Commit Graph

20202 Commits

Author SHA1 Message Date
Aviana Cruz
144fa4d4e7 netfilter: add kmod-nf-conntrack
There have been some demands for the `ct count` expression,
like https://forum.openwrt.org/t/22-03-2-unable-to-use-ct-count-nft-rules/146680.

This adds the required kernel modules for the expression to work.

Signed-off-by: Aviana Cruz <gwencroft@proton.me>
2023-02-18 17:12:30 +01:00
Michael Pratt
4ef86c620f ramips: add support for Senao Engenius EPG600
FCC ID: A8J-EPG600

Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)

this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.

**Specification:**

  - MT7620 SOC		MIPS 24kec, 2.4 GHz WMAC, 2x2
  - RT5592N WLAN	PCI chip, 5 GHz, 2x2
  - QCA8337N Gb SW	RGMII GbE, SW P0 -- SOC P5, 5 LEDs
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 64 MB RAM		NT5TU32M16
  - UART console	J2, populated
  - USB 2.0 port	direct to SOC
  - 6 GPIO LEDs		power, 2G, 5G, wps2g, wps5g, line
  - 3 buttons		reset, wps, "reg" (registeration)
  - 4 antennas		internal omni-directional plates

NOT YET SUPPORTED: VoIP

  - Si3050-FT + Si3019-FT	Voice DAA, SPI control, PCM data
  - Phone Ports "TEL", "LINE"	RJ11, 4P2C (2 pins)

**MAC addresses:**

  MAC address labeled as MAC ADDRESS
  MACs present in both wifi cal data and uboot environment

  eth0.1/phy1	----	*:82	rf 0x4
  phy0		----	*:83	factory 0x4
  eth0.2	MAC	*:b8	"wanaddr"

**Installation:**

  Method 1: Firmware upgrade page:

    (if you cannot access the APs webpage)
    factory reset with the reset button
    connect ethernet to a computer
    OEM webpage at 192.168.0.1
    username and password 'admin'

    Navigate to gear icon, "Device Management", "Tools"
    select the factory.dlf image
    Upload and verify checksum

  Method 2: Serial to upload initramfs:

    Follow directions for TFTP recovery
    upload and boot initramfs and do a sysupgrade

**TFTP recovery:**

  Requires UART serial console, reset button does nothing

  rename initramfs-kernel.bin to 'uImageEPG600'
  make available on TFTP server at 192.168.99.8
  power board, interrupt boot with "4"
  execute `tftpboot` and `bootm` (with the load address)

**Return to OEM:**

  Images from OEM are provided, but not compatible
  with openwrt sysupgrade. So it must be modified.

  Alternatively, back up all mtd partitions before flashing

**Note on switch registers:**

  The necessary registers needed for the QCA8337 switch
  can be read from interrupted boot (tftpboot, bootm)
  by using the following lines in the switch driver ar8327.c
  in the function 'ar8327_hw_config_of'
  where 'qca,ar8327-initvals' is parsed from DTS
  before the new register values are written:

    pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
    pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
    pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
    pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-02-18 16:55:35 +01:00
Yuu Toriyama
1173edf23b wireless-regdb: update to 2023.02.13
Changes:
  7f7a9f7 wireless-regdb: update regulatory database based on preceding changes
  660a1ae wireless-regdb: Update regulatory info for Russia (RU) on 5GHz
  fe05cc9 wireless-regdb: Update regulatory rules for Japan (JP) on 6GHz
  d8584dc wireless-regdb: Update regulatory rules for Japan (JP) on 5GHz
  c04fd9b wireless-regdb: update regulatory rules for Switzerland (CH)
  f29772a wireless-regdb: Update regulatory rules for Brazil (BR)

Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
2023-02-18 16:27:37 +01:00
Stijn Tintel
65c9b5ffb0 odhcpd: bump to git HEAD
dfab0fa dhcpv4: detect noarp interfaces
  5a17751 router: improve RA logging
  edc5e17 router: always check ra_default

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2023-02-17 16:30:03 +02:00
Stijn Tintel
baf76634f3 build: add option to use preinit IP as LAN IP
We currently have build options to customize the IP address used in the
preinit phase of the boot process, but not to set the default LAN IP.

Introduce a boolean build option that, when enabled, results in the IP
address configured for the preinit phase, to be also used as the default
LAN IP address.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2023-02-17 16:20:03 +02:00
Robert Marko
061e863bae
kernel: modules: package Aquantia PHY driver
Package the Aquantia AQR PHY driver as kmod.

This enables using the Aquantia driver with hwmon support on targets where
hwmon is not compiled-in.

Currently, in case when AQR driver is compiled-in but hwmon core is not
hwmon code in AQR driver will not get compiled because of macro
IS_REACHABLE(CONFIG_HWMON) evaluating to false.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-02-15 23:28:57 +01:00
Rafał Miłecki
3c66ac7e22 iptables: iptables-mod-conntrack-extra: don't select kmod-ipt-raw
Package kmod-ipt-raw enables CONFIG_IP_NF_RAW and packages
iptable_raw.ko

According to kernel's net/netfilter/Kconfig there are only 3 kernel
symbols that depend on the IP_NF_RAW:
1. NETFILTER_XT_TARGET_CT (xt_CT.ko)
2. NETFILTER_XT_TARGET_NOTRACK (unused symbol?!)
3. NETFILTER_XT_TARGET_TRACE (xt_TRACE.ko)

Now: iptables-mod-conntrack-extra selects kmod-ipt-conntrack-extra which
provides: xt_helper.ko nf_conncount.ko xt_connlimit.ko xt_connmark.ko
xt_recent.ko and xt_connbytes.ko (none of them seems to require
iptable_raw.ko).

It seems there is no explicit reason for iptables-mod-conntrack-extra to
require kmod-ipt-raw (iptables_raw.ko).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-15 14:28:08 +01:00
Rafał Miłecki
601257e388 netifd: refactor packet steering init
1. Move setup code to independent script file
2. Add init.d script to allow automatic updates
3. Support platform specific /usr/libexec/platform/packet-steering.sh

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-15 14:25:38 +01:00
Daniel Golle
e8625c89ef treewide: replace /sys/devices/virtual/ubi by /sys/class/ubi
Starting from Linux Kernel version 6.3 UBI devices will no longer be
considered virtual, but rather have an MTD device parent. Hence they
will no longer be listed under /sys/devices/virtual/ubi which is
used in multiple places in OpenWrt. Prepare for future kernels by
using /sys/class/ubi instead of /sys/devuces/virtual/ubi.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-15 03:27:59 +00:00
Daniel Golle
62e583ddb9 fstools: update to git HEAD
12155d3 libfstools: use class interface to iterate over ubi devices

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-02-15 03:27:35 +00:00
Felix Fietkau
ac4fae2338 ucode: update to the latest version
08c709c58187 rtnl: add support for registering an uloop based listener
599a7fb59380 Merge pull request #140 from nbd168/rtnl
c4125c516e0a nl80211: fix NL80211_ATTR_SURVEY_INFO
c43bb9d8fe8d Merge pull request #141 from dhewg/master
c1342d934b2d nl80211: add missing ucv_get() calls
9022b270683a rtnl: add missing ucv_get() calls
837cffec5a5c Merge pull request #142 from nbd168/ref-fixes
65b1f181e642 rtnl: add missing uc_vm_registry_set call
ab2f3f70257d Merge pull request #143 from nbd168/rtnl-fix

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-14 09:59:16 +01:00
INAGAKI Hiroshi
f490295bf2
ipq807x: add support for Buffalo WXR-5950AX12
Buffalo WXR-5950AX12 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ8074A.

Specification:

- SoC         : Qualcomm IPQ8074A
- RAM         : DDR3 1024 MiB (2x Nanya NT5CC256M16ER-EK)
- Flash       : RAW NAND 256 MiB (Winbond W29N02GZBIBA)
- WLAN        : 2.4/5 GHz (IPQ8074A)
- Ethernet    : 5 ports
  - WAN       : 100/1000/2500/10000 Mbps x1 (AQR113C)
  - LAN       : 100/1000/2500/10000 Mbps x1 (AQR113C),
                10/100/1000 Mbps x3 (QCA8075)
- LED/Keys    : 8x/5x
- UART        : pin header on PCB (J7)
  - assignment: 3.3V, GND, TX, RX from disc marking
  - settings  : 115200n8
- Power       : 12 VDC, 4 A

Flash instruction using initramfs image:

1. Prepare TFTP server with IP address 192.168.11.10
2. Rename OpenWrt initramfs image to "WXR-5950AX12-initramfs.uImage and
   place it to TFTP directory
3. Hold AOSS (WPS) button and power on WXR-5950AX12
4. WXR-5950AX12 downloads initramfs image from TFTP server and boots
   with it automatically
5. Upload sysupgrade image to WXR-5950AX12 and perform sysupgrade
6. Wait ~120 seconds to complete flashing

Partition layout:

0x000000000000-0x000000100000 : "0:sbl1"
0x000000100000-0x000000200000 : "0:mibib"
0x000000200000-0x000000280000 : "0:bootconfig"
0x000000280000-0x000000300000 : "0:bootconfig1"
0x000000300000-0x000000600000 : "0:qsee"
0x000000600000-0x000000900000 : "0:qsee_1"
0x000000900000-0x000000980000 : "0:devcfg"
0x000000980000-0x000000a00000 : "0:devcfg_1"
0x000000a00000-0x000000a80000 : "0:apdp"
0x000000a80000-0x000000b00000 : "0:apdp_1"
0x000000b00000-0x000000b80000 : "0:rpm"
0x000000b80000-0x000000c00000 : "0:rpm_1"
0x000000c00000-0x000000c80000 : "0:cdt"
0x000000c80000-0x000000d00000 : "0:cdt_1"
0x000000d00000-0x000000d80000 : "0:appsblenv"
0x000000d80000-0x000000e80000 : "0:appsbl"
0x000000e80000-0x000000f80000 : "0:appsbl_1"
0x000000f80000-0x000001000000 : "0:art"
0x000001000000-0x000001080000 : "0:art_1"
0x000001080000-0x000001100000 : "0:orgdata"
0x000001100000-0x000001180000 : "0:orgdata_1"
0x000001180000-0x000005180000 : "rootfs"
0x000005180000-0x000009180000 : "rootfs_recover"
0x000009180000-0x000010000000 : "user_property"

Notes:

- WXR-5950AX12 has 2x OS images on NAND flash. The 1st image is for
  normal operation and the 2nd one is for recoverying or firmware
  upgrading on stock.

- Stock U-Boot checks MD5 hashes in "fw_hash" volume in each "root*"
  partition when booting. This is just a comparation of hash strings.

  Behaviors:

  - both "fw_hash" volumes exist, hashes are rootfs == rootfs_recover
    ---> boot from rootfs

  - both "fw_hash" volumes exist, hashes are rootfs != rootfs_recover
    ---> boot from rootfs_recover

    Note: this behavior is used for firmware upgrading on stock

  - "fw_hash" volume in rootfs is missing
    ---> boot from rootfs_recover

  - "fw_hash" volume in rootfs_recover is missing
    ---> boot from rootfs

  - "fw_hash" volumes in both root* partition are missing
    ---> boot from rootfs_recover

Reverting to stock firmware:

1. Decrypt official image by buffalo-enc and remove header

   example of decryption:

   $ buffalo-enc -i wxr_5950ax12_jp_305 -o wxr_5950ax12_jp_305.dec \
                 -d -k olaffuB -O 0xc8

   example of removing header (v3.05):

   - before

   $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.dec
   00000000  57 58 52 2d 35 39 35 30  41 58 31 32 5f 33 2e 30  |WXR-5950AX12_3.0|
   00000010  35 5f 31 2e 30 31 5f 4a  50 5f 6a 70 5f 71 63 61  |5_1.01_JP_jp_qca|
   00000020  0a 66 69 6c 65 6c 65 6e  3d 34 35 33 35 30 39 31  |.filelen=4535091|
   00000030  32 0a 55 42 49 23 01 00  00 00 00 00 00 00 00 00  |2.UBI#..........|
   00000040

   - after

   $ hexdump -n 64 -v -C wxr_5950ax12_jp_305.ubi
   00000000  55 42 49 23 01 00 00 00  00 00 00 00 00 00 00 00  |UBI#............|
   00000010  00 00 08 00 00 00 10 00  78 cf c4 91 00 00 00 00  |........x.......|
   00000020  00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00  |................|
   00000030  00 00 00 00 00 00 00 00  00 00 00 00 3d 2a 64 fd  |............=*d.|
   00000040

2. Boot WXR-5950AX12 with OpenWrt initramfs image

3. Upload modified stock image to WXR-5950AX12

4. Find partitions "rootfs" and "rootfs_recover"

   example:

   root@OpenWrt:/# cat /proc/mtd
   dev:    size   erasesize  name
   ...
   mtd22: 04000000 00020000 "rootfs"
   mtd23: 04000000 00020000 "rootfs_recover"
   ...

   in this case, "rootfs" is mtd22 and "rootfs_recover" is mtd23

5. Format "rootfs"/"rootfs_recover" partition with the uploaded image

   example:

   ubiformat /dev/mtd22 -f /tmp/wxr_5950ax12_jp_305.ubi
   ubiformat /dev/mtd23 -f /tmp/wxr_5950ax12_jp_305.ubi

6. Remove "rootfs"/"rootfs_data" volume from user_property partition

   example:

   . /lib/upgrade/nand.sh
   UBI=$(nand_attach_ubi user_property)
   ubirmvol /dev/$UBI -N rootfs
   ubirmvol /dev/$UBI -N rootfs_data

7. Reboot

MAC addresses:

LAN    : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text))
WAN    : 50:C4:DD:xx:xx:28 (0:APPSBLENV, ethaddr (text))
2.4 GHz: 50:C4:DD:xx:xx:30 (0:APPSBLENV, wlan0addr (text))
5 GHz  : 50:C4:DD:xx:xx:38 (0:APPSBLENV, wlan1addr (text))

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-12 01:18:39 +01:00
INAGAKI Hiroshi
54c5f33b30 uboot-envtools: add support for APRESIA ApresiaLightGS120GT-SS
This patch adds support for APRESIA ApresiaLightGS120GT-SS to
uboot-envtools.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2023-02-13 12:22:17 +01:00
Felix Fietkau
ec33a6ca2c mac80211: add fixes for receiving A-MSDU packets on mesh interfaces
The standard defines the A-MSDU header length field differently for mesh
compared to other modes. Deal with this accordingly and work around broken
implementations (e.g. ath10k, ath11k).

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-13 11:45:43 +01:00
Nick Hainke
9639ef2a5b e2fsprogs: update to 1.47.0
Release notes:
https://e2fsprogs.sourceforge.net/e2fsprogs-release.html#1.47.0

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-02-13 00:48:25 +01:00
Karl Chan
92276eef70 ramips: add support for ASUS RT-AX54
Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
        1x LAN (blue, configurable)
        1x WAN (blue, configurable)
	1x 2.4G (blue, not configurable)
	1x 5G (blue, not configurable)

Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
   Select "2. Upgrade firmware"
   Press enter when show "Run firmware after upgrading? (Y/n):"
   Select 0 for TFTP method
   Input U-Boot's IP address: 192.168.1.1
   Input TFTP server's IP address: 192.168.1.2
   Input IP netmask: 255.255.255.0
   Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"

Signed-off-by: Karl Chan <exkc@exkc.moe>
2023-02-12 18:27:45 +01:00
John Audia
4ae86b3358 openssl: bump to 1.1.1t
Removed upstreamed patch: 010-padlock.patch

Changes between 1.1.1s and 1.1.1t [7 Feb 2023]

  *) Fixed X.400 address type confusion in X.509 GeneralName.

     There is a type confusion vulnerability relating to X.400 address processing
     inside an X.509 GeneralName. X.400 addresses were parsed as an ASN1_STRING
     but subsequently interpreted by GENERAL_NAME_cmp as an ASN1_TYPE. This
     vulnerability may allow an attacker who can provide a certificate chain and
     CRL (neither of which need have a valid signature) to pass arbitrary
     pointers to a memcmp call, creating a possible read primitive, subject to
     some constraints. Refer to the advisory for more information. Thanks to
     David Benjamin for discovering this issue. (CVE-2023-0286)

     This issue has been fixed by changing the public header file definition of
     GENERAL_NAME so that x400Address reflects the implementation. It was not
     possible for any existing application to successfully use the existing
     definition; however, if any application references the x400Address field
     (e.g. in dead code), note that the type of this field has changed. There is
     no ABI change.
     [Hugo Landau]

  *) Fixed Use-after-free following BIO_new_NDEF.

     The public API function BIO_new_NDEF is a helper function used for
     streaming ASN.1 data via a BIO. It is primarily used internally to OpenSSL
     to support the SMIME, CMS and PKCS7 streaming capabilities, but may also
     be called directly by end user applications.

     The function receives a BIO from the caller, prepends a new BIO_f_asn1
     filter BIO onto the front of it to form a BIO chain, and then returns
     the new head of the BIO chain to the caller. Under certain conditions,
     for example if a CMS recipient public key is invalid, the new filter BIO
     is freed and the function returns a NULL result indicating a failure.
     However, in this case, the BIO chain is not properly cleaned up and the
     BIO passed by the caller still retains internal pointers to the previously
     freed filter BIO. If the caller then goes on to call BIO_pop() on the BIO
     then a use-after-free will occur. This will most likely result in a crash.
     (CVE-2023-0215)
     [Viktor Dukhovni, Matt Caswell]

  *) Fixed Double free after calling PEM_read_bio_ex.

     The function PEM_read_bio_ex() reads a PEM file from a BIO and parses and
     decodes the "name" (e.g. "CERTIFICATE"), any header data and the payload
     data. If the function succeeds then the "name_out", "header" and "data"
     arguments are populated with pointers to buffers containing the relevant
     decoded data. The caller is responsible for freeing those buffers. It is
     possible to construct a PEM file that results in 0 bytes of payload data.
     In this case PEM_read_bio_ex() will return a failure code but will populate
     the header argument with a pointer to a buffer that has already been freed.
     If the caller also frees this buffer then a double free will occur. This
     will most likely lead to a crash.

     The functions PEM_read_bio() and PEM_read() are simple wrappers around
     PEM_read_bio_ex() and therefore these functions are also directly affected.

     These functions are also called indirectly by a number of other OpenSSL
     functions including PEM_X509_INFO_read_bio_ex() and
     SSL_CTX_use_serverinfo_file() which are also vulnerable. Some OpenSSL
     internal uses of these functions are not vulnerable because the caller does
     not free the header argument if PEM_read_bio_ex() returns a failure code.
     (CVE-2022-4450)
     [Kurt Roeckx, Matt Caswell]

  *) Fixed Timing Oracle in RSA Decryption.

     A timing based side channel exists in the OpenSSL RSA Decryption
     implementation which could be sufficient to recover a plaintext across
     a network in a Bleichenbacher style attack. To achieve a successful
     decryption an attacker would have to be able to send a very large number
     of trial messages for decryption. The vulnerability affects all RSA padding
     modes: PKCS#1 v1.5, RSA-OEAP and RSASVE.
     (CVE-2022-4304)
     [Dmitry Belyavsky, Hubert Kario]

Signed-off-by: John Audia <therealgraysky@proton.me>
2023-02-12 00:08:29 +01:00
Xu Yiming
1a145ccb0a
kernel: kmod-fs-ntfs3: fix typo
Fix typo that mistaken the description of ntfs3 for fuse.

Signed-off-by: Xu Yiming <xuyiming.open@outlook.com>
2023-02-09 03:16:51 +01:00
Nick Hainke
b6bc924b19 e2fsprogs: update to 1.46.6
Release information:
https://e2fsprogs.sourceforge.net/e2fsprogs-release.html#1.46.6

Remove upstreamed patch:
- 004-CVE-2022-1304-libext2fs-add-sanity-check-to-extent-manipulation.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-02-08 00:14:53 +01:00
Leon M. George
67d2a7ef9e
base-files: ipcalc.sh: fix awk regex syntax
It worked fine before but gawk warns about it.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2023-02-07 21:05:58 +01:00
Leon M. George
2903924b57
base-files: ipcalc.sh: trim for statement
For gawk compatibility.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2023-02-07 21:05:57 +01:00
Leon M. George
e4bd3de1be
dnsmasq: refuse to add empty DHCP range
Use ipcalc's return value to react to invalid range specifications.
By simply ignoring the range instead of aborting with an error code,
dnsmasq should still start when there's an error (best effort).
Aborting the config generation or working with invalid range specs leaves
dnsmasq crash-looping which is the right thing to do concerning that
particular interface but it also hinders DHCP service on other interfaces
and DNS on the router itself.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2023-02-07 21:05:57 +01:00
Leon M. George
6ce9f42b98
base-files: ipcalc.sh: use shebang to invoke awk
There's hardly an shell logic in ipcalc.sh and a $* that would garble
parameter positions.
Move the awk invokation to the shebang.

A rename from "ipcalc.sh" to "ipcalc" is desirable but could prove tricky
with packages in other repositories depending on the filename.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2023-02-07 21:05:57 +01:00
Leon M. George
a40a96e54b
base-files: ipcalc.sh: fail when network is too small
It's possible to move range boundaries in a way that the start address
lies behind the end address.
Detect this condition and exit with an error message.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2023-02-07 21:05:56 +01:00
Leon M. George
4fe106afd1
base-files: ipcalc.sh: don't include own address in range
Make sure our own address doesn't lie in the calculated range.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2023-02-07 21:05:56 +01:00
Leon M. George
00a20335ba
base-files: ipcalc.sh: check for params before calculating start/end
With this patch, ipcalc only calculates range boundaries if the
corresponding parameters are supplied.

Signed-off-by: Leon M. George <leon@georgemail.eu>
2023-02-07 21:05:52 +01:00
Christian Marangi
f28a604df4
iwinfo: bump to latest git HEAD
c7eb8eb nl80211: restore iterating over all devices in nl80211_phy2ifname()

Fixes: #11902
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-06 21:36:51 +01:00
Christian Marangi
3ef655375a
fstools: bump to latest Git HEAD
14d535e partname: Correct fstools_partname_fallback_scan comparison

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-02-04 20:04:58 +01:00
Brian Norris
3cd882744d base-files: upgrade: Fix export_partdevice() quoting
$BOOTDEV_MAJOR may be empty for many of the uevents parsed in this
function. This condition thus tends to fail benignly (we just skip to
the next device), but it can really clutter the stage2 sysupgrade
stderr, since it looks like the "=" operand doesn't have an appropriate
left-hand argument.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-02-03 14:09:46 +01:00
Brian Norris
ecafdfa894 kernel: modules: add lkdtm module
Useful for debugging panic/error handling, crash logging, and more.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-02-03 13:48:11 +01:00
Jan Hoffmann
b91d7d9d78 ltq-*-app: extend ubus metrics/statistics
Expose a few additional useful values via ubus:

- Channel error counters (CRC, FEC)
- Retransmission counters (MINEFTR, LEFTRS)
- Impulse noise protection level
- Rate adaptation mode
- OLR statistics (Bitswap, SRA, SOS)
- Pilot tones
- Upstream/downstream band information

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-02-03 13:40:47 +01:00
Jan Hoffmann
723963543a ltq-vdsl-vr9: fix upstream MINEFTR
The upstream value read from the device seems to already be in bits per
second, so there is no need to multiply by 1000 again (which for typical
values causes an overflow of the 32-bit unsigned integer).

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2023-02-03 13:33:36 +01:00
Chen Minqiang
fcde517d35 wolfssl: fix build with make < 4.2
Inline the preinst.arm-ce script. Support for including was added in
make 4.2 and is not working with older make versions.

Fixes: https://github.com/openwrt/openwrt/issues/11866
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-02-03 12:18:19 +01:00
Glenn Strauss
2a691fc7f2 mbedtls: x509 crt verify SAN iPAddress
backport from
X509 crt verify SAN iPAddress
https://github.com/Mbed-TLS/mbedtls/pull/6475

addresses
curl built with mbedtls fails on https://1.1.1.1/ (IP address in SubjectAltName)
https://github.com/Mbed-TLS/mbedtls/issues/6473

filed for
mbedTLS: BADCERT_CN_MISMATCH on https://1.1.1.1 with curl+mbedtls
https://github.com/openwrt/packages/issues/19677

Signed-off-by: Glenn Strauss <gstrauss@gluelogic.com>
2023-02-03 11:27:58 +01:00
Felix Fietkau
acd8e94d20 mt76: update PKG_SOURCE_HASH
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-02 11:37:48 +01:00
Felix Fietkau
ff4c872c7c mt76: fix typo in PKG_SOURCE_DATE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-02 11:36:50 +01:00
Felix Fietkau
521efb62eb mt76: update to the latest version, import WED related mtk_eth_soc patches
6c256218e59e wifi: mt76: dma: use napi_build_skb
679254c50f27 mt7915: add CONFIG_MT76_LEDS to cflags
15b9dd6b1b6a wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work
8e5c21fe7c5c wifi: mt76: mt7915: rework mt7915_mcu_set_thermal_throttling
87cb74fe42d9 wifi: mt76: mt7915: rework mt7915_thermal_temp_store()
c6f24b83eba5 wifi: mt76: mt7915: add error message in mt7915_thermal_set_cur_throttle_state()
99e96b89ee4d wifi: mt76: mt7915: add chip id condition in mt7915_check_eeprom()
833cd420480f wifi: mt76: mt7921: fix channel switch fail in monitor mode
f1f8bae6092d wifi: mt76: mt7921: add ack signal support
f47087a6dd62 wifi: mt76: mt7996: fix chainmask calculation in mt7996_set_antenna()
2f3b0acc1588 wifi: mt76: mt7996: update register for CFEND_RATE
7e9540dcbd70 wifi: mt76: mt7996: do not hardcode vht beamform cap
a37e427d0959 wifi: mt76: connac: fix POWER_CTRL command name typo
98aa346042bd wifi: mt76: mt7915: remove BW160 and BW80+80 support
94fed6a43541 wifi: mt76: mt7921: fix invalid remain_on_channel duration
3c162384d80a wifi: mt76: introduce mt76_queue_is_wed_rx utility routine
a409a9454587 wifi: mt76: mt7915: fix memory leak in mt7915_mcu_exit
8b27ecd3a684 wifi: mt76: mt7996: fix memory leak in mt7996_mcu_exit
683760461dd0 wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup
0c750cf08f85 wifi: mt76: dma: fix memory leak running mt76_dma_tx_cleanup
5de9ae29bea2 wifi: mt76: mt7915: avoid mcu_restart function pointer
dad96dd3e62d wifi: mt76: mt7603: avoid mcu_restart function pointer
19d36dd9c8ea wifi: mt76: mt7615: avoid mcu_restart function pointer
6fe2c2383d3d wifi: mt76: mt7921: avoid mcu_restart function pointer
9df89143bf71 wifi: mt76: mt7915: get rid of wed rx_buf_ring page_frag_cache
8d51d11760cb wifi: mt76: fix switch default case in mt7996_reverse_frag0_hdr_trans
0d8057dbd51c wifi: mt76: mt7921u: add support for Comfast CF-952AX
ddbf4e933d54 wifi: mt76: mt7915: set sku initial value to zero
06a8904e954e wifi: mt76: mt7915: wed: enable red per-band token drop
724a337caef9 wifi: mt76: mt7915: fix WED TxS reporting
747ca943a5bb wifi: mt76: add flexible polling wait-interval support
133d7859977a wifi: mt76: mt7921: reduce polling time in pmctrl
5fe319a0550e wifi: mt76: add memory barrier to SDIO queue kick
822f060b9d19 wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent
c6794954a723 wifi: mt76: mt7915: fix memory leak in mt7915_mmio_wed_init_rx_buf
9686cd7cc65c wifi: mt76: switch to page_pool allocator
04da4eaa8235 wifi: mt76: enable page_pool stats
1af4a911ebcb wifi: mt76: mt7915: release rxwi in mt7915_wed_release_rx_buf
e8c10835cf06 wifi: mt76: fix compile error without CONFIG_PAGE_POOL_STATS
0cf0ede7cc42 net: ethernet: mtk_wed: add reset to rx_ring_setup callback
715b3ed9708a net: ethernet: mtk_wed: add reset to tx_ring_setup callback
9107381d0ff3 wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read
36d2a5bf7802 wifi: mt76: mt7996: rely on mt76_connac2_mac_tx_rate_val
c67f57d2cda2 wifi: mt76: dma: add reset to mt76_dma_wed_setup signature
3dace36e2941 wifi: mt76: dma: reset wed queues in mt76_dma_rx_reset
4b229d2da562 wifi: mt76: mt7915: add mt7915 wed reset callbacks
f83958376085 wifi: mt76: mt7915: complete wed reset support
321edbb414dc wifi: mt76: mt7996: rely on mt76_connac_txp_common structure
bdb7dc38a6d1 wifi: mt76: mt7996: rely on mt76_connac_txp_skb_unmap
8688756305c6 wifi: mt76: mt7996: rely on mt76_connac_tx_complete_skb
fbf986dbd4c0 wifi: mt76: mt7996: rely on mt76_connac2_mac_decode_he_radiotap
adc556cbce37 wifi: mt76: mt7996: avoid mcu_restart function pointer
5eb4e2303be4 wifi: mt76: remove __mt76_mcu_restart macro
e7a61c5f70f5 wifi: mt76: add EHT phy type
b375845abc10 wifi: mt76: connac: add CMD_CBW_320MHZ
68b17a243332 wifi: mt76: connac: add helpers for EHT capability
02ec1f61b3a2 wifi: mt76: connac: add cmd id related to EHT support
9209294cd81b wifi: mt76: increase wcid size to 1088
5e85136c9b2f wifi: mt76: add EHT rate stats for ethtool
a171f672fdeb wifi: mt76: mt7996: add variants support
eda8fd62c105 wifi: mt76: mt7996: add helpers for wtbl and interface limit
4a5a9f4cdc3b wifi: mt76: mt7996: rework capability init
06b73c155680 wifi: mt76: mt7996: add EHT capability init
ae71a1b8294f wifi: mt76: mt7996: add support for EHT rate report
65bdfae2991d wifi: mt76: mt7996: enable EHT support in firmware
b2360d59747c wifi: mt76: mt7996: add EHT beamforming support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-02-02 11:16:49 +01:00
Petr Štetiar
3d7d93cf65 ubus: fix wrong package mirror hash
I've somehow managed to commit wrong package mirror hash in commit 36076b5a40
("ubus: update to version 2022-06-15"), so lets fix it by using a proper
one.

Fixes: 36076b5a40 ("ubus: update to version 2022-06-15")
Reported-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-01-30 10:58:00 +01:00
Felix Fietkau
83d3e255f1 bridger: update to the latest version
8be8bb9df789 nl: fix accessing hairpin mode and isolated from the right attribute set

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-29 10:08:21 +01:00
Felix Fietkau
908397f6d2 mac80211: backport napi_build_skb for 5.10
It is needed for an upcoming mt76 update

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-29 10:08:21 +01:00
Felix Fietkau
74e5e213da ucode: update to the latest version
1c8df08824ef style: add .editorconfig file
ec167d39b803 nl80211: refactor command bitmask handling
6704ec0d5b29 nl80211: add support for registering an uloop based listener
48a6eac1da15 fs: implement `fs.pipe()`
f1be0d725735 types: fix array unshift operations and add test coverage
941d14837faf Merge pull request #138 from nbd168/nl80211

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-29 10:08:21 +01:00
Daniel Golle
90dbdb4941 uboot-envtools: filogic: bpi-r3: fix env selection
Selecting the environment when booting from SD card has been broken by
a previous commit. Fix it.

Fixes: f46355b4d7 ("uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-29 03:43:58 +00:00
Daniel Golle
e51a57e192 uboot-envtools: mt7622: bpi-r64: fix env selection
Selecting the environment when booting from SD card has been broken by
a previous commit. Fix it.

Fixes: 84b5b0f88c ("uboot-envtools: mediatek/mt7622: don't rely on mapped rootfs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-29 03:43:58 +00:00
Chen Minqiang
781a3ae5dc base-files: fix nand_do_platform_check fail
This change ensures compatibility with both types of sysupgrade-tar files.

1. For some boards like xiaomi,redmi-router-ax6s, sysupgrade-tar
   is pack in directory `vendor,name/`

2. For some boards like xiaomi,mi-router-3g, sysupgrade-tar is pack
   in directory `vendor_name/`

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2023-01-29 01:02:45 +00:00
Andre Heider
b246385126 ucode: move to the lang submenu
Just as lua or the various languages from the package feed.
libucode is the exception, so move it to the libs menu instead.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-28 22:37:35 +01:00
Andre Heider
9902c8520b uhttpd: clean up Makefile
uhttpd's cmake options all default to ON. Either we set all of them or
none if the defaults need to be changed. Let's go with the latter.

Because support for all modules is always compiled in, remove two unused
and useless config toggles.

uhttpd detects and uses libcrypt itself, no need to add it here again.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-28 22:37:35 +01:00
Hauke Mehrtens
d1893f1c88 px5g-mbedtls: Use getrandom()
Instead of accessing /dev/urandom use the getrandom syscall. This way we
do not have to keep the file open all the time.
This also fixes a compile error with glibc:

--------
px5g-mbedtls.c: In function '_urandom':
px5g-mbedtls.c:48:9: error: ignoring return value of 'read' declared with attribute 'warn_unused_result' [-Werror=unused-result]
   48 |         read(urandom_fd, out, len);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
--------

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-28 22:26:06 +01:00
Tony Butler
a7f3a51982 kernel: add kmod-lib-842
"842" is a compression scheme and this is the software implementation
which is too slow to really use beyond a proof of concept.  It can be
selected in ZRAM, ZSWAP, or `fs/pstore`, and is here for completeness.
In general you need a Power8 or better with 842-in-hardware for it to
be fast, but other 842-accelerators are emerging.

Signed-off-by: Tony Butler <spudz76@gmail.com>
2023-01-28 21:19:17 +01:00
Michael Pratt
52992efc34 ath79: add support for Senao Engenius EWS660AP
FCC ID: A8J-EWS660AP

Engenius EWS660AP is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9558 SOC		2.4 GHz, 3x3
  - QCA9880 WLAN	mini PCIe card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - AR8033 PHY		SGMII GbE with PoE+ OUT
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)

**MAC addresses:**

  Base MAC addressed labeled as "MAC"
  Only one Vendor MAC address in flash

  eth0 *:d4 MAC art 0x0
  eth1 *:d5 --- art 0x0 +1
  phy1 *:d6 --- art 0x0 +2
  phy0 *:d7 --- art 0x0 +3

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs.bin to '0101A8C0.img'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

**Format of OEM firmware image:**

  The OEM software of EWS660AP is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-ews660ap-uImage-lzma.bin
    openwrt-ar71xx-generic-ews660ap-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Tested-by: Niklas Arnitz <openwrt@arnitz.email>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-28 20:34:00 +01:00
Nick Hainke
364a9be338 ethtool: update to 6.1
Release notes:
https://lore.kernel.org/netdev/20221219225600.r54vejiqapn266cm@lion.mk-sys.cz/T/

Add patches fixing compilation:
- 100-uapi-Bring-in-if-h.patch
- 101-netlink-Fix-maybe-uninitialized-meters-variable.patch
- 102-raw-marvell-c-Fix-build-with-musl-libc.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-28 20:26:22 +01:00
Hauke Mehrtens
015c108755 relayd: bump to version 2023-01-28
f646ba4 route: Fix compile warning with glibc

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-28 20:24:22 +01:00
Hauke Mehrtens
d14559e9df uhttpd: update to latest Git HEAD
47561aa mimetypes: add audio/video support for apple airplay
6341357 ucode: respect all arguments passed to send()

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-28 19:31:42 +01:00
David Bauer
a63430eac3 mac80211: use 802.11ax iw modes
This adds missing HE modes to mac80211_prepare_ht_modes.

Previously mesh without wpa_supplicant would be initialized with 802.11g
/NO-HT only, as this method did not parse channel bandwidth for HE
operation.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-28 13:53:39 +01:00
Petr Štetiar
36076b5a40 ubus: update to version 2022-06-15
Update which contains just a following fix:

 * ubusd: add lookup command queuing support

   Defers and continues a client's lookup command to avoid unnecessary
   buffering under load.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2023-01-27 11:04:07 +01:00
Nick Hainke
1a47f19080 linux-firmware: update to 20230117
Changes:
32d3199 linux-firmware: Update firmware file for Intel Bluetooth AX201
2da8a7a linux-firmware: Update firmware file for Intel Bluetooth AX201
8b5ddf4 linux-firmware: Update firmware file for Intel Bluetooth AX211
4219dac linux-firmware: Update firmware file for Intel Bluetooth AX211
fb34135 linux-firmware: Update firmware file for Intel Bluetooth AX210
becd3fc linux-firmware: Update firmware file for Intel Bluetooth AX200
7101c57 linux-firmware: Update firmware file for Intel Bluetooth AX201
49e87fa linux-firmware: Update firmware file for Intel Bluetooth 9560
86b73ce linux-firmware: Update firmware file for Intel Bluetooth 9260
3723b48 brcm: add configuration files for CyberTan WC121
7f626ef qcom: add firmware files for Adreno A200
fc5a25f rtw89: 8852c: update fw to v0.27.56.10
2ba1bea  QCA: Add Bluetooth firmware for QCA2066
a1ad1d5 amdgpu: add VCN4.0.4 firmware from amd-5.4
9e01e17 amdgpu: add SMU13.0.7 firmware from amd-5.4
3a50eb8 amdgpu: add SDMA6.0.2 firmware from amd-5.4
19995fb amdgpu: add PSP13.0.7 firmware from amd-5.4
32e7c93 amdgpu: add GC11.0.2 firmware from amd-5.4
20c8060 amdgpu: add DCN3.2.1 firmware from amd-5.4
5c8e895 amdgpu: update VCN4.0.0 firmware from amd-5.4
66b3435 amdgpu: update SMU13.0.0 firmware from amd-5.4
604df78 amdgpu: update SDMA6.0.0 firmware from amd-5.4
3e9169a amdgpu: update PSP13.0.0 firmware from amd-5.4
bd1b7f7 amdgpu: update GC11.0.0 firmware from amd-5.4
c8ff1f4 iwlwifi: add new FWs from core76-35 release
5630963 iwlwifi: update cc/Qu/QuZ firmwares for core76-35 release
8bbec22 iwlwifi: add new FWs from core75-47 release
e20a687 iwlwifi: update 9000-family firmwares to core75-47
504b691 amdgpu: update renoir DMCUB firmware
1ed02d5 amdgpu: Update renoir PSP firmware
d0598c3 amdgpu: update copyright date for LICENSE.amdgpu
cee86df linux-firmware: update firmware for MT7921 WiFi device
e2d1174 linux-firmware: update firmware for MT7922 WiFi device
ce7cc73 linux-firmware: update firmware for mediatek bluetooth chip (MT7921)
91f4c6b linux-firmware: update firmware for mediatek bluetooth chip (MT7922)
52e62d6 cxgb4: Update firmware to revision 1.27.1.0
4704e25 qca: Update firmware files for BT chip WCN6750
c9c1958 rtw89: 8852c: update fw to v0.27.56.9
9e91f0c rtw89: 8852c: update fw to v0.27.56.8

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-26 22:15:43 +01:00
Linhui Liu
340d3d84dc firmware: intel-microcode: update to 20221108
Changelog:
  * New Microcodes:
    sig 0x000606c1, pf_mask 0x10, 2022-08-07, rev 0x1000201, size 286720
    sig 0x000b0671, pf_mask 0x32, 2022-09-07, rev 0x010e, size 204800

  * Updated Microcodes:
    sig 0x000706e5, pf_mask 0x80, 2022-08-02, rev 0x00b6, size 113664
    sig 0x000806c1, pf_mask 0x80, 2022-06-28, rev 0x00a6, size 110592
    sig 0x000806d1, pf_mask 0xc2, 2022-06-28, rev 0x0042, size 102400
    sig 0x000806ec, pf_mask 0x94, 2022-07-31, rev 0x00f4, size 105472
    sig 0x00090661, pf_mask 0x01, 2022-07-15, rev 0x0017, size 20480
    sig 0x00090672, pf_mask 0x07, 2022-09-19, rev 0x0026, size 218112
    sig 0x00090675, pf_mask 0x07, 2022-09-19, rev 0x0026
    sig 0x000b06f2, pf_mask 0x07, 2022-09-19, rev 0x0026
    sig 0x000b06f5, pf_mask 0x07, 2022-09-19, rev 0x0026
    sig 0x000906a3, pf_mask 0x80, 2022-09-19, rev 0x0424, size 217088
    sig 0x000906a4, pf_mask 0x80, 2022-09-19, rev 0x0424
    sig 0x000906ed, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 104448
    sig 0x000a0652, pf_mask 0x20, 2022-07-31, rev 0x00f4, size 96256
    sig 0x000a0653, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 97280
    sig 0x000a0655, pf_mask 0x22, 2022-07-31, rev 0x00f4, size 96256
    sig 0x000a0660, pf_mask 0x80, 2022-07-31, rev 0x00f4, size 97280
    sig 0x000a0661, pf_mask 0x80, 2022-07-31, rev 0x00f4, size 96256
    sig 0x000a0671, pf_mask 0x02, 2022-08-02, rev 0x0056, size 103424

We need to update to this version because
https://ftp.debian.org/debian/pool/non-free/i/intel-microcode/intel-microcode_3.20220809.1.tar.xz
has been removed.

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
2023-01-26 00:22:08 +01:00
Nick Hainke
d68a73a025 tcpdump: update to 4.99.3
Changes:
https://git.tcpdump.org/tcpdump/blob/032e4923e5202ea4d5a6d1cead83ed1927135874:/CHANGES

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-26 00:17:59 +01:00
Wenli Looi
f0eb73a888 ath79: consolidate Netgear EX7300 series images
This change consolidates Netgear EX7300 series devices into two images
corresponding to devices that share the same manufacturer firmware
image. Similar to the manufacturer firmware, the actual device model is
detected at runtime. The logic is taken from the netgear GPL dumps in a
file called generate_board_conf.sh.

Hardware details for EX7300 v2 variants
---------------------------------------
SoC: QCN5502
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 1 gigabit port
Wireless 2.4GHz (currently unsupported due to lack of ath9k support):
- EX6250 / EX6400 v2 / EX6410 / EX6420: QCN5502 3x3
- EX7300 v2 / EX7320: QCN5502 4x4
Wireless 5GHz:
- EX6250: QCA9986 3x3 (detected by ath10k as QCA9984 3x3)
- EX6400 v2 / EX6410 / EX6420 / EX7300 v2 / EX7320: QCA9984 4x4

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
2023-01-25 00:42:52 +01:00
Christian Marangi
b61404a6ad
rssileds: bump PKG_RELEASE due to libiwinfo ABI change
Bump PKG_RELEASE due to libiwinfo ABI change to trigger a package
rebuild.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-23 13:55:42 +01:00
Christian Marangi
114c168522
rpcd: bump libiwinfo abi requirement to >= 2023-01-21
Bump libiwinfo abi requirement to >= 2023-01-21 for rpcd.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-23 13:55:42 +01:00
Christian Marangi
57586ddd71
iwinfo: update to latest Git HEAD
1e4e709 iwinfo: readd missing define for IWINFO_AUTH in header

Fixes: #11860
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-23 13:54:13 +01:00
Christian Marangi
fb7f4d4b54
fstool: bump to latest Git HEAD
1ea5855 partname: Introduce fstools_partname_fallback_scan option

While at it also drop AUTORELEASE from PKG_RELEASE.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-22 17:30:42 +01:00
ValdikSS ValdikSS
2fc170cc21 openssl: fix VIA Padlock AES-192 and 256 encryption
Byte swapping code incorrectly uses the number of AES rounds to swap expanded
AES key, while swapping only a single dword in a loop, resulting in swapped
key and partially swapped expanded keys, breaking AES encryption and
decryption on VIA Padlock hardware.

This commit correctly sets the number of swapping loops to be done.

Upstream: 2bcf8e69bd

Acked-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: ValdikSS ValdikSS <iam@valdikss.org.ru>
2023-01-22 01:33:33 +01:00
Hannu Nyman
a57796b137
dnsmasq: set an increased cachesize default value
Dnsmasq DNS cache size is only 150 by default.
Set the uci default value to 1000, so that cache gets used more
and unnecessary DNS queries to upstream can be avoided.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2023-01-21 11:13:44 +01:00
Christian Marangi
5d409062a3
rpcd: update to latest Git HEAD
c0df2a7 iwinfo: add "band" and "mhz" to the scan output
06ad60f iwinfo: add "band" to the freqlist output
b32fd32 iwinfo: add flags to freqlist output

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-21 01:26:19 +01:00
Christian Marangi
f3d8de7398
iwinfo: update to latest Git HEAD
Bump ABI to 20230121 due to struct changes

f766138 cli: print the flags on the frequency list
8ee7971 lib: add IWINFO_FREQ_FLAG_NAMES
81184d2 nl80211: fix some comments
2c4ee84 nl80211: prefer non-supplicant-based devices
6194aaf nl80211: simplify iterating over phy's devices
acbf4fe nl80211: remove redundant check in nl80211_phy2ifname()
0172c97 cli: print the frequency and band on the scan list
bbe424f cli: print the band on the frequency list
afa147c nl80211: add "mhz" and "band" to iwinfo_scanlist_entry
0d5ea34 nl80211: add "band" to iwinfo_freqlist_entry
dba0f06 nl80211: add support for radiation and indoor chan restriction
7e3d7de iwinfo: reorganize iwinfo header to enum and defines
9b47b03 devices: add USB devices supported by the mt76 driver
c0fda7c utils: skip comment lines when parsing devices.txt
dbc0ee7 cli: describe USB devices as such
891acee devices: add MediaTek MT7628 card
fac0787 devices: add support for declaring compatible matched devices

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-21 01:23:22 +01:00
Christian Marangi
bd0f9d8ffc
fstools: bump to latest Git HEAD
e9b59f0 partname: Ignore root=PARTUUID...

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-21 01:02:25 +01:00
Brian Norris
d3c19c71f6
base-files: Remove nand.sh dependency from emmc upgrade
emmc_do_upgrade() relies on identify() from the nand.sh upgrade helper.
This only works because FEATURES=emmc targets also tend to include
FEATURES=nand.

Rename identify_magic() to identify_magic_long() to match the common.sh
style and make it clear it pairs with other *_long() variants (and not,
say *_word()).

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2023-01-21 01:02:23 +01:00
Brian Norris
bf1634f318
ucode: update to latest Git HEAD
To bring in isatty() support.

Includes new commits:

be30472bfdbb fs: add `isatty()` function
0a58d510529e nl80211: add support for NL80211_ATTR_MPATH_INFO

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[ remove additional merge commit ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-21 01:02:23 +01:00
André Valentin
5dee596501
ipq807x: Add ZyXEL NBG7815
ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1 GB 2x Nanya NT5CC256M16ER-EK
* Storage:
        * 8MB serial flash Winbond W25Q64DW
        * 4GB eMMC flash Kingston EMMC04G-M627
* Ethernet:
        * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port
        * 1x2.5G RJ45 port (QCA8081) with 1x status LED
        * 1x10G RJ45 port (AQR113C) with 1x status LED
* Switch: Qualcomm Atheros QCA8075
* WLAN:
        * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
        * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
* Bluetooth CSR8811 using HSUART, currently unsupported
* USB: 1x USB3.0 Type-A port
* LED-s currently not supported:
        * White
        * Dark Blu
        * Amber
        * Purple
        * Purple and dark blue
        * Red
* Buttons:
        * 1x Soft reset
* Power: 12V DC Jack

Installation instructions:
* Disconnect WAN
* Reset device to factory defaults by pushing reset button 15 sec,
  LEDs should lit orange color.
* After 5-10 minutes, when the LEDs turn constant dark blue,
  put your LAN cable and connect at address 192.168.123.1 by telnet on port 23
* Login with
  NBG7815 login: root
  password: nbg7815@2019
* cd /tmp/ApplicationData
* wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://...
* wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
* run flash_to_openwrt.sh
If you can't use wget, you can transfer the files via nc.
See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details.

Bluetooth usage:
* you need at least package bluez-utils, recommended bluez-daemon
* run following commands to enable and start
  hciattach  /dev/ttyMSM1 bcsp
  hciconfig hci0 up

Many thanks to itorK for his work on this device:
https://github.com/itorK/openwrt/tree/nbg7815

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: André Valentin <avalentin@marcant.net>
2023-01-19 13:26:15 +01:00
David Bauer
00f1463df7 mbedtls: move source modification to patch
Patch the mbedtls source instead of modifying the compile-targets
in the prepare buildstep within OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-18 23:36:22 +01:00
Jo Deisenhofer
ef9acfb68b uboot-mediatek: Fix ramips/mt76x8 buildbot
Move defines from header to defconfig
The package build and the Buildbot hang in 'make syncconfig' for
u-boot-ravpower_rp-wd009 because CONFIG_SYS_MIPS_TIMER_FREQ is not in
the .config, causing a console prompt. Also moved two other defines in
defconfig causing duplicate definition warnings.

Fixes: 3d5c5427e1 ("uboot-mediatek: update to U-Boot 2023.01")
Signed-off-by: Jo Deisenhofer <jo.deisenhofer@gmail.com>
2023-01-18 20:26:39 +00:00
Vincent Tremblay
afcf1a4de4
uboot-envtools: ipq40xx: fix WHW03V2 mtd partition
The configured u_env partition for the Linksys WHW03 V2 was not correct.
It should have been set to mtd6.

This fix allow to flash the OEM firmware from OpenWRT and to change the
boot partition using fw_setenv.

Fixes: 9e4ede8344 ("ipq40xx: add support for Linksys WHW03 V2")
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-18 00:07:30 +01:00
Josef Schlehofer
2f83369e3e uboot-mvebu: update to version 2023.01
In the version 2023.01, the U-boot image was renamed because of the
upstream change [1]

[1] 87ac4b4b4c

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2023-01-17 23:17:33 +01:00
Nick Hainke
e846606900 libpcap: update to 1.10.3
Changelog:
https://git.tcpdump.org/libpcap/blob/95691ebe7564afa3faa5c6ba0dbd17e351be455a:/CHANGES

Refresh patch:
- 300-Add-support-for-B.A.T.M.A.N.-Advanced.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-17 23:16:02 +01:00
Nick Hainke
a04bbbbea4 ipset: update to 7.17
Release notes:
https://lwn.net/Articles/918784/

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-17 23:14:46 +01:00
Martin Schiller
6e4c9738be ltq-vdsl-vr11-app: add version 4.23.1 for vr11 targets
This uses version 4.23.1 of the dsl_cpe_control package from the Intel
UGW 8.5.2.10 for the VRX518.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[rebased]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 4.23.1, added Jan's vector mac patch, fix warnings,
 switch to tag tarball]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[add missing nLine in autoboot script, fix disconnect on termination,
 remove unneeded VR9 leftovers in init script]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Andre Heider
6361eb47cd ltq-dsl-base: enable for ipq40xx
This is required by the DSL userland tool for hotplug support.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
1f7ec35077 kernel: add new ltq-vdsl-vr11 driver
This uses version 4.23.1 of the drv_dsl_cpe_api package from the Intel
UGW 8.5.2.10 for the VRX518.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[rebased and updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 4.23.1, switch to tag tarball, update patches]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[added fix for elapsed time and upstream MINEFTR]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
bc442076f2 kernel: add new ltq-vdsl-vr11-mei driver
This uses version 1.11.1 of the drv_mei_cpe package from the Intel UGW
8.5.2.10 for the VRX518.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 1.11.1, switch to tag tarball, update patches]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[update for kernel 5.15]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Andre Heider
2a0aa9eefa ltq-ifxos: enable for ipq40xx
This is required for the MEI CPE driver.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
474bbe23b7 kernel: add Intel/Lantiq VRX518 TC driver
This driver version is also included in Intel UGW 8.5.2.10.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 1.5.12.4, switch to tag tarball]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[add working software data path]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Martin Schiller
568d17989f kernel: add Intel/Lantiq VRX518 EP driver
This driver was picked from the Intel UGW 8.5.2.

Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[updated for kernel 5.10]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
[update to 8.5.2]
Signed-off-by: Andre Heider <a.heider@gmail.com>
[fix masking interrupts and add locking]
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Andre Heider <a.heider@gmail.com>
2023-01-16 23:41:41 +00:00
Daniel Golle
f0a98bf048
procd: update to git HEAD
04d7570 jail: fs: don't overwrite existing mount target
 6b9629b jail: don't assume positive return value of creat
 190f13a init: attempt to mount efivarfs

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-16 22:05:01 +00:00
Dirk Buchwalder
26c095cb4d ipq807x: add Dynalink DL-WRX36
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 256MB Nand
    •     Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
    •     1x USB 3.0

    •     1 gpio-controlled dual color led (blue/red)

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard (J1004)
        the connector size is a 4-pin 2.0 mm JST PH.
        RX/TX is working, u-boot bootwait is active, secure boot is enabled.

        Notes:
	- Serial is completely deactivated in the stock firmware image.
	- This commit adds only single partition support, that means
	  sysupgrade is upgrading the current rootfs partition.
	- Installation can be done by serial connection or
	  SSH access on OEM firmware

	Installation Instructions:

	Most part of the installation is performed from an initramfs image
	running OpenWrt, and there are two options to boot it.

	Boot initramfs option 1: Using serial connection (3.3V)
	1. Stop auto boot to get to U-boot shell
	2. Transfer initramfs image to device
	   (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
	   Tested using TFTP and a FAT-formatted USB flash drive.
	3. Boot the initramfs image
	   # bootm

	Boot initramfs option 2: From SSH access on OEM firmware
	1. Copy the initramfs image to a FAT-formatted flash drive
	   (tested on single-partition drive) and connect it to device USB port.
	2. Change boot command so it loads the initramfs image on next boot
	   Fallback to OEM firmware is provided.
	   # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
	3. Reboot the device to boot the initramfs
	   # reboot

	Install OpenWrt from initramfs image:
	1. Use SCP (or other way) to transfer OpenWrt factory image
	2. Connect to device using SSH (on a LAN port)
	3. Check MTD partition table.
	   rootfs and rootfs_1 should be mtd18 and mtd20
	   depending on current OEM slot.
	   # cat /proc/mtd
	4. Do a ubiformat to both rootfs partitions:
	   # ubiformat /dev/mtd18 -y -f /path_to/factory_image
	   # ubiformat /dev/mtd20 -y -f /path_to/factory_image
	5. Set U-boot env variable: mtdids
	   # fw_setenv mtdids 'nand0=nand0'
	6. Get offset of mtd18 to determine current OEM slot
	   - If current OEM slot is 1, offset is 16777216  (0x1000000)
	   - If current OEM slot is 2, offset is 127926272 (0x7a00000)
	   # cat /sys/class/mtd/mtd18/offset
	7. Set U-boot env variable: mtdparts
	   If current OEM slot is 1, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
	   If current OEM slot is 2, run:
	   # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
	8. Set U-boot env variable: bootcmd
	   # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
	9. Reboot the device
	   # reboot

        Note: this PR adds only single partition support, that means sysupgrade is
              upgrading the current rootfs partition

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Matthew Hagan
6e03304c76 ipq807x: add Edgecore EAP102
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be
powered by either PoE or AC adapter.

Device info:
 - IPQ8071-A SoC
 - 1GiB RAM
 - 256MiB NAND flash
 - 32MiB SPI NOR
 - 2 Ethernet ports
 - 1 Console port
 - 2GHz/5GHz AX WLAN
 - 2 USB 2.0 ports

Install instructions:

Prerequistes - TFTP server, preferrably within 192.168.1.0/24
	       Console cable plugged in (115200 8N1 no flow control)

1. Power on device and interrupt u-boot to obtain u-boot CLI

2. set serverip to IP address of the TFTP server:

	`setenv serverip 192.168.1.250`

3. Download image from TFTP server:

	`tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi`

4. Flash ubi image to both partitions and reset:

	`sf probe
	 imxtract 0x44000000 ubi
	 nand device 0
	 nand erase 0x0 0x3400000
	 nand erase 0x3c00000 0x3400000
	 nand write $fileaddr 0x0 $filesize
	 nand write $fileaddr 0x3c00000 $filesize
	 reset`

Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
2ddb2057cd ipq807x: Add Xiaomi AX9000
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
	* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
	* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
	* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
	* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
	* System (Blue and Yellow)
	* Network (Blue and Yellow)
	* RGB light bar on top in X shape
* Buttons:
	* 1x Power switch
	* 1x Soft reset
	* 1x Mesh button
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Dirk Buchwalder
bd17683261 ipq807x: add QNAP 301w
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.

Specifications:

    •     CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
    •     RAM: 1024MB of DDR3
    •     Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
          (contains art and u-boot-env)
    •     Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
          5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate

    •     LEDs:
          7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs

            • Buttons: 1x soft reset / 1x WPS
            • Power: 12V DC jack

        A poulated serial header is onboard.
        RX/TX is working, bootwait is active, secure boot is not enabled.

        SSH can be activated in the stock firmware, hold WPS button til the second beep
	(yes the router has a buzzer)
        SSH is available on port 22200, login with user admin and
	password "mac address of the router".

        Installation Instructions:

            • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
            • stop auto boot
            • setenv serverip 192.168.10.1
            • setenv ipaddr 192.168.10.10
            • tftpboot the initramfs image
              (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
            • bootm

            • make sure that current_entry is set to "0":
              "fw_printenv -n current_entry" should be print "0". If not,
	       do "fw_setenv current_entry 0"
            • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
	          to the device to /tmp folder
            • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
              this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
            • reboot

        Note: this leaves the second kernel / rootfs parition untouched. So if you want
              to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
	       "saveenv", "bootipq".
              Stock firmware should start from the second partition.
	      Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
	      in the first partitions

        Make 10G Aquantia phy's work:
              The aquantia phy's need a firmware to work. This can either be loaded
	      in linux with a userspace tool or in u-boot.

              I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
	      aq_load_fw available in u-boot. But first the right firmware needs to write
	      to the 0:ETHPHYFW mtd partition (it is empty on my device)

              Grab the ethphy firmware image from:
	      https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
	      and scp that to openwrt.

              Check the 0:ETHPHYFW partition number:
              cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.

              Backup the 0:ETHPHYFW partition:
              dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.

              Write the new firmware image to the 0:ETHPHYFW partition:
              "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".

              Reboot to u-boot.

              Check if aq_load_fw is working:

              "aq_load_fw 0", that checks the firmware and if successfull,
	      loads iram and dram to one of the aquantia phy's.

              If that worked, add the aq_load_fw to the bootcmd:
              setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"

              "saveenv"

              "reset"

              Board reboots and the firmware load to both phy's should start and
	      then openwrt boots.

              Check if the 10G ports work.

              Note: lan port labeled "10G-2" is configured as WAN port as per default.
	      All other port are in the br-lan. This can be changed in the network config.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Dirk Buchwalder
a36fc589fe ipq807x: add Edimax CAX1800
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.

Specifications:

    •     CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
    •     RAM: 512MB of DDR3
    •     Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
    •     Ethernet: 1x 1G RJ45 port (QCA8072) PoE
    •     WLAN:
          2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
          5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate

    •     LEDs:
          3 x GPIO-controlled System-LEDs
          (form one virtual RGB System-LED)
            black_small_square  Buttons: 1x soft reset
            black_small_square  Power: 12V DC jack or PoE (802.3af )

        An unpopulated serial header is onboard.
        RX/TX is working, bootwait is active, secure boot is not enabled.

        SSH can be activated in the stock firmware, but it drops only
        to a limited shell .

        Installation Instructions:

            black_small_square obtain serial access
            black_small_square stop auto boot

            black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
            black_small_square bootm

            black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
	      to the device
            black_small_square write the image to the NAND:
            black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
            black_small_square ubiformat /dev/mtd0 -f -y  openwrt-ipq807x-generic-edimax_cax1800-squashfs-
              nand-factory.ubi
            black_small_square reboot

	Note: Device is not using dual partitioning (NAND contains other partitions
        with different manufacture data etc.)
	Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.

Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
2023-01-16 12:42:23 +01:00
Zhijun You
8253cb2de5 ipq807x: add Redmi AX6
Redmi AX6 is a budget 802.11ax dual-band router/AP

Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
	* System (Blue/Yellow)
	* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Zhijun You <hujy652@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
8364f08164 ipq807x: add Xiaomi AX3600
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
	* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
	* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
	* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
	* System (Blue and Yellow)
	* IoT (Blue)
	* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack

Installation instructions:

Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access

Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs

4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!

5. Use the command ubiformat to flash the opposite mtd with UBI image:

If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit

otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit

6. Reboot the device by:
reboot

Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:

7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin

Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
2558e7b443 kernel: add Qualcomm NSS dataplane ethernet driver
Qualcomm NSS-DP is as its name says Qualcomms ethernet driver for the NSS
subsystem (Networking subsystem) built-into various Qualcomm SoCs.

It has 2 modes of operation:
* Without NSS FW and rest of code required for offloading

This is the one that we will use as the amount of kernel patching required
for NSS offloading and the fact that its not upstreamable at all makes it
unusable for us.

Driver in this mode is rather basic, it currently only offers NAPI GRO
(Added by us as part of the fixup) and basically relies on the powerfull
CPU to get good throughput.

* With NSS FW and rest of code required for offloading

In this mode, driver just registers the interfaces and hooks them into
NSS-ECM to allow offloading.
This mode is not viable for use in OpenWrt due to reasons already described
above.

This driver is required for ipq807x to have wired networking until a better
one is available, so lets add the fixed-up version for 5.15 for now.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
c608f70325 kernel: add Qualcomm SSDK driver
Qualcomm SSDK is driver for Qualcomm Atheros switches and PHY-s.

It is quite complicated and used by rest of the Qualcomm SDK stack for
anything switch or PHY related.

It is required for IPQ807x support as currently, there is no better driver
for the built-in switch or UNIPHY.

So, lets add the fixed-up version that supports kernel 5.15 for use on
ipq807x target until a better driver is available.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
35f28f2838 mac80211: add ath11k AHB support
This is the follow up to the PCI support commit now providing support for
AHB variant as well, though currently only for ipq807x as that is only
OpenWrt supported SoC ath11k supports as well.

Currently, we are disabling coldboot calibration on ipq807x as it does not
work, there is a remoteproc bug that makes it come late out of reset so
disable coldboot until that is fixed.

Also, as ath11k is quite memory hungry, we are introducing a config option
to use the limits for 512MB of RAM, similar to what QCA does downstream but
in way simpler and cleaner way so that 512MB save some RAM.
512MB profile is also set as the default for now.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
b5f32064ed ipq807x: add Qualcomm Atheros IPQ807x target
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
	* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
	* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
	* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
	* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
	* 5G: 2x2/80MHz (IPQ8070A)
	* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
	* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)

Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.

SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
4f592fb819 mac80211: ath11k: hack for multiple card support
This is a temporary workaround for supporting multiple cards or AHB+PCI.

There is ongoing upstream work to properly support this based of
advertised FW features, but that is still ongoing.

This is only supported on QCN9074 cards due to FW limitation, so HW ID
is checked in order to prevent breaking QCA6390 and other popular cards.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Robert Marko
af6da88814 firmware: add ath11k-firmware package
Package ath11k firmware for AHB devices as well as QCN9074 which is a non
consumer card targeted as a companion for QCA WiSoC-s.

linux-firmware is always out of date for these, so fetch them from Kalle-s
repo like we do for ath10k.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-16 12:42:23 +01:00
Harm Berntsen
09f313bfd7 ramips: mt7621: Add Arcadyan WE420223-99 support
The Arcadyan WE420223-99 is a WiFi AC simultaneous dual-band access
point distributed as Experia WiFi by KPN in the Netherlands. It features
two ethernet ports and 2 internal antennas.

Specifications
--------------
SOC   : Mediatek MT7621AT
ETH   : Two 1 gigabit ports, built into the SOC
WIFI  : MT7615DN
BUTTON: Reset
BUTTON: WPS
LED   : Power (green+red)
LED   : WiFi (green+blue)
LED   : WPS (green+red)
LED   : Followme (green+red)
Power : 12 VDC, 1A barrel plug

Winbond variant:
RAM   : Winbond W631GG6MB12J, 1GBIT DDR3 SDRAM
Flash : Winbond W25Q256JVFQ, 256Mb SPI
U-Boot: 1.1.3 (Nov 23 2017 - 16:40:17), Ralink 5.0.0.1

Macronix variant:
RAM   : Nanya NT5CC64M16GP-DI, 1GBIT DDR3 SDRAM
Flash : MX25l25635FMI-10G, 256Mb SPI
U-Boot: 1.1.3 (Dec  4 2017 - 11:37:57), Ralink 5.0.0.1

Serial
------
The serial port needs a TTL/RS-232 3V3 level converter! The Serial
setting is 57600-8-N-1. The board has an unpopulated 2.54mm straight pin
header.

The pinout is: VCC (the square), RX, TX, GND.

Installation
------------
See the Wiki page [1] for more details, it comes down to:

1. Open the device, take off the heat sink
2. Connect the SPI flash chip to a flasher, e.g. a Raspberry Pi. Also
   connect the RESET pin for stability (thanks @FPSUsername for reporting)
3. Make a backup in case you want to revert to stock later
4. Flash the squashfs-factory.trx file to offset 0x50000 of the flash
5. Ensure the bootpartition variable is set to 0 in the U-Boot
   environment located at 0x30000

Note that the U-Boot is password protected, this can optionally be
removed. See the forum [2] for more details.

MAC Addresses(stock)
--------------------
+----------+------------------+-------------------+
| use      | address          | example           |
+----------+------------------+-------------------+
| Device   | label            | 00:00:00:11:00:00 |
| Ethernet | + 3              | 00:00:00:11:00:03 |
| 2g       | + 0x020000f00001 | 02:00:00:01:00:01 |
| 5g       | + 1              | 00:00:00:11:00:01 |
+----------+------------------+-------------------+

The label address is stored in ASCII in the board_data partition

Notes
-----
- This device has a dual-boot partition scheme, but OpenWRT will claim
  both partitions for more storage space.

Known issues
------------
- 2g MAC address does not match stock due to missing support for that in
  macaddr_add
- Only the power LED is configured by default

References
----------
[1] https://openwrt.org/inbox/toh/arcadyan/astoria/we420223-99
[2] https://forum.openwrt.org/t/adding-openwrt-support-for-arcadyan-we420223-99-kpn-experia-wifi/132653

Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Harm Berntsen <git@harmberntsen.nl>
2023-01-15 13:41:02 +01:00
Vincent Tremblay
9e4ede8344 ipq40xx: add support for Linksys WHW03 V2
SOC:             Qualcomm IPQ4019
WiFi 1:          QCA4019 IEEE 802.11b/g/n
WiFi 2:          QCA4019 IEEE 802.11a/n/ac
WiFi 3:          QCA8888 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8811 (A12U)
Zigbee:          Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet:        Qualcomm Atheros QCA8072 (2-port)
Flash 1:         Mactronix MX30LF4G18AC-XKI
RAM (NAND):      SK hynix H5TC4G63CFR-PBA (512MB)
LED Controller:  NXP PCA9633 (I2C)
Buttons:         Single reset button (GPIO).

- The three WiFis were fully tested and are configured with the same settings as in the vendor firmware.
- The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream.
- Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working.

Bluetooth:
========
- Fully working with the following caveats:
  - RFKILL need to be enabled in the kernel.
  - An older version of bluez is needed as bccmd is needed to configure the chip.

Zigbee:
======
- The spidev device is available in the /dev directory.
- GPIOs are configured the same way as in the vendor firmware.
- Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working.

Installation:
=========
The squash-factory image can be installed via the Linksys Web UI:
1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device).
2. Login with your admin password.
3. To enter into the support mode, click on the "CA" link and the bottom of the page.
4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button.
5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups.

The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts.
If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row.

It can also be done via TFTP:
1. Setup a local TFTP server and configure its IP to 192.168.1.100.
2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server.
3. Connect to the device through the serial console.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2".
6. Once flashed, enter "reset" to reboot the device.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
2023-01-15 12:55:38 +01:00
Marcin Gajda
700c47a5f6 ipq40xx: Add support ZTE MF18A
Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home).
Device specification

SoC Type: Qualcomm IPQ4019
RAM: 256 MiB
Flash: 128 MiB SPI NAND (Winbond W25N01GV)
ROM: 2MiB SPI Flash (GD25Q16)
Wireless 2.4 GHz (IP4019): b/g/n, 2x2
Wireless 5 GHz (QCA9982): a/n/ac, 3x3
Ethernet: 2xGbE (WAN/LAN1, LAN2)
USB ports: No
Button: 2 (Reset/WPS)
LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up)
Power: 5VDC, 2,1A via USB-C socket
Bootloader: U-Boot
On board ZWave and Zigbee (EFR32 MG1P232GG..)  modules ( not supported by orginal software )
Installation

 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port,
   with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) :

    VCC (3.3V). Do not use unless you need to source power for the converer from it.
    TX
    RX
    GND

    Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1.

 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2

 3.Connect TFTP server to RJ-45 port (WAN/LAN1).

 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands:
    setenv serverip 192.168.0.2
    setenv ipaddr 192.168.0.1
    set fdt_high 0x85000000
    tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb
    bootm 0x84000000

 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do:

WEB PARITION

cat /dev/mtd8 > /tmp/mtd8.bin
scp /tmp/mtd8.bin root@YOURSERVERIP:/
rm /tmp/mtd8.bin
ROOT PARITION

cat /dev/mtd9 > /tmp/mtd9.bin
scp /tmp/mtd9.bin root@YOURSERVERIP:/
rm /tmp/mtd9.bin

If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command:
nand erase 0x1800000 0x1D00000

 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1):
ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before
ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it

 7. Install image via :
sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin

previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward.

Back to Stock (!!! need original dump taken from initramfs !!!) -------------

Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2
Connect serial console (115200,8n1) to serial console connector .
Connect TFTP server to RJ-45 port (WAN/LAN1).
rename mtd8.bin to web.img and mtd9.bin to root_uImage_s
Stop in u-Boot (using ESC button) and run u-Boot commands:
This will erase Web and RootFS:
nand erase 0x1000000 0x800000
nand erase 0x1800000 0x1D00000

This will restore RootFS:
tftpboot 0x84000000 root_uImage_s
nand erase 0x1800000 0x1D00000
nand write 0x84000000 0x1800000 0x1D00000

This will restore Web Interface:
tftpboot 0x84000000 web.img
nand erase 0x1000000 0x800000
nand write 0x84000000 0x1000000 0x800000

After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router

As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com

Signed-off-by: Marcin Gajda <mgajda@o2.pl>
2023-01-14 19:19:36 +01:00
Mikhail Zhilkin
1a35edfbdb ramips: add basic support for TP-Link EC330-G5u v1
This adds basic support for TP-Link EC330-G5u Ver:1.0 router (also known
as TP-Link Archer C9ERT).

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB, Nanya NT5CC64M16GP-DI
Flash: 128 MiB NAND, ESMT F59L1G81MA-25T
Wireless 2.4 GHz (MediaTek MT7615N): b/g/n, 4x4
Wireless 5 GHz (MediaTek MT7615N): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
Button: 4 (Led, WiFi On/Off, Reset, WPS)
LEDs: 7 blue LEDs, 1 orange(amber) LED, 1 white(non-gpio) LED
Power: 12 VDC, 2 A
Connector type: Barrel
Bootloader: First U-Boot (1.1.3), Main U-Boot (1.1.3). Additionally,
original TP-Link firmware contains Image U-Boot (1.1.3).

Serial console (UART)
---------------------
                            V
+-------+-------+-------+-------+
| +3.3V |  GND  |  TX   |  RX   |
+---+---+-------+-------+-------+
    |              J2
    |
    +--- Don't connect

Installation
------------
1. Rename OpenWrt initramfs image to test.bin and place it on tftp server
   with IP 192.168.0.5
2. Attach UART, switch on the router and interrupt the boot process by
   pressing 't'
3. Load and run OpenWrt initramfs image:
      tftpboot
      bootm
4. Once inside OpenWrt, switch to the first boot image:
      fw_setenv BootImage 0
5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image

Back to Stock
-------------
1. Run in the OpenWrt shell:
      fw_setenv BootImage 1
      reboot

Recovery
--------
1. Press Reset button and power on the router
2. Navigate to U-Boot recovery web server (http://192.168.0.1/) and upload
   the OEM firmware

MAC addresses
-------------
+---------+-------------------+-------------------+-------------+
|         | MAC example 1     | MAC example 2     | Algorithm   |
+---------+-------------------+-------------------+-------------+
| label   | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| LAN     | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WAN     | 72:ff:7b:xx:xx:f5 | 54:d4:f7:xx:xx:db | label+1 [1] |
| WLAN 2g | 68:ff:7b:xx:xx:f4 | 50:d4:f7:xx:xx:da | label       |
| WLAN 5g | 68:ff:7b:xx:xx:f6 | 50:d4:f7:xx:xx:dc | label+2     |
+---------+-------------------+-------------------+-------------+
label MAC address was found in factory at 0x165 (text format
xx:xx:xx:xx:xx:xx).

Notes
-----
[1] WAN MAC address:
   a. First octet of WAN MAC is differ than others and OUI is not related
      to TP-Link company. This probably should be fixed.
   b. Flipping bits in first octet and hex delta are different for the
      different MAC examples:
      +-----------------+----------------+----------------+
      |                 | Example 1      | Example 2      |
      +-----------------+----------------+----------------+
      | LAN             | 68 = 0110 1000 | 50 = 0101 0000 |
      | MAC (1st octet) |         ^ ^ ^  |                |
      +-----------------+----------------+----------------+
      | WAN             | 72 = 0111 0010 | 54 = 0101 0100 |
      | MAC (1st octet) |         ^ ^ ^  |            ^   |
      +-----------------+----------------+----------------+
      | HEX delta       | 0xa            | 0x4            |
      +-----------------+----------------+----------------+
      | DEC delta       | 4              | 4              |
      +-----------------+----------------+----------------+
   c. DEC delta is a constant (4). This looks like a mistake in OEM
      firmware and probably should be fixed.
   Based on the above, I decided to keep correct OUI and make WAN MAC =
   label + 1.

[2] Bootloaders
   The device contains 3 bootloaders:
   - First U-Boot: U-Boot 1.1.3 (Mar 18 2019 - 12:50:24). The First U-Boot
     located on NAND Flash to load next full-feature Uboot.
   - Main U-Boot + its backup: U-Boot 1.1.3 (Mar 18 2019 - 12:50:29). This
     bootloader includes recovery webserver. Requires special uImages to
     continue the boot process:
        0x00 (os0, os1) - firmware uImage
        0x40 (os0, os1) - standalone uImage (OpenWrt kernel is here)
   - Additionally, both slots of the original TP-Link firmware contains
     Image U-Boot: U-Boot 1.1.3 (Oct 16 2019 - 08:14:45). It checks image
     magics and CRCs. We don't use this U-Boot with OpenWrt.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2023-01-14 18:36:33 +01:00
Nick Hainke
c051693ef4 trace-cmd: update to v3.1.6
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 22:02:20 +01:00
Nick Hainke
d649c32989 libtracefs: update to 1.6.4
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 22:02:20 +01:00
Nick Hainke
d1bdf5a9d9 libtraceevent: update to 1.7.1
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-13 22:02:20 +01:00
Daniel Golle
3d5c5427e1 uboot-mediatek: update to U-Boot 2023.01
Support for MT7981 and MT7986 has been merged, remove patches.
Tested on a couple of MT7986, MT7622 and MT7623 boards.
MIPS builds are untested.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2023-01-13 14:49:52 +00:00
Linhui Liu
5b605f4b51 uboot-envtools: update to 2023.01
Update to latest version.

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
2023-01-13 14:49:52 +00:00
Robert Marko
c83dbcdf8f
mac80211: ath11k: fix monitor bringup
Currently, ath11k will crash the crash if we try to bringup the monitor
mode interface.
Luckily, it has already been fixed upstream, so backport the patches
fixing it.

Fixes: 93ae4353cd ("mac80211: add ath11k PCI support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2023-01-12 15:17:18 +01:00
Christian Marangi
d9aa41dcda
lldpd: use release tar instead of codeload
There is currently a problem with making reproducible version of lldpd.
The tool version is generated based on 3 source:
1. .dist-version file in release tar
2. git hash with presence of .git directory
3. current date

Using the codeload tar from github results in getting the repo without
the .git directory and since they are not release tar, we don't have
.dist-version. This results in having lldpd bin with a version set to
the current build time.

Switch to release tar so that we correctly have a .dist-version file and
the version is not based on the build time.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2023-01-12 14:55:07 +01:00
Hauke Mehrtens
76c67fcc66 ksmbd: Fix ZDI-CAN-18259
This fixes a security problem in ksmbd. It currently has the
ZDI-CAN-18259 ID assigned, but no CVE yet.

Backported from:
8824b7af40
cc4f3b5a6a

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-11 22:07:51 +01:00
Christian Marangi
ee397759b6
iwinfo: update to latest Git HEAD
c7b420a devices: add Qualcomm Atheros QCN6024/9024/9074 cards
5914d71 iwinfo: devices: add Qualcomm Atheros IPQ8074 WiSoC

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2023-01-10 00:54:31 +01:00
Felix Fietkau
0cc1c302b1 ucode-mod-bpf: add new package for a ucode libbpf binding
The bpf plugin provides functionality for loading and interacting with
eBPF modules.

It allows loading full modules and pinned maps/programs and supports
interacting with maps and attaching programs as tc classifiers.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-09 11:35:20 +01:00
Felix Fietkau
d6a284e4ce ucode: update to the latest version
34cfbb922c96 README.md: various spelling and documentation fixes
ff32355ea645 build: make rtnl/nl80211 depend on linux instead of !APPLE
c0e413c21f7b include: add uc_fn_thisval()
1e4d20932646 Merge pull request #134 from nbd168/thisval

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-09 11:35:20 +01:00
Hauke Mehrtens
25223b22c8 rtl8812au-ct: Ignore address errors
GCC 12.2.0 shows these error messages:
````
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c: In function 'rtw_mfree_stainfo':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:210:24: error: the comparison will always evaluate as 'true' for the address of 'lock' will never be NULL [-Werror=address]
  210 |         if(&psta->lock != NULL)
      |                        ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:109,
                 from rtl8812au-ct-2021-11-07-39df5596/core/rtw_sta_mgt.c:22:
rtl8812au-ct-2021-11-07-39df5596/include/sta_info.h:95:17: note: 'lock' declared here
   95 |         _lock   lock;
      |                 ^~~~
````

````
  CC [M]  rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.o
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c: In function 'cfg80211_rtw_scan':
rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:2176:32: warning: the comparison will always evaluate as 'true' for the address of 'ssid' will never be NULL [-Waddress]
 2176 |                 if(ssids->ssid != NULL
      |                                ^~
In file included from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service_linux.h:88,
                 from rtl8812au-ct-2021-11-07-39df5596/include/osdep_service.h:41,
                 from rtl8812au-ct-2021-11-07-39df5596/include/drv_types.h:32,
                 from rtl8812au-ct-2021-11-07-39df5596/os_dep/linux/ioctl_cfg80211.c:22:
/home/hauke/openwrt/openwrt/staging_dir/target-mips_24kc_musl/usr/include/mac80211/net/cfg80211.h:2364:12: note: 'ssid' declared here
 2364 |         u8 ssid[IEEE80211_MAX_SSID_LEN];
      |            ^~~~
````

````
  CC [M]  rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.o
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c: In function 'phydm_cmd_parser':
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:873:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
  873 |                         if(input[i+1]) {
      |                            ^~~~~
rtl8812au-ct-2021-11-07-39df5596/hal/OUTSRC/phydm_debug.c:894:28: warning: the comparison will always evaluate as 'true' for the pointer operand in 'input + ((sizetype)i + 1) * 16' must not be NULL [-Waddress]
  894 |                         if(input[i+1]) {
      |                            ^~~~~
````

This one was only seen on the rockchip/armv8 target:
````
  CC [M]  rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.o
In function '__nat25_add_pppoe_tag',
    inlined from 'nat25_db_handle' at rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:909:10:
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:118:9: error: 'memcpy' reading between 2052 and 9220 bytes from a region of size 40 [-Werror=stringop-overread]
  118 |         memcpy((unsigned char *)ph->tag, tag, data_len);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c: In function 'nat25_db_handle':
rtl8812au-ct-2021-11-07-39df5596/core/rtw_br_ext.c:878:63: note: source object 'tag_buf' of size 40
  878 |                                                 unsigned char tag_buf[40];
      |                                                               ^~~~~~~
````

Most of them are looking like real errors to me, but some fixes need a
deeper understanding of the driver and probably bigger changes to the driver.

Ignore these error messages for now. It would be nice if someone would
fix them.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-09 00:23:22 +01:00
Hauke Mehrtens
dc12c76dc5 uqmi: Ignore wrong maybe-uninitialized and dangling-pointer error
GCC 12.2.0 shows this false positive error message:
````
uqmi-2022-05-04-56cb2d40/dev.c: In function 'qmi_request_wait':
uqmi-2022-05-04-56cb2d40/dev.c:217:23: error: storing the address of local variable 'complete' in '*req.complete' [-Werror=dangling-pointer=]
  217 |         req->complete = &complete;
      |         ~~~~~~~~~~~~~~^~~~~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'complete' declared here
  208 |         bool complete = false;
      |              ^~~~~~~~
uqmi-2022-05-04-56cb2d40/dev.c:208:14: note: 'req' declared here
cc1: all warnings being treated as errors
````

and this one:
````
In file included from uqmi-2022-05-04-56cb2d40/commands.c:28:
In function 'blobmsg_close_table',
    inlined from 'cmd_nas_get_cell_location_info_cb' at /home/haukeuqmi-2022-05-04-56cb2d40/commands-nas.c:897:4:
/usr/include/libubox/blobmsg.h:256:9: error: 'c' may be used uninitialized [-Werror=maybe-uninitialized]
  256 |         blob_nest_end(buf, cookie);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from uqmi-2022-05-04-56cb2d40/commands.c:169:
uqmi-2022-05-04-56cb2d40/commands-nas.c: In function 'cmd_nas_get_cell_location_info_cb':
uqmi-2022-05-04-56cb2d40/commands-nas.c:713:15: note: 'c' was declared here
  713 |         void *c, *t, *cell, *freq;
      |               ^
cc1: all warnings being treated as errors
````

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-09 00:10:52 +01:00
Hauke Mehrtens
2748c45d46 elfutils: Ignore wrong use-after-free error
GCC 12.2.0 shows this false positive error message:
````
In function 'bigger_buffer',
    inlined from '__libdw_gunzip' at gzip.c:374:12:
gzip.c:96:9: error: pointer may be used after 'realloc' [-Werror=use-after-free]
   96 |     b = realloc (state->buffer, more -= 1024);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
gzip.c:94:13: note: call to 'realloc' here
   94 |   char *b = realloc (state->buffer, more);
      |             ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
````

GCC bug report: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=104069

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-09 00:10:52 +01:00
Hannu Nyman
98b09ba250 busybox: update to 1.36.0
Update busybox to version 1.36.0

* refresh patches (remove the backported upstream fix)
* refresh config

Config refresh:

Refresh commands, run after busybox is first built once:

cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0/.config > Config-defaults.in

Manual edits needed after config refresh:

* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
  BUSYBOX_DEFAULT_FEATURE_IPV6

* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
  BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)

* Config-defaults.in: OpenWrt logic applied to
  BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)

* Config-defaults.in: correct the default ports that get reset
  BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT    80
  BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT  23

* config/editors/Config.in: Add USE_GLIBC dependency to
  BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)

* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
  SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
  (discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
  Apparently our script does not see the hidden option while
  prepending config options with "BUSYBOX_CONFIG_" which leads to a
  missed dependency when the options are later evaluated.)

* Edit a few Config.in files by adding quotes to sourced items in
  config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2023-01-07 17:22:54 +01:00
Linhui Liu
9ee12db67c util-linux: update to 2.38.1
Release Notes:
    https://cdn.kernel.org/pub/linux/utils/util-linux/v2.38/v2.38.1-ReleaseNotes

Remove upstreamed:
- 010-meson-typo.patch
- 020-meson-fix-compilation-without-systemd.patch
- 110-meson-fix-when-HAVE_CLOCK_GETTIME-is-set.patch

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
2023-01-07 17:18:41 +01:00
Shiji Yang
9a07895729 mt76: add stand-alone MT7622 firmware package
Add a separate firmware package to avoid installing the MT7615 firmware
on all MT7622 target devices by default. Now we only add MT7615 firmware
packages for devices that use MT7615E. This commit also removes the
explicit dependency on kmod-mt7615e to refine the package dependency.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
fc9dd3f083 mt76: add stand-alone MT7915 firmware package
The mt7915e driver supports MT7915, MT7916 and MT7986 chips. And Only
MT7915 series chips need the MT7915 firmware. To save storage, extract
them from the common code package and create a new package to provide
the firmware.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
Shiji Yang
3410f010a2 mt76: remove unnecessary dependency from mt7915e
The kmod-mt7615-common package does not contain any code that
related to mt7915e Wi-Fi6 driver, so remove it.

Tested on ramips/mt7621: SIM SIMAX1800T

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2023-01-07 17:11:00 +01:00
David Bauer
f97ce066a8 zyxel-bootconfig: clean up script
Drop unused variable and fix identation.

Signed-off-by: David Bauer <mail@david-bauer.net>
2023-01-07 01:32:58 +01:00
Nick Hainke
5809fb4546 tcpdump: update to 4.99.2
Update to latest version. For release information look into CHANGES
file [0].

Automatically refreshed:
- 001-remove_pcap_debug.patch

Manually refreshed:
- 100-tcpdump_mini.patch

old ipkg sizes:
316554 bin/packages/mips_24kc/base/tcpdump_4.99.1-1_mips_24kc.ipk
141457 bin/packages/mips_24kc/base/tcpdump-mini_4.99.1-1_mips_24kc.ipk

new ipkg sizes:
318089 bin/packages/mips_24kc/base/tcpdump_4.99.2-1_mips_24kc.ipk
141941 bin/packages/mips_24kc/base/tcpdump-mini_4.99.2-1_mips_24kc.ipk

[0] - https://github.com/the-tcpdump-group/tcpdump/blob/master/CHANGES

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-06 16:22:28 +01:00
Nick Hainke
acbae4f234 libpcap: update to 1.20.2
A huge rewrite in libpcap was introduced by dc14a7babca1 ("rpcap: have
the server tell the client its byte order.") [0]. The patch
"201-space_optimization.patch" does not apply at all anymore. So remove
it.

Refresh:
- 100-no-openssl.patch
- 102-skip-manpages.patch

Update the "300-Add-support-for-B.A.T.M.A.N.-Advanced.patch" with latest
PR [1].

old ipkg size:
90964 bin/packages/mips_24kc/base/libpcap1_1.10.1-5_mips_24kc.ipk

new ipkg size:
93340 bin/packages/mips_24kc/base/libpcap1_1.10.2-1_mips_24kc.ipk

[0] - dc14a7babc
[1] - https://github.com/the-tcpdump-group/libpcap/pull/980

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-06 16:20:06 +01:00
Nick Hainke
b331ffe807 nftables: update to 1.0.6
Remove upstreamed patches:
- 0001-fix-nft.patch

Upstream switched to "tar.xz" archives.

old ipkg size:
273678 bin/packages/mips_24kc/base/nftables-json_1.0.5-2_mips_24kc.ipk

new ipkg size:
271624 bin/packages/mips_24kc/base/nftables-json_1.0.6-1_mips_24kc.ipk

Release Information:
https://netfilter.org/projects/nftables/files/changes-nftables-1.0.6.txt

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-06 16:14:45 +01:00
Michael Pratt
1e3a8f454e base-files: rework mtd_get_mac_text()
It's necessary to be able to specify the length
for MAC addresses that are stored in flash, for example,
in a case where it is stored without any delimiter.

Let both offset and length have default values.

Add a sanity check related to partition size.

Also, clean up syntax and unnecessary lines.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2023-01-06 15:34:07 +01:00
Linhui Liu
87b9825521 ncurses: update to 6.4
Update to the latest released version.

Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
2023-01-05 00:11:53 +01:00
Nikolay Martynov
665c2154ef ramips: add basic support for tp-link er605-v2
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
The board has headers to attach console. In order for them to work two solder
bridges near those pads need to be made.

The defice has the following partition table:

```
0x000000000000-0x000000080000 : "u-boot"
0x000000080000-0x000000100000 : "u-boot-env"
0x000000100000-0x000000140000 : "factory"
0x000000140000-0x000007e00000 : "firmware"
0x000007e00000-0x000008000000 : "panic-ops"
```

`firmware` partition contains UBI volumes. Unfortunately I accidentally wiped
partition and I no longer have access to it.

`firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot.
It also contains various configuration partitions that include device info and
MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes.

U-boot has `mtkupgrade` command that just overrides data on firmware partitions.
Firmware file provided by TP-Link cannot be used with that command.

U-boot also has 'recovery' http server. Unfortunately I was not able to make it
work with manufacturer's firmware.

Manufacturer's firmware essentially contains multiple UBI volumes along with
'partition table'. Unfortunately I no longer can properly run manufacturer's
firmware so I cannot at the moment try to a support for building 'factory' images.

This patch adds support for initramfs image as well as sysupgrade image.

This seems to be pretty standard MT7621 board otherwise.

Things that work:
* network
* leds
* usb
* factory MAC detection

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
2023-01-04 23:19:19 +01:00
Felix Fietkau
4455ed65c6 bridger: update to the latest version
def7755c459d add missing copyright headers
f68307fd96d7 add hairpin mode support
9ee8f433ba4e nl: do not pass NDA_VLAN with vid=0
978c1f9eed07 add support for the bridge port isolated flag

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2023-01-03 13:28:47 +01:00
Hauke Mehrtens
ee47a28cec treewide: Trigger reinstall of all wolfssl dependencies
The ABI of the wolfssl library changed a bit between version 5.5.3 and
5.5.4. This release update will trigger a rebuild of all packages which
are using wolfssl to make sure they are adapted to the new ABI.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2023-01-01 21:06:54 +01:00
Nick Hainke
04634b2d82 wolfssl: update to 5.5.4-stable
Remove upstreamed:
- 001-Fix-enable-devcrypto-build-error.patch

Refresh patch:
- 100-disable-hardening-check.patch

Release notes:
https://github.com/wolfSSL/wolfssl/releases/tag/v5.5.4-stable

Signed-off-by: Nick Hainke <vincent@systemli.org>
2023-01-01 21:05:31 +01:00
Hauke Mehrtens
55d176fd0b tfa-layerscape: Use trusted-firmware-a.mk
This converts the trusted firmware arm build Makefile to make use of
the common trusted-firmware-a.mk file. This also fixes the build with
binutils 2.39.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 20:02:09 +01:00
Hauke Mehrtens
c5bb7a99a6 arm-trusted-firmware-mvebu: Use host flags for cryptest compilation
Without these changes it used the system LDFLAGS for the compilation of
the cryptopp library. This does not always work when we add
"-no-warn-rwx-segments" which is done to support binutils 2.39 inside of
OpenWrt.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 19:55:42 +01:00
Hauke Mehrtens
dd9d1a8ccb arm-trusted-firmware-sunxi: Use common trusted-firmware-a.mk
Make use of the definitions from trusted-firmware-a.mk to build the
Trusted firmware arm. This fixes the build with binutils 2.39.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 19:03:00 +01:00
Tony Ambardar
9cbc825b30 base-files: stage2: add 'tail' to sysupgrade environment
This is used to access footer data in firmare files, and is simpler and
less error-prone than using 'dd' with calculated offsets.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Tony Ambardar
2a9f3b7717 ipq40xx: fix up Linksys WHW01 board name, device definition
Update the board name defined in DTS to match online documentation and the
name encoded into factory firmware. This helps supports flashing firmware
factory images using 'sysupgrade'.

Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB
instead of the correct 74 MB, and defines factory images which include
extra adjustments/padding that do not match OEM factory images and may
cause problems flashing. Update image size and build recipe to fix these.

Suggested-by: Wyatt Martin <wawowl@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2022-12-31 05:02:38 -08:00
Hauke Mehrtens
af3c9b74e1 mbedtls: update to version 2.28.2
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.2
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.

Fixes the following CVEs:
* CVE-2022-46393: Fix potential heap buffer overread and overwrite in
DTLS if MBEDTLS_SSL_DTLS_CONNECTION_ID is enabled and
MBEDTLS_SSL_CID_IN_LEN_MAX > 2 * MBEDTLS_SSL_CID_OUT_LEN_MAX.

* CVE-2022-46392: An adversary with access to precise enough information
about memory accesses (typically, an untrusted operating system
attacking a secure enclave) could recover an RSA private key after
observing the victim performing a single private-key operation if the
window size used for the exponentiation was 3 or smaller.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-31 03:19:58 +01:00
Felix Fietkau
12fdb4c9f4 mac80211: fix receiving multicast packets on multiple sta interfaces
Also fix MLO sta sdata link initialization

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-30 21:20:04 +01:00
Felix Fietkau
2e61469a6c netifd: update to the latest version
2cffe0c44e62 treewide: correctly apply IFNAMSIZ limit
96bcbb2e4eb6 wireless: allow set_retry ubus notify command to trigger a wdev restart
a2e8cd75dbf6 wireless: add support for disabling multicast-to-unicast per virtual interface
e9f44189ade7 system: move netdev types to system-linux.c where they are used
a3fab0119ef1 utils: include utils.h last
7ce73fc16765 vlandev: propagate topology changes
81c1fbcba2f2 device: fix vlan device issues with disappearing lower devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-30 16:42:57 +01:00
Chuanhong Guo
d29dbf052a
mediatek: drop redmi-ax6000 variant with modified env
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-30 16:11:59 +08:00
Hauke Mehrtens
f12bad6c19 tree-wide: Do not use package librt and libpthread
The libraries libpthread, libdl, libutil, libanl have been integrated
into the libc library in version 2.34. it is not needed to explicitly
link them any more.

Most of the functions have been moved from the librt.so into libc.so
some time ago already.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-29 18:50:24 +01:00
Robert Marko
9d8eff6799
linux-firmware: disable stripping
It has been brought to my attention that recently added WCN6855 firmware
is broken as it is getting stripped during building due to being 2 ELF
binaries.
I am sure WCN6750 and any other ELF binaries are having the same issue,
so since stripping firmware binaries is clearly unwanted disable it.

Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-29 14:15:55 +01:00
Furong Xu
1613e3340b uboot-mediatek: add support for Xiaomi Redmi Router AX6000
U-Boot flash instructions:

0. OpenWrt U-Boot does not support stock layout, it comes with recovery
boot support, automatic tftp recovery and never blocks UART.

A new flash layout is introduced, we call it OpenWrt U-Boot layout,
stock flash layout and the old OpenWrt layout are not supported.

During the whole flash procedure, please do not reboot or power off
unless requested explicitly, or you will break your device.

1. Your device should already running OpenWrt.
If not, follow the instructions to flash OpenWrt:
https://github.com/openwrt/openwrt/pull/11115

2. Backup BL2 Nvram Bdata Factory and FIP in case you break something or
in case you want to go back to stock firmware one day.

cat /dev/mtdblock0 > /tmp/BL2.bin
cat /dev/mtdblock1 > /tmp/Nvram.bin
cat /dev/mtdblock2 > /tmp/Bdata.bin
cat /dev/mtdblock3 > /tmp/Factory.bin
cat /dev/mtdblock4 > /tmp/FIP.bin

And save all whose bin files to somewhere safe.

Then backup your configurations, since ubiformat for entire mtd device is
required to create new ubootenv volume for OpenWrt U-Boot.

3. Run the following cmd to boot into an initramfs with the new OpenWrt
U-Boot layout that expand ubi partion to the end of flash:

ubiformat /dev/mtd7 -y -f /tmp/ax6000-ubootmod-initramfs-factory.ubi

4. After boot into initramfs, check mtd partion info.
The ubi partion should be mtd5

root@OpenWrt:~# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00020000 BL2
mtd1: 00040000 00020000 Nvram
mtd2: 00040000 00020000 Bdata
mtd3: 00200000 00020000 Factory
mtd4: 00200000 00020000 FIP
mtd5: 07a80000 00020000 ubi

5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.

To install kmod-mtd-rw via opkg:

opkg update && opkg install kmod-mtd-rw

Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.

Load kmod-mtd-rw:
insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1

6. Run the following cmd to clean all pending crash dumps in pstore,
or OpenWrt U-Boot may boot into NAND recovery or tftp recovery.

rm -f /sys/fs/pstore/*

7. Format ubi and create new ubootenv volume:

ubidetach -p /dev/mtd5; ubiformat /dev/mtd5 -y; ubiattach -p /dev/mtd5
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB

8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.

ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/ax6000-ubootmod-initramfs-recovery.itb

9. Now, flash new U-Boot. Bye-bye ugly stock U-Boot.

mtd write /tmp/ax6000-ubootmod-preloader.bin BL2
mtd write /tmp/ax6000-ubootmod-bl31-uboot.fip FIP

10. Flash the squashfs-sysupgrade.bin as usual:

sysupgrade -n /tmp/ax6000-ubootmod-squashfs-sysupgrade.itb

Enjoy!

Signed-off-by: Furong Xu <xfr@outlook.com>
2022-12-29 03:04:42 +00:00
Robert Marko
214c230a79 linux-firmware: ath11k: add symlink for WCN6855 hw2.1
WCN6855 exists in 2 HW revisions, but both use the same FW so upstream
just has a symlink for hw2.1 to hw2.0 that I forgot to make.

Fixes: b4d3694f81 ("linux-firmware: package ath11k consumer cards firmware")
Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-28 21:57:05 +01:00
Nick Hainke
4f44b4e506 linux-firmware: update to 20221214
Changes:
f3c283e amdgpu: updated navi10 firmware for amd-5.4
ba115d4 amdgpu: updated yellow carp firmware for amd-5.4
b8aba70 amdgpu: updated raven2 firmware for amd-5.4
2b21c5e amdgpu: updated raven firmware for amd-5.4
fc9a1c9 amdgpu: updated PSP 13.0.8 firmware for amd-5.4
7d43336 amdgpu: updated GC 10.3.7 RLC firmware for amd-5.4
c089dab amdgpu: updated vega20 firmware for amd-5.4
75e3494 amdgpu: updated PSP 13.0.5 firmware for amd-5.4
31c5734 amdgpu: add VCN 4.0.0 firmware for amd-5.4
a735158 amdgpu: add SMU 13.0.0 firmware for amd-5.4
0bef6bb amdgpu: Add SDMA 6.0.0 firmware for amd-5.4
bb56d1a amdgpu: add PSP 13.0.0 firmware for amd-5.4
e32209f amdgpu: add GC 11.0.0 firmware for amd-5.4
613db81 amdgpu: add DCN 3.2.0 firmware for amd-5.4
1fc8f6c amdgpu: updated vega10 firmware for amd-5.4
2257447 amdgpu: updated beige goby firmware for amd-5.4
6aa0023 amdgpu: updated dimgrey cavefish firmware for amd-5.4
dd1225a amdgpu: updated vangogh firmware for amd-5.4
5cb010e amdgpu: updated picasso firmware for amd-5.4
edf9699 amdgpu: updated navy flounder firmware for amd-5.4
b7e83d9 amdgpu: updated green sardine firmware for amd-5.4
f820cc3 amdgpu: updated sienna cichlid firmware for amd-5.4
b77f539 amdgpu: updated arcture firmware for amd-5.4
dccfdf1 amdgpu: updated navi14 firmware for amd-5.4
5d1af6d amdgpu: updated renoir firmware for amd-5.4
13b9c94 amdgpu: updated navi12 firmware for amd-5.4
e9b8357 amdgpu: updated aldebaran firmware for amd-5.4
b4af754 sr150 : Add NXP SR150 UWB firmware
0707b2f brcm: add/update firmware files for brcmfmac driver
16c9630 rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x75b8_f098
80ed874 amdgpu: update sdma_5.2.7 firmware
32d8681 QCA: Add Bluetooth firmware for WCN785x This commit will add required Bluetooth firmware files for QCA WCN785x. The image version is 2.0.0-00515.
cdf9499 linux-firmware: update firmware for MT7916
685ea4d linux-firmware: update firmware for MT7915
7f6279b i915: Add DMC v2.08 for DG2
391fb47 amdgpu: update green sardine DMCUB firmware
de854c9 i915: Add DMC v2.10 for MTL
daff404 linux-firmware: update firmware for MT7986
70494e3 linux-firmware: update firmware for mediatek bluetooth chip (MT7921)
750c0dc linux-firmware: update firmware for MT7921 WiFi device

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-28 20:20:01 +01:00
Felix Baumann
75451681d0
uboot-envtools: add support for ramips Asus RX-AX53U
Adds uboot-envtools support for ramips Asus RX-AX53U now that partition
can be correctly read.

Signed-off-by: Felix Baumann <felix.bau@gmx.de>
[ improve commit title and description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-28 14:04:58 +01:00
Felix Fietkau
090ad03343 hostapd: allow sharing the incoming DAS port across multiple interfaces
Use the NAS identifier to find the right receiver context on incoming messages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-27 19:10:04 +01:00
Hauke Mehrtens
fb15cb4ce9 iproute2: Fix build with GCC 12 and glibc 2.36
This fixes the detection of name_to_handle_at() when GCC 12 and glibc
2.36 are used.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-26 15:18:08 +01:00
Hauke Mehrtens
73dca49f35 uhttpd: update to latest Git HEAD
2397755 client: fix incorrectly emitting HTTP 413 for certain content lengths

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-26 15:18:08 +01:00
Xuefer H
ab31547df0 libbsd: fix libpath to not use host path
libpath.so uses host path in ld script causing other packages fail to
cross compile, e.g. perl:
"ld: cannot find /usr/lib/libbsd.so.0.11.6: No such file or directory"

Fixes: openwrt/packages#19390

Signed-off-by: Xuefer H <xuefer@gmail.com>
2022-12-26 13:36:41 +01:00
Kevin Darbyshire-Bryant
5c7e4a9d2e dnsmasq: bump to v2.88
Most relevant feature for openwrt in this release, supports dynamically
removing hosts from 'hostsdir' supplied host files.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2022-12-25 15:07:36 +00:00
Kuan-Yi Li
a5f16b4f4f
uboot-omap: build with omap generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: b2bfea48 ("omap: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:54 +01:00
Kuan-Yi Li
808046b2ee
uboot-tegra: build with tegra generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: c028e1b1 ("tegra: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:53 +01:00
Kuan-Yi Li
64bfb8b7d6
uboot-zynq: build with zynq generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: 6d7129ef ("zynq: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:53 +01:00
Kuan-Yi Li
1c35dc26f1
uboot-mxs: build with mxs generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: 64ef920b ("mxs: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:52 +01:00
Kuan-Yi Li
5c85c1f344
uboot-kirkwood: build with kirkwood generic subtarget
Fix image build fail by using the generic subtarget.

Fixes: cada395a ("kirkwood: add generic subtarget")
Ref: 40e3f660 ("uboot-fritz4040: build with ipq40xx generic subtarget")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[ add commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-25 11:55:52 +01:00
Jan-Niklas Burfeind
c7d3bbb909 sunxi: ensure NanoPi R1 has unique MAC address
Ensure the MAC address for all NanoPi R1 boards is assigned uniquely for
each board.

The vendor ships the device in two variants; one with and one without
eMMC; but both without static mac-addresses.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S and R4S in case the EEPROM
chip is not present by generating the board MAC from the SD card CID.

[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R1#Hardware_Spec

Similar too and based on:

commit b5675f500d ("rockchip: ensure NanoPi R4S has unique MAC address")

Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-25 02:27:55 +01:00
Hauke Mehrtens
cb7d662dac mac80211: Do not build brcmsmac on bcm47xx_legacy
brcmsmac needs bcma. bcma is build into the kernel for the other bcm47xx
subtargets, but not for the legacy target because it only uses ssb. We
could build bcma as a module for bcm47xx_legacy, but none of these old
devices uses a wifi card supported by brcsmac.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-24 15:14:58 +01:00
Felix Fietkau
274dfcb19e mt76: update to the latest version
a03ef0aab93e wifi: mt76: mt7921: fix deadlock in mt7921_abort_roc
5b509e80384a wifi: mt76: dma: fix a regression in adding rx buffers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-22 16:19:55 +01:00
Jan-Niklas Burfeind
bf06a7c865 uboot-sunxi: use UUID of bootdev and bootpart
Several sunxi devices come with multiple mmc devices. On such devices,
the mmc device order is unpredictable, so using /dev/mmcblk0p2 as root
device doesn't always work, which results in unbootable devices.

For the Banana Pi BPI-R3 in the mediatek target, this has been solved by
defining aliases for the mmc devices in the DTS. Ideally we would do the
same here, but for sunxi-a64 we already use UUID probing, so let's start
with that (5f2ff607e2 ("uboot-sunxi: a64: allow booting directly from
eMMC")).

Since we're building and including u-boot in each supported device
image, and this method has been proven to work fine for a64, let's just
change the default u-boot env file to do the same.

Fixes: #10080
Fixes: e6d9f6fdff ("sunxi: add support for FriendlyARM NanoPi R1")
Co-authored-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
[use UUID in default u-boot env, rewrite commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-22 13:33:47 +02:00
Jan-Niklas Burfeind
5b82eeb320 sunxi: remove frequency for NanoPi R1
The frequency appears as unlisted initial frequency.
Removed it as Hauke suggested.

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-22 00:05:29 +01:00
Stijn Tintel
9ed1830bdc arm-trusted-firmware-sunxi: drop CPE ID
The CPE ID is already set in trusted-firmware-a.mk.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-20 18:36:26 +00:00
Daniel Golle
6675a9aaf4 xdp-tools: update to version 1.2.9
Changes since v1.2.8:
 32aaf32 libxdp: Fix incorrect rx_ring_setup_done
 6049671 headers: add bpf_endian.h for parsing_helpers.h
 2682c1c export-man: Ignore errors when executing git shell command
 8afda7a xdp-loader/README: Mention lack of support for HW mode in most cards
 dc69919 libxdp: fix prog_fd checks for fd >= 0
 3d7c22a libxdp: Allow falling back to single-program attachment for loaded programs
 af00429 libxdp: Fix check in xdp_program__attach_single()
 41703d2 libxdp: Make sure to set the the program autoload when loading a program
 b1fd2e5 test-xdpdump: Only run tshark attribute test on newer versions of tshark
 5dfe342 libxdp: Convert xdp-dispatcher to use strict section names
 929a22e configure: Try to auto-detect versioned clang binaries
 074fcfb libxdp: Check program name when determining if a program is a dispatcher
 e13a191 Bump TOOLS_VERSION to 1.2.9

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-20 13:57:34 +00:00
Rosen Penev
6d1df35747 hostapd: add mbedtls variant
This adds the current WIP mbedtls patches for hostapd. The motivation
here is to reduce size.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-12-19 12:27:35 +00:00
Robert Marko
93ae4353cd
mac80211: add ath11k PCI support
ath11k is the upstream driver for Qualcomm 802.11ax radios, both for the
internal AHB and PCI based cards.
This commit does however only provide PCI support while AHB will follow
but its SoC specific so it will require an OpenWrt target first.

It differs a bit from ath10k as it requires stuff like QRTR, MHI and QMI
helpers.

PCI variant requires qrtr-mhi and mhi-bus which backports do provide,
however we are dropping those in a patch as they will conflict with
support for the AHB variant as that one requires qrtr-smd which in turn
requires RPMSG and GLINK and its not feasable to provide those in
backports as they are really SoC specific.

QRTR and MHI in kernel 5.10 are not usable and backporting the changes
is not easy as they have changed drastically from 5.10 to 5.15 ath11k will
only be available on targets that use kernel 5.15.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-19 01:01:57 +01:00
Robert Marko
b4d3694f81
linux-firmware: package ath11k consumer cards firmware
Package firmware for ath11k supported QCA consumer cards from linux-firmware.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-19 01:01:57 +01:00
Robert Marko
5968290a21
kernel: package QRTR support
QRTR is Qualcomm IPC router protocol and ath11k requires it for both
AHB and PCI support, so package it as a kernel module so it can be
added as a dependency to the ath11k module.

Only kernel 5.15 is currently supported due to various things missing in
5.10 whose backporting is out of scope for this patch.

SMD, TUN and MHI variants are packaged.

SMD variant depends on the ipq807x
target as it has dependency on the RPMSG drivers which are Qualcomm
and SoC specific anyway.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2022-12-19 01:01:52 +01:00
Nick Hainke
8ed53e0928 iproute2: update to 6.1.0
Announcement:
https://lore.kernel.org/netdev/20221214094130.7b11ec2e@hermes.local/T/#t

Refresh patch:
- 170-ip_tiny.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-18 16:33:16 +01:00
Alexey Bartenev
3f201d1f8e ramips: add support for SNR-CPE-W4N-MT router
General specification:
- SoC Type: MediaTek MT7620N (580MHz)
- ROM: 8 MB SPI-NOR (W25Q64FV)
- RAM: 64 MB DDR (M13S5121632A)
- Switch: MediaTek MT7530
- Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
- Wireless 2.4 GHz: b/g/n
- Buttons: 1 button (RESET)
- Bootloader: U-Boot 1.1.3, MediaTek U-Boot: 5.0.0.5
- Power: 12 VDC, 1.0 A

Flash by the native uploader in 2 stages:
1. Use the native uploader to flash an initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-initramfs-kernel.bin file by
 "Administration/Management/Firmware update/Choose File" in vendor's
 web interface (ip: 192.168.1.10, login: Admin, password: Admin).
 Wait ~160 seconds.
2. Flash a sysupgrade image via the initramfs image. Choose
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 file by "System/Backup/Flash Firmware/Flash image..." in
 LuCI web interface (ip: 192.168.1.1, login: root, no password).
 Wait ~240 seconds.

Flash by U-Boot TFTP method:
1. Configure your PC with IP 192.168.1.131
2. Set up TFTP server and put the
 openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
 image on your PC
3. Connect serial port (57600 8N1) and turn on the router.
 Then interrupt "U-Boot Boot Menu" by hitting 2 key (select "2:
 Load system code then write to Flash via TFTP.").
Press Y key when show "Warning!! Erase Linux in Flash then burn
 new one. Are you sure? (Y/N)"
Input device IP (192.168.1.1) ==:192.168.1.1
Input server IP (192.168.1.131) ==:192.168.1.131
Input Linux Kernel filename () ==:
openwrt-ramips-mt7620-snr_cpe-w4n-mt-squashfs-sysupgrade.bin
3. Wait ~120 seconds to complete flashing

Signed-off-by: Alexey Bartenev <41exey@proton.me>
2022-12-17 22:34:44 +01:00
Hauke Mehrtens
a442974cfa gdb: Do not link against xxhash
libxxhash is now available in the OpenWrt package feed and gdb will link
against it if gdb finds this library. Explicitly deactivate the usage
of xxhash.

This should fix the build of gdb in build bots.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-17 22:34:44 +01:00
Chukun Pan
53123b93b0 sunxi: fix board_name for MarsBoard A10
The compatible in the device tree is "haoyu,a10-marsboard",
modify the board_name to keep it consistent.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-12-17 20:55:47 +01:00
Nick Hainke
74b7d69601 strace: update to 6.1
Release Notes:
https://github.com/strace/strace/releases/tag/v6.1

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:28:18 +01:00
Nick Hainke
95ed519b25 trace-cmd: update to v3.1.5
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:24:46 +01:00
Nick Hainke
b5d317f47e libtracefs: update to 1.6.3
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:24:46 +01:00
Nick Hainke
b01f2d9f38 libtraceevent: update to 1.7.0
Update to latest release.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-17 20:24:46 +01:00
Hauke Mehrtens
243a7256c1 kernel: Make use of KERNEL_MAKE
Make use of KERNEL_MAKE in kernel packages were easily possible.
This moves some more code to common places and reduces the number of
lines.

It is defined like this:
KERNEL_MAKE = $(MAKE) $(KERNEL_MAKEOPTS)
KERNEL_MAKEOPTS = -C $(LINUX_DIR) $(KERNEL_MAKE_FLAGS)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-17 20:12:31 +01:00
Chen Minqiang
18bea173a6 mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.

1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
   stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
   to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
   be helpful for users who may forget to do this before sysupgrade in
   the initramfs.

New flash instructions:
1. Gain ssh access. Please refer to:
   https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)

2. Check which system current u-boot is loading from:
   COMMAND: `cat /proc/cmdline`
   sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
   if firmware=1, current system is ubi1
   if firmware=0, current system is ubi0

3. Setup nvram and write the firmware:
   If the current system is ubi1, please set it up so that the next time
   it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
   If the current system is ubi, please set it up so that the next time
   it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```

4. After rebooting, the system should now boot into the openwrt initramfs.
   Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.

For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:

1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```

2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:04:16 +08:00
Chuanhong Guo
189637c964 base-files: sysupgrade-tar: allow separated kernel/rootfs ubi
There are some devices putting kernel and rootfs on separated
ubi volumes. To make OpenWrt compatible with their bootloader,
we need to put kernel and rootfs into separated ubi volumes.
Add support for CI_KERN_UBIPART and CI_ROOT_UBIPART for this
situation.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 14:08:58 +08:00
Chuanhong Guo
c48e511fef base-files: split ubi attaching out of nand_upgrade_prepare_ubi
split ubi reformat/attach into nand_attach_ubi in preparation
for reusing this code in other functions.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 14:08:58 +08:00
Chuanhong Guo
9e2c01e4a6
kernel: add driver package for WS2812B LEDs
Two WS2812B (NeoPixel) clones are used in Xiaomi Redmi AX6000 as
indicator lights. Add a driver for controlling it using SPI MOSI.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:41:57 +08:00
Felix Fietkau
d07d47d0e3 mac80211: fix a regression in processing management frames for AP VLAN interfaces
Fixes re-assoc of WDS stations

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
581f2b15b2 hostapd: enable coredumps
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
c2fde432b3 hostapd: always set a default for the nas identifier
It is used for both 802.11r and WPA enterprise.
Setting it when not needed is harmless

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
133a1e2f37 mac80211: work around a race condition on detecting a phy while bringing it up
When reloading modules and running wifi, a phy can sometimes be renamed
while in the middle of a hotplug call that tries to detect new phys
This can lead to bogus wifi-device sections being created

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
92acd9f3e8 mac80211: fix uninitialized variable in rx->link/link_sta initialization fix
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Felix Fietkau
2fb38b77a2 hostapd: add support for automatically setting RADIUS own-ip dynamically
Some servers use the NAS-IP-Address attribute as a destination address

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-16 14:32:47 +01:00
Jo-Philipp Wich
d15b1fbed7 rpcd: update to latest Git HEAD
7de4820 iwinfo: add "hwmodes_text" to the info output
b3f530b iwinfo: clean up rpc_iwinfo_call_hw_ht_mode()
c46ad61 iwinfo: reuse infos provided by libiwinfo
6c5e900 iwinfo: constify string map arg for rpc_iwinfo_call_int()

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-12-16 00:55:51 +01:00
Jo-Philipp Wich
4a4d0bf78d iwinfo: update to latest Git HEAD
8d15809 cli: print current HT mode
8f86dd6 cli: use IWINFO_HTMODE_COUNT
f36b72b cli: use IWINFO_KMGMT_NAMES
91be7e0 cli: use IWINFO_CIPHER_NAMES
49b6ec9 cli: fix printing the scan channel width
b1c8873 cli: fix marking the active channel
9e14e64 utils: add iwinfo_band2ghz() and iwinfo_ghz2band() helpers
e084781 utils: add helper functions to get names by values
d09a77a utils: add iwinfo_htmode_is_{ht|vht|he} helpers
8752977 utils: add and use iwinfo_format_hwmodes()
02f433e lib: add IWINFO_80211_COUNT and IWINFO_80211_NAMES
1d30df1 lib: add IWINFO_BAND_COUNT and IWINFO_BAND_NAMES
aefd0ef lib: use common IWINFO_CIPHER_NAMES strings
a5b30de lib: add IWINFO_OPMODE_COUNT and use it for IWINFO_OPMODE_NAMES
9f29e79 lib: constify and fixup the string array definitions
fddc015 nl80211: mark frequencies where HE operation in not allowed
6d50a7c nl80211: add support for HE htmodes
4ba5713 nl80211: properly get available bands for the hwmode
91b2ada nl80211: update the kernel header nl80211.h
3f619a5 nl80211: fix frequency/channel conversion for the 6G band
a77d915 nl80211: don't guess if a name is an ifname
c27ce71 devices: add usb device MediaTek MT7921AU
14f864e nl80211: add ability to describe USB devices
a5a75fd nl80211: remove ancient wpa_supplicant ctrl socket path
dd4e1ff nl80211: fix wpa supplicant ctrl socket permissions
d638163 fix -Wdangling-else warnings
4aa6c5a fix -Wreturn-type warning
3112726 fix -Wpointer-sign warning
ebd5f84 fix -Wmaybe-uninitialized warning
5469898 fix -Wunused-variable warnings
462b679 fix -Wduplicate-decl-specifier warnings
ccaabb4 fix -Wformat-truncation warnings
50380db enable useful compiler warnings via -Wall

Fixes: https://github.com/openwrt/openwrt/issues/10158
Fixes: https://github.com/openwrt/openwrt/issues/10687
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2022-12-16 00:55:51 +01:00
Felix Fietkau
b7a7a97037 mac80211: fix connecting multiple wds stations to an AP
A faulty check prevented the AP_VLAN interfaces from being brought up

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-14 13:54:02 +01:00
Linus Lüssing
26d10bad7c libpcap: add support for B.A.T.M.A.N. Advanced
This adds support for the layer 2 mesh routing protocol
B.A.T.M.A.N. Advanced. "batadv" can be used to filter on batman-adv
packets. It also allows later filters to look at frames inside the
tunnel when both "version" and "type" are specified.

Documentation for the batman-adv protocol can be found at the following
locations:

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/networking/batman-adv.rst
https://www.open-mesh.org/

--

This is a backport of the following upstream pull request:

https://github.com/the-tcpdump-group/libpcap/pull/980
-> "Add support for B.A.T.M.A.N. Advanced #980"

Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
2022-12-14 01:06:26 +01:00
Mikhail Zhilkin
0ec8d991c2 ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1.  Login to the router web interface under admin account
2.  Navigate to Settings -> Configuration -> Save to Computer
3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
       cfgtool.py -u configurationBackup.cfg
4.  Open configurationBackup.xml and find the following line:
    <PARAMETER name="Password" type="string" value="<your router serial \
       is here>" writable="1" encryption="1" password="1"/>
5.  Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml
7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router
8.  Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
    ETxxxxxxxxxx is the serial number from the backplate label)
9.  Navigate to Settings -> WAN -> Add static IP interface (e.g.
    10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
    10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
    ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
       sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
       printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
       reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 10.0.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:50    |
| WAN | label + 11 | *:5b    |
| 2g  | label + 2  | *:52    |
| 5g  | label + 3  | *:53    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-12-13 23:06:20 +01:00
Felix Fietkau
a4339c5a21 mac80211: add a fix for a crash in __ieee80211_rx_h_amsdu
Fix initialization of rx->link_sta

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-13 21:14:43 +01:00
Andre Heider
7c63295bf4 treewide: remove DRIVER_11N_SUPPORT
hostapd's compile time option CONFIG_IEEE80211N was removed almost 3 years
ago, 80.211n/HT is always included since then.

Noticed because `hostapd -v11n` confusingly returned an error.

See hostapd's commit:
f3bcd69603 "Remove CONFIG_IEEE80211N build option"

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-13 10:54:50 +01:00
Andre Heider
2d36f60d88 hostapd: fix 350-nl80211_del_beacon_bss.patch
Pass the expected struct:

../src/drivers/driver_nl80211.c: In function 'wpa_driver_nl80211_del_beacon':
../src/drivers/driver_nl80211.c:2945:31: warning: passing argument 1 of 'nl80211_bss_msg' from incompatible pointer type [-Wincompatible-pointer-types]
 2945 |         msg = nl80211_bss_msg(drv, 0, NL80211_CMD_DEL_BEACON);
      |                               ^~~
      |                               |
      |                               struct wpa_driver_nl80211_data *
../src/drivers/driver_nl80211.c:695:50: note: expected 'struct i802_bss *' but argument is of type 'struct wpa_driver_nl80211_data *'
  695 | struct nl_msg * nl80211_bss_msg(struct i802_bss *bss, int flags, uint8_t cmd)
      |                                 ~~~~~~~~~~~~~~~~~^~~

Fixes: 35ff1affe8 "hostapd: update to 2022-05-08"
Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-13 10:54:50 +01:00
Andre Heider
3bc060440a hostapd: remove an unused function from ubus.c
eee80211_frequency_to_channel() isn't used anymore, which is a leftover from:
2a31e9ca97 "hostapd: add op-class to get_status output"

Signed-off-by: Andre Heider <a.heider@gmail.com>
2022-12-13 10:54:50 +01:00
Felix Fietkau
e046500fe9 ath9k: add missing dependency on random core
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-13 10:25:27 +01:00
Christian Lamparter
19b3b14e54 sunxi: fix 253-sunxi-h5-add-support-for-nanopi-r1s-h5 patch offset
This showed up in the log:
|Hunk #1 succeeded at 555 (offset -83 lines).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Tony Butler
1e240f60a5 kernel: modules/lib-lz4: add lz4hc_compress
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config

this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor

Signed-off-by: Tony Butler <spudz76@gmail.com>
2022-12-11 09:32:53 -08:00
Felix Fietkau
03518a1b3a rtl8812au-ct: fix build with newer backports cfg80211 api
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-11 09:48:38 +01:00
Chukun Pan
171691500e wolfssl: fix build with /dev/crypto
Backport upstream patch to fix build error when
/dev/crypto enabled.

dc9f46a3be

Fixes: #10944
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-12-11 03:30:14 +01:00
Julio Gonzalez Gil
840ce0a65b umbim: Allow roaming and partner connections
Allow registration if the SIM is roaming or partner mode, by adding two
new options to the protocol.

Until now, such registration failed because umbim returns exit codes 4 and
5 for such situations.

Signed-off-by: Julio Gonzalez Gil <git@juliogonzalez.es>
2022-12-11 03:24:45 +01:00