Commit Graph

1361 Commits

Author SHA1 Message Date
Lars Wessels
702366a30b lantiq: wifi mac fix for ARV752DPW
Set wifi mac from flash partition 'board_config' to
match the label on the device (Easybox 802).

Currently the wifi mac is always set to 00:0c:43:28:60:00.
eth0 and WiFi will now share the same mac (as in original firmware).

Signed-off-by: Lars Wessels <software@bytebox.org>
[improve commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-06 17:57:13 +02:00
Hauke Mehrtens
6062d85892 kernel: Update kernel 4.19 to version 4.19.131
Fixes:
- CVE-2020-10757

The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.

Run tested: ath79
Build tested: ath79

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-07-04 21:12:42 +02:00
Aleksander Jan Bajkowski
58a6f06978 lantiq: remove unused PHY drivers on xrx200
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.

Save 20.3 kB flash memory.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-06-27 00:19:13 +02:00
Petr Štetiar
e44e60b290 kernel: bump 5.4 to 5.4.48
Resolved merge conflict in the following patches:

 layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch
 ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch

Refreshed patches, removed upstreamed patch:

 bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch

Run tested: qemu-x86-64
Build tested: x86/64

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-22 12:51:22 +02:00
Adrian Schmutzler
340de1d154 lantiq: fritz7312: set maximum speed to 100 mbit on 5.4
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.

Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-21 21:30:36 +02:00
Adrian Schmutzler
ef9cee4980 lantiq: drop "CONFIG_HZ_100 is not set"
CONFIG_HZ_100 is not set to "y" in generic config anymore since
3a761c90af ("treewide: Don't diverge from upstream default HZ
settings on 4.19"), so we don't need to disable it anymore either.

This was the only remaining case in the entire tree.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-17 14:26:09 +02:00
Aleksander Jan Bajkowski
27724c2f54 lantiq: switch to 5.4
Runtime tested on BT Home Hub 5A and D-Link DWR-966.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-06-17 00:50:45 +02:00
Adrian Schmutzler
48c1fdd046 treewide: drop shebang from non-executable target files
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.

While at it, fix the executable flag on a few of these files.

This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-16 14:26:33 +02:00
Alexander Couzens
bf5d800578
lantiq: fritz 7360 v2: remove additional supported devices
The additional supported device isn't required since this is a new
device. Some board contains an addtional device,
those device were supported in earlier versions which used the
"old" image builder code.
To support an sysupgrade from such old version, there is the all caps
additional device.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:59:22 +02:00
Alexander Couzens
0962baae4e lantiq: fritz 7360 v2: rename device before it will be used
Use similiar naming scheme as ath79.
Since the fritz 7360 v2 was only in the tree for 2 days, there
is no compatibility for the old image.
Users which has installed the fritz 7360 v2 before this change, must
use sysupgrade --force to skip checks on the board.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-18 11:57:57 +02:00
Adrian Schmutzler
b24fd13024 lantiq: drop outdated kernel version switches from patches-5.4
This drops some ancient kernel version switches from patches on
lantiq target. The patch only adjusts the latest kernel 5.4, as
doing it a second time for an older kernel seems a waste of time
for a cosmetic change.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:36:21 +02:00
Yushi Nishida
78bebe680f
lantiq/xrx200: add support for the Fritzbox 7360v2
This commit adds support for the Fritzbox 7360v2

CPU: VR9 500MHz Cores: 2
RAM: 128 MB
NOR-Flash: 32 MB
WLAN: AR9287-BL1A

DECT is not working.

Thanks Sebastian Ortwein for adding 7360SL.
The dts file is derived from avm_fritz7360sl.dts.

Firmware can be flashed with this method:

1.) Set your client IP to 192.168.178.2
2.) Power on your your Fritzbox and connect to 192.168.178.1
    via ftp in the first 5 seconds.
3.) login with adam2/adam2
4.) type into the ftp prompt:

passive
binary
debug 1
quote MEDIA FLSH // (not FLASH)
put openwrt-lantiq-xrx200-avm_fritz7360v2-squashfs-sysupgrade.bin mtd1
// using the correct location for the squashfs-sysupgrade-firmware.bin

5.) wait till red light flashing turns off.
6.) type: exit

Run tested with kernel 4.19 and 5.4 on Fritzbox 7360 V2.

Issue:
Ethernet speed is slow, (iperf between a Xiaomi mir3g
and this router results in <80Mbits throughput
with a wired cable when using the gbit ports.)

Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
2020-05-16 04:37:55 +02:00
Alexander Couzens
36f628910b lantiq/fritz 7312: set maximum speed to 100 mbit
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2020-04-21 00:01:49 +02:00
Petr Štetiar
5ecc0cfd6f kernel: bump 5.4 to 5.4.28
Changelog since 5.4.24 mentions CVE-2019-19769, CVE-2020-8648,
CVE-2020-8649 and CVE-2020-8647.

Removed upstreamed:

 generic: 507-v5.6-iio-chemical-sps30-fix-missing-triggered-buffer-depe.patch
 generic: 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
 bcm27xx: 950-0435-ASoC-pcm512x-Fix-unbalanced-regulator-enable-call-in.patch
 ipq806x: 701-stmmac-fix-notifier-registration.patch
 lantiq: 002-pinctrl-falcon-fix-syntax-error.patch
 octeontx: 0002-net-thunderx-workaround-BGX-TX-Underflow-issue.patch

Run tested: apu2, qemu-x86-64, apalis, a64-olinuxino, nbg6617
Build tested: sunxi/a53, imx6, x86/64, ipq40xx

Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Sungbo Eo
3f14f034fb treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 20:02:55 +01:00
Sungbo Eo
5b392c7119 treewide: gather DEVICE_VARS into one place
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.

For ramips, remove redundant values already present in parent file.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:55:12 +01:00
Mathias Kresin
b66af9ac2d lantiq: kernel 5.4: enable JFFS2
We do not build images with a jffs2 rootfs, but jffs2 is still used as
filesystem for the rootfs_data.

Fixes: e3eaf57808 ("lantiq: kernel 5.4: debloat kernel config")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-17 20:36:39 +01:00
Mathias Kresin
e3eaf57808 lantiq: kernel 5.4: debloat kernel config
The etop driver is used by all targets except xrx200.

Remove the UBIFS compression support for zlib and zstd from the xway
subtarget. The hardware is EOL for a long time and it's unlikely to ever
see a board shipped with an UBIFS using these compression methods.

Remove the JFFS2 support. Support for jjfs2 images was dropped years
ago.

It shrinks the compressed kernel up to 130 KByte.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:17 +01:00
Mathias Kresin
6bf179b270 lantiq: add Linux 5.4 support as testing kernel version
Switch to the mainline Lantiq PCIe PHY driver and update the vr9.dtsi
accordingly.

The Lantiq IRQ SMP support added upstream required changes to the SoC
dtsi as well.

Following changes are made to the Lantiq kernel patches:

  0005-lantiq_etop-pass-struct-device-to-DMA-API-functions.patch
  0006-MIPS-lantiq-pass-struct-device-to-DMA-API-functions.patch
    applied upstream

  0008-MIPS-lantiq-backport-old-timer-code.patch
    access_ok API update because it lost it's type (which was the first)
    parameter in upstream commit 96d4f267e40f95 ("Remove 'type' argument
    from access_ok() function")

  0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch
    merged into 0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch

  0024-MIPS-lantiq-revert-DSA-switch-driver-PMU-clock-chang.patch
    revert upstream changes required for upstream xrx200 ethernet and
    xrx200 (DSA) switch driver but breaking our driver

  0026-MIPS-lantiq-Add-GPHY-Firmware-loader.patch
    required for our driver but dropped upstream, add former upstream
    version

  0028-NET-lantiq-various-etop-fixes.patch
    now has to use the phy_set_max_speed API instead of modifying
    phydev->supported. Also call ltq_dma_enable_irq() in
    ltq_etop_open() based on upstream commit cc973aecf0b054 ("MIPS:
    lantiq: Do not enable IRQs in dma open")

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-03-16 22:28:17 +01:00
Martin Blumenstingl
3d5d56487d lantiq: linux 5.4: remove support for the linux,mtd-name OF property
This is referenced in two .dts but never actually used from userspace.
Drop support for this property because it's not used and because it
makes updating to Linux 5.4 harder (as the patch doesn't apply anymore).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2020-03-16 22:28:16 +01:00
Mathias Kresin
005dedd348 lantiq: copy target to kernel 5.4
Duplicate kernel 4.19 config and patches for kernel 5.4.

Duplicate the devicetree source files as well, they need kernel 5.4
specific adjustments.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:16 +01:00
Mathias Kresin
0270b1995b lantiq: vgv7510kw22: fix missing wireless
For some reason pin 7 (gphy0_led1_pins) need to be set to output prior
to loading the PCI driver. Otherwise the wireless doesn't appear on the
PCI bus. Of course, it doesn't make much sense, since pin 7 is used to
drive the LAN1 led.

It can either be done by setting the pins function to GPHY or GPIO +
direction output. However, the pinctrl driver doesn't provide a way to
switch a pin to GPIO. It is done indirectly by the pinctrl driver at the
time a GPIO is requested (requesting a GPIO always resets the function
to GPIO).

Do it via pinmux driver, as it is always loaded first. Use the GPHY
function as it's the pins intended purpose for this board.

Fixes: FS#2895

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-16 22:28:16 +01:00
Petr Štetiar
9ba09653ad treewide: remove maintainer variable from targets
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.

Lets make it clear, that it is solely a community doing the maintenance
tasks.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
2020-03-16 22:21:45 +01:00
Mathias Kresin
f2d976f06e lantiq: move mux for pins into subnodes
The mux need to be defined in a subnode to be considered by the pinctrl
framework. These muxes aren't set as expected and might cause not
working subsystems.

Fixes: 8e7b573b7a ("lantiq: dts: assign the PCI pins to the PCI controller node")
Fixes: dcb5e52209 ("lantiq: dts: assign the STP pins to the STP GPIO controller node")
Fixes: 660200e53d ("lantiq: dts: assign the GPHY LED pins to the Ethernet controller node")
Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-15 21:38:05 +01:00
Sungbo Eo
4caaa778f7 kernel: make kmod-i2c-core selected by dependent modules
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.

Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-13 15:40:43 +01:00
Sungbo Eo
90daff4cf8 build: image: move IMAGE_SIZE to image.mk
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.

While at it, remove duplicate KERNEL_SIZE declaration.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-11 18:25:06 +01:00
Aleksander Jan Bajkowski
84845123fe kernel: remove non-existant symbols from 4.19 config
These symbols only exist in kernel version <= 4.15

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-02-22 16:38:41 +01:00
Adrian Schmutzler
2dc0a8c180 lantiq: tidy up image/Makefile
This harmonizes indent for Build blocks and removes multiple empty
lines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:52:41 +01:00
Adrian Schmutzler
719e106855 lantiq: fix setting SOC to DEFAULT_SOC
This adds the missing assignment of DEFAULT_SOC to the SOC variable
by default.

Fixes: 09ee51c614 ("lantiq: define SOC only once for uniform targets")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:48:47 +01:00
Adrian Schmutzler
09ee51c614 lantiq: define SOC only once for uniform targets
In lantiq there are several subtarget where all devices have the
same value set to the SOC variable for each device individually.

This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.

This is applied to all subtargets except xway, as only the latter has
two different SOCs.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:38:53 +01:00
Adrian Schmutzler
d9a0794f8d lantiq: move DTS_DIR variable out of Device definition
The DTS_DIR variable is not a device variable, thus it should not
be set inside Device/Default but globally.

Fixes: c640370939 ("lantiq: use soc_vendor_device scheme on DTS file")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:35:25 +01:00
Adrian Schmutzler
44cb4fd5e6 lantiq: fix model name for BT Home Hub 3 Type A
The number 3 was accidentally removed from the name during split
of DEVICE_TITLE.

Fixes: fd66687058 ("lantiq: split up DEVICE_TITLE")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 18:32:11 +01:00
Adrian Schmutzler
2fe464a712 lantiq: reorganize 02_network board.d files
This reorganizes 02_network board.d files based on what's done for
ath79 and ramips: Instead of putting all settings into a single big
case, the interface/dsl/MAC address setup is put into separate
functions with a specific switch case for each of them. This makes
grouping of devices much easier and should be easier to read, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-14 22:04:44 +01:00
Adrian Schmutzler
18e089aaed lantiq: move common DSL setup into lantiq.sh
DSL setup consists of the same commands for all subtargets, so move it
into a helper function.

While at it, remove shebang from library file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-14 22:04:37 +01:00
Adrian Schmutzler
355f0444f3 lantiq: split base-files into subtargets
This splits the device-dependent base-files into subtarget directories,
like done recently for ath79 and ramips. While this increases the
overall lines of codes, it will make the code per subtarget smaller
and easier to keep track of features and devices.

While at it, several variables at the top of 02_network are removed,
as they were never changed. The values are put directly into the
function calls where they are used.

Remove unneeded LED setup from 01_leds, and remove 01_leds entirely
for falcon subtarget (as it is not used there).

Applies alphabetic reordering to device cases in base-files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-14 22:04:29 +01:00
Adrian Schmutzler
f943d84615 lantiq: use shared code for LED migration
Shared base-files package contains functions for LED migration that
are already used by several targets. Apply those also to lantiq and
drop the (redundant) local code.

While at it, reorder board names in file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-03 00:07:00 +01:00
Adrian Schmutzler
ed3e1bd2cc lantiq: remove includes of non-existent /lib/functions/lantiq.sh
lantiq.sh is still included in files which do not use it anymore.
Remove the includes.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-03 00:05:30 +01:00
Koen Vandeputte
e115fa478f kernel: bump 4.19 to 4.19.90
Refreshed all patches.

Remove upstreamed:
- 010-dmaengine-dw-dmac-implement-dma-prot.patch
- 950-0148-Increase-firmware-call-buffer-size-to-48-bytes.patch
- 950-0206-Mailbox-firmware-calls-now-use-kmalloc-2749.patch
- 402-leds-trigger-netdev-fix-handling-on-interface-rename.patch

Fixes:
- CVE-2019-19332

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Add 010-dt-bindings-dmaengine-dw-dmac-add-protection-control.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-12-24 15:34:43 +01:00
Kevin Schmidt
77e27e0f53 lantiq: enable 5ghz wifi on VR200/VR200v
Enable mt76 driver on VR200/VR200v.

Signed-off-by: Kevin Schmidt <kevin.patrick.schmidt@googlemail.com>
2019-12-23 00:04:18 +01:00
Aleksander Jan Bajkowski
692390225d lantiq: fix phys led
led2l and led2h value is incorrectly set by led3l and led3h.
Bug was introduced in commit: 863e79f8d5

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Fixes: 863e79f8d5 ("lantiq: add support for kernel 4.9")
2019-12-23 00:04:18 +01:00
Adrian Schmutzler
e2eb6d5829 lantiq: move include to parent falcon_lantiq_easy98000.dtsi
This moves the include of lantiq.dtsi from the DTS files to the
parent falcon_lantiq_easy98000.dtsi.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Adrian Schmutzler
397aa5d37d lantiq: remove ar9_lantiq_easy50810.dts
This file seems to be orphaned, no device setup existing for it.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Adrian Schmutzler
c640370939 lantiq: use soc_vendor_device scheme on DTS file
This renames lantiq DTS(I) files to follow soc_vendor_device scheme.
This will make DTS files easier to maintain.

As a side effect, DTS file name can be derived from device node
names now, only having to specify a SOC variable in Makefiles.

While at it, move files to arch/mips/boot/dts/lantiq subfolder.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Adrian Schmutzler
de6dd7a8db lantiq: split device definitions into files
This splits device definitions into several *.mk files to increase
overview.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
4c88b3b5dc lantiq: dts: assign the ASC pins to the serial controller node
Assign the ASC pins to the serial controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
8e7b573b7a lantiq: dts: assign the PCI pins to the PCI controller node
Assign the PCI pins to the PCI controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
dcb5e52209 lantiq: dts: assign the STP pins to the STP GPIO controller node
Assign the STP pins to the STP GPIO controller node instead of using
pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
660200e53d lantiq: dts: assign the GPHY LED pins to the Ethernet controller node
Assign the GPHY LED pins to the Ethernet controller node instead of
using pin hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
7298c25f74 lantiq: dts: assign the NAND pins to the nand-controller node
Assign the NAND pins to the NAND controller node instead of using pin
hogging (where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

While here, define all NAND pins (CLE, ALE, read/RD, ready busy/RDY and
CE/CS1). This means that the pinctrl subsystem knows that these pins are
in use and cannot be re-assigned as GPIOs for example.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
edb0a936f0 lantiq: dts: define the SPI pins in {amazonse,ar9,vr9}.dtsi
Define the SPI pins in the corresponding SoCs.dtsi and assign them to
the SPI controller node. All known boards use CS4 and it's likely that
this is hardcoded in bootrom so this doesn't bother with having
per-board SPI pinmux settings.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Martin Blumenstingl
b3bdfd5df5 lantiq: dts: assign the MDIO pins to the gsw node
Assign the MDIO pins to the switch node instead of using pin hogging
(where pins are assigned to the pin controller).
This is the preferred way of assigning pins upstream.

This converts amazonse, ar9 and vr9. danube is skipped because the pin
controller doesn't define a pinmux for the MDIO pins (some of the SoC
pads may be hardwired to the MDIO pins instead of being configurable).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-12-22 01:24:23 +01:00
Koen Vandeputte
88ca372b5a kernel: bump 4.19 to 4.19.88
Refreshed all patches.

Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch

Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-12-10 09:50:42 +01:00
Adrian Schmutzler
231dc26867 treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.

This removes the identifier from all DTSI files in /target/linux.

Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx

This does not touch ipq806x for now, as the bump to 4.19 is close.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-08 16:44:06 +01:00
Koen Vandeputte
f19e471f32 kernel: bump 4.19 to 4.19.86
Refreshed all patches.

Altered patches:
- 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
- 0005-mtd-physmap_of-Move-custom-initialization.patch

Remove upstreamed:
- 0001-pinctrl-gemini-Mask-and-set-properly.patch
- 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-29 09:59:49 +01:00
Manuel Kock
509894cffb lantiq: remove redundant WiFi LED on FRITZ!Box 7320
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.

Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-11-11 18:17:29 +01:00
Adrian Schmutzler
86a1f52617 lantiq: modify ath9k caldata extraction to reuse caldata.sh
In lantiq, ath9k caldata extraction is implemented to work in two
alternate "modes", the standard one and another one with swapped
byte pairs.

This rearranges the functions so "standard" use is based on the
caldata.sh library, while only a single local function is required
for the special case.

Note that while the parameter for switching between normal and swab
is removed, the size of the caldata is added to the function calls
to stay consistent.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 13:28:58 +02:00
Martin Schiller
71e04091a9 lantiq: fix dsl_control status handling.
Commit 7519a36774 ("base-files,procd: add generic service status")
introduced the generic 'status' command which broke the previous
dsl_control status output. To fix this, let's rename the "old" command
to "dslstat".

Fixes: 7519a36774 ("base-files,procd: add generic service status")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-10-15 23:23:08 +02:00
Adrian Schmutzler
48b5d08a48 treewide: use a single ath10k MAC patching function with checksum
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).

This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.

This patch adds checksum adjustments for several targets on
ath79 and lantiq.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-15 18:13:54 +02:00
Adrian Schmutzler
2c60de0e3f treewide: move MAC address patch functions to common library
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-14 12:36:02 +02:00
Adrian Schmutzler
5b6a809092 treewide: move calibration data extraction function to library
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.

Functions are renamed with more generic names to merge different
variants that only differ in their names.

Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-13 21:48:58 +02:00
Adrian Schmutzler
c1388a2deb base-files: move xor() from caldata extraction to functions.sh
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-13 19:03:57 +02:00
Martin Schiller
c5829788c9 lantiq: add set_port_link feature to xrx200-net driver
This makes it possible to configure the link attributes (aneg, duplex,
speed) of each switch ports.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-10-12 23:43:08 +02:00
Adrian Schmutzler
0aab49d234 treewide: fix hex2dec conversion for MAC address checksum offset
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.

With this patch, the variable is not converted before the check,
but only when it's used in dd.

No conversion is done for use in hexdump, as this can deal with
hex value offsets.

Fixes: b133e466b0 ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:46:13 +02:00
Adrian Schmutzler
aea3cab77a lantiq: replace backticks by $(...) and remove useless echo
This replaces deprecated backticks by more versatile $(...) syntax.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[decapitalized patch subject at submitter's request]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-09-29 00:46:13 +02:00
Martin Schiller
315405f36b lantiq-dsl: fix value of FECS counter
Instead of the nFECS value, the nFEC value (the number of corrected code words)
was mistakenly used.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-09-19 23:43:27 +02:00
Daniel Golle
ccf3bac6f3 lantiq: add device alias for Alpha ASL56026
BT Openreach ECI VDSL Modem V-2FUb/I is an alias of Alpha ASL56026 as
also stated in the original commit message adding the device
(commit 6254a2028c "lantiq: add support for the Alpha ASL56026").

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-08-22 16:26:05 +02:00
Adrian Schmutzler
0fcab46f97 lantiq: sort device definitions in image/Makefile
This sorts the device definitions in image/Makefile alphabetically
for each subtarget/block.

The order of blocks has not been touched.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-22 16:26:05 +02:00
Moritz Warning
fd66687058 lantiq: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Uses DEVICE_ALT* variables for alternative vendor/retailer names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2019-08-22 12:57:34 +02:00
David Bauer
3032bf7f89 lantiq: unify Fritz!Box LED mappings
This commit unifies the LED mapping of the AVM Fritz!Box routers, which
have a combined Power/DSL LED.

With the stock firmware, the Power LED has the following
characteristics:

 - Blink when DSL sync is being established
 - Solid when DSL sync is present

We can't completely resemble this behavior in OpenWrt. Currently, the
Power LED is completely off, when DSL sync is missing. This is not
really helpful, as a user might have the impression, that he bricked his
device.

Instead, map the Info-LED to the state of the DSL connection.
There is no consistent behavior for the Info-LED in the stock
firmware, as the user can set it's function by himself. The DSL
connection state is one possible option for the Info LED there.

Also use the red Power LED to indicate a running upgrade, in case the
board has a two-color Power LED.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-15 14:25:51 +02:00
Adrian Schmutzler
b133e466b0
treewide: convert WiFi caldata size and offset to hexadecimal
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.

Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:36:37 +02:00
Adrian Schmutzler
75bfc393ba treewide: convert MAC address location offsets to hexadecimal
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.

(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:10:12 +02:00
David Bauer
920abb9b58 lantiq: add led-upgrade alias for Fritz!Box 7412
This adds the led-upgrade alias for the AVM Fritz!Box 7412 to indicate a
running firmware upgrade.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-10 16:16:23 +02:00
David Bauer
891a700759 lantiq: enable second VPE on Fritz!Box 7412
The AVM Fritz!Box 7412 does not use the VMMC part of the Lantiq chip but
rather a proprietary solution based on the DECT chip for the FXS ports.

Therefore, the second VPE can be enabled for use with OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-10 00:48:01 +02:00
David Bauer
c12947b39e lantiq: correct Fritz!Box 7412 button logic level
The AVM FRITZ!Box 7412 buttons are both active low, which is currently
incorrectly defined in the device-tree.

This leads to the device booting directly into failsafe.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-10 00:48:01 +02:00
Koen Vandeputte
c7634180fc kernel: bump 4.19 to 4.19.62
Refreshed all patches.

Remove upstreamed:
- 023-0013-crypto-crypto4xx-fix-AES-CTR-blocksize-value.patch
- 023-0014-crypto-crypto4xx-fix-blocksize-for-cfb-and-ofb.patch
- 023-0015-crypto-crypto4xx-block-ciphers-should-only-accept-co.patch
- 950-0252-staging-bcm2835_camera-Ensure-all-buffers-are-return.patch
- 950-0253-staging-bcm2835-camera-Remove-check-of-the-number-of.patch
- 950-0254-staging-bcm2835-camera-Handle-empty-EOS-buffers-whil.patch
- 950-0489-staging-mmal-vchiq-Replace-spinlock-protecting-conte.patch
- 0021-ARM-dts-gemini-Fix-up-DNS-313-compatible-string.patch
- 049-v4.20-mips-remove-superfluous-check-for-linux.patch
- 100-MIPS-fix-build-on-non-linux-hosts.patch
- 303-MIPS-Fix-bounds-check-virt_addr_valid.patch
- 0002-usb-dwc2-use-a-longer-AHB-idle-timeout-in-dwc2_core_.patch

Altered patches:
- 950-0267-staging-vc04_services-Split-vchiq-mmal-into-a-module.patch
- 700-net-add-qualcomm-mdio-and-phy.patch

Fixes:
- CVE-2019-3846

New symbol:
- AX88796B_PHY

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-07-31 16:51:46 +02:00
Johann Neuhauser
c3c3cd5e4a lantiq: use wpad-basic for boards with enough storage
This commit selects wpad-basic for the FRITZ!Box 7312 and 7412 as
wpad-mini is only selected on boards with small flash.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
[add short description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-30 00:44:19 +02:00
Rafał Miłecki
8b4bc7abe0 treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it
can be simply accessed using $1

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2019-07-17 08:05:38 +02:00
Mathias Kresin
92b768d5f4 lantiq: fix etop compiler warnings
The following warnings are introduced by our own patches:

 lantiq_etop.c:173:1: warning: no semicolon at end of struct or union
 };
 ^
 lantiq_etop.c: In function 'ltq_etop_change_mtu':
 lantiq_etop.c:725:2: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
  int max = ETH_HLEN + VLAN_HLEN + new_mtu + ETH_FCS_LEN;
  ^~~

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:34 +02:00
Petr Štetiar
a4bdae7cf2 lantiq: dts: use generic node names
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[split out treewide patch, integrated P2812HNUF1 rename patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[merged key and led changes, use generic node name for flash, wifi and
gpio]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:34 +02:00
Mathias Kresin
617622cb3c lantiq: dts: drop falcon clock node
It is pretty ovbious a misuse of the simple-bus binding as no child has
a address.

Luckly the clock node isn't used at all so it is safe to get rid of it.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:33 +02:00
Mathias Kresin
627b97f57d lantiq: dts: drop empty falcon devicetree node
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:31 +02:00
Mathias Kresin
0c93c09e6d lantiq: dts: fix unit address mismatch warning
Set a unit address matching the reg property for the EASY98000 ethernet
node.

Fixes a unit mismatch devicetree compiler warning.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:28 +02:00
Mathias Kresin
3b215a01bb lantiq: dts: move localbus childs to dts
The localbus childs are highly board specific and need to be part of the
board dts. Otherwise we run into duplicate unit address issues if a
board has something else (NAND) connected to the bus id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:28 +02:00
Mathias Kresin
85debe661e lantiq: dts: fix vmmc unit and register address
The register address is the same for danube und vr9. The register size
is 0x400 byte for danube and 0x300 byte for vr9.

The change doesn't have an impact as the vmmc driver doesn't use the
devicetree and has hardcoded register offsets.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:28 +02:00
Mathias Kresin
5eb7e513a5 lantiq: dts: use lower case for hex values
Use only lower case for hex values to keep it consistent.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
fdcfd2b232 lantiq: dts: drop superfluous address and size cells
Fixes the following devicetree compiler warning:

  unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
2ec59c173f lantiq: dts: move partitions into partition node
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
7685ed59c5 lantiq: dts: add missing size and address cells
Add size and address cells where missing to fix the following devicetree
compiler warning:

  Warning (avoid_default_addr_size): Relying on default #address-cells value
  Warning (avoid_default_addr_size): Relying on default #size-cells value

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
e55827b7a5 lantiq: dts: fix size cells
SPI nodes only need an address and no size. Drop the size everywhere.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
35e45b742d lantiq: dts: fix malformed unit addresses
Fixes:

   Warning (unit_address_format): unit name should not have leading "0x"

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
fcac34d01d lantiq: dts: drop superfluous unit address
The cpu temperature driver has the register offset hardcode and doesn't
need a reg.

The mdio bus node is only used as a well known name and doesn't need a
reg or unit address.

syscon-reboot doesn't have a unit address or a reg either. The unit name
collides with reset-controller@10 anyway.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
4053dd3f82 lantiq: dts: add reg if unit address is set
Add the reg property if the node has an unit address. Fixes the
following device tree compiler warning:

  Warning (unit_address_vs_reg): node has a unit name, but no reg property

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:27 +02:00
Mathias Kresin
df13384c56 lantiq: dts: move memory node to board dts
The memory node is highly board specific and should be only defined in
the board dts.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-07 11:17:26 +02:00
Mathias Kresin
cb689f2723 lantiq: drop kernel 4.14 support
The current state of the kernel 4.14 support is in the openwrt-19.07
branch. No need to keep a not default used kernel in this branch.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:14 +02:00
Martin Blumenstingl
e6867a5283 lantiq: switch to kernel 4.19
Use kernel 4.19 by default.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-07-04 08:29:13 +02:00
Martin Blumenstingl
7305e2057a lantiq: 4.19: fix panic when using the DMA API
With kernel 4.19 the DMA API relies on a struct device to work properly.
Backport upstream patches which passed a struct device instead of NULL
to the DMA API.

Fixes kernel panics during boot.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Mathias Kresin
961b8efb5b lantiq: 4.19: load PCIe driver after PCI driver
In case a PCI device is physical present, the Lantiq PCI driver need to
be loaded prior to the Lantiq PCIe driver. Otherwise none of them will
work because updating the BAR 0 of a device attached to the PCIe Bus
will fail.

Till kernel commit 9667bb039bf6 ("MIPS: lantiq: remove unnecessary
of_platform_default_populate call"), the Lantiq PCI driver was probed
early in the boot process via plat_of_setup().

Since the mentioned commit, both drivers are probed via
of_platform_default_populate_init() and they are probed according to
their order in the devicetree source file.

If the Lantiq PCI driver is enabled in the devicetree, defer the probing
og the Lantiq PCIe driver till the Lantiq PCI driver is probed. Use the
presence of a PCU bus as indicater for a loaded Lantiq PCI driver.

This way we don't need to shuffle the PCI/PCIe nodes in the devicetree
source file, as they are already (correctly) ordered based on the unit
address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Martin Blumenstingl
eb72439dbb lantiq: 4.19: increase usb reset timeouts
With kernel 4.19 dwc2 would not want to initialize due to reset
timeouts, while it worked fine with 4.14.

Increase the reset timeouts to 1 second, as it was used by the old
lantiq ifxhcd usb driver.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Hauke Mehrtens
f0c740650b lantiq: make patches apply
The following patches are dropped because they are now upstreamed:
- 0002-gpio-stp-xway-Implement-get-callback.patch
  upstreamed with commit 5b9b2b5284f819 ("gpio: stp-xway: Implement get
  callback")
- 0027-01-net-phy-intel-xway-add-VR9-version-number.patch
  upstreamed with commit 5b73d9955fb4b0 ("net: phy: intel-xway: add VR9
  version number")
- 0027-02-net-phy-intel-xway-add-VR9-v1.1-phy-ids.patch
  upstreamed with commit f452518c982e57 ("net: phy: intel-xway: add VR9
  v1.1 phy ids")

The following patches were updated:
- 0018-MTD-nand-lots-of-xrx200-fixes.patch
  the mainline driver now resides in drivers/mtd/nand/raw/xway_nand.c
  (instead of drivers/mtd/nand/xway_nand.c)
- 0025-NET-MIPS-lantiq-adds-xrx200-net.patch
  the DMA API now requires a valid device to be passed to all operations
- 0028-NET-lantiq-various-etop-fixes.patch
  the DMA API now requires a valid device to be passed to all operations

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-07-04 08:29:13 +02:00
Hauke Mehrtens
eee1b34ce6 lantiq: copy target to kernel 4.19
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-07-04 08:29:13 +02:00
Mathias Kresin
030d3f48e5 lantiq: enable STP where referenced
While moving common used parts to dtsi files, the was disabled by
default but not enabled for all boards using the STP.

Fixes: f519fea4c6 ("lantiq: kernel 4.14: cleanup dts files")

Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2019-07-03 11:16:34 +02:00
Koen Vandeputte
8f6fd53db9 kernel: bump 4.14 to 4.14.122
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-06-03 12:40:53 +02:00
Alan Swanson
e7bd254ed9 lantiq: BTHOMEHUBV5A: don't power off with restart button
The restart button is currently assigned to KEY_POWER power script but
an easily accessible button immediately powering off the device is
undesirable. Switch to using new KEY_POWER2 reboot script with 5 second
seen delay.

Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
2019-05-30 11:55:50 +02:00
Stijn Segers
5cd49395d3 lantiq/xrx200: enable initramfs images
Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but
one needs an initramfs image to flash OpenWrt from stock firmware (as
described in the commit log). This patch has the initramfs image built
by default.

Thanks to blogic (for pointing to the FEATURES declaration in the target
Makefiles) and Musashino on the forum for suggesting
config/Config-images.in needed editing too. While at it, reorder the
TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically.

This patch will result in initramfs images for all lantiq subtargets
that have the ramdisk flag set. I tested on the falcon and ase
subtargets, which lack that flag, to confirm they don't produce any
initramfs images with this patch - which they do not.

Given the limited scope of the lantiq (sub)target(s), blogic indicated
this should be OK.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[fixed the wrong reference to eae6cac6a3 commit]
2019-05-15 13:34:23 +02:00
Koen Vandeputte
09050b6fe2 kernel: bump 4.14 to 4.14.118
Refreshed all patches.

Remove upstreamed:
- 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch

Altered:
- 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-05-13 19:17:41 +02:00
Petr Štetiar
bd3a18bbe4 lantiq: tdw90x0: Fix WLAN LED on TP-Link W8970 v1.2 (FS#2232)
This patch fixes disfunctional WLAN LED on TP-Link W8970. The LED was
reported working in the CC release[1], but doesn't work anymore in 18.06.2.

1. 420cb24d41

Tested-by: Damian Janarek <dzanar18@o2.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-17 14:55:32 +02:00
Martin Schiller
f3da2ebf90 lantiq: kernel 4.14: fix usb_phy1 reset status bit in vr9.dts
The status of USB PHY 1 Reset Domain is also in bit 5 of RST_STAT2.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-03-18 20:42:30 +01:00
David Bauer
5389db72e3 fritz-tools: add support for IPQ40xx platform
AVM devices based on Qualcomm IPQ40xx do not store sector health
information in the OOB area. Make this check optional to support this
platform.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:34 +01:00
Hauke Mehrtens
a18e2994df lantiq: Refresh kernel 4.14 configuration
This adds two configuration options which are getting automatically
added.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-03-10 19:05:49 +01:00
Martin Schiller
ff3cfe0848 ltq-atm/ltq-ptm: re-enable/fix reset_ppe() functionality for VR9
This patch re-enables the reset_ppe() functionality for VR9 targets by using
the new lantiq rcu subsystem. The reset sequence in the reset_ppe() function
was taken from the ppa datapath driver of lantiq UGW 7.4.1.

Additionally it adds the required reset definitions to the vr9 dtsi file.

It also prepares the reset_ppe() function calls for the other lantiq targets.

This feature is needed to be able to switch between ltq-atm/ltq-ptm driver
in ATM/PTM Auto-Mode at runtime.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-03-10 16:49:31 +01:00
Danijel Tudek
eae6cac6a3 lantiq: add support for AVM FRITZ!Box 7362 SL
Hardware:
- SoC: Lantiq VRX288
- RAM: Winbond W971GG6JB 1 Gb (128 MiB)
- Flash:
  - SPI: 8 Mb (1 MiB) for bootloader and tffs
  - NAND: 1 Gb (128 MiB) for OS
- xDSL: Lantiq VRX208
- WLAN: Atheros AR9381
- DECT: Dialog Semiconductors SC14441

Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).

Installation via FTP:
1. Use scripts/flashing/eva_ramboot.py to send initramfs-kernel.bin
to the device when powering on.
Standard AVM procedures with finding the correct IP address and
the right moment to open FTP apply here (approx. 4 seconds on 7362SL).
IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.

2. Transfer sysupgrade.bin image with scp to /tmp directory
and run sysupgrade

3. First boot might take a bit longer if linux_fs_start was set to 1,
in that case the device will reboot twice, first time it will fail to load
second kernel (overwritten by ubifs), set linux_fs_start to 0 and reboot.

OpenWrt uses the entire NAND flash. Kernel uses 4 MiB and rootfs uses
the rest of 124 MiB, overwriting everything related to FRITZ!OS - both
OS images, config and answering machine/media server data.
To return to FRITZ!OS, use AVM's recovery image.

Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
2019-03-10 16:49:31 +01:00
Danijel Tudek
5026f43559 lantiq: move common FRITZ736X bits into dtsi
Move common FRITZ736X bits into dtsi file
as a preparation for FRITZ7362SL support.

Signed-off-by: Danijel Tudek <danijel.tudek@gmail.com>
2019-03-10 16:49:31 +01:00
Andy Binder
20f48c8ae3 lantiq: add support for AVM FRITZ!Box 7412
Hardware:

SoC: Lantiq VRX 220
CPU Cores: 2x MIPS 34Kc at 500 MHz
RAM: 128 MiB 250 MHz
Storage: 128 MiB NAND flash
Ethernet: built-in Fast Ethernet switch, only port 2 is used
Wireless: Atheros AR9287-BL1A b/g/n with 2 pcb antennas
Modem: built-in A/VDSL2 modem
DECT: Dialog SC14441
LEDs: 1 two-color, 4 one-color
Buttons: 2
FXS: 1 port via TAE or RJ12 connector
Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).

Installation:

Use the eva_ramboot.py script to load an initramfs image on the
device. Run it a few seconds after turning the device on.
$ scripts/flashing eva_ramboot 192.168.178.1 bin/targets/lantiq/xrx200/openwrt-lantiq-xrx200-avm_fritz7412-initramfs-kernel.bin
If it fails to find the device try the ip address 169.254.120.1.
(Firmware updates or the recovery tool apparently change it.)

IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.

The device will load it in ram and boot it. You can reach it under
the openwrt default ip address 192.168.1.1.

Check if the key linux_fs_start is not set to 1 in tffs:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If it is set to 1, the bootloader will select the wrong set of
partitions. Restart the box and install an FritzOS upgrade or do a
recovery. Afterwards start again at step 1.

Run sysupgrade to persistently install OpenWRT.

Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.de>
Signed-off-by: Andy Binder <AndyBinder@gmx.de>
2019-03-10 16:49:31 +01:00
Christian Lamparter
33727ecea5 lantiq: enlarge ZyXEL P-2812HNU-F1 kernel partition (FS#2124)
The current snapshot release kernel with it's 2119245 Byte
size is too big to fit into the 2097152 (2MiB) area that
was set aside for the kernel. Which causes the device to
fail to boot (after an update or even during a fresh install)

 NAND read: device 0 offset 0x60000, size 0x200000
  2097152 bytes read: OK
 ## Booting kernel from Legacy Image at 80800000 ...
    Image Name:   MIPS OpenWrt Linux-4.14.98
    Created:      2019-02-13   9:37:36 UTC
    Image Type:   MIPS Linux Kernel Image (lzma compressed)
    Data Size:    2119245 Bytes = 2 MiB
    Load Address: 80002000
    Entry Point:  80002000
    Verifying Checksum ... Bad Data CRC
 ERROR: can't get kernel image!

This patch fixes the problem by enlarging the kernel partition
at the cost of the ubi/data partition behind it. The patch
also adds a KERNEL_SIZE variable to the image Makefile to
prevent silent corruptions from happening in the future.

Please note: The u-boot environment for the router also
needs to be updated. So please attach an appropriate
serial converter cable and enter the following commands
into the u-boot prompt:

 setenv nboot 'nand read 0x80800000 0x60000 0x300000; bootm 0x80800000'
 saveenv

The wiki has been updated accordingly:
<https://openwrt.org/toh/zyxel/p2812hnu-f1>

Fixes: FS#2124
Suggested-by: Mafketel (User on bugs.openwrt.org)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-06 21:58:59 +01:00
Koen Vandeputte
3662157d8b kernel: bump 4.14 to 4.14.96
Refreshed all patches.

Remove upstreamed patches:
- 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-28 18:17:32 +01:00
Martin Schiller
654124b1af lantiq/led_dsl: Fix netdev led trigger
In the upstream netdev led trigger the one mode file was replaced by 3
files named rx, tx and link. Fix the netdev trigger configuration code
to use the modified API.

This fix is based on 201058b35c ("base-files: Fix netdev led trigger")

Fixes: aa3b6a08c5 ("kernel: Replace ledtrig-netdev with upstream backport")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2019-01-27 01:04:53 +01:00
Robert Resch
53c25fa2c4 lantiq: Add support for 2nd USB port on Fritz!Box 7320 and 7330
Enable support for 2nd USB port, which is available on Fritz!Box 7320
and 7330. It was run-tested on 7320 and 7330 as well.

Signed-off-by: Robert Resch <openwrt@webnmail.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-01-26 10:42:19 +01:00
David Bauer
d4ba7bab25 lantiq: make AVM FRITZ!Box naming consistent
This commit changes the model string and device title of all AVM boards
to fit the naming of the manufacturer.

Drop all provider-specific titles as they are re-used for every device
generation by 1&1. The original AVM model name is printed on the bottom
of every devices.

Exception applies for boards which are only supported by a specific
sub-revision.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:41:26 +01:00
Koen Vandeputte
528508ae8b kernel: bump 4.14 to 4.14.95
Refreshed all patches.

Removed superseded patches:
- 0400-Revert-MIPS-smp-mt-Use-CPU-interrupt-controller-IPI-.patch

Compile-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370), x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, lantiq (xrx200, AVM 3370)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Mathias Kresin <dev@kresin.me>
Tested-by: Robert Resch <openwrt@webnmail.de>
2019-01-24 10:10:45 +01:00
Petr Štetiar
0d23fd2ab2 treewide: dts: Remove default-state=off property from all gpio LED nodes
>From the Documentation/devicetree/bindings/leds/common.txt:

- default-state : The initial state of the LED. Valid values are "on", "off",
  and "keep". If the LED is already on or off and the default-state property is
  set the to same value, then no glitch should be produced where the LED
  momentarily turns off (or on). The "keep" setting will keep the LED at
  whatever its current state is, without producing a glitch.  The default is
  off if this property is not present.

So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-12-17 08:16:28 +01:00
Andre Heider
5d501e54fc lantiq: add integer latency stat for lantiq-dsl
The current stats always have a 'ms' suffix, and they're used by luci.
Introduce dsl.latency_[down|up] values, exported in µs without suffix.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2018-12-16 00:57:19 +01:00
Petr Štetiar
9da6cd40eb apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic diag.sh
I wanted to add status LEDs support to my imx6 based board and have found out,
that I could use diag.sh script found in ramips platform, which seems to be
also shared in a few other platforms:

 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh
 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh

And @chunkeey suggested to me, that I can also add lantiq, ipq806x and
apm821xx to the list of platforms which could share this generic
diag.sh.

I've extended the base diag.sh in a way, that if it detects any of the
DTS LED aliases, then it would use the generic DTS set_led_state code.
The code in platform's diag.sh has moved to base-files package in this
commit:

 base-files: diag.sh: Make it more generic towards DTS so it could be reused

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
2018-12-06 08:42:40 +01:00
Kevin Schmidt
bce555b09b lantiq: enable FXS ports on VR200v
Disables SMP support.
Add VR200 target to keep SMP on FXS-less device variant.

Signed-off-by: Kevin Schmidt <kevin.patrick.schmidt@googlemail.com>
2018-11-26 12:30:33 +01:00
Martin Schiller
18398abe1e lantiq/basefiles: use shutdown instead of stop when the system goes down
I can't see any reason why we shouldn't use shutdown for lantiq as well.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-11-25 19:26:55 +01:00
Koen Vandeputte
02e16e9e82 kernel: bump 4.14 to 4.14.82
Refreshed all patches.

Compile-tested: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-11-22 10:49:01 +01:00
Koen Vandeputte
c764b2b531 kernel: bump 4.14 to 4.14.79
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-05 16:00:00 +01:00
Mathias Kresin
80c61c161a treewide: use wpad-basic for not small flash targets
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-16 15:07:41 +01:00
Koen Vandeputte
f983956a8b kernel: bump 4.14 to 4.14.75
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 14:45:11 +02:00
John Crispin
61b5b4971e mac80211: make ath10k-ct the default ath10k
We select ath10k-ct by default, but it is still possible to build
the upstream version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
2018-09-26 16:39:44 +02:00
Koen Vandeputte
01793e8752 kernel: bump 4.14 to 4.14.67
Refreshed all patches.

Removed upstreamed patches:
- 037-v4.18-0008-ARM-dts-BCM5301x-Fix-i2c-controller-interrupt-type.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-08-28 23:05:39 +02:00
Paul Wassi
e348ccc4e6 treewide: fix some cosmetic glitches in dts files
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
2018-08-27 19:31:17 +02:00
Mathias Kresin
c9e9a78734 lantiq: add support for upgrade led
Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh
script en par with the other implementations using devicetree aliases
to define multiple leds for boot status indication.

By default, use the boot finished led to indicate an upgrade for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-16 21:20:57 +02:00
René van Dorst
0ae9396556 treewide: convert gpio-export to platform driver
Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-04 08:39:35 +02:00
Johann Neuhauser
02d53e6a21 lantiq: add support for FritzBox 7312
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.

Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info

LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)

The Fon LED is labeled as internet in avm gpl sources.

Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)

Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC

PCIe
GPIO#21: reset (active low)

Installation:

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
  ftp> quote REBOOT

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-07-18 19:17:46 +02:00
Johann Neuhauser
f2f7802148 lantiq: etop: pass devicetree node to phy driver
Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.

This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:

&gsw {
	phy-mode = "rmii";
	phy-handle = <&phy0>;
	mtd-mac-address = <&ath9k_cal 0xa91>;
	mtd-mac-address-increment = <(-2)>;

	mdio-bus {
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0>;

		phy0: ethernet-phy@0 {
			reg = <0>;
			reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
		};
	};
};

Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
2018-07-18 19:17:46 +02:00
Mathias Kresin
cf7154db07 kernel: only optimized for size if small_flash
Add a new config option to allow to select the default compile
optimization level for the kernel.

Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.

Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.

Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.

Exceptions to the above are:

  - lantiq, where the optimization for size is only required for the
    xway_legacy subtarget but was set for the whole target
  - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
    plenty of space and an optimization for size doesn't make much sense
  - rb532, which has 128MByte flash

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-12 18:15:32 +02:00
Michael Kuron
d0b89e48d7 lantiq: enlarge AVM Fritz!Box 3370 flash
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.

Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.

Available flash space for rootfs+overlay increases from 48MB to 124MB.

Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.

Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.

Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.

Signed-off-by: Michael Kuron <m.kuron@gmx.de>
2018-07-04 01:20:02 +02:00
Mathias Kresin
f72605f70e lantiq: backport stp-xway get callback implementation
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.

Fixes: FS#1620

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-07-04 01:20:01 +02:00
Mathias Kresin
a570933999 treewide: gpio-export: add error handling
Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-28 18:39:57 +02:00
Mathias Kresin
004fe89620 lantiq: fix arcadyan vg3503j switch port indexing
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-06-21 22:00:03 +02:00
Kevin Darbyshire-Bryant
0276e1f760 lantiq: atm: fix ifx_atm driver integration
When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77
we incorrectly updated our hack integration patch that updates atm/common.c

+++ b/net/atm/common.c
@@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc
        write_unlock_irq(&vcc_sklist_lock);
 }

+struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL;
+EXPORT_SYMBOL(ifx_atm_alloc_tx);
+
 static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size)
 {
        struct sock *sk = sk_atm(vcc);

+       if (ifx_atm_alloc_tx != NULL)
+               return ifx_atm_alloc_tx(vcc, size)

The correct solution is to drop our ifx_atm_alloc_tx replacement hack
entirely and let the kernel do its thing.

In reality neither pppoatm or BR2684 interfaces actually hit this code,
so the incorrect integration would only be noticed with direct socket
calls which we are unaware of a use-case.

This is not the solution to pppoatm vc-mux failing to work which started
the whole investigation, but let's fix it up anyway.

With sincerest thanks to David Woodhouse <dwmw2@infradead.org> &
Mathias Kresin <dev@kresin.me>.

Tested-on: lantiq, BT HomeHub 5a

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-06-18 15:26:41 +02:00
Daniel Golle
0653e31270 lantiq-vdsl-fw: update to provide recent vectoring firmware
Recent Speedport firmware downloads only work over HTTPS, so the user
either needs to provide the already downloaded file or install
ustream-ssl-* as well as ca-certificates or ca-bundle.

So to get VDSL2 with vectoring on xRX200, simply run
vdsl_fw_install.sh
on the target and either provide the downloaded file as instructed or
make sure the device is connected to the Internet and can download that
HTTPS url itself.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-15 12:45:37 +02:00
Daniel Golle
8e2f8b0c83 Revert "lantiq: get rid of ltq-vdsl-fw"
This reverts commit 0938233fcd.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-06-15 12:45:37 +02:00
Stijn Tintel
e52f3e9b13 kernel: bump 4.14 to 4.14.48
Remove upstreamed patches:
generic/pending/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
generic/pending/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
generic/pending/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
lantiq/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
Update patches that no longer apply:
generic/pending/811-pci_disable_usb_common_quirks.patch
ath79/0009-MIPS-ath79-add-lots-of-missing-registers.patch

Fixes CVE-2018-6412.

Compile-tested: octeon, x86/64.
Runtime-tested: octeon, x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-06-05 22:54:00 +03:00
Sergey Ryazanov
67a3cdcbb0 kernel: enable THIN_ARCHIVES by default
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:20 +02:00
Sergey Ryazanov
bdc2b58c4b kernel: enable FUTEX_PI by default
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:12 +02:00
Sergey Ryazanov
a08b0d0c31 kernel: enable EXPORTFS by default
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:55:05 +02:00
Sergey Ryazanov
978543a246 kernel: disable DRM_LIB_RANDOM by default
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:57 +02:00
Sergey Ryazanov
ead26e9db6 kernel: disable DMA_{NOOP|VIRT}_OPS by default
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:49 +02:00
Sergey Ryazanov
f928c338ad kernel: disable ARCH_WANTS_THP_SWAP by default
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-05-22 07:54:42 +02:00
Mathias Kresin
d8b475212b lantiq: kernel 4.14: use vbus-supply devicetree property
It isn't a phy supply, as the phy is still up if the GPIO is low. It
rather is the supply for the vbus. A correct setting/definition will be
relevant as soon as USB peripheral mode is supported.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
0b62fe5ed8 lantiq: complete AVM FRITZ!Box 3370 support
Rename the image and use a compatible string which indicates that only
hardware revision 2 and higher is supported.

It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the
wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless
LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO.

The HWREV can be checked by connecting to the fritzbox right after power
on via ftp:

  ftp> quote GETENV HWSubRevision

Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash
chips are used. Usually it isn't a big deal but depending on the used
NAND flash chip, the ECC calculation is done different (and incompatible
of course).

Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND
chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND
flash chip are doing the ECC calculation in software.

Supporting both with a single DTS isn't possible. It might be possible
to add a patch selecting the ECC mode dynamicaly based on the found NAND
flash chip. But such a patch has no chance to get accepted upstream and
most likely need to be touched with every kernel update.

Instead two images are created. One for Micron NAND flash chip and one
for Hynix NAND flash chip. So far no pattern is known to identify the
used flash chip without opening the box.

Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as
input, which will cause a reboot 30sec after power on. For boards with
EVA version 2186 the installation is tricky as it has to be finished
within the 30sec time frame.

The EVA version can be checked by connecting to the fritzbox right after
power on via ftp:

  ftp> quote GETENV urlader-version

The ath9k eeprom/caldata is at a different and offset and stored in
reverse order (from the last byte to the beginning) on the flash.
Reverse the bits to bring the data into the format expected by the
ath9k driver.

Since the ath9k eeprom is stored in reverse order on flash, we can not
use the mac address from the on flash eeprom. Get the MAC address from
the tffs instead.

Within the same HW revision 5 of the Fritz!Box 3370 both version of the
vr9 SoC are used. During preparation of kernel 4.14 support, all
devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2
gphy firmware, which fixed the embedded phys for boards using the
version 1.2 of the vr9 SoC.

While at it, add a trigger to make use of the LAN LED. Setup the
build-in switch and add a hint for LuCI two show the ports in order
matching the labels on the case

Add support for the second USB port and provide the volatage GPIOs. Use
GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38.

Name the rootfs partition ubi and remove the mtd/rootfs related kernel
bootargs to use the OpenWrt autoprobing based on the partition name.

Enable sysupgrade support to allow an upgrade from a running system.
Since sysupgrade wasn't supported till now, drop image build code which
was added to allow a sysupgrade from earlier OpenWrt versions.

Build images that allow an (initial) installation via EVA bootloader.

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote SETENV linux_fs_start 0
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1
  ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
d7b7483343 lantiq: switch to kernel 4.14
Use kernel 4.14 by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-17 07:40:19 +02:00
Mathias Kresin
ef19747b6c lantiq: kernel 4.14: Remove reboot/remove reset asserts
Backport patch accepted upstream which removes the reset asserts of the
xrx200 gphy driver on reboot/remove.

While doing a global software reset, these bits are not cleared and let
some bootloader fail to initialise the GPHYs. The bootloader don't expect
these bits to be set, as they aren't during power on.

The asserts were a workaround for a wrong syscon-reboot mask. With a mask
set which includes the GPHY resets of the first reset register, the
resets of the second reset register arn't required any more.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-05-07 18:53:08 +02:00
Kevin Darbyshire-Bryant
9aa196e0f2 kernel: bump 4.9 to 4.9.96
Refresh patches, following required reworking:

ar71xx/patches-4.9/930-chipidea-pullup.patch
layerscape/patches-4.9/302-dts-support-layercape.patch
sunxi/patches-4.9/0052-stmmac-form-4-12.patch

Fixes for CVEs:
CVE-2018-1108
CVE-2018-1092

Tested on: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Arjen de Korte <build+openwrt@de-korte.org>
2018-04-26 08:53:54 +02:00
Mathias Kresin
74a0d8cd92 build: consolidate fake uImage header build commands
Merge the two existing functions and use a parameter for the type
header field.

It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-20 20:58:52 +02:00
Mathias Kresin
0c26264dee lantiq: kernel 4.14: fix vr9 reboot mask
We need to reset the GPHYs on reboot as well. Otherwise the bootloader
might have issues to reset/find the GPHYs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-04-04 09:09:51 +02:00
Hauke Mehrtens
a74fd570a2 kernel: update kernel 4.14 to 4.14.32
The following patches are now included upstream:
* 0052-MIPS-lantiq-fix-usb-clocks.patch
* 0053-MIPS-lantiq-enable-AHB-Bus-for-USB.patch
* 0060-lantiq-ase-enable-MFD-SYSCON.patch

Closes: FS#1466

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-04-03 23:26:45 +02:00
Mathias Kresin
af3a9566fe lantiq: intel-xway: add vr9 v1.1 phy support
During upstreaming the intel phy driver, support for the vr9 v1.1
embedded phys got lost. Backport the upstream send patch adding support
for the vr9 v1.1 embbeded phys to the driver.

Signed-off-by: Mathias Kresin <dev@kresin.me>

cosmetic fixes

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-03-23 20:31:49 +01:00
Thomas Nixon
8c88e23b99 lantiq: fix DM200 boot with fake uImage headers
The latest bootloader versions load the firmware into memory and call
`chk_dniimg` (defined in Netgear GPL release), which expects to find
three consecutive block-aligned uImages. Add two fake uImage headers
after the kernel to fool this check.

This wastes up to 128k of space for alignment. The alternative would be
to put the rootfs in a second uImage, but this would limit the firmware
size to 0x710000 (the number of bytes loaded and verified by the
bootloader) instead of 0x7b0000 (the size of the firmware partition).

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2018-03-18 22:22:39 +01:00
Valentin Spreckels
ac1c31c259 lantiq: fix AVM initramfs image
Create an initramfs that can be used with the EVA bootloader.

Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
2018-03-18 22:22:38 +01:00
Hauke Mehrtens
bf4aa52dbf kernel: make mtd patches apply again
This makes some of the mtd patches apply again after some generic
patches were changed.
These problems where found by build bot.

Fixes: ac9bcefa3b ("kernel: use V10 of mtd patchset adding support for "compatible" string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-03-15 00:42:41 +01:00
Martin Schiller
d84ac78d6a lantiq/xrx200: add usif support to dts files
The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead,
there is an USIF module which can either be an UART or a
SPI Controller.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-03-06 19:49:06 +01:00
Magnus Kroken
5af85dab22 kernel: bump 4.9 to 4.9.85
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
2018-03-03 12:58:55 +01:00
Felix Fietkau
a49f6565b3 kernel: m25p80: allow fallback from spi_flash_read to regular SPI transfer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-26 19:20:06 +01:00
Felix Fietkau
46c49d8381 kernel: optimize for performance by default starting with 4.14
Keep size optimizations for smaller targets that already switched

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-24 16:05:28 +01:00
Hauke Mehrtens
6eaf8b3d89 lantiq: kernel 4.14: update dts files
Updated the devicetree source files to make use of the following
upstreamed drivers:

 - xrx200 ethernet phy
 - reset controller unit
 - dwc2
 - fpi

Use our custom xrx200 ethernet phy compatible to support boards, which
have switched the vr9 revision during lifetime, with a single devicetree
source file.

By switching to the dwc2 driver + usb phy framework, we don't need to used
our custom gpio power patch and can use a fixed regulator instead.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
f519fea4c6 lantiq: kernel 4.14: cleanup dts files
Move common used parts to dtsi. Add labels to nodes and reference nodes
via labels in dts files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
82ae68be70 lantiq: kernel 4.14: fix usb
On danube the USB0 registers are at 1e101000 similar to all other lantiq
SoCs.

On Danube and AR9 the USB core is connected to the AHB bus, hence we need
to enable the AHB Bus as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
2368f7cb78 lantiq: kernel 4.14: autoselect matching vr9 rev firmware
Add a custom xrx200 ethernet phy compatible to load the firmware matching
the vr9 revision without specifing an expected revision.

We have quite a few boards in the tree were later produced ones are using
a more recent vr9. It is impossible to distinguish which revision of the
vr9 is used without opening the case and removing a heatsink for some of
them.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
a48b4ae38b lantiq: kernel 4.14: don't use CPU interrupt controller IPI IRQ domain support
This reverts kernel commit 1eed40043579 ("MIPS: smp-mt: Use CPU interrupt
controller IPI IRQ domain support"). With the patch applied, the kernel
hangs during boot if SMP is active.

The Lantiq IRQ controller gets registered first and it directly handles
the MIPS native SW1/2 and HW0 - HW5 IRQs. It looks like this controller
already registers IRQ 0 - 7 and the generic driver only gets the following
IRQs starting later.

The upstream discussion can be found at
https://www.linux-mips.org/archives/linux-mips/2017-05/msg00059.html.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
cf53f2180c lantiq: kernel 4.14: select MFD SYSCON for ase
Enable syscon to use it for the RCU MFD on Amazon SE as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens
f1d84023cb lantiq: kernel 4.14: update patches and config
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Hauke Mehrtens
5eeaba31b8 lantiq: kernel 4.14: copy patches, config and dts files
This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2018-02-20 19:25:17 +01:00
Mathias Kresin
f8a6987cd1 lantiq: make dts files and kernel config kernel version specific
Move the devicetree source files to a kernel specific directory in
preparation of adding kernel 4.14 support.

Rename the subtarget kernel config files to match a specific kernel
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
627a28eb09 lantiq: rename gphy firmware
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.

Update the u-boot lantiq Makefile to be compatible with the new names as
well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-20 19:25:17 +01:00
Mathias Kresin
188328111b treewide: move nand_do_upgrade call to platform_do_upgrade
Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated
with 30f61a34b4 ("base-files: always use staged sysupgrade").

Update the platform upgrade code to use platform_do_upgrade() for NAND
images as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 14:44:02 +01:00
Mathias Kresin
c4ac02ffca treewide: remove obsolete sysupgrade watchdog kill
The watchdog kill command was meant for busybox watchdog. Busybox watchdog
was replaced by the procd watchdog mid 2013 with commit df7ce9301a
("busybox: disable the watchdog utility by default"), which makes the kill
command obsolete since quite some time.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-02-16 14:44:02 +01:00
Felix Fietkau
cde71a543c build: replace uses of OpenWrt with $(VERSION_DIST)
This makes the distribution name more configurable.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-02-05 10:15:53 +01:00
Yousong Zhou
82ceb2ad2a build: add config option KERNEL_MIPS_FPU_EMULATOR
To make it more accessible for nodejs users to configure and run a build
on mips target lacking hardware fpu

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2018-01-29 15:06:53 +08:00
Mathias Kresin
d3fd38637f lantiq: create ATM/PTM interfaces with dsl as netdev name
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:

 local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
 local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
 kern.info kernel: dsl0: renamed from nas0
 kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
 local2.err br2684ctl[1667]: Could not configure interface:No such device or address

By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.

Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-10 08:08:53 +01:00
Mathias Kresin
d726187367 lantiq: fix wbmr-hp-g300h image metadata
The Annex A and Annex B version are using the same (old) userspace
boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-01-04 21:23:59 +01:00
Thomas Nixon
9fc9fbeb97 lantiq: fix dts compatible string
This was broken in 7bab49fd ("lantiq: add compatible strings to dts
files"), causing for the dm200 garbled serial output during boot, and
likely other issues.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
[fix the compat string of the P2601HNFX as well]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-29 22:32:26 +01:00
Martin Schiller
94952636e7 lantiq: remove DSL_ChipSetHWVersion from status information
The value DSL_ChipSetHWVersion is fetched from the dsl frontend
via the dsl_control service, but not really provided by the dsl
frontend firmware and for now always "UNKNOWN".

The lantiq support told us that this information wouldn't be
provided in the foreseeable future, so let's remove this
useless "UNKNOWN" information.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2017-12-23 15:35:52 +01:00
Hauke Mehrtens
f704b643b9 kernel: Update kernel 4.9 to 4.9.70
Runtime tested on lantiq.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-12-19 22:45:27 +01:00
Mathias Kresin
4a4d957d1a lantiq: sync image filename with boardname
Use <manufacturer>_<modelname> as image name.

Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.

While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Mathias Kresin
58c6ad53a8 lantiq: drop unused variable from image build code
Remove the DEVICE_PROFILE variable. The variable isn't
used at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Mathias Kresin
7f68bd8119 lantiq: use the generic board detect
Drop the target specific detection function in favour of the generic
one provided by base-files.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Mathias Kresin
ed72540c10 lantiq: add missing model names
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Mathias Kresin
26dc65b126 lantiq: remove the former board name from device tree model
Remove the former used board name from the device model property and
use the model name as it is.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Mathias Kresin
63d7f7fc92 lantiq: use the compatible string as board name
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.

Don't add the former used boardname for boards which exists only in
master or evaluation boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Mathias Kresin
aba421432f lantiq: drop SoC name from eval boards compatible string
Keep it in the same format as used for the other eval boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Mathias Kresin
7bab49fd7a lantiq: add compatible strings to dts files
The compatible string is mandetory for devicetree source file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-16 23:33:56 +01:00
Christian Lamparter
da6fdce365 base-files: unify get_dt_led helper function
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.

This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.

Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2017-12-14 09:29:30 +01:00
Luis Araneda
575178e462 treewide: add only one device when appending to TARGET_DEVICES
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-12 18:47:26 +01:00
Mathias Kresin
ab6620e817 lantiq: dgn3500 drop worldwide suffix
Remove the WW suffix, everything without a region suffix is world wide
anyway.

While at it, normalise the image filenames by using only lower case
characters.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-11 12:43:29 +01:00
Mathias Kresin
0c7ad4e5d3 lantiq: nand: drop ubifs images
Users are confused which image type they should use and there are more
drawbacks than adavantages in using a r/w ubifs rootfs in constrast to
a read-only squashfs rootfs like:

 - less available free flash space due to better compression of squashfs
   images
 - no support for factory reset due to r/w filesystem
 - possibility to break failsafe due to r/w filesystem

Therefore, drop support for r/w ubifs rootfs images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-11 10:31:00 +01:00
Zoltan HERPAI
7b5c989ab9 merge: targets: update image generation and targets
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2017-12-08 19:41:18 +01:00
Stijn Tintel
f997478655 kernel: bump 4.9 to 4.9.67
Refresh patches.
Remove upstreamed patches:
- generic/190-1-5-e1000e-Fix-error-path-in-link-detection.patch
- generic/190-3-5-e1000e-Fix-return-value-test.patch
- generic/190-4-5-e1000e-Separate-signaling-for-link-check-link-up.patch
- generic/190-5-5-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch
- ramips/0102-MIPS-ralink-Fix-MT7628-pinmux.patch
- ramips/0103-MIPS-ralink-Fix-typo-in-mt7628-pinmux-function
Update patches that no longer apply:
- layerscape/815-spi-support-layerscape.patch
- ramips/0099-pci-mt7620.patch

Compile-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64.
Runtime-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-12-07 01:41:09 +02:00
Koen Vandeputte
62ede4f783 kernel: bump 4.9 to 4.9.63
Refreshed all patches.

Removed upstreamed parts.

Compile-tested: cns3xxx, imx6, mvebu, layerscape
Run-tested: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-11-22 20:45:52 +01:00
Daniel Gimpelevich
a6e9d146f2 lantiq: add missing macaddr retrieval for Netgear DGN3500
The MAC addresses were not being set for LAN and WAN. This will now use the
same MAC mechanism as the rest of the target.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
2017-11-08 23:25:05 +01:00
Mathias Kresin
b02b7004f8 lantiq: xway: rename nas0/ptm0 to dsl0
This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).

By using dsl0 as interface name as for the xrx200 we can get rid of a
few conditionals which were introduced because of the different default
TC-Layer in xway and xrx200.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-25 08:45:05 +02:00
Mathias Kresin
664369f6b2 lantiq: match default adsl annex and firmware
Set a default Annex matching the the annex of the selected adsl
firmware.

Set Annex B for xrx200 board which are known to have an ADSL hybrid for
Annex B.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-25 08:44:59 +02:00
Mathias Kresin
9dd2d99525 lantiq: add missing default lan interface
With removing the boards from the the default case to fix the xDSL WAN
MAC-Address, the setting for the default LAN interface wasn't added.

Fixes: 92a12c434c ("lantiq: fix avm fritz box mac addresses")

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-25 08:32:00 +02:00
Mathias Kresin
36d2884d55 lantiq: ARV752DPW22: fix wireless mac address
The ARV752DPW22 has the same generic mac address in the EEPROM as it
was already noticed for other lantiq boards using a ralink wireless.

Use the base mac address from the boardconfig partition as it is done
by the stock firmware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-18 22:12:45 +02:00
Mathias Kresin
a02a866519 lantiq: ARV752DPW22: set correct wireless led trigger
The ARV752DPW22 has a ralink based wireless and can not use the ath9k
only phy0tpt trigger.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-18 22:12:45 +02:00
Martin Schiller
2dc9c8206b lantiq: xrx200: rename nas0/ptm0 to dsl0
This change makes it possible to configure the wan/dsl ppp interface
settings independantly from the used TC-Layer (ATM/PTM).

Now you can move a device from an ADSL/ATM port to an VDSL/PTM port
without any configuration changes for example.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[use the dsl0 interface name for the default netdev trigger in 01_led,
add ip dependency]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-15 11:11:29 +02:00
Stijn Tintel
239dff6697 kernel: update and refresh patches
The lantiq patch 0028-NET-lantiq-various-etop-fixes.patch and sunxi
patch 0051-stmmac-form-4-11.patch no longer applied after applying the
the "generalize napi_complete_done()" patch.
Update them so they apply, and refresh patches while at it.

Fixes: 9aeb7ce8dc ("generic: net: generalize napi_complete_done")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-10-08 16:31:58 +03:00
Mathias Kresin
d65b1c815a lantiq: drop phy id specfic compatible string
With kernel commit 7630ea4bda18 ("Documentation: net: phy: improve
explanation when to specify the PHY ID") the purpose of using phy id
specific compatibles was clarified.

Remove the phy id specific compatibles since they are meant to be used
if the phy reports an incorrect or no phy id at all.

Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-07 20:15:03 +02:00
Mathias Kresin
a6bd7255ab lantiq: remove gen_nand compatible string
The generic nand driver fails to load with:

  gen_nand 14000000.nand-parts: platform_nand_data is missing
  gen_nand: probe of 14000000.nand-parts failed with error -22

and the xway-nand driver is used afterwards.

Drop the gen_nand compatible to get rid of the error message.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-07 20:15:03 +02:00
Thibaut VARÈNE
254061ee97 build: add mktplinkfw2 hardcoded values to makefile
This patch adds all the board-specific values currently hardcoded
in mktplinkfw2.c back to the respective device declarations in the
makefiles.

The rationale is to avoid modifying the source code every time a
new board or board variant is added.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2017-10-06 08:28:41 +02:00
Mathias Kresin
aba297b7fd lantiq: ase: enable USB and wireless
Add the missing USB related kernel config options to target config.
Enable wireless as well, wireless is supported via USB.

Fixes compile/packaging errors with the libertas wireless kernel
module.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Mathias Kresin
695645b9ac lantiq: ase: fix SPI support
Do not disable SPI in the subtarget, otherwise the SPI driver can not
be used.

Disable SPI by default and enable it in the board specific device tree
source file.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Mathias Kresin
66a0f3a397 lantiq: select PCI support in subtargets
AmazonSE and Falcon do not have support for PCI and it can't be
unselected in the subtarget kernel config. This way the enabled PCI
support is inherit from the higher level config to the subtarget.

If CONFIG_PCI is selected, PCI_SUPPORT will be autoselected as well and
all packages depending on this config symbol will be build and at least
some of them fail due to missing pci functions.

The issue can be observed if all kmods and all non-shared packages are
build. Fix the issue by enabling PCI support only in subtargets with
PCI support.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Mathias Kresin
77fee9bcce lantiq: ase: cleanup kernel config
The subtarget kernel config options CONFIG_CC_OPTIMIZE_FOR_SIZE and
CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK are already set by the target or
global kernel config.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Mathias Kresin
d7a76be980 lantiq: xway: cleanup kernel config
CONFIG_SPI_LANTIQ was replaced by CONFIG_SPI_LANTIQ_SSC with the switch
to the upstreamed driver.

All other removed subtarget kernel config options are already set by
the target specific or global kernel config.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Mathias Kresin
d3f3b817ac lantiq: xrx200: cleanup kernel config
CONFIG_MTSCHED & CONFIG_PERFCTRS were never defined in the kernel.

CONFIG_LANTIQ_PHY was replaced by CONFIG_INTEL_XWAY_PHY with the switch
to the upstreamed driver.

Add autoselected dependecies to the kernel config.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Mathias Kresin
054f01ac16 lantiq: xrx200: fix sorting of kernel config
Use the kconfig script to sort the kernel config. It makes further
changes more obvious.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Mathias Kresin
1c45d11bb3 treewide: drop obsolete kernel config options
CONFIG_GPIO_DEVRES was removed with kernel commit f9c22ec6c1c5 ("gpio:
Remove GPIO_DEVRES option") during kernel 4.9 development.

CONFIG_HAVE_BPF_JIT was removed with kernel commit 6077776b5908 ("bpf:
split HAVE_BPF_JIT into cBPF and eBPF variant") during kernel 4.7
development.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-10-04 20:08:15 +02:00
Stijn Tintel
6e48eb22b8 kernel: update 4.9 to 4.9.51
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.

Fixes the following CVEs:
- CVE-2017-14106
- CVE-2017-14497

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-09-20 23:50:55 +03:00
Stijn Tintel
d5b7215e31 kernel: update 4.9 to 4.9.49
Refresh patches.
Compile-tested on octeon and x86/64.
Runtime-tested on octeon and x86/64.

Fixes CVE-2017-11600.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-09-11 01:56:14 +02:00
Jorge Amorós
e2218ea148 lantiq: ARV7519RW22: enable PCIe
Enable PCIe to make the (still unsupported) WAVE300 wireless visible to
the system.

Signed-off-by: Jorge Amorós <joramar76@yahoo.es>
2017-09-10 08:30:23 +02:00
Vittorio Alfieri
31b5069a50 lantiq: VR200v: enable PCI
Enable PCI to make the (still unsupported) WAVE300 wireless visible to
the system.

Signed-off-by: Vittorio Alfieri <vittorio88@gmail.com>
2017-09-09 10:05:05 +02:00
Mathias Kresin
47be42c347 lantiq: fix xrx200 switch carrier state
In conditions where none of the switch ports is connected during boot,
the priv->port[i].link != priv->port[i].phydev->link condition is false
since both link values are equal (false). The carrier of the switch
netdev is never set to off and the link state reported by ip is UNKNOWN.

Turn the carrier off if none of the switch ports has a link, regardless
whether something has been changed. Add a check for a carrier to
prevent unnecessary calls to netif_carrier_off() if the carrier is
already off.

Based on a patch send by Martin Schiller.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-09-08 21:48:48 +02:00
Mathias Kresin
6b06c2fb8e lantiq: drop kernel 4.4 support
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-09-05 08:43:39 +02:00
Edward O'Callaghan
e0d6f541f7 lantiq: switch to kernel 4.9
Signed-off-by: Edward O'Callaghan <funfunctor@folklore1984.net>
2017-09-05 08:43:39 +02:00
Daniel Golle
2f0a8558be lantiq: ACMP252: clean up device modules
Install kmod-rt2800-pci instead of only the rt2x00 library.
Fixes missing wireless interface on AudioCodes AC-MP252.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-08-29 02:21:09 +02:00
Kevin Darbyshire-Bryant
364befeccf kernel: update 4.4 to 4.4.83
Refresh patches.
Minor update 704-phy-no-genphy-soft-reset.patch which was partially
accepted upstream.
Compile-tested on ar71xx.
Runtime-tested on ar71xx.

Fixes the following vulnerabilities:
- CVE-2017-7533 (4.4.80)
- CVE-2017-1000111 (4.4.82)
- CVE-2017-1000112 (4.4.82)

Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
[cleanup commit message, add compile/runtime tested]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-08-17 14:31:45 +02:00
Stijn Tintel
2d02a4f5bd kernel: update 4.9 to 4.9.44
Refresh patches.
Adapt 704-phy-no-genphy-soft-reset.patch.
Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch.
Compile-tested on brcm2708/bcm2708 and x86/64.
Runtime-tested on brcm2708/bcm2708 and x86/64.

Fixes the following vulnerabilities:
- CVE-2017-7533
- CVE-2017-1000111
- CVE-2017-1000112

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-08-17 12:34:34 +02:00
Daniel Gonzalez Cabanelas
e1f91b4a1c lantiq: fix missing otg_cap on danube platform
USB doesn't work in some danube boards because otg_cap
is missing since previous changes made on the USB-dwc2
lantiq driver. Fix it.

Tested on the ARV7518PW router.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
2017-08-09 23:20:56 +02:00
Martin Schiller
c8904e9c04 lantiq: board.d: use auto xfer_mode as default
If xfer_mode is set to auto the vdsl_cpe_control daemon assumes that
ATM should be used for ADSL and PTM for VDSL.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2017-08-06 09:22:03 +02:00
Martin Schiller
0481a2a2c5 lantiq: split up dsl_notify.sh into separate notification handlers
This makes it possible to simply add additional notification handlers
by putting new scripts in the /etc/hotplug.d/dsl directory.

the following Environment Variables are used:

(values marked with an * are only available when bonding support is
compiled in)

DSL_NOTIFICATION_TYPE with one of these values:
- DSL_STATUS
- DSL_INTERFACE_STATUS
- DSL_DATARATE_STATUS_US
- DSL_DATARATE_STATUS_DS

DSL_LINE_NUMBER=<0|1> *

If DSL_NOTIFICATION_TYPE == DSL_STATUS, these variables are set:

- DSL_XTU_STATUS=<ADSL|VDSL>
- DSL_TC_LAYER_STATUS=<ATM|EFM>
- DSL_EFM_TC_CONFIG_US=<NORMAL|PRE_EMPTION>
- DSL_EFM_TC_CONFIG_DS=<NORMAL>

If DSL_NOTIFICATION_TYPE == DSL_INTERFACE_STATUS, these variables are
set:

- DSL_INTERFACE_STATUS=<DOWN|READY|HANDSHAKE|TRAINING|UP>
- DSL_BONDING_STATUS=<INACTIVE|ACTIVE> *

If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_US, these variables are
set:

- DSL_DATARATE_US_BC0=<Upstream data rate in bit/s for Channel 0>
- DSL_DATARATE_US_BC1=<Upstream data rate in bit/s for Channel 1> *

If DSL_NOTIFICATION_TYPE == DSL_DATARATE_STATUS_DS, these variables are
set:

- DSL_DATARATE_DS_BC0=<Downstream data rate in bit/s for Channel 0>
- DSL_DATARATE_DS_BC1=<Downstream data rate in bit/s for Channel 1> *

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2017-08-06 09:22:03 +02:00
Andrea Merello
b81c04382b lantiq: fix sleep with spinlock held in xrx200 network driver
In the xrx200_close() function we call napi_disable(), that could
sleep, with priv->hw->chan[i].lock held. This could lead to deadlock
and causes the kernel to complain.

Look at the code I couldn't convince myself about why we
need to protect that specific code part with the lock. IMHO there
seems no reason to protect the refcount variables, because AFAIK
ndo_close() and ndo_open() callbacks are already called with a
semaphore held. Neither I could figure out why napi_disable() have to
be called with that lock held. The only remaining code part for
which I could guess the lock is useful for is ltq_dma_close()
function call.

This patch reduces the lock to the said function call, avoiding the
sleep-with-spinlock-held situation

Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
[fold into 0025-NET-MIPS-lantiq-adds-xrx200-net.patch, backport to
kernel 4.4]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-20 19:10:29 +02:00
Mathias Kresin
ac3e05c5d7 treewide: populate boardname and model earlier
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.

Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-15 23:13:34 +02:00
Koen Vandeputte
cd54b2d42b kernel: update kernel 4.9 to 4.9.37
- Refreshed all patches
- Removed upstreamed
- Adapted 4 patches:

473-fix-marvell-phy-initialization-issues.patch
-----------------------------------------------
Removed hunk 5 which got upstreamed

403-net-phy-avoid-setting-unsupported-EEE-advertisments.patch
404-net-phy-restart-phy-autonegotiation-after-EEE-advert.patch
--------------------------------------------------------------
Adapted these 2 RFC patches, merging the delta's from an upstream commit
(see below) which made it before these 2.

https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-
stable.git/commit/?h=v4.9.36&id=97ace183074d306942b903a148aebd5d061758f0

180-usb-xhci-add-support-for-performing-fake-doorbell.patch
-----------------------------------------------------------
- Moved fake_doorbell bitmask due to new item

Compile tested on: cns3xxx, imx6
Run tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-07-15 00:13:05 +02:00
Mathias Kresin
3dc757856c lantiq: fix typo in EASY80920.dtsi
There is no device tree property named phynmode0. Use phy-mode as it is
done for the other ethernet nodes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-07 07:18:14 +02:00
Thomas Nixon
50e3659703 lantiq: add Netgear DM200 support
Netgear DM200 is an inexpensive VDSL modem:

    CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz
    RAM: 64MiB
    Flash: 8MiB
    Ethernet: 1x100M
    DSL: VDSL2+, ADSL2+
    reset button, 3x bi-color LEDs

Serial port is 115200 baud, on the 4 pin header; pins from the bottom to
top are GND, RX, TX.

To upgrade from the vendor firmware, upload factory.img

The DM200 bootloader supports flashing over TFTP; hold the reset button
while powering on the device, and wait for the power light to start
flashing green before releasing. The device is now listening on
192.168.0.1/24, and can be sent a factory.img or a netgear image with a
TFTP put.

Once the image is loaded, it will be written to the flash, and the
device will reboot; this will take a few minutes.

Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their
own ports for this device and provided valuable feedback.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2017-07-07 07:13:24 +02:00
Mathias Kresin
08c499f865 lantiq: use img file extension for DGN3500 factory images
The Netgear UI in basic mode refuses the upgrade file if the the
fileextension is not img. The expert/advanced mode accepts any
fileextension. Use img to make it work in any case.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-07-04 16:29:01 +02:00
Piotr Dymacz
5b7f592251 build: move mktplinkfw2 related commands to image-commands.mk
There are already two targets (lantiq, ramips) which use mktplinkfw2
tool for creating images. This de-duplicates code, introduces two new
build commands: tplink-v2-header, tplink-v2-image and makes use of
them in place of old, (sub)target specific ones.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-29 10:37:36 +02:00
Stijn Tintel
880f73c327 kernel: cleanup CONFIG_SCHED_HRTICK
Remove CONFIG_SCHED_HRTICK from target configs, as it was added to the
generic config in b47fd76563.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-29 04:46:59 +02:00
Koen Vandeputte
69649a1b45 kernel: update kernel 4.9 to 4.9.34
- Refreshed all patches
- Adapted 1 (0031-mtd-add-SMEM-parser-for-QCOM-platforms.patch)

Compile tested on: brcm2708, cns3xxx, imx6
Run tested on: brcm2708, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[Compile and run tested on brcm2708]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2017-06-27 07:21:03 +02:00
Mathias Kresin
8e0d7d6574 build: move lzma2eva build step to image-commands.mk
Move it to image-commands.mk so that it can used by other targets with
eva based boards as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
d165f1f3bc kernel: move Lantiq PEF7061/7071/7072 phy driver to generic
The driver is used for boards outside the lantiq target as well. Move
it to generic to make it available for more targets.

The phy driver is included in kernel 4.8 as INTEL_XWAY_PHY.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-24 22:36:38 +02:00
Mathias Kresin
259fc1e778 lantiq: show xdsl line init status on shared dsl/internet led
On boards which don't have a distinct internet and dsl led, use the
shared LED to indicate the xdsl line state and any traffic that is
send/received via the netdev. This traffic doesn't necessarily need to
be internet traffic.

Rename the shared LED of existing configs to "dsl", to match the new
defaults. The configuration of the to be renamed LED is identical with
the new defaults.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:38:18 +02:00
Martin Schiller
03776d813c lantiq: restore netdev trigger of dsl led on line up
Allows to use a single LED for line init status indication and to show
any rx/tx activity on a synchronized dsl line.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-06-17 15:34:16 +02:00
Sergey Ryazanov
68e7a2a0b7 kernel: disable CONFIG_SG_POOL by default
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2017-06-07 18:31:10 +02:00
Tino Reichardt
e097eb27af lantiq: fix 0008-MIPS-lantiq-backport-old-timer-code.patch for Amazon-SE
The patch 0008 removes the vanilla kernel gptu.c of lantiq.
But the replacement file timer.c does not work Amazon-SE and
is also protected therefore with an CONFIG_SOC_AMAZON_SE :-)

This commit will re-activate the default vanilla kernel code
in gptu.c for Amazon-SE.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
[refresh patches and add same change for kernel 4.9]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-06-03 21:35:53 +02:00
Tino Reichardt
712ebe95f8 lantiq: add Allnet ALL0333CJ support
This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ.

Specifications:
- SoC: Amazon-SE
- RAM: 16MB
- Storage: 4MB NOR FLash
- LEDs: Power, Ethernet, DSL (Sync)
- Buttons: 1x Reset Button (not currently supported, will be done)
- 1x Ethernet-Port: 1x RJ45 10/100BaseTX
- 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+)

Installation:
- can be done via telnet+tftp or serial console
- default passwords:
  - via telnet (root:admin)
  - via webinterface http://172.16.1.254:8235/ (admin:coolwhite)

Installation via telnet / tftp:
host: # your own host must have an tftpd daemon, then do this:
host: ifconfig eth0:172 172.16.1.1 up
host: # telnet to allnet modem, root:admin
host: telnet 172.16.1.254
modem: # kill this daemon, it spams your console
modem: killall dsl_cpe_control
modem: # change to some place in ram:
modem: cd /ramdisk/tftp_upload
modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage
modem: tftp -g -r uImage 172.16.1.1
modem: # load these extra tools from your tftpd via:
modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz
modem: tftp -g -r flashwrite 172.16.1.1
modem: tftp -g -r fw_setenv 172.16.1.1
modem: tftp -g -r fw.conf 172.16.1.1
modem: ln -s fw_setenv fw_printenv
modem: chmod +x *
modem: ./fw_setenv disable_recovery y
modem: ./fw_setenv kernel_addr 0xb0010000
modem: ./flashwrite /dev/mtd/1 uImage 0

Installation via serial line at uboot:
uboot: # erase everything exept bootloader
uboot: protect on b0000000 +10000; protect on b03f0000 +10000
uboot: erase all
uboot: # get new firmware via tftp:
uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000
uboot: # copy to flash:
uboot: cp.b 0x80100000 $(kernel_addr) $(filesize)
uboot: # disable proprietary image checking:
uboot: setenv disable_recovery=y; saveenv
uboot: # reboot with LEDE ;)
uboot: reset

Ethernet works as expected, DSL syncronization does not work properly
currently, I am working on this issue.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt
995ad357f9 lantiq: enable Netgear DGN1000B image build
Enable the building of Netgear DGN1000B images. I have an
example device here, but it was not tested currently.
Also WLAN and USB is not ready in the moment.

This is just the proper way, so that developing on this
device is known to be done in the near future.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00
Tino Reichardt
9b321bc60d lantiq: add Amazon-SE subtarget
Re-Add support for the Amazon-SE subtarget on Lantiq.

Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
2017-06-03 21:14:07 +02:00