4441135 uboot-mediatek: add builds for UniFi 6 LR v2 and v3
While the v2 is nearly identical to v1, v3 uses a different PHY and
needs a different build for Ethernet to work in U-Boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Daniel Golle
1d5778e18d uboot-mediatek: build fully-featured U-Boot for MT7988 RFB
Select many potentially useful options for the MT7988 RFB U-Boot builds.
The resulting loader is intended as a development tool and intends to be
generic. It does *not* have a default bootcmd set, but allows to boot
pretty much everything, including EFI executables.

To install this U-Boot build to the eMMC:
  opkg install mmc-utils partx-utils
  mmc bootpart enable 1 1 /dev/mmcblk0
  echo 0 > /sys/block/mmcblk0boot0/force_ro
  dd if=*mediatek_mt7988a-rfb-nand-emmc-preloader.bin of=/dev/mmcblk0boot0
  dd if=*mediatek_mt7988a-rfb-nand-emmc-gpt.bin of=/dev/mmcblk0
  partx -a /dev/mmcblk0
  dd if=*mediatek_mt7988a-rfb-nand-emmc-bl31-uboot.fip of=/dev/mmcblk0p3

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-28 16:35:22 +01:00
Antonio Flores
c0c4efe6f1 uboot-rockchip: fix swig dependency for ROCK64
Pre build files to fix swig dependency.

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2023-08-27 19:20:11 +02:00
Antonio Flores
0405e11a71 uboot-rockchip: add support for PINE64 ROCK64
Add uboot support for PINE64 ROCK64, rockchip rk3328 board.

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2023-08-27 19:20:11 +02:00
Zoltan HERPAI
53c2f174ad uboot-sunxi: bump to 2023.04
Compile-tested: all boards
Runtime-tested:
 - Cortex-A8: pcDuino
 - Cortex-A7: Bananapro, Bananapi M3
 - Cortex-A53:Pine64+

Notes:
 - binman tries to add firmware for the SCP (system control processor), which
   we don't build, and is optional for the boot process on 64-bit. Disable this
   via setting the SCP envvar to /dev/null. For further info, see [1] .

[1] https://github.com/u-boot/u-boot/blob/master/board/sunxi/README.sunxi64

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2023-08-26 15:04:16 +02:00
Robert Marko
67dacdd652 arm-trusted-firmware-mvebu: bump to v2.9
We are using the outdated 2.7 TF-A, so lets update to current v2.9 version.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-26 00:11:48 +02:00
Robert Marko
f6ca36df84 arm-trusted-firmware-mvebu: update CM3 GCC to 12.3rel1
We are using the outdated 11.2 GCC for CM3, lets update to the current
12.3rel1 version from ARM [1].

[1] https://developer.arm.com/downloads/-/arm-gnu-toolchain-downloads

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-26 00:11:48 +02:00
Robert Marko
84e9d49452 arm-trusted-firmware-mvebu: bump cryptopp to version 8.8
We are using the outdated Crypto++ version 8.5, so lets update to the
current version 8.8.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-26 00:11:48 +02:00
Robert Marko
ef82e26d35 arm-trusted-firmware-mvebu: bump mox-boot-builder to current version
We have to move to use git clone as there are no newer tagged releases.

Changes:
604f8f5 Default CROSS_CM3 to arm-none-eabi- instead of armv7m-softfloat-eabi-
b9b9419 Tidy up license information
0290b2c wtmi: Fix typo
a10b8e9 Makefile: fix a53-firmware.bin generation (maximum size is not optimal)
f654082 wtmi: Add const qualifier to isr_vector
4a43a3b wtmi: Improve detection of ESPRESSObin boards with Topaz
189e629 wtmi: Improve detection of boards with insufficient MDIO pull-up
3dac4fe wtmi: Fix detection of Armada 3720 Devel Board
3ca4dfa Bump mox-imager commit

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-26 00:11:48 +02:00
Robert Marko
ff671d318c arm-trusted-firmware-mvebu: bump mv-ddr-marvell to current version
Changes:
1de442d Convert floating point operations to integer operations
ce6770d Modify mv_ddr4_calibration_validate function body to match function header

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-26 00:11:48 +02:00
Robert Marko
ebbcfd095d arm-trusted-firmware-mvebu: bump a3700-utils to current version
Changes:
a3e1c67 wtmi: Fix linker output sections
f65e3bf wtmi: Remove usage of non-existant string.h file and memcpy() function

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-26 00:11:48 +02:00
Robert Marko
96727397ef uboot-envtools: fix parallel building
Recent envtools update to 2023.07.02 has introduced a breakage when trying
to parallel build with the following error:
/bin/sh: line 1: scripts/basic/fixdep: No such file or directory

Luckily it can easily be reproduced locally via a simple script so it was
not hard to bisect it down to upstream commit [1].

However, its not that commits fault, it just uncovered an issue with the
way we have been building envtools for a long time, maybe even from the
package introduction.

The issue is that we are trying to build envtools as one of the U-Boot
no-dot-config-targets but envtools was newer a valid target for it but
since we were creating the config headers that were not actually used it
was actually building all this time.

Since the blamed commit [1] a tool called printinitialenv is built and
now a proper config is actually required in order for prerequisites to
get built properly.

So, in order to properly fix this (Hopefully for good) lets stop pretending
that envtools are a valid no-dot-config-targets target and use the
tools-only defconfig which is meant exactly for just building the tools.
This will make a minimal config for the U-Boot sandbox target and then
envtools will build just fine in parallel mode (I tested with 32 threads).
We do hovewer need to override the ARCH passed by OpenWrt and set it to
sandbox as otherwise U-Boot will not find the required headers because the
ARCH is being overriden to an incorrect one.

[1] 40b77f2a3a

Fixes: 9db0330052 ("uboot-envtools: update to 2023.07.02")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2023-08-25 23:38:11 +02:00
Daniel Golle
ff2379662c uboot-mediatek: increase max. memory regions on mt7988-rfb
WED requires a bunch of additional reserved memory regions. As U-Boot's
LMB allocator defaults to a maximum of only 8 regions, this currently
makes using WED impossible.
Raise LMB_MAX_REGIONS to 64 just like for all other MediaTek boards
with a SoC supporting WED.

Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-08-24 18:49:49 +01:00