ExternalVendorCode/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2024-12-27 09:12:39 +00:00
Code Issues Actions 4 Packages Projects Releases Wiki Activity
58,576 Commits 9 Branches 76 Tags 923 MiB
1ec1aa9cc7
Commit Graph

35 Commits

Author SHA1 Message Date
Roland Reinl
6e51ff88b0 filogic: Add support for D-Link AQUILA PRO AI M30 
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - MT7531 switch
 - 512MB RAM
 - 128MB NAND flash with two UBI partitions with identical size
 - 1 multi color LED (red, green, blue, white) connected via GCA230718
 - 3 buttons (WPS, reset, LED on/off)
 - 1 1Gbit WAN port
 - 4 1Gbit LAN ports

Disassembly:
 - There are four screws at the bottom: 2 under the rubber feets, 2 under the label.
 - After removing the screws, the white plastic part can be shifted out of the blue part.
 - Be careful because the antennas are mounted on the side and the top of the white part.

Serial Interface
 - The serial interface can be connected to the 4 pin holes on the side of the board.
 - Pins (from front to rear):
   - 3.3V
   - RX
   - TX
   - GND
 - Settings: 115200, 8N1

MAC addresses:
 - WAN MAC is stored in partition "Odm" at offset 0x81
 - LAN (as printed on the device) is WAN MAC + 1
 - WLAN MAC (2.4 GHz) is WAN MAC + 2
 - WLAN MAC (5GHz) is WAN MAC + 3

Flashing via Recovery Web Interface:
 - The recovery web interface always flashes to the currently active partition.
 - If OpenWrt is flahsed to the second partition, it will not boot.
 - Ensure that you have an OEM image available (encrypted and decrypted version). Decryption is described in the end.
 - Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
 - Press the reset button while powering on the device
 - Keep the reset button pressed until the LED blinks red
 - Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
 - Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-recovery.bin
 - The recovery web interface always reports successful flashing, even if it fails
 - After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
 - If OpenWrt was flashed to the first partition, OpenWrt will boot (The status LED will start blinking white and stay white in the end). In this case you're done and can use OpenWrt.
 - If OpenWrt was flashed to the second partition, OpenWrt won't boot (The status LED will stay red forever). In this case, the following steps are reuqired:
   - Start the web recovery interface again and flash the **decrypted OEM image**. This will be flashed to the second partition as well. The OEM firmware web interface is afterwards accessible via http://192.168.200.1.
   - Now flash the **encrypted OEM image** via OEM firmware web interface. In this case, the new firmware is flashed to the first partition. After flashing and the following reboot, the OEM firmware web interface should still be accessible via http://192.168.200.1.
   - Start the web recovery interface again and flash the OpenWrt recovery image. Now it will be flashed to the first partition, OpenWrt will boot correctly afterwards and is accessible via 192.168.1.1.

Flashing via U-Boot:
 - Open the case, connect to the UART console
 - Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
 - Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-initramfs-kernel.bin.
 - Power on the device and select "7. Load image" in the U-Boot menu
 - Enter image file, tftp server IP and device IP (if they differ from the default).
 - TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
 - The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
 - Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-m30-a1-squashfs-sysupgrade.bin
 - Reboot the device. OpenWrt should start from flash now

Revert back to stock using the Recovery Web Interface:
 - Set your IP address to 192.168.200.2, subnetmask 255.255.255.0
 - Press the reset button while powering on the device
 - Keep the reset button pressed until the LED blinks red
 - Open a Chromium based and goto http://192.168.200.1 (recovery web interface)
 - Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.

Decrypting a D-Link firmware image:
 - Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
 - Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
 - Run ./m32-firmware-util M30 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
 - Example for firmware M30A1_FW101B05: ./m32-firmware-util M30 --DecryptFactoryImage M30A1_FW101B05\(0725091522\).bin M30A1_FW101B05\(0725091522\)_decrypted.bin

Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.

Controlling the LEDs:
 - The LEDs are controlled by a chip called "GCA230718" which is connected to the main CPU via I2C (address 0x40)
 - I didn't find any documentation or driver for it, so the information below is purely based on my investigations
 - If there is already I driver for it, please tell me. Maybe I didn't search enough
 - I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
 - The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
 - The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
 - Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
 - Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
   - A reset command (0x81 0xE4) written to register 0x00
   - A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
 - The reset command is always the same
 - In the control command
   - byte 0 is always the same
   - byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
   - byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
   - byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
   - byte 7 defines the toggling frequency (if toggling enabled)
   - byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
   - byte 12 is constant 0x87

Comparison to M32/R32:
 - The algorithms for decrypting the OEM firmware are the same for M30/M32/R32, only the keys differ
 - The keys are available in the GPL sources for the M32
 - The M32/R32 contained raw data in the firmware images (kernel, rootfs), the R30 uses a sysupgrade tar instead
 - Creation of the recovery image is quite similar, only the header start string changes. So mostly takeover from M32/R32 for that.
 - Turned out that the bytes at offset 0x0E and 0x0F in the recovery image header are the checksum over the data area
 - This checksum was not checked in the recovery web interface of M32/R32 devices, but is now active in R30
 - I adapted the recovery image creation to also calculate the checksum over the data area
 - The recovery image header for M30 contains addresses which don't match the memory layout in the DTS. The same addresses are also present in the OEM images
 - The recovery web interface either calculates the correct addresses from it or has it's own logic to determine where which information must be written

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(cherry picked from commit 29cca6cfee)
 2024-07-08 23:06:38 +02:00
Chukun Pan
7bfdc4ea3a uboot-mediatek: add Netcore N60 support 
The vendor uboot requires special fit verification.
So add a custom uboot build for this device.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 0170666d89)
 2024-07-08 12:00:39 +02:00
Tianling Shen
2a25de25fa mediatek: add support for JDCloud RE-CP-03 
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: 128GB eMMC
  RAM: 1GB DDR4
  Ethernet: 4x 1GbE, 1x 2.5GbE (RTL8221B)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Joylink
  Power: DC 12V 2A

Flash instructions:
1. Download and flash the vendor migration firmware via webUI:
   https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7986-jdcloud_re-cp-03-vendor-migration.bin
   (Default address is 192.168.68.1, user root, no password)
2. After device has booted up, write new GPT table:
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-jdcloud_re-cp-03-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit c0c3234e17)
 2024-07-08 09:08:48 +02:00
David Bentham
9ac1523062 mediatek: add Comfast CF-E393AX support 
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.

Oem firmware is a custom openwrt 21.02 snapshot version.

We can gain access via ssh once we remove the root password.

Hardware specification:
  SoC: MediaTek MT7981A 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB DDR3
  Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
            1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976D
  LEDS: 1x (Red, Blue and Green)
  Button: Reset
  UART: 3.3v, 115200n8
  --------------------------
  | Layout |
  | ----------------- |
  | 4 | VCC GND TX RX | <= |
  | ----------------- |
  --------------------------

Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
   and download the
   configuration(http://apipaddress/computer/config.html).

2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
   Enter 'fakeroot' command then decompress the configuration:
   tar -zxf backup.tar.gz

3. Edit 'etc/shadow', update (remove) root password:
   With password =
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
   to
   Without password =
   'root::0:99999:7:::'
   'root::0:99999:7:::'

4. Repack 'etc' directory back to a new backup file:
   tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
   Exit fakeroot - 'exit'

6. Upload new configuration via web interface, now you
   can SSH with the following:

   'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.

   Backup the mtd partitions
   - https://openwrt.org/docs/guide-user/installation/generic.backup

7. Copy openwrt factory firmware to the tmp folder to install via ssh:

   'scp -o HostKeyAlgorithms=+ssh-rsa \
   -o PubkeyAcceptedAlgorithms=+ssh-rsa \
   *-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
   root@192.168.10.1:/tmp/'

   'sysupgrade -n -F \
   /tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'

8. Once led has stopped flashing - Connect via ssh with the
   default openwrt ip address - 'ssh root@192.168.1.1'

9. SSH copy the openwrt sysupgrade firmware and upgrade
   as per the default instructions.

Signed-off-by: David Bentham <db260179@gmail.com>
(cherry picked from commit d8f4453bf2)
 2024-07-04 15:54:27 +02:00
Chukun Pan
e4015c446b uboot-envtools: filogic: reorder alphabetically 
Reorder scripts to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 4825defe44)
 2024-07-04 15:39:22 +02:00
Ian Oderon
77354213b7 mediatek: add support for Zbtlink ZBT-Z8103AX 
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.

Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi

Buttons:
Reset-Mesh

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Signed-off-by: Ian Oderon <ianoderon@gmail.com>
(cherry picked from commit 4300bc6688)
 2024-07-03 09:19:41 +02:00
Chuanhong Guo
51822a907e mediatek: drop NMBM layout for Xiaomi WR30U 
This reverts commit dcdcfc1511.

This is a firmware for third-party u-boot mod, which should not
be carried here by us.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 1b7e62b20b)
 2024-05-23 21:50:00 +02:00
Dim Fish
f11e6e221e mediatek: filogic: add support for Xiaomi AX3000T 
**SoC**: MediaTek MT7981B 2x A53
  **Flash**: ESMT F50L1G41LB 128MB
  **RAM**: NT52B128M16JR-FL 256MB
  **Ethernet**: 4x 10/100/1000 Mbps
  **Switch**: MediaTek MT7531AE
  **WiFi**: MediaTek MT7976C
  **Buttons**: Reset, Mesh
  **Power**: DC 12V 1A

1. Get ssh access. Supported stock firmware **1.0.47**
   ```
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A"
   curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A
   ```

2. Backup stock partitions
   ```
   nanddump -f /tmp/BL2.bin /dev/mtd1
   nanddump -f /tmp/Nvram.bin /dev/mtd2
   nanddump -f /tmp/Bdata.bin /dev/mtd3
   nanddump -f /tmp/Factory.bin /dev/mtd4
   nanddump -f /tmp/FIP.bin /dev/mtd5
   nanddump -f /tmp/ubi.bin /dev/mtd8
   nanddump -f /tmp/KF.bin /dev/mtd12
   ```
   Then transfer them to your computer in a safe place.

3. Get firmware information `cat /proc/cmdline`

4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash
   If **firmware=0**
   ```
   ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=1
   nvram set flag_last_success=1
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```
   If **firmware=1**
   ```
   ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
   nvram set boot_wait=on
   nvram set uart_en=1
   nvram set flag_boot_rootfs=0
   nvram set flag_last_success=0
   nvram set flag_boot_success=1
   nvram set flag_try_sys1_failed=0
   nvram set flag_try_sys2_failed=0
   nvram commit
   reboot
   ```

   Then reboot your router, it should boot to the OpenWrt initramfs system now.

5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin`

1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

   `reboot`

2. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

3. Format ubi and create new ubootenv volume
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
   ```

4. *(Optional **-10Mb** free space) Add recovery boot feature.*
   ```
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
   ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   ```

5. Flash Openwrt U-Boot
   ```
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2
   mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP
   ```

6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb
   `sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb`

1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
   `sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`

2. Format ubi and Nvram
   ```
   ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
   mtd erase Nvram
   ```

3. Install kmod-mtd-rw
   `opkg update && opkg install kmod-mtd-rw`

   `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`

4. Flash stock images from backup
   ```
   mtd write /tmp/BL2.bin BL2
   mtd write /tmp/FIP.bin FIP
   mtd write /tmp/ubi.bin ubi
   ```
   Then reboot your router, waiting it finished rollback in minutes.

   `ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
   Then reboot your router, waiting it finished rollback in minutes.

Signed-off-by: Dim Fish <dimfish@gmail.com>
(cherry picked from commit 7dbcc1215a)
 2024-05-23 21:50:00 +02:00
Nicolò Veronese
02272df01c uboot-envtools: add support for Zyxel EX5601-T0 ubootmod 
The ubootmod bootlaoder for EX5601-T0 uses two partitions
 in ubi to store enviroment variables. so proper config
 is needed.

Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
(cherry picked from commit 2a0805fd3d)
 2024-03-12 23:13:38 +01:00
Xavier Franquet
7338733dc9 mediatek: filogic: add support ASUS RT-AX59U 
(based on support for ASUS RT-AX59U by liushiyou006)

SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)

Upgrade from AsusWRT to OpenWRT using UART

    Download the OpenWrt initramfs image.
    Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.

    Connect the PC with TFTP server to the RT-AX59U.
    Set a static ip on the ethernet interface of your PC.
    (ip address: 192.168.1.70, subnet mask:255.255.255.0)
    Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.

    Download & Boot the OpenWrt initramfs image.

    $ setenv ipaddr 192.168.1.1
    $ setenv serverip 192.168.1.70
    $ tftpboot 0x46000000 rtax59u.bin
    $ bootm 0x46000000

    Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.

    $ sysupgrade -n <path-to-sysupgrade.bin>

Upgrade from AsusWRT to OpenWRT using WebUI

    Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq

    Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file

    Wait for OpenWRT to boot (192.168.1.1).

    Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command

MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.

              : Stock             : OpenWrt
  WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
  WLAN 2g (2) :                   : CA:xx:xx:0D:xx:D4
  WLAN 2g (3) :                   : CE:xx:xx:0D:xx:D4
  WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
  WLAN 5g (2) :                   : CE:xx:xx:1D:xx:D5
  WLAN 5g (3) :                   : C2:xx:xx:1D:xx:D5

  WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
  WLAN 2g (2) :                   : 0A:xx:xx:76:xx:BE
  WLAN 2g (3) :                   : 0E:xx:xx:76:xx:BE
  WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
  WLAN 5g (2) :                   : 0E:xx:xx:76:xx:BF
  WLAN 5g (3) :                   : 02:xx:xx:76:xx:BF

Signed-off-by: Xavier Franquet <xavier@franquet.es>
(cherry picked from commit 782eb05008)
 2024-01-20 19:07:15 +01:00
Mikhail Zhilkin
51881b2eb9 mediatek: add support for Routerich AX3000 
This PR is continuation of work under "mediatek: add support for Routerich
AX3000" #13703 by the agreement with PR #13703 original author (Maximilian
Weinmann <x1@disroot.org>). All reviews from the previous PR were taken
into into account.

Routerich AX3000 is a wireless WiFi 6 router.

Specification
-------------
- SoC       : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM       : DDR3 256 MiB (ESMT M15T2G16128A)
- Flash     : SPI-NAND 128 MiB (ESMT F50L1G41LB)
- WLAN      : MediaTek MT7976CN dual-band WiFi 6
  - 2.4 GHz : b/g/n/ax, MIMO 2x2
  - 5 GHz   : a/n/ac/ax, MIMO 2x2
- Ethernet  : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
- USB       : 1x 2.0
- UART      : through-hole on PCB
  - [J500] GND, TX, RX, 3.3V (115200n8)
- Buttons   : Mesh, Reset
- LEDs      : 1x Power (Blue)
              1x WiFi 2.4 GHz (Blue)
              1x WiFi 5 GHz (Red)
              1x Mesh (Blue)
              3x LAN activity (Blue)
              1x WAN activity (Blue)
              2x WAN no-internet (Red)
- Power     : 12 VDC, 1.5 A

Installation
------------
Flash OpenWrt 'sysupgrade.bin' image using stock firmware web-interface
(without keeping settings).

Return to stock
---------------
Install stock firmware image (without keeping settings) using OpenWrt
sysupgrade method.

Recovery
--------
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 24:0f:5e:xx:xx:b4 | label     |
| LAN     | 24:0f:5e:xx:xx:b5 | label+1   |
| WLAN 2g | 24:0f:5e:xx:xx:b6 | label+2   |
| WLAN 5g | 24:0f:5e:xx:xx:b7 | label+3   |
+---------+-------------------+-----------+
The WLAN 2g MAC was found in 'Factory', 0x4

Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 485adc9d3c)
[Fix merge conflict in uboot-envtools]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
 2024-01-04 21:47:43 +01:00
Daniel Golle
d9246902b0 mediatek: add support for Zbtlink ZBT-Z8102AX 
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND

Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware

B. Through TFTP
Standard installation via UART:

1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.

Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c8c2f52262)
 2023-12-09 13:39:53 +01:00
Chukun Pan
4f9c4113c4 uboot-mediatek: add JCG Q30 PRO support 
The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b42c527228)
 2023-12-08 07:35:46 +01:00
Jianhui Zhao
b530d492a9 filogic: add support for GL.iNet GL-MT6000 
Hardware specification:
* SoC: MediaTek MT7986A 4x A53
* Flash: 8GB EMMC
* RAM: 1GB DDR4
* Ethernet:
  * 2x2.5G RJ45 port (RTL8221B)
  * 4x1G RJ45 ports (MT7531AE)
* WLAN:
  * 2.4GHz: MT7976GN 4T4R
  * 5GHz: MT7976AN 4T4R
* Button: Reset
* LED: 1 x dual color LED
* USB: 1 x USB 3.0
* Power: DC 12V 4A
* UART: 3V3 115200 8N1 (Pinout: GND TX RX VCC)
* JTAG: 9 PIN

If you want to use u-boot from OpenWrt, you can upgrade it safely.
* bl2: openwrt-mediatek-filogic-glinet_gl-mt6000-preloader.bin
* fip: openwrt-mediatek-filogic-glinet_gl-mt6000-bl31-uboot.fip

`openwrt-mediatek-filogic-glinet_gl-mt6000-squashfs-factory.bin` is used in OpenWrt's u-boot.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
(cherry picked from commit fe10f97439)
 2023-12-07 09:46:36 +01:00
Elbert Mai
28d15e2040 mediatek: filogic: add support for Ubiquiti UniFi 6 Plus (U6+) 
Ubiquiti U6+ is a dual-band WiFi 6 PoE access point.
It is a drop-in upgrade of the U6 lite.

Specifications
---

- SoC: MediaTek MT7981A dual-core ARM Cortex-A53 1.3 GHz
- RAM: 256 MB DDR3-2133 RAM
- Flash: 16 MB SPI NOR and 4 GB eMMC
- LAN: 1x Gigabit Ethernet with 802.3af/at support
- WLAN: MediaTek MT7976C 2x2 MIMO dual-band WiFi 6
- LEDs: 1x blue and 1x white
- Buttons: 1x reset button

Installation
---

1. Power device using a PoE injector or switch
2. Connect via Ethernet to the device with static IP 192.168.1.2
3. SSH into the device with password: ubnt

        $ ssh ubnt@192.168.1.20

4. Unlock kernel partitions for writing

        $ echo 5edfacbf > /proc/ubnthal/.uf

5. Confirm correct partitions

        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p6/uevent
        PARTNAME=kernel0
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p7/uevent
        PARTNAME=kernel1
        $ grep PARTNAME /sys/block/mmcblk0/mmcblk0p8/uevent
        PARTNAME=bs

6. Set and confirm bootloader environment

        $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt"
        $ fw_setenv bootcmd_real "run boot_openwrt"
        $ fw_printenv

7. Copy sysupgrade image to /tmp/openwrt.bin via scp
8. Copy kernel and rootfs to mmcblk0p6 and mmcblk0p7, respectively

        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/kernel -O | dd of=/dev/mmcblk0p6
        $ tar xf /tmp/openwrt.bin sysupgrade-ubnt_unifi-6-plus/root -O | dd of=/dev/mmcblk0p7

9. Ensure device boots from mmcblk0p6

        $ echo -ne "\x00\x00\x00\x00\x2b\xe8\x4d\xa3" > /dev/mmcblk0p8

10. Reboot the device

        $ reboot

Signed-off-by: Elbert Mai <code@elbertmai.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 75ee5546e9)
 2023-12-07 09:45:33 +01:00
Patricia Lee
e1d1c26c0f mediatek: add support for Cetron CT3003 
**Hardware specification:**

- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
  | Layout:   |
  | :-------- |
  | <Antenna> |
  | VCC       |
  | GND       |
  | Tx        |
  | Rx        |

**Flash instructions:**

1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.

**Notes:**

If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.

Signed-off-by: Patricia Lee <patricialee320@gmail.com>
(cherry picked from commit 907e9e0bd3)
 2023-12-07 09:39:35 +01:00
Bjørn Mork
3846b6eb49 filogic: support Telenor branded ZyXEL EX5700 
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.

Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
  cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
  back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree

Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
  unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
  refuses to boot if it doesn't. The chosen "rootfs" volume must contain
  a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
  variable to the label mac.  But "factoryparams" does not always
  exist.  Instead there is a "RIP" volume containing all the factory
  data.  Copying the "RIP" volume to  "factoryparams" will fix this

Hardware
--------
SOC:   MediaTek MT7986
RAM:   1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI:  Mediatek MT7986 802.11ax 5 GHz
       Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH:   MediaTek MT7531 Switch + SoC
       3 x builtin 1G phy (lan1, lan2, lan3)
       2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB:   1 x USB 3.2 Enhanced SuperSpeed port
UART:  3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)

Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
   reachable at 192.168.1.2/24. Rename the image to C0A80101.img.

2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
   console, Interrupt the autoboot process by pressing ESC when prompted.

3. Download and boot the OpenWrt initramfs image.

   $ env set uboot_bootcount 0
   $ env set firmware nominal
   $ tftpboot
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Missing features
----------------

- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
  OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
  not configured by OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 6cc14bf66a)
 2023-12-07 08:00:33 +01:00
Tianling Shen
d3c193525e mediatek: add CMCC RAX3000M support 
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 64GB eMMC or 128 MB SPI-NAND
  RAM: 512MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A
- UART: 3.3v, 115200n8
  --------------------------
  |         Layout         |
  |   -----------------    |
  | 4 | GND TX VCC RX | <= |
  |   -----------------    |
  --------------------------

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
   tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
   'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
   tar -zcf cfg_export_config_file.conf etc/
   * If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
     just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.

Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH    CMIIT ID: xxxx" is NAND version

eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
   ('data' partition can be ignored, it's useless.)
2. Write new GPT table:
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
   echo 0 > /sys/block/mmcblk0boot0/force_ro
   dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
   dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync

NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
   mtd erase BL2
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
   mtd erase FIP
   mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
   ubidetach -p /dev/mtd0
   ubiformat -y /dev/mtd0
   ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
   ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
   ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
     (Don't worry! You will always have TFTP recovery boot feature.)
   ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
   ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 423186d7d8)
[rebased to 23.05]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
 2023-11-07 00:46:00 +01:00
Stefan Agner
f445c38263 mediatek: filogic: wax220: cleanup device tree 
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.

Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit 4af06aaf33)
 2023-08-22 13:40:10 +02:00
Hank Moretti
34d8913bd5 mediatek: filogic: add specific layout for WR30U 
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.

This layout is the same as the ubootmod layout but enabling NMBM.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
 2023-08-07 16:31:27 +01:00
Hank Moretti
d0fc9e96be uboot-mediatek: add support for Xiaomi WR30U 
Add a custom uboot build to support openwrt uboot layout.

Signed-off-by: Hank Moretti <mchank9999@gmail.com>
 2023-08-07 16:31:27 +01:00
Chukun Pan
f7daeec3bd uboot-mediatek: add H3C Magic NX30 Pro support 
The OEM uboot limit brush into 3rd-party firmware.
So add a custom uboot build to support openwrt.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 437e79ad6d)
 2023-07-13 12:05:28 +01:00
Mikhail Zhilkin
7ff95775a2 mediatek: add support for Mercusys MR90X v1 
This commit adds support for Mercusys MR90X(EU) v1 router.

Device specification
--------------------
SoC Type:   MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM:        MediaTek MT7986BLA (512MB)
Flash:      SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
Ethernet:   MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet:   1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2)
WLAN 2g:    MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g:    MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs:       1 orange and 1 green status LEDs, 4 green gpio-controlled
            LEDs on ethernet ports
Button:     1 (Reset)
USB ports:  No
Power:      12 VDC, 2 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
            slots contain "seconduboot" (also U-Boot 2022.01-rc4)

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |
    +--- Don't connect

The R3 (TX line) and R6 (RX line) are absent on the PCB. You should
solder them or solder the jumpers.

Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Once inside OpenWrt, set / update env variables:
      fw_setenv baudrate 115200
      fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
      fw_setenv fdtcontroladdr 5ffc0e70
      fw_setenv ipaddr 192.168.1.1
      fw_setenv loadaddr 0x46000000
      fw_setenv mtdids "spi-nand0=spi-nand0"
      fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
      fw_setenv netmask 255.255.255.0
      fw_setenv serverip 192.168.1.2
      fw_setenv stderr serial@11002000
      fw_setenv stdin serial@11002000
      fw_setenv stdout serial@11002000
      fw_setenv tp_boot_idx 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Installation (without UART)
---------------------------
1.  Login as root via SSH (router IP, port 20001, password - your web
    interface password)
2.  Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and
    SSH settings from the p.1)
3.  Add a newline after "#!/bin/sh":
       telnetd -l /bin/login.sh
4.  Save "65-iptv" file
5.  Toggle "IPTV/VLAN Enable" checkbox in the router web interface and
    save
6.  Make sure that telnetd is running:
       netstat -ltunp | grep 23
7.  Login via telnet to router IP, port 23 (no username and password are
    required)
8  Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the
    router (e.g., using WinSCP and SSH settings from the p.1)
9.  Stock busybox doesn't contain ubiupdatevol command. Hence, we need to
    download and upload the full version of busybox to the router. For
    example, from here:
    https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64
    Upload busybox-arm64 to the /tmp dir of the router and run:
    in the telnet shell:
       cd /tmp
       chmod a+x busybox-arm64
10. Check "initramfs-kernel.bin" size:
       du -h initramfs-kernel.bin
11. Delete old and create new "kernel" volume with appropriate size
    (greater than "initramfs-kernel.bin" size):
       ubirmvol /dev/ubi0 -N kernel
       ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB
12. Write OpenWrt "initramfs-kernel.bin" to the flash:
       ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin
13. u-boot-env can be empty so lets create it (or overwrite it if it
    already exists) with the necessary values:
       fw_setenv baudrate 115200
       fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit"
       fw_setenv fdtcontroladdr 5ffc0e70
       fw_setenv ipaddr 192.168.1.1
       fw_setenv loadaddr 0x46000000
       fw_setenv mtdids "spi-nand0=spi-nand0"
       fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)"
       fw_setenv netmask 255.255.255.0
       fw_setenv serverip 192.168.1.2
       fw_setenv stderr serial@11002000
       fw_setenv stdin serial@11002000
       fw_setenv stdout serial@11002000
       fw_setenv tp_boot_idx 0
14. Reboot to OpenWrt initramfs:
       reboot
15. Login as root via SSH (IP 192.168.1.1, port 22)
16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
17. Run sysupgrade:
       sysupgrade -n /tmp/sysupgrade.bin

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
   upload the OEM firmware

Recovery (UART)
---------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot initramfs-kernel.bin
      bootm
4. Do what you need (restore partitions from a backup, install OpenWrt
   etc.)

Stock layout
------------
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"

ubi0/ubi1 format
----------------
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot   Vol ID: 0|
| Volume Name: kernel  Vol ID: 1|
| Volume Name: rootfs  Vol ID: 2|
+-------------------------------+

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| label   | 00:eb:xx:xx:xx:be | label     |
| LAN     | 00:eb:xx:xx:xx:be | label     |
| WAN     | 00:eb:xx:xx:xx:bf | label+1   |
| WLAN 2g | 00:eb:xx:xx:xx:be | label     |
| WLAN 5g | 00:eb:xx:xx:xx:bd | label-1   |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac". OEM wireless eeprom is also there (file
"MT7986_EEPROM.bin").

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit e4fe3097ef)
[Fix merging conflict]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
 2023-07-01 15:16:17 +00:00
Jianhui Zhao
42c99789ac uboot-envtools: Add u-boot env config for GL-MT3000 
This commit add u-boot env config for GL-MT3000, so
that we can use fw_printenv to print u-boot env and
use fw_setenv to set u-boot env in GL-MT3000.

Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
(cherry picked from commit 6892603efa)
 2023-07-01 11:49:25 +02:00
Flole Systems
cd17d8df2a
filogic: add support for Netgear WAX220 
Hardware
--------
SOC:   MediaTek MT7986
RAM:   1024MB DDR3
FLASH: 128MB SPI-NAND (Winbond)
WIFI:  Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH:   Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE
UART:  3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)

Installation
------------

1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect the TFTP server to the WAX220. Conect to the serial console,
   interrupt the autoboot process by pressing '0' when prompted.
3. Download & Boot the OpenWrt initramfs image.

   $ setenv ipaddr 192.168.2.1
   $ setenv serverip 192.168.2.2
   $ tftpboot openwrt.bin
   $ bootm

4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
   using scp and install using sysupgrade.

   $ sysupgrade -n <path-to-sysupgrade.bin>

Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
(cherry picked from commit 984786a2f7)
 2023-06-26 13:20:39 +02:00
Chukun Pan
99c94c6696 uboot-mediatek: add Qihoo 360T7 support 
The vendor uboot will verify firmware at boot.
So add a custom uboot build for this device.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit c51eb17730)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
 2023-05-29 13:04:14 +01:00
Pietro Ameruoso
22d7148689 mediatek: add support for Zyxel EX5601-T0 router 
Zyxel EX5601-T0 specifics
--------------
The operator specific firmware running on the Zyxel branded
EX5601-T0 includes  U-Boot modifications affecting the OpenWrt
installation.

Partition Table
| dev  | size     | erasesize | name          |
| ---- | -------- | --------- | ------------- |
| mtd0 | 20000000 | 00040000  | "spi0.1"      |
| mtd1 | 00100000 | 00040000  | "BL2"         |
| mtd2 | 00080000 | 00040000  | "u-boot-env"  |
| mtd3 | 00200000 | 00040000  | "Factory"     |
| mtd4 | 001c0000 | 00040000  | "FIP"         |
| mtd5 | 00040000 | 00040000  | "zloader"     |
| mtd6 | 04000000 | 00040000  | "ubi"         |
| mtd7 | 04000000 | 00040000  | "ubi2"        |
| mtd8 | 15a80000 | 00040000  | "zyubi"       |

The router boots BL2 which than loads FIP (u-boot).
U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated.
Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked.
Too zloader checks that the firmware contains a particolar file called zyfwinfo.
Additional details regarding Zloader can be found here:
https://hack-gpon.github.io/zyxel/
https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914

Hardware
--------
SOC: MediaTek MT7986a
CPU: 4 core cortex-a53 (2000MHz)
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Micron xxx)
WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4)
1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
VOIP: 2 FXS ports for analog phones

MAC Address Table
-----------------
eth0/lan    Factory 0x002a
eth1/wan    Factory 0x0024
wifi 2.4Ghz Factory 0x0004
wifi 5Ghz   Factory 0x0004 + 1

Serial console (UART)
---------------------
+-------+-------+-------+-------+-------+
| +3.3V |  RX   |  TX   |  KEY  |  GND  |
+---+---+-------+-------+-------+-------+
    |
    +--- Don't connect

Installation
------------
Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs.
The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities.

1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2):
- Attach a usb-ttl adapter to your computer and boot the router.
- While the router is booting at some point you will read the following: `Please press Enter to activate this console.`
- As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling).
- Most likely the router is still printing the boot log, leave it boot until it stops.
- If everything went ok you should have full root access "root@EX5601-T0:/#".
- Type the following command and press enter: "fw_setenv EngDebugFlag 0x1".
- Reboot the router.
- As soon as you read `Hit any key to stop autoboot:` press Enter.
- If everything went ok you should have the following prompt: "ZHAL>".
- You have successfully unlocked zloader access, this procedure must be done only once.

2. Check the current active partition:
- Boot the router and repeat the steps above to gain root access.
- Type the following command to check the current active image: "cat /proc/cmdline".
- If `rootubi=ubi` it means that the active partition is `mtd6`
- If `rootubi=ubi2` it means that the active partition is `mtd7`
- As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back.
- To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands:
atbt 1  # unlock write
atsw    # swap boot partition
atsr    # reboot the router
- After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2
- If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong.

3. Flashing:
- Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar.
Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes).
I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same:
https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh
- Add the zyfwinfo file into the sysupgrade tar.
- Enter via telnet or ssh into the router with admin credentials
- Enter the following commands to disable the firmware and model checks
"zycli fwidcheck off" and "zycli modelcheck off"
- Open the router web interface and in the update firmware page select the "restore default settings option"
- Select the sysupgrade file and click on upload.
- The router will flash and reboot itself into openwrt from UBI

4. Restoring and going back to Zyxel firmware.
- Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following:
atbt 1  # unlock write
atsw    # swap boot partition
atsr    # reboot the router
- You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt.

Working features
----------------
3 gbit lan ports
Wifi
Zyxel partitioning for coexistance with Zloader and dual boot.
WAN SFP port (only after exporting pins 57 and 10. gpiobase411)
leds
reset button
serial interface
usb port
lan ethernet 2.5 gbit port (autosense)
wan ethernet 2.5 gbit port (autosense)

Not working
----------------
voip (missing drivers or proper zyxel platform software)

Swapping the wan ethernet/sfp xor port
----------------
The way to swap the wan port between sfp and ethernet is the following:
export the pins 57 and 10.
Pin 57 is used to probe if an sfp is present.
If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value).
If pin 57 value is 1 it means that no sfp is inserted into the cage.
In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one.
After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too.
This is totally scriptable of course.

Leds description
------------
All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan).
To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools.
To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools.
Example:
Set lan5 led to fast blink on 2500/1000, slow blink on 10/100:
mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC

Set wan 2.5gbit led to constant on when wan is 2.5gbit:
mdio mdio-bus mmd 6:30 raw 0x0001 0x0080

Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
(cherry picked from commit 1c05388ab0)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
 2023-05-24 19:26:11 +01:00
Daniel Golle
cc00e22029 uboot-mediatek: add TP-Link TL-XDR4288 and TL-XDR608x 
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.

The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
 2023-04-22 04:10:19 +01:00
Daniel Golle
90dbdb4941 uboot-envtools: filogic: bpi-r3: fix env selection 
Selecting the environment when booting from SD card has been broken by
a previous commit. Fix it.

Fixes: f46355b4d7 ("uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
 2023-01-29 03:43:58 +00:00
Chuanhong Guo
d29dbf052a
mediatek: drop redmi-ax6000 variant with modified env 
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
 2022-12-30 16:11:59 +08:00
Furong Xu
1613e3340b uboot-mediatek: add support for Xiaomi Redmi Router AX6000 
U-Boot flash instructions:

0. OpenWrt U-Boot does not support stock layout, it comes with recovery
boot support, automatic tftp recovery and never blocks UART.

A new flash layout is introduced, we call it OpenWrt U-Boot layout,
stock flash layout and the old OpenWrt layout are not supported.

During the whole flash procedure, please do not reboot or power off
unless requested explicitly, or you will break your device.

1. Your device should already running OpenWrt.
If not, follow the instructions to flash OpenWrt:
https://github.com/openwrt/openwrt/pull/11115

2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or
in case you want to go back to stock firmware one day.

cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin

And save all whose bin files to somewhere safe.

Then backup your configurations, since ubiformat for entire mtd device is
required to create new ubootenv volume for OpenWrt U-Boot.

3. Run the following cmd to boot into an initramfs with the new OpenWrt
U-Boot layout that expand ubi partion to the end of flash:

ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi

4. After boot into initramfs, check mtd partion info.
The ubi partion should be mtd5

root@OpenWrt:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi

5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.

To install kmod-mtd-rw via opkg:

opkg update && opkg install kmod-mtd-rw

Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.

Load kmod-mtd-rw:
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

6. Run the following cmd to clean all pending crash dumps in pstore,
or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.

rm -f /sys/fs/pstore/*

7. Format ubi and create new ubootenv volume:

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB

8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb

9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.

mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP

10. Flash the squashfs-sysupgrade.bin as usual:

sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb

Enjoy!

Signed-off-by: Furong Xu <xfr@outlook.com>
 2022-12-29 03:04:42 +00:00
Chen Minqiang
18bea173a6 mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000 
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.

1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
   stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
   to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
   be helpful for users who may forget to do this before sysupgrade in
   the initramfs.

New flash instructions:
1. Gain ssh access. Please refer to:
   https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)

2. Check which system current u-boot is loading from:
   COMMAND: `cat /proc/cmdline`
   sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
   if firmware=1, current system is ubi1
   if firmware=0, current system is ubi0

3. Setup nvram and write the firmware:
   If the current system is ubi1, please set it up so that the next time
   it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
   If the current system is ubi, please set it up so that the next time
   it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```

4. After rebooting, the system should now boot into the openwrt initramfs.
   Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.

For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:

1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```

2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
 2022-12-17 15:04:16 +08:00
Chukun Pan
641e4f2f04 mediatek: add Xiaomi Redmi Router AX6000 support 
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128 MB
  RAM: K4A4G165WF-BCWE 512 MB
  Ethernet: 4x 10/100/1000 Mbps
  WiFi1: MT7976GN 2.4GHz ax 4x4
  WiFi2: MT7976AN 5GHz ax 4x4
  Button: Mesh, Reset

Flash instructions:
  1. Gain ssh and serial port access, see the link below:
     https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
  2. Use ssh or serial port to log in to the router, and
     execute the following command:
     nvram set boot_wait=on
     nvram set flag_boot_rootfs=0
     nvram set flag_boot_success=1
     nvram set flag_last_success=1
     nvram set flag_try_sys1_failed=8
     nvram set flag_try_sys2_failed=8
     nvram commit
  3. Set a static ip on the ethernet interface of your computer
     (e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
  4. Download the initramfs image, rename it to initramfs.bin,
     and host it with the tftp server.
  5. Interrupt U-Boot and run these commands:
     setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
     saveenv
     tftpboot initramfs.bin
     bootm
  6. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Revert to stock firmware:
  Restore mtdparts back to default, then use the
  vendor's recovery tool (Windows only).

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
 2022-10-30 14:30:22 +00:00
Daniel Golle
f46355b4d7
uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed 
Fix accessing the environment in case no OS is installed on the flash
media selected for boot as this is possible when booting initramfs.
In case of relying on the device specified to be mounted as rootfs to
be present, rather just use the kernel cmdline 'root' variable as a
hint to decide where to read/write the U-Boot environment.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
 2022-10-18 20:08:53 +01:00
Daniel Golle
38f7e932a5 uboot-envtools: add support for Bananapi BPi-R3 
Create new mediatek_filogic file and add entries for environment on
MMC, UBI and NOR for the Bananapi BPi-R3.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
 2022-08-30 13:36:28 +01:00