mediatek/filogic: add support for Cudy AP3000 v1

Hardware:
  SoC:     MT7981b
  RAM:     512 MB
  Flash:   256 MB SPI NAND
  Ethernet:
    1x2.5Gbps (rtl8221b)
  WiFi:    2x2 MT7981
  Button:  Reset
  LED:     1x multicolor

Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Maxim Anisimov 2024-12-10 16:37:02 +03:00 committed by Hauke Mehrtens
parent dc655dcfca
commit 6992d6e51a
4 changed files with 239 additions and 6 deletions

View File

@ -0,0 +1,218 @@
// SPDX-License-Identifier: GPL-2.0-only OR MIT
/dts-v1/;
#include "mt7981.dtsi"
/ {
model = "Cudy AP3000 v1";
compatible = "cudy,ap3000-v1", "mediatek,mt7981";
aliases {
label-mac-device = &gmac0;
led-boot = &status_led;
led-failsafe = &status_led;
led-running = &status_led;
led-upgrade = &status_led;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
button-reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
};
};
gpio-leds {
compatible = "gpio-leds";
led-0 {
color = <LED_COLOR_ID_RED>;
function = LED_FUNCTION_WLAN_2GHZ;
gpios = <&pio 4 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
led-1 {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_WLAN_5GHZ;
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy1tpt";
};
status_led: led-2 {
color = <LED_COLOR_ID_AMBER>;
function = LED_FUNCTION_STATUS;
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
};
};
watchdog {
compatible = "linux,wdt-gpio";
gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
hw_algo = "level";
hw_margin_ms = <10000>;
always-running;
};
};
&uart0 {
status = "okay";
};
&watchdog {
status = "okay";
};
&eth {
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins>;
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-handle = <&phy1>;
phy-mode = "2500base-x";
nvmem-cell-names = "mac-address";
nvmem-cells = <&macaddr_bdinfo_de00 0>;
};
};
&mdio_bus {
phy1: phy@1 {
reg = <1>;
interrupt-parent = <&pio>;
interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
reset-gpios = <&pio 39 GPIO_ACTIVE_LOW>;
reset-assert-us = <100000>;
reset-deassert-us = <100000>;
};
};
&pio {
spi0_flash_pins: spi0-pins {
mux {
function = "spi";
groups = "spi0", "spi0_wp_hold";
};
conf-pu {
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
drive-strength = <MTK_DRIVE_8mA>;
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
};
conf-pd {
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
drive-strength = <MTK_DRIVE_8mA>;
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
};
};
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_flash_pins>;
status = "okay";
/* ESMT F50L2G41XA (256M) */
spi_nand@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spi-nand";
reg = <0>;
spi-max-frequency = <52000000>;
spi-tx-buswidth = <4>;
spi-rx-buswidth = <4>;
spi-cal-enable;
spi-cal-mode = "read-data";
spi-cal-datalen = <7>;
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
spi-cal-addrlen = <5>;
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
mediatek,nmbm;
mediatek,bmt-max-ratio = <1>;
mediatek,bmt-max-reserved-blocks = <64>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "bl2";
reg = <0x0 0x100000>;
read-only;
};
partition@100000 {
label = "u-boot-env";
reg = <0x100000 0x80000>;
};
partition@180000 {
label = "factory";
reg = <0x180000 0x200000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x1000>;
};
};
};
partition@380000 {
label = "bdinfo";
reg = <0x380000 0x40000>;
read-only;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
macaddr_bdinfo_de00: macaddr@de00 {
compatible = "mac-base";
reg = <0xde00 0x6>;
#nvmem-cell-cells = <1>;
};
};
};
partition@3C0000 {
label = "fip";
reg = <0x3C0000 0x200000>;
read-only;
};
partition@5C0000 {
label = "ubi";
reg = <0x5C0000 0x4000000>;
};
};
};
};
&wifi {
nvmem-cell-names = "eeprom";
nvmem-cells = <&eeprom_factory_0>;
status = "okay";
};

View File

@ -75,6 +75,7 @@ mediatek_setup_interfaces()
ucidef_set_interfaces_lan_wan "lan1" eth1
;;
cudy,ap3000outdoor-v1|\
cudy,ap3000-v1|\
cudy,re3000-v1|\
netgear,wax220|\
ubnt,unifi-6-plus|\

View File

@ -73,14 +73,11 @@ case "$board" in
addr=$(mtd_get_mac_binary "Factory" 0x8000)
[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
;;
cudy,tr3000-v1|\
cudy,re3000-v1)
addr=$(mtd_get_mac_binary bdinfo 0xde00)
[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress
;;
cudy,ap3000outdoor-v1|\
cudy,ap3000-v1|\
cudy,m3000-v1|\
cudy,re3000-v1|\
cudy,tr3000-v1|\
cudy,wr3000s-v1|\
cudy,wr3000-v1)
addr=$(mtd_get_mac_binary bdinfo 0xde00)

View File

@ -594,6 +594,23 @@ define Device/cudy_ap3000outdoor-v1
endef
TARGET_DEVICES += cudy_ap3000outdoor-v1
define Device/cudy_ap3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := AP3000
DEVICE_VARIANT := v1
DEVICE_DTS := mt7981b-cudy-ap3000-v1
DEVICE_DTS_DIR := ../dts
SUPPORTED_DEVICES += R49
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 65536k
KERNEL_IN_UBI := 1
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
endef
TARGET_DEVICES += cudy_ap3000-v1
define Device/cudy_m3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := M3000