Commit Graph

23695 Commits

Author SHA1 Message Date
Adrian Schmutzler
cc75344044 bcm27xx: remove no-op patch pair
Patch 1 introduces a change, and patch 2 reverts it again. Remove
both patches and achieve the same outcome.

Refreshed patches for the target as well.

Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-20 14:19:39 +02:00
John Audia
da98603597 kernel: bump 5.4 to 5.4.58
This PR is a blend of several kernel bumps authored by ldir taken from his
staging tree w/ some further adjustments made by me and update_kernel.sh

Summary:
Deleted upstreamed patches:
  generic:
    742-v5.5-net-sfp-add-support-for-module-quirks.patch
    743-v5.5-net-sfp-add-some-quirks-for-GPON-modules.patch
  bcm63xx:
    022-v5.8-mtd-rawnand-brcmnand-correctly-verify-erased-pages.patch
    024-v5.8-mtd-rawnand-brcmnand-fix-CS0-layout.patch
  mediatek:
    0402-net-ethernet-mtk_eth_soc-Always-call-mtk_gmac0_rgmii.patch

Deleted patches applied differently upstream:
  generic:
    641-sch_cake-fix-IP-protocol-handling-in-the-presence-of.patch

Manually merged patches:
  generic:
    395-v5.8-net-sch_cake-Take-advantage-of-skb-hash-where-appropriate.patch
  bcm27xx:
    950-0132-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch
  layerscape:
    701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch

Build system: x86_64
Build-tested: ath79/generic, bcm27xx/bcm2708, bcm27xx/bcm2711,
  imx6, mvebu/cortexa9, sunxi/a53
Run-tested: Netgear R7800 (ipq806x)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-By: Lucian Cristian <Lucian.cristian@gmail.com> [mvebu]
Tested-By: Curtis Deptuck <curtdept@me.com> [x86/64]
[do not remove 395-v5.8-net-sch_cake-Take-advantage-... patch,
adjust and refresh patches, adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-By: John Audia <graysky@archlinux.us> [ipq806x]
2020-08-18 18:14:54 +02:00
Thibaut VARÈNE
2cac31223d ath79: mikrotik: erase firmware on SPI NOR before install
On Mikrotik SPI NOR devices, the firmware partition must be erased when
flashing from stock firmware, otherwise leftover bits (in particular a
kernel signature) can trigger a boot loop.

When booted from initramfs (the only way to install OpenWRT on these
devices), this patch unconditionally erases the firmware partition in
the do_upgrade() stage for all supported SPI NOR devices.

This is forward-ported from ed49d0876 and 20452a8db

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-08-18 12:24:12 +02:00
Thibaut VARÈNE
d0498872ff generic: platform/mikrotik: fix incorrect test
The test is meant to check the result of the preceding kmalloc()

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-08-18 12:00:55 +02:00
Adrian Schmutzler
5388c72517 Revert "bcm53xx: remove useless echo in 02_network"
This reverts commit b1f6a5d9df.

In this particular case, the echo command was _not_ useless, but
converted the newlines back to spaces.

Add a comment into the code to make that obvious for the next one
looking at it like me.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-18 11:46:59 +02:00
Adrian Schmutzler
b1f6a5d9df bcm53xx: remove useless echo in 02_network
The output is already produced in the inner $() brackets, no need
to catch and echo it again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 23:16:58 +02:00
Adrian Schmutzler
84fc80dd66 rockchip: remove useless echo in 40-net-smp-affinity
The command in the $() brackets will already provide the same output.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 23:13:57 +02:00
Adrian Schmutzler
1a75443964 apm821xx: tidy up 10-fix-wifi-mac
This applies some cosmetic style fixes:
- remove useless echo
- remove double equal sign (specific to bash)
- add quotes for -n check

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 23:09:37 +02:00
Adrian Schmutzler
e329e71c69 ath79: fix syntax error in ar7240_tplink_tl-wa.dtsi
The node needs to be terminated by a semicolon.

Fixes: 8484a764df ("ath79: ar724x: make sure builtin-switch is
enabled in DT")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 18:26:55 +02:00
Adrian Schmutzler
48c3d5c884 ath79: change WPS to Wifi button on TL-WPA8630P v2
Both TL-WPA8630(P) v1 and v2 feature a button labelled "WiFi".
While this is implemented as KEY_RFKILL for v1 in ar71xx and ath79,
the v2 sets it up as WPS button.

According to the manual, the behavior in OEM firmware is:
"Press and hold the button for 1 second to copy wireless settings
from the main router to the extender. Go to Wi-Fi Clone for more
information. Press and hold the button for at least 5 seconds to
turn the wireless function on or off."

Consequently, and since this is historic behavior on v1 in OpenWrt,
we set this button to KEY_RFKILL on both revisions.

Fixes: ab74def0db ("ath79: add support for TP-Link TL-WPA8630P v2")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:25:51 +02:00
Adrian Schmutzler
57e029ba57 ipq806x: move further common nodes to the DTSI files
The moves a few additional common nodes to the common DTSI files
for qcom-ipq8064-v2.0 and qcom-ipq8065 devices.

Remove a few redundant definitions on the way.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:25:11 +02:00
Adrian Schmutzler
8484a764df ath79: ar724x: make sure builtin-switch is enabled in DT
On ar7240/ar7241 the mdioX node with the builtin-switch is enabled
in the DTSI files, but the parent ethX node is left disabled. It
only gets enabled per device or device family, and has not been
enabled at all yet for the TP-Link WA devices with ar7240, making
the switch unavailable there.

This patch makes sure &eth0/&eth1 nodes are enabled together with
the &mdio0/&mdio1 nodes containing the builtin-switch.
For ar7240_tplink_tl-wa.dtsi, &eth0 is properly hidden again via
  compatible = "syscon", "simple-mfd";

This partially fixes FS#2887, however it seems dmesg still does
not show cable (dis)connect in dmesg for ar7240 TP-Link WA
devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:19:03 +02:00
Adrian Schmutzler
03cdbb2040 ramips: fix LED labels for Asus RT-AC65P
The leds block was copied over from the RT-AC85P DTS to the common
DTSI while keeping the device-specific model name in the label.

This moves the LEDs back to the DTS files and adjusts the names to
properly resemble the model name of the devices used at, just like
it is handled on most other devices.

Fixes: 7c5f712e4f ("ramips: add support for Asus RT-AC65P")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 15:00:43 +02:00
Adrian Schmutzler
e38d89ea55 at91: drop obsolete empty Makefiles
This files have been emptied during subtarget consolidation, but
not removed. Remove them now.

Fixes: aff084adf3 ("at91: Merge SAMA5 subtargets")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-17 01:22:36 +02:00
Donald Hoskins
eadb1a9437 octeon: add support for Itus Shield Router
Itus Networks Shield - 1Ghz dual-core mips64 / Cavium Octeon 3 SoC,
1Gb RAM, 4Gb eMMC,3 GbE 10/100/1000 ports

Information regarding device can be found:
https://deviwiki.com/wiki/Itus_Networks_Shield_Pro

Installing OpenWrt on Itus Networks Shield:

1) Boot Shield
2) On device: mount /dev/mmcblk1p1 /mnt
3) scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin to
   /mnt/ItusrouterImage
3a) Optionally: scp openwrt-octeon-itus,shield-router-initramfs-kernel.bin
    to /mnt/ItusgatewayImage to allow you to have an emergency recovery
    boot in the GATEWAY slot - this slot will have no permament storage and
    is used for emergency recovery only when booted in the (G)ateway
    position
4) On device: umount /mnt
5) reboot

Once booted, run the sysupgrade via cli or luCi on the
openwrt-octeon-itus,shield-router-squashfs-sysupgrade.tar file the mode
you are running.

Once rebooted, the system installation is complete. Your storage partition
for the mode is inialized and set.

Signed-off-by: Donald Hoskins <grommish@gmail.com>
[cut out sysupgrade-* changes, move a few lines,
drop case CVMX_BOARD_TYPE_ITUS_SHIELD]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-16 02:15:06 +02:00
Donald Hoskins
591767fc01 octeon: determine sysupgrade-* directory for upgrade automatically
So far, the sysupgrade-* folder used during upgrade in octeon was
hardcoded to contain the board name. Therefore, changing board name
or BOARD_NAME variable in image/Makefile might have broken upgrade.

Improve this by adding a step to determine the folder name via
a wildcard, as it is done for generic nand_upgrade_tar() in
lib/upgrade/nand.sh.

While this still does not remove the problem for existing devices
(which still have the old script), it will entirely remove the
issue on newly added devices on this platform.

Signed-off-by: Donald Hoskins <grommish@gmail.com>
[split into separate patch, add commit message, add return values]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-16 02:14:34 +02:00
Adrian Schmutzler
d43b963b3d bcm63xx: reorganize board patches
This renames board patches to make finding devices easier
and reorders them based on their board.

The devices are grouped based on the board/cpu_id. New device
patches should be numbered based on their group.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-16 01:03:39 +02:00
Tomasz Maciej Nowak
ebf71533f9 ath79: add support for ALLNET ALL-WAP02860AC
ALLNET ALL-WAP02860AC is a dual-band wireless access point.

Specification
SoC: Qualcomm Atheros QCA9558
RAM: 128 MB DDR2
Flash: 16 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
      5 GHz 3T3R QCA9880 Mini PCIe card
Ethernet: 1x 10/100/1000 Mbps AR8035-A, PoE capable (802.3at)
LEDS: 5x, which four are GPIO controlled
Buttons: 1x GPIO controlled
UART: 4 pin header near Mini PCIe card, starting count from white
      triangle on PCB
      1. VCC 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

MAC addresses
Calibration data does not contain valid MAC addresses.
The calculated MAC addresses are chosen in accordance with OEM firmware.

Because of:
a) constrained environment (SNMP) when connecting through Telnet
   or SSH,
b) hard-coded kernel and rootfs sizes,
c) checksum verification of kerenel and rootfs images in bootloder,

creating factory image accepted by OEM web interface is difficult,
therefore, to install OpenWrt on this device UART connection is needed.
The teardown is simple, unscrew four screws to disassemble the casing,
plus two screws to separate mainboard from the casing.
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.

Installation
1. Prepare TFTP server with OpenWrt initramfs-kernel image.
2. Connect to LAN port.
3. Connect to UART port.
4. Power on the device and when prompted to stop autoboot, hit any key.
5. Alter U-Boot environment with following commands:
    setenv failsafe_boot bootm 0x9f0a0000
    saveenv
6. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
   'setenv' to do that, then run following commands:
    tftpboot 0x81000000 <openwrt_initramfs-kernel_image_name>
    bootm 0x81000000
7. Wait about 1 minute for OpenWrt to boot.
8. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
   with:
    sysupgrade -n /tmp/<openwrt_sysupgrade_image_name>
9. After flashing, the access point will reboot to OpenWrt. Wait few
   minutes, until the Power LED stops blinking, then it's ready for
   configuration.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[add MAC address comment to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-15 15:58:39 +02:00
Tony Ambardar
2932b4d05e kernel: mips: fix init crash/bootloop on 64-bit systems
The malta subtargets for mips64 and mips64el fail to start the init process
at boot, resulting in a boot loop. The issue was raised and analyzed within
FS#3277. Investigation suggested code near the [vdso] memory area of the
process was long jumping into a region inaccessible to the process, e.g.

 init: - preinit -
 init: Launched preinit instance, pid=522
 do_page_fault(): sending SIGSEGV to init for invalid read access from 0000000000000360
 epc = 0000000000000360 in init[aaab42b000+4000]
 ra  = 000000fffee385e0 in
 Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
 Rebooting in 1 seconds..

Note the low-memory read access and epc are the same. Upstream kernel 5.6
included a relevant patch and discussion:

  * d3f703c4359f ("mips: vdso: fix 'jalr t9' crash in vdso code")

Disassembly of the failing kernel's vdso.so confirmed presence of the
telltale long jumps, e.g.:

00000000000007c0 <__vdso_clock_getres@@LINUX_2.6>:
 [...]
 7dc:   0320f809        jalr    t9
 [...]

Restore booting mips64/mips64el malta by backporting the above commit:
  * 310-v5.6-mips-vdso-fix-jalr-t9-crash-in-vdso-code.patch

Fixes: 54310a3aa0 ("malta: add kernel 5.4 config")
Fixes: FS#3277
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3277

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-08-15 00:04:59 +08:00
Adrian Schmutzler
7ef7dbaf70 ath79: add support for TP-Link TL-WPA8630 v1
This ports the TP-Link TL-WPA8630 v1 from ar71xx to ath79.

Specifications:

SoC: QCA9563
CPU: 750 MHz
Flash/RAM: 8 / 128 MiB
Ethernet: 3x 1G ports (QCA8337 switch)
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac (ath10k)

Buttons, LEDs and network setup appear to be almost identical
to the v2 revision.

Powerline interface is connected to switch port 5 (Label LAN4).

Installation:

No "fresh" device was available for testing the factory image.

It is not known whether flashing via OEM firmware GUI is possible
or not. A discussion from 2018 [1] about that indicates a few
adjustments are necessary, but it is not clear whether those
are already implemented with the TPLINK_HEADER_VERSION = 2 or not.

Note that for the TL-WPA8630P v1, the TPLINK_HWID needs to be
changed to 0x86310001 to allow factory flashing.

[1] https://forum.openwrt.org/t/solved-tl-wpa8630p-lede-does-not-install/8161/27

Recovery:

Recovery is only possible via serial.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 20:43:15 +02:00
Adrian Schmutzler
488da882f5 mpc85xx: tidy up 10-fix-wifi-mac
This applies some cosmetic style fixes, mostly by removing useless
echo commands.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 20:29:20 +02:00
Adrian Schmutzler
ef765ceb09 ath79/mikrotik: add function for loading ath9k caldata
The commands to read ath9k caldata on mikrotik subtarget are
mostly repetitive, so let's put them into a function to make
writing and reading them easier.

This function will only be required when patching the MAC address.
For cases where it is put correctly into the calibration data by
the vendor, caldata_sysfsload_from_file can be used directly as
done for ath10k at the moment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
John Thomson
74438d5419 ramips: add support for MikroTik RouterBOARD 760iGS (hEX S)
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.

https://mikrotik.com/product/hex_s

Specifications:

- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM:  256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot

Unsupported:

- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
  The linux driver requires an interrupt, and pendown GPIO
  These are unknown, and not needed with the touchscreen
  only used for temperature and voltage monitoring.
  ads7846 hwmon:
  temp0 is degrees Celsius
  temp1 is voltage * 32

GPIOs:

- 07:  input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17:  output passive PoE out (lan5) switch

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

To boot to intramfs image in RAM:

1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
   Wait (~25 seconds) for beep and then release reset button.
   The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
   check by plugging in to port 2-5 and going to 192.168.1.1.

To install OpenWrt to flash:

1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.

OEM firmware differences:

- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.

[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
Adrian Schmutzler
ddf3e5c22d ramips/mt7621: create common DTSI for Mikrotik devices
This moves some common definitions for Mikrotik devices, mainly
routerboot partitions and reset key, to a common DTSI file.

While at it, remove unused hard_config DT label.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 12:47:45 +02:00
John Thomson
2d9db93397 ramips: use gpio-export for Mikrotik RouterBOARD 750Gr3 beeper
This beeper hardware requires a PWM driver for frequency selection.
Since the GPIO driver does not provide that, revert the beeper
support to a simple gpio-export.

This effectively reverts the corresponding changes from
6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-13 02:12:12 +02:00
Ansuel Smith
87e92d50e5 kernel: usb: move phy-qcom-ipq806x-usb to ipq806x modules.mk
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Ansuel Smith
35d1f05094 ipq806x: replace nvmem qcom patch with upstream version
- Replace nvmem qcom patch with upstream version
- Update compatible

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches, minor commit message rewording]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Ansuel Smith
0c45ad41e1 ipq806x: replace phy dwc3 patch with upstream version
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
2020-08-13 02:12:12 +02:00
Adrian Schmutzler
6e7f40dff3 ath79: routerboard-92x: ensure explicit bios size in DTSI
The missing "size" property was acceptable in the context of a single
DTS as the underlying device is known to have a 64KB flash, and thus
the bios partition fit exactly between the preceding and following ones.

However as this block has moved in a DTSI, for the sake of clarity and
explicitness the size property is added to ensure that if the flash
happens to be larger than expected, the bios partition remains properly
sized.

Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 16:49:34 +02:00
Adrian Schmutzler
5dc74ad7f3 ath79: harmonize appearance of ethX nodes in qca953x DTSes
This harmonizes the appearance of ethX nodes in qca953x DTSes by:
- having the same order of nodes and properties
- removing redundant status property on eth1 (set in qca953x.dtsi)

This is meant to help both copy-pasters and reviewers, since
deviations and errors can be spotted easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:44:07 +02:00
Adrian Schmutzler
92b4f16bab kernel: add CGROUPS and IOSCHED_BFQ back to config
After those symbols have been removed from generic kernel config,
they were added to the target config during every kernel config
refresh. As that's not desirable, add them back to the generic
config.

Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Fixes: cfe235c436 ("kernel: modules: add package kmod-iosched-bfq")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Roger Pueyo Centelles
151e43df7a ath79: add support for MikroTik SXT 5nD r2 (SXT Lite5)
The MikroTik SXT Lite5 (product code RBSXT5nDr2, also SXT 5nD r2) is
an outdoor 5GHz CPE with a 16 dBi integrated antenna built around the
Atheros AR9344 SoC. It is based on the "sxt5n" board platform.

Specifications:
 - SoC: Atheros AR9344
 - RAM: 64 MB
 - Storage: 128 MB NAND
 - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
    8-32 Vdc PoE in
 - 6 user-controllable LEDs:
  · 1x power (blue)
  · 1x wlan (green)
  · 4x rssi (green)
 - 1 GPIO-controlled buzzer

 See https://mikrotik.com/product/RBSXT5nDr2 for more details.

Notes:
 The device was already supported in the ar71xx target. There, the
 Ethernet port was handled by GMAC1. Here in ath79 it is handled by
 GMAC0, which allows to get link information (loss, speed, duplex) on
 the eth0 interface.

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Acknowledgments:
 Michael Pratt (@mpratt14) for helping on the network settings.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, use mikrotik LED label prefix, make names consistent,
add reg for bootloader2, use led_user for boot indication etc.,
minor cosmetic changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Sven Roederer
b2e1f7101d ath79: add support for MikroTik RouterBOARD 921GS-5HPacD-15s
The MikroTik RouterBOARD 921GS-5HPacD-15s (mANTBox 15s) is an outdoor
antenna for 5 GHz with an built-in router. This ports the board from
ar71xx.

See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9558 (720 MHz)
 - RAM: 128 MB
 - Storage: 128 MB NAND
 - Wireless: external QCA9892 802.11a/ac 2x2:2
 - Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
 - SFP: 1x host

Working:
 - NAND storage detection
 - Ethernet
 - Wireless
 - 1x user LED (blinks during boot, sysupgrade)
 - Reset button
 - Sysupgrade

Untested:
 - SFP cage (probably not working)

Installation (untested):
 - Boot initramfs image via TFTP and then flash sysupgrade image

As the embedded RB921-pcb is a stripped down version of the RB922 this patch
adds a common dtsi for this series and includes this to the final dts-files.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[move ath10k-leds closer to ath10k definition in DTS files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Roger Pueyo Centelles
7a705c067f ath79: add support for MikroTik RouterBOARD LHG 2nD
The MikroTik RouterBOARD LHG 2nD (sold as LHG 2) is a 2.4 GHz
802.11b/g/n outdoor device with a feed and an integrated dual
polarization grid dish antenna based on the LHG-HB platform.

See https://mikrotik.com/product/lhg_2 for more info.

Specifications:
 - SoC: Qualcomm Atheros QCA9533
 - RAM: 64 MB
 - Storage: 16 MB NOR
 - Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 18 dBi antenna
 - Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 12-28 Vdc PoE in
 - 8 user-controllable LEDs:
   · 1x power (blue)
   · 1x user (green)
   · 1x lan (green)
   · 1x wlan (green)
   · 4x rssi (green)

Note:
 The rssihigh LED is disabled, as it shares GPIO 16 with the reset
 button.

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, remove rssiled setup, adjust commit message, add DTSIs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 14:03:17 +02:00
Felix Fietkau
ed19ba04e8 mediatek: disable btif in device tree to make the WMAC work again
btif and wmac access the same resources and at the moment enabling one
breaks the other

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-12 13:02:13 +02:00
Felix Fietkau
74a66c0204 mediatek: fix PCI device tree node for elecom wrc-2533gent
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-12 13:02:13 +02:00
Adrian Schmutzler
d0cb71a896 bcm47xx: use vendor_model scheme for device/image names
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.

Apply this to bcm47xx as well. This does _not_ apply any other
specific naming changes.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Adrian Schmutzler
683bcbdce1 bcm53xx: use vendor_model scheme for device/image names
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.

Apply this to bcm53xx as well. This does _not_ apply any other
specific naming changes.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-12 11:08:05 +02:00
Hauke Mehrtens
c43af7a6cb kernel: Fix cake patch for kernel 4.19.138
This fixes the following build problem with cake:
net/sched/act_ctinfo.c: In function 'tcf_ctinfo_act':
net/sched/act_ctinfo.c:99:6: error: implicit declaration of function 'tc_skb_protocol'; did you mean 'skb_protocol'? [-Werror=implicit-function-declaration]
  if (tc_skb_protocol(skb) == htons(ETH_P_IP)) {
      ^~~~~~~~~~~~~~~
      skb_protocol
  CC [M]  net/sched/sch_hfsc.o

Fixes: fdac05b741 ("kernel: Update kernel 4.19 to version 4.19.138")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-11 21:11:53 +02:00
Hauke Mehrtens
2e8785d68c kernel: Create UBIFS v5 volume
In commit 87b35c16ad ("kernel: ubifs: create use file system format 4
by default") we changed the default UBIFS version used when the kernel
creates a new volume from 5 to 4. UBIFS v5 was added in kernel 4.10 and
only kernel 4.10 and later can read it.
We changed the kernel to create version 4 volumes also on more recent
kernel versions to make it possible to downgrade to an OpenWrt version
with kernel 4.9, the upgrade still works. This is probably not needed
any more and we can remove this patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-11 21:11:53 +02:00
Álvaro Fernández Rojas
a5a0b3f1d0 bcm63xx: switch to upstream CFE detection patch
This patch has been merged in linux 5.9.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-11 08:04:40 +02:00
Tony Ambardar
da4651833c malta: disable unnecessary built-in CDROM support
The CDROM is not needed for booting and can be included by selecting the
loadable module as a package instead.

This also avoids triggering a memory allocation failure during probing of
the CDROM due to lack of low 16MB DMA memory, as decribed in FS#3278:
https://bugs.openwrt.org/index.php?do=details&task_id=3278

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/3289
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-08-11 11:25:42 +08:00
Daniel Golle
5793112f75 oxnas: reduce size of ATA DMA descriptor space
After years of trying to find the reason for random kernel crashes
while both CPU and SATA are under load it has been found.
Some odd commented-out #defines in kref's single-port driver [1] which
were copied from the vendor driver made me develop a theory:
The IO-mapped memory area for DMA descriptors apparetly got some holes
just before the alignment boundaries.
This feels like an off-by-one bug in the hardware or maybe those fields
are used internally by the SATA controller's firmware.
Whatever the cause is: they cannot be used and trying to use them
results in reading back unexpected stuff and ends up with oopsing
Unable to handle kernel paging request at virtual address d085c004

Work around the issue by reducing the area used for bmdma descriptors.
This reduces SATA performance (iops) quite a bit, but finally makes
things work reliably. Possibly one could optimize this much more by
really just skipping the holes in that memory area -- however, that
seems to be non-trivial with the driver and libata in it's current form
(suggestions are welcome).
The 'proper' way to have good SATA performance would be to make use of
the hardware RAID features (one can use the JBOD mode to access even
just a single disc transparently through the RAID controller integrated
in the SATA host instead of accessing the SATA ports 'raw' as we do
now).

[1]: https://github.com/kref/linux-oxnas/blob/master/drivers/ata/sata_oxnas.c#L25

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-11 00:16:04 +01:00
Christoph Krapp
0af656e978 ar71xx: fix ZyXEL NBG6616 wifi switch
The device uses a rf-kill switch instead of a button. Furthermore the
GPIO is active high.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-08-11 01:12:22 +02:00
Hauke Mehrtens
b35c54227b kernel: Move CONFIG_IONIC to generic kernel config
It is deactivated everywhere, just set this in the generic config.

Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 23:58:58 +02:00
Hauke Mehrtens
eafdd1a0fc malta: Refresh kernel configuration
This refreshes the kernel configuration on top of kernel 5.4.
It now builds without asking to select some kernel options on all 4
subtargets.
It still does not boot up, there is a different problem.

Tested-By: Yousong Zhou <yszhou4tech@gmail.com>
Acked-By: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 23:58:58 +02:00
Hauke Mehrtens
2f3d7abccd kernel: Update kernel 4.14 to version 4.14.193
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 19:34:37 +02:00
Hauke Mehrtens
fdac05b741 kernel: Update kernel 4.19 to version 4.19.138
Compile and run tested on lantiq/xrx200

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-08-10 19:34:37 +02:00
Christoph Krapp
459c8c9ef8 ath79: add support for ZyXEL NBG6616
Specifications:

  SoC: Qualcomm Atheros QCA9557
  RAM: 128 MB (Nanya NT5TU32M16EG-AC)
  Flash: 16 MB (Macronix MX25L12845EMI-10G)
  Ethernet: 5x 10/100/1000 (1x WAN, 4x LAN)
  Wireless: QCA9557 2.4GHz (nbg), QCA9882 5GHz (ac)
  USB: 2x USB 2.0 port
  Buttons: 1x Reset
  Switches: 1x Wifi
  LEDs: 11 (Pwr, WAN, 4x LAN, 2x Wifi, 2x USB, WPS)

MAC addresses:

WAN *:3f uboot-env ethaddr + 3
LAN *:3e uboot-env ethaddr + 2
2.4GHz *:3c uboot-env ethaddr
5GHz *:3d uboot-env ethaddr + 1

The label contains all four MAC addresses, however the one without
increment is first, so this one is taken for label MAC address.

Notes:

The Wifi is controlled by an on/off button, i.e. has to be implemented
by a switch (EV_SW). Despite, it appears that GPIO_ACTIVE_HIGH needs
to be used, just like recently fixed for the NBG6716.
Both parameters have been wrong at ar71xx.

Flash Instructions:

At first the U-Boot variables need to be changed in order to boot the
new combined image format. ZyXEL uses a split kernel + root setup and
the current kernel is too large to fit into the partition. As resizing
didnt do the trick, I've decided to use the prefered combined image
approach to be future-kernel-enlargement-proof (thanks to blocktrron for
the assistance).

First add a new variable called boot_openwrt:
setenv boot_openwrt bootm 0x9F120000

After that overwrite the bootcmd and save the environment:
setenv bootcmd run boot_openwrt
saveenv

After that you can flash the openwrt factory image via TFTP. The servers
IP has to be 192.168.1.33. Connect to one of the LAN ports and hold the
WPS Button while booting. After a few seconds the NBG6616 will look for
a image file called 'ras.bin' and flash it.

Return to vendor firmware is possible by resetting the bootcmd:
setenv bootcmd run boot_flash
saveenv
and flashing the vendor image via the TFTP method as described above.

Accessing the U-Boot Shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|    Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

| NBG6616> ?
| ATEN	x,(y)     set BootExtension Debug Flag (y=password)
| ATSE	x         show the seed of password generator
| ATSH	          dump manufacturer related data in ROM
| ATRT	(x,y,z,u) ATRT RAM read/write test (x=level, y=start addr, z=end addr, u=iterations
| ATGO	          boot up whole system
| ATUR	x         upgrade RAS image (filename)

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

| NBG6616> ATSE NBG6616
| 00C91D7EAC3C

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

| # bash ./tool.sh 00C91D7EAC3C
| ATEN 1,10FDFF5

Copy and paste the result into the shell to unlock zloader.

| NBG6616> ATEN 1,10FDFF5

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

| NBG6616> ATGU
| NBG6616#

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[move keys to DTSI, adjust usb_power DT label, remove kernel config
change, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 18:37:43 +02:00
Adrian Schmutzler
d4ac0ad543 treewide: make dependency on kmod-usb-net selective
A bunch of kernel modules depends on kmod-usb-net, but does not
select it. Make AddDepends/usb-net selective, so we can drop
some redundant +kmod-usb-net definitions for DEVICE_PACKAGES.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:54:30 +02:00
Nicholas Smith
c00b8dcf72 ath79: add support for Telco T1
Description:
    2x 100Mbps Etherent ports
    24V passive PoE
    64MB RAM
    16MB Flash
    2.4GHz WiFi
    1x WiFi antenna (RP-SMA connector)
    1x LTE antenna (SMA connector)
    Sierra Wireless MC7430 LTE modem

Flash instructions:
    Original firmware is based on OpenWrt.
    Flash using sysupgrade -n

SUPPORTED_DEVICES is added to support factory firmware.

Signed-off-by: Nicholas Smith <nicholas.smith@telcoantennas.com.au>
[add missing led_rssi0 DT label, add SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:49:29 +02:00
Aleksander Jan Bajkowski
37df722266 ath79: increase spi frequency on TL-WDR3500/3600/4300/4310
SPI Flash chip supports up to 33 MHz wihout fast read opcode.
Available frequencies are 112.5, 56.25, 37.5, 28.125, 22.5 etc.
This patch increases the nominal maximum frequency to 33 MHz,
reaching an effective increase from 22.5 to 28.125 MHz.

Formula to calculate SPI frequency:
Freq = 225 MHz / 2 / div

Before:

$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 3.58s
user	0m 0.00s
sys	0m 3.57s

After:

$ time dd if=/dev/mtd1 of=/dev/null bs=8M
0+1 records in
0+1 records out
real	0m 2.95s
user	0m 0.00s
sys	0m 2.93s

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:43:37 +02:00
Adrian Schmutzler
04b99d9539 ramips/mt7628: fix portmap based on board.d port assignment
When comparing to the port assignment in board.d/02_network, a few
devices seem to use the wrong setup of mediatek,portmap.

The corrects the values for mt76x8 subtarget based on the location
of the wan port.

A previous cleanup of obviously wrong values has already been done in
7a387bf9a0 ("ramips: mt76x8: fix bogus mediatek,portmap")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 12:33:38 +02:00
Andreas Böhler
ab74def0db ath79: add support for TP-Link TL-WPA8630P v2
The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC
and 2.4GHz and 5GHz WiFi modules.

Specifications
--------------

  - QCA9563 750MHz, 2.4GHz WiFi
  - QCA9888 5GHz WiFi
  - 8MiB SPI Flash
  - 128MiB RAM
  - 3 GBit Ports (QCA8337)
  - PLC (QCA7550)

MAC address assignment
----------------------

WiFi 2.4GHz and LAN share the same MAC address as printed on the label.
5GHz WiFi uses LAN-1, based on assumptions from similar devices.

LAN Port assignment
-------------------

While there are 3 physical LAN ports on the device, there will be 4
visible ports in OpenWrt. The fourth port (internal port 5) is used
by the PowerLine Communication SoC and thus treated like a regular
LAN port.

Versions
--------

Note that both TL-WPA8630 and TL-WPA8630P, as well as the different
country-versions, differ in partitioning, and therefore shouldn't be
cross-flashed.

This adds support for the two known partitioning variants of the
TL-WPA8630P, where the variants can be safely distinguished via the
tplink-safeloader SupportList. For the non-P variants (TL-WPA8630),
at least two additional partitioning schemes exist, and the same
SupportList entry can have different partitioning.
Thus, we don't support those officially (yet).

Also note that the P version for Germany (DE) requires the international
image version, but is properly protected by SupportList.

In any case, please check the OpenWrt Wiki pages for the device
before flashing anything!

Installation
------------

Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.

Additional thanks to Jon Davies and Joe Mullally for bringing
order into the partitioning mess.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[minor DTS adjustments, add label-mac-device, drop chosen, move
common partitions to DTSI, rename de to int, add AU support strings,
adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk,
adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-10 11:48:08 +02:00
Daniel Golle
cfe235c436 kernel: modules: add package kmod-iosched-bfq
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-10 09:52:31 +01:00
Christoph Krapp
982c1f6e42 ar71xx: change u-boot-env to read-write for ZyXEL NBG6616
As the ath79 port of this device uses a combined kernel + root
partition the uboot bootcmd variable needs to be changed. As using
cli/luci is more convenient than opening up the case and using a uart
connection, lets unlock the uboot-env partition for write access.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2020-08-09 23:57:17 +02:00
Felix Fietkau
5d8fded26a kernel: add missing config symbols
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-09 14:01:52 +02:00
Adrian Schmutzler
e81e625ca3 treewide: add sysupgrade comment for early DSA-adopters
Add a specific comment for early DSA-adopters that they can keep
their config when prompted due to compat-version increase.

This is a temporary solution, the patch should be simply reverted
before any release.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 20:56:12 +02:00
Adrian Schmutzler
372529d311 ath79: add support for TP-Link TL-WA901ND v3
This ports support for the TL-WA901ND v3 from ar71xx to ath79.
Most of the hardware is shared with the TL-WA850/860RE v1 range
extenders. It completes the TL-WA901ND series in ath79.

Specifications:
  Board: AP123 / AR9341
  Flash/RAM: 4/32 MiB
  CPU: 535 MHz
  WiFi: 2.4 GHz b/g/n
  Ethernet: 1 port (100M)

Flashing instructions:
  Upload the factory image via the vendor firmware upgrade option.

This has not been tested on device, but port from ar71xx is
straightforward and the device will be disabled by default anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 20:40:48 +02:00
Ansuel Smith
df3ad130d5 ipq806x: replace patches with upstream version
Replace all the custom patches with the backported upstream version

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 18:07:17 +02:00
Adrian Schmutzler
4f1a51f438 ath79: drop redundant kmods-leds-gpio
The ath79 target has CONFIG_LEDS_GPIO=y set in kernel config, so
no need to pull the kmod-leds-gpio module for specific devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
1eac573b53 ramips: mt7621: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
broken upgrade between swconfig and DSA for ramips' mt7621 subtarget.

In order to make the situation more transparent for the user, and
to prevent large switch-cases for devices, it is more convenient to
have the entire subtarget 1.1-by-default. This means that new devices
will be added with 1.1 from the start, but in contrast we don't need
to switch them in board.d files. Apart from that, users that manually
backport devices to 19.07 with swconfig will have an equivalent
upgrade experience to officially supported devices.

Since DSA support on mt7621 is out for a while already, this applies
the same uci-defaults workaround for early adopters as already
done for kirkwood and mvebu in previous commits.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
86c89bf5e8 kirkwood: fix sysupgrade experience for early DSA-adopters
Conceptually, the compat-version during sysupgrade is meant to
describe the config. Therefore, if somebody starts with a device on
19.07 and swconfig, and that person does a forceful upgrade into a
DSA-based firmware without wiping his/her config, then the local
compat-version should stay at 1.0 according to the config present
(and not get updated).

However, this poses a problem for those people that early-adopted
DSA in master, as they already have adjusted their config for DSA,
but it still is "1.0" as far as sysupgrade is concerned. This can
be healed by a simple

   uci set system.@system[0].compat_version="1.1"
   uci commit system

But this needs to be applied _after_ the upgrade (as the "old" fwtool
on the old installation does not know about compat_version) and it
requires access via SSH (i.e. no pure GUI solution is available for
this group of people, apart from wiping their config _again_ for
no technical reason). Despite, the situation will not become
obvious to those just upgrading via GUI, they will just have the
experience of a "broken upgrade".

This is a conflict which cannot be resolved by achieving both goals,
we have to decide to either keep the strict concept or improve the
situation for early adopters.

In this patch, we address the issue by providing a uci-defaults
script that will raise the compat_version for _all_ people upgrading
into a 1.1 image, no matter whether they have reset config or not.
The idea is to implement this as a _temporary_ solution, so early
adopters can upgrade into the new mechanism without issues, and
after a few weeks/months we could remove the uci-defaults script
again.

If we e.g. remove the script just before 20.xx.0-rc1, early adopters
should have moved on by then, and existing stable users would still
get the intended experience.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
a9703db720 mvebu: fix sysupgrade experience for early DSA-adopters
Conceptually, the compat-version during sysupgrade is meant to
describe the config. Therefore, if somebody starts with a device on
19.07 and swconfig, and that person does a forceful upgrade into a
DSA-based firmware without wiping his/her config, then the local
compat-version should stay at 1.0 according to the config present
(and not get updated).

However, this poses a problem for those people that early-adopted
DSA in master, as they already have adjusted their config for DSA,
but it still is "1.0" as far as sysupgrade is concerned. This can
be healed by a simple

   uci set system.@system[0].compat_version="1.1"
   uci commit system

But this needs to be applied _after_ the upgrade (as the "old" fwtool
on the old installation does not know about compat_version) and it
requires access via SSH (i.e. no pure GUI solution is available for
this group of people, apart from wiping their config _again_ for
no technical reason). Despite, the situation will not become
obvious to those just upgrading via GUI, they will just have the
experience of a "broken upgrade".

This is a conflict which cannot be resolved by achieving both goals,
we have to decide to either keep the strict concept or improve the
situation for early adopters.

In this patch, we address the issue by providing a uci-defaults
script that will raise the compat_version for _all_ people upgrading
into a 1.1 image, no matter whether they have reset config or not.
The idea is to implement this as a _temporary_ solution, so early
adopters can upgrade into the new mechanism without issues, and
after a few weeks/months we could remove the uci-defaults script
again.

If we e.g. remove the script just before 20.xx.0-rc1, early adopters
should have moved on by then, and existing stable users would still
get the intended experience.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-08 16:13:51 +02:00
Sungbo Eo
de78747de1 ramips: use lzma-loader for RT5350F-OLinuXino devices
The bootloader fails to extract a big kernel, e.g. v5.4 kernel image
with ALL_KMODS enabled. This can be fixed by using lzma-loader.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-08 16:13:51 +02:00
Sungbo Eo
a40ddc2195 ramips: adjust LZMA_TEXT_START for 32MB RAM devices
Currently the lzma-loader is placed in RAM at 32MB offset, which does not
make sense for devices with only 32MB RAM. If we adjust LZMA_TEXT_START to
24MB offset, then the lzma-loader can be used on those devices and still
about 24MB memory will be available for uncompressed image, which should be
enough for most use cases.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-08 16:13:51 +02:00
Adrian Schmutzler
1634461bd2 ramips: switch rt288x subtarget to kernel 5.4
The sbutarget has testing support for kernel 5.4 for quite a while
and builds fine, however, only one devices there is > 4 MiB.

Since it's unlikely to get a Tested-by for that device, and the other
ralink subtargets appear to be working with 5.4 so far, let's set
this target to 5.4 by default as well.

That way, even if the device happens to break, we'll still have at
least usable SDK and IB for people to use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-07 14:51:20 +02:00
Adrian Schmutzler
7c07a0f4c3 ramips/mt7620: fix portmap based on board.d port assignment
When comparing to the port assignment in board.d/02_network, many
devices seem to use the wrong setup of mediatek,portmap.

The corrects the values for mt7620 subtarget based on the location
of the wan port.

A previous cleanup of obviously wrong values has already been done in
d3c0a94405 ("ramips: mt7620/mt7621: remove invalid mediatek,portmap")

Cc: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-07 13:01:18 +02:00
Adrian Schmutzler
121c021989 ramips: invert wpad selection for mt7621
For ramips/mt7621, the wpad-basic package is not selected by default,
but added for every device individually as needed.

While this might be technically correct if the SoC does not come with
a Wifi module, only 18 of 97 devices for that platform are set up
_without_ wpad-basic currently.

Therefore, it seems more convenient to add wpad-basic by default for
the subtarget and then just remove it for the 18 mentioned devices,
instead of having to add it for about 60 times instead.

This would also match the behavior of the 5 other subtargets, where
wpad-basic/wpad-mini is added by default as well, and thus be more
obvious to developers without detailed SoC knowledge.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-07 12:02:19 +02:00
Álvaro Fernández Rojas
24f7ae814a bcm63xx: add missing endif board comnents
This provides better context for board patches.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 11:09:06 +02:00
Álvaro Fernández Rojas
0c109df7f0 bcm63xx: merge RTA770BW and RTA770W board patches
The only difference between both boards is the DSL annex.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
eddf863650 bcm63xx: add missing fallback SPROMs
A couple of SPROM IDs are missing.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
fb589b6142 bcm63xx: add missing OHCI nodes
All boards with EHCI enabled should also have OHCI enabled.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
440d5996ef bcm63xx: remove invalid EHCI nodes
There's no EHCI controller on BCM6348.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Álvaro Fernández Rojas
81fdb4235e bcm63xx: refactor board patches
Current board patches format is crazy.
Let's try to put some order.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-07 10:34:31 +02:00
Adrian Schmutzler
7673df7994 ramips: switch rt3883 subtarget to kernel 5.4
The target has testing support for kernel 5.4 for quite a while,
compiles fine for all devices, and has been run-tested on Asus
RT-N56U successfully.

Let's set it to kernel 5.4 by default to increase the audience
before an 20.xx stable branch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com> [Asus RT-N56U]
2020-08-06 23:52:57 +02:00
Álvaro Fernández Rojas
92727a1228 bcm63xx: switch to upstream CFE version detection patch
The patch improving CFE version detection has been merged (linux 5.9).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 23:06:12 +02:00
Álvaro Fernández Rojas
f41a40001a bcm63xx: switch to upstream endif comments patch
This allows better context for board patches and we no longer need a
downstream patch for that.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 23:06:12 +02:00
Álvaro Fernández Rojas
9fb1d4ce8a bcm63xx: switch to upstream LED patch
The patch adding support for the second LED HW blinking interval has been
merged (linux 5.9).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-08-06 23:06:12 +02:00
Daniel Golle
728a0c68d1 Revert "procd: update to git HEAD"
This reverts commit e0e607f0d0.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-06 16:17:37 +01:00
Davy Hollevoet
394f54ee62 ath79/nand: add support for Netgear WNDR4300TN
This patch adds support for the WNDR4300TN, marketed by Belgian ISP
Telenet. The hardware is the same as the WNDR4300 v1, without the
fifth ethernet port (WAN) and the USB port. The circuit board has
the traces, but the components are missing.

Specifications:
* SoC: Atheros AR9344
* RAM: 128 MB
* Flash: 128 MB NAND flash
* WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz)
* Ethernet: 4x 1000Base-T
* LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS
* UART: on board, to the right of the RF shield at the top of the board

Installation:

* Flashing through the OEM web interface:
  + Connect your computer to the router with an ethernet cable and browse
    to http://192.168.0.51/
  + Log in with the default credentials are admin:password
  + Browse to Advanced > Administration > Firmware Upgrade in the Telenet
    interface
  + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img
  + Proceed with the firmware installation and give the device a few
    minutes to finish and reboot.

* Flashing through TFTP:
  + Configure your wired client with a static IP in the 192.168.1.x range,
    e.g. 192.168.1.10 and netmask 255.255.255.0.
  + Power off the router.
  + Press and hold the RESET button (the factory reset button on the bottom
    of the device, with the gray circle around it, next to the Telenet logo)
    and turn the router on while keeping the button pressed.
  + The power LED will start flashing orange. You can release the button
    once it switches to flashing green.
  + Transfer the image over TFTP:
    $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img

Signed-off-by: Davy Hollevoet <github@natox.be>
[use DT label reference for adding LEDs in DTSI files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Shibajee Roy
a673ac66fa ramips: add support for Netgear JWNR2010 v5
Specification:
 - CPU: MediaTek MT7620N (580 MHz)
 - Flash size: 4 MB NOR SPI
 - RAM size: 32 MB DDR1
 - Bootloader: U-Boot
 - Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz)
 - Switch: MT7620 built-in 10/100 switch with vlan support
 - Ports: 4x LAN, 1x WAN
 - Others: 7x LED, Reset button, UART header on PCB (57600 8N1)

Flash instructions:
 1. Use ethernet cable to connect router with PC/Laptop, any router
    LAN port will work.
 2. To flash openwrt we are using nmrpflash[1].
 3. Flash commands:
      First we need to identify the correct Ethernet id.

        nmrpflash -L

        nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img

      This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.)

 4. Now remove the power cable from router back side and immediately connect it again.
    You will see flash notification in CMD window, once it says reboot the device just
    plug off the router and plug in again.

Revert to stock:
 1. Download the stock firmware from official netgear support[2].
 2. Follow the same nmrpflash procedure like above, this time just use the stock firmware.

        nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img

MAC addresses on stock firmware:
LAN = *:28 (label)
WAN = *:29
WLAN = *:28

On flash, the only valid MAC address is found in factory 0x4.

Special Note:
 This openwrt firmware will also support other netgear N300 routers like below as they
 share same stock firmware[3].
 JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050

[1] https://github.com/jclehner/nmrpflash
[2] https://www.netgear.com/support/product/JWNR2010v5.aspx
[3] http://kb.netgear.com/000059663

Signed-off-by: Shibajee Roy <ador250@protonmail.com>
[create DTSI, use netgear_sercomm_nor, disable by default, add MAC
addresses to commit message, add label MAC address]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Adrian Schmutzler
a66449c608 ramips: drop remaining m25p,chunked-io from DTS
This option was a spi nor hack which is dropped in commit bcf4a5f474
("ramips: remove chunked-io patch and set spi->max_transfer_size instead")

Most of it has already been removed in
be2b61e4f1 ("ramips: drop m25p,chunked-io from dts")

It seems all current usages were added after that. Remove them.

Cc: Chuanhong Guo <gch981213@gmail.com>
Reported-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Adrian Schmutzler
3b89849b57 ramips: add common definition netgear_sercomm_nor
Like NAND-based devices, SPI-NOR based Netgear devices also share
a common setup for their images. This creates a common defition
for them in image/Makefile, so it can be reused across subtargets.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:06 +02:00
Daniel Golle
e0e607f0d0 procd: update to git HEAD
47a9f0d service: add method to query available container features
 afbaba9 initd: attempt to mount cgroup2
 ead60fe jail: use pidns semantics also for timens
 759e9f8 jail: make use of BLOBMSG_CAST_INT64 for OCI rlimits
 83053b6 instance: add instances into unified cgroup hierarchy
 16159bb jail: parse OCI cgroups resources

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-08-06 15:27:51 +01:00
Adrian Schmutzler
77e850fe76 ramips: tidy up MAC address setup for Linkit Smart and Omega2
Linkit Smart 7688 and Onion Omega 2(+) are one-port devices, and
have their port set to LAN by default. Setting up a WAN MAC address
for them doesn't make any sense, as no wan interface will be created
in uci config. Despite, these devices also set lan_mac in 02_network,
although mtd-mac-address sets a different address for the ethernet
interface in DTS.

Clean this up by moving the lan_mac value into DTS and dropping the
entries in 02_network completely. That way, the effective address
on the LAN interface should stay the same, but we get rid of the
extra (re)assignments.

As I don't have access to the devices, this does not tell anything
about whether 0x2e is actually a good choice, it just preserves
the existing assignment.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 13:33:26 +02:00
Tobias Welz
633ea0db0f ramips: WizFi630S use macs from factory partion
WIZnet WizFi630s has three mac addresses in the factory partition:
0x04 (also on the label), 0x28 for wan mac and 0x2e as lan mac.
All three macadresses are sequential series of addresses.
This is making use of them.

While at it, also add the label MAC address to 02_network.

MAC addresses as verified by OEM firmware:

use      interface   source
WLAN     ra0         factory 0x04 (label)
WAN      eth0.2      factory 0x28 (label + 1)
LAN      eth0.1      factory 0x2e (label + 2)

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[fix sorting in 02_network, commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 13:33:26 +02:00
Tobias Welz
d0b229f553 ramips: correct WizFi630S pin mappings
WizFi630S had some pins changed in the release version of the board.
The run led, wps button and a slide switch where affected.
This patch is correcting this.
i2c is removed as it is sharing a pin with the run (system) led.
uart2 is enabled as it is also enabled in the OEM firmware.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-06 13:33:26 +02:00
Adrian Schmutzler
d1db1f4240 ipq40xx: refresh kernel 5.4 config
Refresh config with make kernel_oldconfig.

After d1a8217d87 ("kernel: clean-up build-configurable kernel
config symbols"), the routine wants to add an additional
CONFIG_CGROUPS (=n), which has been removed manually again, as
this seems unintended.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 12:51:51 +02:00
Felix Fietkau
431b177afa mediatek: fix mt7622-rfb1 board support
Make GPIO keys active-low.
Add DSA support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:42:43 +02:00
Felix Fietkau
b0f7ea2853 kernel: unify CONFIG_GPIO_SYSFS in kernel configs
Enable it for all platforms

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:37:04 +02:00
Alexey Dobrovolsky
4c73c34ec4 ramips: switch rt305x subtarget to kernel 5.4
RT3x5x seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.

Since 4 of 6 targets are on kernel 5.4 now, invert the kernel
version setup logic in Makefile/target.mk files.

Tested on ZyXEL Keenetic.

Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[invert version setup logic]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:27:35 +02:00
Tobias Welz
816973f42a ramips: enable flashing WizFi630S via OEM firmware
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 23:08:03 +02:00
Adrian Schmutzler
7c1c0a00fc ipq806x: use qcom-ipq8064-v1.0.dtsi from upstream
This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches
instead of keeping a local version. As a consequence:

- we use a part of the shared definitions there and update device
  DTS files accordingly
- we move additional stuff from our local v1.0.dtsi to the patch
- we drop partitions, LEDs and keys from the file as we will
  implement them differently anyway

Like with the previous patch, this follows the idea that a diff
from upstream might be easier to handle than a big file of our
own with different distribution pattern of properties.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:08:03 +02:00
Adrian Schmutzler
b7b7c2a6ad ipq806x: use qcom-ipq8064.dtsi from upstream
Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite
it with a full version of our own in the ipq806x target. About half of
the contents of our file are upstream content, the other half are local
improvements.

To prevent us from having a lot of code maintained twice in parallel,
this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our
local changes are arranged into three patches, the first pulling a
commit from upstream, the second doing a few small adjustments, and
the third adding all additional stuff.

This should get us the best of both worlds.

The property "ports-implemented" on sata@29000000 is moved to
2nd-level DTSI files as kernel defines it there as well.

While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to
include the kernel version where it's added upstream.

Even though this might look more complicated in the first place,
the aim is to bring our files closer to upstream, so we can benefit
from changes directly and vice-versa. After all, this drop about
650 lines just copied from the upstream DTSI file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-05 23:08:03 +02:00
Tobias Welz
b735bbcb18 ramips: remove doublet entry in WizFi630S dts file
&wmac entry in WIZnet WizFi630S dts file was existing two times.
This is removing one of them.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 12:10:15 +02:00
Tobias Welz
36d4c2272e ramips: disable unused phy ports of WizFi630S
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
2020-08-05 12:10:15 +02:00
Rafał Miłecki
e47bec489f bcm47xx: switch to kernel 5.4
Switch, LEDs, USB, buttons, sysupgrade testedon BCM4706.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 15:51:08 +02:00
Rafał Miłecki
7125323b81 bcm53xx: switch to kernel 5.4
Switch, USB, WiFi, buttons tested on BCM47094.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:28:56 +02:00
Rafał Miłecki
36c53e0dd2 bcm53xx: set HW_RANDOM_BCM2835=y
This enables Random Number Generator support on Northstar (described in
DT with brcm,bcm5301x-rng).

It's also a workaround for OpenWrt bug with kernel config causing:
Broadcom BCM2835/BCM63xx Random Number Generator support (HW_RANDOM_BCM2835) [Y/n/m/?] (NEW)

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Rafał Miłecki
c8c9876607 bcm53xx: update kernel 5.4 DTS to upstream 5.9 state
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Rafał Miłecki
b9cd55b88e bcm53xx: update kernel 5.4 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2020-08-04 13:27:19 +02:00
Richard Fröhning
009e62c92c ramips: add support for TP-Link RE200 v3
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button

Unverified:
- UART header on PCB (57600 8n1)

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

MAC address assignment has been done according to the RE200 v2.

The label MAC address matches the OpenWrt ethernet address.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Recovery
--------

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.

Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 23:34:34 +02:00
Adrian Schmutzler
1deaf695ec ramips: fix/tidy up 4M tplink-v2-image flash layouts
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:

device         uboot    OEM firmware  OpenWrt (incl. config)
tl-wr840n-v5   0x20000  0x3c0000      0x3d0000
tl-wr841n-v14  0x10000  0x3d0000      0x3e0000

In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.

However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.

So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 12:17:08 +02:00
Adrian Schmutzler
18b7d87a8f kirkwood: get rid of BOARD_NAME and tidy up DEVICE_DTS
Since most of the DTS file names follow a common scheme now, let's
update the automatically generated DEVICE_DTS value and get rid
of some DEVICE_DTS and all BOARD_NAME entries for individual devices.

This should specifically make the job easier for developers adding
new devices, as they are not tempted to copy over BOARD_NAME anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:47:22 +02:00
Adrian Schmutzler
356866c481 target: replace remaining occurrences of ifconfig with ip
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.

Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:42:04 +02:00
Sungbo Eo
c90db26e05 ar71xx: restore support for boot console with arbitrary baud rates
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 18:10:06 +02:00
Sungbo Eo
a5e404d192 ar71xx: enable ethernet LED of Arduino Yun
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.

Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
58dc1d0637 ar71xx: fix sysupgrade for Arduino Yun
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.

Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
43896dc0b0 Revert "ar71xx: fix Arduino Yun enabling of level shifters outputs"
This reverts commit 077253dd66.

The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Adrian Schmutzler
8a8ef4ed86 ath79/mikrotik: create shared device definitions for nor and nand
Move the image preparation and nand-utils package selection into
common device definitions for NOR/NAND devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-01 18:31:24 +02:00
Stijn Tintel
5c3e83fa88 kernel: fix missing TRANSPARENT_HUGEPAGE symbols
Enabling KERNEL_TRANSPARENT_HUGEPAGE exposes 2 missing symbols:
* CONFIG_READ_ONLY_THP_FOR_FS
* TRANSPARENT_HUGEPAGE_ALWAYS
* TRANSPARENT_HUGEPAGE_MADVISE

The first one was added in 5.4, and is marked experimental there so just
disable it in the generic config.

For the latter two, we should not force the user to use either of them,
so add them as build-configurable kernel options.

Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-08-01 14:33:46 +01:00
Stijn Tintel
1bff9f5b78 kernel: add missing config symbol
This symbol is exposed on ARM64 with EFI enabled in the kernel config.
Currently this happens only on ipq807x, but as there might be new ARM64
targets with EFI in the future it is better to add the symbol to the
generic config.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2020-08-01 15:19:11 +03:00
Linus Walleij
9e02580d52 gemini: Add swap partition to DNS-313
Sometimes when using the DNS-313 memory usage can peak and
with a simple swap partition we can avoid running into the
roof and invoking the OOM killer. Set this partition to
128MB (twice the size of the memory of the DNS-313).

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-31 18:34:40 +02:00
Christian Lamparter
caa6ada969 apm821xx: disable WNDR4700 5.4 image
The compressed image that the buildbots are building is too large for
the netgear uboot and it crashes and soft-bricks the device.

| Uncompressing Kernel Image ...
| LZMA: uncompress or overwrite error 1 - must RESET board to recover

The whole target likely needs to be switched zImage which is a major
hassle due to powerpc's legacy bootwrapper setup as compared to ARM.
So for now, disable the device.

Reported-by: Wiktor Stasiak (FS#3258)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-07-31 18:17:34 +02:00
Adrian Schmutzler
65305cb448 kirkwood: use real model names for Linksys devices
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.

As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 15:03:43 +02:00
Tony Ambardar
a4856dab0d kernel: mips: restore missing MIPS32 cBPF JIT
Kernel v5.1 included an eBPF JIT for MIPS32 kernels, but problems were
discovered [1] and the changes later reverted in kernel v5.5 with commits:

  * f8fffebdea75 ("MIPS: BPF: Disable MIPS32 eBPF JIT")
  * 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT")

Only the first of these was backported to LTS kernel 5.4, leaving cBPF
programs without a JIT and introducing a performance regression for any
such users e.g. libpcap, tcpdump, etc.

Restore cBPF performance by backporting the second commit above:
  * 070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch

[1] https://lore.kernel.org/bpf/20191205182318.2761605-1-paulburton@kernel.org/

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-07-31 13:42:14 +01:00
Adrian Schmutzler
664237deaa mvebu: fix alphabetic sorting in 02_network
This has been overlooked when removing solidrun,clearfog-a1 entry.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
e496eefccc mvebu: increase compat version for SolidRun ClearFog Base
When changing the Pro variant to DSA, the ethernet interface rename
script was dropped by all devices to keep them in sync:

  be309bfd74 ("mvebu: drop 06_set_iface_mac preinit script")

Therefore, network config will be broken after upgrade for the
Base variant as well. Increase the compat version and provide a
message to signal that to the users.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
090779b24e kirkwood: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for kirkwood.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Since we never removed SUPPORTED_DEVICES for this target, we don't
have to add it back either.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
494f12c52d mvebu: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for mvebu.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES
that have been removed in previous patches to prevent broken config.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Robinson Wu
84cb0f7ace ramips: add support for JS76x8 series DEV boards
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:

- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
       3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)

Installation via OpenWrt:

The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.

Installation via U-boot web:

1. Power on board with reset button pressed, release it
   after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.

Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
   on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (192.168.1.8) ==:192.168.1.8
   Input server IP (192.168.1.123) ==:192.168.1.123
   Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.

Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
David Bauer
ced167d729 ramips: limit 5GHz channels for RAVPower RP-WD009
When selecting a channel below 100 on the 5GHz radio, the channel will
be detected as busy all the time.

Survey data from wlan1
	frequency:			5240 MHz [in use]
	channel active time:		165729 ms
	channel busy time:		158704 ms
	channel transmit time:		0 ms

Channels 100 and above work fine:

Survey data from wlan1
	frequency:			5500 MHz
	channel active time:		133000 ms
	channel busy time:		21090 ms
	channel transmit time:		0 ms

Limit the available channels, so users do not have the impression
their device is broken.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-30 22:33:53 +02:00
Petr Štetiar
e9f7923a1d treewide: mark devices as BROKEN instead of commenting out
This adds the newly introduced BROKEN flag to a bunch of devices
that previously just had TARGET_DEVICES commented out. By this, we
can select them in make menuconfig when BROKEN developer config option
is selected, instead of having to edit the code.

In contrast to DEFAULT := n, this is meant to cover devices that
don't boot or don't compile at all.

ath25: np25g, wpe53g
  both disabled during kernel bump 3.18->4.4 without reason given
  f89a20a89a ("ath25: update kernel from 3.18 to 4.4")

bcm53xx: linksys-ea6300-v1, linksys-ea9200, linksys-ea9500
  broken due to insufficient/broken TRX support
  55ff15cfd5 ("bcm53xx: disable building Linksys EA6300 V1 image")
  cd0f9900a4 ("bcm53xx: parepare for building more Linksys images")

bcm63xx: tplink-archer-c5-v2, tplink-archer-c9-v1
  disabled when kernel 5.4 support was added, probably broken
  50c6938b95 ("bcm53xx: add v5.4 support")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, use BROKEN, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:49:22 +02:00
Petr Štetiar
504000d520 treewide: use DEFAULT := n to disable non-broken devices
This uses DEFAULT := n on a bunch of devices that previously were
"disabled" by commenting out TARGET_DEVICES. This will allow to
build them without having to modify the code, but they will not
be selected for default build or buildbots.

The change is applied to all devices that are not "broken", but suffer
from image site limitations or similar, or have been added in the past
but never confirmed to run on the device properly:

at91: at91-q5xr5:
  kernel image too big
  31aeae0774 ("at91: do not build image for at91-q5xr5")

bcm47xx: asus-rt-ac66u:
  disabled since it was added in 2015
  69aefc771f ("brcm47xx: build images for Asus devices")

bcm47xx: netgear-wndr3400-vcna, netgear-wnr3500u, netgear-wnr3500-v2-vc
  added disabled in 2012, but never confirmed to work on devices
  5dec9dd3b2 ("brcm47xx: add code to generate images for some netgear
    devices")

bcm53xx: netgear-r8500
  added disabled: "start working on Netgear R8500"
  3b76c7cf0b ("bcm53xx: start working on Netgear R8500")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:48:38 +02:00
Adrian Schmutzler
bf5c56ba57 ath79: cosmetic fixes for partition node of D-Link DIR-825 B1
Make the node name match the reg property and remove the unused
DT label.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:43:56 +02:00
Daniel Golle
d1a8217d87 kernel: clean-up build-configurable kernel config symbols
Don't explicitely disable options in target/linux/generic/config-* if
they are already controlled in config/Config-kernel.in.
Add a bunch of new symbols  and prepare defaults for using only unified
hierarchy (ie. cgroup2). Update symbol dependencies while at it

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-07-30 16:59:47 +01:00
Luochongjun
68ac3f2cdd ath79: add support for gl-e750
The gl-e750 is a portable travel router that gives you safe access to
the internet while traveling.

Specifications:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB DDR2
- Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
- Ethernet: 10/100: 1xLAN
- Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- OLED Screen: 128*64 px

MAC addresses based on vendor firmware:
LAN *:a0 art 0x0
2.4GHz *:a1 art 0x1002
5GHz *:a2 art calculated from art 0x0 + 2

Flash firmware:
Since openwrt's kernel already exceeds 2MB, upgrading from the official
version of GL-inet (v3.100) using the sysupgrade command will break the
kernel image. Users who are using version 3.100 can only upgrade via
uboot. The official guidance for GL-inet is as follows:
https://docs.gl-inet.com/en/3/troubleshooting/debrick/

In the future, GL-inet will modify the firmware to support the sysupgrade
command, so users will be able to upgrade directly with the sysupgrade
command in future releases.

OLED screen control:
OLED controller is connected to QCA9531 through serial port, and can send
instructions to OLED controller directly through serial port.
Refer to the links below for a list of supported instructions:
https://github.com/gl-inet/GL-E750-MCU-instruction

Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
[fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 20:49:48 +02:00
Adrian Schmutzler
6da5356195 lantiq: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for all devices with 4M flash on lantiq.
Note that this will affect _all_ devices for amazonse ("ase") and
xway_legacy subtarget.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
55e2d5eb3b ath79: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for the remaining devices with 4M flash
on ath79. Note that this will leave exactly one enabled device for
ath79/tiny subtarget, PQI Air-Pen, which was moved there due to
kernel size restrictions.

All 4M TP-Link devices have already been disabled in
8819faff47 ("ath79: do not build TP-Link tiny images by default")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
01a3e891d7 ath79: reorganize common image definitions for Netgear
Netgear currently has a special definition for tiny devices, which
is only used by two devices. Despite, it sets ups the IMAGE/default
definition individually for all devices, although there is actually
only one exception.

This merges the common parts into a single netgear_generic definition
(in contrast to netgear_ath79_nand), and adjusts the individual
definitions accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
David Bauer
c5360894dc rockchip: enable rockchip-thermal
Enable the rockchip-thermal driver to allow reading the temperature of
the SoC.

Tested on NanoPi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-29 01:40:20 +02:00
David Bauer
7a4fc8906c rockchip: distribute net interrupts
This adds a hotplug script for distributing interrupts of eth0 and eth1
across different cores. Otherwise the forwarding performance between
eth0 and eth1 is severely affected.

The existing SMP distribution mechanic in OpenWrt can't be used here, as
the actual device IRQ has to be moved to dedicated cores. In case of
eth1, this is in fact the USB3 controller.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
5a57a1ac1f arm64: dts: rockchip: Add txpbl node for RK3399/RK3328
Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue
where tx checksumming does not work with packets larger than 1498.

The default Programmable Buffer Length for TX in these GMAC's is
not suitable for MTUs higher than 1498. The workaround is to disable
TX offloading with 'ethtool -K eth0 tx off rx off' causing performance
impacts as it disables hardware checksumming.

This patch sets snps,txpbl to 0x4 which is a safe number tested ok for
the most popular MTU value of 1500.

For reference, see https://lkml.org/lkml/2019/4/1/1382.

Signed-off-by: Carlos de Paula <me@carlosedp.com>
Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
6242ac4735 rockchip: enable LAN LED configuration
This enables the LEDs on the LAN interfaces.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b7a9a183fb rockchip: add NanoPi R2S support
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.

MAC-address
-----------
The vendor code supports reading a MAC address from an EEPROM connected
via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC
address in binary at offset 0xfa. However, my two units didn't come with
such an EEPROM soldered on. The EEPROM should be placed between the SoC
and the GPIO pins on the board. (U10)

Generating rendom MAC addresses works around this issue. Otherwise, all
boards running the same image have identical MAC addresses.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b72f7c64a4 rockchip: allow for multiple boot-scripts
Add support for select a bootscript depending on the device built. This
is necessary, as the FriendlyARM NanoPi R2S needs a different bootcmd in
order to produce output on the debug UART.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
Adrian Schmutzler
bcd7a0c095 arc770: update kernel version to 5.4
Update config with make kernel_oldconfig and copy/refresh patch.

Add CONFIG_WATCHDOG_CORE=y to fix the following error as done for
several targets already:

 Package kmod-hwmon-sch5627 is missing dependencies for the following
 libraries:
 watchdog.ko

Directly switch to kernel 5.4.

This patch is compile-tested only. However, the target is essentially
pure upstream with a single patch, and it has been reported that
kernel 5.4 has been run on this target successfully already.

Note that in my local tests building with all packages/kmods failed
since openvswitch selects libunwind, which doesn't build for arc with
the following error:

checking if we should build libunwind-ptrace... yes
checking if we should build libunwind-setjmp... yes
checking for build architecture... x86_64
checking for host architecture... arc
checking for target architecture... arc
checking for target operating system... linux-gnu
checking for ELF helper width... configure: error: Unknown ELF target: arc
make[3]: *** [Makefile:65: /data/openwrt/build_dir/target-arc_arc700_uClibc/
   libunwind-1.3.1/.configured_68b329da9893e34099c7d8ad5cb9c940] Error 1

Deselecting all kmod-openvswitch* packages will have the build run through.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 20:15:10 +02:00
Adrian Schmutzler
88689da65f lantiq: fix cosmetic issues with partition offsets and sizes
This fixes a few cosmetic issues with partition offset and size
that are inconsistent probably due to copy/pasting.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 13:02:47 +02:00
Josh Bendavid
11bff24b3e ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
        WiFi 5G (white), USB 3.0 (white)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

MAC addresses:

lan   factory 0xe000     *:EB (label)
wan   factory 0xe006     *:EE
2.4   factory 0xe000 +1  *:EC
5.0   factory 0xe000 +2  *:ED

Seems like vendor didn't replace the dummy entrys in the calibration data.

Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:37:07 +02:00
Adrian Schmutzler
8126e572dd imx6: use device-tree compatible for board name
In imx6, we currently use the model from DTS to derive a board name
manually in /lib/imx6.sh.

However, if we have individual DTS files anyway, we can exploit
generic 02_sysinfo and use the compatible as board name directly.

While at it, remove the wildcards from /lib/upgrade/platform.sh as
these might make code shorter, but are quite unpleasant when grepping
for a specific device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:10:45 +02:00
Adrian Schmutzler
0f3c3a5fb2 layerscape: harmonize device strings
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.

This patch applies that scheme to the layerscape target.

Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.

Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.

While at it, remove one layer of complexity for the setup in
tfa-layerscape package.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:06:52 +02:00
Adrian Schmutzler
a1eb2c4633 mvebu: only disable WRT1900AC v1 and WRT32X for buildbots
Use "DEFAULT := n" to only disable devices for buildbots, but
keep them available for manual build.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 11:05:25 +02:00
Jo-Philipp Wich
ac9730c495 mvebu: disable WRT1900AC v1 and WRT32X images for now
The kernel appears to have grown too large, breaking the build for the
entire target.

Disable the affected images for now until the situation is dealt with.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-07-26 18:58:22 +02:00
David Woodhouse
b36422b914 mediatek: mt7623: add full system image for UniElec U7623
This adds a full eMMC image including U-Boot, which means that the
kernel can inherit the true RAM size detected by the preloader.

As implemented in previous commits, sysupgrade to this image from
the legacy layout (and via that, from the vendor-installed image)
is supported.

Rename the legacy image for the 512MiB board, for clarity.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:31 +08:00
David Woodhouse
1113dcab05 mediatek: mt7623: rename gen_banana_pi_img.sh → gen_mtk_mmc_img.sh
As I buy more hardware and continue to work on consolidation, This will
apply to a lot of MediaTek platforms; rename it accordingly.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
f5cebbe2e4 mediatek: mt7623: make gen_banana_pi_img.sh more generic
This actually covers fairly much all the MediaTek platforms; they
only have different images because they don't include the preloader
and U-Boot, and rely on preinstalled stuff from the vendor.

So this script can slowly take over the world as we complete the
support for various other platforms, starting with UniElec U7623…

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
5787684cb4 mediatek: mt7623: add scatter file for unbricking with SP Flash Tool
Many MediaTek SoCs can be unbricked by using the SP Flash Tool from
http://spflashtool.com/ along with a "scatter list" file, which is
just a text file listing which image gets loaded where.

We use a trivial partition layout for the tool, with the whole eMMC
image as a single "partition", which means users just need to unzip
the sysupgrade image. Doing the real partition layout would be overly
complex and would require the individual partitions to be shipped
as artifacts — or users to extract them out of the sysupgrade image
just for the tool to put them adjacent to each other on the eMMC
anyway.

The tool does require a copy of the preloader in order to operate,
even when it isn't flashing the preloader to the eMMC boot region.
So drop that into the bin directory as an artifact too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:07:52 +08:00
Chuanhong Guo
65fc47cac5 mediatek: mt7623: build lzma fit for bpi-r2
bpi-r2 images are shipped with mainline u-boot which can extract lzma
with no problem.
remove custom kernel recipe to build lzma fit image instead of
uncompressed fit with zboot.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-26 17:04:49 +08:00
David Woodhouse
29fa5526a2 mediatek: mt7623: prepare for full sysupgrade support on UniElec U7623
An upcoming commit will add a full system image for U7623 which will
contain the MBR partition table and U-Boot too.

That contrasts with the current image which only owns the eMMC from
sector 0xa00 onwards, and must start with a legacy uImage.

Prepare for sysupgrade to the new images, and cope with the fact that
the recovery partition will be /dev/mmcblk0p2 instead of /dev/mmcblk0p1
after the upgrade.

This commit could potentially be backported to 19.07 to allow for direct
sysupgrade to the new image layout.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
7a1eaa446b mediatek: mt7623: increase flexibility of finding recovery partition
I'm about to change the layout of the images for UniElec U7623 so make it
find the recovery partition based on which the root partition is too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
ff8cc137fb mediatek: mt7623: fix Ethernet setup for TRGMII mode
This fixes the TX performance issues seen on MT7623 boards.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
be3c8f8b2b mediatek: fix Ethernet support on UniElec U7623
The definition of the switch in the device-tree was not correct. Make it
look more like the Banana Pi R2, which works.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
David Woodhouse
6eb63019af mediatek: mt7623: fix sysupgrade from vendor OpenWrt on UniElec U7623
This board ships with an ancient 14.07-based OpenWrt using block2mtd, and
the MBR partition table contains nonsense.

It is possible to sysupgrade to an upstream OpenWrt image, but the
legacy layout of the OpenWrt images start at 0xA00 in the eMMC, with
a raw uImage. The legacy OpenWrt image doesn't "own" the beginning
of the device, including the MBR and U-Boot.

This means that when a user upgrades to upstream OpenWrt, it doesn't
boot because it can't find the right partitions. So hard-code them on
the kernel's command line using CONFIG_CMDLINE_PARTITION (for block).

Additionally, the vendor firmware doesn't cope with images larger than
about 36MiB, because it only overwrites the contents of its "firmware"
MTD partition. The current layout of the legacy image wastes a lot of
space, allowing over 32MiB for the kernel and another 10MiB for the FAT
recovery file system which is only created as 3MiB. So pull those in
to allow 4¾ MiB for the kernel, 3MiB for recovery, and then we have over
20MiB for the root file system.

This doesn't affect the new images which ship with a full eMMC image
including a different MBR layout and a partition for U-Boot, because
our modern U-Boot can actually pass the command line to the kernel, and
the built-in one doesn't get used anyway.

Tested by upgrading from vendor OpenWrt to the current legacy image,
from legacy to itself, to the previous legacy layout, and then to
finally the full-system image.

This commit probably wants backporting to 19.07, which also doesn't
install over the vendor OpenWrt and doesn't even have a full-system
installation option.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
David Woodhouse
ea9ef8c945 mediatek: mt7623: add explicit console= to U7623 kernel
The bootloader for legacy builds can't set it, so we end up unable to
log in on the serial port.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00
Leon M. George
15f585afc5 ath79: add support for Compex WPJ563
Specifications:

SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
3×3 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V passive or 36V-56V passive with optional IEEE 802.3af/at
USB 3.0 header

Installation:

To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj563-squashfs-sysupgrade.bin
erase 0x9f680000 +1
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '7A02':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj563-squashfs-cpximg-7a02.bin

MAC addresses:

<&uboot 0x2e010>  *:71  (label)
<&uboot 0x2e018>  *:72
<&uboot 0x2e020>  *:73
<&uboot 0x2e028>  *:74

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2020-07-26 02:14:45 +02:00
Aleksander Jan Bajkowski
f8ea7c53fd lantiq: xrx200: disable unused switch and phy
xrx200 has a 6 port built-in switch with 2 integrated PHY. None of the
xrx200 router uses external switch. Most boards use integrated or Lantiq
(Intel) PEF7071 PHY. Only some FritzBox routers use AT803X PHY and
VGV7510KW22 use ICPLUS PHY. Other unused PHY drivers may be removed.

This patch enables these symbols only on xway and xway_legacy subtargets:
 - CONFIG_PSB6970_PHY (Driver for PHY in PSB6970 - 7 port FE Switch)
 - CONFIG_RTL8366RB_PHY (Driver for PHY in RTL8366 - 6 port GE Switch)
 - CONFIG_RTL8366_SMI (Driver for RTL8366 - 6 port GE Switch)

Reduces image size by 7.3kB.

Continuation of 58a6f06978 (PR: #2983)

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[fix sorting in config files, small fix in commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-26 02:14:38 +02:00
Adrian Schmutzler
739d282c2f mediatek: remove condition in Device/Default
The current condition with part of the variables set dependent on
the subtarget in Device/Default isn't really nice to read and also
defeats the purpose of having a default node.

This removes the special settings for mt7623 and moves them to the
individual devices, which is not much of a problem as there are
actually just two of them and they partly use different settings
anyway.

While at it, slightly adjust the order of variables and wrap some
long lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 23:19:19 +02:00
Bjoern Dobe
d38d345c72 ath79: mikrotik: use base mac on lan for RBwAPG-5HacT2HnD
The Mikrotik RBwAPG-5HacT2HnD has only a single ethernet interface
(lan), and the vendor uses the base (label) MAC address for it.

Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
[commit title/message improvement]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 22:01:34 +02:00
Sungbo Eo
ab78694fe8 treewide: rename POWER_ON_STRIP register
AR8327 datasheet[1] calls the register at address 0x0010
"Power-on Strapping Register". As it has nothing to do with "strip",
let's rename it to "POWER_ON_STRAP" to make it easier to grasp.

[1] https://lafibre.info/images/doc/201106_spec_AR8327.pdf

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-25 21:50:50 +02:00
John Thomson
8484d6da1e ramips: remove non-existant poe_passthrough for RouterBOARD 750Gr3
This 750gr3 GPIO17 switch was added based on vendor source,
but only the 760iGS (which shares the rbsysfs board identifier)
device has the physical wiring. The 750Gr3 actually does not
support PoE out.

Apart from that, note that the gpio base (480) would have required
this GPIO to be referenced as 497 if it was kept.

Fixes: 6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:41:07 +02:00
Davide Fioravanti
92780d80ab ramips: add support for Winstars WS-WN583A6
The Winstars WS-WN583A6 is a wireless repeater with 2 gigabit ethernet
ports. Even if mine is branded as "Gemeita AC2100", the sticker on the
back says WS-WN583A6. So I will refer to it as Winstars WS-WN583A6.
Probably the real product name is the Wavlink WL-WN583A6 because of
the many references to Wavlink in the OEM firmware and bootlog.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 8MB NOR (GigaDevice GD25Q64B)
ETH:   2x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7603E (2x2:2)
  - 5GHz:   1x MT7615E (4x4:4)
  - 6 internal antennas
BTN:
  - 1x Reset button
  - 1x WPS button
  - 1x ON/OFF switch (working but unmodifiable)
  - 1x Auto/Schedule switch (working but unmodifiable. Read Note #3)
LEDS:
  - 1x White led
  - 1x Red led
  - 1x Amber led
  - 1x Blue led
  - 2x Blue leds (lan and wan port status: working but unmodifiable)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M83A6.V5030.191210 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box:
	mkdir /etc_ro/lighttpd/www/dev; for i in /dev/mtd*ro; do dd if=${i} of=/etc_ro/lighttpd/www${i}; done

3) Click "Apply"

4) After few seconds, in the textarea should appear this output:
		16384+0 records in
	16384+0 records out
	8388608 bytes (8.0MB) copied, 4.038820 seconds, 2.0MB/s
	384+0 records in
	384+0 records out
	196608 bytes (192.0KB) copied, 0.095180 seconds, 2.0MB/s
	128+0 records in
	128+0 records out
	65536 bytes (64.0KB) copied, 0.032020 seconds, 2.0MB/s
	128+0 records in
	128+0 records out
	65536 bytes (64.0KB) copied, 0.031760 seconds, 2.0MB/s
	15744+0 records in
	15744+0 records out
	8060928 bytes (7.7MB) copied, 3.885280 seconds, 2.0MB/s
	dd: can't open '/dev/mtd5ro': No such device
	dd: can't open '/dev/mtd6ro': No such device
	dd: can't open '/dev/mtd7ro': No such device

   Excluding the "X.XXXXXX seconds" part, you should get the same
   exact output. If your output doesn't match mine, stop reading
   and ask for help in the forum.

5) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd0ro
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro

   If one (or more) of these files weight 0 byte, stop reading and ask
   for help in the forum.

6) Store these downloaded files in a safe place.

7) Reboot your router to remove any temporary file from your router.

Installation
------------
Flash the initramfs image in the OEM firmware interface.
When openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) The "System Command" page allows to run every command as root.
   For example you can use "dd" and "nc" to backup the OEM firmware.
   PC (SERVER):
	nc -l 5555 > ./mtdXro
   ROUTER (CLIENT):
	dd if=/dev/mtdXro | nc PC_IP_ADDRESS 5555

2) The OEM web interface accepts only images containing the string
   "WN583A6" in the filename.
   Currently the OEM interface accepts only the initramfs image
   probably because it checks if the ih_size in the image header is
   equal to the whole image size (instead of the kernel size)
   Read more here:
   https://forum.openwrt.org/t/support-for-strong-1200/22768/19

3) The white led (namely "Smart Night Light") can be controller by the
   user only if the side switch is set to "Schedule" otherwise it will
   be activated by the light condition (there is a photodiode on the
   top side of the router)

4) Router mac addresses:

   LAN		XX:XX:XX:XX:XX:8F
   WAN		XX:XX:XX:XX:XX:90
   WIFI 2G	XX:XX:XX:XX:XX:91
   WIFI 5G	XX:XX:XX:XX:XX:92

   LABEL	XX:XX:XX:XX:XX:91

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove chosen node, fix whitespace]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:04:11 +02:00
Adrian Schmutzler
1e55df2e41 oxnas: use vendor_model scheme for ox810se
Most newer targets have been converted to consistently use
vendor_model scheme for device definitions/image names, ox820 is
using it as well, so let's just convert ox810se for consistency.

While at it, use generic setup for DEVICE_DTS and add SUPPORTED_DEVICES.
The latter have been introduced for ox820 already in
cf7896117b ("oxnas: enable image metadata by setting SUPPORTED_DEVICES")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-25 21:04:11 +02:00
Hauke Mehrtens
64de3076c3 lantiq: Fix warning in SPI driver
This fixes a warning in the SPI driver at bootup. This warning is seen
in kernel 5.4 on lantiq deives.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-23 23:39:56 +02:00
Phi Nguyen
eda9751d86 ipq40xx: support reset button for WPJ419
Compex WPJ419 has a reset button on a GPIO pin.

Signed-off-by: Phi Nguyen <phind.uet@gmail.com>
2020-07-23 12:56:58 +02:00
Adrian Schmutzler
b057862e24 Revert "ramips: fix flash layout for TP-Link TL-WR841N v14"
This reverts commit 1623defbdb.

As already stated in the reverted patch, the OEM firmware will
properly recreate the config partition if it is overwritten by
OpenWrt.

The main reason for adding the partition was the image size
restriction imposed by the 0x3d0000 limitation of the TFTP
flashing process. Addressing this by shrinking the firmware
partition is not a good solution to that problem, though:

1. For a working image, the size of the content has to be smaller
   than the available space, so empty erase blocks will remain.

2. Conceptually, the restriction is on the image, so it makes sense
   to implement it in the same way, and not via the partitioning.
   Users could e.g. do initial flash with TFTP restriction with
   an older image, and then sysupgrade into a newer one, so TFTP
   restriction does not apply.

3. The (content) size of the recovery image is enforced to 0x3d0000
   by the tplink-v2-image command in combination with
   TPLINK_FLASHLAYOUT (flash layout in mktplinkfw2.c) anyway.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:59:44 +02:00
Adrian Schmutzler
0a5d74fa68 arc770: use generic 02_sysinfo
Currently arc770 sets a board name from compatible for no apparent
reason. Just use the compatible directly instead.

This theoretically removes a board name "generic" when no compatible
was present, however, there is no case where this "generic" board
name was actually used.

This also fixes an issue where snps,axs101 would not have been
properly detected anyway, as its case was not set up syntactically
correct.

Fixes: 576621f1e3 ("linux: add support of Synopsys ARC770-based boards")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:28:09 +02:00
Adrian Schmutzler
3c190ef112 archs38: use generic 02_sysinfo
Currently archs38 sets a board name from compatible for no apparent
reason. Just use the compatible directly instead.

This theoretically removes a board name "generic" when no compatible
was present, however, there is no case where this "generic" board
name was actually used.

This also fixes an issue where snps,axs103 would not have been
properly detected anyway, as its case was not set up syntactically
correct.

Fixes: 73015c4cb3 ("linux: add support of Synopsys ARCHS38-based boards")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 18:28:09 +02:00
David Bauer
9662b9d688 ramips: switch MT7620 subtarget to 5.4
MT7620 seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.

Tested on Archer C2 v1 / Archer C20i

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-22 17:20:38 +02:00
David Bauer
4cd5ce5a7f ramips: increase SPI frequency for MT7620 Archer
Increase the SPI frequency for the MT7620 based TP-Link Archer
series to 30MHz.

TP-Link uses different SPI flash chips for the same board
revision, so be conservative to not break boards with a
different chip. 30MHz should be well supported by all chips.

Tested on Archer C2 v1 (GD25Q64B) and Archer C20i (W25Q64FV).

Archer C20i (before)
====================
root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k
122+0 records in
122+0 records out
real	0m 15.30s
user	0m 0.00s
sys	0m 15.29s

Archer C20i (after)
===================
root@OpenWrt:~# time dd if=/dev/mtd1 of=/tmp/test.bin bs=64k
122+0 records in
122+0 records out
real	0m 5.99s
user	0m 0.00s
sys	0m 5.98s

Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-22 17:20:24 +02:00
David Bauer
9a9cdc65c4 ath79: re-enable image generation for GL-AR750S
The bootloader only writes the first 2MB of the image to the NOR flash
when installing the NAND factory image. The bootloader is capable of
booting larger kernels as it boots from the memory mapped SPI flash.

Disable the NAND factory image. The NAND can be bootstrapped by writing
the NAND initramfs image using the NOR upgrade method in the bootloader
web-recovery and sysupgrading from there. The NOR variant is not
affected.

Also refactor the partition definitions in the DTS to make them less
annoying to read.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-22 17:18:55 +02:00
Adrian Schmutzler
5e86877f36 ath79: correctly define WiFi switch for TL-WR841ND v8
The TL-WR841ND v8 feature a WiFi switch instead of a button.
This adds the corresponding input-type to prevent booting into
failsafe regularly.

This has been defined correctly in ar71xx, but was overlooked
when migrating to ath79. In contrast, the TL-WR842ND v2, which
has the key set up as switch in ar71xx, actually has a button.
The TL-MR3420 v2 has a button as well and is set up correctly
for both targets. (Information based on TP-Link user guide)

Note:

While looking into this, I found that support PR for TL-MR3420 v2
switched reset button to ACTIVE_HIGH. However, the other two
device still use ACTIVE_LOW. This seems strange, but I cannot
verify it lacking the affected devices.

Fixes: FS#2733
Fixes: 9601d94138 ("add support for TP-Link TL-WR841N/ND v8")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 12:02:35 +02:00
Adrian Schmutzler
42dc5c2a3f ramips: improve LED support for D-Link DIR-615 D series
This patch adds a trigger for the WAN LED and enhances support for
the WiFi LED by enabling activity indication.

This is based on bug report feedback (see reference below).

While at it, update the LED node names in DTS file.

Fixes: FS#732

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:59:17 +02:00
Adrian Schmutzler
05c74e4000 omap: derive DEVICE_DTS from device name
In most cases the DEVICE_DTS name can be derived easily from the
node name, so let's do this to enforce harmonized names where
possible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:57:22 +02:00
Adrian Schmutzler
eff0a0e39e apm821xx: derive DEVICE_DTS from device name
The DEVICE_DTS variable always matches the device definition name,
just with "_" replaced by "-". Thus, create a DEVICE_DTS definition
in Device/Default and drop all the individual statements.

If necessary in the future, local DEVICE_DTS will still overwrite
that default.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:56:35 +02:00
Adrian Schmutzler
a2fee73e27 bcm47xx: fix switch setup for Linksys WRT610N v2
WRT610N V2 is not detected by the initial network configuration script.
The switch remains unconfigured and wlan/lan vlans are not created.

This adds the correct setup for the device.

Fixes: FS#1869

Suggested-by: Alessandro Radicati
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:55:31 +02:00
Adrian Schmutzler
683193cfb7 layerscape: fix indent
Fix indent to be consistent with the rest of the file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-21 11:51:51 +02:00
Nelson Cai
6269f10ea4 ramips: fix network setup for Ubiquiti ER-X/ER-X-SFP
The function name ucidef_set_interface_lan_wan does not exist,
use the proper name by adding an "s" and thereby fix network
setup on these devices.

Fixes: 22468cc40c (ramips: erx and erx-sfp: fix missing WAN interface)

Signed-off-by: Nelson Cai <niphor@gmail.com>
[commit message/title facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-20 17:16:47 +02:00
Dustin Gathmann
d5a148f5c8 lantiq/xrx200: make WLAN button responsive on Fritzbox 7360 & 7362
Pressing the 'WLAN' button should enable/disable wireless activity.
Currently, the button is mapped to the KEY_WLAN, which will not
have this effect.
This patch changes the mapping of the WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects.

This fix is analogous to the preceding patch for Fritzbox 3370.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
2020-07-20 00:58:30 +02:00
Dustin Gathmann
0ee30adb46 lantiq/xrx200: fix WLAN button actions for Fritzbox 3370
The WLAN button actions are reversed, i.e. pressing the button emits a
'released' action, and vice versa.
This can easily be checked by adding
logger -t button_action "$BUTTON $ACTION"
as the second line of /etc/rc.button/rfkill, and using logread to read
the events (assuming the preceding patch has been applied).
Defining the GPIO as ACTIVE_LOW corrects this behavior.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
2020-07-20 00:58:30 +02:00
Dustin Gathmann
a53bf63756 lantiq/xrx200: make WLAN button responsive on Fritzbox 3370
Pressing the 'WLAN' button should enable/disable wireless activity.
However, on the Fritzbox 3370 this doesn't have an effect.
This patch changes the mapping of the physical WLAN button, so a button
press will emit an action for the 'rfkill' key instead of 'wlan'.
Apparently, this is what stock OpenWRT expects, and also what is
implemented for most other devices.

Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
2020-07-20 00:58:30 +02:00
Alexander Müller
1623defbdb ramips: fix flash layout for TP-Link TL-WR841N v14
The config partition was missing from the flash layout of the device.

Although the stock firmware resets a corrupted config partition to the
default values, the TFTP flash with an image bigger than 0x3d0000 will
truncate the image as the bootloader only copies 0x3d0000 bytes to flash
during TFTP flashing.

Fixed by adding the config partition and shrinking the firmware
partition.

Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
2020-07-19 02:01:06 +02:00
Adrian Schmutzler
2e4626ae77 ramips: remove incorrect mtd-eeprom for TP-Link TL-WR841N v14
The factory partition on this device is only 64k in size, so having
mediatek,mtd-eeprom = <&factory 0x10000> would place the EEPROM data
after the end of the flash. As can be verified against the TP-Link
GPL sources, which contain the EEPROM data as binary blob, the actual
address for the EEPROM data is 0x0.

Since 0x0 is default for MT7628, the incorrect line is just removed.

This error is the reason for the abysmal Wifi performance that people
are complaining about for the WR841Nv14.

Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-19 02:01:06 +02:00
David Bauer
612d5282b5 ramips: don't create switch config for VIXMINI
Don't create UCI switch config for the GL.iNet microuter-N300 and
VIXMINI. These devices only have a single LAN port.
Creating the switch config makes usage of VLANs more complicated,
as they would have to be configured on the MAC as well as the "switch".

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-18 22:12:19 +02:00
Adrian Schmutzler
b78a266888 lantiq: move 01_led_migration script to subtargets
Split the /etc/uci-defaults/01_led_migration scripts into subtargets
as already done for most of the other base-files.

While this introduces a minor amount of code duplication, it still
is considered an improvement, as device-specific settings are kept
together in the subtargets' base-files and the script at hand can be
removed entirely for two of the subtargets not needing it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-17 12:14:32 +02:00
Martin Schiller
4d8552c265 lantiq: move dsl related base-files into own package
It does not make sense to install this components on lantiq systems
where the dsl subsystem is not needed/used.

This also makes it possible to use the files also on other targets.
(hopefully ipq401x / FritzBox 7530 in the near future)

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
2020-07-17 12:14:32 +02:00
Adrian Schmutzler
1de9cac2f9 ramips: move redundant console setup to mt7621 SoC DTSI
For mt7621, console is set up via DTS bootargs individually in
device DTS/DTSI files. However, 44 of 74 statements use the
following setting:

	chosen {
		bootargs = "console=ttyS0,57600";
	};

Therefore, don't repeat ourselves and move that definition to the SoC
DTSI file to serve as a default value.

This patch is cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-17 12:14:32 +02:00
John Audia
b6443367d8 kernel: bump 5.4 to 5.4.52
update_kernel.sh refreshed all patches, no human interaction was needed

Build system: x86_64
Run-tested: Netgear R7800 (ipq806x)

Signed-off-by: John Audia <graysky@archlinux.us>
2020-07-17 11:00:33 +02:00
Salvatore Mesoraca
2a43ab4a18 ramips: add arl_table support for MT7530
Use switch.h API to expose MT7530's ARL table to
user space.

Signed-off-by: Salvatore Mesoraca <salvatore@samknows.com>
2020-07-17 11:00:33 +02:00
Alberto Bursi
480003e9eb mvebu: add Kobol Helios 4 device
The Helios 4 is a NAS from Kobol
that is powered by an Armada 38x
MicroSOM from Solidrun, similarly
to Clearfog.

This device has:
-Armada 38x CPU
 (dual core ARMv7 1.6 Ghz)
-2 GB of ECC RAM
-Gigabit ethernet (Marvell)
-2x USB 3.0 ports
-4x Sata 3.0 ports
-i2c header (J9 |>GND|SDA|SCL|VCC)
-2x 3-pin fan headers with PWM
-micro-usb port is a TTL/UART to
 USB converter connected to TTL
-MicroSD card slot
-System, 4xSata and 1xUSB LEDs

NOT WORKING: fan control

Fan Control requires a kernel patch
that is available in the Armbian
project (the "default firmware"
of this device) and named
mvebu-gpio-remove-hardcoded
-timer-assignment
This patch isn't acceptable
by OpenWrt, it should be upstreamed.
I also have that patch in my own
local OpenWrt builds,
in case you want a more
clean and less confusing patch
for upstreaming.

To install, write the disk image
on a micro SD card with dd or
win32 disk imager, insert the
card in the slot.
Check that the dip switch battery
for boot selection is as follows
Switch 1 and 2 down/off, switches
3, 4, 5 up/on.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-07-17 11:00:33 +02:00
Mateus B. Cassiano
73e8f23579 ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
        WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882

Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
          2 - RXD
          3 - TXD
          4 - GND

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 18:40:20 +02:00
Santiago Rodriguez-Papa
ed087cba8a ramips: add support for Linksys EA7300 v1
Specifications:

* SoC:      MediaTek MT7621A              (880 MHz 2c/4t)
* RAM:      Nanya NT5CC128M16IP-DIT       (256M DDR3-1600)
* Flash:    Macronix MX30LF1G18AC-TI      (128M NAND)
* Eth:      MediaTek MT7621A              (10/100/1000 Mbps x5)
* Radio:    MT7615N                       (2.4 GHz & 5 GHz)
            4 antennae: 1 internal and 3 non-deatachable
* USB:      3.0 (x1)
* LEDs:
    White   (x1 logo)
    Green   (x6 eth + wps)
    Orange  (x5, hardware-bound)
* Buttons:
    Reset   (x1)
    WPS     (x1)

Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 13:39:44 +02:00
Adrian Schmutzler
95a05b12d7 ramips: provide common definition for ELECOM WRC GS devices
Add a common definition for ELECOM WRC "GS" devices to mt7621.mk
to not repeat the same assignments five times.

To keep the naming consistent, slightly rename the DTSI and the
factory image recipe as well.

Note that elecom_wrc-1167ghbk2-s uses a slightly different build
recipe for the factory image, so we keep it separate.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
2020-07-16 13:39:44 +02:00
INAGAKI Hiroshi
a79f55e7e0 ramips: add support for ELECOM WRC-1750GS/GSV
ELECOM WRC-1750GS is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

WRC-1750GSV has the same hardware with WRC-1750GS.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from ethernet port side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-1750GS (or WRC-1750GSV) normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
   for WRC-1750GS : wrc-1750gs-squashfs-factory.bin
   for WRC-1750GSV: wrc-1750gsv-squashfs-factory.bin
4. Wait ~120 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-07-16 13:39:44 +02:00
John Crispin
eff87b8f93 mediatek: backport latest pci/e driver from upstream
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-16 09:18:28 +02:00
John Crispin
5a5031e70b mediatek: generate UBI images for the rev board
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-16 09:16:34 +02:00
John Crispin
ea2884e018 mediatek: minor fix to eip97 driver
This patch makes the driver work on the newer v2.3 core.

Signed-off-by: John Crispin <john@phrozen.org>
2020-07-16 09:14:49 +02:00
Adrian Schmutzler
9f3415d30b ath79: harmonize model names for Ubiquiti devices
This harmonizes the model names for the ath79 Ubiquiti devices by
applying a few minor cosmetic adjustments:

- Removes hyphens where they are not found in the product names
  (Ubiquiti uses hyphens only for the abbreviated version names
  like UAP-AC-PRO which we don't use anyway.)

- Add (XM) suffix for DTS model strings to help with distinguishing
  them from their XW counterparts.

- Remove DEVICE_VARIANT for LAP-120 which actually was an alternate
  device name.

- Generally make DTS model names and those from generic-ubnt.mk
  more consistent.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-15 18:41:57 +02:00
Vieno Hakkerinen
8c7e9cc6b5 ath79: add support for Ubiquiti PowerBridge M
This adds support for the Ubiquiti PowerBridge M, which has the same
board/LEDs as the Bullet M XM, but different case and antennas.

Specifications:
- AR7241 SoC @ 400 MHz
- 64 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- Internal antenna: 25 dBi
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB

Flashing via WebUI:
Upload the factory image via the stock firmware web UI.

Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!

Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.

Flashing via TFTP:
Same procedure as other Bullet M (XM) boards.

- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
  tftp> bin
  tftp> trace
  tftp> put openwrt-ath79-generic-xxxxx-ubnt_powerbridge-m-squashfs-factory.bin

Signed-off-by: Vieno Hakkerinen <vieno@hakkerinen.eu>
2020-07-15 18:33:56 +02:00
John Crispin
9da2b56760 ipq40xx: fix ethernet vlan double tagging
As the the SoC uses implicit vlan tagging for dual MAC support, the
offload feature breaks when using double tagging.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-14 18:31:48 +02:00
John Crispin
2557d2eb4c ipq40xx: merge all ar40xx patches into one single patch
Signed-off-by: John Crispin <john@phrozen.org>
2020-07-14 18:31:12 +02:00
Adrian Schmutzler
3635f7efc1 ipq806x: really fix aliases node for Qualcomm IPQ8064/DB149
Having looked at this again, it appears that only gsbi2_serial
is actually enabled for this device, so the entry in the broken
aliases node was correct.

Therefore, this needs to set its own serial0 instead of inheriting
"serial0 = &gsbi4_serial;" from DTSI. Do this with the correctly
named aliases node now.

Fixes: c83f7b6d21 ("ipq806x: fix aliases node name for Qualcomm
IPQ8064/DB149")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 17:02:40 +02:00
Adrian Schmutzler
e363470d1a ipq806x: use consistent DT labels for gsbiX_serial
Kernel uses the label gsbiX_serial, so let's adjust our labels to
this naming scheme.

This is cosmetic, and actually only already existing gsbi4_serial
has been used at all.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 12:38:24 +02:00
Adrian Schmutzler
c83f7b6d21 ipq806x: fix aliases node name for Qualcomm IPQ8064/DB149
This device uses a node incorrectly named "alias" instead of
"aliases" since it was introduced.

Remove it without replacement, as the definitions in it don't
seem to be required anyway:

The serial0 definition has never been effective anyway and this
would be the only device deviating from the common setting
"serial0 = &gsbi4_serial;" for ipq8064. (So, maybe the wrong
node prevented us from finding out about the wrong serial
definition?)

The mdio-gpio0 alias was supposed to be removed in d2a2eb7e48
anyway, the redundant definition in the alias node was just
overlooked back then.

Fixes: 0fd202f3e5 ("ipq806x: add db149 dts files")
Fixes: d2a2eb7e48 ("ipq806x: replace caf nss-gmac driver by upstream stmmac")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-14 12:38:24 +02:00
Roger Pueyo Centelles
26fda610f3 ath79: use rgmii-id instead of rgmii in ubnt,lap-120
Since commit 6f2e1b7485 (ath79: disable delays on AT803X config init)
the incoming incoming traffic on the ubnt,lap-120 devices Ethernet
port was not making it through. Using rgmii-id instead of rgmii (same
configuration as ubnt,litebeam-ac-gen2) fixes it.

Fixes FS#2893.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2020-07-13 23:35:51 +02:00
Mathieu Martin-Borret
d7233b0a6a ramips: add support for D-Link DIR-878 A1
Specifications:

    SoC: MT7621AT
    RAM: 128MB
    Flash: 16MB NOR SPI flash
    WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
    LAN: 5x1000M
    Firmware layout is Uboot with extra 96 bytes in header
    Base PCB is AP-MTKH7-0002
    LEDs Power Green,Power Orange,Internet Green,Internet Orange
    LEDs "2.4G" Green & "5G" Green connected directly to wifi module
    Buttons Reset,WPS,WIFI

Flashing instructions:

Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.

Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1

Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-13 22:45:04 +02:00
Mathieu Martin-Borret
96761ecc2f kernel: mtdsplit_uimage: add SGE parser
Adding SGE parser for SGE (T&W) Shenzhen Gongjin Electronics
to add 96 bytes padding the the firmware image

Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
2020-07-13 22:45:04 +02:00
David Bauer
0485fb3925 rockchip: don't disable timer LED trigger
The timer LED trigger is enabled in all targets (except for lantiq
xway-legacy). It's necessary for the OpenWrt preinit LED pattern to
work.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-13 17:50:53 +02:00
David Bauer
875a04478c rockchip: use downstream GPIO button implementation
Use the OpenWrt netlink GPIO button implementation to forward button
presses to procd. This is necessary to make failsafe-mode access
using a button possible.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-13 17:50:35 +02:00
Adrian Schmutzler
eb15b0e0c9 bcm47xx: disable image for Linksys WRT160n v3
The device can only hold 3.6 MB, but newer images (since 18.06)
are bigger, so flashing a new version fails.

This disables default build for this device based on the bug report
referenced below.

Fixes: FS#1963

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-13 10:37:22 +02:00
Adrian Schmutzler
11478524a2 ramips: consolidate Netgear devices for mt7628
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.

As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.

Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-13 10:37:22 +02:00
Chuanhong Guo
28893f5878 ath79: fix dsa binding for TP-Link TL-WR941ND v2
upstream changed dt-bindings for marvell 88e6060 to use mdio-device
and dropped support for legacy bindings.
fix it in our local dts.

Fixes: FS#2524
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-12 16:17:28 +08:00
Chuanhong Guo
0997342f24 ath79: qihoo,c301: use phy-supply for usb vbus
Linux phy subsystem provides support for a phy regulator defined via
phy-supply property. Use it to turn on usb power only when usb is
probed.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-12 15:39:18 +08:00
Tomasz Maciej Nowak
2dc5ce622a mvebu: add support for MACCHIATObin Single Shot
Add support for Marvell MACCHIATObin Single Shot, cortex-a72 based
Marvell ARMADA 8040 Community board. Single Shot was broken as the
device tree is different on the Double Shot Board.

Specifications:
- Quad core Cortex-A72 (up to 2GHz)
- DDR4 DIMM slot with optional ECC and single/dual chip select support
- Dual 10GbE (1/2.5/10GbE) SFP+
  2.5GbE (1/2.5GbE) via SFP
  1GbE via copper
- SPI Flash
- 3 X SATA 3.0 connectors
- MicroSD connector
- eMMC
- PCI x4 3.0 slot
- USB 2.0 Headers (Internal)
- USB 3.0 connector
- Console port (UART) over microUSB connector
- 20-pin Connector for CPU JTAG debugger
- 2 X UART Headers
- 12V input via DC Jack
- ATX type power connector
- Form Factor: Mini-ITX (170 mm x 170 mm)

More details at http://macchiatobin.net

Installation:

Write the Image to your Micro SD Card and insert it in the
MACCHIATObin Single Shot SD Card Slot.

In the U-Boot Environment:
   1. reset U-Boot environment:
      env default -a
      saveenv

   2. prepare U-Boot with boot script:
      setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000"
      saveenv

   or manually (hanging lines indicate wrapped one-line command):
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr
         $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr - $fdt_addr'
      saveenv

   On newer Bootloaders (18.12) the Variables have been changed, use:
      setenv fdt_name armada-8040-mcbin-singleshot.dtb
      setenv image_name Image
      setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr_r
         $image_name;ext4load mmc 1:1 $fdt_addr_r $fdt_name;setenv
         bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti
         $kernel_addr_r - $fdt_addr_r'

Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: Alexandra Alth <alexandra@alth.de>
[add specs and installation as provided by Alexandra Alth]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-12 02:06:02 +02:00
Adrian Schmutzler
479adb0929 ramips: consolidate recipes with uimage_padhdr
There are already two very similar recipes using uimage_padhdr
in ramips target, and a third one is about to be added.

Make the recipe more generic, so redefinitions are not necessary
anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
2020-07-11 18:38:42 +02:00
Adrian Schmutzler
9faf9f8f23 mvebu: fix support for Marvell 8040 MACCHIATOBin
Between kernels 4.20 and 5.0, a new variant of this board has been
introduced ("Single Shot"), and the existing one has been renamed
with the appendix "Double Shot". [1]
This also adjusted the first compatible in the list:

marvell,armada8040-mcbin -> marvell,armada8040-mcbin-doubleshot

This patch updates the OpenWrt implementation of this device by
adjusting the relevant references to that compatible (i.e., our
board name).

To still provide support for 4.19 with our setup, this adds a
small patch to change the compatible there as well.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=b1f0bbe2700051886b954192b6c1751233fe0f52

Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-07-11 18:38:42 +02:00
Daniel González Cabanelas
cef9e5a49f bcm63xx: R5010UNv2: fix flash partitions for 16MB flash
The router Nucom R5010UN v2 has the partitions defined for a 8MB flash,
but the flash chip is 16MB size. We are wasting half of the flash.

Fix it and use generic names for partitions.

Fixes: 474cde6123 ("brcm63xx: probe SPI flash through DT")

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-07-11 15:47:46 +02:00
Roman Yeryomin
2ca084ccaa build: improve ccache support
Set CCACHE_DIR to $(TOPDIR)/.ccache and CCACHE_BASEDIR to $(TOPDIR).
This allows to do clean and dirclean. Cache hit rate for test build
after dirclean is ~65%.
If CCACHE is enabled stats are printed out at the end of building process.
CCACHE_DIR config variable allows to override default, which could be useful
when sharing cache with many builds.
cacheclean make target allows to clean the cache.

Changes from v1:
- remove ccache directory using CCACHE_DIR variable
- remove ccache leftovers from sdk and toolchain make files
- introduce CONFIG_CCACHE_DIR variable
- introduce cacheclean make target

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2020-07-11 15:19:53 +02:00
DENG Qingfang
23de93a521 ramips: mt7621: refactor set affinity script
The current one only looks for mt76x2e and mt7603e, and
does not work for 2 or more same Wi-Fi chips.
Refactor the script to cover those cases.

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-07-11 15:15:04 +02:00
Yangbo Lu
2a5460b11b layerscape: define IMAGE_SIZE and LS_SYSUPGRADE_IMAGE_SIZE
Define 64m IMAGE_SIZE for flash firmware.bin since the flash size
is 64MB. Define 48m LS_SYSUPGRADE_IMAGE_SIZE for flash sysupgrade.bin
which contains maximum 16MB kernel and 32MB rootfs according to
memory map.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:23 +02:00
Yangbo Lu
0841b68c91 layerscape: support sysupgrade for SD card ext4 rootfs
Support sysupgrade for SD card ext4 rootfs.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:23 +02:00
Yangbo Lu
c4d0e57e16 layerscape: support sysupgrade for squashfs rootfs
Support sysupgrade for all Layerscape boards with squashfs
rootfs.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:22 +02:00
Yangbo Lu
3a99b624d8 layerscape: fix board name for SD card boot
Many Layerscape boards support both flash boot and SD card boot.
And different firmware and sysupgrade.bin are built for the two
boot methods. To identify them, a fix could be done on board name
by adding a postfix "-sdboot" for SD card boot.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:22 +02:00
Yangbo Lu
3a3b9ded50 layerscape: add compatible for board ls1043ardb
Backport a dts patch which added compatible for ls1043ardb.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:22 +02:00
Yangbo Lu
5ca8903631 layerscape: convert to squashfs rootfs for QSPI NOR boot
There had been an issue in Layerscape QSPI driver for very long
time, which made squashfs,jffs2 rootfs not work on QSPI NOR.
And the ubifs had been used as a workaround.
Now the issue has been fixed. So convert to use squashfs,jffs2
rootfs on QSPI NOR for Layerscape boards (LS1012ARDB/LS1046ARDB/
LS1088ARDB), and update u-boot bootargs for booting.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-07-11 14:44:22 +02:00
Petr Štetiar
df09cc6ddb toolchain/wrapper.sh: fix remaining shellcheck warnings
Fixes following warnings:

 In target/toolchain/files/wrapper.sh line 18:
 REALNAME=$(readlink -f $0)
                        ^-- SC2086: Double quote to prevent globbing and word splitting.
 --
 In target/toolchain/files/wrapper.sh line 20:
 REALNAME_BASE=$(basename $REALNAME)
                          ^-------^ SC2086: Double quote to prevent globbing and word splitting.
 --
 In target/toolchain/files/wrapper.sh line 21:
 REALNAME_DIR=$(dirname $REALNAME)
                        ^-------^ SC2086: Double quote to prevent globbing and word splitting.
 --
 In target/toolchain/files/wrapper.sh line 74:
 		exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $GCC_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_CFLAGS $TARGET_ROOTFS_CFLAGS "$@"
                     ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
 --
 In target/toolchain/files/wrapper.sh line 77:
 		exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $LD_SYSROOT_FLAGS $TARGET_FUNDAMENTAL_LDFLAGS "$@"
                      ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
 --
 In target/toolchain/files/wrapper.sh line 80:
 		exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin $TARGET_FUNDAMENTAL_ASFLAGS "$@"
                      ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.
 --
 In target/toolchain/files/wrapper.sh line 83:
 		exec $TARGET_TOOLCHAIN_TRIPLET-$BINARY.bin "$@"
                      ^-----------------------^ SC2086: Double quote to prevent globbing and word splitting.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 13:33:28 +02:00
Rosen Penev
d8e6a92e7c toolchain/wrapper.sh: Replace read with read -r
Without -r, backslashes would get mangled.

Found with shellcheck.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2020-07-11 13:33:28 +02:00
Alexey Dobrovolsky
ecda6b791b ramips: kernel: fix awake-rt305x-dwc2 patch
At this point in v5.4 kernel we cannot use dwc2_readl() and
dwc2_writel() since they rely on the value hsotg->needs_byte_swap
which cannot be obtained before the controller wakes up.
We should use readl() and writel() to wake up the controller before
calling dwc2_check_core_endianness().

Fixes: 6be0da90a1 ("ramips: refresh patches")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed Fixes: tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 13:33:28 +02:00
Pawel Dembicki
67ce9aedd6 kirkwood: add support for Check Point L-50
This patch adds support for the Check Point L-50 from 600/1100 series
routers.

Specification:
-CPU: Marvell Kirkwood 88F6281 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL

Known issues:
-DSL not supported
-Expresscard not tested

Installation:

Step one -> backup:
make backup u-boot and env for revert stock posibility
make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr

Step two -> Use kwboot tool to upload openwrt u-boot to RAM:

run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t"
end start u-boot

Step three -> Restore macs (e.g. below):
setenv eth1addr 00:1C:XX:XX:XX:6C
setenv ethaddr 00:1C:XX:XX:XX:6B
setenv lan1_mac_addr 00:1C:XX:XX:XX:6C
setenv lan2_mac_addr 00:1C:XX:XX:XX:6D
setenv lan3_mac_addr 00:1C:XX:XX:XX:6E
setenv lan4_mac_addr 00:1C:XX:XX:XX:6F
setenv lan5_mac_addr 00:1C:XX:XX:XX:70
setenv lan6_mac_addr 00:1C:XX:XX:XX:71
setenv lan7_mac_addr 00:1C:XX:XX:XX:72
setenv lan8_mac_addr 00:1C:XX:XX:XX:73
setenv dmz_mac_addr 00:1C:XX:XX:XX:74
setenv dsl_mac_addr 00:1C:XX:XX:XX:75

Step four -> flash u-boot:
mw 0x0800000 0xffff 0x100000
nand erase 0x0 100000
tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb
nand write 0x0800000 0x0 0x100000
saveenv

Step five -> run initramfs image:

tftpboot 0x02000000 openwrt.bin; bootm 0x02000000;

Step six -> install sysupgrade OpenWrt image:

copy to /tmp/ sysupgrade image
run sysupgrade

Back to stock:
Restore original u-boot end env.
Install factory image via stock u-boot.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00
John Audia
039fd27173 kernel: bump 5.4 to 5.4.51
update via update_kernel.sh -v -u 5.4

Removed upstreamed patches:
 350-MIPS-Add-missing-EHB-in-mtc0-mfc0-sequence-for-DSPen.patch

Script refreshed patches:
 902-debloat_proc.patch
 904-debloat_dma_buf.patch

Attempted merge conflict in following patches:
 0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch

Build system: x86_64
Build tested: ipq806x (Netgear R7800)

Signed-off-by: John Audia <graysky@archlinux.us>
[fixed sha256sum of the tarball]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-11 13:33:28 +02:00
Pawel Dembicki
f93267bccf ipq806x: enable Linksys EA8500 eth1 interface
At this moment Linksys EA8500 uses only eth0.

This patch change switch registers, which allow to use eth1 as lan
and eth0 as wan. The method work with similar Linksys EA7500V1
and it work with EA8500.

Suggested-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Brian Onn <brian.a.onn@gmail.com>
Tested-by: Adrian Panella <ianchi74@outlook.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-11 13:33:28 +02:00
Adrian Schmutzler
bc85cc2b42 ath79: disable TP-Link TL-WR941ND v2
The support for this device's Marvell MV88E6060 switch has been
reported to be broken with kernels 4.19/5.4 (see bug report).

Since this a 4/32 device and it has been confirmed to be working
with stable 19.07 release (kernel 4.14), and since fixing it does
not seem trivial, let's just disable it in master.

Fixes: FS#2524

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-11 11:47:47 +02:00
Tim Thorpe
edbc8e5512 ramips: add support for Netgear R6020
This adds support for the Netgear R6020, aka Netgear AC750.

The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

MAC addresses based on vendor firmware:
LAN      *:88   0x4
WAN      *:89
WLAN2    *:88   0x4
WLAN5    *:8a   0x8004

The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-10 11:39:05 +02:00
Willem van den Akker
0df71e01cf lantiq: set correct gphy pins for Zyxel P-2812
This fixes the gphy LED pins for Zyxel P-2812 devices. The have
been accidentally altered during a tidy-up operation (see Fixes:
below).

No ports were available, dmesg reported:

[ 0.658577] pinctrl-xway 1e100b10.pinmux: pin io5 already requested by
            1e100bb0.stp; cannot claim for 1e108000.eth
[ 0.667566] pinctrl-xway 1e100b10.pinmux: pin-5 (1e108000.eth) status -22
[ 0.685238] lantiq,xrx200-net 1e108000.eth: Error applying setting,
            reverse things back
[ 0.693270] lantiq,xrx200-net: probe of 1e108000.eth failed with error -22

Fixes: FS#3188
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the
Ethernet controller node")

Suggested-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Willem van den Akker <wvdakker@wilsoft.nl>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-10 10:06:34 +02:00
David Woodhouse
f632747704 mediatek: fix bashism in gen_banana_pi_img.sh
There was a bashism in the script. This fixes the script so that it
doesn't actually require bash, and can be run with any POSIX shell as
its shebang suggests.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-09 11:11:31 +02:00
Sungbo Eo
36105880ee mediatek: re-add u3phy2 phy-switch patch
This patch is required for pcie@2,0 in mt7623 to work. The patch was originally
added in kernel 4.14, but it has not been ported to 4.19 and later.

Fixes: FS#3217
Tested-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-09 10:28:40 +02:00
Sungbo Eo
923792369e mediatek: do not create device nodes in uci-defaults script
Since commit 298814e6be ("base-files: config_generate: split macaddr with
multiple ifaces") uci MAC address setup will create a device node for each
member iface. But this script might override the device nodes and interfere
with the MAC address setup.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-09 10:28:40 +02:00
Petr Štetiar
c7b750e7ac treewide: kernel: drop redundant USB_EHCI_HCD=n config symbol
Commit e53ec043ba ("kirkwood: move usb support to modules") has moved
this config symbol into generic configs, so it could be removed from
other configs.

Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-09 10:28:40 +02:00
Sebastian Schaper
361c670a46 ath79: add support for D-Link DAP-1330/DAP-1365 A1
Port device support for DAP-1330 from the ar71xx target to ath79.

Additionally, images are generated for the European through-socket
case variant DAP-1365. Both devices run the same vendor firmware, the
only difference being the DAP_SIGNATURE field in the factory header.
The vendor's Web UI will display a model string stored in the flash.

Specifications:

 * QCA9533, 8 MiB Flash, 64 MiB RAM
 * One Ethernet Port (10/100)
 * Wall-plug style case (DAP-1365 with additional socket)
 * LED bargraph RSSI indicator

Installation:

 * Web UI: http://192.168.0.50 (or different address obtained via DHCP)
   There is no password set by default
 * Recovery Web UI: Keep reset button pressed during power-on
   until LED starts flashing red, upgrade via http://192.168.0.50
 * Some modern browsers may have problems flashing via the Web UI,
   if this occurs consider booting to recovery mode and flashing via:
   curl -F \
     files=@openwrt-ath79-generic-dlink_dap-1330-a1-squashfs-factory.bin \
     http://192.168.0.50/cgi/index

The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-07-09 10:28:40 +02:00
Sungbo Eo
358aec7775 ath79: add support for Arduino Yun
Arduino Yun is a microcontroller development board, based on Atmel
ATmega32u4 and Atheros AR9331.

Specifications:
- MCU: ATmega32U4
- SoC: AR9331
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
- Ethernet: 1x 10/100Mbps
- USB: 1x 2.0
- MicroSD: 1x SDHC

Notes:
- Stock firmware is based on OpenWrt AA.
- The SoC UART can be accessed only through the MCU.
  YunSerialTerminal is recommended for access to serial console.
- Stock firmware uses non-standard 250000 baudrate by default.
- The MCU can be reprogrammed from the SoC with avrdude linuxgpio.

Installation:
1.  Update U-Boot environment variables to adapt to new partition scheme.
    > setenv bootcmd "run addboard; run addtty; run addparts; run addrootfs; bootm 0x9f050000 || bootm 0x9fea0000"
    > setenv mtdparts "spi0.0:256k(u-boot)ro,64k(u-boot-env),15936k(firmware),64k(nvram),64k(art)ro"
    > saveenv
2.  Boot into stock firmware normally and perform sysupgrade with
    sysupgrade image.
    # sysupgrade -n -F /tmp/sysupgrade.bin

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-08 23:22:30 +02:00
David Woodhouse
af9932c9b7 mediatek: Implement sysupgrade support for Banana Pi R2
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
e19ffb25d9 mediatek: store MAC address in boot partition on Banana Pi R2
Like many boards, the Banana Pi R2 doesn't have permanant storage of
its MAC address, and we store the first random one that the kernel
generates in order to use it later and at least be consistent.

Store it in the FAT boot partition, just as the U7623 board (and others)
do.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
7adc29f59e mediatek: add SD card image creation for Banana Pi R2
Based on work by Alexey Loukianov <lx2@lexa2.ru> and others.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
91e43a1d7a mediatek: enable SATA for mt7623
The MT7623 SoC has the same SATA block as the MT7622, so enable it in
MT7623 builds too and add it to the DEVICE_PACKAGES for those boards.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
c848bc6cd5 mediatek/mt7623: unify features and packages, add ext4 and usb
The supported MT7623 boards are mostly identical (what with being a
System-on-Chip and all), so unify the DEVICE_PACKAGES for them, and add
ext4 and usb support for them.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
David Woodhouse
c07d0d7f3e mediatek: mt7623: refresh 5.4 kernel config
Some options were not explicitly specified, causing the kernel build to
drop to interactive mode. Set the missing options.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-08 23:22:30 +02:00
Sebastian Schaper
14599c5945 ath79: add support for D-Link DCH-G020 Rev. A1
The DCH-G020 is a Smart Home Gateway for Z-Wave devices.

Specifications:

 * QCA9531, 16 MiB Flash, 64 MiB RAM
 * On-Board USB SD3503A Z-Wave dongle
 * GL850 USB 2.0 Hub (one rear port, internal Z-Wave)
 * Two Ethernet Ports (10/100)

Installation:

 * Web UI: http://192.168.0.60 (or different address obtained via DHCP)
   Login with 'admin' and the 6-digit PIN Code from the bottom label
 * Recovery Web UI: Keep reset button pressed during power-on
   until LED starts flashing red, upgrade via http://192.168.0.60
 * Some modern browsers may have problems flashing via the Web UI,
   if this occurs consider booting to recovery mode and flashing via:
   curl -F \
     files=@openwrt-ath79-generic-dlink_dch-g020-a1-squashfs-factory.bin \
     http://192.168.0.60/cgi/index

Known issues:

 * Real-Time-Clock is not working as there is currently no matching driver
   It is still included in the dts as compatible = "pericom,pt7c43390";
 * openzwave was tested on v19.07 (running MinOZW as a proof-of-concept),
   but the package grew too big as lots of device pictures were included,
   thus any use of Z-Wave is up to the user (e.g. extroot and domoticz)

The device will use the same MAC address for both wired and wireless
interfaces, however it is stored at two different locations in the flash.

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2020-07-08 22:54:34 +02:00
John Audia
3e992ea790 ipq806x: compile in schedutil governor
Gives users a third option to augment ondemand and performance. Kernel
docs[1] explain differences and this PR empowers users w/ the choice to
select between the older ondemand and newer and more simplistic schedutil
should they wish to use one that is not the performance governor.

1. Documentation/admin-guide/pm/cpufreq.rst

Signed-off-by: John Audia <graysky@archlinux.us>
[fixed From: to match SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 22:54:13 +02:00
Furkan Alaca
541faf2c93 ramips: mt7621: use lzma-loader for ra21s & rg21s
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).

Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
2020-07-08 22:52:40 +02:00
Sergei Burakov
4dc9ad4af8 ramips: add support for ZyXEL Keenetic Lite Rev.B
Device specification:

SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button

Flash instruction:

Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
2020-07-08 22:52:40 +02:00
Adrian Schmutzler
9e6257c26c ramips: move adslr_g7 in image/mt7621.mk to keep sorting
Move this device to the top to maintain alphabetic sorting in the
file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Adrian Schmutzler
7de08be913 ramips: add missing kmod-mt7615-firmware for TP-Link RE500 v1
Adding this has been overlooked when rebasing the commit prior to
merge.

Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Adrian Schmutzler
f3921acdf0 ipq40xx: fix patches on dts Makefile
The patches for arch/arm/boot/dts/Makefile have not been updated
in a syntactically correct way (just body was changed). Fix it.

Fixes: 4a77a060ab ("ipq40xx: add support for Buffalo WTR-M2133HP")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 17:50:12 +02:00
Bjørn Mork
c1794d653c ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC:   MediaTek MT7621ST
WiFi:  MediaTek MT7603
       Quantenna QT3840BC
Flash: 128M NAND
RAM:   64M
LED:   Dual colour red and green
BTN:   Reset
       WPS
Eth:   4 x 10/100/1000 connected to MT7621 internal switch
       MT7621 RGMII port connected to Quantenna module
GPIO:  Power/reset of Quantenna module

Quantenna module
----------------

The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation.  It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621.  It loads both a second uboot stage and an os
image from the MT7621 using tftp.  The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.

There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.

Serial ports
------------

Two serial ports with headers:

RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1   -  57600 8N1 - Connected to the MT7621 console

Both share pinout with many other Zyxel/Mitrastar devices:

1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND

Dual system partitions
----------------------

The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.

OpenWrt does not support this scheme and will always use the
first OS partition.  It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.

Installation from vendor firmware
---------------------------------

1. Run a DHCP server. The WAP6805 is configured as a client device
   and does not have a default static IP address. Make a note of
   which address it is assigned

2. tftp the OpenWrt initramfs-kernel.bin image to this address.
   Wait for the WAP6805 to reboot.

3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
   backup of all mtd partitions now.  The last used OEM image is
   still present in either "Kernel" or "Kernel2" at this point,
   and can be restored later if you save a copy.

4. sysupgrade to the OpenWrt sysupgrade.bin image.

Installation from U-Boot
------------------------

This requires serial console access

1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
   your tftp server directory.  Configure the server address as
   192.168.0.33/24

2. Hit ESC when the message "Hit ESC key to stop autoboot"
   appears

3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.

4. Answer Y to the question "Erase Linux in Flash then burn new
   one. Are you sure?", and answer the address/filename questions.
   Defaults:
        Input device IP (192.168.0.2)
        Input server IP (192.168.0.33)
        Input Linux Kernel filename ("ras.bin")

5. Wait until after you see the message "Done!" and power cycle
   the device.  It will hang after flashing.

6. Continue with step 3 and 4 from the vendor firmware procedure.

Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme.  These changes appear to have
broken a few things.  The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work.  The image selection
scheme is unreliable and inconsistent.  A limited U-Boot menu is
available - and used by the above U-Boot install procedure.  But
direct booting into an uploaded image does not work, neither with
ram nor with flash.  Flashing works, but requires a hard reset after
it is finished.

Reverting to OEM firmware
-------------------------

The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.

  ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin

OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required.  See above.

Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware.  But the branding features do obviously
differ.

LED controller
--------------

Hardware implementation is unknown.  The dual-color LED is controlled
by 3 GPIOs:

  4: red
  7: blinking green
 13: green

Enabling both red and green makes the LED appear yellow.

The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
20c7abd4b7 ipq806x: add support for Linksys EA7500 V1
This patch adds support for the Linksys EA7500 V1 router.

Specification:
 - CPU: Qualcomm IPQ8064
 - RAM: 256MB
 - Flash: NAND 128MB
 - WiFi: QCA9982 an+ac + QCA9983 bgn
 - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337)
 - USB: 1x USB 3.0 1x USB2.0
 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level)
 - 2 Buttons
 - 1 LED

Known issues:
 - Some devices won't flash via web gui

Installation:
- Newer stock images doesn't allow to install custom firmware.
- Please downgrade software to 1.1.2 version. Official firmware:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img
- Do it two times to downgrade all stored images.
- Apply factory image via web-gui.

Serial + TFTP method:
 - downgrade to 1.1.2 two times
 - connect ehternet and serial cable
 - set ip address of tftp server to 192.168.1.254
 - put openwrt factory image to tftp folder and rename it to macan.bin
 - stop device while booting in u-boot
 - run command: "run flashimg"
 - run command: "setenv boot_part 1"
 - run command "saveenv"
 - reset

Back to stock:
- Please use old non-gpg image like this 1.1.2:
https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img
- ssh to router and copy image to tmp
- use sysupgrade -n -F

Tested by github users: @jack338c and @grzesiczek1

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 16:07:05 +02:00
Yanase Yuki
4a77a060ab ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
d2c3131b3f kirkwood: add support for Zyxel NSA310S
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6702 1 GHz
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 2x USB 2.0
 - 1x SATA
 - 3x button
 - 7x leds
 - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)

Known issues:
 - no kernel module for RTC. [*]
 - buzzer (connected to MPP43) need to be drived by 1kHz signal
 - no kernel module for internal MCU connected via I2C[**]

[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

Installation:

TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftp 0x0800000 nsa310s-u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
4. Copy and run initramfs image
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftpboot zyxel_nsa310s-initramfs-uImage
	=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade

USB:

1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
   Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> usb start
	=> fatload usb 0 0x0800000 u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
5. Copy and run initramfs image:
	=> usb start
	=> fatload usb 0 0x0800000 initramfs-uImage
	=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.

Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Andrey Bondar
ba59021d64 ath79: add support for 8devices Lima board
Specification:

  • 650/600/216 MHz (CPU/DDR/AHB)
  • 64 MB of RAM (DDR2)
  • 32 MB of FLASH
  • 2T2R 2.4 GHz
  • 2x 10/100 Mbps Ethernet
  • 1x USB 2.0 Host socket
  • 1x miniPCIe slot
  • UART for serial console
  • 14x GPIO

Flash instructions:

Upgrading from ar71xx target:

  • Upload image into the board:
    scp openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin
    root@192.168.1.1/tmp/
  • Run sysupgrade
    sysupgrade -F /tmp/openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin

Upgrading from u-boot:

  • Set up tftp server with
    openwrt-ath79-generic-8dev_lima-initramfs-kernel.bin
  • Go to u-boot (reboot and press ESC when prompted)
  • Set TFTP server IP
    setenv serverip 192.168.1.254
  • Set device ip from the same subnet
    setenv ipaddr 192.168.1.1
  • Copy new firmware to board
    tftpboot 0x82000000 initramfs.bin
  • Boot OpenWRT
    bootm 0x82000000
  • Upload image openwrt-ath79-generic-8dev_lima-squashfs-sysupgrade.bin into
    the board
  • Run sysupgrade.

Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
2020-07-08 16:07:05 +02:00
Sergio E. Nemirowski
645b1ec3e2 build: add 'make kernel_xconfig' command
This adds the kernel_xconfig make target.

Signed-off-by: Sergio E. Nemirowski <sergio@outerface.net>
2020-07-08 16:07:05 +02:00
Dongming Han
f103321349 ipq40xx: add support for GL.iNet GL-S1300
Specifications:
SOC:        Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM:        512 MiB
FLASH1:     16 MiB NOR - SPI0
FLASH2:     8 GiB eMMC
ETH:        Qualcomm QCA8075
WLAN1:      Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2:      Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT:      Reset, WPS
LED:        Power, Mesh, WLAN
UART1:      On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2:      On board with BLE module
SPI1:       On board socket for Zigbee module

Install via tftp
- NB: need to flash transition image firstly

Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf

Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script

The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.

Signed-off-by: Dongming Han <handongming@gl-inet.com>
2020-07-08 16:07:05 +02:00
Emir Efe Kucuk
53a1fede1f ramips: Add support for Xiaomi Mi Router(Black,R2100)
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"

See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg

Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot

Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo

Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client

1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0

other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)

MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004

Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
78fffc2dfd generic: platform/mikrotik: add partial AR71xx cpufreq support
This patch adds cpu frequency setting for AR724x and AR7161.
It is unknown if all the AR71xx devices support the same value range,
so support is only enabled for AR7161 at this stage.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
a874c87f4c generic: platform/mikrotik: add board_revision tag
Tag was discovered exploring the hard_config of a "r2" board.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
0217a9be0d generic: platform/mikrotik: graceful fallback for cpufreq_index
The current code would return an error on ath79 when the SoC isn't known
to the driver. Return the raw hex value instead, as happens with non
supported targets.
Also return the correctly incremented value from
sc_tag_cpufreq_ath79_arraysize()

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
2714a4faab generic: platform/mikrotik: match RouterBOOT nomenclature
RouterBOOT cpu frequency settings are letter-indexed. Follow the
same logic for the sysfs interface.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-07-08 16:07:05 +02:00
Thibaut VARÈNE
5c4b431a3c generic: platform/mikrotik: fix routerboot_tag_show_u32s()
The routine would only accurately print out the first word.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fixes: 5ecf7d96 ("generic: routerboot sysfs platform driver")
2020-07-08 16:07:05 +02:00
Davide Fioravanti
8c13ebd3ad ramips: add support for Edimax Gemini RE23S
Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH:   1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615 (4x4:4)
  - 5GHz:   1x MT7615 (4x4:4)
  - 4 antennas: 2 external detachable and 2 internal
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x Green led (Power)
  - 1x Green-Amber-Red led (Wifi)
UART:
  - 57600-8-N-1

Everything works correctly.

Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)

Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Restoring procedure tested with RE23_1.08.bin

MAC addresses
-------------
factory 0x4     *:24
factory 0x8004  *:25
Cimage  0x07    *:24
Cimage  0x0D    *:24
Cimage  0x13    *:24
Cimage  0x19    *:25

No other addresses were found in factory partition.

Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.

Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.

If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 13:28:17 +02:00
Hauke Mehrtens
66e04abbb6 ar71xx: Fix mikrotik NAND compile problem
This Fixes the folowing compile error:
drivers/mtd/nand/rb91x_nand.c: In function 'rb91x_nand_remove':
drivers/mtd/nand/rb91x_nand.c:445:16: error: 'rbni' undeclared (first use in this function)
  nand_release(&rbni->chip);

Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-07 23:38:10 +02:00
Petr Štetiar
ae2d249056 ath79: nand: disable images for glinet_gl-ar750s
Fixes following build failures:

 WARNING: Image file glinet_gl-ar750s-nor-kernel.bin is too big
 WARNING: Image file glinet_gl-ar750s-nor-nand-kernel.bin is too big

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-07 19:47:24 +02:00
Andrey Bondar
326e488c7b ath79: add support for 8devices Rambutan board
Rambutan is a Wifi module based on QCA9550/9557
http://www.8devices.com/products/rambutan

Specification:

- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of DDR2 RAM
- 128 MB of NAND Flash
- 1x 100Mbps Ethernet
- 1x 1000Mbps Ethernet (PHY on dev-kit)
- 1x Wifi radio 2x2 MIMO, dualband 2.4 and 5 GHz
- 2x U.FL connectors on module, chip antennas on dev-kit
- 1x miniPCIe slot
- 2x USB2.0 host
- 2x UART
- SPI, I2C, GPIO

Flash instructions:

Upgrade from ar71xx target:
 sysupgrade -F /tmp/openwrt-ath79-nand-8dev_rambutan-squashfs-sysupgrade.tar
or upgrade from GUI (don't save config)

Use factory image to flash from U-Boot:
 tftpboot 80060000 openwrt-ath79-nand-8dev_rambutan-squashfs-factory.ubi
 nand erase.part ubi
 nand write 80060000 ubi ${filesize}

Signed-off-by: Petr Štetiar <ynezz@true.cz> [copy&pasted missing commit description]
Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
2020-07-07 19:47:24 +02:00
Adrian Schmutzler
7cb721c03f ramips: use WiFi LED DT triggers for TP-Link RE650 v1
This moves WiFi LED triggers from 01_leds to device tree.

While at it, convert the labels there to lower case; this is
more commonly used and the change will actually remove competition
between DT trigger and leftover uci config on already installed
systems.

Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 11:57:48 +02:00
David Bauer
d8ab3216e6 ath79: switch to kernel 5.4
As the reported major bugs are ironed out, switch to the new kernel to
begin testing with a broader audience.

Signed-off-by: David Bauer <mail@david-bauer.net>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-07 10:33:17 +02:00
Aleksander Jan Bajkowski
f496939f15 lantiq: set port numbers corresponding to reg value
Fix inconsistencies found in DTS files and sort ethernet ports based on
updated names.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[squash two separate patches, rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 01:03:59 +02:00
Aleksander Jan Bajkowski
3866fefa38 lantiq: remove redundant includes from fritz736x DTS files
The removed lines are already included in vr9_avm_fritz736x.dtsi

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:59:51 +02:00
Christoph Krapp
ba0f4f0cfd ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:40:04 +02:00
Martin Blumenstingl
982468de35 lantiq: dts: Move the &usb_vbus nodes out of &gpio
Move the USB VBUS regulator nodes out of the GPIO controller node. This
fixes a problem where the "regulator-fixed" driver wasn't probed for
these regulators because the GPIO driver doesn't scan the child-nodes
and based on the dt-bindings documentation it's not supposed to.

This fixed the following error reported by Luca Olivetti:
  ...
  dwc2 1e101000.usb: DWC OTG Controller
  dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
  dwc2 1e101000.usb: irq 62, io mem 0x1e101000
  dwc2 1e101000.usb: startup error -517
  dwc2 1e101000.usb: USB bus 1 deregistered
  dwc2 1e101000.usb: dwc2_hcd_init() FAILED, returning -517

Fixes: FS#1634
Cc: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-07-06 20:23:33 +02:00
Matthew Gyurgyik
bb14d44039 kernel/pcengines-apu2: detect apuv4 board
Upstream commit 3d00da1de3 ("platform/x86: pcengines-apuv2: detect apuv4
board")

On 5.4, this module fails on APUv4 due to non-matching DMI data. With this
patch, the module will match DMI data for the APUv4.

Signed-off-by: Matthew Gyurgyik <matthew@gyurgyik.io>
[include upstream patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:33 +02:00
Lars Wessels
f855eb91b3 lantiq: added switch-config for ARV752DPW
Add missing switch config (4 LAN-Ports + CPU).

Grey WAN port (used for ADSL) is not part of the switch.

Signed-off-by: Lars Wessels <software@bytebox.org>
[rework commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:24 +02:00
Lars Wessels
702366a30b lantiq: wifi mac fix for ARV752DPW
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).

Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).

Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:13 +02:00
Sunguk Lee
2d378703f1 ramips: reduce spi-max-frequency for ipTIME A8004T
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.

A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)

In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.

Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:25:32 +02:00
Adrian Schmutzler
883250014d ipq806x: move serial0 to DTSI files
All device DTS files in the target set the serial0 property to the
same value (*). So, let's move the definitions to the DTSI files.

That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).

* The only exception is ipq8064-db149, which defines
  "serial0 = &uart2;", but inside a block called "alias" instead of
  "aliases". It must be assumed that this is broken anyway, so we
  don't touch it here.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:24:30 +02:00
Adrian Schmutzler
74e339f118 ipq806x: move stdout-path to DTSI files
All device DTS files in the target set the stdout-path to the same
value. So, let's move the definitions to the DTSI files.

That's also where the kernel defines it (qcom-ipq8064-v1.0.dtsi).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:23:23 +02:00
Adrian Schmutzler
ed761344d2 ipq806x: disentangle and clean up SoC DTSI files
So far, the DTSI files on ipq806x had a linear inheritance:

  qcom-ipq8064.dtsi
  v
  qcom-ipq8064-v1.0.dtsi
  v
  qcom-ipq8064-v2.0.dtsi
  v
  qcom-ipq8065.dtsi

This poses problems when one wants to set something that is specific
to an architecture closer to the top of the tree.

In this patch, we remove the chain-like inheritance and have all
other files derived from qcom-ipq8064.dtsi (changing this name to
something more generic is not possible due to upstream use).

The removal of inheritance will require a few entries to be copied
from qcom-ipq8064-v2.0.dtsi to qcom-ipq8065.dtsi. However, it also
opens an opportunity for some clean-up:

- Many definitions can be improved by just using the innermost labels.

- Instead of disabling the CPU_SPC node for ipq8065, it is now off by
  default and enabled where needed.

- Instead of patching phy-tx0-term-offset into qcom-ipq8064.dtsi and
  then having it changed for qcom-ipq8064-v2.0/qcom-ipq8065, just have
  the appropriate settings done in the lower DTSI files directly.

- For the opp_table0 adjustments for ipq8065, just redefine what's
  changed, but don't add all the untouched properties again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-06 16:21:15 +02:00
Sungbo Eo
19c8f11d92 ipq806x: move common pinmux nodes to SoC DTSI
As almost same pinmux nodes are repeated in each device dts,
let's define them once in the ipq8064 dtsi and remove the rest.

* uart0_pins : Did not touch.
* i2c4_pins  : This node seems to be not used at all in dts.
               Added the most common form in the dtsi. Did not touch rpm_pins.
* spi_pins   : The common mux node is already present in the dtsi.
               Removed the duplicate nodes from dts.
* nand_pins  : Moved the entire node.
* mdio0_pins : Moved the common mux node.
* rgmii2_pins: Moved the common mux node. "pins" property is overrided in ap161.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-06 16:08:18 +02:00
Hauke Mehrtens
014d3f593a ar71xx: Fix mikrotik NAND compile problem
There is one closing bracket too much.

Fixes: ce958dd88a ("kernel: Update kernel 4.14 to version 4.14.187")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-06 00:07:38 +02:00
Scott Roberts
d31bbe40e2 mvebu: config define i2c pxa slave
We are setting CONFIG_I2C_PXA is not set
If you do set pxa to y then you have issues if you do not have
CONFIG_I2C_PXA_SLAVE is not set

Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
2020-07-04 21:12:42 +02:00
Daniel González Cabanelas
a902e6a657 mvebu: LS421DE: use automatic fan control with thermal zones
The Buffalo Linkstation LS421DE has a chassis fan for cooling two internal
hard drives. Currently there is no control over this fan, running always
at fixed medium speed.

With the recent jump to the kernel 5.4, now we can monitor the hard drive
temperature and control the fan with thermal zones.

Install the kmod-hwmon-drivetemp module and wire up a thermal zone on the
dts file to allow automatic fan control by the kernel.

Tested succesfully using a single Crucial BX500 SSD drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
68d9cb8214 kernel: Update kernel 5.4 to version 5.4.50
Run tested: ath79, ipq40xx
Build tested: ath79, ipq40xx

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
6062d85892 kernel: Update kernel 4.19 to version 4.19.131
Fixes:
- CVE-2020-10757

The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.

Run tested: ath79
Build tested: ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
ce958dd88a kernel: Update kernel 4.14 to version 4.14.187
Fixes:
- CVE-2020-10757

The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.

Build tested: ramips

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Hauke Mehrtens
4bb5e331a7 kernel: Fix ath79 DSP exception at bootup
This resolves a hazard between a mtc0 and a mfc0 instruction after
activating the DSP support. Without this fix the CPU could use the old
value again and the DSP support would not be active.

Fixes: FS#2928, FS#2899
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: David Bauer <mail@david-bauer.net> [ocedo_koala/ocedo_raccoon]
2020-07-04 16:04:21 +02:00
Antti Seppälä
a175bc8f36 ath79: add support for GL.iNet GL-MiFi
Add support for the ar71xx supported GL.iNet GL-MiFi to ath79.

Specifications:
 - Atheros AR9331
 - 64 MB of RAM
 - 16 MB of FLASH (SPI NOR)
 - 2x 10/100/1000 Mbps Ethernet
 - 2.4GHz (AR9330), 802.11b/g/n
 - 1x USB 2.0 (vbus driven by GPIO)
 - 4x LED, driven by GPIO
 - 1x button (reset)
 - 1x mini pci-e slot (vcc driven by GPIO)

Flash instructions:

Vendor software is based on openwrt so you can flash the sysupgrade
image via the vendor GUI or using command line sysupgrade utility.
Make sure to not save configuration over reflash as uci settings
differ between versions.

Note on MAC addresses:

Even though the platform is capable to providing separate MAC addresses
to the interfaces vendor firmware does not seem to take advantage of
that. It appears that there is only single unique pre-programmed
address in the art partition and vendor firmware uses that for
every interface (eth0/eth1/wlan0). Similar behaviour has also been
implemented in this patch.

Note on GPIOs:

In vendor firmware the gpio controlling mini pci-e slot is named
3gcontrol while it actually controls power supply to the entire mini
pci-e slot. Therefore a more descriptive name (minipcie) was chosen.
Also during development of this patch it became apparent that the
polarity of the signal is actually active low rather than active high
that can be found in vendor firmware.

Acknowledgements:

This patch is based on earlier work[1] done by Kyson Lok. Since the
initial mailing-list submission the patch has been modified to comply
with current openwrt naming schemes and dts conventions.

[1] http://lists.openwrt.org/pipermail/openwrt-devel/2018-September/019576.html

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
2020-07-03 20:48:05 +02:00
John Audia
472f5b1474 ipq806x: refresh config
Based on "make kernel_menuconfig CONFIG_TARGET=generic" and 5.4.49

CONFIG_LEDS_TRIGGER_DISK has been removed by the refresh and added
back manually in order to not revert f93fcf8923 ("ipq806x: enable
disk-activity LED trigger").

Signed-off-by: John Audia <graysky@archlinux.us>
[extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 20:38:06 +02:00
Sungbo Eo
91472dc2ce kirkwood: support for button in Pogoplug V4
Pogoplug V4 has a reset button on a GPIO pin.
To use it, kmod-gpio-button-hotplug package needs to be installed.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-03 19:48:51 +02:00
Adrian Schmutzler
b123ffdf6e ath79: drop redundant status for gpio target-wide
All definitions of gpio in SoC DTSI files do not set status, i.e.
have it enabled. This drops all remaining redundant "status = okay"
definitions in descendent files (mostly older ones).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Adrian Schmutzler
dc1280ef65 ath79: enable gpio on ar933x by default
All other SoC DTSI files have gpio enabled by default, only
ar9330/ar9331 disable it by default, only to have it enabled again
afterwards for each individual device.

So, do not disable it in the first place, and drop all device-specific
status statements afterwards.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Leon M. George
a0bb356612 ath79: add support for Compex WPJ344
Specifications:

SoC: AR9344
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 Gigabit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 48V IEEE 802.3af/at - 24V passive optional
USB 2.0 header

Installation:

To install, either start tftp in bin/targets/ath79/generic/ and use
the u-boot prompt over UART:

tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj344-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot

The cpximg file can be used with sysupgrade in the stock firmware (add
SSH key in luci for root access) or with the built-in cpximg loader.
The cpximg loader can be started either by holding the reset button
during power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.

For example, if the board is labelled '6A08':

tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj344-16m-squashfs-cpximg-6a08.bin

MAC addresses:

<&uboot 0x2e010>  *:99  (label)
<&uboot 0x2e018>  *:9a
<&uboot 0x2e020>  *:9b
<&uboot 0x2e028>  *:9c

Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.

Signed-off-by: Leon M. George <leon@georgemail.eu>
[minor commit message adjustments, drop gpio in DTS, DTS style fixes,
sorting, drop unused cpximg recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-03 17:37:02 +02:00
Sungbo Eo
736995ce19 ath79: rearrange nand node by register address
All other nodes in the DTS are placed in order of address space. Harmonize
the nand nodes as well.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-07-02 21:34:37 +02:00
Rowan Border
33fae8421e ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.

Specifications

MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.

Web Interface Installation

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Signed-off-by: Rowan Border <rowanjborder@gmail.com>
2020-06-30 17:23:32 +02:00
Kevin Darbyshire-Bryant
d59dc14515 kernel: cake: backport upstream tweaks & fixes
From upstream:
b8392808eb3f sch_cake: add RFC 8622 LE PHB support to CAKE diffserv handling
3f608f0c4136 sch_cake: fix a few style nits
8c95eca0bb8c sch_cake: don't call diffserv parsing code when it is not needed
9208d2863ac6 sch_cake: don't try to reallocate or unshare skb unconditionally

From netdev not yet accepted:
sch_cake: fix IP protocol handling in the presence of VLAN tags

The VLAN tag handling is actually wider than just cake so upstream are
working out how to fix it generically.  We fix it here just for cake.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-06-30 16:09:18 +01:00