Radxa ROCK 3B is a Pico-ITX form factor SBC[1] using the Rockchip
RK3568(J).
Hardware
--------
- Rockchip RK3568(J) SoC
- Quad A55 CPU
- Mali-G52 GPU
- 1 TOPS @ INT8 NPU
- 2GB/4GB/8GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key (2-lane PCIe 3.0)
- SPI Flash for bootloader
- 2x Gigabit ethernet port (one supports PoE with add-on PoE HAT)
- 1x M.2 E Key socket with SDIO, UART and USB interfaces
- 1x M.2 B Key socket with PCIe, SATA, and USB interfaces
- 1x SIM card socket
- 1x USB 3.0 Type-A HOST port
- 1x USB 3.0 Type-A OTG port
- 2x USB 2.0 Type-A HOST ports
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3b
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Radxa ROCK 3C is a high-performance, low-cost SBC[1] using the
Rockchip RK3566.
Hardware
--------
- Rockchip RK3566 SoC
- Quad A55 CPU
- Mali-G52-2EE GPU
- 1 TOPS @ INT8 NPU
- 1GB/2GB/4GB LPDDR4 RAM
- eMMC connector
- Micro SD Card slot
- NVMe SSD through the M.2 M Key connector(2230) or M.2 Extension
board(2232/2260/2280)
- SATA through the Radxa Penta SATA HAT
- 1x Gigabit ethernet port(supports PoE with add-on PoE HAT)
- WiFi6/BT5.4 (not supported yet on OpenWrt)
- 1x USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- 1x USB 2.0 Type-A OTG port
- 40 Pin GPIO header
[1] https://radxa.com/products/rock3/3c
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16185
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Another instance of files in build_dir symlinking to staging_dir. While
the symlinks do not currently cause any bugs in the libtool package,
such symlinks were found to make the build more fragile, as writing to
the symlink may accidentally modify the shared file in staging_dir. Pass
--copy to bootstrap to disable the symlinking.
Link: https://github.com/openwrt/openwrt/pull/15825
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In Gluon's Github Actions CI, we were occasionally seeing bizarre build
errors that looked like a config.sub file had been corrupted, or changed
while it was being executed.
The cause turned out to be an interaction of the symlinks created by
autoreconf (pointing from individual tools' build dirs into
`staging_dir/host/share/automake-1.16`) and OpenWrt's host-build.mk,
which replaced config.guess and config.sub *after* autoreconf. The
result was that the replacement of these files ended up following the
symlinks and writing the files in `staging_dir/host/share/automake-1.16`
instead of a package's build dir. This could cause other packages' builds
to fail if they were currently executing the scripts while they were
being written.
To fix this, disable autoreconf's symlinking feature, so that modifying
these files in a package's build directory can't accidentally affect the
staged versions.
Link: https://github.com/openwrt/openwrt/pull/15825
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
OpenWRT by default uses the Ninja generator, but some packages disable
Ninja and use the default Unix Makefiles generator. This generator can
be overridden in the user environment with `CMAKE_GENERATOR`. This patch
explicitly sets the correct generator when `PKG_USE_NINJA:=0`.
In particular, the `mt76` package uses the Makefiles generator.
Signed-off-by: Ivan Romanov <drizt72@zoho.eu>
Link: https://github.com/openwrt/openwrt/pull/16263
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
That patch title of 911-kobject_add_broadcast_uevent.patch has been
wrongly copied from 910-kobject_uevent.patch.
Change the description from "lib: add uevent_next_seqnum()" to
"lib: add broadcast_uevent()", so that the git history doesn't look
all weird when importing both patches to a git tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch fixes the list delimiter between 3GPP networks
passed to hostapd.
> list iw_anqp_3gpp_cell_net '262,001'
> list iw_anqp_3gpp_cell_net '262,002'
When passing a list of "iw_anqp_3gpp_cell_net" parameters via UCI,
hostapd would crash at startup:
> daemon.err hostapd: Line 73: Invalid anqp_3gpp_cell_net: 262,001:262,002
Using a semicolon as a delimiter, hostapd will start as expected.
Signed-off-by: Sarah Maedel <git@tbspace.de>
* Version 5 of this action updated the runtime to Node.js 20. All scripts are now run with Node.js 20 instead of Node.js 16 and are affected by any breaking changes between Node.js 16 and 20.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16251
Signed-off-by: Robert Marko <robimarko@gmail.com>
28b48a1 uim: add support for ICC communication channel
f582e00 qmi: fix dynamic array macro
d381f80 data: add support for ICC channel
Signed-off-by: David Bauer <mail@david-bauer.net>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes model name in dts as below:
Radxa ROCK3 model A -> Radxa ROCK 3A
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16232
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch fixes model name in dts as below:
Radxa ROCK3 model A -> Radxa ROCK 3A
Radxa ROCK 5 model A -> Radxa ROCK 5A
Radxa ROCK 5 model B -> Radxa ROCK 5B
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/16232
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Like x86, armsr is frequently virtualized, and is used for development
and debugging. Kernel messages should be more readily apparent by
default. This can be achieved by adding console=tty1 to the kernel
command line, enabling the console on a (possibly virtual) display and
keyboard, in addition to a serial port.
This also enables failsafe on tty1. Failsafe mode operates on consoles
known by the kernel, without regard to /etc/inittab.
armsr's /etc/inittab is also updated to specify tty1 instead of tty0.
tty1 is technically more correct: tty1 is the first virtual console,
where tty0 reflects the current active virtual console (which is likely
to be tty1).
This configuration matches x86, which is another target commonly used
for virtualization, development, and debugging in the same way. x86's
kernel command line had specified console=tty0, although console=tty1 is
more correct for the reasons given above. This also brings x86's kernel
command line console= into agreement with its /etc/inittab, which
already used tty1.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16213
Signed-off-by: Robert Marko <robimarko@gmail.com>
Found with coccinelle:
No need to set .owner here. The core will do it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16217
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use local tarballs instead of upstream generated ones. Smaller.
Fix version to be compatible with apk.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16219
Signed-off-by: Robert Marko <robimarko@gmail.com>
Forward client mac address and subnet on dns queries. Pi-hole and Adguard use this feature to send the originators ip address/subnet so it can be logged and not just the nat address of the router. This feature has been added since version 2.56 of dnsmasq and would be nice to expose this feature in openwrt.
Signed-off-by: Carsten Schuette <schuettecarsten@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/15965
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link TD-W8968 v3 is an 300Mbps Wireless N USB ADSL2+ Modem Router based on
Broadcom BCM6318 SoC.
Hardware:
CPU: Broadcom BCM6318, 333 MHz, 1 core
Flash: 8MB
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Wireless: 802.11b/g/n, BCM43217
LEDs/Buttons: 10x / 3x
USB: 1x 2.0
Flash instructions:
* Assign static IP 192.168.1.100 to PC
* Unplug the power source
* Press the RESET button at the router, don't release it yet!
* Plug the power source. Wait for some seconds
* Release the RESET button
* Browse to http://192.168.1.1
* Upload the openwrt-bmips-bcm6318-tp-link_td-w8968-v3-squashfs-cfe.bin file
* Wait some minutes until the firmware upgrade finish.
Signed-off-by: Mathesh Velayudan <123v.mathesh@gmail.com>
There was a typo done for mt7925e and mt7925u in the KernelPackage
definitions, which caused the system to load the wrong kernel modules.
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16236
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The firmware binaries were missing in kmod-mt7925-firmware package.
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16239
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On latest Intel x86 CPUs, DMC firmware is required for the iGPU to reach
its lowest power states. If the driver cannot load it, it will print a
warning and unnecessarily make the iGPU draw a bit more power when idle.
GUC firmware (various "offload" mechanisms that deal with scheduling GPU
workloads) and HUC firmware (required for accelerated media codec
operations for HEVC/H.265) are probably more niche, but could also
provde useful for some - for example, when building an
Intel/OpenWrt-based security camera.
Signed-off-by: Johannes Truschnigg <johannes@truschnigg.info>
Link: https://github.com/openwrt/openwrt/pull/16069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Device support for Sophos AP15 is based on Sophos AP55(C) and AP100(C).
Those other Sophos access points uss a QCA9558 SoC (some of them with
one of the three chains on the built-in SoC's wifi disabled) while the
AP15 uses a QCA9557 SoC (which only has two chains enabled in the
package or silicon).
This is mostly cosmetic since QCA9558 and QCA9557 are virtually
identical and all differences are automatically detected and/or managed
by the ART calibration.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/16187
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16230
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit introduces led nodes in tl-wdr4900-v1 dts.
It allows to configure switch leds from userspace.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link tl-wdr4900-v1 has two usb leds. Modern kernels can handle usb
led trigger. Let's enable it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit change led description in dts file from old method to new
approach accepted by upstream.
USB power gpio is handled by gpio-export now.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16226
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ever since CONFIG_ARM64_PAN was enabled Common Not Private (CNP) is now
visible and kernel builds will stop as they are not set in kernel config
for 5.15 and 6.1.
So, lets enable Common Not Private (CNP) which is ARMv8.2 feature and will
be NOP of CPU-s that dont support it.
Fixes: a2662309aa ("kernel: Enable CONFIG_ARM64_PAN to restrict kernel access to user space memory")
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enhanced Privileged Access Never (EPAN) is an ARMv8.7 feature, and since
we dont have any SoC-s implementing it lets disable it.
Link: https://github.com/openwrt/openwrt/pull/16211
Signed-off-by: Robert Marko <robimarko@gmail.com>
The commit backporting new MTK patches did not update the
Kernel config for mediatek/mt7622 causing the build to
fail.
Simply use the new config symbol name for the driver to
fix the issue.
Fixes: 1069514978 ("mediatek: backport pending Ethernet PHY driver patches")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16225
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use pending patchset for 2.5GE PHY driver, unifying LED handling
accross all MediaTek Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
