During the last update to 12.5.r2 printing of the attached PHY-s was
removed, so lets bring it back as it is very helpfull for debugging
OpenWrt issues without users having to modify NSS-DP to know if a PHY
was attached.
Refresh patches since nss_dp_main.c was edited.
Link: https://github.com/openwrt/openwrt/pull/15537
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the RTL8723BE PCIe Wi-Fi Adapter by adding backports drivers
Signed-off-by: David Adriao <davidadriao@dglitch.com>
[Do not remove rtl8xxxu and add dependency to rtl8723be-firmware]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This makes the components used on the lantiq SoCs compile with kernel
6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[also fix ifxmips_ptm_adsl.c]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
gpio.h has been deprecated for a while and no longer compiles with 6.6.
Include the proper header.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15471
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, trying to compile qca-ssdk on macOS will fail in a weird way:
make[6]: *** No rule to make target 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/-n',
needed by 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/qca-ssdk.o'. Stop.
After looking looking at src_list.dep from which KBuild cmd_mod will
generate the list of objects to compile it looked like:
-n /src/adpt/adpt.c
-n
-n
Which was rather suspicous so after comparing to the same file but with
Fedora as host:
/src/adpt/adpt.c src/adpt/hppe/adpt_hppe_fdb.c src/adpt/hppe/adpt_hppe_mib.c
It was clear that echo -n which was used in SSDK-s target.mk was not
working as intented, and it looked like the POSIX only version of echo
was being used which does not honor -n.
So, after failling to reproduce it externally, replacing the call to echo
with a full path to coreutils echo fixed the compilation.
After further debugging, it was determined that SSDK does not honor
CONFIG_SHELL like other kernel modules so it was defaulting to /bin/sh as
the shell make was calling thus calling the /bin/sh built-in echo which on
macOS is the old Bash 3.2 one and it does not respect -n.
So, we have to explicitly pass SHELL=$(BASH) to SSDK to make it use bash
like kernel build or other kernel modules.
This is not an issue since on macOS we always build bash anyway.
Link: https://github.com/openwrt/openwrt/pull/15459
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux kernel commit torvalds/linux@b8a1a4cd5a
added a temporary probe_new member to struct i2c_driver, to drop the
rarely used second parameter of the probe function and not break API for
out of tree drivers. With torvalds/linux@5eb1e6e459,
which is part of v6.6, this probe_new member is dropped and the
signature of the probe function is updated.
ubnt-ledbar is used by the mediatek and ramips targets and both have
been updated to v6.6, so adapt the probe function signature and remove
other compat code for versions before v6.6.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: https://github.com/openwrt/openwrt/pull/15443
Signed-off-by: Robert Marko <robimarko@gmail.com>
This includes multiple updates for BCM2711 and BCM2712.
Full changelog:
0968de2871...1.20240424
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There is a new branch 12.5.r2 for kernel 6.6, so refresh
and update patches.
Delete patch 0010-nss-dp-include-net-netdev_rx_queue.h.patch
Changes:
2024-04-04 -5bf8b91 [qca-nss-dp] Adding support for port ID 3 & 4 in MHT switch
2024-03-28 -ce1e4cf [qca-nss-dp] Use skb_queue_head_init instead of __skb_queue_head_init.
2024-03-11 -0d26366 [qca-nss-dp] Read MHT LAN port status for ErP phase2
2024-03-22 -8382f14 [qca-nss-dp] Fix compilation issues seen on ginger branch for Miami profile
2023-05-02 -09b0983 [qca-nss-dp] vp list processing for capwap
2024-02-22 -bc09a01 [qca-nss-dp] EDMA ring reset for PPE-DS
2024-03-12 -2fcb586 [qca-nss-dp] Fix the EDMA clock frequency for the mitigation timer configuration
2024-02-23 -44ba1be [qca-nss-dp] Add API to retrieve ethernet netdevs for ErP
2024-02-09 -a5979b7 [qca-nss-dp] send napi and ip checksum for VP handler
2024-01-12 -1b9cb5d qca-nss-dp: User netdev_alloc_skb_fast instead of dev_alloc_skb
2024-01-08 -a859b48 [qca-nss-dp] NAPI Budget and EDMA Rx size change for KPI improvement.
2024-01-06 -8935523 [qca-nss-dp] Offload L3, L4 checksum to hardware for ppe-vp.
2023-12-07 -bbd9547 [qca-nss-dp] Fix Compilation issues on kernel6.6
2023-10-12 -bc55f75 [qca-nss-dp]: Enable legacy SCS for PPE-VP.
2023-09-08 -6bd771f [qca-nss-dp] Invalidate secondary descriptor before use.
2023-12-19 -b143df8 [qca-nss-dp] Fixed nss_dp_hal_hw_reset functionality for ipq53xx.
2023-12-16 -7cfde1d [qca-nss-dp] Added nss_dp_hal_hw_reset functionality for ipq53xx.
2023-11-02 -70af6c2 [qca-nss-dp] Implement EDMA hang recovery support
2023-11-27 -2202b29 [qca-nss-dp] Add support for adding the link speed for the Miami's port connected to the internal Switch.
2023-12-06 -bef68a8 [qca-nss-dp] Resolve ring utilization reporting issue in EDMA driver
2023-12-06 -eaa7627 [qca-nss-dp] Add/Delete static fdb entries only for physical ports
2023-10-16 -4551d0f [qca-nss-dp]: Support HLOST_TID_override from PPE_VP path.
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-09-22 -03f83d6 [qca-nss-dp] Correct the mht device flag
2023-08-18 -5efd7f4 [qca-nss-dp] Add EDMA Tx rings for MHT ports
2023-09-11 -7808ba2 [qca-nss-dp] Move DP standby code to new file and use new SSDK API
2023-09-28 -22ade1e [qca-nss-dp] : enable PPE-DS support in 6.x kernel
2023-08-28 -1943922 [qca-nss-dp] Support for bitmap based CPU selection.
2023-08-16 -dcb82a7 qca-nss-dp: 512M profile changes for Miami+Pebble
2023-09-01 -18e51f3 [qca-nss-dp] Fix tx descriptor completion error.
2023-08-28 -0bfde2d [qca-nss-dp] Changes to enable ErP mode
2023-09-05 -f1d635a [qca-nss-dp] Enable fast recycled changes in dp for kernel 6.1
2023-06-15 -55d35bd [qca-nss-dp] Tracking the full utilization of EDMA rings
2023-08-25 -89b9c19 [qca-nss-dp] Restricting the MTU as 9216 for all interfaces in DP
2023-01-03 -5098a4f [qca-nss-dp] Requeue Tx packet in case of Tx-failure.
2023-04-06 -3576dbb [qca-nss-dp] Adding tx napi with four queue per interface.
2023-08-10 -d2b6921 [qca-nss-dp] : changes to support ppe-qdisc for linux 6.x
2023-08-08 -a1941fb [qca-nss-dp] moving SET_NETDEV_DEV for all netdev to set.
2023-07-18 -74d3178 [qca-nss-dp] Reordering the CPU code and ACL index processing.
2023-06-30 -ab03139 [qca-nss-dp] Configure port level PPE offload flag in PPE
2023-06-06 -e9bb8c5 [qca-nss-dp] Rate limit the debug logs.
2023-07-18 -43afb9b [qca-nss-dp] Support Core selection for PPE mirrored packets.
2023-07-11 -92edcfd [qca-nss-dp] Add sysctl to invalidate RX secondary descriptor.
Tested and working on WAX620.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15383
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm recently committed a new branch (12.5.r2) targeting kernel
6.6. This lets us clean up a few patches particularly the one for
"C22/C45" mdio.
A quick way to see what changed for IPQ807x/6018 was to list the files produced
during build (**/*.o), replace the extension with ".c", and doing a
`git log`.
Filtering from those commits, ones of particular interest are listed
below:
```
2024-04-16 - 0d8f30aa - fix compile issue on hk with linux style build
2024-01-29 - 636464f7 - update the check for port link notify
2024-01-24 - 30c10e7f - enable and disable loopback for xgmac to fix qm stuck issue
2024-01-15 - b6ea10aa - update the the APIs to access switch
2024-01-08 - a1687502 - Disable Tx bridge mac before power off the PHY
2024-01-07 - 3eafb613 - support led configure for malibu phy
2024-01-07 - 5c1af60d - remove phy type check from mac reset when mode switch
2023-12-17 - 79d0b1e8 - remove the PHY access APIs in ssdk_plat.c
2023-12-16 - b2953740 - Update mii read/write functions
2023-12-11 - 37f2eac3 - add port id check for fdb entry
2023-12-11 - d040ca4d - support mdio clause45 on kernel6.6
2023-12-07 - 11494fbc - use barrier mw() during access fdb entry table
2023-12-03 - 8e40a284 - fix build warnings on kernel6.6
2023-11-10 - 10aa0a02 - change speed value when call ssdk_port_link_notify
2023-11-06 - ee4c4a60 - Update mac bitmap value of L3 table on MAC delete
2023-11-03 - 7cd27d39 - support 10G phy common feature
2023-10-30 - 383cc0d2 - fix mactype and mux select issue
2023-10-24 - decf534a - support autoneg status query on force port
2023-10-11 - 111d574e - move ssdk_led_init to regi_init
2023-10-08 - 6b14c142 - the combo port also need to parse SFP pins
2023-10-03 - fb2e0401 - fix port5 interface mode switch issue in erp case
```
Verified with users on QNAP 301W, NBG7815, and myself on Dynalink
DL-WRX36 that everything is functional, including LEDS.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15379
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Allow kmod-acpi-video to be built for loongarch64:
The x86-specific CONFIG_ACPI_WMI will be split from default
kmod-acpi-video as a board-specific addition.
* Allow kmod-drm-amdgpu to be built for loongarch64:
Also add loongarch64-specific configs and modules.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
netlink.h header have NL_SET_ERR_MSG_MOD that is tied to kmods. We don't
need kmods on bpf tools and this cause compilation error if the header
is included. Fix it by dropping NL_SET_ERR_MSG_MOD.
Link: https://github.com/openwrt/openwrt/pull/11825
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds a kernel module package for the Marvell
MV88E6XXX DSA switch and a separate module package for
the DSA tagger since it can in theory be used by multiple
DSA switches. Enable both DSA and EDSA tags in the
tagger.
We can't just compile this in because just a few devices
has this DSA, and it depends on e.g. the I2C and SFP
to be loaded as modules first.
We have no examples of DSA switches being packaged as
modules before, all seem to be compiled in, but it
actually works just fine to do this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This update contains a minor fix to resolve "detected write beyond size
of field" warning during compilation:
* "replace [0] with []" (1d0d08c)
All patches still apply.
References:
* https://github.com/openwrt/openwrt/issues/15108
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
It seems that move to kernel 6.6 somehow fixed the remoteproc restart so
now it properly restarts and thus coldboot calibration works as well.
ipq60xx still seems to be broken in a different way so keep it disabled.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch fixing rmmod and insmod. Lots of flawed logic fixed that
permits the module to correctly rmmod and insmod later.
Just to quote some change, use phy_detach instead of phy_disconnect, fix
exclusive reset_control that could only be used once, fix kernel panic
on second edma_cleanup, stop traffic before module exit...
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Limiting allowed channels per device may be required and is commonly
supported on other drivers, so include a pending patch to add support for
the same.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Starting with Linux 6.3 the .probe call no longer got the id parameter,
see also commit torvalds/linux@03c835f498
("i2c: Switch .probe() to not take an id parameter").
As the parameter is anyway unused by the driver, drop it when
building the GCA230718 LED driver for newer kernels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This module supports the Microchip Technology Inc (SMSC)
EMC2301/EMC2302/EMC2303/EMC2305 fan speed PWM controller chips.
Signed-off-by: Oleg S <remittor@gmail.com>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
This commit removes all code that support implicit handling of
subtargets and instead requires every target to define "SUBTARGETS".
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using zst instead of xz, the hash changes. This commit fixes the
hash for packages and tools in core.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fix compilation warning enum-int-mismatch which results in failure to
build kmod-ltq-vmmc in case CONFIG_KERNEL_WERROR is set.
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:392:14: error: conflicting types for 'ifx_mps_fastbuf_init' due to enum/integer mismatch; have 'IFX_return_t(void)' [-Werror=enum-int-mismatch]
392 | IFX_return_t ifx_mps_fastbuf_init (IFX_void_t)
| ^~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:120:13: note: previous declaration of 'ifx_mps_fastbuf_init' with type 'IFX_int32_t(void)' {aka 'int(void)'}
120 | IFX_int32_t ifx_mps_fastbuf_init (IFX_void_t);
| ^~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:420:14: error: conflicting types for 'ifx_mps_fastbuf_close' due to enum/integer mismatch; have 'IFX_return_t(void)' [-Werror=enum-int-mismatch]
420 | IFX_return_t ifx_mps_fastbuf_close (IFX_void_t)
| ^~~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:121:13: note: previous declaration of 'ifx_mps_fastbuf_close' with type 'IFX_int32_t(void)' {aka 'int(void)'}
121 | IFX_int32_t ifx_mps_fastbuf_close (IFX_void_t);
| ^~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Refresh patches and bump PKG_RELEASE while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include the CONFIG_KVM_SMM option in the kvm-x86 package to enable system management mode emulation on KVM.
Co-authored-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fix error: Package kmod-lan743x is missing dependencies for the following libraries:
fixed_phy.ko
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Kernel 6.2 folded virqfd (eventd interface for VFIO interrupts)
into the base vfio module, it is no longer a tristate option.
Change suggested by vincejv on GitHub:
https://github.com/openwrt/openwrt/pull/14868#issuecomment-1998260124
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Instead of redefining the version schema in cryptodev, use the one
automatically defined via `kernel.mk`.
Specifically this changes the version from <kernel>+<package> to
<kernel>.<package> and thereby making it compatible with APK.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add patch fixing compilation with kernel 6.6.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation with kernel 6.6.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add debugfs entry for disabling frames buffering that may be a reason
for mt7603 instability. This patch was sent upstream for review and at
least wasn't rejected yet. Let's add it to let OpenWrt users test if it
really helps.
Example usage:
echo N > /sys/kernel/debug/ieee80211/phy0/mt76/frames_buffering
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Build files shouldn't be symlinked into the staging directory, as doing so
would create a race condition if the build folder for 'qca-nss-dp' gets
deleted for any reason.
We should instead just copy over the required platform file to avoid
breaking compilation for any dependent packages.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
The current build procedure always wipes away build files, this is
costly as ssdk is a parent dependency on a whole host of packages and
will always end up rebuilding (and in serial) the whole package.
This patch includes:
1. Module Building Optimization: Instead of creating a temporary
directory (temp) and copying files into it for module building,
the directly invoke the module build command with the
necessary paths. This simplifies the build process
and avoids unnecessary file operations, speeding up
the build process and reducing disk usage.
2. Parallel Build Support: By removing the explicit creation of
the temporary directory and associated file copying operations,
and passing in $(MAKE) $(PKG_JOBS) allows building in parallel.
3. Fix `EXTRA_CFLAGS`: This variable is referenced and set within MAKE_FLAGS,
so doesn't preserve spaces. Should have its defined value quoted.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Add basic support for the LED driver for GCA230718.
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Kernel 6.3 has introduced separate C45 read/write operations, and thus
split them out of the C22 operations completely so the old way of marking
C45 reads and writes via the register value does not work anymore.
This is causing SSDK to fail and find C45 only PHY-s such as Aquantia ones:
[ 22.187877] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 8, phy_id = 0x0 phytype doesn't match
[ 22.209924] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0x0 phytype doesn't match
This in turn causes USXGMII MAC autoneg bit to not get set and then UNIPHY
autoneg will time out, causing the 10G ports not to work:
[ 37.292784] uniphy autoneg time out!
So, lets detect C45 reads and writes by the magic BIT(30) in the register
argument and if so call separate C45 mdiobus read/write functions.
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the change in version schema the downloaded files changed, too,
mostly the hash is now prefixed with a tilde `~` instead of a dash `-`.
Since each downloaded archive contains folder with the same name as the
archive, the checksum changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add imx8m support:
- add a cortexa53 subtarget to imx
- move ARCH and KERNELNAME to subtargets
- account for kernel modules that are not used for cortexa53
No device-specific targets or firmware images are created yet but all
imx8m* dtbs will be built.
enabling CONFIG_TARGET_ROOTFS_INITRAMFS results in
openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin which has been
successfully booted on an imx8mm-evk using the following:
u-boot=> tftpboot $fdt_addr_r image-imx8mm-evk.dtb && \
tftpboot $kernel_addr_r openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin && \
booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The carl9170_tx_release() function sometimes triggers a fortified-memset
warning in my randconfig builds:
In file included from include/linux/string.h:254,
from drivers/net/wireless/ath/carl9170/tx.c:40:
In function 'fortify_memset_chk',
inlined from 'carl9170_tx_release' at drivers/net/wireless/ath/carl9170/tx.c:283:2,
inlined from 'kref_put' at include/linux/kref.h:65:3,
inlined from 'carl9170_tx_put_skb' at drivers/net/wireless/ath/carl9170/tx.c:342:9:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
Kees previously tried to avoid this by using memset_after(), but it seems
this does not fully address the problem. I noticed that the memset_after()
here is done on a different part of the union (status) than the original
cast was from (rate_driver_data), which may confuse the compiler.
Unfortunately, the memset_after() trick does not work on driver_rates[]
because that is part of an anonymous struct, and I could not get
struct_group() to do this either. Using two separate memset() calls
on the two members does address the warning though.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
enable support for RK35xx in kmod-ata-ahci-platform kernel module
Suggested-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Different from OPKG, APK uses a deterministic version schema which chips
the version into chunks and compares them individually. This enforces a
certain schema which was previously entirely flexible.
- Releases are added at the very and end prefixed with an `r` like
`1.2.3-r3`.
- Hashes are prefixed with a `~` like `1.2.3~abc123`.
- Dates become semantic versions, like `2024.04.01`
- Extra tags are possible like `_git`, `_alpha` and more.
For full details see the APK test list:
https://gitlab.alpinelinux.org/alpine/apk-tools/-/blob/master/test/version.data
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since 6.5 netdev_rx_queue was moved out of netdevice.h so include the new
header since that is where it lives now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update the deprecated license information from GPL-2.0 to GPL-2.0-only
as written in the COPYING file of the linux source tree.
Also add the 'COPYING' file to the PKG_LICENSE_FILES variable.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The lincense information for the packages mac80211 are missing.
This commit adds the missing information.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
a903d3169193 wifi: mt76: mt7921: fix a potential association failure upon resuming
eb0d0ce344f3 wifi: mt76: mt7921: fix suspend issue on MediaTek COB platform
841bf82e9958 wifi: mt76: fix the issue of missing txpwr settings from ch153 to ch177
ce7ccc540168 wifi: mt76: Remove redundant assignment to variable tidno
a238df940d6f wifi: mt76: mt7915: initialize rssi on adding stations
46c7d1849dbd wifi: mt76: replace skb_put with skb_put_zero
b5640b3153c7 wifi: mt76: fix tx packet loss when scanning on DBDC
7b054e5cb3af wifi: mt76: mt7915: fix mcu command format for mt7915 tx stats
3f27a64a8010 wifi: mt76: mt7915: fix bogus Tx/Rx airtime duration values
4f681a8fbc91 wifi: mt76: mt7915: fix HE PHY capabilities IE for station mode
8ede229eb8b5 wifi: mt76: mt7915: only set MT76_MCU_RESET for the main phy
2330781b8c5f wifi: mt76: mt7996: only set MT76_MCU_RESET for the main phy
e5fb6995e7eb wifi: mt76: mt7915: add support for disabling in-band discovery
b4a917417c85 wifi: mt76: mt7915: add mt7986, mt7916 and mt7981 pre-calibration
2135e201e7a9 mt76: mt7915: add fallback in case of missing precal data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Build and package driver for MediaTek PCIe 5G WWAN modem T7xx device
available in Linux 6.1 and 6.6 as kmod-mtk-t7xx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add a separate bit in struct ieee80211_tx_info to indicate airtime tracked
as broadcast/multicast. This avoids a race condition where airtime from
stations that were just removed wasn't getting subtracted from the total
PHY airtime.
Fixes: 95e633efbd ("mac80211: add AQL support for broadcast/multicast packets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
drm-amdgpu and drm-radeon require drm-exec and/or drm-suballoc-helper in
6.6, so since we have them packaged separately include them when required.
Fixes: 5b08b56007 ("kernel: modules: video: adapt for kernel 6.6")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux 6.4 has split out the previously AMDGPU specific suballocation
helper into a generic one and it has its own symbol now.
So, lets package it as a separate helper as AMDGPU still requires it
for 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
As part of adding kernel 6.6 support, DRM_EXEC and DRM_SUBALLOC_HELPER were
added to the kmod-drm, however these are only used by drm-amdgpu and
drm-radeon which are only supported on x86.
So, lets start fixing building of other targets by removing these from the
main kmod-drm, in follow-up commits they will be packaged separately and
selected when required.
Fixes: 5b08b56007 ("kernel: modules: video: adapt for kernel 6.6")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Many can kernel modules are now gated by the newly introduced
CONFIG_CAN_NETLINK configuration option. Activate it to build the can
drivers again.
This was changed in this upstream Linux commit:
https://git.kernel.org/linus/df6ad5dd838e0fa543ca28ca6154901fa65a9443
This should fix these warnings with kernel 6.1 and 6.6:
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-pci is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-c-can-platform is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-mcp251x is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-slcan is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-8dev is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-ems is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-kvaser is not available in the kernel config - generating empty package
logs/package/kernel/linux/compile.txt:WARNING: kmod-can-usb-peak is not available in the kernel config - generating empty package
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The algif_rng.ko kernel module depends on the rng.ko kernel module with
kernel 6.6 when compiling for MIPS malta.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Recent changes for Linux 6.6 broke things when building with older
kernels:
Package kmod-fs-jfs is missing dependencies for the following libraries:
nls_base.ko
Fix this by adding NLS dependencies after the added dependency applying
on Linux 6.6.
Fixes: f9198480da ("kernel: modules: fs: adapt for kernel 6.6")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
A commit introduced in kernel 6.6 has splitted page_pool.h into
several headers. Thus the included header must be modified for a
successful build.
Ref: a9ca9f9ceff3 (page_pool: split types and declarations from
page_pool.h)
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Now that geniv is packaged separately for kernel 6.6, we need to add it
as a dependency to kmod-crypto-seqiv and kmod-crypto-echainiv that require
it under kernel 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
geniv was separated intentionally from aead in kernel 6.5, and since
we now have it packaged separately as well remove it from kmod-aead
in 6.6.
Signed-off-by: Robert Marko <robimarko@gmail.com>
In kernel 6.5 geniv was split from AEAD config symbol, in order to manage
its dependencies on other code.
So, lets do the same in OpenWrt and split it from aead module so others
can depend on geniv directly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adapt hwmon kmods for building under kernel 6.6:
* ad7418 now requires regmap
* Invert criteria to allow adt7410 be built with Linux 6.1 as well
as Linux 6.6.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Adapt crypto kmods for building under kernel 6.6:
* mpi.ko moved from lib/mpi/mpi.ko to lib/crypto/mpi/mpi.ko
* jitterentropy_rng requires SHA3 support for kernel 6.6
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt video kmods for building under kernel 6.6:
* Add drm_exec.ko and drm_suballoc_helper.ko for kmod-drm as they
are added since 6.6 and 6.4
* Add uvc.ko for kmod-video-uvc as related contents was split as a
new module since 6.3
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt block kmods for building under kernel 6.6:
* To build scsi_transport_iscsi.ko, change CONFIG_SCSI_ISCSI_ATTRS
from =y to =m as this config is always tristate since 2.6.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt fs kmods for building under kernel 6.6:
* Add kmod-fs-netfs as dependency for kmod-fs-9p
* Add kmod-fs-netfs as dependency for fs-smbfs-common as netfs is
required for cifs since 6.3
* Add new kmod-nls-ucs2-utils as dependency for smbfs/jfs as UCS2
support was split as new module since 6.6.
* Add kmod-lib-zlib-deflate and kmod-lib-zlib-inflate as
dependencies for kmod-pstore due to crypto API compression was
replaced with zlib_deflate library calls since 6.6
* Remove nfs_ssc.ko from kmod-fs-nfs-common. The nfs_ssc was no
longer a kernel module described by NFS_V4_2_SSC_HELPER since 5.13 [1]
Link:
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/fs/Kconfig?id=d9092b4bb2109502eb8972021a3f74febc931a63
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt usb kmods for building under kernel 6.6:
* Add kmod-phylink as dependency for usb-net-asix
* Add kmod-net-selftests as dependency for usb-net-smsc95xx
* Add kmod-iio-core as dependency for usb-hid-mcp2221 as ADC/DAC
support was added since 6.2 which requires IIO.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt netdevices kmods for building under kernel 6.6:
* Add missing module dependency for kmod-stmmac-core on kmod-of-mdio.
* Invert criteria to allow Airoha EN8811H PHY driver to build with
Linux 6.1 as well as Linux 6.6.
* Mellanox mlx5 driver started exposing thermal sensors and now it requires
hwmon
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adapt netsupport kmods for building under kernel 6.6:
* common part of mqprio was split into a new Kconfig since 6.3.
Add new kmod-sched-mqprio-common as dependency for kmod-sched-mqprio.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt input kmods for building under kernel 6.6:
* kmod-input-touchscreen-edt-ft5x06 depends on kmod-regmap-i2c
from 6.3 as it starts to use regmap to access registers
* CONFIG_HID_SUPPORT needs to be set in addition to CONFIG_HID.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Adapt iio kmods for building under kernel 6.6:
* kmod-iio-lsm6dsx depends on kmod-kmod-industrialio-triggered-buffer
from 6.2
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
As the Visionfive V1 board has an Ampak module connected via SDIO, enable
support for SDIO in the brcmfmac module.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
CDNS3 is a SuperSpeed (SS) USB 3.0 Dual-Role-Device (DRD) controller from
Cadence. Add support for this device, and add the required symbols into
the generic configs.
Compile-tested: apm821xx, bcm4908, imx, mpc85xx, pistachio, starfive
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The AQL limit for buffered broadcast packets is higher than the maximum
total pending airtime limit. This can get unicast data stuck whenever there
is too much pending broadcast data. Fix this by excluding broadcast AQL from
the total limit.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
At start I only set qualcommax to use the Crypto Extensions optimized
version of SHA256 as I knew it supports the optional Crypto Extensions.
However, after looking into the tree there are more targets/subtargets
that I could find at least a specification sheet that says the support
Cryptographic Extensions, so lets add them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
At start I only set qualcommax to use the Crypto Extensions optimized
version of SHA1 as I knew it supports the optional Crypto Extensions.
However, after looking into the tree there are more targets/subtargets
that I could find at least a specification sheet that says the support
Cryptographic Extensions, so lets add them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
ath25 has been on life support for the last couple of releases, eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release which was a challenge due to small RAM amount.
However, with the attempt of kernel 6.1 update it turns out that kernel
cannot even finish booting due to RAM constraints, so its time to let this
target go.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel has an ASM optimized version of SHA512 that was ported from
OpenSSL, so lets package it as it provides significant perfomance
improvement compared to the generic implementation.
There is a Cryptographic Extension based version as well, but that relies
on ARMv8.2 ISA which I am not aware any of the OpenWrt supported SoC-s use.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel has optimized version of SHA2(224 and 256) using the ARMv8 Crypto
Extensions, so lets package it.
Use it by default for qualcommax as it uses Cortex-A53 core and has ARMv8
CE extensions present.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel has an ASM optimized version of SHA256 that was ported from
OpenSSL, so lets package it as it provides significant perfomance
improvement compared to the generic implementation.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel has optimized version of SHA1 using the ARMv8 Crypto Extensions,
so lets package it.
Use it by default for qualcommax as it uses Cortex-A53 core and has ARMv8
CE extensions present.
Signed-off-by: Robert Marko <robimarko@gmail.com>
SHA3 is now required by jitterentropy_rng in kernel 6.6, so lets start
preparing by packaging SHA3 support as its supported in 5.15 and 6.1
kernels as well.
AFAIK, only ARMv8.2 has a crypto extension for SHA3, however I am not aware
of any SoC we support that uses ARMv8.2 ISA so its not enabled currently.
Signed-off-by: Robert Marko <robimarko@gmail.com>
asterisk-chan-lantiq is by now the only user of the VMMC interface.
And asterisk runs as user 'asterisk' which doesn't give it permission
to open the /dev/vmmc* devices.
Introduce a new user group 'vmmc' and give permission to access the
/dev/vmmc* devices to that group.
Another commit for asterisk-chan-lantiq will add the 'asterisk' user
to that group.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Kirkwood SoCs all have an onchip RTC that can hold the time
over e.g. a reboot which will help if no NTP servers are available.
Create a kernel module package for the Marvell RTC, and add it to
all Kirkwood devices that do not have their own discrete
battery-backed RTC. Adding it to platforms with a proper RTC
is just surplus.
All Kirkwoods have at least one RTC so add RTC to the features
list for Kirkwood as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When both variants of ath10k drivers are selected, any driver that is
selected along is being built twice, one for each ath10k variant.
Avoid these redundant builds by introducing an optional second parameter
to config_package that lists the variants for which the package is to be
built.
If the symbol is to be set for all of the variants, $(ALL_VARIANTS) can
be used. This is the case for the mac80211 and cfg80211 modules. If
the parameter is empty, then the module will be selected and thus built
when the first variant is compiled.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Having different build directories is the default when the package
Makefile defines more than one variant.
Mac80211 overrides PKG_BUILD_DIR, not taking different variants in
consideration, which causes clobbering the directories when both
variants are built.
When compiled with AUTOREMOVE=y, the effect is that the package is
unnecessarily rebuilt when the package is compiled again.
Wihout AUTOREMOVE, the problem is worse: the second variant will not be
rebuilt, and you end up with the smallbuffers variant being a copy of
the regular one.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
When QCA8072 is used in PSGMII mode with IPQ6018, PCS used for second
PHY port would overlap with one used by SGMII+ port. SoC has register
to select different PCS in such case.
Original code used PHY_ID for this decision, which also had other
issues, but is no longer viable since we moved to upstream QCA807x
driver.
Introduce DT property port3_pcs_channel to allow describing this in DT.
Default value is <2>, and for some QCA8072 designs <4> would be needed.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Add PHY driver for Airoha EN8811H PHY and package it as kernel module.
The PHY needs to load firmware from rootfs, so there is no point in
having the driver built-into the kernel.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that Malibu (QCA807x) PHY-s use an upstream driver we dont need support
for defining address of the first PHY in the package so drop the patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop deprecated Xiaomi LEDs quirk patches as they are not needed anymore
as LEDs are now supported by the upstream qca807x driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
If a PHY doesn't use the integrated driver, SSDK use poll the phydev to
get the real PHY mode. qca807x use PSGMII as PHY mode and this specific
mode is not detected in qca SSDK while used in the entire driver.
Add support for it in the hsl_port_phydev_interface_mode_status_get
function used to translate PHY mode to the internal SSDK value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Disable Malibu PHY driver in Qca SSDK in favor of the upstream version.
The same workaround are applied and the version upstream is just a drop
in replacement and is well tested from the ipq40xx target.
Also using the upstream version permits further support for LEDs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
IPQ60xx uses a different codename for SSDK, so lets pass the correct one
as otherwise SSDK asumes we are building for the old MIPS SoC-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
[ drop outdated commit description info ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
v4l2-common.ko was merged into videodev.ko and no longer exists.
Fixes: ac5671f46c ("kernel: remove obsolete kernel version switches for 4.19")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The coda kernel modules were moved between 5.15 and 6.1.
Adapt the coda-vpu and imx-vdoa modules for that.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Linux 6.1 changed DRM_GEM_DMA_HELPER to a module (drm_dma_helper.ko).
Add this to the drm-imx to fix module dependencies.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Linux 6.1 wraps core video drivers in a MEDIA_PLATFORM_DRIVERS submenu.
Enable that for 6.1 and add some new necessary undefines to
target/linux/generic/config-6.1 to avoid build failures.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
kmod-drm-imx-hdmi depends on kmod-drm-display-helper since 6.1. Include
that in OpenWrt's recipes.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
This adds support for the Fritzbox 7490 device. It contains two
SoCs, one Lantiq without WiFi and one QCA9558 with 2.4GHz
and 5 GHz WiFi. Only the Lantiq has access to the flash memory,
the Atheros runs fully from RAM and is booted by using a remoteproc
kernel module and is not supported with this commit.
The devices were manufactured with varying NAND chips which
requires Micron and non-Micron versions of the images.
Specifications:
- SoC: Lantiq 500 MHz
- RAM: 256 MB
- Storage: 512 MB NAND, 1MB FLASH
- Wireless, separate SOC QCA9558 with 128MB RAM (not supported yet):
· Qualcomm-QCA9558 w/ 3×3 MIMO for 2.4GHz 802.11b/g/n
· Qualcomm-QCA9880 w/ 3×3 MIMO for 5GHz 802.11a/ac
· AG71xx ethernet
- Ethernet: Built-in AR 803x, 7 port 4 phy switch,
4x 1000/100/10 port, Port 5 is fixed and connected to the WASP SOC
- Renesas µPD720202 USB3 PCIe, requires firmware binary on the device
- VDSL2 modem
Unsupported:
- DECT and ISDN telephony
Installation:
Check which NAND the device has by using the following procedure with
stock firmware:
Go to to http://<fritzbox_ip>/support.lua, download the support data
file and search for string "NAND device" to get the manufacturer kernel
output.
Use Micron image if Micron is displayed otherwise the non-Micron image.
Use the eva_ramboot.py script to boot the initramfs image. Follow the
procedure to interrupt booting by ftp into 192.168.178.1 within
5 seconds after poweron.
Then transfer the sysupgrade image to the device and run sysupgrade to
flash it to the NAND.
For making USB work, an renesas xhci firmware file (e.g. v2026) is
needed and it should be copied to /lib/firmware/ (file name
renesas_usb_fw.mem).
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Since we have the 'GPIO support' menu, it is strange to look up
gpio related modules in 'Other modules' menu. So move these
modules and put them in the gpio menu.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Disable compiling qca8081 PHY driver in favor of upstream to better
support it and add better control of attached LEDs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Completely disable dump_survey code on ARCH_BCM2835 to fix defined but not
used warning.
512b762ddb (commitcomment-137899352)
Fixes: 512b762ddb ("mac80211: brcm: disable dump_survey on Raspberry Pi")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Enabling this causes slow iwinfo calls on Raspberry Pi and LuCI slows down
when wireless is enabled.
Fixes: https://github.com/openwrt/openwrt/issues/14013
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch has been reverted in the Raspberry Pi linux repository.
Also refresh the rest of the patches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
[rmilecki: port to 5.15]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
raspberrypi/firmware is about 40G, so getting the full history log isn't an
option.
There have been multiple improvements and also support for the RPi 5 has been
added.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel module for lp5562 LED driver.
The kmod-leds-lp5562 depends on kmod-leds-lp55xx-common.
Signed-off-by: CheWei Chien <chewei.chien@wnc.com.tw>
This reverts commit b7f9742da8.
There are several reports of regressions with this commit. Will be added
back once I've figured out and fixed the cause
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When hitting a timing window where ubus configuration calls are hitting hostapd
and wpa_supplicant simultaneously, they can deadlock waiting for each other.
Fix this by using a lock around the ubus calls.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Frequent crashes have been observed on MT7916 based platforms. While the
root of these crashes are currently unknown, they happen when decoding
rate information of connected STAs in AP mode. The rate-information is
associated with a band which is not available on the PHY.
Check for this condition in order to avoid crashing the whole system.
This patch should be removed once the roout cause has been found and
fixed.
Link: https://github.com/freifunk-gluon/gluon/issues/2980
Signed-off-by: David Bauer <mail@david-bauer.net>
Add modules.builtin.modinfo to the kernel package, to support presence
testing using module aliases and printing module details with 'modinfo'.
With related kmodloader changes this adds ~2 KB to compressed image sizes.
root@OpenWrt:/# modinfo unix
name: unix
filename: (builtin)
alias: net-pf-1
license: GPL
root@OpenWrt:/# modprobe net-pf-1 && echo SUCCESS || echo FAIL
SUCCESS
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add modules.builtin to the kernel package for improved handling of loadable
and builtin modules. As with other distros, this allows 'modprobe <module>'
to consistently return success for both loaded/built-in modules, a useful
feature for presence-testing.
Given OpenWrt's few built-in modules, this change and related kmodloader
support add ~1 KB to the compressed image size.
Using sch_fq_codel (builtin) and sch_cake (loadable) for example:
root@OpenWrt:/# modprobe sch_fq_codel && echo SUCCESS || echo FAIL
SUCCESS
root@OpenWrt:/# modprobe sch_cake && echo SUCCESS || echo FAIL
SUCCESS
root@OpenWrt:/# rmmod sch_fq_codel
module is builtin
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes WARN_ONs when using AP_VLANs after station removal. The flush
call passed AP_VLAN vif to driver, but because these vifs are virtual and
not registered with drivers, we need to translate to the correct AP vif
first.
Fixes: openwrt#12420
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Detach of-mdio dependency from stmmac-core kmod to fix support for
x86_64 target. This target doesn't use OpenFirmware infrastructure and
stmmac-core for the dwmac-intel driver doesn't depends on it.
Add kmod-of-mdio to any other user of stmmac-core as it's not inherit
from stmmac-core anymore.
Fixes: #14209
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move pcs-xpcs kmod from armsr modules.mk to generic modules package.
Also add additional dependency to x86_64 as stmmac-core it's now used
by x86_64 target and depends on this package.
Fixes: 4b4c940fbc ("x86: Add kmod-dwmac-intel")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Might be a typo in drv->txtstamp function:
+ phy_rxtstamp(ndev->phydev, skb, 0);
to
+ phy_txtstamp(ndev->phydev, skb, 0);
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Remove upstreamed patches:
* replace usage of the deprecated "pci-dma-compat.h" API (6c03b27)
* remove uaccess and get_fs calls from PCIe for Kenel >= 5.18 (1d0d08c)
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ISISC is the QCA codename for their Atheros switch family including
AR237, QCA8337 etc.
Since we have qca8k support in OpenWrt, there is no need to have SSDK
support for these switches, and boards that also have external switches
can just use qca8k.
Disable QCA803x PHY support as well, since all of those are supportable
via at803x driver.
Signed-off-by: Robert Marko <robimarko@gmail.com>
PTP and swconfig support in SSDK require kernel modifications we dont need
nor we want to support for now, so move the PTP and swconfig disablement
into general build options as they are not ipq807x specific.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Recent SSDK versions started also parsing the "SoC" variable to identify
the SoC along with the "CHIP_TYPE".
We are not passing "SoC" currently and this leads to components we dont
need like MHT (New 2.5G quad port switch) being compiled and then unused,
so lets just pass the "SoC" as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTW88 PCI/USB driver uses the same firmware,
so add firmware dependencies.
Also CI report that:
Package kmod-rtw88-usb is missing dependencies for the following libraries:
usbcore.ko
This commit fixes it.
Fixes: 3538a19 ("mac80211: split rtw88 configuration for each supported chip")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Commit 947b44d ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this. Also update each DTS with the new required
property if needed.
The new binding malibu_phy_start_addr is required with devices that
place the malibu first PHY referring port1 on a different PHY addres
than 0. The most common configuration is 0 but some device (for example
Qnap 301W) place the malibu PHY at an offset to address 16.
Refer to ipq8074-ess dtsi for extensive description on how to derive
this value.
Quoting the patch detailed description:
The usage of first_phy_addr is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this prefaction in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, introduce a new binding malibu_first_phy_addr to manually
declare the first phy that the malibu PHY driver should use and permit
to detach it from port bmp detection. The legacy detection is kept for
compatibility reason.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com> # Qnap 301W
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 8cce00bc9d.
The confusion was real and this change cause regression on other
advanced devices that makes actual use of the first_phy_addr value.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some local patches have been sent to upstream and they are slightly
different from the upstream version. So it's better to replace them
to avoid conflicts with the new mac80211 backport driver. The
different parts have been merged into patch 996.
This commit also includes some additional fixes:
* Fix watchdog function.
* Improve MT7620 register initialization.
* Introduce DMA busy watchdog for rt2800.
P.S.
Sometimes rt2800 series chips may fall into a DMA busy state. The
tx queues become very slow and the client cannot connect to the AP.
Usually, We can see a lot of hostapd warnings at this point:
'hostapd: IEEE 802.11: did not acknowledge authentication response'
The DMA busy watchdog can help the driver automatically recover
from this abnormal state. By the way, setting higer 'cell_density'
and disabling 'disassoc_low_ack' can significantly reduce the
probability of the DMA busy.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Kernel 6.1 has introduced support for RTW8822BU network adapter, which
is an USB variant of the rtw8822b 802.11ac chipset family.
Build and install the corresponding module in the rtw88 package
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Current rtw88 build configuration builds modules for all chips supported by
rtw88 driver family. This brings the following issues:
- adding a chip with a different bus is not convenient (all chips currently
depends on PCI)
- some features requirements are not relevant for all chips in family (eg
802.11AC is enforced but RTW88-8723DE is only a 802.11b/g/n chip)
Remove those constraints/issues by adding one module build option per
supported chip, and add intermediate options to properly cascade
dependencies.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
ath9k-htc USB-based adapters also support 5/10MHz channel bandwidth.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ath9k-htc USB-based adapterssupport 5/10MHz channel bandwidth, the
same as standard ath9k ones.
Move the code handling the features in debugfs to common-debug.c,
and create proper registration functions to use in debug.c and
htc_drv_debug.c, leaving only debugfs registration there.
While at that, refresh one patch that would conflict otherwise.
Tested on TP-Link Archer C7v2 (ath79) and TP-Link WN722Nv1 (AR9287)
and WN822Nv2 (AR7010+AR9287).
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
In-kernel driver for MCS7715 USB-serial bridge has a bool option,
enabling support for parallel port on that chip - which is tied to the
same kernel module. Enable it and select kmod-ppdev, as the image size
increase is minimal and the package isn't bundled in the images by
default.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Adjust our local ath10k-ct patches to the change
from the -ct 6.2 version to 6.4.
This restores e.g. the LED functionality.
Fixes: 7d3651f1b9 ("ath10k-ct: switch to 6.4")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Commit 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
started fixing wrong switch_lan_bmp that defined lan there weren't
actually present. This displayed a fragility in the malibu phy init code
in qca-ssdk.
Add patch to fix this.
Quoting the patch detailed description:
I'm very confused by this and to me it's not clear the real usage of
this logic.
From what I can see the usage of this is EXTREMELY FRAGILE and results
in dangerous results if the OEM (or anyone that by chance try to
implement things in a logical manner) deviates from the default values
from the "magical template".
To be in more details. With QSDK 12.4, some tweaks were done to improve
autoneg and now on every call of port status, the phydev is tried to
add. This resulted in the call and log spam of an error with ports that
are actually not present on the system with qsdk reporting phydev is
NULL. This itself is not an error and printing the error is correct.
What is actually an error from ages is setting generic bitmap reporting
presence of port that are actually not present. This is very common on
OEM where the switch_lan_bmp is always a variant of 0x1e (that on bitmap
results in PORT1 PORT2 PORT3 PORT4 present) or 0x3e (PORT1 PORT2 PORT3
PORT4 PORT5). Reality is that many device are used as AP with one LAN
port or one WAN port. (or even exotic configuration with PORT1 not
present and PORT2 PORT3 PORT4 present (Xiaomi 3600)
With this finding one can say... ok nice, then lets update the DT and
set the correct bitmap...
Again world is a bad place and reality is that this cause wonderful
regression in some case of by extreme luck the first ever connected
port working and the rest of the switch dead.
The problem has been bisected to all the device that doesn't have the
PORT1 declared in any of the bitmap.
With this perfection in mind, on to the REAL problem.
malibu_phy_hw_init FOR SOME REASON, set a global variable first_phy_addr
to the first detected PHY addr that coincidentally is always PORT1.
PORT1 addr is 0x0. The entire code in malibu_phy use this variable to
derive the phy addrs in some function.
Declaring a bitmap where the PORT1 is missing (or worse PORT4 the only
one connected) result in first_phy_addr set to 1 or whatever phy addr is
detected first setting wrong value all over the init stage.
To fix this, just drop this variable and hardcode everything to assume
the first phy adrr is ALWAYS 0 and remove calculation and use define for
special case.
With the following change normal switch traffic is restored and ports
function is recovered.
Fixes: #13945
Fixes: 947b44d9ae ("ipq807x: fix wrong define for LAN and WAN ess mask")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option was changed to hostapd_noscan but the entry in
wpa_supplicant was never updated resulting in the noscan option actually
never set.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update SSDK version to 12.4, this fixes weird SFP port link up/downs
while there is no SFP module plugged in.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes the download of the kernel 5.15 for the bpf-headers when
kernel 6.1 is build for the target.
Even if kernel 6.1 was selected for the target we still use kernel 5.15
for the bpf-headers. The download script tried to download the 5.15
kernel from the 6.x directory on kernel,org and this failed. Define
PKG_SOURCE_URL based on PKG_PATCHVER and not KERNEL_BASE like done in
kernel.mk.
Without this change it tries to download the kernel from this URL:
ttps://cdn.kernel.org/pub/linux/kernel/v6.x/linux-5.15.129.tar.xz
Fixes: #13190Fixes: #13671Fixes: #13814
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ath10k-ct based on kernel 6.4 doesn't have a fix present in previous
kernel. Add patch that port the compilation error fix from previous
kernel in the new 6.4 kernel.
Fixes: 7d3651f1b9 ("ath10k-ct: switch to 6.4")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch to the latest version so we match as close as possible to
our own mac80211 version.
Run-time tested on hundreds of devices in the field for months now:
- qca988x (wave 1)
- qca4019 (wave 2)
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Add a struct_group to around all members in struct ath_cycle_counters.
It can help the compiler detect the intended bounds of the memcpy() and
memset().
This patch fixes the following build warning:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at /home/db/openwrt/build_dir/target-mips_24kc_musl/linux-ath79_generic/backports-6.1.24/drivers/net/wireless/ath/ath9k/main.c:140:3:
./include/linux/fortify-string.h:314:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
314 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Currently the zram default compressor choice is displayed whether or not
zram is activated. Since the default choice is lzo-rle, this adds a
false dependency on kmod-lib-lzo.
With this patch, the choice options appear only when activating zram.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Fix the building issue setting CC to KERNEL_CC in kernel.mk. The
kernel backports by default uses CC to compile kconf. A new patch is
added to mac80211 to compile kconf with host gcc.
Signed-off-by: Zeyu Dong <dzy201415@gmail.com>
[ refresh patches ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_USB_AUDIO is a "USB Audio Gadget" driver, not a usb device driver
CONFIG_USB_AUDIO is "USB Audio support" before linux 2.6
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Expose the temperature sensors as hwmon, it improves the overall
user experience since on tiny boards the nvme can become a substantial
source of heat.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The IXP4xx crypto module must be loaded after the rootfs is
up as it depends on loading some NPE microcode from the file
system.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of new toolchain define. TOOLCHAIN_DIR should be used only for
toolchain related packages and for everything else TOOLCHAIN_ROOT_DIR
and other define should be used instead.
Switch to new entry where possible.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some packages won't ever have something to patch as they normally
install files or are meta-packages.
For these special packages, disable QUILT refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
To support the IXP42x platforms we need a kernel module
for the Epson R7301 RTC so we can load it as an optional
module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
To support the IXP42x platforms we need a kernel module
for the X1205 RTC so we can load it as an optional module.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
The lib-chacha20 library is missing build rules for big endian
ARM, and since IXP4xx is big endian ARM we need those rules to
build for IXP4xx.
Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Improve EEPROME load patches. Reorganize and rework them.
The current patch are bugged and with the case of MTD loading, leaks and
never free the EEPROM read values.
Also add support for loading EEPROM using NVMEM cells.
As a cleanup, change the binding to swap EEPROM read from mtd to
ralink,eeprom-swap and generilize it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Notable bugfixes are:
* WCN6855 board name fixes
* One MSI vector booting is working again
This is rather important for most of the older platforms.
* DFS CAC state in virtual interfaces was fixed
* TX power during CAC reporting
Signed-off-by: Robert Marko <robimarko@gmail.com>
DFS CAC time export is required for backport of a ath11k fix so lets
backport the required cfg80211 upstream commit as well.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PKG_MIRROR_HASH is wrong, fix it.
Found and fixed using this command:
make package download check FIXUP=1
Fixes: c123e4f053 ("rtl8812au-ct: bump to fix kernel 6.1 compile")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mt76 driver usually reads the eeprom on the mtd partition at dts.
For emmc device we need to use caldata_extract script to read the
eeprom. However, the default eeprom file breaks the caldata script
execution, so remove it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Package and add dependencies to drm-amdgpu and drm-radeon for 6.1
* package acpi-video, drm-display-helper and drm-buddy
* add acpi-video, drm-display-helper and drm-buddy as dependencies for
drm-amdgpu
* add acpi-video and drm-display-helper as dependencies for drm-radeon
Signed-off-by: Pascal Coudurier <coudu@gmx.com>
Synchronize the ath11k backports with the current ath-next tree.
All of the changes are various bugfixes, there is no new major feature.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit ed3725e15a154ebebf44e0c34806c57525483f92
("wifi: ath11k: Fix qmi_msg_handler data structure initialization")
has been present upstream since 6.1.2 but it seems Quilt refreshed it
wrongly so it appeared like a completely different patch.
Commit 7c15430822e71e90203d87e6d0cfe83fa058b0dc
("wifi: ath11k: allow system suspend to survive ath11k")
has been present upstream since 6.1.16 but somehow quilt still happily
applied it.
So, drop both of them.
Signed-off-by: Robert Marko <robimarko@gmail.com>
General support for 9P is desirable on platforms without virtualization.
This decouples the 9P general networking support for use on more platforms.
Signed-off-by: Daniel Maslowski <info@orangecms.org>
MAC address and interface name assigned by mac80211.sh depend on the order in
which interfaces are brought up. This order changes when interfaces get added
or removed, which can cause unnecessary reload churn.
One part of the fix it making MAC address allocation more dynamic in both
wpa_supplicant and hostapd, by ignoring the provided MAC address using
the next available one, whenever the config does not explicitly specify one.
The other part is making use of support for renaming netdevs at runtime and
preserving the MAC address for renamed netdevs.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When a device has more than one reserved mac address, they can be used for
virtual interfaces without the local bit in the first byte
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mediatek EIP93 Crypto engine is a crypto accelerator which
is available in the Mediatek MT7621 SoC.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Co-authored-by: Richard van Schagen <vschagen@icloud.com>
Co-authored-by: Chukun Pan <amadeus@jmu.edu.cn>
When switching from a STA-only configuration to AP+STA on the same phy, the
STA was previously restarted in order to notify hostapd of the new frequency,
which might not match the AP configuration.
Fix the STA restart by querying the operating frequency from within hostapd
when bringing up the AP.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It seems that this was not functioning properly and was likely completely unused.
Keeping this out of tree also introduced some annoying churn when updating, because
of the iw nl80211.h sync patch.
If this is needed, it will be reintroduced when/if it is added upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Arm platforms with the right hardware blocks (such as
GICv3.0+ interrupt controller and SMMU/IOMMU) are
able to use vfio-pci to pass through PCI devices
to a VM.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
The vfio module only exposes the enable_unsafe_noiommu_mode parameter
if CONFIG_VFIO_NOIOMMU is enabled. When it isn't, the module
will complain about an unknown parameter:
vfio: unknown parameter 'enable_unsafe_noiommu_mode' ignored
As CONFIG_VFIO_NOIOMMU is disabled by the module package,
we can remove the module loading parameter.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
vhost-net is used to accelerate traffic to virtualisation
guests that use the virtio-net network card in QEMU.
Generally it is invoked by specifying "vhost=on" to a
QEMU -netdev device:
qemu-system-aarch64 -nographic -M virt -cpu host \
--enable-kvm -bios u-boot.bin -smp 1 -m 2048 \
-drive file=openwrt-armsr-armv8.img,format=raw,index=0,media=disk \
-device "virtio-net,netdev=landev,disable-legacy=off,disable-modern=off" \
-netdev "tap,id=landev,helper=/usr/lib/qemu-bridge-helper --br=br-lan,vhost=on"
Signed-off-by: Mathew McBride <matt@traverse.com.au>