mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 05:38:00 +00:00
ipq806x: add support for Buffalo WXR-2533DHP
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
This commit is contained in:
INAGAKI Hiroshi
Christian Lamparter
parent
7e9b93fb1b
commit
51fe956c4f
@ -11,6 +11,10 @@ board=$(board_name)
|
||||
boardname="${board##*,}"
|
||||
|
||||
case "$board" in
|
||||
buffalo,wxr-2533dhp)
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:white:wireless" "phy0tpt"
|
||||
ucidef_set_led_switch "wan" "WAN" "${boardname}:white:internet" "switch0" "0x20"
|
||||
;;
|
||||
compex,wpq864)
|
||||
ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1"
|
||||
ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1"
|
||||
|
||||
@ -12,6 +12,7 @@ board_config_update
|
||||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
buffalo,wxr-2533dhp |\
|
||||
compex,wpq864 |\
|
||||
netgear,d7800 |\
|
||||
netgear,r7500 |\
|
||||
|
||||
@ -79,6 +79,10 @@ board=$(board_name)
|
||||
case "$FIRMWARE" in
|
||||
"ath10k/pre-cal-pci-0000:01:00.0.bin")
|
||||
case $board in
|
||||
buffalo,wxr-2533dhp)
|
||||
ath10kcal_extract "ART" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 30)
|
||||
;;
|
||||
linksys,ea8500)
|
||||
ath10kcal_extract "art" 4096 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1)
|
||||
@ -109,6 +113,10 @@ case "$FIRMWARE" in
|
||||
;;
|
||||
"ath10k/pre-cal-pci-0001:01:00.0.bin")
|
||||
case $board in
|
||||
buffalo,wxr-2533dhp)
|
||||
ath10kcal_extract "ART" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_binary ART 24)
|
||||
;;
|
||||
linksys,ea8500)
|
||||
ath10kcal_extract "art" 20480 12064
|
||||
ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +2)
|
||||
|
||||
45
target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh
Normal file
45
target/linux/ipq806x/base-files/lib/upgrade/buffalo.sh
Normal file
@ -0,0 +1,45 @@
|
||||
#!/bin/sh
|
||||
# Copyright (C) 2018 OpenWrt.org
|
||||
#
|
||||
|
||||
. /lib/functions.sh
|
||||
|
||||
# The mtd partition 'ubi' and 'rootfs_1' on NAND flash are os-image
|
||||
# partitions. These partitions are called as "Bank1/Bank2" in U-Boot
|
||||
# on WXR-2533DHP, and they are checked conditions when booting.
|
||||
# Then, U-Boot checks kernel and rootfs volumes in ubi, but U-Boot
|
||||
# needs "ubi_rootfs" as rootfs volume name. And, U-Boot checks the
|
||||
# checksum at the end of rootfs (ubi_rootfs).
|
||||
# When U-Boot writes os-image into the Bank, only kernel, rootfs
|
||||
# (ubi_rootfs) and rootfs_data (ubi_rootfs_data) volumes are wrote
|
||||
# into the Bank. (not full ubi image)
|
||||
#
|
||||
# == U-Boot Behaviors ==
|
||||
# - Bank1/Bank2 images are good, images are different
|
||||
# -> writes os-image to Bank1 from Bank2
|
||||
# (this behavior is used to firmware upgrade in stock firmware)
|
||||
# - Bank1 image is broken (or checksum error)
|
||||
# -> writes os-image to Bank1 from Bank2
|
||||
# - Bank2 image is broken (or checksum error)
|
||||
# -> writes os-image to Bank2 from Bank1
|
||||
# - Bank1/Bank2 images are broken (or checksum error)
|
||||
# -> start tftp
|
||||
|
||||
buffalo_upgrade_prepare_ubi() {
|
||||
local ubidev="$( nand_find_ubi ubi )"
|
||||
local mtdnum2="$( find_mtd_index rootfs_1 )"
|
||||
|
||||
if [ ! "$mtdnum2" ]; then
|
||||
echo "cannot find second ubi mtd partition rootfs_1"
|
||||
return 1
|
||||
fi
|
||||
|
||||
local ubidev2="$( nand_find_ubi rootfs_1 )"
|
||||
if [ ! "$ubidev2" ] && [ -n "$mtdnum2" ]; then
|
||||
ubiattach -m "$mtdnum2"
|
||||
ubidev2="$( nand_find_ubi rootfs_1 )"
|
||||
fi
|
||||
|
||||
ubirmvol /dev/$ubidev -N ubi_rootfs_data &> /dev/null || true
|
||||
ubirmvol /dev/$ubidev2 -N kernel &> /dev/null || true
|
||||
}
|
||||
@ -10,6 +10,11 @@ platform_check_image() {
|
||||
|
||||
platform_do_upgrade() {
|
||||
case "$(board_name)" in
|
||||
buffalo,wxr-2533dhp)
|
||||
buffalo_upgrade_prepare_ubi
|
||||
CI_ROOTPART="ubi_rootfs"
|
||||
nand_do_upgrade "$ARGV"
|
||||
;;
|
||||
compex,wpq864|\
|
||||
netgear,d7800 |\
|
||||
netgear,r7500 |\
|
||||
|
||||
@ -0,0 +1,535 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
#include "qcom-ipq8064-v2.0.dtsi"
|
||||
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "Buffalo WXR-2533DHP";
|
||||
compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
|
||||
|
||||
memory@42000000 {
|
||||
reg = <0x42000000 0x1e000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
ranges;
|
||||
rsvd@41200000 {
|
||||
reg = <0x41200000 0x300000>;
|
||||
no-map;
|
||||
};
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &gsbi4_serial;
|
||||
|
||||
led-boot = &power;
|
||||
led-failsafe = &diag;
|
||||
led-running = &power;
|
||||
led-upgrade = &power;
|
||||
};
|
||||
|
||||
chosen {
|
||||
/* use "ubi_rootfs" volume in "ubi" partition as rootfs */
|
||||
bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
soc {
|
||||
nand@1ac00000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&nand_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs@0 {
|
||||
reg = <0>;
|
||||
compatible = "qcom,nandcs";
|
||||
|
||||
nand-ecc-strength = <4>;
|
||||
nand-bus-width = <8>;
|
||||
nand-ecc-step-size = <512>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
ubi@0 {
|
||||
label = "ubi";
|
||||
reg = <0x0000000 0x4000000>;
|
||||
};
|
||||
|
||||
rootfs_1@4000000 {
|
||||
label = "rootfs_1";
|
||||
reg = <0x4000000 0x4000000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
mdio {
|
||||
compatible = "virtual,mdio-gpio";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
|
||||
<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
|
||||
pinctrl-0 = <&mdio0_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
qca,ar8327-initvals = <
|
||||
0x00004 0x07600000 /* PAD0_MODE */
|
||||
0x00008 0x01000000 /* PAD5_MODE */
|
||||
0x0000c 0x00000080 /* PAD6_MODE */
|
||||
0x00050 0xcc35cc35 /* LED_CTRL0 */
|
||||
0x00054 0xca35ca35 /* LED_CTRL1 */
|
||||
0x00058 0xc935c935 /* LED_CTRL2 */
|
||||
0x0005c 0x03ffff00 /* LED_CTRL3 */
|
||||
0x000e4 0x0006a545 /* MAC_POWER_SEL */
|
||||
0x000e0 0xc74164de /* SGMII_CTRL */
|
||||
0x0007c 0x0000007e /* PORT0_STATUS */
|
||||
0x00094 0x0000007e /* PORT6_STATUS */
|
||||
>;
|
||||
};
|
||||
|
||||
ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
usb {
|
||||
label = "wxr-2533dhp:green:usb";
|
||||
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "usbport";
|
||||
trigger-sources = <&hub_port0 &hub_port1>;
|
||||
};
|
||||
|
||||
guestport {
|
||||
label = "wxr-2533dhp:green:guestport";
|
||||
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
diag: diag {
|
||||
label = "wxr-2533dhp:orange:diag";
|
||||
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
internet_orange {
|
||||
label = "wxr-2533dhp:orange:internet";
|
||||
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
internet_white {
|
||||
label = "wxr-2533dhp:white:internet";
|
||||
gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wireless_orange {
|
||||
label = "wxr-2533dhp:orange:wireless";
|
||||
gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
wireless_white {
|
||||
label = "wxr-2533dhp:white:wireless";
|
||||
gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
router_orange {
|
||||
label = "wxr-2533dhp:orange:router";
|
||||
gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
|
||||
router_white {
|
||||
label = "wxr-2533dhp:white:router";
|
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
power: power {
|
||||
label = "wxr-2533dhp:white:power";
|
||||
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
power {
|
||||
label = "power";
|
||||
gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_POWER>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
eject {
|
||||
label = "eject";
|
||||
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_EJECTCD>;
|
||||
};
|
||||
|
||||
guest {
|
||||
label = "guest";
|
||||
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_0>;
|
||||
};
|
||||
|
||||
ap {
|
||||
label = "ap";
|
||||
gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
router {
|
||||
label = "router";
|
||||
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
auto {
|
||||
label = "auto";
|
||||
gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <BTN_1>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&adm_dma {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gmac1 {
|
||||
status = "okay";
|
||||
|
||||
phy-mode = "rgmii";
|
||||
qcom,id = <1>;
|
||||
|
||||
pinctrl-0 = <&rgmii2_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
mtd-mac-address = <&ART 6>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gmac2 {
|
||||
status = "ok";
|
||||
|
||||
phy-mode = "sgmii";
|
||||
qcom,id = <2>;
|
||||
|
||||
mtd-mac-address = <&ART 0>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&gsbi4 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
};
|
||||
|
||||
&gsbi4_serial {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&uart0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&gsbi5 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_SPI>;
|
||||
|
||||
spi@1a280000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&spi_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
spi-max-frequency = <50000000>;
|
||||
reg = <0>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
SBL1@0 {
|
||||
label = "SBL1";
|
||||
reg = <0x0 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
MIBIB@10000 {
|
||||
label = "MIBIB";
|
||||
reg = <0x10000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL2@30000 {
|
||||
label = "SBL2";
|
||||
reg = <0x30000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SBL3@60000 {
|
||||
label = "SBL3";
|
||||
reg = <0x60000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
DDRCONFIG@90000 {
|
||||
label = "DDRCONFIG";
|
||||
reg = <0x90000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
SSD@a0000 {
|
||||
label = "SSD";
|
||||
reg = <0xa0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
TZ@b0000 {
|
||||
label = "TZ";
|
||||
reg = <0xb0000 0x30000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
RPM@e0000 {
|
||||
label = "RPM";
|
||||
reg = <0xe0000 0x20000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBL@100000 {
|
||||
label = "APPSBL";
|
||||
reg = <0x100000 0x70000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBLENV@170000 {
|
||||
label = "APPSBLENV";
|
||||
reg = <0x170000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
ART: ART@180000 {
|
||||
label = "ART";
|
||||
reg = <0x180000 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
BOOTCONFIG@1c0000 {
|
||||
label = "BOOTCONFIG";
|
||||
reg = <0x1c0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
APPSBL_1@1d0000 {
|
||||
label = "APPSBL_1";
|
||||
reg = <0x1d0000 0x70000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hs_phy_0 { /* USB3 port 0 HS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_0 { /* USB3 port 0 SS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hs_phy_1 { /* USB3 port 1 HS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ss_phy_1 { /* USB3 port 1 SS phy */
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb3_0 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&usb_pwr_en_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&usb3_1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dwc3_0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hub_port0: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&dwc3_1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
hub_port1: port@1 {
|
||||
reg = <1>;
|
||||
#trigger-source-cells = <0>;
|
||||
};
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie1 {
|
||||
status = "okay";
|
||||
force_gen1 = <1>;
|
||||
};
|
||||
|
||||
&qcom_pinmux {
|
||||
button_pins: button_pins {
|
||||
mux {
|
||||
pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
|
||||
"gpio58", "gpio64", "gpio65";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led_pins {
|
||||
mux {
|
||||
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
|
||||
"gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
uart0_pins: uart0_pins {
|
||||
mux {
|
||||
pins = "gpio10", "gpio11";
|
||||
function = "gsbi4";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
spi_pins: spi_pins {
|
||||
mux {
|
||||
pins = "gpio18", "gpio19", "gpio21";
|
||||
function = "gsbi5";
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
data {
|
||||
pins = "gpio18", "gpio19";
|
||||
drive-strength = <10>;
|
||||
};
|
||||
|
||||
cs{
|
||||
pins = "gpio20";
|
||||
drive-strength = <10>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
clk {
|
||||
pins = "gpio21";
|
||||
drive-strength = <12>;
|
||||
};
|
||||
};
|
||||
|
||||
mdio0_pins: mdio0_pins {
|
||||
mux {
|
||||
pins = "gpio0", "gpio1";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
nand_pins: nand_pins {
|
||||
mux {
|
||||
pins = "gpio34", "gpio35", "gpio36",
|
||||
"gpio37", "gpio38", "gpio39",
|
||||
"gpio40", "gpio41", "gpio42",
|
||||
"gpio43", "gpio44", "gpio45",
|
||||
"gpio46", "gpio47";
|
||||
function = "nand";
|
||||
drive-strength = <10>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
pullups {
|
||||
pins = "gpio39";
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
hold {
|
||||
pins = "gpio40", "gpio41", "gpio42",
|
||||
"gpio43", "gpio44", "gpio45",
|
||||
"gpio46", "gpio47";
|
||||
bias-bus-hold;
|
||||
};
|
||||
};
|
||||
|
||||
rgmii2_pins: rgmii2_pins {
|
||||
mux {
|
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
|
||||
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
|
||||
function = "rgmii2";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
usb_pwr_en_pins: usb_pwr_en_pins {
|
||||
mux{
|
||||
pins = "gpio68";
|
||||
function = "gpio";
|
||||
drive-strength = <2>;
|
||||
bias-pull-up;
|
||||
output-high;
|
||||
};
|
||||
};
|
||||
};
|
||||
@ -972,7 +972,7 @@
|
||||
|
||||
status = "disabled";
|
||||
|
||||
dwc3@11000000 {
|
||||
dwc3_0: dwc3@11000000 {
|
||||
compatible = "snps,dwc3";
|
||||
reg = <0x11000000 0xcd00>;
|
||||
interrupts = <0 110 0x4>;
|
||||
@ -997,7 +997,7 @@
|
||||
|
||||
status = "disabled";
|
||||
|
||||
dwc3@10000000 {
|
||||
dwc3_1: dwc3@10000000 {
|
||||
compatible = "snps,dwc3";
|
||||
reg = <0x10000000 0xcd00>;
|
||||
interrupts = <0 205 0x4>;
|
||||
|
||||
@ -3,6 +3,13 @@
|
||||
include $(TOPDIR)/rules.mk
|
||||
include $(INCLUDE_DIR)/image.mk
|
||||
|
||||
define Build/buffalo-rootfs-cksum
|
||||
( \
|
||||
echo -ne "\x$$(od -A n -t u1 $@ | tr -s ' ' '\n' | \
|
||||
$(STAGING_DIR_HOST)/bin/awk '{s+=$$0}END{printf "%x", 255-s%256}')"; \
|
||||
) >> $@
|
||||
endef
|
||||
|
||||
define Device/Default
|
||||
PROFILES := Default
|
||||
KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts)
|
||||
@ -72,6 +79,21 @@ define Device/ZyXELImage
|
||||
IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
endef
|
||||
|
||||
define Device/buffalo_wxr-2533dhp
|
||||
$(call Device/LegacyImage)
|
||||
DEVICE_DTS := qcom-ipq8064-wxr-2533dhp
|
||||
DEVICE_TITLE := Buffalo WXR-2533DHP
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 65536k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES := sysupgrade.bin
|
||||
IMAGE/sysupgrade.bin := append-rootfs | buffalo-rootfs-cksum | \
|
||||
sysupgrade-tar rootfs=$$$$@ | append-metadata
|
||||
DEVICE_PACKAGES := ath10k-firmware-qca99x0-ct
|
||||
endef
|
||||
TARGET_DEVICES += buffalo_wxr-2533dhp
|
||||
|
||||
define Device/compex_wpq864
|
||||
$(call Device/FitImage)
|
||||
$(call Device/UbiFit)
|
||||
|
||||
@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
|
||||
--- a/arch/arm/boot/dts/Makefile
|
||||
+++ b/arch/arm/boot/dts/Makefile
|
||||
@@ -699,6 +699,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
@@ -699,6 +699,18 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8084-mtp.dtb \
|
||||
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
||||
qcom-ipq8064-ap148.dtb \
|
||||
@ -23,6 +23,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
|
||||
+ qcom-ipq8064-r7500v2.dtb \
|
||||
+ qcom-ipq8064-wg2600hp.dtb \
|
||||
+ qcom-ipq8064-wpq864.dtb \
|
||||
+ qcom-ipq8064-wxr-2533dhp.dtb \
|
||||
+ qcom-ipq8065-nbg6817.dtb \
|
||||
+ qcom-ipq8065-r7800.dtb \
|
||||
qcom-msm8660-surf.dtb \
|
||||
|
||||
Loading…
Reference in New Issue
Block a user