Commit Graph

20641 Commits

Author SHA1 Message Date
Milan Krstic
76a629ee35 ath79: ag71xx: preserve port mirror flags during swconfig apply
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.

Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
2019-01-22 09:05:59 +01:00
Hao Dong
62dadcb86c bcm53xx: add support for Phicomm K3
Hardware specifications:

- CPU: Broadcom BCM4709C0 @1.4GHz (Dual-Core ARM)
- RAM: 512 MB (DDR3)
- Flash: 128 MB (NAND)
- LAN ports: 3, LAN speed: 10/100/1000
- WAN ports: 1, WAN speed: 10/100/1000
- 2.4G: BCM4366 4x4 MIMO 1000Mbps -- Skyworks SE2623L 2.4GHz Power Amplifier (x4)
- 5G: BCM4366 4x4 MIMO 2167Mbps -- RFMD RFPA5542 5GHz Power Amplifier Module (x4)
- USB: 1x USB 3.0 port
- 1x LED, 1x reset button, 1x power switch
- 1x system status touch screen

Flash:

- Enter CFE
- Upload the trx file
- Reboot

Signed-off-by: Hao Dong <halbertdong@gmail.com>
2019-01-20 23:34:44 +01:00
Kevin Darbyshire-Bryant
1fdb4a7907 kernel: N_BADCLASS: fix macro to actually work - class e support
Backport upstream patch:

Commit 65cab850f0ee ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.

Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.

Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0ee ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2019-01-19 20:45:49 +00:00
Mathias Kresin
f5e61350e7 ramips: fix firmware splitter for edimax based boards
Use the correct splitter for board with the edimax header.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-19 12:51:04 +01:00
Mathias Kresin
116d0f276d kernel: add DT binding support to the Edimax uImage parser
It allows specifying those parsers directly in the DT.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-19 12:51:04 +01:00
Stijn Tintel
59e62809e6 kernel: remove upstreamed patch from 4.19
This patch applies cleanly, so it doesn't cause errors while rebasing
patches. It results in redifinition of inode_still_linked, causing build
to fail when ubifs is enabled. Drop the patch.

Fixes: a37098a2d0 ("kernel: bump 4.19 to 4.19.16")
Reported-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-17 10:45:31 +02:00
Stijn Tintel
f4ebd1ead0 kernel: drop old symbol from 4.19
CONFIG_LIRC_STAGING was removed in kernel 4.16.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-17 03:09:47 +02:00
Stijn Tintel
a37098a2d0 kernel: bump 4.19 to 4.19.16
Refresh patches.
Remove upstreamed patches:
- backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch
- backport/096-v4.20-netfilter-ipv6-Preserve-link-scope-traffic-original-.patch
- backport/424-v4.20-net-dsa-fix-88e6060-roaming.patch
- hack/100-mtd-rawnand-qcom-fix-memory-corruption-that-causes-p.patch
- pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch
Update patch that no longer applies:
- backport/343-netfilter-nft_flow_offload-handle-netdevice-events-f.patch

Compile-tested: mesongx
Runtime-tested: mesongx

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-17 03:04:13 +02:00
Koen Vandeputte
63a2ed3ba5 kernel: bump 4.9 to 4.9.150
Refreshed all patches.

Remove upstreamed:
- 096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch

Altered patches:
- 024-7-net-reorganize-struct-sock-for-better-data-locality.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-16 12:56:30 +01:00
Koen Vandeputte
5be22ef2fa kernel: bump 3.18 to 3.18.132
Refreshed all patches.

Compile-tested: adm5120
Runtime-tested: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-16 12:56:30 +01:00
Mathias Kresin
26a016731d firmware-utils: mksercommfw: overhaul image creation
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality

Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.

Use a fixed timestamp within the zip archive to make the images
reproducible.

Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.

Beside all changes, the footer still looks wrong in compare to the
netgear update image.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-15 19:11:54 +01:00
Stijn Tintel
8c6f00ef4f kernel: bump 4.14 to 4.14.93
Refresh patches.
Remove upstreamed patches:
- backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch
- pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch
- brcm2708/950-0415-qmi_wwan-apply-SET_DTR-quirk-to-the-SIMCOM-shared-de.patch

Compile-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64
Runtime-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-14 02:20:40 +02:00
Hauke Mehrtens
900c6b1a42 sunxi: Add support for kernel 4.19
This adds supprot for kernel 4.19 to the sunxi target. The patches and
the configuration were copied from the kernel 4.14 patches folder and
adapted for kernel 4.19.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:35:14 +01:00
Hauke Mehrtens
2eeb5d6aac sunxi: Refresh kernel 4.14 configuration
Refresh the sunxi kernel configuration without doing any intentional
changes.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:35:14 +01:00
Hauke Mehrtens
0057beab1b sunxi: Use kernel specific sub target configuration
To make it easier to support multiple kernel versions in parallel also
copy the sub target specific kernel configurations into kernel specific
files.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:20:07 +01:00
Hauke Mehrtens
48f81ee1d0 sunxi: Remove unneeded patches
In the device tree file the higher offsets of the reset controller are
not used, so this patch supporting higher bits is not needed.
The sunxi architecture switched to the simple reset controller with
kernel 4.19 and then this patch does not apply any more.
The sunxi target in OpenWrt is very close to mainline, so if the device
tree files from the mainline Linux kernel need this the mainline kernel
will get support for this.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:20:07 +01:00
Hauke Mehrtens
cfc9bde379 kernel/modules: Add missing config option
This configuration option was added in kernel 4.15 and is missing in the
kernel 4.19 configuration.

Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 17:20:07 +01:00
Hauke Mehrtens
403d36ef3d malta: Add support for kernel 4.19
This adds a kernel configuration file for kernel 4.19 on malta.
CONFIG_POWER_RESET_PIIX4_POWEROFF and CONFIG_POWER_RESET_SYSCON were
activated because malta now uses this driver for reboot.

CONFIG_BLK_DEV_SR was also added because it was also added to the kernel
default configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 16:31:40 +01:00
Hauke Mehrtens
4ab689c137 malta: Refresh kernel 4.14 configuration
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 16:31:38 +01:00
Hauke Mehrtens
c54e4747be kernel: MIPS: Add CPU option reporting to /proc/cpuinfo
Many MIPS CPUs have optional CPU features which are not activates for
all CPU cores. Print the CPU options which are implemented in the core
in /proc/cpuinfo. This makes it possible to see what features are
supported and which are not supported. This should cover all standard
MIPS extensions, before it only printed information about the main MIPS
ASEs.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 16:24:50 +01:00
Hauke Mehrtens
c7102a7699 kernel/modules: Fix build of kmod-pmbus
This fixes two build problems introduced with the recently added new
kernel module package.

Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-13 13:16:02 +01:00
Chuanhong Guo
bd03255ec4 generic: ar8216: ar8327: kill warnings
This fixed warnings caused by returning value in a void function

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-01-13 12:25:30 +01:00
David Bauer
97e4311fca mpc85xx: add support for Sophos RED 15w Rev.1
Hardware
========
CPU:  Freescale P1010 PowerPC
RAM:  128M DDR3
NAND: 128MiB
ETH:  RTL8211F SGMII PHY
      RTL8367B 5-port RGMII switch
      (not connected to SoC - unmanaged)
WiFi: SparkLan WPEA-121N
       - Atheros AR9382 2T2R abgn
USB:  1x USB 2.0
LED:  System, Router, Internet, Tunnel controllable
      LAN1-4, WAN, Power non-controllable
BTN:  None

Installation
============
1. Power on the device while attached to the Console port.

2. Halt the U-Boot by pressing Enter when prompted.

3. Set the correct bootcmd for booting OpenWRT:
 > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200"
 > setenv bootcmd "run bootargs_owrt;
   nand read 0x1000000 0x300000 0x800000;
   bootm 0x1000000;"
 > saveenv

5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a
   TFTP server root-directory served on 192.168.1.2/24. Connect your
   computer to one of the LAN-ports.

4. Boot OpenWRT initramfs image with
 > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin;
   bootm 0x1000000;

6. (Optional)
   Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case
   you ever want to go back to the vendor firmware.

7. Create Ubi Volume on mtd4 by executing
 > ubiformat /dev/mtd4 -y

8. Transfer OpenWRT sysupgrade image to the device via SCP and install it
   with
 > sysupgrade -n <openwrt-image-file>

Back to Stock
=============
If you want to go back to the stock firmware, here is the bootcmd of the
vendor firmware:
 > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5;
   nand read 0xc00000 0x00300000  0x100000;
   nand read 0x1000000 0x00400000 0x00800000;
   bootm 0x1000000 - 0xc00000

Set it via 'setenv' from the U-Boot shell and don't forget to save it
using 'saveenv'!

After this, boot the OpenWRT initramfs image just like you would for
installation. Write back the three vendor partitions using mtd. Reboot
the device afterwards.

Signed-off-by: David Bauer <mail@david-bauer.net>
[refresh and reorder patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-13 11:31:43 +01:00
Christian Lamparter
85be0f4c21 apm821xx: 4.14: sync config
This patch syncs the 4.14 kernel config to the
current generic configuration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-13 11:31:43 +01:00
Pawel Dembicki
46d4c09bb6 mpc85xx: disable initramfs image in TL-WDR4900
Initramfs image isn't required for this device and regular
initramfs generation isn't work properly. It create not working
binaries.

This patch disable initramfs image for TL-WDR4900.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-01-13 11:31:43 +01:00
Pawel Dembicki
5de6aed42c mpc85xx: add support for Freescale (NXP) P2020RDB
This commit add initial support for Freescale (NXP) P2020RDB

Hardware:
SoC: P2020 2x1GHz
DRAM: 512-1GB DDR3
2 + 4 GBE (2 separate ports and four in VSC7385)
Flash: 16MB NOR, 32MB NAND, 16MB SPI-NOR
PCIE x1 and mPCIE x1
SD Reader

Interfaces:
GBE RJ45 x6
USB2.0 x1
UART x2
I2C x2
JTAG x1
SD x1
PCIE x2 (PCIE and mPCIE)

Flash instructions:
Place sysupgrade image to 0x80000 address in NOR.
Eg. (no brakelines in setenv command):

setenv 'firmware_flash tftpboot $loadaddr $firmwarefile;
 protect off $norfdtaddr +$filesize; erase $norfdtaddr +$filesize;
 cp.b $loadaddr $norfdtaddr $filesize; protect on $norfdtaddr +$filesize;
 cmp.b $loadaddr $norfdtaddr $filesize'
setenv firmwarefile firmware.bin
run firmware_flash

Boot (no brakeline in setenv command):
setenv bootcmd 'setenv bootargs root=/dev/mtdblock3 rw console=$consoledev,
$baudrate rootfstype=squashfs $othbootargs;
bootm $norfdtaddr'
saveenv
boot

Known issues:
-Switch is unmanaged (VSC 7385 is connected via eLBC, driver uses SPI)
-No SD reader support

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [refreshed patches]
2019-01-13 11:31:43 +01:00
Pawel Dembicki
ed2839ac41 kernel/modules: add kmod-pmbus-zl6100 module
This patch adds the kmod packaging for the Intersil / Zilker Labs
ZL6100 and compatible digital DC-DC controllers as well as the
core kernel module for the Power Management Bus.

Add:
kmod-pmbus-core
kmod-pmbus-zl6100

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-01-13 11:07:37 +01:00
Hauke Mehrtens
75fdf3ba01 x86: Add support for kernel 4.19
This adds initial support for kernel 4.19 to the x86 target.
The patches and the kernel configurations were copied from kernel 4.14
and then refreshed.

The legacy and the genode target will not support PAE any more because
they use a CPU type which does not support PAE, the generic sub target
still supports PAE.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-12 22:40:36 +01:00
Hauke Mehrtens
f6e0ecdceb x86: Refresh kernel 4.14 configuration
This refreshes the kernel configuration for kernel 4.14.
First this was run for the legacy target:
	make kernel_oldconfig
Then for all targets including the legacy target this was run:
	make kernel_oldconfig CONFIG_TARGET=subtarget
The option CONFIG_104_QUAD_8 was added to the generic configuration
because it would have been automatically removed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-12 22:40:12 +01:00
Hauke Mehrtens
0ea7160abe x86: Use kernel specific subtarget configurations
This makes it possible to use different sub target configurations for
kernel 4.19 for example.
To support kernel 4.9 and kernel 4.14 with the same configuration file
already needed some extra work this will not be needed for kernel 4.19
any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-01-12 22:39:41 +01:00
Hans Dedecker
4bd9d331e5 octeon: fix typo in platform.sh
Fix upgrade typo

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2019-01-12 19:40:13 +01:00
Rafał Miłecki
45ce9897c0 kernel: add bcma fix for subdevices DMA parameters
This fixes bgmac DMA allocations with kernel 4.19.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-11 07:33:56 +01:00
Rafał Miłecki
34696ce25e kernel: backport bcma patches that improve printing functions
Updated printing functions use dev_* helpers to provide more meaningful
messages.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-10 16:47:43 +01:00
Rafał Miłecki
7175b1356e brcm47xx: backport MIPS fix adding struct device for the SoC
It's needed to:
1) Fix GPIOLIB_IRQCHIP as in 4.19 there is no bcma revert anymore
2) Fix /sys/devices/
3) Fix dma_zalloc_coherent() regression

It still needs a bcma change that will follow later.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-10 06:57:19 +01:00
Rafał Miłecki
94561333cd brcm47xx: backport a final/accepted Netgear WNDR3400v3 patch
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-01-10 06:35:57 +01:00
Koen Vandeputte
630d8b87a5 cns3xxx: use actual size reads for PCIe
upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(),
which preserved the property of only doing 32-bit reads.

It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.

Due to:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended

It makes perfectly sense to also swap 32 bit reading in favor of actual size.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
Koen Vandeputte
f56a4e809b kernel: bump 4.14 to 4.14.91
Refreshed all patches.

Removed upstreamed:
- 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
Koen Vandeputte
30d518bf16 kernel: bump 4.9 to 4.9.148
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch

Removed upstreamed:
- 424-v4.20-net-dsa-fix-88e6060-roaming.patch

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
Koen Vandeputte
a18f68ff30 kernel: bump 3.18 to 3.18.131
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
John Crispin
93c35bfa21 ramips: whitespace cleanup inside hnat driver
Signed-off-by: John Crispin <john@phrozen.org>
2019-01-07 15:45:51 +01:00
HsiuWen Yen
6b9bdbd493 ramips: add two-way hashing scheme for MT7621
Sometimes the tuples might be hashed to the same FOE entry.
When this hash collision problem occurs, some of the
connections will not be bound and consequently the CPU
idle rate cannot reach 100%. Therefore, two-way hashing
is adopted to alleviate this problem.

Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
2019-01-07 15:40:51 +01:00
David Bauer
634c733065 ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGE
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.

Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.

This fixes eva-image generation using the OpenWRT image-builder.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-06 12:26:12 +01:00
Christian Lamparter
bbe7ad5a2f mpc85xx: 4.19: refresh kernel config
This patch syncs the 4.19 kernel config to the
current generic configuration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 23:36:39 +01:00
Christian Lamparter
32420fc6b9 mpc85xx: 4.14: refresh kernel config
This patch syncs the 4.14 kernel config to the
current generic configuration.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 23:36:39 +01:00
Robert Marko
bba1428274 ipq40xx: 4.14: Sync kernel config
This patch syncs the 4.14 kernel config to the
current generic configuration.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 22:23:41 +01:00
Robert Marko
0c1f1dab59 ipq40xx: 4.19: Sync kernel config
This patch syncs the 4.19 kernel config since the
KERNEL_STACKPROTECTOR and compiler options are
now part of the 4.19 generic config.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 22:23:41 +01:00
Christian Lamparter
32e953b821 ipq40xx: fix 4.14 ImageBuilder build woes
Robert Marko reported an issue with the current imagebuilder images:
"Imagebuilder includes the new kmod-usb-dwc3-qcom USB driver
package by default even on 4.14. [...] the current state imagebuilder
can't build images under 4.14 at all as the kmod-usb-dwc3-qcom does
not exist in it so it throws and error and exits."

This patch reverts the Makefile to just kmod-usb-dwc3-of-simple and
once the switch to 4.19 is done. It also removes the
kmod-usb-phy-qcom-dwc3 as they only contain the usb-phy drivers for
the ipq806x generation.

Dynamic switching based on the KERNEL_PATCHVER is possible by using:
   $(if $(filter 4.14,$(KERNEL_PATCHVER)),kmod-usb-dwc3-of-simple,kmod-usb-dwc3-qcom)
though it

Fixes: 13321fa142 ("ipq40xx: Use kmod-usb-dwc3-qcom by default")
Fixes: 6e58fb2c33 ("ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom")
Reported-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 22:23:10 +01:00
Christian Lamparter
3801f8a7f7 apm821xx: MBL: fix kernel/apollo3g.dtb artifact build
The name for the artifact should have been apollo3g.dtb
and not kernel.dtb.

Fixes: 908bdbfce9f9 ("apm821xx: utilize build ARTIFACTs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 22:09:08 +01:00
Pawel Dembicki
36d45e4cdc mpc85xx: add kernel 4.19 support
Copied config from 4.14

Add patches for 4.19

Drop patch 103-powerpc-fix-build-cross32ar.patch,
because issue was fixed in upstream.

Compiled: generic p1020
Compiled and tested: (unofficial) P2020, TP-Link TL-WDR4900

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 22:09:08 +01:00
Pawel Dembicki
576c69938b mpc85xx: tl-wdr4900-v1: convert to mtdsplit image
Currently, the image creation process for the TP-Link tl-wdr4900-v1
needs a fixed sized kernel and places the rootfs partition at a
fixed offset. With the upcoming move to 4.19 the kernel will no
longer fit into the existing allocated space for the kernel
partition.

This patch converts the device to utilize the established
tplink,firmware mtdsplitter, which can deal with a dynamic
kernel/rootfs size.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 21:59:52 +01:00
David Bauer
c8115167f9 ath79: add support for devolo WiFi pro 1200i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
David Bauer
8d68be8057 ath79: add support for devolo WiFi pro 1750i
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-05 21:55:22 +01:00
Anton Arapov
6ba58b7b02 ramips: cleanup the RB750Gr3 support
Always enable the pwr led and use the usr led for boot status indication.

Rename nodes in the dts, to match what is recommend in the devicetree
specification.

Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io
which isn't required on mt7621.

Use the BTN_0 keycode for the mode button. This board doesn't have any
wireless.

Use a more descriptive label for the reset button and the GPIO enabling
the usb vcc supply.

Use the beeper kernel module for the buzzer.

Fix the pinmux to switch only pins used as GPIOs to the GPIO function.
Add support for the PoE enable GPIO to the userspace. The PoE power
status can be read via GPIO7. Since OpenWrt doesn't have support for
reading inputs from userspace, prepare only the pinmux for the GPIO.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Anton Arapov
52f2d7d2a9 ramips: add RB750Gr3 native support
This patch adds support of MikroTik RouterBOARD 750Gr3, without the need
to reflashing the bootloader.

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

Since the image isn't compatible with RouterBOARD 750Gr3 installations
which have replaced the bootloader, the former used userspace boardname
is not added to the SUPPORTED_DEVICES, to prevent a brick while trying
to upgrade to the image with native support.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Paul Wassi
eb1887be93 ath79: merge cases in 02_network
Merge some duplicate cases in /etc/board.d/02_network

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-01-02 22:36:27 +01:00
Alberto Bursi
9c4f903999 x86: enable kmod-bnx2 on 64-bit by default
Gigabit ethernet adapters using BCM5706/5708/5709/5716 chipset are
common on servers and as easy/cheap to get as Intel based ones.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2019-01-02 22:12:19 +01:00
Roger Pueyo Centelles
359f5e5390 kernel: mtd: add support for EN25QH64 in spi-nor.c
The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip. Its 32, 128 and
256 Mbits siblings are supported upstream but this particular size wasn't.
This commit includes patches for kernels 4.14 and 4.19.

Tested on a COMFAST CF-E120A v3 (ath79).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-01-02 22:12:19 +01:00
Christoph Krapp
59b99e1924 ath79: align GL-AR750S boardname to other GL.iNet devices
As the official device name is GL-AR750S, rename the board accordingly.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-01-01 19:42:41 +01:00
Christian Lamparter
257de1b01f apm821xx: sata: boot-part feature integration
This patch adds the boot-part feature to the apm82181 sata target.
This makes it possible to configure the boot partition size with
the generic CONFIG_TARGET_KERNEL_PARTSIZE symbol.

Please note: For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value can cause
sysupgrade to repartition the device!

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-01 16:39:59 +01:00
Christian Lamparter
7d009d8e6a apm821xx: use bin file extension for sysupgrade-tar images
Use the file extension bin for sysupgrade-tar images with
metadata to unify the file extension across the target/tree.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-01 16:39:59 +01:00
Christian Lamparter
2271967f57 apm821xx: utilize build ARTIFACTs
The exported kernel dtbs can be build as artifacts.
This way, the MyBook Live's DTB is not generated twice.

While at it, give the artifacts their proper name.
For the wndr4700 use the "device-tree" partition name and
for the MyBook Live: "apollo3g.dtb" to match the mbl_boot.scr.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-01 16:39:59 +01:00
INAGAKI Hiroshi
51fe956c4f ipq806x: add support for Buffalo WXR-2533DHP
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.

The U-Boot on WXR-2533DHP employs a complicated dual firmware
protection scheme against corruptions of the kernel and rootfs
images. See the notes in buffalo.sh for details.

specifications:

- Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T)
- 512 MB of RAM (DDR3)
- 256 MB of Flash (NAND)
- 4T4R 2.4/5 GHz Wlan (QCA9980)
- 5x 10/100/1000 Mbps Ethernet
- 10x LEDs, 8x keys (6x buttons, 2x slide-switches)
- 2x USB 3.0 Type-A
- 12VDC/4A AC Adapter
- UART through-hole on PCB
  - J3: Vcc, GND, TX, RX from USB port side
  - 115200n8

Boot instructions for the initramfs image:

1. Prepare the TFTP server with the initramfs image renamed to
   "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10".
2. Press the "AOSS" button while powering on the WXR-2533DHP.
3. Wait until the "Wireless" LED flashes before releasing the AOSS button.
   The WXR-2533DHP will grab the image from TFTP server and will boot it.

Flashing instructions:

To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to
let it finish the flashing process.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
2019-01-01 16:39:59 +01:00
INAGAKI Hiroshi
250f5ec139 ipq806x: add ramdisk feature
This commits adds the "ramdisk" feature to ipq806x target. The
main driving force behind this decision is to facilitate the
installation of OpenWrt on some locked IPQ806x devices.

Examples:

- NEC Aterm WG2600HP

  The U-Boot on WG2600HP is protected with a password which prevents
  users from gaining access to the u-boot prompt in order to install
  the images from there.

  Therefore, on this device, installing OpenWrt by the user involves
  changing the bootcmd as follows so that WG2600HP downloads and
  executes initramfs image from TFTP server.

  ex.:
    bootcmd="ping ${serverip} && tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq"

- Buffalo WXR-2533DHP

  The U-Boot on WXR-2533DHP has built-in firmware recovery mode.
  It's activated by holding the "AOSS" button during boot. This
  will trigger the device to download the firmware from an TFTP
  server and booting from it. By using this, the user  can the
  install OpenWrt firmware without having access to the UART
  console.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-01 15:40:13 +01:00
Christian Lamparter
6734753ef4 kernel: Add missing symbols to 4.19
Tested with apm82181 and ipq40xx minimal image versions.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-01 15:40:13 +01:00
Paul Wassi
54e3ee0215 ath79: fix case statement in 01_leds
Fix a missing 'end-of-case' recently introduced in 01_leds

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2019-01-01 01:38:51 +01:00
Mathias Kresin
8c485fbb25 ath79: rework elecom-header recipe
Replace the code with a more readable version. Rename the recipe
to reflect the real usecase.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 16:48:49 +01:00
Paul Wassi
28a5674e33 treewide: fix spaces vs. tabs
Fix spaces vs. tabs issues in ath79 and ramips.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 16:37:20 +01:00
Rosy Song
1c39dcc2bb ath79: tweak the position of factory partition for wr818
The 'factory' partition will move to 0x50000-0x60000 in 2019. As
the webserver in bootloader is compatible with different mtdlayout,
all the users still can upgrade firmware whatever on ath79 or ar71xx.

Signed-off-by: Rosy Song <rosysong@rosinson.com>
2018-12-31 16:37:09 +01:00
Roger Pueyo Centelles
3dfc07d186 ath79: add support for COMFAST CF-E110N
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.

Specifications:

 - 650/400/216 MHz (CPU/DDR/AHB)
 - 2x 10/100 Mbps Ethernet, both with PoE-in support
 - 64 MB of RAM (DDR2)
 - 16 MB of FLASH
 - 2T2R 2.4 GHz, up to 26 dBm
 - 11 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1) and GPIO (J9) headers on PCB

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new want, so a factory reset will be
 needed: once the new firmware is flashed, perform the factory reset by
 pushing the reset button several times during the boot process, while the
 WAN LED flashes, until it starts flashing quicker.

 The U-boot bootloader contains a recovery HTTP server to upload the
 firmware. Push the reset button while powering the device on and keep it
 pressed for >10 seconds. The recovery page will be at http://192.168.1.1

Notes:

 The device is advertised, sold and labeled as "CF-E110N", but the
 bootloader and the stock firmware identify it as "v2".

Acknowledgments:

 Petr Štetiar <ynezz@true.cz>
 Sebastian Kemper <sebastian_ml@gmx.net>
 Chuanhong Guo <gch981213@gmail.com>

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 16:25:11 +01:00
Georgi Vlaev
d03aae1a09 ath79: add support for TP-Link Archer C6 v2
This patch adds support for TP-Link Archer C6 v2 (EU)

Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) QCA9563 integrated (3x3)
  - 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board

Flash instructions:

Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
   tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
   button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing

According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
2018-12-31 16:25:11 +01:00
Guan-Hong Lin
9ebb44aef4 ath79: add support for EnGenius EWS511AP
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.

Short specification:

- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
   (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
   (ath)> erase 0x9f060000 +f50000
   (ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
   (ath)> reset

Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
2018-12-31 16:25:09 +01:00
Paul Wassi
48745221a8 ath79: add status LED on GL.iNet AR300M
This adds the triggers for the status LED of this device.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:24:55 +01:00
Paul Wassi
6e78d546d1 ath79: fix boardname of GL.iNet GL-AR300M
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 14:24:21 +01:00
Paul Wassi
cdbf2de777 ath79: Add support for TP-Link WR810N
Device specifications given in b23b0fb28b

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:18:19 +01:00
Paul Wassi
c2ecec07cc ath79: Add GL.iNet AR150 LED triggers
When switching from ar71xx to ath79 the default netdev LED
triggers for LAN and WAN got lost.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:05:26 +01:00
Paul Wassi
8ba76d6e74 ath79: fix boardname of GL.iNet GL-AR150
This device is called GL-AR150, therefore rename the board
to 'gl-ar150'

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 14:05:26 +01:00
INAGAKI Hiroshi
caf306ce91 ath79: add support for ELECOM WRC-1750GHBK2-I/C
ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac
routers, based on Qualcomm Atheros QCA9563.

This commit also includes small fix; use "0x0x03000101" as pll_1000
instead of "0x03000000".

Specification:

- SoC:      Qualcom Atheros QCA9563
- RAM:      128 MB (DDR2)
- Flash:    16 MB (SPI-NOR)
- WLAN:     2.4/5 GHz
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz:   3T3R (QCA9880)
- Ethernet: 10/100/1000 Mbps
- LED/key:  4x/3x (2x buttons, 1x slide-switch)
- UART:     through-hole on PCB
  - Vcc, RX, GND, TX from switch (QCA8337N) side
  - 115200n8

Flash instruction using factory image:

1. Boot WRC-1750GHBK2-I/C normaly
2. Access to "http://192.168.2.1/" and open firmware upgrade page
("ファームウェア更新 手動更新(アップデート)")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, perform sysupgrade with
squashfs-sysupgrade image
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-31 21:38:53 +09:00
Paul Wassi
ab12913676 ath79: Fix UBNT Unifi AC LEDs
Both LEDs on these devices are ACTIVE_HIGH, change back to what
it is on ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 13:28:31 +01:00
Paul Wassi
31dc0fbca3 ath79: Fix system LED on TP-Link WR740/741 v4
The system LED on these devices is ACTIVE_LOW, change back to what
it is on ar71xx.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-12-31 13:28:31 +01:00
Antonio Silverio
9601d94138 ath79: add support for TP-Link TL-WR841N/ND v8
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset

Installation:
Upload the factory image via the vendor-GUI.

Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:31 +01:00
David Bauer
98f826fdc0 ath79: use caldata patching for Archer C58/C59
With this commit the TP-Link Archer C58 and Archer C59 use caldata
patching in order to set the correct 5GHz MAC-address.

Tested on TP-Link Archer C59 v1.

For more details see commit 330965b.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-31 13:28:31 +01:00
Christoph Krapp
af28d8a539 ath79: add support for GL.iNet GL-AR750S
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.

Furtheremore support for the MicroSD port is not implemented as of now.

Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
  - Another LED can be accessed on GPIO 7 if soldered

Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-31 13:28:20 +01:00
David Bauer
06b1a6e885 ath79: fix OCEDO Koala ethernet configuration
The OCEDO Koala has incorrect PLL settings which result in ~3% packet
loss on ethernet connections.

Also omit the gmac-configuration as it's incorrect too.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-30 20:08:13 +01:00
Weijie Gao
abc7ed2c58 ath79: add support for D-Link DIR-859 A1
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880

USB is supported on the PCB but not connected.

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or the u-boot
   failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted. Otherwise the u-boot
   will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the firmware
   checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
   upgrade the factory.bin through the u-boot failsafe interface and then goto
   step 2.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Mathias Kresin
fd35c5b205 build: move seama commands to image-commands.mk
Move it to image-commands.mk to get rid of duplicate recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Mathias Kresin
de42466528 ar71xx: sync seama image build code with ramips
Use the same syntax as used in the ramips target, to use common seama
recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Mathias Kresin
7c1332d95f ramips: consolidate seama image build code
Create a common template which has the required image build code
defined. Add some new variables to pass individual parts to the seama
recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:12 +01:00
Jonas Gorski
a01568fbd3 brcm63xx: remove broken DSP platform device code
There is no driver and it crashes the kernel, so just remove it.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-12-30 13:22:13 +01:00
Jonas Gorski
d09561f73d brcm63xx: fix bcm6348 pinmux group selection
The mask/shift computation used the pin group number instead of the pin
number, resulting in always modifying group 4 when applying muxes, so
fix it to consistently use the pin number.

Fixes: 0755c2d117 ("brcm63xx: add pinctrl support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-12-30 13:22:13 +01:00
Daniel Gonzalez Cabanelas
33bff49a31 brcm63xx: VH4032N: add the SPROM fixups
Add the SPROM fixups for the onboard BCM43222 wifi on the Observa
VH4032N

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2018-12-30 13:22:13 +01:00
Jonas Gorski
6d6127e537 brcm63xx: fix gpio hogs on gpio/pinctrl nodes
Work around a chicken/egg issue in registration of dual gpio/pinctrl
nodes.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-12-30 13:21:42 +01:00
Jonas Gorski
1789202ed4 brcm63xx: rename switch core reset patch to 0xx as it has been accepted
The core reset fix was accepted upstream, so move it to its right place.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-12-30 13:20:57 +01:00
Eduardo Barros
335c69fbb2 ath79: Fix wrong TL-WR740N v4 switch port order
Fix the switch port order to have the correct order in LuCI.

Fixes: FS#1469

Signed-off-by: Eduardo Barros <geadas@gmail.com>
[trim commit title, add a proper commit message, add fixes tag, keep
alphabetical order of the blocks]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-29 16:12:41 +01:00
Deng Qingfang
5580a9dd31 ramips: add support for GeHua GHL-R-001
Specs
	SoC: MT7621AT
	RAM: 512MiB
	Flash: 32MiB MX25L25635F SPI NOR
	2.4G: MT7603EN
	5G: MT7612EN
	Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
	USB 3.0
	LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
	      The last two ones are controlled by GPIO
	UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
	      UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
	      The stock u-boot uses UARTLITE1 by default. Baud rate is 57600

Flash instruction
	1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
	   One can alternatively use UART to log in
	2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
	   One can alternatively download the firmware via wget through Internet
	3. mtd write /path/to/openwrt.bin firmware
	4. reboot

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-29 16:03:30 +01:00
Deng Qingfang
0599cd90e1 ramips: fix MT7621 dtsi
Fix SysTick reg
Add uartlite2 and uartlite3 nodes

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-29 16:03:30 +01:00
Simon Quigley
9f0e233576 ramips: add support for DLINK DWR-922-E2
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui, or via recovery interface:

How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
    LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
    one manually
3.) Upload original factory image via JBOOT http interface at IP
    192.168.123.254
4.) If http doesn't work, it can be done with curl command:
      curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
    upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
    type "reboot" into the telnet session.

Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-29 16:03:30 +01:00
Christian Lamparter
cb0f39c9cd kernel: fix f2fs on big endian machines
The WD MyBook Live SquashFS images didn't work anymore due to
a upstream regression in f2fs commit: 0cfe75c5b01199
("f2fs: enhance sanity_check_raw_super() to avoid potential overflows")
that got backported to 4.14.86 and landed in 4.18.

by Martin Blumenstingl:
|Treat "block_count" from struct f2fs_super_block as 64-bit little endian
|value in sanity_check_raw_super() because struct f2fs_super_block
|declares "block_count" as "__le64".
|
|This fixes a bug where the superblock validation fails on big endian
|devices with the following error:
|  F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
|  F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
|  F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
|  F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
|As result of this the partition cannot be mounted.
|
|With this patch applied the superblock validation works fine and the
|partition can be mounted again:
|  F2FS-fs (sda1): Mounted with checkpoint version = 7c84
|
|My little endian x86-64 hardware was able to mount the partition without
|this fix.
|To confirm that mounting f2fs filesystems works on big endian machines
|again I tested this on a 32-bit MIPS big endian (lantiq) device.

Hopefully, this will do until Martin's patch moved through upstream
to -stable.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-29 13:41:35 +01:00
Christian Lamparter
eb43efa997 apm821xx: fix MBL DUO SUPPORTED_DEVICES compat id
The MyBook Live DUO used "wd,mybooklive-duo" as the first
compatible string and not "wd_mybooklive-duo".

Fixes: 9b47aa93c7 ("apm821xx: unify My Book Live Single + Duo images")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-29 13:38:53 +01:00
Andreas Ziegler
d492da702a ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526
This fixes the 5GHz WiFi LED which was previously not working.

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
2018-12-29 12:35:47 +01:00
David Bauer
97dc323a4c ath79: fix Archer A7 v5 5GHz MAC adress
Currently all Archer A7 v5 have the same (incorrect) MAC address.
The address is currently derived from eth1 which is not present on the
QCA9563. Use eth0 to get the correct MAC address.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-29 12:35:47 +01:00
Weijie Gao
74af8a833a ramips: add support for CreativeBox v1
Hardware:
SoC: MT7621
DRAM: 512MB DDR3
Flash: 32MB SPI-NOR
WiFi 2.4GHz: MT7603 @ PCIe0
WiFi 5.8GHz: MT7612 @ PCIe1
SATA: ASM1061 @ PCIe2

Interfaces:
GBE RJ45 x5
USB3.0 x1
eSATA (with USB2.0) x1
SATA x1
UART x1
I2C x1
JTAG x1

Flash instructions:
Through factory bootloader or firmware web interface

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-12-28 12:45:23 +01:00
NOGUCHI Hiroshi
d020ae79ab ramips: add SPDX license identifier into some dts,dtsi
Acked-by: Mathias Kresin <dev@kresin.me>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
2018-12-28 12:45:23 +01:00
Christian Lamparter
e59a6c8d4c apm821xx: switch MyBook Live's recovery images to multi-file
This patch converts the MyBook Live's recovery image to utilize the
multi-image method which integrates the device-tree binary directly
into the image.

The new initramfs can be loaded through the MyBook Live's U-boot
in the following way:

=> setenv ipaddr 192.168.1.1
=> setenv serverip 192.168.1.2
=> sata init; run addtty; tftp $kernel_addr_r wd_mybooklive-initramfs.bin; bootm
   Waiting for PHY auto negotiation to complete... done
   ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0)
   Using ppc_4xx_eth0 device
   TFTP from server 192.168.1.2; our IP address is 192.168.1.1
   Filename 'wd_mybooklive-initramfs.bin'.
   Load address: 0x1000000
   Loading: ################################################ [...]
   done
   [...]
   Booting kernel from Legacy Image at 01000000 ...
      Image Name:    initramfs
      Image Type:   PowerPC Linux Multi-File Image (gzip compressed)
   [...]

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-28 00:45:57 +01:00
Christian Lamparter
4cd533411e apm821xx: 4.14: switch to upstream dw-dma-hport patch
This patch fixes the build regression on 4.14 build
due to dt-bindings/dma/dw-dmac.h MIA.

apm82181.dtsi:24:10: fatal error: dt-bindings/dma/dw-dmac.h: No such file or directory

Fixes: 32141c183a ("apm821xx: add linux 4.19 apm821xx patches")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 23:08:01 +01:00
Rafał Miłecki
25d8aa7d02 brcm47xx: add support for the kernel 4.19
One patch that wasn't ported due to a lot of conflict is:
901-Revert-bcma-switch-GPIO-portions-to-use-GPIOLIB_IRQC.patch

Hopefully a correct/real fix will get developed before we switch
brcm47xx to the 4.14.

This IS NOT ready for switching/trying/using 4.19 yet due to some DMA
regression affecting bgmac:
[    0.945472] bgmac_bcma bcma0:2: Found PHY addr: 25
[    0.954565] libphy: bcma_mdio mii bus: probed
[    0.959486] ------------[ cut here ]------------
[    0.964387] WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 bgmac_enet_probe+0x1b4/0x5c4
[    0.973751] Modules linked in:
[    0.976913] CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.9 #0
[    0.982750] Stack : 804a0000 804597c4 00000000 00000000 80458fd8 8381bc2c 838282d4 80481a47
[    0.991367]         8042e3ec 00000001 804d38f0 00000204 83980000 00000065 8381bbe0 6f55b24f
[    0.999975]         00000000 00000000 80520000 00002018 00000000 00000075 00000007 00000000
[    1.008583]         00000000 80480000 000ee811 00000000 00000000 00000000 80432c00 80248db8
[    1.017196]         00000009 00000204 83980000 803ad7b0 00000000 801feeec 00000000 804d0000
[    1.025804]         ...
[    1.028325] Call Trace:
[    1.030875] [<8000aef8>] show_stack+0x58/0x100
[    1.035513] [<8001f8b4>] __warn+0xe4/0x118
[    1.039708] [<8001f9a4>] warn_slowpath_null+0x48/0x64
[    1.044935] [<80248db8>] bgmac_enet_probe+0x1b4/0x5c4
[    1.050101] [<802498e0>] bgmac_probe+0x558/0x590
[    1.054906] [<80252fd0>] bcma_device_probe+0x38/0x70
[    1.060017] [<8020e1e8>] really_probe+0x170/0x2e8
[    1.064891] [<8020e714>] __driver_attach+0xa4/0xec
[    1.069784] [<8020c1e0>] bus_for_each_dev+0x58/0xb0
[    1.074833] [<8020d590>] bus_add_driver+0xf8/0x218
[    1.079731] [<8020ef24>] driver_register+0xcc/0x11c
[    1.084804] [<804b54cc>] bgmac_init+0x1c/0x44
[    1.089258] [<8000121c>] do_one_initcall+0x7c/0x1a0
[    1.094343] [<804a1d34>] kernel_init_freeable+0x150/0x218
[    1.099886] [<803a082c>] kernel_init+0x10/0x104
[    1.104583] [<80005878>] ret_from_kernel_thread+0x14/0x1c
[    1.110107] ---[ end trace f441c0d873d1fb5b ]---
[    1.114914] bgmac_bcma bcma0:2: Allocation of TX ring 0x200 failed
[    1.121215] bgmac_bcma bcma0:2: Unable to alloc memory for DMA
[    1.127626] bgmac_bcma: probe of bcma0:2 failed with error -12
[    1.133838] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-27 22:12:15 +01:00
Petr Štetiar
6ab138fa84 ath79: ubnt-bullet-m-xw: Remove eth1 disabled node
It's redundant as eth1 is disabled by default in ath79.dtsi.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:25 +01:00
Petr Štetiar
74f46d90be ath79: ubnt-bullet-m-xw: Move eth0 mtd-mac-address to the common include
It's same for Bullet and Nanostation so far, so let's hope it's going to
be the same for other boards sharing the same platform.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:25 +01:00
Petr Štetiar
6935d73851 ath79: ubnt-bullet-m-xw: Remove pll-data property from eth0 node
It's not necessary as it's already defined in ar934x.dtsi to:

  pll-data = <0x16000000 0x00000101 0x00001616>;

And in ar71xx it's currently set to the same values:

 #define AR934X_PLL_VAL_1000	0x16000000
 #define AR934X_PLL_VAL_100	0x00000101
 #define AR934X_PLL_VAL_10	0x00001616

And dumping the value from the airOS v6.1.7 has the same value:

  AR934X_PLL_ETH_XMII_CONTROL_REG 0x1805002C 0x101

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:24 +01:00
Petr Štetiar
965ce07dbb ath79: ubnt-xw: Add LED aliases for diag and status LED support
Currently there is no LED signalization for various system states
implemented in diag.sh, so this patch adds support for it.

Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-27 16:02:23 +01:00
Christian Lamparter
32141c183a apm821xx: add linux 4.19 apm821xx patches
This patch updates the apm821xx target to use the 4.19 kernel.

4.19 ships with all the crypto4xx driver patches. Furthermore,
the DW-DMA fix for the SATA controller has been backported from
4.20 and integrated.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
96d55f9fd9 kernel: 4.19: fix usbport led trigger regression
|In the patch "usb: simplify usbport trigger" together with
|"leds: triggers: add device attribute support" caused an
|regression for the usbport trigger. it will no longer
|enumerate any "ports" (i.e the sysfs directory stays empty)
|if the usb host drivers are fully initialized before the
|usbport trigger was loaded.

<https://marc.info/?l=linux-usb&m=154577101631079>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
ef5ff08662 ipq40xx: convert to device-tree based USB LED trigger
Thanks to the ledtrig-usb.c the USB LED trigger can be
setup in the device-tree definition for the Asus RT-AC58U
and ZyXEL NBG6617.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
ee5d3a6d7c ipq40xx: fix warning triggered by bad interrupt definition
This patch fixes a kernel warning that got triggered by 4.19
because of a bad/missing interrupt level definition in the DTS.

| WARNING: CPU: 2 PID: 1996 at drivers/irqchip/irq-gic.c:1016
| CPU: 2 PID: 1996 Comm: kmodloader Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| [<c0317884>] (warn_slowpath_null) from [<c04f9cd0>]
| [<c04f9cd0>] (gic_irq_domain_translate) from [<c035af30>]
| [<c035af30>] (irq_create_fwspec_mapping) from [<c035b1e0>]
| [<c035b1e0>] (irq_create_of_mapping) from [<c0614eec>]
| [<c0614eec>] (of_irq_get) from [<c0614f3c>]
| [<c0614f3c>] (of_irq_to_resource) from [<c0614ff0>]
| [<c0614ff0>] (of_irq_to_resource_table) from [<c0610e08>]
| [<c0610e08>] (of_device_alloc) from [<c0610ea0>]
| [<c0610ea0>] (of_platform_device_create_pdata)
| [<c061120c>] (of_platform_bus_create)
| [<c06113c4>] (of_platform_populate)
| [<bf4c06b4>] (dwc3_qcom_probe [dwc3_qcom])

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
6e58fb2c33 ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom
Robert Marko <robimarko@gmail.com> noted in
"ipq40xx: Use kmod-usb-dwc3-qcom by default":
| Since 4.18 we cant use DWC3 OF Simple anymore so we
| have to use kmod-usb-dwc3-qcom.

This patch adds a TODO right next to the KERNEL_PATCHVER so
it will be picked up when moving to 4.19.

I would also like to point out:

All users/devs that are compiling their own images from source
and have a existing 4.14 config and want to switch to 4.19:

Please drop kmod-usb-dwc3-of-simple and add kmod-usb-dwc3-qcom
module package. Otherwise, the USB port on your router will no
longer work.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
a5ac9030ed ipq40xx: MR33: device-tree update
- 4.19 no longer refuses to initialize the mdio bus if
   a phy is not connected.

 - fix partition unit-address

 - restrict partition offset and size to 32-bit integers.

 - add note to warn people not to mess with the ubi
   partition size.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
51ec6bddd3 ipq40xx/ipq806x: 4.19: fix qcom-nandc panic on boot
This patch fixes the crash that occures on rawnand device.
<https://patchwork.ozlabs.org/patch/1017933/>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:35:34 +01:00
Christian Lamparter
a2501ebfb0 ipq40xx: remove qcom,ipq4019 on all devices
Upstream commit:
80483c3abf8 ("ARM: qcom: Cleanup/Remove unnecessary board file")
removed all the platform device compatibles stating that:
"This patch removes the unnecessary board file. The generic machine
definition is sufficient for the Qualcomm platforms."

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:30:45 +01:00
Christian Lamparter
00dd84ca2e ipq40xx: rt-ac58u: fix device-tree snafu
- make the device userspace integration (WIFI,MAC,sysupgrade)
   work again by renaming the ubi to UBI_DEV as a temporary measure.
   In the future, once 4.14 support is dropped, this can all be
   refactored again. *sigh*

 - use the wifi0 and wifi1 labels

 - follow Device-Tree Release v0.2 2.2.2 Generic Names Recommendation

 - fix duplicated partition node-names

 - remove qcom,ipq4019 platform compatible. it's no longer needed
   (and wrong because the chip is a qcom,ipq4018).

Fixes: 4c67f3ad78d ("ipq40xx: Adapt 4.19 DTS for upstream SPI-NAND driver")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:30:45 +01:00
Robert Marko
077a63db1d ipq40xx: 4.19: Enable pseudo random number generator
IPQ40xx series has a HW pseudo random number generator built in.
It already has a node in the upstream ipq4019.dtsi so we just need to enable it.
Its driver has been rewritten to use crypto API so we dont have char interface like under 4.14 kernel.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:30:45 +01:00
Robert Marko
59485f7486 ipq40xx: files-4.19: Clear some DTC warnings
DTC was throwing warnings like this:
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/m25p80@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/spi-nand@1: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

So lets fix this for our downstream boards.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:30:45 +01:00
Robert Marko
c29c8838a1 ipq40xx: Use upstream SPI-NAND driver instead of MT29F
Since 4.19 upstream kernel provides generic SPI-NAND
framework and vendor specific drivers.
Since only users of MT29F are 2 boards with Winbond
W25N01GV SPI-NAND for which support has been backported
from 4.20 we can drop the ever stuck in staging MT29F
driver and instead use the upstream driver.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [squashed]
2018-12-27 14:26:07 +01:00
Robert Marko
13321fa142 ipq40xx: Use kmod-usb-dwc3-qcom by default
Since 4.18 we cant use DWC3 OF Simple anymore so we have to use
kmod-usb-dwc3-qcom.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:06:38 +01:00
Robert Marko
30f2b22952 ipq40xx: Add 4.19 kernel config
This adds the neccessary 4.19 kernel config.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:06:38 +01:00
Robert Marko
8b7abea2f6 ipq40xx: Add patches for 4.19
This adds the necessary patches for 4.19 kernel.
Upstreamed patches were dropped, backported upstreamed patches
from 4.20.
Drop Winbond ID patch since that NAND IC was upstreamed to use
SPI-NAND framework and support for it was backported from 4.20.
Rework ESSEDMA patches to compile under 4.19 due to timer changes,
Clément Péron did the hard work and his changes were taken from the
initial 4.19 PR.
MR33 changes had to be manually refreshed to apply.
Refresh other patches to apply.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove
2018-12-27 14:06:38 +01:00
Robert Marko
96b69c2e9a ipq40xx: Add files for 4.19
This copies over files from 4.14

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:06:38 +01:00
David Bauer
e67da34431 ath79: add support for devolo WiFi pro 1750c
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

There is also a Micro-B USB-port present but this only seems to be a
dummy as the circuit next to it is not present (at least in my unit).

It is also not mentioned in the devolo manual.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
David Bauer
1724d4e9ed ath79: add support for devolo WiFi pro 1200e
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
       1x Atheros AR8033
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN:   1x Reset
LED:   1x LED blue
       1x LED red
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to reset-button

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-27 14:06:38 +01:00
TOCK Chiu
8471944325 ath79: add support for TP-Link Archer C7 v5
This commit adds support for TP-Link Archer C7 v5, leveraging most effort
from commit ea9baee and 1e4ee63. Archer C7 v5 is identical to Archer A7 v5
but with a different flash layout.

Specification:
-   QCA9563 SoC (750 MHz)
-   128 MiB of RAM (DDR2)
-   16 MiB of flash (SPI)
-   5x 1 Gbps Ethernet (1x WAN + 4x LAN)
-   2.4GHz (bgn) SoC internal + 5GHz (ac) QCA9880
-   10x LED, 2x button
-   UART header on PCB

Flash instructions:
1.  Upload openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-factory.bin
    via web interface.

Flash instructions using TFTP recovery:
1.  Plug PC to one of the LAN ports
2.  Set PC to fixed IP address 192.168.0.66
3.  Rename the factory image to ArcherC7v5_tp_recovery.bin and place it in
    TFTP root directory
4.  Turn on the router with the reset button pressed for about 15 secs
5.  Release the button and wait about 150 secs to complete flashing

Signed-off-by: TOCK Chiu <tock.chiu@gmail.com>
2018-12-27 14:06:38 +01:00
Daniel F. Dickinson
3bb44f4299 brcm2708: Add feature flag rootfs-part
Even with squashfs brcm2708 requires ROOTFS_PART_SIZE because the overlay
exists as a loopback device on the space not used by squashfs in the root
partition. Also for ext4 (the other fs option) ROOTFS_PART_SIZE is required,
so use feature flag rootfs-part to enable it.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-12-27 14:06:38 +01:00
Christian Lamparter
1155793809 apm821xx: sata: set rootfs-part feature flag
The rootfs-part feature flag ensures that
CONFIG_ROOTFS_PART_SIZE symbol will be present
at all times.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:06:38 +01:00
Rafał Miłecki
f3006059eb bcm53xx: update 4.19 config
There were 3 new symbols possible to choose: ARCH_BCM_HR2, PCI_V3_SEMI
and PHY_BCM_SR_PCIE.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-27 08:15:08 +01:00
Rafał Miłecki
75b134c4c5 bcm53xx: add support for the kernel 4.19
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-27 07:59:03 +01:00
Rafał Miłecki
7a7d19abcf bcm53xx: backport DTS changes queued for the 4.21
It just replaces some downstream patches & adds relicensing work.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-27 07:33:24 +01:00
Rafał Miłecki
a5d6f2eb76 bcm53xx: rename dts backport patches changing their prefixes
Start 03x with 030 instead of 035. It's a trivial change that adds more
place for further backports in the 03x space.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-27 07:03:30 +01:00
Hauke Mehrtens
e790227553 kernel: Fix KERNEL_STACKPROTECTOR on kernel 4.19
The configuration option was renamed with kernel 4.19 from
CONFIG_CC_STACKPROTECTOR to CONFIG_STACKPROTECTOR adapt the code to set
both options.

CONFIG_STACKPROTECTOR now sets the regular stack protector and
CONFIG_STACKPROTECTOR_STRONG activates the additional protection of more
functions.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-26 17:32:48 +01:00
Hauke Mehrtens
b1daead066 kernel: Add compiler options to generic configuration
With kernel 4.19 new configuration options for the compiler were added.
These are automatically selected and set, instead of having them in each
target configuration, put them into the generic configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-26 17:32:48 +01:00
Hauke Mehrtens
89f8a8be7f kernel: Deactivate CONFIG_COMPAT_BRK
CONFIG_COMPAT_BRK disables the heap randomization which is only needed
for very old and ancient user space applications, I am not aware that we
run any of these, just deactivate this option for these targets to allow
heap randomization.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-26 17:32:48 +01:00
Rafał Miłecki
a28f6ab27f bcm53xx: update pinctrl driver & use its new DT binding
Driver has been updated upstream to support more precise DT binding and
avoid mapping conflicts between pinctrl and USB 2.0 PHY.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-25 15:52:37 +01:00
Kevin Darbyshire-Bryant
8f4841462c kernel: MIPS: math-emu Write-protect delay slot emulation pages
Backport https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=adcc81f148d733b7e8e641300c5590a2cdc13bf3

"Mapping the delay slot emulation page as both writeable & executable
presents a security risk, in that if an exploit can write to & jump into
the page then it can be used as an easy way to execute arbitrary code.

Prevent this by mapping the page read-only for userland, and using
access_process_vm() with the FOLL_FORCE flag to write to it from
mips_dsemul().

This will likely be less efficient due to copy_to_user_page() performing
cache maintenance on a whole page, rather than a single line as in the
previous use of flush_cache_sigtramp(). However this delay slot
emulation code ought not to be running in any performance critical paths
anyway so this isn't really a problem, and we can probably do better in
copy_to_user_page() anyway in future.

A major advantage of this approach is that the fix is small & simple to
backport to stable kernels.

Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 432c6bacbd0c ("MIPS: Use per-mm page to execute branch delay slot instructions")"

Without patch:

cat /proc/self/maps
00400000-0047a000 r-xp 00000000 1f:03 1823       /bin/busybox
00489000-0048a000 r-xp 00079000 1f:03 1823       /bin/busybox
0048a000-0048b000 rwxp 0007a000 1f:03 1823       /bin/busybox
77ec8000-77eed000 r-xp 00000000 1f:03 2296       /lib/libgcc_s.so.1
77eed000-77eee000 rwxp 00015000 1f:03 2296       /lib/libgcc_s.so.1
77eee000-77f81000 r-xp 00000000 1f:03 2470       /lib/libc.so
77f90000-77f92000 rwxp 00092000 1f:03 2470       /lib/libc.so
77f92000-77f94000 rwxp 00000000 00:00 0
7f946000-7f967000 rw-p 00000000 00:00 0          [stack]
7fefb000-7fefc000 rwxp 00000000 00:00 0
7ffac000-7ffad000 r--p 00000000 00:00 0          [vvar]
7ffad000-7ffae000 r-xp 00000000 00:00 0          [vdso]

Patch applied:

cat /proc/self/maps
00400000-0047a000 r-xp 00000000 1f:03 1825       /bin/busybox
00489000-0048a000 r-xp 00079000 1f:03 1825       /bin/busybox
0048a000-0048b000 rwxp 0007a000 1f:03 1825       /bin/busybox
77ed0000-77ef5000 r-xp 00000000 1f:03 2298       /lib/libgcc_s.so.1
77ef5000-77ef6000 rwxp 00015000 1f:03 2298       /lib/libgcc_s.so.1
77ef6000-77f89000 r-xp 00000000 1f:03 2474       /lib/libc.so
77f98000-77f9a000 rwxp 00092000 1f:03 2474       /lib/libc.so
77f9a000-77f9c000 rwxp 00000000 00:00 0
7fbed000-7fc0e000 rw-p 00000000 00:00 0          [stack]
7fefb000-7fefc000 r-xp 00000000 00:00 0
7fff6000-7fff7000 r--p 00000000 00:00 0          [vvar]
7fff7000-7fff8000 r-xp 00000000 00:00 0          [vdso]

Note lack of write permission to 7fefb000-7fefc000

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-12-24 21:52:08 +00:00
Christian Lamparter
87c5fd348d ath79: fix pinmux reg size for QCA955x
The range of pinmux reg property "<0x1804002c 0x40>" for QCA955x
SoC does not includes GPIO_FUNCTION register.

Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-24 19:18:07 +01:00
INAGAKI Hiroshi
c566439c9b ath79: add support for NEC Aterm WG800HP
NEC Aterm WG800HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2.4/5 GHz wifi
  - 2.4 GHz: 2T2R (SoC internal)
  - 5 GHz: 1T1R (QCA9887)
- 4x 10/100/1000 Mbps Ethernet
- 8x LEDs, 3x keys (2x buttons, 1x slide-switch)
- UART through-hole on PCB (J2)
  - Vcc, GND, NC, TX, RX from SoC side
  - 115200n8

Flash instruction using factory image:

1. Connect the computer to the LAN port on WG800HP
2. Connect power cable to WG800HP and turn on it
3. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-24 19:18:07 +01:00
INAGAKI Hiroshi
99df98442e build: move xor-image into image-commands
I moved xor-image into image-commands.mk to use it in ath79 target.

It required for NEC WG800HP.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-24 19:18:07 +01:00
INAGAKI Hiroshi
10a54e1442 ath79: fix pinmux reg value for QCA956x
The range of pinmux reg property "<0x1804002c 0x40>" for QCA956x SoC
does not includes GPIO_FUNCTION register.

If the device uses "&jtag_disable_pins", this causes the following
errors:

[    1.982937] pinctrl-single 1804002c.pinmux: mux offset out of range: 0x40 (0x40)
[    1.990622] pinctrl-single 1804002c.pinmux: could not add functions for pinmux_jtag_disable_pins 64x

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-24 19:18:07 +01:00
Christian Lamparter
212f2a63eb kernel: Add missing symbols to 4.19
Tested with apm82181 and ipq40xx minimal image versions.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-24 19:14:21 +01:00
Kevin Darbyshire-Bryant
5b3afca757 kernel: bump 4.14 to 4.14.90
Refresh all patches

Remove upstream patch:
backport-4.14/424-v4.20-net-dsa-fix-88e6060-roaming.patch

Minor tweak to generic/hack-4.14/902-debloat_proc.patch to cleanly apply
after upstream changes.

Tested-on: ath79

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-12-24 15:06:33 +00:00
Christian Lamparter
360efb1ead ipq40xx: NBG6617: add usb-ledtrig-usbport to DEVICE_PACKAGES
The ZyXEL NBG6617 USB LED was not working with the default images.
It turned out that kmod-usb-ledtrig-usbport was missing from the
default installation.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-22 15:08:24 +01:00
Christian Lamparter
36c19c9f0b apm821xx: switch MX60(W)'s recovery images to multi-image method
In the past, the MX60(W)'s recovery images always had problems
with the size restriction and never really worked without manual
intervention. But starting with 4.19, the MX60(W)'s kernel image
outgrew the allocated space for sysupgrade images as well. Hence
This patch reworks the initramfs, which allows the device to ease
up on the impossible tight kernel size requirements for the
sysupgrade creation and packaging. And as a result, the now
orphaned special ramdisk setup is removed in the process.

This new initramfs can be loaded through the MX60(W) U-boot
in the following way:

=> setenv bootargs console=ttyS0,$baudrate
=> tftpboot $meraki_loadaddr meraki_mx60-initramfs-kernel.bin
   [...]
   Load address: 0x800000
    Loading: ################################################ [...]
    done
   [...]

=> bootm $fileaddr
   \## Booting kernel from Legacy Image at 00800000 ...
    ...

Updated Flashing instructions for new installations which integrates
the new recovery method. Users of existing installations that only
want to sysupgrade don't need to update their existing u-boot env.

=> setenv owrt_load1 ubi read \${meraki_loadaddr} kernel
=> setenv owrt_load2 ubi read \${meraki_loadaddr} recovery
=> setenv lede_bootkernel bootm \${meraki_loadaddr_kernel} - \${meraki_loadaddr_fdt}
=> setenv owrt_bootkernel bootm \${meraki_loadaddr}
=> setenv owrt_bootargs setenv bootargs console=ttyS0,\${baudrate} rootfstype=squashfs mtdoops.mtddev=oops
=> setenv owrt_boot run meraki_ubi owrt_bootargs\; run owrt_load1 meraki_checkpart lede_bootkernel\; run owrt_load2 owrt_bootkernel
=> setenv bootcmd run owrt_boot
=> saveenv

For more information and the latest flashing guide:
please visit the OpenWrt Wiki Page for the MR60:
<https://openwrt.org/toh/meraki/mx60#flashing>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-22 15:08:24 +01:00
David Bauer
b53111ad42 ipq40xx: disable kernel-padding for DNI image
This commit removes the fixed kernel size-padding for the Netgear
DNI image creation as it is not necessary for a working image.

The fake rootfs still needs to be padded to the blocksize.

Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-20 23:54:24 +01:00
Christian Lamparter
6dff341106 ipq40xx: fix pcie wifi unit-address of the MR33 and A62
The unit address should be wifi@1,0 since the device is located
at 0000:01:00.0.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-20 19:21:42 +01:00
Daniel F. Dickinson
99c81eab78 ar71xx: Fix PowerCloud CR5000 5GHz wifi mac
Without this patch PowerCloud CR5000 AR9382 PCIe 5GHz Wifi uses
the mac address from eeprom instead the one specified when
initializing the PCIe chip.  There were two issues:

1) ap94_pci_init on the second PCIe wmac is wrong as there is only one
PCIe wmac on this device (the other wmac is the AR1022/AR9342 SoC wmac).
2) Without specifying pdata->use_eeprom there is a failure to load
firmware and caldata.

Thanks to Christian Lamparter (@chunkeey) for the heavy lifting and
help. [0]

[0] <https://github.com/openwrt/openwrt/pull/1613>

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-12-20 18:28:59 +01:00
Kevin Darbyshire-Bryant
8ff0dd57bf kernel: drop MIPS fix cache flushing for highmem pages
This patch, in a variety of forms, has been around since beginning 2016
as e756c2bb07, ending up in present form 0aa6c7df60 (kernel 4.4.13 bump)
and carried forward ever since.

There have been a number of MIPS kernel memory handling changes since,
including VDSO fixes that meant openwrt patches have been dropped with
no apparent fallout.

Simple tests (ntfs-3g) on a HIGHMEM 512MB mt7621 device have not turned
up data corruption issues which would otherwise be expected.  Similarly
running on other MIPS based devices for the past 2 months hasn't turned
up anything obvious to retain this out of tree patch.

With thanks to Rosen Penev for testing on the known 'highmem' device and
Felix Fietkau for testing advice.  Not putting acked-by as it's my fault
if it breaks :-)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-12-20 09:45:19 +00:00
Stijn Tintel
8c6662a1ac brcm2708: switch to kernel 4.14
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:22 +02:00
Stijn Tintel
f5919b65d4 brcm2708: add kernel 4.14 support
Patch generation process:
- rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable
- git format-patch v4.14.89

Patches skipped during rebase:
- lan78xx: Read MAC address from DT if present
- lan78xx: Enable LEDs and auto-negotiation
- Revert "softirq: Let ksoftirqd do its job"
- sc16is7xx: Fix for multi-channel stall
- lan78xx: Ignore DT MAC address if already valid
- lan78xx: Simple patch to prevent some crashes
- tcp_write_queue_purge clears all the SKBs in the write queue
- Revert "lan78xx: Simple patch to prevent some crashes"
- lan78xx: Connect phy early
- Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro
- Revert "Revert "softirq: Let ksoftirqd do its job""
- ASoC: cs4265: SOC_SINGLE register value error fix
- Revert "ASoC: cs4265: SOC_SINGLE register value error fix"
- Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"
- Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends""

Patches dropped after rebase:
- net: Add non-mainline source for rtl8192cu wlan
- net: Fix rtl8192cu build errors on other platforms
- brcm: adds support for BCM43341 wifi
- brcmfmac: Mute expected startup 'errors'
- ARM64: Fix build break for RTL8187/RTL8192CU wifi
- ARM64: Enable RTL8187/RTL8192CU wifi in build config
- This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator
- brcmfmac: add CLM download support
- brcmfmac: request_firmware_direct is quieter
- Sets the BCDC priority to constant 0
- brcmfmac: Disable ARP offloading when promiscuous
- brcmfmac: Avoid possible out-of-bounds read
- brcmfmac: Delete redundant length check
- net: rtl8192cu: Normalize indentation
- net: rtl8192cu: Fix implicit fallthrough warnings
- Revert "Sets the BCDC priority to constant 0"
- media: cxd2880: Bump to match 4.18.y version
- media: cxd2880-spi: Bump to match 4.18.y version
- Revert "mm: alloc_contig: re-allow CMA to compact FS pages"
- Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages""
- cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with
  MEDIA_SUBDRV_AUTOSELECT
- 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch
- 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch

Make I2C built-in instead of modular as in upstream defconfig; also the
easiest way to get MFD_ARIZONA enabled, which is required by
kmod-sound-soc-rpi-cirrus.
Add missing compatible strings from
4.9/960-add-rasbperrypi-compatible.patch, using upstream names for
compute modules.
Add extra patch to enable the LEDs on lan78xx.

Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y)
Runtime-tested: bcm2708, bcm2710

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
822b4c3b25 brcm2708: add kmod-sound-soc-3dlab-nano-player
Add kernel module for 3Dlab Nano Player support in kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
6971af4ff8 brcm2708: add kmod-sound-soc-rpi-cirrus
Add kernel module for Cirrus Logic Audio Card support in kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
8848694114 brcm2708: add kmod-sound-soc-googlevoicehat
Add kernel module for Google Voice HAT support in kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
6fc4d3350a brcm2708: add kmod-sound-soc-audioinjector-octo-soundcard
Add kernel module for AudioInjector Octo surround sound card support in
kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
7143bab519 brcm2708: add kmod-sound-soc-allo-katana-codec
Add kernel module for Allo Katana DAC support in kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
9fd92c1bc2 brcm2708: add kmod-sound-soc-allo-piano-dac-plus
Add kernel module for the Allo Piano DAC Plus in kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
88397f614a brcm2708: add kmod-sound-soc-allo-digione
Add kernel module for Allo DigiOne support in kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
51ea0f508d brcm2708: add kmod-sound-soc-allo-boss-dac
Add kernel module for Allo Boss DAC support in kernel 4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
a51db53792 brcm2708: add kmod-hwmon-rpi-poe-fan
Add kernel module for the fan on the PoE HAT for the 3B+ model in kernel
4.14. Without this, the fan will not turn on.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
8e52243c77 brcm2708: prepare kmod-drm-vc4 for 4.14
It requires sound card support in the new kernel. HDMI CEC support is
disabled for now; enabling it turned out to be non-trivial.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
2c324e15f8 brcm2708: prepare kmod-video-bcm2835 for 4.14
Since kernel 4.12, this driver appeared in staging. The rpi-4.14.y
kernel tree uses these as well.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
1d6b080dc3 brcm2708: prepare kmod-sound-raspidac3 for 4.14
Support for RaspiDac3 has been removed from the rpi-4.14.y kernel tree.
Make the kmod package depend on kernel 4.9.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:21 +02:00
Stijn Tintel
757fa0b7d3 brcm2708: prepare kmod-sound-arm-bcm2835 for 4.14
Since kernel 4.12, this driver appeared in staging. The rpi-4.14.y
kernel tree uses these as well.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 23:19:20 +02:00
Yangbo Lu
583af20b8b layerscape: use MKUBIFS_OPTS for per-device ubi parameters
UBIFS_OPTS couldn't be used for per-device ubi parameters.
Let's use MKUBIFS_OPTS instead.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-12-18 20:17:23 +01:00
Biwen Li
68904cb8fd layerscape: drop kernel 4.9 support
This patch is to drop kernel 4.9 support.

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2018-12-18 20:17:23 +01:00
Biwen Li
328530c6e7 layerscape: add LS1021AIOT board support
The LS1021A-IoT gateway reference design based on the
QorIQ LS1021A processor is a purpose-built, small
footprint hardware platform with a wide array of
high-speed connectivity and low-speed serial interfaces
to support secure delivery of IoT services for home,
business or other commercial location.

- Combines standards-based, open source software with a
  feature-rich IoT gateway design to establish a common,
  open framework for secured IoT service delivery and
  management.

- Provides a wide assortment of high-speed and serial-based
  connectivity in a compact, highly secure design.

- High efficiency through the use of the Arm-based QorIQ
  LS1021A embedded processor.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
2018-12-18 20:17:23 +01:00
Biwen Li
0a827ebd2f layerscape: upgrade kernel to 4.14
This patch is to upgrade kernel to 4.14 for layerscape.
patches-4.14 for layerscape included two categories.

- NXP Layerscape SDK kernel-4.14 patches

  All patches on tag LSDK-18.09-V4.14 were ported to OpenWrt
  kernel. Since there were hundreds patches, we had to make
  an all-in-one patch for each IP/feature.
  See below links for LSDK kernel.
  https://lsdk.github.io/components.html
  https://source.codeaurora.org/external/qoriq/qoriq-components/linux

- Non-LSDK kernel patches

  Other patches which were not in LSDK were just put in patches-4.14.
  Kept below patches from patches-4.9.
  303-dts-layerscape-add-traverse-ls1043.patch
  821-add-esdhc-vsel-to-ls1043.patch
  822-rgmii-fixed-link.patch

  Renamed and rebase them as below in patches-4.14,
  303-add-DTS-for-Traverse-LS1043-Boards.patch
  712-sdk-dpaa-rgmii-fixed-link.patch
  824-mmc-sdhci-of-esdhc-add-voltage-switch-support-for-ls.patch

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
2018-12-18 20:17:23 +01:00
Petr Štetiar
7bd6969acc kernel: Add missing symbols to 4.19
While building 4.19 for ath79 with CONFIG_ALL_KMODS=y with verbose mode
enabled I was asked by kernel config about few symbols/modules so I'm
adding those missing symbols to the generic config.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-18 20:17:22 +01:00
Koen Vandeputte
6835c13e5a cns3xxx: fix writing to wrong PCI registers
Originally, cns3xxx used it's own functions for mapping, reading and writing registers.

Upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
removed the internal PCI config write function in favor of the generic one:

cns3xxx_pci_write_config() --> pci_generic_config_write()

cns3xxx_pci_write_config() expected aligned addresses, being produced by cns3xxx_pci_map_bus()
while the generic one pci_generic_config_write() actually expects the real address
as both the function and hardware are capable of byte-aligned writes.

This currently leads to pci_generic_config_write() writing
to the wrong registers on some ocasions.

First issue seen due to this:

- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER, located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C (CACHE_LINE_SIZE)

This seems to cause some slight instability when certain PCI devices are used.

Another issue example caused by this this is the PCI bus numbering,
where the primary bus is higher than the secondary, which is impossible.

Before:

00:00.0 PCI bridge: Cavium, Inc. Device 3400 (rev 01) (prog-if 00 [Normal decode])
    Flags: bus master, fast devsel, latency 0, IRQ 255
    Bus: primary=02, secondary=01, subordinate=ff, sec-latency=0

After fix:

00:00.0 PCI bridge: Cavium, Inc. Device 3400 (rev 01) (prog-if 00 [Normal decode])
    Flags: bus master, fast devsel, latency 0, IRQ 255
    Bus: primary=00, secondary=01, subordinate=02, sec-latency=0

And very likely some more ..

Fix all by omitting the alignment being done in the mapping function.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-18 14:24:57 +01:00
Koen Vandeputte
9f2739e924 kernel: bump 4.14 to 4.14.89
Refreshed all patches.

Remove upstreamed patches:
- 096-v4.20-netfilter-ipv6-Preserve-link-scope-traffic-original-.patch

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-18 14:24:57 +01:00
Koen Vandeputte
dd0a213bed kernel: bump 4.9 to 4.9.146
Refreshed all patches.

Compile-tested on: brcm2708
Runtime-tested on: brcm2708

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-18 14:24:57 +01:00
Koen Vandeputte
902a9f23d6 kernel: bump 3.18 to 3.18.130
Refreshed all patches.

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-18 14:24:57 +01:00
Mathias Kresin
38cae44e51 ath79: replace cameo-factory with existing build commands
Use pad-offset and append-string to create the cameo factory images for
the D-LINK DIR-825 C1/DIR-835 A1 factory images.

Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-17 23:21:40 +01:00
Mathias Kresin
ffdce856e0 build: move append-string to image-commands.mk
Move it to image-commands.mk so that it can used by other targets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-17 23:21:26 +01:00
Hans Dedecker
b0414d7188 kernel: preserve oif of IPv6 link scope packets
Backort upstream patch which preserves oif of IPv6 link scoped packets.
The outgoing interface of IPv6 link scope packets can be changed by the
function ip6_route_me_harder. This is unwanted behavior for link local
packets and multicast packets as the outgoing interface is fixed and must
not be altered as it can break neighbor discovery and multicast listener
discovery.

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2018-12-17 21:42:23 +01:00
Christian Lamparter
5ae45dc7b3 ipq40xx: GL-B1300: convert to new partitions layout
Alberto Bursi reported:
>The patch "ipq40xx: specify "firmware" partition format for GL.iNet GL-B1300"
>prevents boot on my B1300. I compiled from latest sources.

The GL-B1300 was using the discouraged direct subnodes method to declare
the partitions on the flash.

|The partition table should be a subnode of the flash node and should be named
|'partitions'. This node should have the following property:
|- compatible : (required) must be "fixed-partitions"
|Partitions are then defined in subnodes of the partitions node.
|
|For backwards compatibility partitions as direct subnodes of the flash device are
|supported. This use is discouraged.
|NOTE: also for backwards compatibility, direct subnodes that have a compatible
|string are not considered partitions, as they may be used for other bindings.
<https://www.kernel.org/doc/Documentation/devicetree/bindings/mtd/partition.txt>

Hence, this patch converts the device to the "partitions" layout.

Fixes: 1cbe457cf9 ("ipq40xx: specify "firmware" partition format for GL.iNet GL-B1300")
Reported-by: Alberto Bursi <bobafetthotmail@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 14:22:28 +01:00
Christian Lamparter
b9501cecde ath79: dts: Remove newly added default-state=off property
I'm afraid that this will be "one of many" patches to come.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 14:22:28 +01:00
Christian Lamparter
f54ac91ef5 ar71xx/ath79: switch devices to the -ct driver and firmware
Since commit 61b5b4971e ("mac80211: make ath10k-ct the default ath10k")
select ath10k-ct and the -ct firmwares by default.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 14:22:28 +01:00
Rafał Miłecki
4472df23da bcm53xx: include WiFi firmware for devices with 4366C0
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-17 12:51:06 +01:00
Kevin Darbyshire-Bryant
2574c86ce6 kernel: backport ifconfig ioctl support for class e addresses
Backport net: Allow class-e address assignment via ifconfig ioctl
While most distributions long ago switched to the iproute2 suite
of utilities, which allow class-e (240.0.0.0/4) address assignment,
distributions relying on busybox, toybox and other forms of
ifconfig cannot assign class-e addresses without this kernel patch.

While CIDR has been obsolete for 2 decades, and a survey of all the
open source code in the world shows the IN_whatever macros are also
obsolete... rather than obsolete CIDR from this ioctl entirely, this
patch merely enables class-e assignment, sanely.

https://git.kernel.org/pub/scm/linux/kernel/git/davem/net.git/commit/?id=65cab850f0eeaa9180bd2e10a231964f33743edf

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-12-17 10:40:20 +00:00
Petr Štetiar
0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00
Karl-Felix Glatzer
1e4ee63cc8 ath79: add support for TP-Link Archer A7
This patch adds support for TP-Link Archer A7

Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
  - 2.4GHz (bgn) SoC internal
  - 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
  - Vcc, GND, RX, TX from ethernet port side
  - 115200n8

Flash instructions:

Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.

Flash instruction using tftp recovery:

1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
   root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
   and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing

Changes since first revision:

  - Flash instructions using stock image webinterface
  - Changed "Version 5" in model string to "v5"
  - Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
    and qca9563_tplink_archer-a7-v5.dts
  - Firmware image is now build with dynamic partitioning
  - Default to ath10k-ct

Changes since second revision:
  - Changed uboot@0 to uboot@20000 in DTS file
  - Fixed ordering issue in board led script
  - Specify firmware partition format in DTS file
  - Rebased Makefile device definition on common
    Device/tplink-safeloader-uimage definition
  - Merged switch section in network script
    (same configuration as tplink,tl-wdr3600
    and tplink,tl-wdr4300)

Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
2018-12-17 08:09:13 +01:00
Petr Štetiar
d9753f0ec5 ath79, brcm63xx: Fix debounce-interval properties in gpio-keys-polled nodes
This patch fixes wrong usage of debounce-interval subnode property of
gpio-keys-polled nodes, which was used inproperly in parent node, but it
belongs to the subnodes, excerpt from the docs:

 Optional subnode-properties:
     - debounce-interval: Debouncing interval time in milliseconds.
       If not specified defaults to 5.

And the docs are up to date as the source code matches that description
as well:

 if (fwnode_property_read_u32(child, "debounce-interval",
                              &button->debounce_interval))
         button->debounce_interval = 5;

While at it, I've also re-formatted gpio-keys-polled nodes, usually just
adding new lines after every key subnode.

Cc: Tomasz Maciej Nowak <tomek_n@o2.pl>
Cc: Matt Merhar <mattmerhar@protonmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:05:03 +01:00
Petr Štetiar
7bd2595b67 ath79: ag71xx: Fix code formatting in ag71xx_probe
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:04:19 +01:00
Petr Štetiar
a29df78c9f ath79: ag71xx: Unify debug output with ar71xx and make debugging easier
Currently it's quite hard to diff debugging output between ar71xx and
ath79, so this patch tries to improve it by adding the same
ag71xx_dump_regs function and placing debugging output from the
registers to relatively same places.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:04:05 +01:00
Petr Štetiar
22f9afa118 ar71xx: ag71xx: Replace duplicate debugging code with simple function call
ag71xx_dump_regs is used in code several times, and is providing same
output.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:03:45 +01:00
Stefan Lippers-Hollmann
6b63595fec ipq806x: drop kernel/ rootfs partition images for the ZyXEL NBG6817
Since commit 8e9a59a6b9 (build: add
mkrasimage) a proper factory image can be provided for the ZyXEL
NBG6817, which can be flashed from the OEM firmware or used for
tftp based push-button recovery, therefore the previously used
partition images for mmcblk0p5-rootfs.bin and mmcblk0p4-kernel.bin
are no longer required (and using them properly has always been
slightly difficult and risky) and can now be dropped from the image
generation code.

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
2018-12-17 00:21:34 +01:00
Sebastian Kemper
6c3c4436ee ath79: add d-link dir-825-c1 and dir-835-a1
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.

The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.

https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1
https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1

Installation:

1. Connect to the web interface of the vendor firmware (usually
   listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
   selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.

Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.

Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
2018-12-17 00:21:34 +01:00
Christian Lamparter
2630aae36f ipq40xx: device-tree overhaul
- replace licence texts with SPDX-License-Identifier where
   applicable.

 - make node-names more generic to fit with Device-Tree Release v0.2
   Section 2.2.2 Generic Names Recommendation.

 - utilize wifi0/1, blsp1_uart1 labels

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:34 +01:00
Christian Lamparter
97ba1411e5 ipq40xx: specify "firmware" partition format for EnGenius EAP1300
Specify firmware partition format by compatible string.

Cc: Steven Lin <steven.lin@senao.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:34 +01:00
Christian Lamparter
1cbe457cf9 ipq40xx: specify "firmware" partition format for GL.iNet GL-B1300
Specify firmware partition format by compatible string.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:34 +01:00
Christian Lamparter
771736c039 ipq40xx: specify "firmware" partition format for Compex WPJ428
Specify firmware partition format by compatible string.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:34 +01:00
Christian Lamparter
db2e32c04b ipq40xx: specify "firmware" partition format for ZyXEL WRE6606
Specify firmware partition format by compatible string.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:34 +01:00
Christian Lamparter
e2dc8f2ab4 ipq40xx: specify "firmware" partition format for Netgear EX61[50]0v2
Specify firmware partition format by compatible string.

Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:34 +01:00
Christian Lamparter
bff9d4e081 ipq40xx: specify "firmware" partition format for AVM Fritz!Box 4040
Specify firmware partition format by compatible string.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:34 +01:00
Christian Lamparter
40180b6305 kernel: add DT binding support to the fit parser
It allows specifying default and Netgear parsers directly in the DT.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-17 00:21:33 +01:00
Hauke Mehrtens
3c04d10483 gemini: Activate USB support again
This activates the CONFIG_USB_SUPPORT option in the in the gemini kernel
again which will provide the core USB support and makes it possible to
compile the rest of the USB parts into modules. Without this change USB
will not be available in the gemini target and some modules fail to
compile because the feature list indicates USB support.

Fixes: 10ec966f7b ("gemini: Break out USB to packages")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-16 14:59:59 +01:00
NOGUCHI Hiroshi
83a97c53fa ramips: add support for Netgear R6350
Netgear R6350 is a wireless router, aka Netgear AC1750.

Specification:
- SoC: Mediatek MT7621AT (2 CPU cores, 4 threads)
- RAM: 128MiB (Nanya NT5CC64M16GP-DI)
- ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI)
- Wireless:
   for 11b/g/n (upto 300Mbps): MT7603
   for 11a/ac  (upto 1450Mbps) : MT7615, is not avaliable now
- Ethernet LAN speed: up to 1000Mbps
- Ethernet LAN ports: 4
- Ethernet WAN speed: up to 1000Mbps
- Ethernet WAN ports: 1
- USB ports: 1 (USB 2.0)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 2
- serial ports: unknown

Installation through telnet:
  - Copy kernel.bin and rootfs.bin to a USB flash disk,
    plug to usb port on the router.
  - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
    (login if required, default: admin password)
  - You will see "Debug Enabled!"
  - Telnet 192.168.1.1 and login with "root"
  - ls /mnt/shares/ to find out path of your USB disk.
    'myUdisk' for example.
  - cd /mnt/shares/myUdisk
  - mtd_write write rootfs.bin Rootfs
  - mtd_write write kernel.bin Kernel
  - reboot

recovery when bricked:
  nmrpflash can be used to recover to the netgear firmware
  if a broken image was flashed.

The SC_PART_MAP partition suggests that an on flash partition table
exists. After implementing a partition parser/builder for the sercom
partition format, the definitions don't match the flash layout used by
the stock firmware.

It either means the partition format has not yet been completely
understood or it isn't used by the stock firmware. For now, use fixed
partitions instead.

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[apply latest ramips changes and document the on flash partition map
issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-16 08:41:41 +01:00
Daniel Santos
9850e42284 jffs2: Fix use of uninitialized delayed_work, lockdep breakage
I've sent this one upstream.  This patch is critical if you want to run
with "prove lock correctness" (lockdep) and you happen to have certain
mtd devices.  The misuse of the uninitialized object is undefined
behaviour, but being zeroed it does not appear to have actually broken
anything other than the lockdep engine.

Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
2018-12-16 01:18:48 +01:00
Brett Mastbergen
2b6eab507a netfilter: Add fib support for nftables
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
2018-12-16 00:57:20 +01:00
Anderson Luiz Alves
0c3c944d1e kernel: mv88e6060: disable hardware level MAC learning
Disable Marvell's hardware level MAC learning because it breaks station roaming.

When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.

Problem description:
Multiple APs with inter-AP roaming connected to different ports,
when station moves from one AP on one port to another AP on another port,
traffic flow breaks down because the learning table is not updated.

Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
[Replaced with upstream version, move to generic]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-16 00:57:20 +01:00
Deng Qingfang
18501889f6 kernel: add mv88e61xx switch port-mirroring support
Compile & run tested on mvebu

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-16 00:57:20 +01:00
Andre Heider
5d501e54fc lantiq: add integer latency stat for lantiq-dsl
The current stats always have a 'ms' suffix, and they're used by luci.
Introduce dsl.latency_[down|up] values, exported in µs without suffix.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2018-12-16 00:57:19 +01:00
Marcin Jurkowski
3c3eaa57d9 ath79: add support for TP-Link TL-WR842N/ND v1 router
This ports support for TP-Link TL-WR842N/ND v1 from ar71xx.

CPU: Atheros AR7241 400 MHz
RAM: 32 MiB
FLASH: 8 MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9287
LED: SYS, WiFi, LAN, WAN, 3G, QSS
BTN: WiFi, Reset/WPS

AR71xx target used "tl-mr3420" as board id so force flag is needed
if upgrading from old target.

Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial cleanup]
2018-12-15 21:35:45 +01:00
Christian Lamparter
330965b342 ipq806x: add ath10k calibration data MAC addresses patching
Ben Greear reported in his patch:
|Subject: netgear r7800: Fix mac address of radios.
|
|Reloading the driver causes the phyX to change, and that
|caused the MAC address to change.

This is because all ODM/OEMs except QCA bothered to write
the correct MAC address for the ath10k wifi into the
calibration data.

This patch copies over the MAC patching helper functions from ipq40xx's
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
file and converts all the devices to patch the correct MACs into the
extracted calibration data before it gets sent to the driver, which sets
up the device with the correct MAC address. It also removes the entries
in the 10_fix_wifi_mac file as they have served their purpose for good.

Please note the C2600: There is conflicting information on what
the offset for the second wifi is supposed to be. This patch uses
what was specified in 10_fix_wifi_mac.

According to Ben Greear this method is save to use with the
stock firmware too. As he explained that the stock firmware
messes up rx-bssid mask calculation when the MAC is changed
after the first vif is created.

Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-15 21:06:11 +01:00
Mathias Kresin
dd5e7d6c50 ramips: mt7620: add usb packages
Add the usb drivers for all boards with enabled ochi/ehci node in the
dts file.

Fixes: FS#1987

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Mathias Kresin
30c07a5675 ramips: mt7620: remove unnecessary usb packages
These are either installed as dependency or not required at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Mathias Kresin
e04d352d63 ramips: mt7620: add usb ohci driver
Add the USB 1.1 driver for all boards not having a fixed USB 2.0
device attached to the USB bus.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Deng Qingfang
47381aadd5 ramips: several fixes for HC5x61
- Mark other partitions as read-only for HC5x61

 - Only enable USB and PCIe for HC5761/HC5861
   HC5661 doesn't have a USB port, and there is nothing attached to its PCIe.

 - Fix HC5761 switch ports
   HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports.

 - Fix HC5861 5GHz radio
   HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN.

 - Fix HC5761/HC5861 WiFi LEDs
   After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1.

 - Fix HC5x61 image size
   It should be 15872k (0xf80000)

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-15 20:02:07 +01:00
Christian Lamparter
10ad6d6e07 ipq40xx: integrate ath10kcal_patch_mac into ath10kcal_patch_mac_crc
In the thread: "ipq806x: add ath10k calibration data MAC addresses patching"
Chuanhong Guo <gch981213@gmail.com> noted that:
"All ath10k calibration data have a checksum at 0x2.
ath10kcal_patch_mac works for QCA9880/QCA9882 only because
the ath10k firmware for these two chips doesn't check the
checksum value. (QCA proprietary driver checks this and
refuses to use caldata with incorrect checksum.)"

This patch updates 11-ath10k-caldata of the ipq40xx target accordingly.

Reported-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-15 19:02:00 +01:00
Hauke Mehrtens
fbaf48387e kernel: netfilter: chain filters merged into nf_tables.ko
In mainline kernel commit 02c7b25e5f5 ("netfilter: nf_tables: build-in
filter chain type") all chain filters were merged into one file and into
one kernel module to save some memory. The code protected by these
configuration options CONFIG_NF_TABLES_BRIDGE, CONFIG_NF_TABLES_IPV4,
CONFIG_NF_TABLES_ARP, CONFIG_NF_TABLES_IPV6, CONFIG_NF_TABLES_NETDEV and
CONFIG_NF_TABLES_INET was merged into the nft_chain_filter.c file which
is now always compiled into the nf_tables.ko file.

This only happened in kernel 4.19 and OpenWrt has to select these as
modules in older kennel versions. Mark them as build-in in the kernel
4.19 specific kernel configuration file which will then not be
overwritten by the package specific settings which try to make them
modular again.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 14:28:50 +01:00
Hauke Mehrtens
f891670704 kernel: netfilter: Adapt merge ipv4/ipv6 masquerade code
In kernel commit 0168e8b361 ("netfilter: nat: merge ipv4/ipv6 masquerade
code into main nat module") the CONFIG_NF_NAT_MASQUERADE_IPV4 and
CONFIG_NF_NAT_MASQUERADE_IPV6 kernel configuration option were changed
to bool and the code will not be compiled as a own module any more, but
it will be integrated into nf_nat_ipv4.ko or nf_nat_ipv6.ko to save some
memory.

Activate these options as bool in the generic kernel 4.19 configuration
only, to always build them into the nf_nat_ipv*.ko modules. The kmod
file will still try to select them as module, but the generic
configuration will not be overwritten.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 14:28:50 +01:00
Hauke Mehrtens
d234431c0c kernel: Make CONFIG_NVMEM tristate
CONFIG_OF_NET depends on CONFIG_NVMEM in kernel 4.19. To fix some build
problems in mainline Linux kernel CONFIG_NVMEM was changed from tristate
to bool in commit 2a37ce25d9 ("nvmem: disallow modular CONFIG_NVMEM").

This patch in OpenWrt revert the upstream commit and changes
CONFIG_NVMEM back to tristate we just have to make sure to build this in
for all targets which select CONFIG_OF_NET.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 14:28:50 +01:00
Hauke Mehrtens
edc4da5da1 kernel: Always activate CONFIG_HW_RANDOM_TPM
CONFIG_HW_RANDOM_TPM does not activate a separate kernel module any
more, but it only activates the random code in the tpm.ko.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 14:28:49 +01:00
Hauke Mehrtens
e30ea44f68 kernel: Remove deprecated generic linux,part-probe patch
This is now replaced by some other mtd partition parsing which was
merged into upstream.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 14:28:48 +01:00
Hauke Mehrtens
9261e7447e kernel: Make the patches apply on top of 4.19
This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.

The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.

The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch

Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch

Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.

The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch

I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch

This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 14:28:48 +01:00
Hauke Mehrtens
52a82ce3dd kernel: Copy patches from kernel 4.14 to 4.19
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 12:50:06 +01:00
Hauke Mehrtens
a272af75cd kernel: Move modifications of b53.h into patch
The b53 driver was added as a dsa driver into the mainline Linux kernel,
but we still use the swconfig based driver. The header file b53.h is
used by both drivers, but the swconfig one needs an extra member, add
this one in a patch to not overwrite the version shipped with the
mainline kernel.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 12:50:06 +01:00
Hauke Mehrtens
aa3b6a08c5 kernel: Replace ledtrig-netdev with upstream backport
The ledtrig-netdev was added to upstream Linux kernel 4.16, replace our
own version with the patch based on the upstream version.
This will remove the ledtrig-netdev support from kernel 3.18, because I
not want to spend time on backporting it to 3.18. This will make it
easier to use the upstream version with kernel 4.19, by just not
applying this patch.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 12:50:06 +01:00
Hauke Mehrtens
42e62a8a10 kernel: Reorder configuration
This reorders the generic kernel configuration files.
This was done with the following commands:
$ ./scripts/kconfig.pl '+' target/linux/generic/config-4.14 /dev/null > target/linux/generic/config-4.14-new
$ mv target/linux/generic/config-4.14-new target/linux/generic/config-4.14
$ ./scripts/kconfig.pl '+' target/linux/generic/config-4.9 /dev/null > target/linux/generic/config-4.9-new
$ mv target/linux/generic/config-4.9-new target/linux/generic/config-4.9

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-12-15 12:50:06 +01:00
Koen Vandeputte
fdd11a6eae kernel: bump 4.14 to 4.14.88
Refreshed all patches.

Altered patches:
- 180-usb-xhci-add-support-for-performing-fake-doorbell.patch

Fixes CVE:
- CVE-2018-14625

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-14 13:01:49 +01:00
Koen Vandeputte
fd918b413a kernel: bump 4.9 to 4.9.145
Refreshed all patches.

Fixes CVE:
- CVE-2018-14625

Compile-tested on: brcm2708
Runtime-tested on: brcm2708

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-14 13:01:45 +01:00
Rafał Miłecki
816ae87709 kernel: drop unneeded LINUX_VERSION_CODE checks
All those parsers are used by 4.14 targets. They don't need that
backward compatibility code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-13 16:59:21 +01:00
Rafał Miłecki
2abb128f2e kernel: add DT binding support to the LZMA and WRG parsers
It allows specifying those parsers directly in the DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-13 16:59:00 +01:00
Rafał Miłecki
840c4cba92 ramips: mt7621: disable CONFIG_MTD_SPLIT_FIRMWARE
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-13 13:39:56 +01:00
Rafał Miłecki
c56241c052 ramips: mt7621: specify "firmware" partition format for remaining devices
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-13 13:39:56 +01:00
INAGAKI Hiroshi
3198ec5b9d ipq806x: fix and cleanup dts for NEC WG2600HP
This commit fixes and cleanups qcom-ipq8064-wg2600hp.dts to improve the
support for WG2600HP.

- Use dt label in qcom-ipq8064.dtsi:

  - gmac1
  - gmac2
  - gsbi4
    - gsbi4_serial
  - gsbi5
  - hs_phy_0
  - ss_phy_0
  - usb3_0
  - usb3_1
  - pcie0
  - pcie1
  - qcom_pinmux

- Fix wrong pcie reset (perst) gpios

  - drop reset-gpio and use perst-gpios in qcom-ipq8064.dtsi

- Remove unnecessary dt label from device dts

  - flash
  - phy0, phy4

- Rename spi-nor node to "flash" from "m25p80"

- Fix qca,ar8327-initvals

  - use oem settings

    - fix: PAD0_MODE, PAD6_MODE
    - drop: PAD5_MODE (unnecessary)

- Move mtd partitions under partitions (fixed-partitions) node

- Specify "firmware" partition format

  - WG2600HP uses uImage format (denx,uimage)

- Change failsafe status LED to power_red

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-12-12 18:59:01 +01:00
Mathias Kresin
0fdfdaef2d ath79: fix dtc compiler warnings
The qca9557/qca956x reset-controller aren't a simple bus. A simple bus
would require node unit addresses.

Add the node unit addresses for the qca9557 usb phys. Add the regs for
the USB_PWRCTL and USB_CONFIG registers even not yet used.

Fix the wrong ar7100 pcie controller node unit address as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 12:28:26 +01:00
Mathias Kresin
35f70774b8 ramips: drop old image validation code
Due to the enforced image metadata we ensure that the correct image is
uploaded. Checks based on a magic arn't required any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Mathias Kresin
1a5df6add7 ramips: enforce image metadata verification
Now that we got rid of all legacy images, we can enforce image metadata
verification.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Mathias Kresin
8e40fbff0b ramips: drop support for ALLNET ALL0239-3G and Sitecom WL-341 v3
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.

Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.

The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Mathias Kresin
262b885b83 ramips: use new image build code for D-Link DCS-930 family
Drop the factory images and the firmware tool to create them. They don't
work any more, since the factory image has an uImage header covering the
whole kernel + rootfs. This way the uImage splitter will not be able to
find the rootfs and the kernel will panic later on.

The factory images were most likely added at a time the board had
distinct partitions for kernel and rootfs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Daniel Gonzalez Cabanelas
26d4cb2ca7 brcm63xx: HG655b: fix the imagetag at dts
Fix the imagetag on the HG655b to allow a correct partition detection at boot time.

It turns out that it was defined at the wrong partition. Just move the imagetag to
the linux firmware partition.

The bug is present since the 18.06 release. Without this fix, the board won't boot.

Fixes: a27d59bb42 ("brcm63xx: switch to new partition layout specification")
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-12-11 13:36:52 +01:00
Jonas Gorski
e08ef42b24 brcm63xx: fix ethernet switch core reset mask for BCM6368
The reset mask for the bcm6368 switch core was left at 0 due to a copy &
paste error. Fix this by setting it to the correct value.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-12-11 13:11:51 +01:00
Jonas Gorski
620b36c1b5 brcm63xx: drop legacy profile for SR102
Remove the sky.mk causing a duplicate device profile to be added in
image builder. The generic device code already generates a profile for
the device.

Fixes FS#1780.

Fixes: d591260407 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2018-12-11 13:11:10 +01:00
Koen Vandeputte
ecc6f3ff76 kernel: add missing symbol in some 4.9 subtargets
Buildbot revealed some subtargets are still missing the new symbol.

Fixes: dfbf836a52 ("kernel: bump 4.9 to 4.9.143")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-11 11:34:45 +01:00
Koen Vandeputte
f6e9f23771 kernel: bump 4.14 to 4.14.87
Refreshed all patches.

Remove upstreamed:
- 0008-MIPS-ralink-Fix-mt7620-nd_sd-pinmux.patch

Compile-tested: cns3xxx, imx6
Runtime-tested: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-10 16:32:22 +01:00
Koen Vandeputte
861dcd717f kernel: bump 4.9 to 4.9.144
Refreshed all patches.

Remove upstreamed:
- 014-Kbuild-suppress-packed-not-aligned-warning-for-defau.patch

Compile-tested: ar7, brcm2708
Runtime-tested: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-10 16:32:22 +01:00
Koen Vandeputte
0028f86687 kernel: bump 4.14 to 4.14.86
Refreshed all patches.

Altered patches:
- 180-usb-xhci-add-support-for-performing-fake-doorbell.patch

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-10 11:48:44 +01:00
Koen Vandeputte
dfbf836a52 kernel: bump 4.9 to 4.9.143
Refreshed all patches.

Altered patches:
- 950-0063-Improve-__copy_to_user-and-__copy_from_user-performa.patch
- 201-extra_optimization.patch

New symbol:
- CONFIG_HARDEN_BRANCH_PREDICTOR

Compile-tested on: ar7, at91, brcm2708, ixp4xx, layerscape, orion
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[fix brcm2708/950-0149-Update-vfpmodule.c.patch]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-12-10 11:48:44 +01:00
Koen Vandeputte
4e38fc824c kernel: bump 3.18 to 3.18.128
Refreshed all patches.

Altered patches:
- 002-phy_drivers_backport.patch

Compile-tested on: adm5120
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-12-10 11:48:44 +01:00
Christian Lamparter
0bce89037f apm821xx: WNDAP620: remove bad semicolon in dts after #include
This patch fixes a build warning triggered by a semicolon in
the dts after the #include directive.

netgear-wndap620.dts:11:33: warning: extra tokens at end of #include directive

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-09 15:27:34 +01:00
Christian Lamparter
bd3e234473 apm821xx: move fifo-entry-size property to WNDR4700
This property (and value) came from Netgear's WNDR4700
stock firmware dts. However, other devices do not set
it and the EMAC default is 16, which matches that of
the programming notes of the APM82181 spec.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-09 15:27:29 +01:00
Rafał Miłecki
4d3a53b9ef kernel: add DT binding support to the TRX and minor parsers
It allows specifying those parsers directly in the DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-12-09 13:58:54 +01:00
Russell Senior
ed000fcaf2 ramips: fix firmware compatible string for dir860l-b1
In commit d70ec3008d, a firmware compatible
string of "denx,uimage" was added for the Dlink DIR-860L-B1. Unfortunately,
this was the wrong string. It needs "seama" instead.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-12-08 14:18:42 +01:00
Romain MARIADASSOU
02494fa35c
Add support for TL-WA801ND v4
This add support for TP-Link TL-WA801ND v4 (same as TL-WA801ND v3) :

Specification:

- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: 650 MHz
- Flash-Chip: Winbond W25Q32BVSIG
- Flash size: 4096 KiB
- RAM: 32 MiB
- Wireless No1: SoC-integrated: QCA9533 2.4GHz 802.11bgn

Flash instructions:

1) To flash the image, rename the file
   openwrt-ar71xx-generic-tl-wa801nd-v4-squashfs-factory.bin
   to firmware.bin
2) Connect your device to the LAN port, then upload the firmware
   through web interface. It will try to download the image and
   flash it.

It can take up to 2-3 minutes to finish. When it reaches 100%, the
router will reboot itself.

Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
2018-12-07 21:46:45 +01:00
Daniel F. Dickinson
32bc733796 ath79: dts: Use PowerCloud CAP324 bicolor status LED
PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files /
base files support using both colours to better inform user of state
and to better match stock firmware, so use green power to indicate
normal operation.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
2018-12-06 20:26:57 +01:00