152 Commits

Author SHA1 Message Date
Sebastian Schaper
907cb88e10 mediatek: filogic: add support for WAVLINK WL-WN573HX3
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).

Specifications:

- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
    four single band RP-SMA fiberglass antennas (8 dBi)

Installation:

- OEM Web UI is at 192.168.30.1 which will forward to
    http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
    http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings

MAC address assignment:

LAN         80:xx:xx:76:xx:25  hw 0x44e
WLAN 2.4G   80:xx:xx:76:xx:27  factory 0x04 (label MAC)
WLAN 5G	    82:xx:xx:46:xx:27
pair key    8a:xx:xx:76:xx:27  also on label, not used by OpenWrt

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
2025-04-18 14:00:39 +02:00
Schneider Azima
7921e48d43 mediatek: add support for Mercusys MR80X v3
This commit adds support for Mercusys MR80X(EU) v3 router.

Device specification:
 - SoC: Mediatek MT7981b, Cortex-A53, 64-bit
 - RAM: 512MB
 - Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
 - Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
 - Wireless: 2.4GHz (802.11 b/g/n/ax)
 - Wireless: 5GHz (802.11 a/n/ac/ax)
 - LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
   on ethernet ports
 - Buttons: 1 (Reset)
 - Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
   slots contain "seconduboot" (also U-Boot 2022.01-rc4)

Installation (UART):
 - Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
 - Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'.
 - Set the uboot environment for startup.
   setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
   If the bootarg is set to boot from ubi1, also change it to ubi0.
 - Load and run OpenWrt initramfs image.
   setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
 - Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.

Recovery:
 - Press Reset button and power on the router.
 - Navigate to U-Boot recovery web server (http://192.168.1.1/) and
   upload the OEM firmware.

Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"

ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot   Vol ID: 0|
| Volume Name: kernel  Vol ID: 1|
| Volume Name: rootfs  Vol ID: 2|
+-------------------------------+

MAC addresses:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| label   | 94:0C:xx:xx:xx:12 | label     |
| WAN     | 94:0C:xx:xx:xx:13 | label+1   |
| LAN     | 94:0C:xx:xx:xx:12 | label     |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1   |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2   |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".

Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-04-12 23:50:27 +02:00
Yujie Zhu
db3eff1022 mediatek: filogic: add Netcore N60 Pro support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A

Flash instructions:

    Connect to the router using ssh or telnet,
    username: useradmin, password is the web
    login password of the router.
    Use scp to upload bl31-uboot.fip and flash:
    "mtd write xxx-bl31-uboot.fip FIP"
    "mtd erase ubi"
    Connect to the router via the Lan port,
    set a static ip of your PC.
    (ip 192.168.1.254, gateway 192.168.1.1)
    Download initramfs image, reboot router,
    waiting for tftp recovery to complete.
    After openwrt boots up, perform sysupgrade.

Note:

    Back up all mtd partitions before flashing.

Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-04-10 22:19:33 +02:00
Mikhail Zhilkin
d8002cb627 mediatek: add support for netis NX31
Some checks failed
Build Kernel / Build all affected Kernels (push) Waiting to run
Build all core packages / Build all core packages for selected target (push) Waiting to run
Build and Push prebuilt tools container / Build and Push all prebuilt containers (push) Has been cancelled
Build host tools / Build host tools for linux and macos based systems (push) Has been cancelled
This PR adds support for netis NX31 router.

Specification
-------------
- SoC       : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM       : 256 MiB DDR3
- Flash     : SPI-NAND 128 MiB (ESMT)
- WLAN      : MediaTek MT7976CN dual-band WiFi 6
  - 2.4 GHz : b/g/n/ax, MIMO 2x2
  - 5 GHz   : a/n/ac/ax, MIMO 2x2
- Ethernet  : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
              10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB       : No
- Buttons   : Mesh, Reset
- LEDs      : 1x Power (blue), unmanaged
              1x Status (blue), gpio-controlled
              1x WiFi 2.4 GHz (blue), gpio-controlled
              1x WiFi 5 GHz (blue), gpio-controlled
              3x LAN activity (blue), switch-controlled
              1x WAN activity (blue), gpio-controlled
- Power     : 12 VDC, 1 A

Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
   password)
2. Make mtd backup:
   cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
   cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
   cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
   cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
   cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
   cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
   scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
   dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
   mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
   mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
   'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
   the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
   mtd erase ubi
   reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
   the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
   (IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
    sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb

Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
   router using scp protocol
3. Connect to the router using ssh and run:
   apk update && apk add kmod-mtd-rw
   insmod mtd-rw i_want_a_brick=1
   mtd unlock BL2
   mtd unlock FIP
4. Restore backup:
   mtd write /tmp/mtd4_FIP.bin FIP
   mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
   mtd erase ubi
   reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
   ~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
   upload the OEM firmware

Recovery
--------
1. Place OpenWrt
   'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
   the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
   the button.
3. Use OpenWrt initramfs system for recovery

MAC addresses
-------------
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| LAN     | dc:xx:xx:d1:xx:18 | label     |
| WAN     | dc:xx:xx:d1:xx:1a | label+2   |
| WLAN 2g | de:xx:xx:11:xx:19 |           |
| WLAN 5g | de:xx:xx:71:xx:19 |           |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-04-06 20:14:18 +02:00
Fil Dunsky
99ea96c297 mediatek: filogic: add support for Huasifei WH3000
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ

**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1

**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.

**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.

**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```

**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```

**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)

Number  Start (sector)    End (sector)  Size       Code  Name
   1            8192            9215   512.0 KiB   8300  u-boot-env
   2            9216           13311   2.0 MiB     8300  factory
   3           13312           21503   4.0 MiB     8300  fip
   4           21504           29695   4.0 MiB     8300  config
   5           29696           62463   16.0 MiB    8300  kernel
   6           62464         4256767   2.0 GiB     8300  rootfs
   7         4257792        14940159   5.1 GiB     8300
```

You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit

You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.

Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-04-06 19:22:09 +02:00
Daniel Golle
8b27e60c58 mediatek: filogic: add build for ASUS ZenWiFi BT8 with OpenWrt's U-Boot
Some checks are pending
Build Kernel / Build all affected Kernels (push) Waiting to run
Build all core packages / Build all core packages for selected target (push) Waiting to run
Add 'ubootmod' variant for the ASUS ZenWiFi BT8.
An out-of-tree installer will be provided in Github to allow users an easy
transition from the stock loader to OpenWrt's bootchain which is built from
source.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2025-03-30 02:02:58 +01:00
John Crispin
2cd79733cc mediatek: filogic: add Asus ZenWiFi BT8
Hardware
--------
MediaTek MT7988D SoC (3x Cortex-A73 @1.8 GHz max)
1GB DDR4 RAM
128MB SPI-NAND (Winbond)
MediaTek MT7996 BE14000 Tri-Band Wi-Fi 7
3x LAN (2x 1GE MT7988 built-in, 1x 2.5GE MaxLinear GPY211C)
1x WAN (2.5GE MT7988 built-in)
LED: RGB PWM (supported as 3x PWM LED)
USB: 1x USB 3
Buttons: RESET, WPS
UART: 115200 8N1 3.3V

Installation
------------
1. Hold down RESET button and power on the device until
   LED pulses red.

2. Assign IP 192.168.1.70/24 to your computer's Ethernet port

3. Connect Ethernet to one of the 1GE LAN ports

4. Open browser and visit http://192.168.1.1

5. Upload openwrt-mediatek-filogic-asus_zenwifi-bt8-factory.bin

6. Once OpenWrt initramfs system comes up, do sysupgrade using
   openwrt-mediatek-filogic-asus_zenwifi-bt8-squashfs-sysupgrade.bin

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2025-03-30 02:02:58 +01:00
Christoph Krapp
66f38834d6 mediatek: filogic: fix device sorting
arcadyan_mozart was incorrectly placed below asus devices

Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18331
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-03-26 09:57:23 +01:00
Martin Schiller
1bb9592fc7 mediatek: filogic: bpi-r3-mini: add kmod-eeprom-at24
The bpi-r3-mini has an eeprom onboard. Add the related driver to be
able to access this memory.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2025-03-25 07:48:53 +01:00
Chukun Pan
ddc4f216c6 filogic: move append-gl-metadata to image-commands.mk
This can be used by GL.iNet devices from other target.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-03-24 10:15:59 +01:00
Daniel Golle
6c8cc86295 mediatek: filogic: openwrt-one: drop kmod-nvme
Some checks failed
Build Kernel / Build all affected Kernels (push) Waiting to run
Build all core packages / Build all core packages for selected target (push) Waiting to run
Coverity scan build / Coverity x86/64 build (push) Has been cancelled
The OpenWrt One is the only board listing kmod-nvme as part of it's
default package set.

Remove kmod-nvme from the default package set as the board is sold
without an NVMe SSD and the M.2 slot can also be used for other
purposes.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2025-03-14 11:23:57 +00:00
Martin Schiller
843e50f4fa mediatek: bpi-r4: create additional emmc gpt artifact
This makes it possible to initialize the eMMC from scratch like it is
done for the BPI-R3 mini (without an SD card).

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2025-03-12 12:04:08 +01:00
Tianling Shen
96c6608346 mediatek: add support for CMCC A10
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.

Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, WPS
  Power: DC 12V 1A

Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.

OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
   especially 'Factory' partition.
3. Unlock MTD partitions:
   apk update && apk add kmod-mtd-rw
   insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
   mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
   mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-03-08 15:44:56 +01:00
Pietro Ameruoso
74f0c95154 mediatek: filogic: fix sysupgrade for ex5601-t0-stock
Some checks are pending
Build Kernel / Build all affected Kernels (push) Waiting to run
fix undesired red warning when upgrading in place ex5601-t0-stock model.

Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Link: https://github.com/openwrt/openwrt/pull/17973
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-02-16 22:48:12 +01:00
Aleksander Jan Bajkowski
3d63a41ffa mediatek: EX5601-T0 add Zyxel EX5601-T1 and T-56 alias
Define EX5601-T1 and T-56 as alternative name, to explicitly show
the device is supported using existing image. EX5601-T1 does not
have the option to switch between WAN/SFP port. The switch port
is hardwired to the WAN port. The Zyxel T-56 is the odido-branded
version of the EX5601-T1.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17615
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-01-19 17:51:06 +01:00
Hauke Mehrtens
0f8a5a5fd6 mediatek: filogic: Cudy WR3000H: Fix SUPPORTED_DEVICES
Some checks are pending
Build Kernel / Build all affected Kernels (push) Waiting to run
Build all core packages / Build all core packages for selected target (push) Waiting to run
Fix the name used for the transition image from Cudy.
This should make it possible to use the cudy transition image.

Fixes: 9d66b8b312fb ("mediatek: filogic: Add support for cudy wr3000h")
Link: https://github.com/openwrt/openwrt/pull/17652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-01-18 19:13:44 +01:00
Juan Pedro Paredes Caballero
9d66b8b312 mediatek: filogic: Add support for cudy wr3000h
The manufacturer Cudy usually releases signed openwrt firmware, to
facilitate the migration from the proprietary version to the official
versions of openwrt. In contact with the manufacturer tells me that only
releases the firmware of the WR3000H if and only if
there is an official version. With this proposal I pretend to have an
initial operative version so that they do their part, and facilitate to
the users the possibility of using openwrt. In the present state, it is
only possible to use this firmware by uploading and installing it with
UART connection.

AX3000 2.5G Dual Band Wi-Fi 6 Mesh Router (WR3000H)

Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY (C22)
2 Radios MT7976CN
UART: 115200 8N1 3.3V

MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device + press reset pin. Keep pressing reset pin to
   enter the U-Boot shell (The recovery.bin image load process must fail).

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.88. Rename the image to "cudy3000h.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000h.bin; bootm 0x46000000

5. IMPORTANT: Make backup from original firmware. System -> Backup
   /Flash Firmware -> Save mtdblock contents. All mtdblock one by one,
keep unaltered (BL2, u-boot-env, Factory, bdinfo, FIP, and ubi).

6. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Warning for BL2 and U-BOOT developers
-------------------------------------
The nand partition layout from vendor is slightly diferent from "standard".
The FIP partition starts at 0x3c0000 be carefull with BL2 to BL31.
The UBI partition start at 0x5c0000 be carefull.
DO NOT OVERWRITE bdinfo partition it contains hardware MAC definition
Layout is start-end (not start size)
  - 0x000000000000-0x000007800000 : "nmbm0"
          - 0x000000000000-0x000000100000 : "bl2"
          - 0x000000100000-0x000000180000 : "u-boot-env"
          - 0x000000180000-0x000000380000 : "factory"
          - 0x000000380000-0x0000003c0000 : "bdinfo"
          - 0x0000003c0000-0x0000005c0000 : "fip"
          - 0x0000005c0000-0x0000045c0000 : "ubi"
ALLWAYS for U-BOOT operations check this
setenv mtdids nmbm0=nmbm0
setenv mtdparts nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),256k(bdinfo),2048k(fip),65536k(ubi)

Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17458
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-01-12 17:08:02 +01:00
Roland Reinl
b3ce08e0b6 mediatek: filogic: Add support for D-Link AQUILA PRO AI M60
Specification:
 - MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - MT7531 switch
 - 512MB RAM
 - 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size
 - 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1)
 - 3 buttons (WPS, reset, LED on/off)
 - 1x 2.5 Gbit WAN port with Maxlinear GPY211C
 - 4x 1 Gbit LAN ports

Disassembly:
 - There are five screws at the bottom: 2 under the rubber feet, 3 under the label.
 - After removing the screws, the white plastic part can be shifted out of the blue part.
 - Be careful because the antennas are mounted on the side and the top of the white part.

Serial Interface
 - The serial interface can be connected to the 4 pin holes next to/under the antenna cables.
 - Note that there is another set of 4 pin holes on the side of the board, it's not used.
 - Pins (from front to rear):
   - 3.3V (do not connect)
   - TX
   - RX
   - GND
 - Settings: 115200, 8N1

MAC addresses:
 - MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52)
 - MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53)
 - WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52)
 - LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53)
 - WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54)
 - WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57)

Flashing via OEM web interface:
 - Currently not supported because image crypto is not known

Flashing via recovery web interface:
 - This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition
 - Use a Chromium based browser, otherwise firmware upgrade might not work
 - Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red
 - Upload the recovery image, this will take some time. LED will continue flashing red during the update process
 - The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing
 - If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case:
   - Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image)
   - Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60
   - OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface)
   - Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used

Flashing via Initramfs:
- Before switching to OpenWrt, ensure that both partitions contain OEM firmware.
  - This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface.
  - Flashing via OEM web interface will automatically flash the currently not active partition.
- Open router, connect serial interface
- Start a TFTP server at 192.168.200.2 and provide the initramfs image there
- When starting the router, select "7. Load Image" in U-Boot
- Settings for load address, load method can be kept as they are
- Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2)
- Enter the file name of the initramfs image
- Confirm "Run loaded data now?" question after loading the image with "Y"
- OpenWrt initramfs will start now
- Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM
- Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0
  - During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition

Reverting back to OEM:
- Boot the initramfs image as described in "Flashing via Initramfs" above
- Copy the backed up ubi partition to /tmp (e.g. by using SCP)
- Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4
- Reboot the device, OEM firmware will start now

Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17296
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-23 23:23:18 +01:00
Jianyu Zhuang
e0813dc071 mediatek: filogic: add support for Tenbay WR3000K
Tenbay WR3000K is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B.

- SoC: MetiaTek MT7981B
- RAM: Hynex H5TQ2G863GFR 512MiB
- Flash: Winbond W25N01GVZEIG 128MiB
- Wi-Fi: MediaTek MT7976C (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- MediaTek MT7915E: 2.4GHz and 5GHz
- Ethernet: 1x 10/100/1000 Mbps WAN + 3x 10/100/1000 Mbps LAN
- Switch: MediaTek MT7531AE
- UART: J4 (115200 baud)
- LEDs: Power
- Buttons: Reset, WPS
- PWR: 12V/1A DC, 5.5×2.1 connector

| Vendor  | OpenWrt Interface | Address       | Notes                                          |
|---------|-------------------|---------------|------------------------------------------------|
| WAN     | wan            | Label MAC     |  Stored MAC in factory + offset 4, label MAC is Stored MAC - 2   |
| LAN     | br-lan             | Label MAC+1   |              |
| 2.4GHz  | phy0-ap0          | Label MAC + 2     |             |
| 5GHz    | phy1-ap0          | Label MAC + 3     |              |

- 0x000000000000-0x000000100000 : "BL2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "Factory"
- 0x000000380000-0x000000580000 : "FIP"
- 0x000000580000-0x000003580000 : "ubi"
- 0x000003580000-0x000006580000 : "ubi1"
- 0x000006580000-0x0000065a0000 : "Product"
- 0x0000065a0000-0x000007580000 : "Custom"

- The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi.

- The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt.

- id: 0, kernel
- id: 1, rootfs
- id: 2, rootfs_data

- **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102).
- **Dupont Wires** (male-to-male, 3 wires).
- **PC/Laptop** with a serial communication tool.
- Screwdriver (to open the router case).

1. **OpenWrt Firmware**:
   - Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/).
2. **Serial Communication Tool**:
   - Windows: PuTTY, Tera Term.
   - Linux/Mac: Minicom, screen.
3. (Optional) **TFTP Server**:
   - Install a TFTP server like Tftpd64 or tftp-hpa.

---

1. Open the router casing and locate the **TX, RX, and GND** pins.
2. Connect the router pins to the USB-to-TTL adapter as follows:
   - **TX (router)** → **RX (adapter)**
   - **RX (router)** → **TX (adapter)**
   - **GND (router)** → **GND (adapter)**
3. Do **not** connect the VCC pin to avoid damage.

- **Baud rate**: 115200
- **Data bits**: 8
- **Stop bits**: 1
- **Parity**: None
- **Flow control**: None

---

1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***

    1. Factory mode
    2. Startup system (Default)
    3. Upgrade firmware
    4. Upgrade ATF BL2
    5. Upgrade ATF FIP
    6. Upgrade single image
    7. Load image
    0. U-Boot console

Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Select Option 0 by typing 0 and pressing Enter.
5. Input into
```plaintext
MT7981> setenv boot_from ubi
MT7981> saveenv
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
MT7981> printenv
baudrate=115200
boot_from=ubi
...
```
the above indicates system will start from *ubi*.
and then type
```plaintext
MT7981> reset
```
will boot from *ubi*

1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***

    1. Factory mode
    2. Startup system (Default)
    3. Upgrade firmware
    4. Upgrade ATF BL2
    5. Upgrade ATF FIP
    6. Upgrade single image
    7. Load image
    0. U-Boot console

Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Choose Option 3: Upgrade Firmware
Enter Upgrade Mode
Select Option 3 by typing 3 and pressing Enter.
Upgrade Methods
You will be prompted to choose between:
```plaintext
*** Upgrading Firmware ***

Run image after upgrading? (Y/n): y

Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.10
Input IP netmask: 255.255.255.0
Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin
```
Type Enter to proceed. The router will erase the old firmware and write the new one.

Signed-off-by: Jianyu Zhuang <xzjianyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-22 18:45:01 +01:00
Maxim Anisimov
6992d6e51a mediatek/filogic: add support for Cudy AP3000 v1
Hardware:
  SoC:     MT7981b
  RAM:     512 MB
  Flash:   256 MB SPI NAND
  Ethernet:
    1x2.5Gbps (rtl8221b)
  WiFi:    2x2 MT7981
  Button:  Reset
  LED:     1x multicolor

Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-22 18:38:16 +01:00
Tianling Shen
5a7fb834c7 mediatek: update openembed som7981 support
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).

Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio

Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.

Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-22 18:19:16 +01:00
Jonas Jelonek
cd8dcfef37 mediatek: filogic: bpi-r4: set netdev-name for sfp ports
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
2024-12-20 18:19:10 +01:00
Jonas Jelonek
84fc59c0d5 mediatek: filogic: bpi-r3: set netdev-name for sfp1 port
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
2024-12-20 18:19:10 +01:00
Yaoguang Bai
6b32a5d768 mediatek: filogic: add support for NRadio C8-668GL
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.

- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
  - 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
  - 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
  - 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector

The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:

| Vendor  | OpenWrt Interface | Address       | Notes                                          |
|---------|-------------------|---------------|------------------------------------------------|
| LAN     | br-lan            | Label MAC     | Default                                        |
| WAN     | lan4              | Label MAC+1   | Only when lan4 is switched to WAN             |
| 2.4GHz  | phy0-ap0          | Label MAC     |                                                |
| 5GHz    | phy1-ap0          | Label MAC     | (Local Admin bit set)                         |
| Modem   | eth1              | Label MAC+2   |                                                |

1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
   - Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.

Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```

Power off the router, hold the **WPS button**, and power it back on.

1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.

- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
  ```bash
  cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
  ```

Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
2024-12-13 15:29:04 +01:00
David Bentham
794291bbdf mediatek: add Comfast CF-E395AX support by adding an alternative model name
both these devices share the board and same config, just different model number

Install instructions are the same as the CF-E393AX commit - https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=d8f4453bf2de9fd9baf3d660ed12e0797ff2cfdb

Signed-off-by: David Bentham <db260179@gmail.com>

Link: https://github.com/openwrt/openwrt/pull/16389
Signed-off-by: John Crispin <john@phrozen.org>
2024-12-12 09:46:38 +01:00
Maxim Anisimov
d087a79b7b mediatek/filogic: add Keenetic KN-3811 support
Specification:
 * Mediatek MT7981BA
 * 256 MB SPI-NAND
 * 512 MB DDR4 RAM
 * MT7976CN DBDC AX Wi-Fi
 * MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
 * 4x LED (power, internet, fn, wifi)
 * 3x buttons (wps, fn, reset)
 * 1x USB 3.0 port

Serial Interface:
 * 3 Pins GND, RX, TX
 * Settings: 115200, 8N1

Notes:
 * The device supports dual boot mode
 * Fn led reassigned to wlan 2.4

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
   to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
   the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-08 19:52:35 +01:00
Mikhail Zhilkin
ee8df790ca mediatek: MERCUSYS MR90X v1: add OpenWrt U-Boot (UBI) layout
This commit adds OpenWrt U-Boot (UBI) layout support for MERCUSYS MR90X
v1.

Stock U-Boot UBI size:   50 MiB
OpenWrt U-boot UBI size: 126 MiB

Install
-------
1. Perform steps 1-14 of the OpenWrt installation guide (use OpenWrt
   initramfs-recovery.itb instead of initramfs-kernel.bin at the step 10,
   12 and 14).
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation

2. Make backups:
```
cat /dev/mtd0 > /tmp/boot.bin
cat /dev/mtd5 > /tmp/tp_data.bin
```
   Copy /tp_data dir content, /tmp/boot.bin and /tmp/tp_data.bin and to
   your PC using scp. You can also backup the remaining partititons. Copy
   backups to a safe place, they are required for the next steps and stock
   firmware recovery.

3. Reboot to OpenWrt initramfs:
```
reboot
```

4. Copy OpenWrt ubi-bl31-uboot.fip, ubi-preloader.bin,
   ubi-squashfs-sysupgrade.itb and MT7986_EEPROM.bin, default-mac (from
   /tp_data backup) to the /tmp folder of the router using scp.

5. Prepare UBI:
```
ubidetach -p /dev/mtd3; ubiformat /dev/mtd3 -y; ubiattach -p /dev/mtd3
ubimkvol /dev/ubi0 -N fip -t static -s 1MiB
ubiupdatevol /dev/ubi0_0 /tmp/ubi-bl31-uboot.fip
ubimkvol /dev/ubi0 -N ubootenv -s 0x1f000
ubimkvol /dev/ubi0 -N ubootenv2 -s 0x1f000
```

6.  Install kmod-mtd-rw and unlock partitions:
```
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock boot
mtd unlock bl2
mtd unlock factory
```

7. Prepare "factory" partition:
```
dd if=/dev/zero bs=$((0x8000)) count=1 | tr '\000' '\377' > /tmp/factory.bin
dd if=/tmp/MT7986_EEPROM.bin of=/tmp/factory.bin conv=notrunc
dd if=/tmp/default-mac >> /tmp/factory.bin
```

8. Write "factory" partition:
```
mtd erase factory
mtd write /tmp/factory.bin factory
```

9. Write preloader partition:
```
mtd erase bl2
mtd write /tmp/ubi-preloader.bin bl2
```

10. Write OpenWrt sysupgrade image:
```
sysupgrade -n /tmp/ubi-squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connetion if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Link: https://openwrt.org/toh/mercusys/mr90x_v1#serial

Return to stock:
----------------
1. Copy "boot" partition backup (boot.bin) to the /tmp dir of the router
   using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot:
```
   insmod mtd-rw i_want_a_brick=1
   mtd unlock boot
   mtd erase boot
   mtd write /tmp/boot.bin boot
```

4. Erase UBI and reboot:
```
mtd erase ubi
reboot
```

5. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1

6. Complete steps 1-9 of the OpenWrt installation guide to get root
   rights.
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation

7. Upload "tp_data" partition backup (tp_data.bin) to the /tmp folder of
   the router using scp.

8. Restore stock calibrations:
```
mtd write /tmp/tp_data.bin tp_data
reboot
```

9. Perform "factory restore" via stock firmware web interface.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-30 18:36:05 +01:00
Maxim Anisimov
5a4eb56a7b mediatek/filogic: add Keenetic KN-3911 support
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 512MB RAM
 - 128MB SPI NAND
 - 2 LEDs (green, orange)
 - 3 buttons (fn, reset, wps)
 - 2 2.5Gbit ethernet ports based on Airoha EN8811H phy

Serial Interface:
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

Notes:
 - The device supports dual boot mode

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3911-squashfs-factory.bin"
   to "KN-3911_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
   the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-28 22:33:21 +01:00
George Oldfort
e44180d45c mediatek: filogic: add KTD2026/7 driver to Acer Connect Vero W6m
This commit adds kmod-leds-ktd202x to the OpenWrt image for the device
"Acer Connect Vero W6m" which is equipped with one KTD2026 controlling the
device's status LED via I2C.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-28 21:59:58 +01:00
George Oldfort
1bdb6d8404 mediatek: remove ktd-202x driver filogic image (Aer Vero W6m)
Image build fails with PR #16861 merged while PR #16860 not merged.

Removing kmod-leds-ktd202x from filogic.mk will fix the build process.

Fixes: 2898d1d1269a ("mediatek: add support for Acer Predator W6d and Acer Vero W6m")
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/17087
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-26 10:43:16 +01:00
Mikhail Zhilkin
d413163832 mediatek: Routerich AX3000: add OpenWrt U-Boot layout
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.

Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
   /tmp folder of the router using scp.

2. Make mtd partitions backups:
   http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
   contents

3. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

4. Write FIP and preloader:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/ubootmod-preloader.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```

5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
   with IP 192.168.1.254.

6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.

7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
   router using scp.

8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot

Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
   router using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot and reboot:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/BL2.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/FIP.bin FIP
reboot
```

4. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-24 23:41:02 +01:00
David Ignjic
faf4b3e0f7 mediatek: filogic: add support for Cudy WR3000S v1
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V

MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot  shell.

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.88. Rename the image to "cudy3000s.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000

5. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Signed-off-by: David Ignjic <ignjic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 20:24:57 +01:00
George Oldfort
2898d1d126 mediatek: add support for Acer Predator W6d and Acer Vero W6m
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).

The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.

Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.

This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
George Oldfort
d42075dcef mediatek: improve device tree for Acer Predator Connect W6
In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
  (blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
  (green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface

This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
Romanov Danila
d8a9669093 mediatek: change Routerich AX3000 ubi size
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)

These partitions weren't used:
firmware_backup
zrsave
config2

Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 15:42:24 +01:00
Enrico Mioso
b43194e041 mediatek: filogic: add support for GatoNetworks GDSP
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.

Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
          the built-in Mediatek watchdog is also present and effective, but
          not used at the moment.

This porting has been tested only with 1x 5G modems installed (the device
supports up to two).

Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.

OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:

insmod mtd-rw i_want_a_brick=1

Then update relevant flash partitions:

mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP

And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.

Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).

U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.

MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.

device					MAC address		U-Boot env variable		factory partition offset
2.4 GHz Wi-Fi		:84						wifi_mac							0x4
5.8 GHz Wi-Fi		:85						not present						not present
WAN							:86						wan_mac								0x24
LAN							:87						lan_mac								0x2A

Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2024-11-14 04:14:23 +00:00
John Crispin
a85f11f191 mediatek: filogic: add Arcadyan Mozart platform
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 4 GiB DDR4 RAM
* 2x 10000M + 1x 1000M  ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* 2 buttons (Reset, WPS)
* 2x LED for each GMAC
* USB-C PD power input

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-01 07:43:00 +01:00
Daniel Golle
b27075e12b mediatek: add wireless offloading firmware to MT7988 boards
Install mt7988-wo-firmware by default on boards based on MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-23 13:40:09 +01:00
Daniel Golle
e550c6d381 mediatek: fix OpenWrt One ubinized image in IB
The ImageBuilder when using the profile for the OpenWrt One has been
failing because the initramfs image included in the ubinized image could
not be found.

Fix that by using the staged initramfs instead when using the
ImageBuilder.

Fixes: 797904b3cb ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-21 00:49:22 +01:00
Chukun Pan
e98987048a mediatek: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-10-15 21:36:16 +01:00
Daniel Golle
3f98f68573 mediatek: filogic: select MT7996 2+3+3 firmware
Select MT7996 2+3+3 firmware for the Adtran SmartRG SDG-8733A device
and also add it to the image for the BPi-R4 which supports both,
BE19000 (4+5+5) as well as BE14000 (2+3+3) Wi-Fi 7 modules.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-29 23:04:34 +01:00
Chris Webb
7eda44f536 uboot-mediatek: support GL.iNet GL-X3000 and GL-XE3000
Add u-boot support based on the kernel dts introduced in d1016446 and
the GL-MT6000 u-boot support in fe10f974.

The pcie-mediatek-gen3 kernel driver doesn't like hotplug, so to work in
PCIe mode, the 5G modem on this device needs to be switched on by u-boot
before starting the kernel. Include an init_modem step in the boot_system
action to set the relevant gpios. (The factory bootloader does the same,
using Mediatek SDK-specific gpio_power_clr and gpio_pull_up.)

Ideally the modem would be started using gpio-hog in the device tree, but
this will need to wait until mediatek gpio-hog support is fixed upstream:

  https://lore.kernel.org/u-boot/6ef2583e85eea60560d7776377d662779e7c44e5.1722419839.git.chris@arachsys.com/

The bootloader can be replaced using the built-in web interface of the
factory bootloader. Hold the reset button for five seconds while powering
on the device and it will boot into a recovery http server.

http://192.168.1.1/uboot.html and http://192.168.1.1/bl2.html can then
be used to upload openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip
and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin respectively.

Alternatively, from a root shell on the running system, unlock the boot
partition with

  echo 0 >/sys/block/mmcblk0boot0/force_ro

then write openwrt-mediatek-filogic-glinet_gl-x3000-bl31-uboot.fip to
/dev/mmcblk0p4 and openwrt-mediatek-filogic-glinet_gl-x3000-preloader.bin
to /dev/mmcblk0boot0.

Signed-off-by: Chris Webb <chris@arachsys.com>
Link: https://github.com/openwrt/openwrt/pull/15645
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-09-22 23:50:40 +02:00
Daniel Golle
d0a2b3f824 mediatek: add Adtran SmartRG SDG-8733A
Specification is similar to other devices of the MT Stuart series:
 * Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
 * 8 GiB eMMC
 * 2 GiB DDR4 RAM
 * 2500M/1000M/100M LAN port
 * 10000M/5000M/2500M/1000M/100M/10M WAN port
 * MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
 * Renesas DA14531MOD Bluetooth
 * 2 buttons (Reset, Mesh/WPS)
 * uC-controlled RGB LED via I2C
 * 2x LED for the 2.5G port, 3x LED for the 10G port
 * 3.3V-level 115200 baud UART console via 4-pin Dupont connector
   exposed at the bottom of the device
 * USB-C PD power input

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-20 22:47:05 +01:00
Pawel Dembicki
19d770d7b9 mediatek: filogic: add support for Cudy AP3000 Outdoor
Hardware highlights:
  - MediaTek MT7981 WiSoC
  - 256MB DDR3 RAM
  - 64MB SPI-NAND
  - MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
  - 1x LED in two colors
  - 2x Button
  - 1x 1GbE
  - Two detachable antenas, two internal pcb antenas
  - PoE powered (standalone)

MAC:
LAN MAC: label mac
2.4G MAC: label mac -1
5G MAC: label mac

How to install:
1. Apply Cudy Intermediate OpenWrt image for AP3000 Outdoor V1
2. Install OpenWrt sysupgrade image

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16156
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-25 15:35:53 +02:00
Goetz Goerisch
3774f3272e treewide: rename ZyXEL to Zyxel
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.

This commit aligns the casing of Zyxel everywhere.

Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-25 15:08:25 +02:00
Chukun Pan
73832e1a48 mediatek: add support for TP-Link TL-XTR8488
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: MT40A512M16TB-062ER 1GB
  Ethernet: 2x 2.5G, 4x 1G Lan
  WiFi1: MT7976GN 2.4GHz 4T4R
  WiFi2: MT7976AN 5.2GHz 4T4R
  WiFi3: MT7915AN 5.8GHz 4T4R
  Button: Reset, WPS, Turbo
  USB: 1 x USB 3.0
  Power: DC 12V 5A

Flash instructions:
  1. Execute the following operation to open nc shell:
     https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
  2. Replace the stock bootloader to OpenWrt's:
     dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
     dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
  3. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
  4. Download the initramfs image, and restart the router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-25 22:54:16 +02:00
Rafał Miłecki
74879140a1 treewide: fixup models names for UniFi U6 series
Ubiquiti has a set of UniFi 802.11ax (Wi-Fi 6) AP devices. All models
include "U6" in their names and also have code names with no special
characters (including spaces).

Examples:
1. U6 Lite (codename U6-Lite)
2. U6 Long-Range (codename U6-LR)
3. U6+ (codename U6-PLUS)
4. U6 Pro (codename U6-Pro)
5. U6 Mesh (codename U6-Mesh)
6. U6 Mesh Pro (codename U6-Mesh-Pro)
7. U6 Enterprise (codename U6-Enterprise)

Use proper full names for those devices. Names in OpenWrt/DTS code may
need updating too but it can be handled later.

Cc: Elbert Mai <code@elbertmai.com>
Cc: Daniel Golle <daniel@makrotopia.org>
Cc: Henrik Riomar <henrik.riomar@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-07-25 11:18:25 +02:00
Luca Piccirillo
7390642237 treewide: match the COMFAST brand name across supported devices
COMFAST CF-E393AX
COMFAST CF-E390AX & CF-EW72 V2
COMFAST CF-WR617AC

Signed-off-by: Luca Piccirillo <luca.piccirillo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14690
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 18:08:49 +02:00
Tianling Shen
f2f428c699 mediatek: add ABT ASR3000 support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A

Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
     * Enter fakeroot if you are not login as root.
   base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
   ( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
   tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
   ASR3000 via telnet.

Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
   mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
   mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 16:13:06 +02:00
Dirk Buchwalder
9e49593ff7 mediatek: filogic: add support for TP-LINK RE6000XD
This commit adds support for TP-LINK RE6000XD.
The device is quite similar to the Mercusys MR90X V1,
except only 3 LAN ports and more LEDs.
So thanks to csharper2005 for doing all the groundwork.

Device specification
--------------------
SoC Type:   MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM:        MediaTek MT7986BLA (512MB)
Flash:      SPI NAND GigaDevice (128 MB)
Ethernet:   MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet:   1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1,
            LAN2)
WLAN 2g:    MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g:    MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs:       8 LEDs, 1 status blue, 2x WIFI blue, 2x signal
	    blue/red, 3 LAN blue gpio-controlled
Button:     2 (Reset, WPS)
USB ports:  No
Power:      12 VDC, 2 A
Connector:  Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0
            partition contain "seconduboot" (also U-Boot 2022.01-rc4)

Serial console (UART), unpopulated
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |
    +--- Don't connect

Disassemble: rm the 2 screws at the bottom and the one at the backside.
            un-clip the case starting at the edge above the LEDs.

Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
      tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Notice: while I was successfull at activating ssh (as described
        here:
        https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/)

        Unfortunately I haven't found the correct root password.
        Looks like they are using a static password
        (md5crypt, salt + 21 characters) that is not the web
        interface admin password.

        The TP-LINK RE900XD looks like the very same device,
        according to the pictures and the firmware.
        But I haven't checked if the OpenWrt firmware works as well
        on that device.

        The second ubi partition (ubi1) is empty and there is no known
        dual-partition mechanism, neither in u-boot nor in the stock firmware.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2024-07-04 22:14:32 +02:00