The various mapping methods are modelled after the requirements of
the Intel GPUs or rather the Mesa driver back end.
With upcoming support for other driver back ends, we need to
sequeeze their requirements in as well. For now hijack 'map_buffer'
to provide for specifying the kind of attributes the client needs.
For now all buffers mapped in the GGTT for Intel GPUs are treated
as RW.
Issue #4265.
This call allows for checking if the given execution buffer has been
completed and complements the completion signal. Initially the GPU
multiplexer always sent such a signal when the currently scheduled
execution buffer has been completed. During enablement of the 'iris'
driver it became necessary to properly check of sequence number.
In case of the Intel GPU multiplexer the sequence numbers are
continous, which prompted the greater-than-or-equal check in the
DRM back end. By hidding this implementation detail behind the
interface, GPU drivers are free to deal with sequence numbers any
way they like and allows for polling in the client, where the
completion signal is now more of a progress signal.
Issue #4265.
The current info implementation (as RPC) is limited in a few ways:
* The amount of data that may be transferred is constrained by the
underlying base platform
* Most information never changes during run time but is copied
nonetheless
* The information differs depending on the used GPU device and
in its current implementation only contains Intel GPU specific
details
With this commit the 'info' RPC call is replaced with the
'info_dataspace' call that transfers the capability for the dataspace
containing the information only. This is complemented by a client
local 'attached_info' call that allows for getting typed access to
the information. The layout of the information is moved to its own
and GPU-specific header file, e.g., 'gpu/info_intel.h'
Issue #4265.
Rather than using the dataspace capability directly, let the client
choose its own local identifier that is linked to the underlying
capability.
Fixes#4265.
Right now the warning about failure to forward packet from driver to
uplink RX connection reads:
"exception while trying to forward packet from driverto Uplink
connection TX"
Add missing space between "driver" and "to".
Issue #4264
32KB is a rather small value. The driver can cope with it now, but
it does not perform as well as it should. This visible especially
in scenarions like nic_router_flood where we still often hit
synchronous wait path. Bump the size to 256kB.
Issue #4264
The problem can be seen when running nic_router_flood scenarion on arm
qemu_virt boards. With the amount of data this scenario tries to send
the driver quickly complains it has failed to push data into TX VirtIO
queue. After this warning message is printed nothing really happens and
after a while the test scenario fails.
The fact that we can't write all available data to the device is not
unexpected. VirtIO queue size is slected at initialization time and we
don't change it during driver lifetime. It can be tweaked via driver
config, but this does not change the fact that we'll always be able to
produce more data packets than we have free space in the VirtIO queue.
IMO the expected behavior of the driver in such case should be to:
1. Notify the device there is data to process.
2. Wait for the device to process at least part of it.
3. Retry sending queued packets.
One could expect returning Transmit_result::RETRY from _drv_transmit_pkt
would produce such result. Unfortunately it seems that Uplink_client_base
treats RETRY return value as indication of link being down. It'll retry
sending the packet only after the device notifies it the link is once
again up. This is the reason why nothing happens when running
nic_router_flood on top of virtio_nic driver. The link never goes down
in this case so once we fill the TX VirtIO queue and tell the base class
to retry the send, we'll be stuck waiting for link up change event
which will never arrive.
To fix this problem, when sending a packet to the device fails, do a
synchrnonus TX VirtIO queue flush (tell device there is data to process
and wait until its done with it).
With this fix in place nic_router_flood test scenario passes on both arm
qemu_virt boards.
Issue #4264
The contents of those descriptor rings can be modified by the device.
Mark them as volatile so the compiler does not make any assumptions
about them.
Issue #4264
This commit contains features and buf fixes:
* Catch errors during resource allocation
* Because Mesa tries to allocate fence (hardware) registers for each
batch buffer execution, do not allocate new fences for buffer objects
that are already fenced
* Add support for global hardware status page. Each context additionally
has a per-process hardware status page, which we used to set the
global hardware status page during Vgpu switch. This was obviously
wrong. There is only one global hardware status page (set once during
initialization) and a distinct per-process page for contexts.
* Write the sequence number of the currently executing batch buffer to
dword 52 of the per-process hardware status page. We use the pipe line
command with QW_WRITE (quad word write), GLOBAL_GTT_IVB disabled
(address space is per-process address space), and STORE_DATA_INDEX
enabled (write goes to offset of hardware status page). This command
used to write to the scratch page. But Linux now uses the first
reserved word of the per-process hardware status page.
* Add Gen9+ WaEnableGapsTsvCreditFix workaround. This sets the "GAPS TSV
Credit fix Enable" bit of the Arbiter control register (GARBCNTLREG)
as described by the documentation this bit should be set by the BIOS
but is not on most Gen9/9.5 platforms. Not setting this bit leads to
random GPU hangs.
* Increase the context size from 20 to 22 pages for Gen9. On Gen8 the
hardware context is 20 pages (1 hardware status page + 19 ring context
register pages). On Gen9 the size of the ring context registers has
increased by two pages to 21 pages or 81.3125 KBytes as the IGD
documentation states.
* The logical ring size in the ring buffer control of the execlist
context has to be programmed with number of pages - 1. So 0 is 1 page.
We programmed the actual number of pages before, leading to ring
buffer execution of NOOPs if page behind our ring buffer was empty or
GPU hangs if there was data on the page.
issue #4260
Increased number of trace subjects since the test sporadically fails on
some platforms.
Also added a sanity check to print an error message in case we run into
the same issue again.
Fixesgenodelabs/genode#4261
The NIC router parses, stores and forwards DNS domain names from DHCP replies.
Yet the routers DHCP client used to not request DNS domain-name information on
DHCP requests. This caused DHCP servers to skip this information on their
replies although it was available. This commit fixes the issue by adding the
DNS domain name code to the request parameter list of requests from the routers
DHCP client.
The 'black_hole' component provides dummy implementations of common
session interfaces.
At this time, only the 'Audio_out' session is provided if enabled
in the configuration of the component:
<config>
<audio_out/>
</config>
Issue #3653
According to spec the tail pointer points to the next qword instructions
which will be used by the software.
p 1354, Doc Ref # IHD-OS-BDW-Vol 2c-11.15
issue #4254
Superpages (2M, 1G) are not supported by now, but partially copied over code
from base-hw was around. Remove unused register definitions and remove
non-working super page code do avoid confusion.
issue #4254
Size argument of ggtt free range check is ignored, which leads to
overlapping allocations inside, which leads to unavailable IO-MEM exceptions
thrown by core.
issue #4254
Both, trace_logger and vfs_trace had their own trace_buffer.h. This
commit consolidates the existing implementations and provides the
resulting trace_buffer.h at 'include/trace/'. It thereby becomes part of
the trace api archive.
genodelabs/genode#4244
If the trace subjects are not properly destructed when the TRACE client
disappears, enabled sources will be owned by a non-existing client.
In other words, when a TRACE client disappears all sources owned by the
client must be disabled.
genodelabs/genode#4247
test-trace always passed, although tracing was never enabled because the
trace subject was not within the first 32 subjects.
* increase number of queried subjects
* output error if trace subject was not found
genodelabs/genode#4247
With this commit, the NIC router DHCP client reads out the first DNS domain
name (DHCP option 15) if any from a DHCP reply that generates an IPv4 config
for a domain and stores the name together with the IPv4 config for that domain.
DNS domain names are reported via the new report tag '<dns-domain>' if the
'config' attribute in the config tag '<report>' is set.
Furthermore, the NIC router DHCP server becomes able to obtain a DNS domain
name from another domain that has a DHCP client dynamically (given the config
attribute 'dns_config_from' is set and no static DNS config is given) or
statically from its configuration (new config tag '<dns-domain>') and propagate
this name with DHCP replies (DHCP option 15).
The 'nic_router_dhcp_*' tests are adapted to test the new feautures.
The commit also gets rid of some mirrored files in
'test/nic_router_dhcp/manager'.
Fixes#4246
WARNING: BREAKS CONFIG COMPATIBILITY!
This commit changes the configuration interface of the NIC router in a way that
may break systems that use the component without proper adjustment!
How to adjust:
At each occurrence of the 'dns_server_from' attribute in a NIC router
configuration replace the attribute name with 'dns_config_from'. The attribute
value remains unaltered.
DETAILED DESCRIPTION
The new attribute name 'dns_config_from' reflects that also other aspects of
the DNS configuration of the denominated domain are used by the DHCP server
that holds the attribute. This commit is a preparation for forwarding also the
domain name (DHCP option 15) with the mechanism behind the attribute.
Ref #4246
The fact that the IPv4 config was a struct with all data members public was a
mere leftover of an early state of the NIC router. Today, the router
implementation style is to avoid structs and public data members wherever
possible.
This commit slightly changes the behavior of the router regarding log output.
The router used to print malformed IPv4 configurations to the log only if
the 'verbose' config flag was set using this style:
! [my_domain] malformed dynamic IP config: interface 10.0.2.1/24 ...
Now, malformed IPv4 configurations are only printed if the
'verbose_domain_state' config flag is set (like with any IP4v configuration
states) using this style:
! [my_domain] dynamic IP config: malformed (interface 10.0.2.1/24 ...)
Fixes#4242
The NIC router DHCP server used to add an extra option 6 field to DHCP replies
for each DNS server address. This conflicts with RFC #2132 section 3.8 which
states that the addresses should be listed within one option 6 field without
delimiter. The discrepancy is fixed by this commit.
Ref #4242
Via a new configuration attribute, the user can decide whether the router
should answer dropped fragmented IPv4 with an ICMP "destination unreachable"
packet and, if so, which value the ICMP code field of this packet should have.
The default is that the router doesn't send such responses (silently dropping
fragmented IPv4). The behavior is tested by the 'nic_router_ipv4_fragm' test.
Fixes#4236
If the new attribute 'dropped_fragm_ipv4' of the <report> tag in the NIC router
config is set "yes", the router will report the number of packets that were
dropped per interface respectively domain because fragmented IPv4 is not
supported. The default is not to report the counter. The behavior is tested by
the 'nic_router_ipv4_fragm' test.
Ref #4236
