Commit Graph

1200 Commits

Author SHA1 Message Date
Denis Kalashnikov
695a1cd53c ath79: add support for MikroTik RouterBOARD 912UAG-2HPnD
This board has been supported in the ar71xx.

Links:
* https://mikrotik.com/product/RB912UAG-2HPnD
* https://openwrt.org/toh/hwdata/mikrotik/mikrotik_rb912uag-2hpnd

This also supports the 5GHz flavour of the board.

Hardware:
* SoC: Atheros AR9342,
* RAM: DDR 64MB,
* SPI NOR: 64KB,
* NAND: 128MB,
* Ethernet: x1 10/100/1000 port with passive POE in,
* Wi-Fi: 802.11 b/g/n,
* PCIe,
* USB: 2.0 EHCI controller, connected to mPCIe slot and a Type-A
  port -- both can be used for LTE modem, but only one can be
  used at any time.
* LEDs: 5 general purpose LEDs (led1..led5), power LED, user LED,
  Ethernet phy LED,
* Button,
* Beeper.

Not working:
* Button: it shares gpio line 15 with NAND ALE and NAND IO7,
  and current drivers doesn't easily support this configuration,
* Beeper: it is connected to bit 5 of a serial shift register
  (tested with sysfs led trigger timer). But kmod-gpio-beeper
  doesn't work -- we left this as is for now.

Flashing:
* Use the RouterBOARD Reset button to enable TFTP netboot,
boot kernel and initramfs and then perform sysupgrade.
* From ar71xx OpenWrt firmware run:
  $ sysupgrade -F /tmp/<sysupgrade.bin>
For more info see: https://openwrt.org/toh/mikrotik/common.

Co-Developed-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
2021-06-21 10:48:27 +02:00
Denis Kalashnikov
820e660cd7 ath79: add NAND driver for MikroTik RB91xG series
Main part is copied from ar71xx original driver rb91x_nand
written by Gabor Juhos <juhosg@openwrt.org>.

What is done:
* Support of kernel 5.4 and 5.10,
* DTS support,
* New gpio API (gpiod_*) support.

Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
2021-06-21 10:48:27 +02:00
Denis Kalashnikov
7b8931678c ath79: add gpio-latch driver for MikroTik RouterBOARDs
This is a slighty modified version of ar71xx gpio-latch driver
written by Gabor Juhos <juhosg@openwrt.org>.

Changes:
* DTS support,
* New gpio API (gpiod_*).

Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
2021-06-21 10:48:27 +02:00
Rui Salvaterra
677813c776 kernel: bump 5.10 to 5.10.43
No deleted or manually refreshed patches.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-06-14 01:36:36 +02:00
Andy Lee
c5235f6b24 ath79: add support for TP-Link TL-WR841HP v3
Specifications:
- QCA9533 SoC, 8 MB nor flash, 64 MB DDR2 RAM
- 2x2 9dBi antenna, wifi 2.4Ghz 300Mbps
- 4x Ethernet LAN 10/100, 1x Ethernet WAN 10/100
- 1x WAN, LAN, Wifi, PWR, WPS, RE Leds
- Reset, Wifi on/off, WPS, RE buttons
- Serial UART at J4 onboard: 3.3v GND RX TX, 1152008N1

Label MAC addresses based on vendor firmware:
LAN      *:ea    label
WAN      *:eb    label +1
2.4 GHz  *:ea    label
The label MAC address in found in u-boot 0x1fc00

Installation:
Upload openwrt-ath79-generic-tplink_tl-wr841hp-v3-squashfs-factory.bin
from stock firmware webgui.
Maybe we need rename to shorten file name due to stock webgui error.

Revert back to stock firmware instructions:
- set your PC to static IP address 192.168.0.66 netmask 255.255.255.0
- download stock firmware from Tp-link website
- put it in the root directory of tftp server software
- rename it to wr841hpv3_tp_recovery.bin
- power on while pressing Reset button until any Led is lighting up
- wait for the router to reboot. done

Forum support topic:
https://forum.openwrt.org/t/support-for-tp-link-tl-wr841hp-v3-router

Signed-off-by: Andy Lee <congquynh284@yahoo.com>
[rebase and squash]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-13 23:30:05 +02:00
Jonathan A. Kollasch
f36990eae7 ath79: fix eth0 PLL registers on WD My Net Wi-Fi Range Extender
This replaces the register bits for RGMII delay on the MAC side in favor
of having the RGMII delay on the PHY side by setting the phy-mode
property to rgmii-id (RGMII internal delay), which is supported by the
at803x driver.  Speed 1000 is fixed as a result, so now all ethernet
speeds function.

Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Reviewed-by: Michael Pratt <mcpratt@pm.me>
2021-06-07 00:25:11 +02:00
Nick Hainke
3e0387b3db ath79: Support for Ubiquiti Rocket 5AC Lite
The Ubiquiti Rocket 5AC Lite (R5AC-Lite) is an outdoor router.

Specifications:
 - SoC: Qualcomm Atheros QCA9558
 - RAM: 128 MB
 - Flash: 16 MB SPI
 - Ethernet: 1x 10/100/1000 Mbps
 - WiFi 5 GHz: QCA988x
 - Buttons: 1x (reset)
 - LEDs: 1x power, 1x Ethernet, 4x RSSI

Installation:
- Instructions for XC-type Ubiquiti:
  https://openwrt.org/toh/ubiquiti/common

Signed-off-by: Nick Hainke <vincent@systemli.org>
2021-06-07 00:23:51 +02:00
INAGAKI Hiroshi
a4e2766a5b ath79: add support for NEC Aterm WF1200CR
NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9561.

Specification:

- SoC		: Qualcomm Atheros QCA9561
- RAM		: DDR2 128 MiB (W971GG6SB-25)
- Flash		: SPI-NOR 8 MiB (MX25L6433FM2I-08G)
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9561 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100 Mbps
  - Switch	: QCA9561 (SoC)
- LEDs/Keys	: 8x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from "JP1" marking
  - 115200n8
- Power		: 12 VDC, 0.9 A

Flash instruction using factory image (stock: < v1.3.2):

1. Boot WF1200CR normally with "Router" mode
2. Access to "http://192.168.10.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button to
   perform firmware update
4. Wait ~150 seconds to complete flashing

Alternate flash instruction using initramfs image (stock: >= v1.3.2):

1. Prepare the TFTP server with the IP address 192.168.1.10 and place
   the OpenWrt initramfs image to the TFTP directory with the name
   "0101A8C0.img"
2. Connect serial console to WF1200CR
3. Boot WF1200CR and interrupt with any key after the message
   "Hit any key to stop autoboot:  2", the U-Boot starts telnetd after
   the message "starting telnetd server from server 192.168.1.1"
4. login the telnet (address: 192.168.1.1)
5. Perform the following commands to modify "bootcmd" variable
   temporary and check the value
   (to ignore the limitation of available commands, "tp; " command at
   the first is required as dummy, and the output of "printenv" is
   printed on the serial console)

   tp; set bootcmd 'set autostart yes; tftpboot'
   tp; printenv

6. Save the modified variable with the following command and reset
   device

   tp; saveenv
   tp; reset

7. The U-Boot downloads initramfs image from TFTP server and boots it
8. On initramfs image, download the sysupgrade image to the device and
   perform the following commands to erase stock firmware and sysupgrade

   mtd erase firmware
   sysupgrade <sysupgrade image>

9. After the rebooting by completion of sysupgrade, start U-Boot telnetd
   and login with the same way above (3, 4)
10. Perform the following commands to reset "bootcmd" variable to the
    default and reset the device

    tp; run seattle
    tp; reset

    (the contents of "seattle":
     setenv bootcmd 'bootm 0x9f070040' && saveenv)
11. Wait booting-up the device

Known issues:

- the following 6x LEDs are connected to the gpio controller on QCA9888
  chip and the implementation of control via the controller is missing in
  ath10k/ath10k-ct

  - "ACTIVE" (Red/Green)
  - "2.4GHz" (Red/Green)
  - "5GHz"   (Red/Green)

Note:

- after the version v1.3.2 of stock firmware, "offline update" by
  uploading image by user is deleted and the factory image cannot be
  used

- the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN
  and the configuration is required on OpenWrt

  - gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output
  - pinmux: set GPIO 14/19 as switch-controlled LEDs

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-06-06 21:21:51 +02:00
Felix Matouschek
624b85e646 ath79: add support for Devolo dLAN pro 1200+ WiFi ac
This patch adds support for the Devolo dLAN pro 1200+ WiFi ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet ports,
has a QCA7500 PLC and uses the HomePlug AV2 standard.

Other than the PLC the hardware is identical to the Devolo Magic 2 WIFI.
Therefore it uses the same dts, which was moved to a dtsi to be included
by both boards.

This is a board that was previously included in the ar71xx tree.

Hardware:
   SoC:         AR9344
   CPU:         560 MHz
   Flash:       16 MiB (W25Q128JVSIQ)
   RAM:         128 MiB DDR2
   Ethernet:    2xLAN 10/100/1000
   PLC:         QCA75000 (Qualcomm HPAV2)
   PLC Uplink:  1Gbps MIMO
   PLC Link:    RGMII 1Gbps (WAN)
   WiFi:        Atheros AR9340 2.4GHz 802.11bgn
                Atheros AR9882-BR4A 5GHz 802.11ac
   Switch:      QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
   Button:      3x Buttons (Reset, wifi and plc)
   LED:         3x Leds (wifi, plc white, plc red)
   GPIO Switch: 11-PLC Pairing (Active Low)
                13-PLC Enable
                21-WLAN power

MACs Details verified with the stock firmware:
   Radio1: 2.4 GHz &wmac     *:4c Art location: 0x1002
   Radio0: 5.0 GHz &pcie     *:4d Art location: 0x5006
   Ethernet        &ethernet *:4e = 2.4 GHz + 2
   PLC uplink      ---       *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink

The Powerline (PLC) interface of the dLAN pro 1200+ WiFi ac requires 3rd
party firmware which is not available from standard OpenWrt package
feeds. There is a package feed on github which you must add to
OpenWrt buildroot so you can build a firmware image which supports the
plc interface.

See: https://github.com/0xFelix/dlan-openwrt (forked from Devolo and
added compatibility for OpenWrt 21.02)

Flash instruction (TFTP):
 1. Set PC to fixed ip address 192.168.0.100
 2. Download the sysupgrade image and rename it to uploadfile
 3. Start a tftp server with the image file in its root directory
 4. Turn off the router
 5. Press and hold Reset button
 6. Turn on router with the reset button pressed and wait ~15 seconds
 7. Release the reset button and after a short time
    the firmware should be transferred from the tftp server
 8. Allow 1-2 minutes for the first boot.

Signed-off-by: Felix Matouschek <felix@matouschek.org>
[add "plus" to compatible and device name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-06 18:56:45 +02:00
John Audia
752cd29904 kernel: bump 5.4 to 5.4.124
Manually rebased:
  generic/hack-5.4/662-remove_pfifo_fast.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[manual changes to ramips/patches-5.10/835-asoc-add-mt7620-support.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-06-06 00:25:25 +02:00
Rui Salvaterra
da77b9c2f1 kernel: bump 5.10 to 5.10.42
Deleted (reverse-appliable):
generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch

Manually refreshed:
ramips/patches-5.10/835-asoc-add-mt7620-support.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-06-06 00:24:07 +02:00
Adrian Schmutzler
6f648ed7e6 treewide: remove "+" sign for increment with macaddr_add
Many people appear to use an unneeded "+" prefix for the increment
when calculating a MAC address with macaddr_add. Since this is not
required and used inconsistently [*], just remove it.

[*] As a funny side-fact, copy-pasting has led to almost all
    hotplug.d files using the "+", while nearly all of the
    02_network files are not using it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:54:37 +02:00
Michael Pratt
7b9a0c264c ath79: use dynamic partitioning for TP-Link CPE series
CPExxx and WBSxxx boards with AR9344 SOC
use the OKLI lzma kernel loader
with the offset of 3 blocks of length 4k (0x3000)
in order to have a fake "kernel" that cannot grow larger
than how it is defined in the now static OEM partition table.

Before recent changes to the mtdsplit driver,
the uImage parser for OKLI only supported images
that started exactly on an eraseblock boundary.

The mtdsplit parser for uImage now supports identifying images
with any magic number value
and at any offset from the eraseblock boundary
using DTS properties to define those values.

So, it is no longer necessary to use fixed sizes
for kernel and rootfs

Tested-by: Andrew Cameron <apcameron@softhome.net>  [CPE510 v2]
Tested-by: Bernhard Geier <freifunk@geierb.de>      [WBS210 v2]
Tested-by: Petrov <d7c48mWsPKx67w2@gmail.com>       [CPE210 v1]
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-05 23:39:14 +02:00
Zoltan HERPAI
1eb481206d ath79: add support for Qualcomm AP143 reference boards
Specifications:

SoC:    QCA9533
DRAM:   32Mb DDR1
Flash:  8/16Mb SPI-NOR
LAN:    4x 10/100Mbps via AR8229 switch (integrated into SoC)
        on GMII
WAN:    1x 10/100Mbps via MII
WLAN:   QCA9530
USB:    1x 2.0
UART:   standard QCA UART header
JTAG:   yes
Button: 1x WPS, 1x reset
LEDs:   8x LEDs

A version with 4Mb flash is also available, but due to lack of
enough space it's not supported.

As the original flash layout does not provide enough space for
the kernel (1472k), the firmware uses OKLI and concat flash to
overcome the limitation without changing the boot address of the
bootloaders.

Installation:

1. Original bootloader

  Connect the board to ethernet
  Set up a server with an IP address of 192.168.1.10
  Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
  available via TFTP

  tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
  erase 0x9f050000 +$filesize
  cp.b $fileaddr 0x9f050000 $filesize

  Reboot the board.

2. pepe2k's u-boot_mod

  Connect the board to ethernet
  Set up a server with an IP address of 192.168.1.10
  Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin
  available via TFTP, as "firmware.bin"

  run fw_upg

  Reboot the board.

For the 16M version of the board, please use
openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE,
set up IMAGE/factory.bin without metadata]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 01:17:11 +02:00
Sven Eckelmann
9a172797e5 ath79: Add support for OpenMesh A40
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
  - eth0
    + Label: Ethernet 1
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as WAN interface
  - eth1
    + Label: Ethernet 2
    + AR8035 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + used as LAN interface
* 1x USB
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-06-05 01:17:11 +02:00
Sven Eckelmann
eaf2e32c12 ath79: Add support for OpenMesh A60
Device specifications:
======================

* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
  - 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
  - eth0
    + Label: Ethernet 1
    + AR8035 ethernet PHY (RGMII)
    + 10/100/1000 Mbps Ethernet
    + 802.3af POE
    + used as WAN interface
  - eth1
    + Label: Ethernet 2
    + AR8031 ethernet PHY (SGMII)
    + 10/100/1000 Mbps Ethernet
    + used as LAN interface
* 1x USB
* internal antennas

Flashing instructions:
======================

Various methods can be used to install the actual image on the flash.
Two easy ones are:

ap51-flash
----------

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.

initramfs from TFTP
-------------------

The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):

   setenv serverip 192.168.1.21
   setenv ipaddr 192.168.1.1
   tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr

The actual sysupgrade image can then be transferred (on the LAN port) to the
device via

  scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/

On the device, the sysupgrade must then be started using

  sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-06-05 01:17:11 +02:00
David Bauer
862bc9f597 ath79: add missing v5.4 SPI chipselect patch
The patch was not applied to the v5.4 target, thus breaking Kernel 5.4
on devices with multiple flash chips attache to the SPI bus.

Fixes commit bd54e73954 ("ath79: set number of chipselect lines")

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-26 23:11:00 +02:00
John Audia
3e1c92f9e1 kernel: bump 5.4 to 5.4.118
Manually rebased:
  ath79/patches-5.4/0033-spi-ath79-drop-pdata-support.patch

Removed uneeded patch:
  ath79/patches-5.4/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-05-23 15:09:06 +02:00
Giulio Lorenzo
b108ed0ab0 ath79: add support for ZiKing CPE46B
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b

Specifications:

- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging

Flashing instruction:

You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.

Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-17 01:01:32 +02:00
Adrian Schmutzler
3dd9f82fec ath79: fix leading whitespaces in generic 01_leds
Use tabs consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-17 01:01:32 +02:00
Joao Henrique Albuquerque
4f07966696 ath79: add support for COMFAST CF-E375AC
COMFAST CF-E375AC is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9563 + QCA9886 + QCA8337.

Short specification:

    2x 10/100/1000 Mbps Ethernet, with PoE support
    128MB of RAM (DDR2)
    16 MB of FLASH
    3T3R 2.4 GHz, 802.11b/g/n
    2T2R 5 GHz, 802.11ac/n/a, wave 2
    built-in 5x 3 dBi antennas
    output power (max): 500 mW (27 dBm)
    1x RGB LED, 1x button
    built-in watchdog chipset

Flash instruction:
1) Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.

2) TFTP
2.1) Set a tftp server on your machine with a fixed IP address of
     192.168.1.10. A place the sysupgrade as firmware_auto.bin.
2.2) boot the device with an ethernet connection on fixed ip route
2.3) wait a few seconds and try to login via ssh

3) TFTP trough Bootloader
3.1) open the device case and get a uart connection working
3.2) stop the autoboot process and test connection with serverip
3.3) name the sysupgrade image firmware.bin and run firmware_upg

MAC addresses:
Though the OEM firmware has four adresses in the usual locations,
it appears that the assigned addresses are just incremented in a
different way:

interface    address    location
LAN:          *:DC      0x0
WAN           *:DD      0x1002
WLAN 2.4g     *:E6      n/a (0x0 + 10)
WLAN 5g       *:DE      0x6
unused        *:DF      0x5006

The MAC address pointed at the label is the one assign to the LAN
interface.

Signed-off-by: Joao Henrique Albuquerque <joaohccalbu@gmail.com>
[add label-mac-device, remove redundant uart status, fix whitespace
issues, fix commit message wrapping, remove x bit on DTS file]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-17 01:01:32 +02:00
Michael Pratt
bf8c16dfa2 ath79: set lzma-loader variables to null by default
This fixes a small regression where the lzma-loader variable values
are being shared between boards that require different configurations.

If not set to "" globally, a device without these settings will just take
the last values another device has set before in the queue.

Fixes: 1b8bd17c2d ("ath79: lzma-loader: allow setting custom kernel magic")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[add detailed explanation to the commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-16 13:05:42 +02:00
Rui Salvaterra
d337731f85 kernel: bump 5.10 to 5.10.37
Automatically refreshed:
ath79/patches-5.10/0032-MIPS-ath79-sanitize-symbols.patch
bcm63xx/patches-5.10/322-MIPS-BCM63XX-switch-to-IRQ_DOMAIN.patch
bcm63xx/patches-5.10/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch
bmips/patches-5.10/001-v5.11-mips-bmips-select-ARCH_HAS_RESET_CONTROLLER.patch
bmips/patches-5.10/041-v5.13-mtd-rawnand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch
bmips/patches-5.10/202-mips-bmips-disable-ARCH_HAS_SYNC_DMA_FOR_CPU_ALL.patch
bmips/patches-5.10/600-mips-bmips-add-pci-support.patch
generic/backport-5.10/103-v5.13-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch
generic/hack-5.10/301-mips_image_cmdline_hack.patch
generic/hack-5.10/402-mtd-blktrans-call-add-disks-after-mtd-device.patch
generic/hack-5.10/902-debloat_proc.patch
generic/pending-5.10/300-mips_expose_boot_raw.patch
generic/pending-5.10/495-mtd-core-add-get_mtd_device_by_node.patch
generic/pending-5.10/630-packet_socket_type.patch
ipq806x/patches-5.10/0072-add-ipq806x-with-no-clocks.patch
ipq806x/patches-5.10/099-1-mtd-nand-raw-qcom_nandc-add-boot_layout_mode-support.patch
lantiq/patches-5.10/0001-MIPS-lantiq-add-pcie-driver.patch
lantiq/patches-5.10/0023-NET-PHY-add-led-support-for-intel-xway.patch
lantiq/patches-5.10/0152-lantiq-VPE.patch

Deleted (reverse-appliable):
bmips/patches-5.10/052-v5.13-gpio-guard-gpiochip_irqchip_add_domain-with-GPIOLIB_.patch
generic/backport-5.10/499-v5.13-mtd-don-t-lock-when-recursively-deleting-partitions.patch

Deleted (alternative upstream fix):
ramips/patches-5.10/330-fix-pci-init-mt7620.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-05-14 14:50:03 +01:00
Rui Salvaterra
6a57e1fbfc kernel: bump 5.10 to 5.10.36
Automatically refreshed:
apm821xx/patches-5.10/802-usb-xhci-force-msi-renesas-xhci.patch
ath79/patches-5.10/410-spi-ath79-Implement-the-spi_mem-interface.patch
bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch
generic/pending-5.10/465-m25p80-mx-disable-software-protection.patch
ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch
ipq806x/patches-5.10/101-dwmac-ipq806x-qsgmii-pcs-all-ch-ctl.patch
ipq806x/patches-5.10/106-5.13-net-stmmac-Set-FIFO-sizes-for-ipq806x.patch

Deleted (empty or reverse-appliable):
ath79/patches-5.10/411-spi-ath79-add-SPI_MASTER_GPIO_SS-flag.patch
ath79/patches-5.10/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch
ath79/patches-5.10/0054-spi-sync-up-initial-chipselect-state.patch

Manually refreshed:
ath79/patches-5.10/0033-spi-ath79-drop-pdata-support.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-05-14 08:46:45 +01:00
Adrian Schmutzler
6780019892 ath79: fix sorting in generic 02_network
The two device strings were not ordered properly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-14 00:19:11 +02:00
Leonardo Mörlein
b993b68b6c build: introduce $(MKHASH)
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if

    make TOPDIR="$(pwd)" -C "$pkgdir" compile

was called manually. In most of the cases, I just saw warnings like this:

    make: Entering directory '/home/.../package/gluon-status-page'
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    bash: line 1: mkhash: command not found
    [...]

While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.

After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.

Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
2021-05-13 15:13:15 +02:00
David Bauer
a273ac4d61 ath79: ag71xx: fix error handling for of_get_phy_mode
Errors are not indicated by the phy_mode value but returned separately
from the function.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-10 01:19:32 +02:00
Ilya Lipnitskiy
89b99e9c1a treewide: consolidate named GPIO patch into hack-5.10
ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export
functionality. Consolidate the patch that adds it under hack-5.10 since
this logic is obviously not target-specific. For those who want to
disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-05-09 09:15:44 +02:00
Hauke Mehrtens
5d8ea6d34f ath79: Deactivate ZyXEL NBG6716 by default
The kernel image is too big now and the build fails.

WARNING: Image file zyxel_nbg6716-kernel.bin is too big: 4205404 > 4194304

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-05-02 15:00:40 +02:00
David Bauer
e5f81ea3fe ath79: drop cs-gpios property
The spi-ath79 driver performs the chipselect by writing to dedicated
register in the SPI register block. So the GPIO numbers were not used.

Tested-on: Enterasys WS-AP3705i

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-01 13:17:57 +02:00
David Bauer
bd54e73954 ath79: set number of chipselect lines
All chipsets from AR7100 up to QCA9563 have three dedicated chipselect
lines for the integrated SPI controller. Remove the number of
chipselects from the platform data, as there is no need to manually set
this to a different value.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-01 13:17:48 +02:00
David Bauer
a1d405ff8a ath79: add SPI_MASTER_GPIO_SS flag
Add the SPI_MASTER_GPIO_SS flag for the spi-ath79 driver. Otherwise,
the custom chipselect function is never called. This breaks hardware,
where the three dedicated chipselect lines are used instead of generic
GPIO pins.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-05-01 13:17:41 +02:00
Hauke Mehrtens
9ffa2f8193 kernel: Activate FORTIFY_SOURCE for MIPS kernel 5.4
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.

This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.

This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.

The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.

This increases the size of an uncompressed kernel by less than 1 KB.

Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-04-30 23:51:19 +02:00
Mauri Sandberg
4b14b42abf kernel: Move an upstreamed patch under backports
This CFI patch was accepted upstream for 5.13. Move it away from under
ath79 and place under backports to be removed in due time.

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
2021-04-30 23:48:37 +02:00
John Audia
0d2873df15 kernel: bump 5.4 to 5.4.114
Manually rebased*
  generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch

Added new backport*
  generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch

All others updated automatically.

The new backport was included based on this[1] upstream commit that will be
mainlined soon.  This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93

Signed-off-by: John Audia <graysky@archlinux.us>
2021-04-30 23:48:37 +02:00
Roger Pueyo Centelles
14a95b36b1 ath79: mikrotik: swap RB922UAGS-5HPaCD eth0/1 MACs
Since support for SFP on the MikroTik RouterBOARD 922UAGS-5HPacD was
added by 4387fe00cb, the MAC addresses for eth0 (Ethernet) and eth1
(SFP) were swapped. This patch fixes the 02_network script to assign MAC
addresses correctly, so they match the label and the vendor's OS.

Tested on a RouterBOARD 922UAGS-5HPacD board.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-04-30 10:01:00 +02:00
Stijn Tintel
f4473baf6e ath79: add missing kernel config symbol
Commit f724a583dc updated the nand-rb4xx driver to the 5.10 testing
kernel, but forgot to add the new kernel config symbol it introduces to
the 5.10 config.

Fixes: f724a583dc ("ath79: mikrotik: update nand-rb4xx driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-04-25 13:18:35 +03:00
Rui Salvaterra
182eaa4916 kernel: bump 5.10 to 5.10.32
Deleted (reverse-appliable):
mediatek/patches-5.10/360-mtd-rawnand-mtk-Fix-WAITRDY-break-condition-and-time.patch

Automatically refreshed:
ath79/patches-5.10/0036-GPIO-add-named-gpio-exports.patch
generic/backport-5.10/600-v5.12-net-extract-napi-poll-functionality-to-__napi_poll.patch
generic/backport-5.10/601-v5.12-net-implement-threaded-able-napi-poll-loop-support.patch
generic/backport-5.10/602-v5.12-net-add-sysfs-attribute-to-control-napi-threaded-mod.patch
generic/backport-5.10/603-v5.12-net-fix-race-between-napi-kthread-mode-and-busy-poll.patch
generic/pending-5.10/600-netfilter_conntrack_flush.patch
generic/pending-5.10/613-netfilter_optional_tcp_window_check.patch
generic/pending-5.10/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
generic/pending-5.10/768-net-dsa-mv88e6xxx-Request-assisted-learning-on-CPU-port.patch
lantiq/patches-5.10/0030-GPIO-add-named-gpio-exports.patch
ramips/patches-5.10/800-GPIO-add-named-gpio-exports.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-22 15:13:56 +01:00
Rui Salvaterra
3326b5e75c treewide: switch the timer frequency to 100 Hz
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:10 +01:00
Rui Salvaterra
27b5bae2ec treewide: remove redundant ubifs kconfig symbols
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:07 +01:00
Roger Pueyo Centelles
f724a583dc ath79: mikrotik: update nand-rb4xx driver
This updates the NAND driver for MikroTik RB4XX series to work with
kernel 5.10, similarly to the ar934x-nand driver (fb64e2c3).

Support for kernel 5.10 was added to all ath79 subtargets except for the
mikrotik one by commit d6b785d, since patch 920-mikrotik-rb4xx.patch
needed to be reworked. Later, commit f8512661 enabled kernel 5.10 for
the mikrotik subtarget with the nand-rb4xx driver still pending, which
is updated and added back by this patch.

Compile-tested only.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-04-17 21:56:05 +02:00
David Bauer
28623cab32 ath79: update spi-nor patches
Update the 4 bit BP patches for Ubiquiti boards with the second
iteration sent upstream.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-16 20:24:28 +02:00
David Bauer
2683eeb627 ath79: remove unused patch
This patch ist not required, as it only has an effect in case the GPIO
descriptors supplied to num-cs are valid.

As this is not the case for ath79, this patch can safely be omitted. The
issue it tried to fix is actually fixed with
0054-spi-sync-up-initial-chipselect-state.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-16 20:24:10 +02:00
Roger Pueyo Centelles
4387fe00cb ath79: mikrotik: enable SFP on RB922UAGS-5HPaCD
This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD.

GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable
or disable transmission, but no change is observed. Therefore, it is
left as output high to ensure the SFP module is forced to transmit.

Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD
1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router
iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port
or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers
950 Mbps symmetric.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2021-04-16 13:54:22 +02:00
David Bauer
bbff6239e2 ath79: fix 10 Mbit PLL data for TP-Link EAP2xx
Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP
boards using a AR8033 SGMII PHY.

Otherwise, 10 Mbit/s links do not transfer data.

Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-15 22:40:55 +02:00
David Bauer
956407292d ath79: fix 10 Mbit PLL data for UniFi AC
Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite
/ Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-15 22:40:48 +02:00
David Bauer
1f831927ee ath79: add missing patch for kernel 5.10
When adding the patch for the missing register, the patch file for the
testing kernel 5.10 was not included.

Fixes commit fbbad9a9a6 ("ath79: force SGMII SerDes
mode to MAC operation")
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-13 00:40:38 +02:00
David Bauer
fbbad9a9a6 ath79: force SGMII SerDes mode to MAC operation
The mode on the SGMII SerDes on the QCA9563 is 1000 Base-X by default.
This only allows for 1000 Mbit/s links, however when used with an SGMII
PHY in 100 Mbit/s link mode, the link remains dead.

This strictly has nothing to do with the SerDes calibration, however it
is done at the same point in the QCA reference U-Boot which is the
blueprint for everything happening here. As the current state is more or
less a hack, this should be fine.

This fixes the issues outlined above on a TP-Link EAP-225 Outdoor.

Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-04-13 00:32:56 +02:00
Koen Vandeputte
172fa3bc75 ath79: mikrotik: enable 2nd USB on RouterBOARD 922UAGS-5HPacD
RB922 boards have 2 separate USB controllers:
- 1 is connected to Slot Type A
- 1 is connected to the mini PCIe port

Enable the 2nd one too.

Before:

[    5.339304] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[    5.355053] SCSI subsystem initialized
[    5.364184] ehci-fsl: Freescale EHCI Host controller driver
[    5.372377] ehci-platform: EHCI generic platform driver
[    5.378053] ehci-platform 1b000000.usb: EHCI Host Controller
[    5.383861] ehci-platform 1b000000.usb: new USB bus registered,
assigned bus number 1
[    5.391932] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000
[    5.410730] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    5.417739] hub 1-0:1.0: USB hub found
[    5.422280] hub 1-0:1.0: 1 port detected
[    5.434007] usbcore: registered new interface driver usb-storage

After:

[    5.342988] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[    5.358687] SCSI subsystem initialized
[    5.367813] ehci-fsl: Freescale EHCI Host controller driver
[    5.375998] ehci-platform: EHCI generic platform driver
[    5.381695] ehci-platform 1b000000.usb: EHCI Host Controller
[    5.387507] ehci-platform 1b000000.usb: new USB bus registered,
assigned bus number 1
[    5.395571] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000
[    5.416050] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00
[    5.423089] hub 1-0:1.0: USB hub found
[    5.427578] hub 1-0:1.0: 1 port detected
[    5.432432] ehci-platform 1b400000.usb: EHCI Host Controller
[    5.438254] ehci-platform 1b400000.usb: new USB bus registered,
assigned bus number 2
[    5.446325] ehci-platform 1b400000.usb: irq 15, io mem 0x1b400000
[    5.468049] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00
[    5.475082] hub 2-0:1.0: USB hub found
[    5.479574] hub 2-0:1.0: 1 port detected
[    5.491305] usbcore: registered new interface driver usb-storage

Fixes: 8f93c05a59 ("ath79: add support for MikroTik RouterBOARD
922UAGS-5HPacD")
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
2021-04-12 13:18:30 +02:00
Jan Forman
328546e108 ath79: increase max SPI clock for DIR-859 A1
Increase the spi-max frequency to 50 MHz, similar to the DIR-842.

Signed-off-by: Jan Forman <forman.jan96@gmail.com>
[improve commit title, fix commit message alignment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-04-10 20:57:37 +02:00