mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-22 23:12:32 +00:00
51fe956c4f
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
59 lines
2.0 KiB
Bash
Executable File
59 lines
2.0 KiB
Bash
Executable File
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
board_config_update
|
|
|
|
board=$(board_name)
|
|
boardname="${board##*,}"
|
|
|
|
case "$board" in
|
|
buffalo,wxr-2533dhp)
|
|
ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:white:wireless" "phy0tpt"
|
|
ucidef_set_led_switch "wan" "WAN" "${boardname}:white:internet" "switch0" "0x20"
|
|
;;
|
|
compex,wpq864)
|
|
ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1"
|
|
;;
|
|
nec,wg2600hp)
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy1tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy0tpt"
|
|
ucidef_set_led_switch "wan" "WAN" "${boardname}:green:active" "switch0" "0x1e"
|
|
;;
|
|
netgear,d7800 |\
|
|
netgear,r7500 |\
|
|
netgear,r7500v2 |\
|
|
netgear,r7800)
|
|
ucidef_set_led_usbport "usb1" "USB 1" "${boardname}:white:usb1" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_usbport "usb2" "USB 2" "${boardname}:white:usb2" "usb3-port1" "usb4-port1"
|
|
ucidef_set_led_netdev "wan" "WAN" "${boardname}:white:wan" "eth0"
|
|
ucidef_set_led_ide "esata" "eSATA" "${boardname}:white:esata"
|
|
;;
|
|
tplink,c2600)
|
|
ucidef_set_led_usbport "usb1" "USB 1" "${boardname}:white:usb_2" "usb1-port1" "usb2-port1"
|
|
ucidef_set_led_usbport "usb2" "USB 2" "${boardname}:white:usb_4" "usb3-port1" "usb4-port1"
|
|
ucidef_set_led_switch "wan" "wan" "${boardname}:white:wan" "switch0" "0x20"
|
|
ucidef_set_led_switch "lan" "lan" "${boardname}:white:lan" "switch0" "0x1e"
|
|
;;
|
|
tplink,vr2600v)
|
|
ucidef_set_led_usbport "usb" "USB" "${boardname}:white:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1"
|
|
ucidef_set_led_switch "lan" "lan" "${boardname}:white:lan" "switch0" "0x1e"
|
|
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:white:wlan2g" "phy0tpt"
|
|
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:white:wlan5g" "phy1tpt"
|
|
ucidef_set_led_switch "wan" "wan" "${boardname}:white:wan" "switch0" "0x20"
|
|
;;
|
|
zyxel,nbg6817)
|
|
ucidef_set_led_netdev "wan" "WAN" "${boardname}:white:internet" "eth1"
|
|
;;
|
|
*)
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|