Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
In rtl83xx_set_features we set bit 3 to enable, and bit 4 to disable
checksuming. Looking at rtl93xx_set_features we however see that for
both enable and disable the same bit is used (bit 4). This can't be
right, especially as bit 4 for rtl83xx seems to be Collision threshold
occupying 2 bits. Change this to make this more logical.
Fixes: 9e8d62e421 ("realtek: enable CRC offloading")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
L2 learning on the CPU port is currently not consistently configured and
relies on the default configuration of the device. On RTL83xx, it is
disabled for packets transmitted with a TX header, as hardware learning
corrupts the forwarding table otherwise. As a result, unneeded flooding
of traffic for the CPU port can already happen on some devices now. It
is also likely that similar issues exist on RTL93xx, which doesn't have
a field to disable learning in the TX header.
To address this, disable hardware learning for the CPU port globally on
all devices. Instead, enable assisted learning to let DSA write FDB
entries to the switch.
For now, this does not sync local/bridge entries to the switch. However,
support for that was added in Linux 5.14, so the next switch to a newer
kernel version is going to fix this.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Initialize the data structure using memset to avoid the possibility of
writing garbage values to the hardware.
Always set a valid entry type, which should fix writing unicast entries
on RTL930x.
For unicast entries, set the is_static flag to prevent the switch from
aging them out.
Also set the rvid field for unicast entries. This is not strictly
necessary, as the switch fills it in automatically from a non-zero vid.
However, this makes the code consistent with multicast entry setup.
While at it, reorder the statements and fix some style issues (double
space, comma instead of semicolon at end of statement). Also remove the
unneeded priv parameter and debug print for the multicast entry setup
function.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.
Reintroduce it to fix Asrock G10 functionality.
Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.
Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.
Revert this to swconfig driver to restore normal functionality.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.
Backport patch that fix this error and correctly handle error from
partition parser.
Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch from kernel 5.15 that mute error on EPROBE_DEFER with
smempart parser.
This parser require the smem device to be probed first and currently it
may happen that mtd gets probed before the smem device causing an error
on the smempart parser. This error may be confusing and should be muted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In new kernel version from 5.16, smem node can be declared directly in
the reserved-space node. Upstream ipq806x (and to-be-merged) ipq807x
allign to this new implementation. Backport this patch to kernel 5.15 to
fix support for smem parser for ipq806x target.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move patch wrongly placed in backport dir to pending dir as they still
didn't got merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move MGLRU patches from pending to backport as they got merged upstream.
These are direct porting from one of the dev so it's better to just move
than trying to backport them again from upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move mvebu aardvark patch from pending to backport as they got merged
upstream.
One additional patch is needed as a later fixup for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move sfp HALNy patch from pending to backport as they got merged
upstream. The patch was reordered and one was squashed in the upstream
variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The switches support different actions for incoming ethernet multicast
frames with Reserved Multicast Addresses (01-80-C2-00-00-{01-2F}). The
current code will set the 2-bit action field to FLOOD (0x3) for most
classes, but the highest bit is always unset for the relevant control
registers. This means the DROP (0x1) action being used for these
classes; whatever class the MSB happens to be in.
For RTL838x, this results in {20,23-2F} frames being dropped, instead of
flooding all ports. On other switch generations, {0F,1F,2F} frames are
dropped. This is inconsistent, and appears to be a mistake. Remove this
inconsistency by flooding all multicast frames with RMA addresses.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The multicast setup function rtl838x_eth_set_multicast_list() checks if
the current SoC is a RTL839x family device. However, the function is
only included in the RTL838x ops table, so this path should never be
taken, making this dead code. rtl839x_eth_set_multicast_list() is
already present in the RTL839x ops table, so it should be safe to remove
this branch.
While touching the code, also re-sort the functions to match sorting
elsewhere, with rtl838x coming before rtl839x.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Currently several messages at KERN_INFO level are printed for every FDB
del/dump operation. This can cause a significant slowdown for example
while using "bridge fdb", and may even trigger a watchdog.
Remove most of these log messages, as the new L2 table debugfs node
should be a good replacement. Change the remaining messages to
KERN_DEBUG level.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Switch to a polling implementation similar to the one for RTL838x, to
allow other kernel tasks to run while waiting.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The new timer is not yet ready for all targets. Avoid interactive
questions during build
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[rename symbol to CONFIG_REALTEK_OTTO_TIMER]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use the new timer driver for the RTL839X devices and remove the
no longer needed modules.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use the new timer driver for the RTL838X devices. Remove the no
longer needed modules.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Provide some helpful information about the devicetree configuration of
our new driver
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct compatible order in examples]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Now that we provide a clock driver for the Reltek SOCs the CPU frequency might
change on demand. This has direct visible effects during operation
- the CEVT 4K timer is no longer a stable clocksource
- after CPU frequencies changes time calculation works wrong
- sched_clock falls back to kernel default interval (100 Hz)
- timestamps in dmesg have only 2 digits left
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps ...
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.080000] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.090000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ...
Looking around where we can start the CEVT timer for RTL930X is a good basis.
Initially it was developed as a clocksource driver for the broken timer in that
specific SOC series. Afterwards it was shifted around to the CEVT location,
got SMP enablement and lost its clocksource feature. So we at least have
something to copy from. As the timers on these devices are well understood
the implementation follows this way:
- leave the RTL930X implementation as is
- provide a new driver for RTL83XX devices only
- swap RTL930X driver at a later time
Like the clock driver this patch contains a self contained module that is SOC
independet and already provides full support for the RTL838X, RTL839X and
RTL930X devices. Some of the new (or reestablished) features are:
- simplified initialization routines
- SMP setup with CPU hotplug framework
- derived from LXB clock speed
- supplied clocksource
- dedicated register functions for better readability
- documentation about some caveats
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[remove unused header includes, remove old CONFIG_MIPS dependency, add
REALTEK_ prefix to driver symbol]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Undo parts of these:
116feb4a1c ipq40xx: remove non-converted network configs
db19efee95 ipq40xx: disable boards not converted to DSA
Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock
bootloader has memorized them (instead of following aliases); then plug
the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the
'local-mac-address' property is no longer in the correct node.
Cc: David Bauer <mail@david-bauer.net>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Convert to DSA and enable the MobiPromo CM520-79F device again.
Signed-off-by: Jack Chen <redchenjs@live.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
This fixes reference clock frequency of RB912. 25 MHz frequency leads
to system clock running too fast, uptime incrementing too fast and
delays (like `sleep 10`) returning too early.
Board has quartz with NSK 3KHAA Z 40 000 marking.
Signed-off-by: Pavel Kamaev <pavel@kamaev.me>
Manufacturer has predetermined mac address values for lan and wan ports.
This change keeps inline with other mt7621 devices mac address allocation
from factory mtd partition.
Example from hexdump output:
0xe000 0x6 (lan) - 0xe006 0x6 (wan)
0000e000 70 b3 d5 10 02 96 70 b3 d5 10 02 95 ff ff ff ff
Previous change had created an overlapping mac address situation as it
would increment by one based on the lan mac address location found in the
factory partition, which would sometimes increment to the same as the
mt7603 wifi chip.
Tested on Unielec u7621-01 model
Signed-off-by: David Bentham <db260179@gmail.com>
The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are
exactly the same, both of which are customized by operators.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
0001-MIPS-lantiq-add-pcie-driver.patch needs to drop
MODULE_SUPPORTED_DEVICE because that macro is gone on newer kernels.
Add checks for copy_{to,from}_user in
0008-MIPS-lantiq-backport-old-timer-code.patch which is now mandatory.
0705-v5.13-net-dsa-lantiq-allow-to-use-all-GPHYs-on-xRX300-and-.patch
get dropped because it's a backport from Linux 5.13.
All other patches are refreshed.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This convert board asus,rt-ac42u to DSA and re-enable it
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Copy kernel config and patches from 5.10. Along with it
individual targets' config-default from 5.10 has been moved to
config-5.10.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fix typo ('_' vs '-') and add #cooling-cells to gpio-fan to get
thermal zone into functional state.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This comit fixes warnings that occur on kernel 5.15:
...
[ 2.269736] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 1e108000.switch-mii:00:
PHY has delays (e.g. via pin strapping), but phy-mode = 'rgmii'
[ 2.269736] Should be 'rgmii-id' to use internal delays txskew:1500 ps rxskew:1500 ps
...
Ref: be393dd685
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Just one device builds seama images so let's just fix up
seama on that one device. I guess the tool errors out but
this feels cleaner.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[rmilecki: drop "fixtrx" from D-Link case]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the
4366b1 wireless chip and tries to load the firmware file which doesn't
exist because it's not included in the image.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The most common CPU governor in the OpenWRT project is currently ondemand (see
below). Switch mt7622 over to it as well.
Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'
ondemand: 16
performance: 5
schedutil: 5
userspace: 2
Build system: x86_64
Build-tested: ramips/mt7621
Signed-off-by: John Audia <graysky@archlinux.us>
Remove kmod-sdhci-mtk as the mtk-sd driver is built-in anyway for the
relevant subtargets in order to support mounting rootfs from eMMC or
SD card.
Add kmod-iio-mt6577-auxadc to support reading the raw values from the
auxadc unit used as in-SoC thermal sensor. This driver was previously
built-in, but as thermal itself works well without it there is no use
for it in every day use of a device. Build the module to still allow
access to the raw values for those who need it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
As done previously, this preserves the MAC addresses of they physical
Ethernet ports. The interfaces are renamed as eth0 is in use for the
native GMAC; the new interface naming matches the physical port labels.
- sw-eth1 corresponds to the physical port labeled ETH1 and has the
base MAC address. This port can be used to power the device.
- sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC
address one greater than the base.
As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Get MAC address of WAN from HW.WAN.MAC.Address in hwconfig partition
instead of calculated one from wlan's address.
And added label_mac.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use NVMEM "calibration" implementation for ath9k/ath10k(-ct) on ELECOM
WRC-300GHBK2-I and WRC-1750GHBK2-I/C instead of mtd-cal-data property
or user-space script.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Use ARTIFACTS to generate factory image of the following ELECOM devices
instead of redundant recipe which generate on KERNEL_INITRAMFS.
- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
To use from the following devices in ath79 target, move edimax-header to
image-commands.mk.
- ELECOM WRC-300GHBK2-I
- ELECOM WRC-1750GHBK2-I/C
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Set 5.15 as default kernel. Testing support was already added on
29.03.2021.
Testing support was added in
9b3bc5d119 ("x86: enable 5.15 as testing kernel").
[0] - edd6021465
Tested-by: Mark Mentovai <mark@mentovai.com>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Don't reply on mapped rootfs partition but rather just take what ever
has been set to the kernel cmdline root= parameter as a hint to decide
which media to install sysupgrade to on the BananaPi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* remove orphaned Kconfig symbol now that CONFIG_IIO is no longer
selected after commit ef8b935c95 ("mediatek: clean up mt7622 kernel config")
* select UBI fast-map feature to decrease boot time and keep the
number of spare blocks required in sync with U-Boot's expectations
(we got fast-map enabled in U-Boot)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch headers and description for pending patch.
Add version tag to patch already merged upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This gets rid of "nvmem-cells" limitation. Dynamic partitions can be
defined for any (sub)partitions layout.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add for mtd-parsers-trx-allow-to-use-on-MediaTek-MIPS-SoCs.patch and
hwmon-lm70-Add-ti-tmp125-support.patch the 5.18 tag as it was merged
in kernel 5.18.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Instead of trying to figure out the actual root device, just use the
kernel 'root' cmdline parameter as a hint to decide which device to
flash to.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use UBI fast map feature to avoid scanning the whole flash on each
boot which takes several seconds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When I enabled CONFIG_HOTPLUG_PCI for mvebu platform, it was asking for
more symbols.
Fixes:
Support for PCI Hotplug (HOTPLUG_PCI) [Y/?] y
CompactPCI Hotplug driver (HOTPLUG_PCI_CPCI) [N/y/?] n
SHPC PCI Hotplug driver (HOTPLUG_PCI_SHPC) [N/y/?] (NEW)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #10645
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Similar to the lzma-loader on our MIPS targets, the spi-loader acts as
a second-stage loader that will then load and start the actual kernel.
As the TL-WDR4900 uses SPI-NOR and the P1010 family does not have support
for memory mapping of this type of flash, this loader needs to contain a
basic driver for the FSL ESPI controller.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Backport qca8k fixup patches for inband mgmt on Big-Endian systems.
This is needed for ath79 and mpc85xx targets that are Big-Endian and use
qca8k based switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.
Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.
The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.
Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
The generic imagebuilder does not have a generic in the name, although
this is the default naming scheme. Apply the same fix as for the octeon
target. Thanks to @dangowrt for reporting that the same issues applies
also for the airoha target.
Before the fix:
openwrt-imagebuilder-airoha.Linux-x86_64.tar.xz
After:
openwrt-imagebuilder-airoha-generic.Linux-x86_64.tar.xz
Signed-off-by: Nick Hainke <vincent@systemli.org>
Linksys ea6500-v2 have 256MB of ram. Currently we only use 128MB.
Expand the definition to use all the available RAM.
Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
[ wrap to 80 columns ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream has switched to gnu11 not too long ago. One advantage of
backporting this to these older kernels is, that we can encourage and
write better upstreamable kernels. E.g. the kernel devs prefer loop
declarations. Shrinking the master/local gap will be useful in these
cases.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Change GPIO from 10 to 35 to make it works as expected
Fixes: 0de6a3339f ("ipq40xx: Add ZTE MF289F")
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Add multiple patch for krait-cc modernization and multiple fixup for the
driver. Also modify a patch to enable the qsb fixed clock and add pxo to
krait-cc node.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
nand_pins definition is now shipped in ipq8064 dtsi. Rework the
nand_pins definition for wg2600hp3 5.15 files.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch has changed implementation and now the binding has changed.
Replace the old binding with boot-partitions and reimplement the
definition with the new definition.
The new definition is:
<offset1 size1 offset2 size2 offset3 ...>
and now supports sparsed patch.
Also add missing binding in some dts and add the backup boot partition
to the boot-partitions list.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove useless spm patch as using the normal qcom,spm compatible is
enough to register it with no clks.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use a new implementation by using a devfreq driver to scale the shared
cache of the krait cpu cores.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport devfreq new cpufreq based PASSIVE governor needed for devfreq
based fab and cache scaling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reorganize dtsi patches with upstream version and drop dtsi in 5.15
files.
Also add an additional upstream patch for hwspinlock support.
Refresh all the dts with needed changes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This doesn't cause any panic anymore and no regression are observed with
ath10k. Remove this additional patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Remove qcom adm Documentation patch that is not needed for the target.
Probably a leftover when the adm bus was added, now merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In preparation for a cleanup of 5.15 patches copy the files dir to 5.10
and 5.15 kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The CPU port should define the phy-mode and and a PHY phandle or
fixed-link to indicate how the CPU port is connected to the SoC's
Ethernet controller. On xRX200 this is all internal connection, so use
phy-mode = "internal" along with a fixed-link that matches the
definition inside ð0.
Linux 6.0 shows a warning since upstream commit e09e9873152e3f ("net:
dsa: make phylink-related OF properties mandatory on DSA and CPU
ports"). when these properties are missing. Adding the properties
before OpenWrt is updated to Linux 6.0 is harmless.
Suggested-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
This patch converts networking on Sony NCP-HG100/Cellular to DSA and
re-enables support for the device.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Convert ZTE MF289F device to DSA, re-order network ports to match the
labels on the case and re-enable the device.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
* set correct clocks for PWM to work.
* MT7986 PWM does have the 26MHz-clock-select, set that in patch
* drop useless 'passive' trip point in thermal zone
* extend pwm-fan to have 3 active operating points
* set reasonable trip points in thermal zone
* invert pwm-fan operating points and set shorter period to allow
less noisy operation of the PWM fan of the BPi-R3.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In *_enable_learning() only address learning should be configured, so
remove enabling forwarding. Forwarding is configured by the respective
*_enable_flood() functions.
Clean up both functions for RTL838x and RTL839x, and fix the comment on
the number of entries.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[squash RTL838x, RTL839x changes]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Those messages should be printed when entry was found (idx >= 0). Move
them to the right place to not print invalid entry indices.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amden commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The initial state of sds_mode in rtl9300_force_sds_mode() is null and it
will be configured in switch-case. So print message after it.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Use the generic function of MIPS in Linux Kernel instead of open coding
our own initialisation.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[amend commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The availabibity of probing CPC depends on CONFIG_MIPS_CPC symbol and it
will be checked in arch/mips/include/asm/mips-cpc.h. RTL9310 selects
this symbol, so the family check is redudant.
Furthermore, mips_cm_probe() is already called from setup_arch() in
mips/kernel/setup.c before prom_init(), and as such is not required.
Also move mips_cpc_probe() to run just before registering SMP ops.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[squash SMP change commits, reword commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
---
This patch only really has an impact on the rtl931x subtarget, which has
no devices. Noboby is currently set up to test these patches either, but
the end result is closer to MIPS_GENERIC, so I do not expect it to cause
issues.
RTL8231 and ethernet phys are not on the same bus, so separate the lock
to each own to cut off the unnecessary dependency.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Everywhere else the device is referred to as WS-AP3805i,
only the model name wrongly only said AP3805i.
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Setup thermal zone, select pins and enabled drivers for I2C (on 26-pin
GPIO bank) and PWM (1x fan and 1x GPIO bank).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for hardware I2C and PWM units found in the Filogic SoCs
as well as the CPU thermal support.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows the user to specify a larger tx ring buffer size via ethtool.
Having symmetrical ring buffer sizes increases throughput on high bandwidth
(1 gbps tested) network connections.
The default value is not changed so the same behaviour is saved.
Signed-off-by: Robert Meijer <robert.s.meijer@gmail.com>
[ improve title, commit description and wrap to 80 columns ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert pakedge_wr-1 device to DSA and enable it.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>i
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert luma_wrtq-329acn device to DSA and enable it.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface
corresponding to the non-existing port.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
When testing the DSA changes with 5.15.60 kernel, I've noticed, that the
MAC addresses are not properly configured, there is single MAC being
used for LAN and WAN interfaces:
eth0: 94:83:c4:XX:YY:4a (MAC on sticker)
lan1@eth0: 94:83:c4:XX:YY:4a
lan2@eth0: 94:83:c4:XX:YY:4a
wan@eth0: 94:83:c4:XX:YY:4a
wlan0: 94:83:c4:XX:YY:4a
wlan1: 94:83:c4:XX:YY:4b
The same config, prior to the DSA conversion:
lan/eth0: 94:83:c4:XX:YY:4a (MAC on sticker)
wan/eth1: 94:83:c4:XX:YY:4b
wlan0: 94:83:c4:XX:YY:4a
wlan1: 94:83:c4:XX:YY:4b
Settings in ART partition:
root@OpenWrt:/# hexdump -C /dev/mtd7 | grep '94 83'
00000000 94 83 c4 XX YY 4a 94 83 c4 0e YY 4b ff ff ff ff |.....J.....K....|
00001000 20 2f 8d 8c 01 01 94 83 c4 XX YY 4a 00 00 20 00 | /.........J.. .|
00005000 20 2f 5a 3a 01 01 94 83 c4 XX YY 4b 00 00 20 00 | /Z:.......K.. .|
So let's fix it by keeping same MAC address assigment as was done before
DSA conversion and while at it, define `label-mac-device` as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove networking configs for non DSA converted boards in ipq40xx.
Currently, they are just causing clutter.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Enable threaded NAPI by default in IPQESS driver as it significantly
improves network perfromance, in my testing about 100+ Mbps in WAN-LAN
routing.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This fixes assigning random MAC to br-lan interface upon boot.
While at that, rename at24@50 node to eeprom@50, to align with upstream
device tree style.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Convert IPQ40xx boards to DSA setup.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Signed-off-by: ChunAm See <z1250747241@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Serhii and others have experienced PSGMII link degradation up to point
that it actually does not pass packets at all or packets arrive as zeros.
This usually happened after a couple of hot reboots.
Serhii has managed to track it down to PSGMII calibration not being done
properly and has fixed it, so all of the code is Serhii-s work.
Signed-off-by: Serhii Serhieiev <adron@mstnt.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since kernel 5.4 has been droppped from IPQ40xx, there is no need to keep
the version checks for kernels older than 5.10.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, suspend and resume ops are not present, this means that if user
disables a DSA interface that the PHY-s remain alive and the link is up.
Fix it by using generic PHY suspend and resume ops.
Signed-off-by: Serhii Serhieiev <adron@mstnt.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Select the Ethernet driver, DSA tag driver and the DSA driver itself to
be built in the kernel config.
They automatically pull in switchdev and phylink.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Qualcomm IPQ40xx SoC-s have a variant of QCA8337N switch built-in.
It shares most of the stuff with its external counterpart, however it is
modified for the SoC.
Namely, it doesn't have second CPU port (Port 6), so it has 6 ports
instead of 7.
It also has no built-in PHY-s but rather requires external PSGMII based
companion PHY-s (QCA8072 and QCA8075) for which it first needs to carry
out calibration before using them.
PSGMII has a SoC built-in PHY that is used to connect to the PHY-s which
unfortunately requires some magic values as the datasheet doesnt document
the bits that are being set or the register at all.
Since its built-in it is MMIO like other peripherals and doesn't have its
own MDIO bus but depends on the SoC provided one.
CPU connection is at Port 0 and it uses some kind of a internal connection
and no traditional RGMII/SGMII.
It also doesn't use in-band tagging like other qca8k switches so a shinfo
based tagger is used.
This is based on the current OpenWrt qca8k version that has been imported
from generic target.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This is just importing the qca8k driver from the generic target.
It will be used as the based for IPQ40xx version, this is just
to be able to see the diff.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
PSGMII is a Qualcomm specific mode similar to QSGMII but it has 5 SGMII
lines instead of 4 in QSGMII.
This just adds the support for the PHY layer to be able to identify the
mode for further use.
It is required for the DSA driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQESS is the EDMA replacement driver for the IPQ40xx SoC built-in
ethernet controller.
Unlike EDMA it is Phylink based and doesnt touch PHY-s directly.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
There is no point in using a DT property to trigger setting the PSGMII
PHY AZ transmitting ability.
Especially since EEE can be disabled using ethtool anyway.
Fixup the mask for setting the workaround as only BIT(0) is actually being
changed and use the phy_clear_bits_mmd helper instead of reading, then
clearing the bit and writing back as it does everything for us.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
IPQ40xx requires a special DSA tag driver despite using the QCA8337N
switch.
However they have changed the header format and the existing QCA tag
driver cannot be reused.
For details on how it actually works and else read the patch commit
description.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, QCA807x doesnt do any kind of validation to see whether it
actually supports the inserted module.
So lets add checks to allow only 1000BaseX and 100BaseFX based modules.
While adding validation, move fiber configuration to insert/remove events
instead of always doing it at config time.
This allows getting rid of the DT property for fiber enable and now only
the upstream sfp phandle is required.
Since we are refactoring fiber related code, lets heavily simplify the
status polling as the current logic is overcomplicated due to previous
wish to support non standard SFP cages that dont have pins properly
connected, that is removed now and only proper SFP cages will work.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In order to start working on IPQESS + DSA drop the old ESSEDMA + AR40xx
driver combo.
Remove the kernel symbols, disable swconfig and drop swconfig package
as they are not needed anymore.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This patch is needed to handle interrupts by the second VPE on the Lantiq
ARX100, xRX200, xRX300 and xRX330 SoCs. Switching some ICU interrupts to
the second VPE results in a hang. Currently, the vsmp_init_secondary()
function is responsible for enabling these interrupts. It only enables
Malta-specific interrupts (SW0, SW1, HW4 and HW5).
The MIPS core has 8 interrupts defined. On Lantiq SoCs, hardware
interrupts are wired to an ICU instance. Each VPE has an independent
instance of the ICU. The mapping of the ICU interrupts is shown below:
SW0(IP0) - IPI call,
SW1(IP1) - IPI resched,
HW0(IP2) - ICU 0-31,
HW1(IP3) - ICU 32-63,
HW2(IP4) - ICU 64-95,
HW3(IP5) - ICU 96-127,
HW4(IP6) - ICU 128-159,
HW5(IP7) - timer.
This patch enables all interrupt lines on the second VPE.
This problem affects multithreaded SoCs with a custom interrupt controller.
SOCs with 1004Kc core and newer use the MIPS GIC. At this point, I am aware
that the Realtek RTL839x and RTL930x SoCs may need a similar fix. In the
future, this may be replaced with some generic solution.
Tested on Lantiq xRX200.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
At some point after 21.02.3 and before 22.03.0, the size limits of the
Linksys RE6500 were reached and prevent booting from the 22.03.0 release
or builds of current SNAPSHOT. This patch allows builds of master to boot
again and has been tested on my device.
Fixes: #8577
Signed-off-by: Mark King <mark@vemek.co>
The workaround for an already-enabled R4K timer used a non-existent
macro CAUSE_DC. Fix compiling by using the actual macro CAUSEF_DC.
Fixes: b7aab19585 ("realtek: SMP handling of R4K timer interrupts")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Until now there has been no good explanation why we mess with the R4K
timer on SMP. After extensive testing and looking at the SDK code it
becomes clear what it is all about.
When we disable the CEVT_R4K module (we will do with the new timer
driver) the R4K timer hardware still fires interrupts on the secondary
CPU. To get around this we have two options:
- Disable IRQ 7
- Stop the counter completely
This patch selects option two because this is the root of evil.. To be
on the safe side we will do it only in case the CEVT_R4K module is
disabled.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The scope of the SMP startup structure is wrong. It is created on the
stack and not as a global variable. This can lead to startup failures.
Fixes: 3f41360eb7 ("realtek: use upstream recommendation for CPU start")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
OpenWRT's developer guide prefers having actual patches so they an be
sent upstream more easily.
However, in this case, Adding proper fields also allows for `git am` to
properly function. Some of these patches are quite old, and lack much
traceable history.
This commit tries to rectify that, by digging in the history to find
where and how it was first added.
It is by no means perfect and also shows some patches that should have
been long gone.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Import patches from mtk-openwrt-feeds (MTK SDK) to support reading
t-phy settings affecting PCIe as well as USB2 and USB3 from efuse.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
efuse is used to store board-specific settings of some of the in-SoC
peripherals. Add it to device tree, so it gets probed on boot and can
be accessed by other drivers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow byte-wise access to mtk-efuse as some drivers require that.
Patch imported from mtk-openwrt-feeds (MTK SDK).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The corresponding kmod package is marked as HIDDEN and selected by all
other kernel modules that need it, so the kconfig side will be in sync
without manual selection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fixes build warnings when using newer versions of grep.
Signed-off-by: Chris Osgood <chris_github@functionalfuture.com>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Convert MAC address and label_mac configuration of Buffalo
WSR-1166DHP to use the generic function of OpenWrt.
Apply commit 770cfe9 for WCR-1166DS to WSR-1166DHP too.
Tested on the device and MAC address is kept before and after this
change.
Signed-off-by: Kazuhiro Ito <kzhr@d1.dion.ne.jp>
Instead of dropping *fix-typo-in-__mtk_foe_entry.patch which effectively
means keeping the (also wrong) assignment of MTK_FOE_STATE_BIND, rather
use MTK_FOE_STATE_INVALID as that works well on both older (NETSYS_V1)
and newer (NETSYS_V2) MediaTek SoCs.
Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
When the realtek clock driver was introduced, CONFIG_COMMON_CLK_REALTEK
was not correctly disabled for other subtarget. Add the missing config
flag to fix compilation error on buildbot.
Fixes: 4850bd887c ("realtek: add RTL83XX clock driver")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move and rename patches which were merged upstream and import follow-up
fixes for MediaTek Ethernet offloading features on MT7622 and Filogic
platforms. Remove patch
793-net-ethernet-mtk_eth_soc-fix-typo-in-__mtk_foe_entry.patch
which breaks hardware flow offloading on MT7622, it will be reverted
upstream as well.
Fixes: c93c5365c0 ("kernel: pick patches for MediaTek Ethernet from linux-next")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Don't overwrite AS_DPM and L2LEARNING flags when dest_port is >= 32.
Fixes: 1773264a0c ("realtek: correct egress frame port verification")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The generic imagebuilder does not have a generic in the name, although
this is the default naming scheme. Use bcm53xx as template for this fix.
Before the fix:
openwrt-imagebuilder-octeon.Linux-x86_64.tar.xz
After:
openwrt-imagebuilder-octeon-generic.Linux-x86_64.tar.xz
Signed-off-by: Nick Hainke <vincent@systemli.org>
If this module is not set to y, then I get the following compilation
error during geode build.
Package kmod-w83627hf-wdt is missing dependencies for the following libraries:
watchdog.ko
Setting the linux CONFIG_WATCHDOG_CORE to y as in all other targets
fixes this issue.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
If this module is not set to y, then I get the following compilation
error during geode build.
Package kmod-w83627hf-wdt is missing dependencies for the following
libraries:
watchdog.ko
Setting the linux CONFIG_WATCHDOG_CORE to y as in all other targets
fixes this issue.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA)
and Vodafone DE\T-Mobile PL (called GigaCube).
Modem is a MiniPCIe-to-USB based on Snapdragon X24,
it supports 4CA aggregation.
There are currently two hardware revisions, which
differ on the 5Ghz radio:
AT1 = QCA9984 5Ghz Radio on PCI-E bus
AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz
Device specification
--------------------
SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz:
(QCA9984): a/n/ac, 4x4 HW REV AT1
(IPA4019): a/n/ac, 2x2 HW REV AT2
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot
Installation
------------
1. Place OpenWrt initramfs image for the device on a TFTP
in the server's root. This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial connector
GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX
(refer to this image: https://ibb.co/31Gngpr).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. Stop in u-Boot (using ESC button) and run u-Boot commands:
setenv serverip 192.168.0.2
setenv ipaddr 192.168.0.1
set fdt_high 0x85000000
tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb
bootm $loadaddr
5. Please make backup of original partitions, if you think about revert to
stock, specially mtd16 (Web UI) and mtd17 (rootFS).
Use /tmp as temporary storage and do:
WEB PARITION
--------------------------------------
cat /dev/mtd16 > /tmp/mtd16.bin
scp /tmp/mtd16.bin root@YOURSERVERIP:/
rm /tmp/mtd16.bin
ROOT PARITION
--------------------------------------
cat /dev/mtd17 > /tmp/mtd17.bin
scp /tmp/mtd17.bin root@YOURSERVERIP:/
rm /tmp/mtd17.bin
6. Login via ssh or serial and remove stock partitions
(default IP 192.168.0.1):
# this can return an error, if ubi was attached before
# or rootfs part was erased before.
ubiattach -m 17
# it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs
# some devices doesn't have it
ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. download and install image via sysupgrade -n
(either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin
to the device's /tmp directory)
sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin
Sometimes it could print ubi attach error, but please ignore it
if process goes forward.
Flash Layout
NAND:
mtd8: 000a0000 00020000 "fota-flag"
mtd9: 00080000 00020000 "0:ART"
mtd10: 00080000 00020000 "mac"
mtd11: 000c0000 00020000 "reserved2"
mtd12: 00400000 00020000 "cfg-param"
mtd13: 00400000 00020000 "log"
mtd14: 000a0000 00020000 "oops"
mtd15: 00500000 00020000 "reserved3"
mtd16: 00800000 00020000 "web"
mtd17: 01d00000 00020000 "rootfs"
mtd18: 01900000 00020000 "data"
mtd19: 03200000 00020000 "fota"
mtd20: 0041e000 0001f000 "kernel"
mtd21: 0101b000 0001f000 "ubi_rootfs"
SPI:
mtd0: 00040000 00010000 "0:SBL1"
mtd1: 00020000 00010000 "0:MIBIB"
mtd2: 00060000 00010000 "0:QSEE"
mtd3: 00010000 00010000 "0:CDT"
mtd4: 00010000 00010000 "0:DDRPARAMS"
mtd5: 00010000 00010000 "0:APPSBLENV"
mtd6: 000c0000 00010000 "0:APPSBL"
mtd7: 00050000 00010000 "0:reserved1"
Back to Stock (!!! need original dump taken from initramfs !!!)
-------------
1. Place mtd16.bin and mtd17.bin initramfs image
for the device on a TFTP in the server's root.
This example uses Server IP: 192.168.0.2
2. Connect serial console (115200,8n1) to serial console
connector (refer to the pin-out from above).
3. Connect TFTP server to RJ-45 port (WAN/LAN1).
4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s
5. Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase RootFS+Web:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000
This will restore RootFS:
tftpboot 0x84000000 ${dir}root_uImage_s
nand erase 0x1800000 0x1D00000
nand write $fileaddr 0x1800000 $filesize
This will restore Web Interface:
tftpboot 0x84000000 ${dir}web.img
nand erase 0x1000000 0x800000
nand write $fileaddr 0x1000000 $filesize
After first boot on stock firwmare, do a factory reset.
Push reset button for 5 seconds so all parameters will
be reverted to the one printed on label on bottom of the router
Signed-off-by: Giammarco Marzano <stich86@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
(Warning: commit message did not conform to UTF-8 - hopefully fixed?,
added description of the pin-out if image goes down, reformatted
commit message to be hopefully somewhat readable on git-web,
redid some of the gpio-buttons & leds DT nodes, etc.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac
(WiFi-5) wireless function, based on IPQ4019.
Specification:
- SoC : Qualcomm IPQ4019
- RAM : DDR3 512 MiB (H5TC4G63EFR)
- Flash : eMMC 4 GiB (THGBMNG5D1LBAIT)
- WLAN : 2.4/5 GHz 2T2R (IPQ4019)
- Ethernet : 10/100/1000 Mbps x2
- Transceiver : Qualcomm QCA8072
- WWAN : Telit LN940A9
- Z-Wave : Silicon Labs ZM5101
- Bluetooth : Qualcomm CSR8811
- Audio DAC : Realtek ALC5629
- Audio Amp. : Realtek ALC1304
- Voice Input Processor : Conexant CX20924
- Micro Controller Unit : Nuvoton MINI54FDE
- RGB LED, Fan, Temp. sensors
- Touch Sensor : Cypress CY8C4014LQI
- RGB LED driver : TI LP55231 (2x)
- LEDs/Keys : 11x, 6x
- UART : through-hole on PCB
- J1: 3.3V, TX, RX, GND from tri-angle marking
- 115200n8
- Power : 12 VDC, 2.5 A
Flash instruction using initramfs image:
1. Prepare TFTP server with the IP address 192.168.132.100 and place the
initramfs image to TFTP directory with the name "C0A88401.img"
2. Boot NCP-HG100/Cellular and interrupt after the message
"Hit any key to stop autoboot: 2"
3. Perform the following commands and set bootcmd to allow booting from
eMMC
setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000"
saveenv
4. Perform the following command to load/boot the OpenWrt initramfs image
tftpboot && bootm
5. On the initramfs image, perform sysupgrade with the sysupgrade image
(if needed, backup eMMC partitions by dd command and download to
other place before performing sysupgrade)
6. Wait for ~120 seconds to complete flashing
Known issues:
- There are no drivers for audio-related chips/functions in Linux Kernel
and OpenWrt, they cannot be used.
- There is no driver for MINI54FDE Micro-Controller Unit, customized for
this device by the firmware in the MCU. This chip controls the
following functions, but they cannot be controlled in OpenWrt.
- RGB LED
- Fan
this fan is controlled automatically by MCU by default, without
driver
- Thermal Sensors (2x)
- Currently, there is no driver or tool for CY8C4014LQI and cannot be
controlled. It cannot be exited from "booting mode" and moved to "normal
op mode" after booting. And also, the 4x buttons (mic mute, vol down,
vol up, alexa trigger) connected to the IC cannot be controlled.
- it can be exited from "booting mode" by installing and executing
i2cset command:
opkg update
opkg install i2c-tools
i2cset -y 1 0x14 0xf 1
- There is a connection issue on the control by uqmi for the WWAN module.
But modemmanager can be used without any issues and the use of it is
recommended.
- With the F2FS format, too many errors are reported on erasing eMMC
partition "rootfs_data" while booting:
[ 1.360270] sdhci: Secure Digital Host Controller Interface driver
[ 1.363636] sdhci: Copyright(c) Pierre Ossman
[ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO
...
[ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[ 1.528325] mmc0: new HS200 MMC card at address 0001
[ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB
[ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB
[ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB
[ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0)
[ 1.550323] Alternate GPT is invalid, using primary GPT.
[ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17
...
[ 8.841400] mount_root: loading kmods from internal overlay
[ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 9.240465] block: attempting to load /etc/config/fstab
[ 9.246722] block: unable to load configuration (fstab: Entry not found)
[ 9.246863] block: no usable configuration
[ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet
[ 9.438915] urandom_read: 5 callbacks suppressed
[ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read)
[ 12.243332] mmc_erase: erase error -110, status 0x800
[ 12.246638] mmc0: cache flush error -110
[ 15.134585] mmc_erase: erase error -110, status 0x800
[ 15.135891] mmc_erase: group start error -110, status 0x0
[ 15.139850] mmc_erase: group start error -110, status 0x0
...(too many the same errors)...
[ 17.350811] mmc_erase: group start error -110, status 0x0
[ 17.356197] mmc_erase: group start error -110, status 0x0
[ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00
[ 17.446910] mmc0: tuning execution failed: -5
[ 17.447111] mmc0: cache flush error -110
[ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint
[ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b
[ 18.198691] block: attempting to load /etc/config/fstab
[ 18.198972] block: unable to load configuration (fstab: Entry not found)
[ 18.203029] block: no usable configuration
[ 18.211371] mount_root: overlay filesystem has not been fully initialized yet
[ 18.214487] mount_root: switching to f2fs overlay
So, this support uses ext4 format instead which has no errors.
Note:
- The primary uart is shared for debug console and Z-Wave chip. The
function is switched by GPIO15 (Linux: 427).
value:
1: debug console
0: Z-Wave
- NCP-HG100/Cellular has 2x os-image pairs in eMMC.
- 0:HLOS, rootfs
- 0:HLOS_1, rootfs_1
In OpenWrt, the first image pair is used.
- "bootipq" command in U-Boot requires authentication with signed-image
by default. To boot unsigned image of OpenWrt, use "mmc read" and
"bootm" command instead.
- This support is for "Cellular" variant of NCP-HG100 and not tested on
"WLAN" (non-cellular) variant.
- The board files of ipq-wifi may also be used in "WLAN" variant of
NCP-HG100, but unconfirmed and add files as for "Cellular" variant.
- "NET" LED is used to indicate WWAN status in stock firmware.
- There is no MAC address information in the label on the case, use the
address included in UUID in the label as "label-MAC" instead.
- The "CLOUD" LEDs are partially used for indication of system status in
stock firmware, use they as status LEDs in OpenWrt instead of RGB LED
connected to the MCU.
MAC addresses:
LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex))
WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex))
2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex))
5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex))
partition layout in eMMC (by fdisk, GPT):
Disk /dev/mmcblk0: 7733248 sectors, 3776M
Logical sector size: 512
Disk identifier (GUID): ****
Partition table holds up to 20 entries
First usable sector is 34, last usable sector is 7634910
Number Start (sector) End (sector) Size Name
1 34 1057 512K 0:SBL1
2 1058 2081 512K 0:BOOTCONFIG
3 2082 3105 512K 0:QSEE
4 3106 4129 512K 0:QSEE_1
5 4130 4641 256K 0:CDT
6 4642 5153 256K 0:CDT_1
7 5154 6177 512K 0:BOOTCONFIG1
8 6178 6689 256K 0:APPSBLENV
9 6690 8737 1024K 0:APPSBL
10 8738 10785 1024K 0:APPSBL_1
11 10786 11297 256K 0:ART
12 11298 11809 256K 0:HSEE
13 11810 28193 8192K 0:HLOS
14 28194 44577 8192K 0:HLOS_1
15 44578 306721 128M rootfs
16 306722 568865 128M rootfs_1
17 568866 3958065 1654M rootfs_data
[initial work]
Signed-off-by: Iwao Yuki <dev.clef@gmail.com>
Co-developed-by: Iwao Yuki <dev.clef@gmail.com>
[adjustments, cleanups, commit message, sending patch]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
(dropped clk_unused_ignore, dropped 901-* patches, renamed
key nodes, changed LEDs chan/labels to match func-en, made
:net -> (w)wan leds)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fix this occurrence during boot:
/bin/board_detect: line 10: Unsupported: not found
Fixes: 80baffd2aa (" ipq40xx: add support for Pakedge WR-1")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
On OEM firmware both addresses for In and Out ports are different. Set
them as such also in OpenWrt.
Fixes: e24635710c (" ipq40xx: add support for Luma Home WRTQ-329ACN")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
use the toolchain's default CPU (464fp) as the CPU option.
This fixes a CPU selection prompt which shows up now.
CPU selection
> 1. Generic 32 bits powerpc (POWERPC_CPU) (NEW)
2. Rely on the toolchain's implicit default CPU (TOOLCHAIN_DEFAULT_CPU) (NEW)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the 5.10 uml build currently breaks with:
/usr/bin/ld: arch/um/os-Linux/signal.o: in function `sigusr1_handler':
arch/um/os-Linux/signal.c:141: undefined reference to `uml_pm_wake'
But there's an upstream fix for this. Backport the fix
for now but also let upstream know so it finds its way
through the -stable releases.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds some missing IOMMU related options for x86/64 and moves some
of them to generic for all targets.
On x86 IOMMU_DEFAULT_DMA_LAZY is used by default, on all other platforms
IOMMU_DEFAULT_DMA_STRICT is the default. we just follow the default
kernel configuration here.
Fixes: 8fea4a102c ("x86/64: enable IOMMU support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The 5.15 kernel has new interesting features like MGLRU. Most of the
targets already have added support for testing kernel 5.15 since April
2022. Set 5.15 as default for all subtargets.
Testing support was added here:
- ae6bfb7d67 ("ath79: tiny: add 5.15 support for tiny subtarget")
- 9a0155bc4f ("ath79: add 5.15 support for generic subtarget")
- 5af9aafabb ("ath79: mikrotik: add 5.15 support for mikrotik subtarget")
- f3fa68e515 ("ath79: nand: add 5.15 support for nand subtarget")
Tested on:
- Nanostation M5 XM (tiny)
- TP-Link EAP-225 Outdoor (generic)
- TP-Link CPE210 (generic)
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fixes situations where MAC address gets incremented multiple times
if device initialization fails at first and then is deferred.
Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Will Moss <willormos@gmail.com>
When building OpenWrt with CONFIG_ALL_KMODS the kernel build will ask
for CONFIG_DEFAULT_FQ_PIE option. This deactivates it by default.
Fixes: c3e4a0d99b ("kernel: netsupport: Add FQ-PIE as an optional sched kmod and extract PIE")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable IOMMU support for Intel and AMD x86 platforms. With this, when the
vfio module is present, physical PCI devices can be passed to VMs, for
example with `qemu-system-x86_64 -device vfio-pci,host=05:00.0 ...`.
IOMMU support increases the kernel size by a small amount (~370KB, from
5239840 B to 5611200 B, a ~7% increase in size).
Signed-off-by: Nicola Corna <nicola@corna.info>
Broadcom's U-Boot contains environment data blocks. They need to be
found (offsets aren't predefined) to access env variables.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
With the commit 5876d6a62f the command under
`/usr/sbin/grub-bios-setup` has been moved to its own package named
`grub-bios-setup`.
The script `81_upgrade_bootloader` under `/lib/preinit` is used by all
x86 targets to update the bootloader. The script is using the command
`grub-bios-setup` for this.
I get the following output at the first boot after the upgrade.
`/etc/preinit: line 9: /usr/sbin/grub-bios-setup: not found`.
To fix this, the DEFAULT_PACKAGES dependency is extended by the entry
`grub2-bios-setup` so that the missing command is installed again.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Backport upstream code split patch for qca8k needed for ipq40xx target
to correctly implement a DSA driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently we fix interrupts/timers for the secondary CPU by patching
vsmp_init_secondary(). Get a little bit more generic and use the
upstream recommended way instead. Additionally avoid a check around
register_cps_smp_ops() because it does that itself.
See https://lkml.org/lkml/2022/9/12/522
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The interrupt controller depends on two control registers. GIMR enables
or disables interrupts and IRRx routes these to MIPS CPU interrupts 2-7.
Wiki currently states "A value of '0' (in IRRx) disconnects this input from
the output line, independent of the line's setting in GIMR."
Contrary to normal intuition this statement DOES NOT mean, that interrupts
can be disabled by IRRx alone. The sad truth was discovered by enabling
SMP for an Zyxel XGS1010 on the 930x target. It shows that driver and
interrupts behave as follows:
- Timer 0 interrupt 7 has active routing to CPU0 and no routing to CPU1
- Timer 1 interrupt 8 has no routing to CPU0 and active routing to CPU1
- Unmasking (enabling) interrupts writes 1 bits to all GIMR registers
- Masking (disabling) interrupts writes 0 bits to both GIMR registers
During operation we can encounter a situation like
- GIMR bit for a interrupt/CPU combination is set to enabed (=1)
- IRRx routing bits for a interrupt/CPU combination are set to disabed (=0)
This setting already allows the hardware to fire interrupts to the target
CPU/VPE if the other CPU/VPE is currently busy. Especially for CPU bound
timer interrupts this is lethal. If timer interrupt 7 arrives at CPU1 and
vice versa for interrupt 8 the restart trigger gets lost. The timer dies
and a msleep() operation in the kernel will halt endlessly.
Fix this by tracking the IRRx active routing setting in a new bitfield with
0="routing active" and 1="no routing". Enable interrupts in GIMR only
for a interrupt & CPU if routing is active. Thus we have
- GIMR = 0 / IRRx = 0 -> everything disabled
- GIMR = 1 / IRRx > 0 -> active and normal routing
- GIMR = 0 / IRRx > 0 -> masked (disabled) with normal routing
- GIMR = 1 / IRRx = 0 -> no longer possible
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
The image builds for Linksys EA6350 v3, EA8300, and MR8300 currently
fail on buildbots due to the KERNEL_SIZE, as stated in commit
17b7756b5a ("ipq40xx: 5.15: add testing kernel version"). Disable
these boards for now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Add the missing LEDs for GB-PC2. Some of these LEDs don't exist on the
device schematics. Tests on a GB-PC2 by me and Petr proved otherwise.
Remove ethblack-green and ethblue-green LEDs for GB-PC1. They are not wired
to GPIO 3 or 4 and the wiring is currently unknown.
Set ethyellow-orange to display link state and activity of the ethyellow
interface for GB-PC2.
Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The Build prefix is used for image build commands, while the Device
prefix should be used for base recipes for devices. Apply the same
naming convention here.
While touching the file, also fix the mixed indentation.
Suggested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
There seems to be no reason to have the Netgear switches as part of
the main Makefile. Move it to its subtarget-specific Makefile since
it is only applicable there.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[update commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Currently supported HPE 1920 devices all have an RTL838x SoC, but there
are larger switches with RTL839x SoCs, although currently not supported.
Move the build recipe to common.mk so the larger devices can also make
use of the recipe, while moving it out of the main Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The D-Link DGS-1210 device series currently has supported devices with
both RTL838x and RTL839x SoCs. An image build recipe has been defined in
both subtarget makefiles, but these are mostly identical, save for the
SOC variable.
Move the SOC variable from the DGS-1210 build recipes to the applicable
devices, and put the remaining duplicate code in a shared Makefile.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Hardware specification
----------------------
* RTL8393M SoC, 1 MIPS 34Kc core @ 700MHz
* 128MB DRAM
* 32MB NOR Flash
* 48 x 10/100/1000BASE-T ports
- 6 x External PHY with 8 ports (RTL8218D)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J14
The gpio-restart node is not required but it does reset the switch.
TODO: The 4 combo ports attached to the RTL8214FC are not detect
properly. Linux kernel reports 49 and 50 as "External RTL8393 SERDES"
and 51 and 52 as "RTL8218B (external)". Those ports only work if
u-boot initialize it (for example, loading initramfs image using one
of those ports). A patch to PHY detection is needed for full support.
The firmware recovery using U-Boot is broken for all DGS-1210 tested
devices as pressing RESET does not trigger it (only if pressed from a
running stock image)
UART pinout
-----------
[o]ooo|J14
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Installation using OEM upgrade
------------------------------
1. Make sure you are running OEM firmware in image2 slot (logged as admin):
- > config firmware image_id 2 boot_up
- > reboot
2. Install squashfs-factory_image1.bin to image1 using (logged as admin):
- > download firmware_fromTFTP <tftpserver> factory_image1.bin
- > config firmware image_id 1 boot_up
- > reboot
Installation using serial interface
-----------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl839x-d-link_dgs-1210-52-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
Once booted the initramfs, install the squashfs-sysupgrade.bin as a
normal OpenWrt system.
Dual-boot with stock firmware using writable u-boot-env
-------------------------------------------------------
From stock to OpenWrt / boot image 1 (CLI as admin):
- > config firmware image_id 1 boot_up
- > reboot
From OpenWrt to stock / boot image 2: (shell as root)
- # fw_setenv bootcmd 'run addargs ; bootm 0xb4e80000'
- # fw_setenv image '/dev/mtdblock7'
- # reboot
Debrick using serial interface
------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
Back to stock firmware using dual-boot
--------------------------------------
If you have serial interface, you can change u-boot env vars
interrupting the boot process. If not but you are running OpenWrt, you
can dual-boot (as mentioned eariler) and skip to step 4:
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Boot the image 2:
- set image /dev/mtdblock7; run addargs; bootm 0xb4e80000
4. Once booted, log as admin and change the boot image to 2
- > config firmware image_id 2 boot_up
- > reboot
5. After the boot, flash image1 with the vendor image
Back to stock firmware using DNA
--------------------------------
1. From an OpenWrt:
- # fw_setenv bootstop on
- # reboot
2. In a Windows PC, run 'D-Link Network Assistant v2.0.2.4'. It should
detect the switch
3. Flash the firmware.
It has been developed and tested on device with F3 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
The D-Link DGS device tree was reorganized to better reflect the common
DT parts. The common include is named SOC specific (838X) and it seemed
like a good choice to add another common include in the future for the
RTL839X devices. From the current point of view this option is not really
needed.
1. The common part only includes data that matches RTL839X devices too.
2. The Panasonic DT structure avoids including the basic DTSI inside the
common DTSI.
Taking simplicity of the Panasonic include logic and in perparation to
provide DGS-1210-52 support it makes sense to harmonize this.
- rename common include to reflect its content
- move the link to the root DTSI directly to the device specific DTS
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Otherwise kernel 5.15 will fail to build on subtargets except for mt7621
that has enabled the config.
The disabled PINCTRL_AW9523 config disappears after a refresh, it needs
to be added back manually.
Fixes: 675cf75578 ("ramips: add config-5.15 for mt7620 subtarget")
Fixes: 001176994a ("ramips: add config-5.15 for mt76x8 subtarget")
Fixes: b9d9f33c33 ("ramips: add config-5.15 for rt288x subtarget")
Fixes: 0164dc0c25 ("ramips: add config-5.15 for rt305x subtarget")
Fixes: ef59da8669 ("ramips: add config-5.15 for rt3883 subtarget")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently factory.bin image recipe of ASUS RP-AC51 is not specified
explicitly and is thus set to the leaked one from the device recipe
right above, i.e. ASUS PL-AC56. Fix it to avoid potential breakage.
Fixes: 416d4483e8 ("ath79: add support for ASUS RP-AC51")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This patch will print the name of the modem in the bootlog
during probing.
This allows to verify that the exact model was loaded and not some
generic type.
The only other way to do this is by enabling dynamic debugging
which is disabled by default in OpenWRT
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Due to an oversight we accidentally inverted the timeout check. This
patch corrects this.
Fixes: 9cec4a0ea4 ("realtek: Use built-in functionality for timeout loop")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[ wrap poll_timeout line to 80 char ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- refresh config
- disable suspend as it's pointless in the sope of OpenWrt
- enable CPU frequency scaling
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
In commit 81e3017609 ("realtek: clean up rtl838x MDIO busy wait loop")
a hand-crafted loop was created, that nearly exactly replicate the
iopoll's `read_poll_timeout` functionality.
Use that instead.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
When converting this device to use both GMACs, I mistakenly removed
state_default, which prevented GPIO LEDs and keys from being used.
Fixes: f4eef5f2a1 ("ramips: add support for Linksys E7350")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When converting this device to use both GMACs, I mistakenly removed
state_default, which prevented GPIO LEDs and keys from being used.
Add back and and extra LEDs that were missing.
Tested all LEDs by turning them on.
Fixes: 26a6a6a60b ("ramips: add support for Belkin RT1800")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.
This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.
Specifications:
---------------
- SoC: Realtek RTL8380M
- Flash: 32 MiB SPI flash (Vendor varies)
- RAM: 256 MiB (Vendor varies)
- Ethernet: 8x 10/100/1000 Mbps with PoE (all ports)
2x SFP ports
- Buttons: 1x "Reset" button on front panel
- Power: 53.5V DC barrel jack
- UART: 1x serial header, unpopulated
- PoE: 2x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- (2) SFP ports (with caveats)
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE LEDs
Enabling SFP ports:
-------------------
The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.
However, to enable the lasers on SFP1 and SFP2 respectively:
echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWrt.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The "firmware" partition was assembled from two contiguous partitions.
This complexity is unnecessary. Instead of using mtd-concat over
"sys" and "usrimg1", simply declare the "firmware" partition to cover
the flash space instead.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The TP-Link RTL83xx based switches have their MAC address programmed
in the "para" partition. While in theory, the format of this partition
is dynamic, in practice, the MAC address appears to be located at a
consistent address. Thus, use nvmem-cells to read this MAC address.
The main MAC is required for deriving the MAC address of the switch
ports. Instead of reading it via mtd_get_mac_binary(), alias the
ethernet0 node as the label-mac-device, and use get_mac_label().
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Although PHY nodes are labeled, the port nodes were not. Labeling of
ports is useful for 'status = "disabled"' ports, which is supported
since commit 9a7f17e11f ("realtek: ignore disabled switch ports")
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The TP-Link TL-SG2008, TL-SG2008P, and TL-SG2210P use the same board.
The main difference is that some footprints are not populated in the
lower-end models. To model this with minimal duplication, move the
devicetree to a common dtsi, leaving out just the board name.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[remove port relabelling from commit message, already merged with commit
18a2b29aa1 ("realtek: tl-sg2008p: fix labeling of lan ports")]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
When we use the internal toolchain USE_SSTRIP will be selected by
default for musl libc and USE_STRIP when glibc is used. Do the same when
an external toolchain is used. USE_GLIBC will also be set for external
toolchain builds based on the EXTERNAL_TOOLCHAIN_LIBC_USE_GLIBC setting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specification:
SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
3x 10/100 Mbps Ethernet (2x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: Yes
8x LED, 2x button
Flash instruction:
Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-4g-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Sergei Burakov <senior.anonymous@mail.ru>
The newly introduced config symbol CONFIG_CMDLINE_OVERRIDE is only set
for mt7629 for now which breaks automated build on all other mediatek
subtargets. Make sure the symbol is configured as 'is not set' for all
remaining subtargets.
Fixes: c27279dc26 ("mediatek: add support for ipTIME A6004MX Add basic support for ipTIME A6004MX.")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
Support devices that has vendor custom header before FIT image.
Some devices has vendor custom header before FIT image. In this case mtd-
split can not find FIT image and it results in rootfs mount failure.
Please refer iptime,a6004mx device for further examples.
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
MT7915 requires an additional antenna for background radar scanning.
Disable this feature in the following devices that do not have a
separate DFS antenna:
linksys,e8450
ruijie,rg-ew3200gx-pro
xiaomi,redmi-router-ax6s
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Background radar detection is not supported on devices that
using MT7905, so disable this feature in the following devices:
asus,rt-ax53u
jcg,q20
tplink,eap615-wall-v1
xiaomi,mi-router-cr6606
xiaomi,mi-router-cr6608
xiaomi,mi-router-cr6609
yuncore,ax820
Devices with MT7915 lacking a DFS antenna also do not support
background DFS:
totolink,x5000r
cudy,x6
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The patch adding support for LEDs connected to a reset controller did
not apply any more, refresh it on top of current master.
Fixes: 53fc987b25 ("generic: move ledbar driver from mediatek target")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: ar9341
- RAM: 32M
- Flash: 4M
- Ethernet: 5x FE ports
- WiFi: ar9341-wmac
Flash instruction:
Upload generated factory firmware on vendor's web interface.
This device is very similar to the TL-WR841N v8, only two LED GPIOs are
different.
Buttons configuration is similar to TL-WR842ND v2 but both buttons are
active low.
Signed-off-by: Will Moss <willormos@gmail.com>
Add support for TP-Link Deco S4 wifi router
The label refers to the device as S4R and the TP-Link firmware
site calls it the Deco S4 v2. (There does not appear to be a v1)
Hardware (and FCC id) are identical to the Deco M4R v2 but the
flash layout is ordered differently and the OEM firmware encrypts
some config parameters (including the label mac address) in flash
In order to set the encrypted mac address, the wlan's caldata
node is removed from the DTS so the mac can be decrypted with
the help of the uencrypt tool and patched into the wlan fw
via hotplug
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
UART serial access (115200N1) on board via solder pads:
RX = TP1 pad
TX = TP2 pad
GND = C201 (pad nearest board edge)
The device's bootloader and web gui will only accept images that
were signed using TP-Link's RSA key, however a memory safety bug
in the bootloader can be leveraged to install openwrt without
accessing the serial console. See developer forum S4 support page
for link to a "firmware" file that starts a tftp client, or you
may generate one on your own like this:
```
python - > deco_s4_faux_fw_tftp.bin <<EOF
import sys
from struct import pack
b = pack('>I', 0x00008000) + b'X'*16 + b"fw-type:" \
+ b'x'*256 + b"S000S001S002" + pack('>I', 0x80060200) \
b += b"\x00"*(0x200-len(b)) \
+ pack(">33I", *[0x3c0887fc, 0x35083ddc, 0xad000000, 0x24050000,
0x3c048006, 0x348402a0, 0x3c1987f9, 0x373947f4,
0x0320f809, 0x00000000, 0x24050000, 0x3c048006,
0x348402d0, 0x3c1987f9, 0x373947f4, 0x0320f809,
0x00000000, 0x24050000, 0x3c048006, 0x34840300,
0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000,
0x24050000, 0x3c048006, 0x34840400, 0x3c1987f9,
0x373947f4, 0x0320f809, 0x00000000, 0x1000fff1,
0x00000000])
b += b"\xff"*(0x2A0-len(b)) + b"setenv serverip 192.168.0.2\x00"
b += b"\xff"*(0x2D0-len(b)) + b"setenv ipaddr 192.168.0.1\x00"
b += b"\xff"*(0x300-len(b)) + b"tftpboot 0x81000000 initramfs-kernel.bin\x00"
b += b"\xff"*(0x400-len(b)) + b"bootm 0x81000000\x00"
b += b"\xff"*(0x8000-len(b))
sys.stdout.buffer.write(b)
EOF
```
Installation:
1. Run tftp server on pc with static ip 192.168.0.2
2. Place openwrt "initramfs-kernel.bin" image in tftp root dir
3. Connect pc to router ethernet port1
4. While holding in reset button on bottom of router, power on router
5. From pc access router webgui at http://192.168.0.1
6. Upload deco_s4_faux_fw_tftp.bin
7. Router will load and execture in-memory openwrt
8. Switch pc back to dhcp or static 192.168.1.x
9. Flash openwrt sysupgrade image via luci/ssh at 192.168.1.1
Revert to stock:
Press and hold reset button while powering device to start the
bootloader's recovery mode, where stock firmware can be uploaded
via web gui at 192.168.0.1
Please note that one additional non-github commits is also needed:
firmware-utils: add tplink-safeloader support for Deco S4
Signed-off-by: Nick French <nickfrench@gmail.com>
FCC ID: U2M-CAP2100AG
WatchGuard AP100 is an indoor wireless access point with
1 Gb ethernet port, dual-band but single-radio wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP300 v2
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 2 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:e5 art 0x0 -2
phy0 ---- *:e5 art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-CAP4200AG
WatchGuard AP200 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP600
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI card 168c:0030, 5 GHz, 2x2, 26dBm
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 4 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:be art 0x0 -2
phy1 ---- *:bf art 0x0 -1
phy0 ---- *:be art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Tested-by: John Delaney <johnd@ankco.net>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: Q6G-AP300
WatchGuard AP300 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card 168c:003c, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 32 MB FLASH S25FL512S
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 6 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:3c art 0x0
phy1 ---- *:3d ---
phy0 ---- *:3e ---
**Serial console access:**
For this board, its not certain whether UART is possible
it is likely that software is blocking console access
the RX line on the board for UART is shorted to ground by resistor R176
the resistors R175 and R176 are next to the UART RX pin at J10
however console output is garbage even after this fix
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell access
downgrade XTM firewall to v2.0.0.1
downgrade AP300 firmware: v1.0.1
remove / unpair AP from controller
perform factory reset with reset button
connect ethernet to a computer
login to OEM webpage with default address / pass: wgwap
enable SSHD in OEM webpage settings
access root shell with SSH as user 'root'
modify uboot environment to automatically try TFTP at boot time
(see command below)
rename initramfs-kernel.bin to test.bin
load test.bin over TFTP (see TFTP recovery)
(optionally backup all mtdblocks to have flash backup)
perform a sysupgrade with sysupgrade.bin
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
server ip: 192.168.1.101
reset button seems to do nothing at boot time...
only possible with modified uboot environment,
running this command in the root shell:
fw_setenv bootcmd 'if ping 192.168.1.101; then tftp 0x82000000 test.bin && bootm 0x82000000; else bootm 0x9f0a0000; fi'
and verify that it is correct with
fw_printenv
then, before boot, the device will attempt TFTP from 192.168.1.101
looking for file 'test.bin'
to return uboot environment to normal:
fw_setenv bootcmd 'bootm 0x9f0a0000'
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM
(see installation method 2)
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Alessandro Kornowski <ak@wski.org>
Tested-by: John Wagner <john@wagner.us.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
after some trial and error, it was discovered
that by setting TX only delay on the AR8035 PHY
that setting GMAC registers is no longer necessary.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
