Commit Graph

1002 Commits

Author SHA1 Message Date
Alexander Müller
1623defbdb ramips: fix flash layout for TP-Link TL-WR841N v14
The config partition was missing from the flash layout of the device.

Although the stock firmware resets a corrupted config partition to the
default values, the TFTP flash with an image bigger than 0x3d0000 will
truncate the image as the bootloader only copies 0x3d0000 bytes to flash
during TFTP flashing.

Fixed by adding the config partition and shrinking the firmware
partition.

Fixes: 3fd97c522b ("ramips: add support for TP-Link TL-WR841n v14")

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
2020-07-19 02:01:06 +02:00
Mateus B. Cassiano
73e8f23579 ramips: add support for D-Link DIR-867/DIR-882 A1
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
        WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882

Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
          2 - RXD
          3 - TXD
          4 - GND

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 18:40:20 +02:00
Santiago Rodriguez-Papa
ed087cba8a ramips: add support for Linksys EA7300 v1
Specifications:

* SoC:      MediaTek MT7621A              (880 MHz 2c/4t)
* RAM:      Nanya NT5CC128M16IP-DIT       (256M DDR3-1600)
* Flash:    Macronix MX30LF1G18AC-TI      (128M NAND)
* Eth:      MediaTek MT7621A              (10/100/1000 Mbps x5)
* Radio:    MT7615N                       (2.4 GHz & 5 GHz)
            4 antennae: 1 internal and 3 non-deatachable
* USB:      3.0 (x1)
* LEDs:
    White   (x1 logo)
    Green   (x6 eth + wps)
    Orange  (x5, hardware-bound)
* Buttons:
    Reset   (x1)
    WPS     (x1)

Everything works! Been running it for a couple weeks now and haven't had
any problems. Please let me know if you run into any.

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: Santiago Rodriguez-Papa <contact@rodsan.dev>
[use v1 only, minor DTS adjustments, use LINKSYS_HWNAME and add it to
DEVICE_VARS, wrap DEVICE_PACKAGES, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-16 13:39:44 +02:00
Adrian Schmutzler
95a05b12d7 ramips: provide common definition for ELECOM WRC GS devices
Add a common definition for ELECOM WRC "GS" devices to mt7621.mk
to not repeat the same assignments five times.

To keep the naming consistent, slightly rename the DTSI and the
factory image recipe as well.

Note that elecom_wrc-1167ghbk2-s uses a slightly different build
recipe for the factory image, so we keep it separate.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> [WRC-1750GSV]
2020-07-16 13:39:44 +02:00
INAGAKI Hiroshi
a79f55e7e0 ramips: add support for ELECOM WRC-1750GS/GSV
ELECOM WRC-1750GS is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

WRC-1750GSV has the same hardware with WRC-1750GS.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from ethernet port side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-1750GS (or WRC-1750GSV) normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
   for WRC-1750GS : wrc-1750gs-squashfs-factory.bin
   for WRC-1750GSV: wrc-1750gsv-squashfs-factory.bin
4. Wait ~120 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-07-16 13:39:44 +02:00
Mathieu Martin-Borret
d7233b0a6a ramips: add support for D-Link DIR-878 A1
Specifications:

    SoC: MT7621AT
    RAM: 128MB
    Flash: 16MB NOR SPI flash
    WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
    LAN: 5x1000M
    Firmware layout is Uboot with extra 96 bytes in header
    Base PCB is AP-MTKH7-0002
    LEDs Power Green,Power Orange,Internet Green,Internet Orange
    LEDs "2.4G" Green & "5G" Green connected directly to wifi module
    Buttons Reset,WPS,WIFI

Flashing instructions:

Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.

Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1

Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-13 22:45:04 +02:00
Adrian Schmutzler
11478524a2 ramips: consolidate Netgear devices for mt7628
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.

As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.

Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-13 10:37:22 +02:00
Adrian Schmutzler
479adb0929 ramips: consolidate recipes with uimage_padhdr
There are already two very similar recipes using uimage_padhdr
in ramips target, and a third one is about to be added.

Make the recipe more generic, so redefinitions are not necessary
anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
2020-07-11 18:38:42 +02:00
Tim Thorpe
edbc8e5512 ramips: add support for Netgear R6020
This adds support for the Netgear R6020, aka Netgear AC750.

The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

MAC addresses based on vendor firmware:
LAN      *:88   0x4
WAN      *:89
WLAN2    *:88   0x4
WLAN5    *:8a   0x8004

The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-10 11:39:05 +02:00
Furkan Alaca
541faf2c93 ramips: mt7621: use lzma-loader for ra21s & rg21s
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).

Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
2020-07-08 22:52:40 +02:00
Sergei Burakov
4dc9ad4af8 ramips: add support for ZyXEL Keenetic Lite Rev.B
Device specification:

SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button

Flash instruction:

Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
2020-07-08 22:52:40 +02:00
Adrian Schmutzler
9e6257c26c ramips: move adslr_g7 in image/mt7621.mk to keep sorting
Move this device to the top to maintain alphabetic sorting in the
file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Adrian Schmutzler
7de08be913 ramips: add missing kmod-mt7615-firmware for TP-Link RE500 v1
Adding this has been overlooked when rebasing the commit prior to
merge.

Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 21:20:19 +02:00
Bjørn Mork
c1794d653c ramips: add support for ZyXEL WAP6805 (Altibox WiFi+)
Hardware
--------
SoC:   MediaTek MT7621ST
WiFi:  MediaTek MT7603
       Quantenna QT3840BC
Flash: 128M NAND
RAM:   64M
LED:   Dual colour red and green
BTN:   Reset
       WPS
Eth:   4 x 10/100/1000 connected to MT7621 internal switch
       MT7621 RGMII port connected to Quantenna module
GPIO:  Power/reset of Quantenna module

Quantenna module
----------------

The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation.  It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621.  It loads both a second uboot stage and an os
image from the MT7621 using tftp.  The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.

There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.

Serial ports
------------

Two serial ports with headers:

RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1   -  57600 8N1 - Connected to the MT7621 console

Both share pinout with many other Zyxel/Mitrastar devices:

1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND

Dual system partitions
----------------------

The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.

OpenWrt does not support this scheme and will always use the
first OS partition.  It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.

Installation from vendor firmware
---------------------------------

1. Run a DHCP server. The WAP6805 is configured as a client device
   and does not have a default static IP address. Make a note of
   which address it is assigned

2. tftp the OpenWrt initramfs-kernel.bin image to this address.
   Wait for the WAP6805 to reboot.

3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
   backup of all mtd partitions now.  The last used OEM image is
   still present in either "Kernel" or "Kernel2" at this point,
   and can be restored later if you save a copy.

4. sysupgrade to the OpenWrt sysupgrade.bin image.

Installation from U-Boot
------------------------

This requires serial console access

1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
   your tftp server directory.  Configure the server address as
   192.168.0.33/24

2. Hit ESC when the message "Hit ESC key to stop autoboot"
   appears

3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.

4. Answer Y to the question "Erase Linux in Flash then burn new
   one. Are you sure?", and answer the address/filename questions.
   Defaults:
        Input device IP (192.168.0.2)
        Input server IP (192.168.0.33)
        Input Linux Kernel filename ("ras.bin")

5. Wait until after you see the message "Done!" and power cycle
   the device.  It will hang after flashing.

6. Continue with step 3 and 4 from the vendor firmware procedure.

Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme.  These changes appear to have
broken a few things.  The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work.  The image selection
scheme is unreliable and inconsistent.  A limited U-Boot menu is
available - and used by the above U-Boot install procedure.  But
direct booting into an uploaded image does not work, neither with
ram nor with flash.  Flashing works, but requires a hard reset after
it is finished.

Reverting to OEM firmware
-------------------------

The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.

  ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin

OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required.  See above.

Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware.  But the branding features do obviously
differ.

LED controller
--------------

Hardware implementation is unknown.  The dual-color LED is controlled
by 3 GPIOs:

  4: red
  7: blinking green
 13: green

Enabling both red and green makes the LED appear yellow.

The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Emir Efe Kucuk
53a1fede1f ramips: Add support for Xiaomi Mi Router(Black,R2100)
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"

See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg

Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot

Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo

Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client

1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0

other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)

MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004

Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Davide Fioravanti
8c13ebd3ad ramips: add support for Edimax Gemini RE23S
Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH:   1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615 (4x4:4)
  - 5GHz:   1x MT7615 (4x4:4)
  - 4 antennas: 2 external detachable and 2 internal
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x Green led (Power)
  - 1x Green-Amber-Red led (Wifi)
UART:
  - 57600-8-N-1

Everything works correctly.

Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)

Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Restoring procedure tested with RE23_1.08.bin

MAC addresses
-------------
factory 0x4     *:24
factory 0x8004  *:25
Cimage  0x07    *:24
Cimage  0x0D    *:24
Cimage  0x13    *:24
Cimage  0x19    *:25

No other addresses were found in factory partition.

Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.

Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.

If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-08 13:28:17 +02:00
Christoph Krapp
ba0f4f0cfd ramips: add support for TP-Link RE500 v1
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-07 00:40:04 +02:00
Rowan Border
33fae8421e ramips: add support for TP-Link RE220 v2
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.

Specifications

MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.

Web Interface Installation

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Signed-off-by: Rowan Border <rowanjborder@gmail.com>
2020-06-30 17:23:32 +02:00
David Bauer
1ba0466d43 package: add ravpower-mcu package
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:04 +02:00
David Bauer
e959048c12 ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.

Hardware
--------
CPU:   MediaTek MT7628AN
RAM:   64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN:  MediaTek MT7628AN 2T2R b/g/n
       MediaTek MT7610E  1T1R n/ac
ETH:   1x FastEthernet
SD:    SD Card slot
USB:   USB 2.0

Custom PMIC on the I2C bus (address 0x0a).

Installation
------------

1. Press and hold down the reset button.

2. Power up the Device. Keep pressing the reset button for 10
   more seconds until the Globe LED lights up.

3. Attach your Computer to the Ethernet port. Assign yourself the
   address 10.10.10.1/24.

4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
   factory image.

5. The flashing will take around 1 minute. The device will reboot
   automatically into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:01 +02:00
Lars Wessels
dbaf0d20bb ramips: add support for WAVLINK WL-WN577A2
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):

Device specifications:

- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch

Flashing instructions (U-boot):

- Configure a TFTP server on your PC/Laptop and set its IP
  to 192.168.10.100

- Rename the OpenWrt image to firmware.bin and place it in the
  root folder of the TFTP server

- Power off (using the small sliding power switch on the left
  side) the device and connect an ethernet cable from its LAN
  or WAN port to your PC/Laptop

- Press the WPS button (and keep it pressed)

- Power on the device (using the small power switch)

- After a few seconds, when the WAN/LAN LED stops blinking
  very fast, release the WPS button

- Flashing OpenWrt takes less than a minute, system will
  reboot automatically

- After reboot the WPS LED will indicate the current OpenWrt
  running status

Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 01:08:01 +02:00
Jan Hoffmann
b1d5ab1a69 ramips: add support for NETGEAR WAC124
The WAC124 hardware appears to be identical to R6260/R6350/R6850.

SoC:   MediaTek MT7621AT
RAM:   128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI:  MediaTek MT7603 bgn 2T2R
       MediaTek MT7615 nac 4T4R
ETH:   SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB:   1x USB 2.0
BTN:   Reset, WPS
LED:   Power, Internet, WiFi, USB (all green)

Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2020-06-27 00:33:29 +02:00
Alex Lewontin
bd49f2c984 ramips: add support for Netgear R6080
This adds support for the Netgear R6080, aka Netgear AC1000.

The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.

Specification:

SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB

Installation:

Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-27 00:29:45 +02:00
Alex Lewontin
2e47a05d87 ramips: clean up Netgear R6120 code formatting
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.

Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
2020-06-23 21:56:44 +02:00
INAGAKI Hiroshi
3a8d65010d ramips: add support for ELECOM WRC-2533GST2
ELECOM WRC-2533GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 256 MiB
- Flash		: SPI-NOR 32 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from ethernet port side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-2533GST2 normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-06-21 20:56:42 +02:00
INAGAKI Hiroshi
39f2f9b1bf ramips: add MT7615 wireless support for ELECOM WRC-GST devices
ELECOM WRC-1900GST and WRC-2533GST have two MT7615 chips for 2.4/5 GHz
wireless.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
2020-06-21 20:52:30 +02:00
Pawel Dembicki
221d8a1c60 ramips: mt7621: add support for NETGEAR WAC104
NETGEAR WAC104 is an AP based on castrated R6220, without WAN
port and USB.

SoC: MediaTek MT7621ST
RAM: 128M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7612EN an+ac
MediaTek MT7603EN bgn
ETH: MediaTek MT7621ST (4x LAN)
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: 7x (3x GPIO controlled)

Installation:

Login to netgear webinterface and flash factory.img

Back to stock:

Use nmrpflash to revert stock image.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-06-12 14:13:32 +02:00
Adrian Schmutzler
fbb46b7bcc ramips: add support for Netgear EX6120
Specifications:
* SoC: MT7620A
* CPU: 580 MHz
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The device is identical to the EX6130 except
for the mains socket and the hardware ID.

Installation:
The -factory images can be flashed from the
device's web interface or via nmrpflash.

Notes:
MAC addresses were set up based on the EX6130 setup.

This is based on prior work of Adam Serbinski and Mathias Buchwald.

Tested by Mathias Buchwald.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:41:43 +02:00
Felix Fietkau
81b59efefd ramips/mediatek: select kmod-mt7615-firmware where kmod-mt7615e is selected
The new mt76 version splits out the firmware, because the driver can also be
used for MT7663/MT7613

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-06-04 21:52:57 +02:00
Alexey Dobrovolsky
0a182fcba6 ramips: add kmod-usb-dwc2 to ZyXEL Keenetic image
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.

Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-06-03 16:49:28 +02:00
J. Scott Heppler
168e4c91d8 ramips: add support for TRENDnet TEW-810DR
Specifications:

* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader

Installation:

The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended.  ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.

The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"

This may need to be altered if your hardware version is "1.1R".

The image can also be directly flashed via serial tftp:
1.  Load *.sysupgrade.bin to your tftp server directory and rename for
    convenience.
2.  Set a static ip 192.168.10.100.
3.  NIC cable to a lan port.
4.  Serial connection parameters 57600,8N1
5.  Power on the TEW-810 and press 4 for a u-boot command line prompt.
6.  Verify IP's with U-Boot command "printenv".
7.  Adjust tftp settings if needed per the tftp documentation
8.  Boot the tftp image to test the build.
9.  If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.

Notes:

The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx

Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-26 22:04:11 +02:00
INAGAKI Hiroshi
7b01567976 ramips: add alternative name for Buffalo WSR-2533DHP
Buffalo WSR-2533DHP is identical to the WSR-2533DHPL, Buffalo sold it
with renaming.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-05-24 18:14:59 +02:00
Ernst Spielmann
c3dc52e39a ramips: add support for Asus RT-N10P V3 / RT-N11P B1 / RT-N12 VP B1
Specifications:

- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)

Flash instructions:

1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.

Signed-off-by: Ernst Spielmann <endspiel@disroot.org>
[fix node/property name for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-24 18:14:59 +02:00
Richard Huynh
f3792690c4 ramips: Add support for Xiaomi Redmi Router AC2100 (RM2100)
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot

Installation:

1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0

Restore to stock:

1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white

Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.

Exploit and detailed instructions:

https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100

An implementation of CVE-2020-8597 against stock firmware version 1.0.14

This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.

As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.

The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh

Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
2020-05-20 15:26:22 +02:00
INAGAKI Hiroshi
0a05d71f6f ramips: fix initramfs image for I-O DATA mt7621 devices
This is additional fix of c998ae7f0e.

The sysupgrade image of I-O DATA MT7621 devices manufactured by MSTC
(MitraStar Technology Corp.) faced to the booting issue. This was caused
by imcomplete extraction of large kernel image by U-Boot, and this issue
is occurred in initramfs image after fixing of sysupgrade image.
So, use lzma-loader for initramfs image to fix the issue.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
2020-05-19 19:03:07 +08:00
Fabian Bläse
33b2078528 mt7621: Make ER-X-SFP factory image compatible with EP-R6
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.

The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.

The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.

This allows the factory image to be flashed on EP-R6 without TFTP.

Signed-off-by: Fabian Bläse <fabian@blaese.de>
2020-05-18 21:11:47 +02:00
Davide Fioravanti
31b49f02ca ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH:   5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615N (4x4:4)
  - 5GHz:   1x MT7615N (4x4:4)
  - 4 antennas: 3 external detachable antennas and 1 internal
USB:
  - 1x USB 3.0
  - 1x USB 2.0
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x White led (Power)
  - 6x Green leds (link lan1-lan4, link wan, wps)
  - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)

Everything works correctly.

Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.

However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).

After this, you should be back in the OEM firmware.

Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).

When the router reboots flash the “factory” OpenWrt image and this
time it should work.

After the OpenWrt installation you have to use the sysupgrade image
for future updates.

Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.

Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
 1) "kernel" and "rootfs"
 2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.

This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.

A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.

Another way to switch the boot partition is:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.

Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.

However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.

If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-17 18:44:28 +02:00
Sungbo Eo
a4e9c8f14b ramips: add support for netis WF2770
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- UART:
  - J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-17 18:41:48 +02:00
Zhijun You
46674723e1 ramips: add support for ASUS RT-AC54U
Specification:

- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0

Installation:

   Update using ASUS Firmware Restoration Tool:

1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
   to press and hold the reset button, then turning the router back on while
   keeping the reset button pressed for ~5 secs until the power LED starts
   flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
   Restoration Tool will wrongly assume that the router is not in Rescue Mode
   and will refuse to flash it): go to the Windows Control Panel and
   temporarily disable ALL other network adapters except the one you will use
   to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
   static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
   Ethernet port of the adapter you've just set up) and port 1 of the router
   (not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
   upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
   stays on

MAC assignment based on vendor firmware:

2g    0x4	label
5g    0x8004	label +4
lan   0x22	label +4
wan   0x28	label

Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-17 18:40:56 +02:00
Pawel Dembicki
426fb8cf84 ramips: add support for LB-Link BL-W1200
The BL-W1200 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612E)
- 5x 10/100/1000 Mbps Ethernet (MT7530)
- 2x external, non-detachable antennas (Wifi 2.4G/5G)
- 1x USB 2.0
- UART (R2) on PCB (57600 8n1)
- 9x LED (1 GPIO controlled), 1x button
- u-Boot bootloader

Known issues:
- No status LED. Used WPS LED during boot/failsafe/sysupgrade.

Installation:
1. Apply initramfs image via factory web-gui.
2. Install sysupgrade image.

How to revert to OEM firmware:
- sysupgrade -n -F stock_firmware.bin

Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-05-09 20:02:17 +02:00
Sungbo Eo
a5720d3276 ramips: tidy up image subtarget Makefiles
- use tab indent in image build recipes for consistency
- harmonize line wrapping

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-05-08 18:58:39 +02:00
Sungbo Eo
c5fdab84ed ramips: tidy up image Makefile
- sort recipes alphabetically
- simplify subtarget include directives

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-05-08 18:53:23 +02:00
Adrian Schmutzler
f0435d5343 ramips: rt3883: remove swconfig from individual DEVICE_PACKAGES
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.

Remove the redundant inclusions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 23:07:49 +02:00
Adrian Schmutzler
40325abe52 ramips: remove (kmod-)swconfig DEVICE_PACKAGES for Sitecom WL-351
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:59:40 +02:00
Adrian Schmutzler
1553f58a98 ramips: create common definition for I-O DATA NAND devices
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 22:37:23 +02:00
INAGAKI Hiroshi
c998ae7f0e ramips: use lzma-loader for I-O DATA mt7621 devices
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Note:
  These devices use Z-LOADER to read the kernel from NAND flash and boot
  it. Z-LOADER cannot load and start plain lzma-loader, so additional
  lzma-compression is needed.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
2020-04-27 12:22:02 +02:00
INAGAKI Hiroshi
a25bb8610f ramips: use lzma-loader for Japanese mt7621 devices
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.

This commit fixes the issue by using lzma-loader.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2020-04-27 12:22:02 +02:00
Szabolcs Hubai
ce19571004 ramips: mt7621: use lzma-loader for D-Link DIR-860L B1
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.

Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.

Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB

To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.

The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!

[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-04-27 12:22:02 +02:00
Sungbo Eo
1dedad2a00 ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:13:33 +02:00
Sungbo Eo
d16a486766 ramips: fix SUPPORTED_DEVICES for Mercury MAC1200R v2
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.

Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-26 21:10:24 +02:00
René van Dorst
ec2f7a47d3 kernel: add module to support SFP cages
Enables kernel SFP case support.

Signed-off-by: René van Dorst <opensource@vdorst.com>
2020-04-25 23:45:16 +02:00
Pawel Dembicki
08f5cac6fb ramips: mt7621: add NETGEAR R7200 as DEVICE_ALT1
Netgear R7200 is another clone of Netgear R6700v2, introduced in:
6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400")

Reported-by: Joel Pinsker, github user @joelp64
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-20 11:13:39 +01:00
Chuanhong Guo
19d9db5a96 ramips: mt7621: use lzma-loader for newifi d1/d2/thunder timecloud
These devices failed to properly extract kernel. enable lzma loader
for them.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 14:19:38 +08:00
Chuanhong Guo
1e5d014ba2 ramips: don't reuse KERNEL_DTB for lzma-loader
mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed
for our lzma loader.
This saves 15KB on mt7621 devices using uimage-lzma-loader.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-18 13:40:31 +08:00
Sungbo Eo
9169482f64 ramips: add support for ipTIME A1004ns
ipTIME A1004ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: MT7530BU
- USB: 1x 2.0
- UART:
  - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-04-18 12:35:54 +08:00
DENG Qingfang
7dc82528a2 ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation

Recovery to stock instruction:
1. Download stock firmware at
   http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware

Then repeat the instruction in edae3479e6 to install OpenWrt

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-18 11:50:57 +08:00
Chuanhong Guo
ad19751edc ramips: mt7621: enable lzma-loader for some devices
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-15 10:14:19 +08:00
Chuanhong Guo
75f19deb3a ramips: define image recipe for uncompressed uimage with loader
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 12:01:50 +08:00
Chuanhong Guo
d9e9a0e6b1 ramips: define lzma loader platform in target
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:17:47 +08:00
Chuanhong Guo
111029bea7 ramips: add missing DEVICE_VARS for lzma-loader
LOADER_TYPE is a per-device variable which should be included in
DEVICE_VARS.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-14 11:14:15 +08:00
Chuanhong Guo
d7d46da938 ramips: disable images for 4M devices
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-12 22:27:18 +08:00
Adrian Schmutzler
e8931b309f ramips: mt7621: tidy up names for Ubiquiti devices
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.

This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.

While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 13:25:42 +02:00
Yanase Yuki
e66becb490 ramips: add support for I-O DATA WN-AX2033GR
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.

Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V

This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.

Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".

Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
   https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-12 00:43:09 +02:00
Alexey Dobrovolsky
fea232ae8f ramips: use full 8MB flash on ZyXEL Keenetic
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.

WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).

[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html

Fixes: FS#2487
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")

Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
2020-04-08 22:03:40 +02:00
Pawel Dembicki
c948a4782b ramips: add support for D-Link DWR-960
The DWR-960 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610 mpcie card)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Ethernet (1 LAN) (AR8035)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem
- UART (J4) header on PCB (57600 8n1)
- 9x LED, 2x button
- JBOOT bootloader

Known issues:
- Flash is extremely slow.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-08 14:05:51 +01:00
Adrian Schmutzler
f761f4052c ramips: mt7621: harmonize naming scheme for Mikrotik
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.

This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).

This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-08 13:46:30 +02:00
Tobias Schramm
48b4aab80c ramips: mt7621: reenable rbm11g
I have a rbm11g and can confirm that the LAN port is indeed
switch port 0.

Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-08 13:42:58 +02:00
INAGAKI Hiroshi
e8787291b3 ramips: add support for Buffalo WSR-2533DHPL
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet	: 10/100/1000 Mbps
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 8x/6x (3x buttons, 2x slide-switches)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from triangle-mark
  - 57600n8
- Power		: 12VDC 1.5A

Flash instruction using initramfs image:

1. prepare the TFTP server with the initramfs image renamed to
   "linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
   the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
   and perform sysupgrade with it
5. wait ~120 seconds to complete flashing

Switch position overview:

- slide-switch1 (2x positions)
  - "AUTO"
  - "MANUAL" (not connected to gpio)

- slide-switch2 (3x positions)
  - "ROUTER"
  - "AP" (not connected to gpio)
  - "WB"

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-07 17:04:18 +02:00
Kip Porterfield
4b8d274456 ramips: add DTS triggers to USB LEDs for F9K1109v1
Alter DTS for Belkin F9K1109v1 to trigger USB leds from the echi/ochi
ports.

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2020-04-06 09:57:28 +02:00
Chuanhong Guo
838f1fbb50 ramips: mt7621: disable image for mikrotik_rbm11g
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-04-04 15:25:36 +08:00
DENG Qingfang
437aaae6ca Revert "ramips: mt7621: disable images for gehua_ghl-r-001"
This reverts commit 28080d54d2.
Support for MX25L25635F flash is fixed upstream

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
DENG Qingfang
53b66248f4 ramips: use SoC I2C instead of bitbanged for Ubiquiti ER-X-SFP
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2020-04-04 14:56:14 +08:00
Hauke Mehrtens
f46a3c7b14 ramips: Deactivate NETGEAR WNCE2001 by default
The root file system is getting too big for this device and this breaks
the ramips/rt305x build.

Do not build images for this board by default to fix this problem.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-03-29 22:36:05 +02:00
Sungbo Eo
3f14f034fb treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 20:02:55 +01:00
Sungbo Eo
5b392c7119 treewide: gather DEVICE_VARS into one place
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.

For ramips, remove redundant values already present in parent file.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-21 19:55:12 +01:00
Mathias Kresin
132ff90f1d ramips: do not add metadata to factory images
The image metadata are openwrt specific and not required for factory
images.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2020-03-17 22:17:59 +01:00
Sungbo Eo
4caaa778f7 kernel: make kmod-i2c-core selected by dependent modules
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.

Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-13 15:40:43 +01:00
Sungbo Eo
6410c30dc7 ramips: add support for TOTOLINK A3
TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
  - Switch: SoC internal

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Tested on device by JasonHCH <hsuan670629@gmail.com>

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-13 14:05:00 +01:00
Sungbo Eo
228bb84744 kernel: make kmod-ata-core selected by dependent modules
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.

Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi

While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-11 19:40:03 +01:00
Sungbo Eo
90daff4cf8 build: image: move IMAGE_SIZE to image.mk
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.

While at it, remove duplicate KERNEL_SIZE declaration.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-11 18:25:06 +01:00
David Bauer
4c8446bf39 ramips: add support for Ubiquiti UniFi nanoHD
Hardware
--------
SoC:   MediaTek MT7621AT
WiFi:  MediaTek MT7603 bgn 2T2R
       MediaTek MT7615 ac  4T4R
Flash: 32M SPI (Macronix MX25L25635F)
RAM:   128M DDR3 (Winbond W631GG6KB)
LED:   Dome (Blue / White)
BTN:   Reset

Installation
------------

These instructions were written for firmware version v3.9.27.
Downgrade if necessary.

1. Copy the OpenWrt sysupgrade image to the devices /tmp folder
   via scp. On factory defaults, user and password is "ubnt" at
   192.168.1.20/24.

2. Write the bootselect flag. Otherwise, the device might boot from the
   wrong partition. Verify the mtd partition used in the command below
   is the one labled "bs" in /proc/mtd (as this might change in the
   future).

   > dd if=/dev/zero bs=1 count=1 of=/dev/mtd4

3. Write the OpenWrt sysupgrade to the mtd partitions labled
   "kernel0" and "kernel1".

   > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6
   > dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7

4. Reboot or powercycle the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-03-10 21:54:46 +01:00
Christoph Krapp
2a18840cc7 ramips: add support for TP-Link RE210 v1
Hardware
--------

SoC:   MediaTek MT7620A
RAM:   64MB
FLASH: 8MB SPI
WLAN:  2G: MediaTek MT7620A
       5G: MediaTek MT7610EN
ETH:   1x 10/100/1000M (Atheros AR8035)
LED:   RSSI (orange/green)
       WiFi 2G (green)
       WiFi 5G (green)
       Power (green)
       System (red / green)
BTN:   Power
       Reset
       LED
       WPS

Serial
------

P1 - Tx
P2 - Rx
P3 - GND
P4 - VCC

Pin 4 is the one closest to the LAN port.

MAC overview
------------

WAN *:4c uboot 0x1fc00
2.4 *:4c uboot 0x1fc00
5   *:4e uboot 0x1fc00 +2

Installation
------------

Web interface:
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.

Serial/TFTP:
You can use initramfs for booting via RAM or flash the image directly.

Additional Notes:
If the web interface upgrade fails, you have to open your device and
attach serial console. Since the web upgrade overwrites the boot loader,
you might also brick your device.

In order to flash back to stock, the first header and U-Boot needs to be
stripped from the original firmware.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[change rssi LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-09 21:47:56 +01:00
Adrian Schmutzler
6e80df5e33 ramips: add support for NETGEAR R6700v2/AC2400
SoC: MediaTek MT7621AT
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7615N an+ac
MediaTek MT7615N bgn
ETH: MediaTek MT7621AT
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white),
USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white),
WPS Button(white)

Installation:

Login to netgear webinterface and flash factory.img

Based on a discontinued GitHub Pull Request by
kuyokushin <codenamezero@protonmail.com>

https://github.com/openwrt/openwrt/pull/2545

NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk
AC2400, Nighthawk AC2100 and already added R6800. Rest of them  should
be really easy supportable. Image for R6700v2 should work perfectly with
them. Please refer:

https://github.com/openwrt/openwrt/pull/2614

Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2]
Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[add guest led to mt7621_netgear_r6700-v2.dts end edit commit message]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-03-04 23:02:46 +01:00
Pawel Dembicki
4e9317201d ramips: mt7621: add support for Netgear R6800
This patch adds support for the Netgear R6800, aka Netgear AC1900 and
R6800-100PES.

Specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 128 MiB NAND
- RAM: 256 MiB
- Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- USB 2.0
- USB 3.0
- Serial baud rate of Bootloader and factory firmware: 57600

Known issues:
- Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off.
  Wifi on/off is not used.

Installation:
- apply factory image via stock web-gui.

Back to stock:
- nmrpflash can be used to recover to the stock Netgear firmware.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-03-04 23:02:46 +01:00
Petr Štetiar
ef3c71464a ramips: mt7620: disable images for Netgear 2700
Because openwrt-ramips-mt7620-netgear_ex2700-squashfs-factory.bin is too big.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-02 08:44:02 +01:00
Sungbo Eo
be3e98ce26 ramips: append tail to WF2881 initramfs image
Stock firmware has a vendor-defined tail at the end of uImage for image
validation. This patch enables OpenWrt installation from stock firmware
without having to access the UART console.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-02-11 15:13:52 +01:00
Sungbo Eo
cc89c5fe27 ramips: fix device name of netis WF-2881 to WF2881
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-07 14:33:17 +01:00
Sungbo Eo
e030d162f7 ramips: use nand_do_upgrade for netis WF-2881
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-02-07 14:28:50 +01:00
INAGAKI Hiroshi
867db0a283 ramips: add support for I-O DATA WN-AX1167GR2
I-O DATA WN-AX1167GR2 is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: NAND 128 MiB
- WLAN		: MediaTek MT7615D (2.4/5 GHz, 2T2R)
- Ethernet	: 5x 10/100/1000 Mbps
  - Switch	: MediaTek MT7621A (MT7530)
- LEDs/Input	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: Vcc, TX, RX, NC, GND
  - 57600 bps

Flash instruction using initramfs image:

1. Boot WN-AX1167GR2 normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新")
button to perform firmware update
4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade
image
5. Wait ~120 seconds to complete flashing

Notes:

- configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode
for MT7615D chip is not supported in mt76 driver
- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" by MSTC
(MitraStar Technology Corp.), but U-Boot doesn't
  - uImage magic (0x0 - 0x3) : 0x434F4D42 (COMB)
  - header crc32 (0x4 - 0x7) : with data length and data crc32
  - image name (0x20 - 0x37) : model ID and firmware versions
  - data length (0x38 - 0x3b): kernel + rootfs
  - data crc32 (0x3c - 0x3f) : kernel + rootfs

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2020-02-05 17:03:34 +01:00
INAGAKI Hiroshi
3c0e2aa63e ramips: add support for I-O DATA WN-DX1167R
I-O DATA WN-DX1167R is a 2.4/5 GHz band 11ac rotuer, based on MediaTek
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: NAND 128 MiB
- WLAN		: MediaTek MT7615D (2.4/5 GHz, 2T2R)
- Ethernet	: 5x 10/100/1000 Mbps
  - Switch	: MediaTek MT7621A (MT7530)
- LEDs/Input	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: Vcc, TX, RX, NC, GND
  - 57600 bps

Flash instruction using initramfs image:

1. Boot WN-DX1167R normally
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新")
button to perform firmware update
4. On the initramfs image, perform sysupgrade with squashfs-sysupgrade
image
5. Wait ~120 seconds to complete flashing

Notes:

- configuration in DeviceTree of DBDC (Dual-Band-Dual-Concurrent) mode
for MT7615D chip is not supported in mt76 driver
- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware
- stock firmware requires "customized uImage header" by MSTC
(MitraStar Technology Corp.), but U-Boot doesn't
  - uImage magic (0x0 - 0x3) : 0x434F4D43 (COMC)
  - header crc32 (0x4 - 0x7) : with data length and data crc32
  - image name (0x20 - 0x37) : model ID and firmware versions
  - data length (0x38 - 0x3b): kernel + rootfs
  - data crc32 (0x3c - 0x3f) : kernel + rootfs

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2020-02-05 17:03:27 +01:00
INAGAKI Hiroshi
be4d53bf69 ramips: extend and rename wr1201-factory-header
This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".

Custom uImage header in initramfs image is required on following
devices:

- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R

While at it, fix typo in comment.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-05 17:03:21 +01:00
Andreas Böhler
6d6f36ae78 ramips: add support for TP-Link RE200 v2
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.

Specifications
--------------

- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button

There are 2.4G and 5G LEDs in red and green which are controlled
separately.

MAC addresses
-------------

The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G  : *:0F

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.

Serial console
--------------

Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.

Additonal notes
---------------

It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-01 19:41:51 +01:00
Adrian Schmutzler
3227afbbab ramips: collect and harmonize TP-Link image variants in common file
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.

While at it, also use the common definitions for previously
independent definitions where appropriate.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-02-01 19:35:35 +01:00
Adrian Schmutzler
4ecd6510bf ramips: remove duplicate DEVICE_PACKAGES for TP-Link Archer C20i
DEVICE_PACKAGES is specified twice for the same device. Remove the
first (=older) assignment.

Fixes: 40692f0fb5 ("ramips: mt7620: select only the matching mt76 driver")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-29 20:29:27 +01:00
David Bauer
b30f2281cc ramips: add support for GL.iNet microuter-N300
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.

Additionally, set the label-mac for both the VIXMINI as well as the
microuter-N300.

Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   128M DDR2
FLASH: 16M
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-29 15:10:54 +01:00
Adrian Schmutzler
dc862be301 ramips: define SOC only once for uniform targets
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.

This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-24 17:16:11 +01:00
Steffen Förster
93a4c8afbf ramips: add support for TP-Link RE305 v1
Specification:

SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
  - 2.4GHz: MT7628AN
  - 5GHz: MT7612EN
LAN: 1x 10/100 Mbps

Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.

The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.

Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
2020-01-18 19:39:05 +01:00
Petr Štetiar
28080d54d2 ramips: mt7621: disable images for gehua_ghl-r-001
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.

So disable images for this device until its fixed.

Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-01-14 00:06:03 +01:00
Maxim Anisimov
86e7353bff ramips: add support for TP-Link Archer C20 v5
TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.

Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.

Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:

TP-Link image:             tpl.bin
OpenWRT sysupgrade image:  owrt.bin

 > dd if=tpl.bin of=boot.bin bs=131584 count=1
 > cat owrt.bin >> boot.bin

Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.

Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.

Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.

The boot.bin can now be uploaded and flashed using the web-recovery.

Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)

 > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
 > dd if=tpl.bin of=tmp.bin bs=131584 count=1
 > dd if=tmp.bin of=boot.bin bs=512 skip=1
 > cat boot.bin >> tp_recovery.bin
 > cat owrt.bin >> tp_recovery.bin

Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.

Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.

U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.

Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.

Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.

By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.

It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[adjust some node names for LEDs in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-09 17:33:57 +01:00
David Bauer
8f0effc462 ramips: disable image build for HiWiFi HC5962
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-09 12:32:16 +01:00
Adrian Schmutzler
9b0e8d0aa4 treewide: move mktplinkfw to tplink-v1-image in image-commands.mk
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.

Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.

This also moves rootfs_align as this is required as dependency.

Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
2020-01-08 16:15:29 +01:00
Yong-hyu Ban
99dd2709b8 ramips: add support for ipTIME A8004T
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.

Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7615E
  - 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
  - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
  - J9: Unknown unpopulated header.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-05 23:38:00 +01:00
Mason Clarke
6fba88de19 ramips: reduce lzma dictionary size for D-Link DIR-645
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".

This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.

Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.

The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.

An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.

Total image size with different dictionary size options:
D23 - 3973903 bytes (base)
D16 - 4113167 bytes (+3.5%  - +139264 bytes)
D12 - 4317967 bytes (+8.7%  - +344064‬ bytes)
D11 - 4383503 bytes (+10.3% - +409600 bytes)
D10 - 4461327 bytes (+12.3% - +487424 bytes)

Fixes: FS#1484
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
2020-01-05 19:36:45 +01:00
Andreas Böhler
411a666df2 ramips: fix sysupgrade image for TP-Link RE200v1
Images generated for the TP-Link RE200v1 cannot be updated using
sysupgrade, because a necessary call to append-metadata was missing.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2020-01-05 12:21:33 +01:00
Maksym Medvedev
663b1a14e5 ramips: add support for Edimax RA21S
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.

Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
  - 2.4GHz MediaTek MT7615N bgn
  - 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART:  through-hole on PCB.
   J1: 3.3V - RX - GND - TX / 57600-8N1.  3.3V is the square pad

Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234

The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.

Tested on device by @UAb5eSMn

Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-01-04 16:49:59 +01:00
Andreas Böhler
a3010a7f8d ramips: add support for TP-Link RE200 v1
TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.

Specifications
--------------

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button

There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.

Installation
------------

Web Interface
-------------

It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.

Serial console
--------------

Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.

Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.

Additional notes
----------------

MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.

*:88    Ethernet/2.4G    label, uboot 0x1fc00, userconfig 0x0158
*:89    unused           userconfig 0x0160
*:8A    5G               not present in flash

This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2019-12-31 13:23:55 +01:00
Adrian Schmutzler
58e71e322b ramips: rename MTK_SOC to SOC
This replaces MTK_SOC by the newly introduced common SOC device
variable.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-20 01:15:57 +01:00
Adrian Schmutzler
e417ff88f1 ramips: harmonize line breaks in image Makefiles
This harmonizes the line wrapping in image Makefile device
definitions, as those are frequently copy-pasted and are a common
subject of review comments. Having the treatment unifying should
reduce the cases where adjustment is necessary afterwards.

Harmonization is achieved by consistently (read "strictly")
applying certain rules:
- Never put more than 80 characters into one line
- Fill lines up (do not break after 40 chars because of ...)
- Use one tab for indent after wrapping by "\"
- Only break after pipe "|" for IMAGE variables

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-19 23:09:27 +01:00
Sungbo Eo
38bdfcdb87 ramips: add support for ipTIME A104ns
ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610EN
- Ethernet: 5x 10/100Mbps
  - Switch: SoC internal
- USB: 1x 2.0
- UART:
  - J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

In contrast to to-be-supported A1004ns, the A104ns has no usable
value in 0x1fc40 (uboot), so wan_mac needs to be calculated.
Also note that GPIOs for the LEDs really are inverted compared to
the A1004ns.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[moved state_default to device DTS, reordered properties in wmac,
added comment about wan_mac and LED GPIOs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-17 13:36:11 +01:00
DENG Qingfang
1b7199c90c ramips: add support for JCG JHR-AC876M
JCG JHR-AC876M is an AC2600M router

Hardware specs:
  SoC: MT7621AT
  2.4GHz: MT7615N 4x4 @ PCIe0
  5GHz: MT7615N 4x4 @ PCIe1
  Flash: Winbond W25Q128JVSQ 16MiB
  RAM: Nanya NT5CB128M16 256MiB
  USB 2.0 and 3.0 ports
  6 LEDs, 3 of which are connected to SoC GPIO
  Reset and WPS buttons

Flash instructions:
Stock to OpenWrt:
  Upload factory.bin in stock firmware's upgrade page,
  do not preserve settings

OpenWrt to stock:
  Push and hold the reset button for 5s while power cycling to
  enter recovery mode;
  Visit 192.168.1.1 and upload stock firmware

MAC addresses map:
  0x0004  *:1c  wlan2g/wan/label
  0x8004  *:20  wlan5g
  0xe000  *:1b  lan
  0xe006  *:1a  not used in stock fw

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-12-13 19:43:47 +01:00
Adrian Schmutzler
0bf4d681d4 ramips: allow JCG_MAXSIZE in kiB in Build/jcg-header
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.

This also changes the only occurence of the variable, for Cudy WR1000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-13 19:43:30 +01:00
Sungbo Eo
a972b1fb5f ramips: add support for ipTIME A6ns-M
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7615
  - 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- UART:
  - J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-12-13 19:42:48 +01:00
Sungbo Eo
0375c076b6 ramips: add support for ZIO FREEZIO
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
  - 2.4GHz: MT7603EN
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
  - Switch: SoC internal
- USB: 1x 3.0
- UART:
  - J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1

Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.

MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)

Installation via web interface:
1.  Access web admin page and turn on "OpenWrt UI mode".
2.  Flash sysupgrade image through LuCI, with the "Keep settings" option
    OFF.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.
    Make sure to NOT preserve settings.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-13 15:37:37 +01:00
Adrian Schmutzler
c4f6850efc ramips: remove unused DTS variable from DEVICE_VARS
The DTS variable has been removed in 402138d12d ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.

Remove it now since we are not using this variable.

This must _not_ be backported to 19.07, where the variable is still
in use.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-12 13:10:57 +01:00
Sungbo Eo
19800ac095 ramips: set uImage name of WeVO 11AC NAS and W2914NS v2
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-17 14:01:31 +01:00
Piotr Dymacz
e68539aca4 ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.

Specification:

- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)

Other:

- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
  has additional logic circuit for M.2 SIM switching. The 'sim-select'
  will work only if both SIM slots are occupied. Otherwise, always slot
  with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
  loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
  has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
  miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
  slots but setting GPIO22 to high allows PERSTn control per slot, using
  GPIO23-25 (value is inverted)

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-14 01:37:54 +01:00
Piotr Dymacz
dfecf94c20 ramips: add support for ALFA Network R36M-E4G
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)

Other:

- there is a dedicated, 4-pin connector for optional RTC module (Holtek
  HT138x) with 'enable' input, not available at the time of preparing
  support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
  jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
  variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
  work only if both slots are occupied, otherwise U-Boot will always
  select slot with SIM card inside (user can override it later, in
  user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
  U-Boot environment variable)

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the modem LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-11-13 21:45:31 +01:00
Sungbo Eo
261c746631 ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-13 16:21:59 +01:00
Frederik Noe-Sdun
0cbd2c74d0 ramips: add support for Netgear EX6130
Specifications:
* SoC: MT7620A
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M

The -factory images can be flashed from the
device's web interface or via nmrpflash.

The device seems to use base PCB as EX3700/EX3800,
but supporting AC1200 using MT7612E.

MAC adresses:
5.0 GHz  0x8004  *:9a
2.4 GHz  0x4     *:9b
lan      0x28    *:9b
wan      0x2e    *:9c

Since this is a one-port device, although wan MAC address is
set in flash, it is not used in OpenWrt setup.

Signed-off-by: Frederik Noe-Sdun <Frederik.Sdun@googlemail.com>
[rebased, extended commit message, tiny DTS style fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-08 18:16:14 +01:00
Paul Spooren
9fa061a7d3 ramips, mt7620: reproducible elecom-header uid/gid
The elecom-header renames the firmware image to v_0.0.0.bin, stores its
MD5 sum as v_0.0.0.md5 and tars both files again.

Both v_0.0.0 files are created as the build user making it harder to
reproduce.

This commit sets the owner/group of both files to root by adding extra
options to the final tar command.

Before:
0 buildbot   (101) buildbot   (102)  3932164 2019-11-05 14:43:22.000000 v_0.0.0.bin
0 buildbot   (101) buildbot   (102)       33 2019-11-05 14:43:22.000000 v_0.0.0.md5

After:
0 root         (0) root         (0)  3932164 2019-11-05 23:43:08.000000 v_0.0.0.bin
0 root         (0) root         (0)       33 2019-11-05 23:43:08.000000 v_0.0.0.md5

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-11-06 23:23:52 +01:00
Sungbo Eo
6ea5f7d44c ramips: fix MTK_SOC for RT3662 devices
rt3883.mk contains both RT3662 and RT3883 device profiles, but commit
6a104ac772 set MTK_SOC to rt3883 for all devices. This patch fixes it,
and renames dts files accordingly. And SoC compatible strings are also
appended in the dts.

Fixes: 6a104ac772 ("ramips/rt288x,rt3883: Name DTS files based on scheme")

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-11-04 15:22:54 +01:00
Kristian Evensen
5f108bbc58 ramips: add support for ZBT WE1026-H
This commit adds support for the ZBT WE1026-H, an outdoor AP with
support for adding an internal LTE modem. The detailed specs are:

* CPU: MT7620A
* 2x 10/100Mbps Ethernet (LAN port has passive PoE support).
* 16/32 MB Flash.
* 128/256 MB RAM.
* 1x USB 2.0 port.
* 1x mini-PCIe slot (only USB2.0 bus).
* 1x SIM slot (standard size).
* 1x 2.4Ghz WIFI (rt2800).
* 1x button.
* 6x LEDS (4 GPIO-controlled).
* 1x micro-SD reader.

The following have been tested and working:
- Ethernet switch
- Wifi
- Mini-PCIe slot + SIM slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or ito recover the router,
you can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address. Upload the firmware to start the recovery
process.

Notes:

* When binding the USB LED to a usbport, the LED is switched on all the
time due to the presence of an internal hub. Thus, it does not really
signal any USB-information.

* I only have the 32MB version and have only added support for this
device. However, the files are structured so that adding support for the
16MB version should be easy.

* Only the LAN port is accessible from the outside of the casing and LEDs
are not visible.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[rebased onto base-files split, minor style fixes, removed use of
USB led as power LED]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 15:10:22 +01:00
Adrian Schmutzler
65d76175a5 ramips: improve common definition for Netgear R6xxx in mt7621.mk
This patch renames and reassembles the common definition for
Netgear R6xxx devices in mt7621.mk. The following goals should be
achieved:
- Give the node a more generic name instead of adding devices to it
- Use the common definition in the (less) similar R6220 node
- Include/exclude settings into the common definition so the common
  node contains the common definitions
- Prepare for support of R6700 v2

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-11-03 14:00:04 +01:00
Paul Fertser
522d5ff428 ramips: add support for Xiaomi Mi Wi-Fi Router 3G v2
- CMIIT ID: 2019AP2581
- SoC:      MediaTek MT7621
- Flash:    16MiB NOR SPI (GigaDevice GD25Q128B)
- RAM:      128MiB DDR3 (ESMT M15T1G1664A)
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200, 8n1
- Ethernet: 3x 10/100/1000 Mbps (switched, 2xLAN + WAN)
- WIFI0:    MT7603E 2.4GHz 802.11b/g/n
- WIFI1:    MT7612E 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable "power" LED (two-coloured, yellow/blue)
            Non-programmable "internet" LED (shows WAN activity)
- Buttons:  Reset

INSTALLATION:

Bootloader won't accept any serial input unless "boot_wait" u-boot
environment variable is changed to "on". Vendor firmware (looks like
an illegal OpenWrt fork) won't accept any serial input unless
"uart_en" is set to "1". Tricks to force u-boot to use default
environment do not help as it's restricted in the same way.

With bootloader unlocked the easiest way would be to TFTP the
sysupgrade image or to sysupgrade after loading an initramfs one.

For porting the flash contents were changed externally with an SPI
programmer (after lifting Vcc flash IC pin away from the PCB).

Forum thread [0] indicates that this device is identical to "Xiaomi Mi
Router 4A Gigabit Edition".

[0] https://forum.openwrt.org/t/xiaomi-mi-router-4a-gigabit-edition-r4ag-r4a-gigabit-fully-supported-but-requires-overwriting-spi-flash-with-programmer/36685

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-10-27 12:25:56 +01:00
Gabor Varga
7c5f712e4f ramips: add support for Asus RT-AC65P
The Asus RT-AC65P router is identical with the RT-AC85P, but better to make separate images for it.

On both routers the installation can be done also via SSH:

Note: The user/password for SSH is identical with the one used in the
Web-interface.

1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt factory image via scp:
 > scp openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin admin@192.168.50.1:/tmp
4. Connect via SSH to the router.
 > ssh admin@192.168.50.1
5. Write the OpenWrt image to flash.
 > mtd-write -i
/tmp/openwrt-ramips-mt7621-asus_rt-ac65p-squashfs-factory.bin -d linux
6. Reboot the router
 > reboot

Changelog:

v3: removed [] from filename, rebased to latest master
v2: Rebased to latest master
v1: Initial release

Signed-off-by: Gabor Varga <vargagab@gmail.com>
2019-10-24 22:58:02 +02:00
Adrian Schmutzler
e4155bcc45 ramips: fix TARGET_DEVICES after UniElec rename
Device node names were updated, but updating TARGET_DEVICES
was overlooked.

Fixes: 4408723d42 ("ramips: remove RAM size from device name
for UniElec devices")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 18:36:45 +02:00
Adrian Schmutzler
4408723d42 ramips: remove RAM size from device name for UniElec devices
UniElec devices are the last ones in ramips target still having
the RAM size in device name although RAM size is auto-detected.

Remove this from device name, compatible, etc., as it's not
required and might be misleading to users and developers adding
device support copying those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:27:30 +02:00
Roger Pueyo Centelles
ac36cca012 ramips: mt7621: Alternative name KE 2P for Phicomm K2P
The Phicomm KE 2P is identical to the already supported Phicomm K2P,
renamed for the European market. Use the ALT0 buildroot tags to show
both devices.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-10-13 20:34:57 +08:00
Adrian Schmutzler
794d4b6652 treewide: remove kmod-usb-core from DEVICE_PACKAGES
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.

This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-06 21:28:49 +02:00
Adrian Schmutzler
400e56d22c ramips: apply consistent device name/compatible to ZBT-WE1026-5G
All Zbtlink ramips devices except the ZBT-WE1026-5G include the
zbt-/ZBT- prefix in their model name.

This changes ZBT-WE1026-5G to also follow that scheme.

The patch moves some block to keep alphatical order.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:08:20 +02:00
Adrian Schmutzler
b376818f97 ramips: harmonize device vendor Zbtlink
Spelling of Zbtlink varies across image definitions and DTS files.

This patch uses Zbtlink consistently and also updates the model
in DTS files to contain the vendor in all cases.

This patch is cosmetical, as there should be no dependencies on
device model name in ramips anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:08:20 +02:00
INAGAKI Hiroshi
12ab6ef5c3 ramips: add support for I-O DATA WNPR2600G
I-O DATA WNPR2600G is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Specification:

- SoC           : MediaTek MT7621A
- RAM           : DDR3 128 MiB
- Flash         : SPI-NOR 16 MiB
- WLAN          : 2.4/5 GHz 4T4R
  - 2.4 GHz     : MediaTek MT7615
  - 5 GHz       : MediaTek MT7615
- Ethernet      : 10/100/1000 Mbps
  - Switch      : MT7530 (SoC)
- LED/keys      : 4x/3x (2x buttons, 1x slide-switch)
- UART          : through-hole on PCB
  - J1: Vcc, RX, GND, TX from SoC side
  - 57600n8

Flash instruction using factory image:

1. Boot WNPR2600G normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-25 14:44:36 +08:00
INAGAKI Hiroshi
c1394dabf6 ramips: move "elx-header" to Makefile from mt7620.mk and mt7621.mk
I-O DATA WNPR2600G has an "elx-header", so move this definition to
generic makefile to use it from mt7621 subtarget.
This definition is also added to mt7621.mk in
f285e8634c, so remove it from mt7621.mk.

And added a line to cleanup used header file.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-09-25 14:44:36 +08:00
Sungbo Eo
b7ec6659a1 ramips: add support for ipTIME A3
ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-09-25 14:44:36 +08:00
Qi Jiang
93b6cc97ca ramips: add support for XiaoYu XY-C5
Hardware:
SoC:      MT7621A
Flash:    32 MiB
RAM:      512 MiB
Ethernet: built-in switch
USB:      1x USB3.0
SATA:     ASM1060, 1 SATA port

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.173.22
2. Download *-sysupgrade.bin image and rename it to firmware.img
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Turn on router,press the reset button and wait ~15 seconds
6. Release the reset button and after a short time
   the firmware should be transferred from the tftp server
7. Wait ~3 minutes to complete recovery.

Signed-off-by: Qi Jiang <rushx@live.cn>
[squash commits, add label-mac-device, fix sign-off style]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-25 14:44:36 +08:00
Nick Briggs
3df3bb0dae ramips: add support for EnGenius ESR600
The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit
Ethernet switch, a gigabit Ethernet WAN port and a USB port.

Specification:

- Bootloader:	U-Boot
- SoC:		MediaTek MT7620A (600 MHz)
- Flash:	16MB, Macronix MX25L12845E
- RAM:		64MB, Nanya NT5TU32M16DG-AC
- Serial:	115200 baud, no header, 3.3V
  		J2: Vcc (arrow), Gnd, Tx, Rx
- USB:		USB 2, 5V
- Ethernet:	5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327
- WiFi0:	5 GHz 802.11 b/g/n Ralink RT5592N
  		300 Mb/s, 2T2R
- WiFi1:	2.4 GHz 802.11 b/g/n integrated
  		300 Mb/s, 2T2R
- Antennas:	2 per radio, internal
- LEDs:		1 programmable power (amber)
  		2 programable radio (blue)
		1 programable WPS-5G (blue)
		1 non-programable WAN activity (blue)
		1 unconfigured WPS-2.4G (amber)
- Buttons:	GPIO: Reset, WPS

Installation:

Use the OEM web interface to install the ...-factory.dlf image.
Use the OpenWRT ...-sysupgrade.bin image for future upgrades.

The J2 serial port can be accessed either by soldering in a header,
standard 0.1" spacing, or by using pogo-pins against the back side.

As configured by the OEM, the U-Boot boot delay is short, however quickly
typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP"
prompt.  The TFTP client is configured by default with
     client:   192.168.99.9
     server:   192.168.99.8
     filename: uImageESR600
It will load an OpenWRT initramfs kernel with this method.

Known issues:

1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational.
LAN1 and LAN2 do not appear to power up. This issue is also present
in the Lava LR25G001.

2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED,
is not configured in the Device Tree specification.

3) The blue WAN activity LED is not configured in the Device Tree
specification as this causes the AR8327 switch to fail to initialize.

Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
[merge conflict in 02_network]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Daniel Danzberger
10c5d3dd5f ramips: mt7621: Add new device AsiaRF AP7621-NV1
SoC:    Mediatek MT7621A
CPU:    4x 880Mhz
Cache:  32 KB I-Cache and 32 KB D-Cach
        256 KB L2 Cache (shared by Dual-Core)
RAM:    DDR3 512MB 16bits BUS
FLASH:  16MB
Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN)
POE:    (1x PD, 2x PSE)
USB:    1x 3.0
PCI:    3x Mini PCIe (3 USB2.0 + 2 x UIM interface)
GPS:    Quectel L70B
SIM:    2 Slots
BTN:    Reset
LED:    - Power
        - Ethernet
        - Wifi
        - USB
UART:  UART is present as Pads with throughholes on the PCB.
       They are located on left side.
       3.3V - RX - GND - TX / 57600-8N1
       3.3V is the square pad

Installation
------------
The stock image is a modified openwrt and can be overflashed via sysupgrade -F

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
[merge conflict in mt7621.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Birger Koblitz
fde8e2e035 ramips: add support for Asus RT-AC85P
SoC:	MediaTek MT7621AT dual-core @ 880MHz
RAM:	256M (Winbond W632GG6KB-1)
FLASH:	128MB (Macronix MX30LF1G18AC-TI)
WiFi:	- 2.4GHz MediaTek MT7615N bgn
	- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB:	1 x USB 3.1 (Gen 1)
BTN:	Reset, WPS
LED:	- Power (blue)
	- 5Ghz (blue)
	- 2.4GHz (blue)
	- Internet (blue)
	- 4x LAN (blue)
	(LAN/WAN leds are not controllable by GPIOs)
UART: 	UART is present as Pads marked J4 on the PCB.
	3.3V - TX - RX - GND / 57600-8N1
	3.3V is the square pad
MAC:	The MAC address on the router-label matches the MAC of
	the 2.4 GHz WiFi.
	LAN and WAN MAC are identical: MAC_LABEL+4
	5 GHz WiFi MAC: also MAC_LABEL+4

Installation
------------
Via U-Boot tftpd:
Switch on device, within 2s press reset button and keep pressed
until power LED starts blinking slowly.
Upload factory image via tftp put, the router's ip is 192.168.1.1
and expects the client on 192.168.1.75.

The images also work on the Asus RT-AC65P models as tested by Gabor.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Tested-by: Gabor Varga <vargagab@gmail.com>
[fixed Asus -> ASUS in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Birger Koblitz
f285e8634c ramips: add support for Edimax RG21S
SoC:	MediaTek MT7621AT dual-core @ 880MHz
RAM:	256M (Nanya NT5CC128M)
FLASH:	16MB (Macronix MX25L12835F)
WiFi:	- 2.4GHz MediaTek MT7615N bgn
	- 5GHz MediaTek MT7615N nac
Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
USB:	No
BTN:	Reset, WPS
LED:	4 red LEDs, indistinguishable when casing closed
UART: 	UART is present as Pads marked J1 on the PCB.
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the OEM web-interface
(by default:http://192.168.1.1)
The sysupgrade image can be installed via TFTP from
the U-Boot bootloader. Connect ethernet port 2.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[flash node rename, EDIMAX -> Edimax, complete device model name]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-09-20 11:36:27 +02:00
Ivan Hörler
c03a328b10 ramips: add SD-Card support for Linkit Smart 7688
The Linkit Smart 7688 has a SD-Card reader that does not work with the official build of openwrt. Adding kmod-sdhci-mt7620 makes it working.

Signed-off-by: Ivan Hörler <i.hoerler@me.com>
2019-09-15 20:34:09 +02:00
Chuanhong Guo
7a21c85f70 ramips: improve support for Xiaomi Miwifi Nano
This patch does the following things:
1. mark u-boot-env writable
2. add bootcount support
   Currently, u-boot has a flag_boot_success env variable to reset.
   Also reset it in our firmware to follow the behavior in vendor's
   firmware.
3. disable usb support
   This router doesn't have usb port at all.
4. increase spi clock to 40MHz
5. fix pinmux groups

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-09-04 19:26:01 +08:00
Christoph Krapp
6cea9688af ramips: add support for Netgear R6260 and R6850
As Netgear uses the same image for R6260, R6350 & R6850
we can merge device tree files and generate separate
images for each device.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[add missing WiFi compatible string, fix network
configuration]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Christoph Krapp
3c8df280a9 ramips: add factory image for Netgear R6350
This adds factory image generation for all three
devices. These images can be flashed via WebUI
for easy installation.

Thanks to David Bauer for the inspiration.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[altered commit to only include the R6350]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Christoph Krapp
9861fa7aba ramips: add mt7615e support to Netgear R6350
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-08-31 10:31:00 +02:00
David Bauer
607dfdf211 ramips: add factory image for NETGEAR R6220
This adds an easy-installation factory image for the NETGEAR R6220
router. The factory image can either be flashed via the vendor Web-UI or
the bootloader using nmrpflash.

Tested with NETGEAR V1.1.0.86 firmware.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-31 10:31:00 +02:00
Christian Lamparter
3dc5716b07 ramips: add NAS goodies on U25AWF-H1 + U35[N|W]F
These devices are sold as a "NAS HDD Enclousure"
and have a "NAS Media Streaming & File Server & AP" on
the box. That's why I think they should have some support
for the HDD right out-of-the-box.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-08-24 23:23:31 +02:00
Zhenjian Zhang
fb3574f123 ramips: add support for ADSLR G7
SoC: MT7621AT
RAM: 256MB
Flash: 16M SPI
Ethernet: 5x GE ports
WiFi: 2.4G: MT7615N
5G: MT7615N

Flash instruction:
1.Modify the file to linux.bin
2.Set up FTP service
3.Computer settings fixed IP: 192.168.179.50 255.255.255.0
4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds.

Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com>
[fix mac location]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-08-24 08:55:33 +08:00
Daniel Golle
41f580b596 ramips: add device alias for Allnet ALL0239-3G
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-08-22 13:22:39 +02:00
Paul Spooren
149d1e7a61 ramips/mt76x8: add DEVICE_VENDOR for tl-wr840n-v5
DEVICE_VENDOR is missing for this device.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2019-08-22 12:57:34 +02:00
Sungbo Eo
2678ba9093 ramips: add support for ipTIME A604M
ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek
MT7628AN.

Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7612EN
- Ethernet: 5x 10/100Mbps
  - Switch: SoC internal
- UART:
  - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-08-17 23:52:34 +08:00
Felix Fietkau
7ec092e641 Revert faulty tree push
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-08-12 12:27:06 +02:00
Felix Fietkau
085141dc5b ramips: add preliminary support for WIO ONE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-08-12 11:43:39 +02:00
Felix Fietkau
b1db6d0539 ramips: add preliminary support for SGE AP-MTKH7-0006 developer board
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2019-08-12 11:43:39 +02:00
Ozgur Can Leonard
d7c082ba4f ramips: add kmod-mt7615e to Xiaomi Mi Router 3 Pro images
Now that the mt76/mt7615e driver is in Openwrt, might as well use it.

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
2019-08-10 00:32:28 +02:00
DENG Qingfang
d3e832d6fd ramips: add support for HiWiFi HC5761A
HiWiFi HC5761A is an "MT7628AN variant" of HC5761

Specifications:
- MediaTek MT7628AN 580MHz
- 128 MB DDR2 RAM
- 16 MB SPI Flash
- 2.4G MT7628AN 802.11bgn 2T2R 300Mbps
- 5G MT7610EN 802.11ac 433Mbps
- 3x 10/100 Mbps Ethernet

Flash instruction:
1. Get SSH access to the router
2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one
3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP
4. Run `mtd write /tmp/<filename> firmware`
5. reboot

Known bug:
- SD slot does not work (See PR 1500)

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-08-08 21:02:03 +08:00
NOGUCHI Hiroshi
a1c6a316d2 ramips: add support for Fon FON2601
FON2601 is a wireless router.

Specification:
- SoC: Mediatek MT7620A (580MHz)
- RAM: 128 MiB
- ROM: 16 MiB SPI Flash
- Wireless:
   for 11b/g/n (upto 300 Mbps):  MT7620A built-in WMAC
   for 11a/n/ac (upto 867 Mbps): MT7662E
- Ethernet LAN: 1 port, upto 100 Mbps
- Ethernet WAN: 1 port, upto 1000 Mbps
- USB: 1 port (USB 2.0 host)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 1 (Displayed as "WPS" on enclosure)
- serial port: 57600n8
 pins: Vcc(3.3V), Rx, Tx, GND
(left to right, viewed from outside of board)

Installation (only available via UART):
  1. download sysupgrade binary image by wget command
  2. write sysupgrade binary image to Flash
     command is:
       mtd write sysupgrade.bin firmware
  3. reboot

Important Notice:
  Only one button is displayed as "WPS" on enclosure.
  However, it is configured as "reset" (factory resetting feature).

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[removed unrelated openwrt-keyring revert, missing -Wall for uimage_padhdr]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-26 08:09:16 +02:00
Adrian Schmutzler
f14a5c3f2f ramips: use kiB instead of B for IMAGE_SIZE
This cosmetical patch is just meant to make comparing/checking
IMAGE_SIZE values easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:34 +02:00
Adrian Schmutzler
9d87a58d34 ramips: remove ralink_default_fw_size_xxx variables
There are frequent examples of the ralink_default_fw_size_xxx
variables being used to "roughly" set flash size without caring
about the actual size of the firmware partition.

To discourage this behavior, this patch removes the variables and
just sets IMAGE_SIZE by its numeric value for each target.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:30 +02:00
Adrian Schmutzler
363197311b ramips: remove default IMAGE_SIZE for ramips target
Currently, ramips target defines 0x7b0000 as default IMAGE_SIZE
for all devices in ramips target, i.e. this will be set if a
device does not specify IMAGE_SIZE itself.

From 92 devices using that default due to a "missing" IMAGE_SIZE,
14 were incorrect by a small amount (i.e. still "8M" flash) and
12 were completely off ("16M", "4M", ...).

This patch thus removes the _default_ IMAGE_SIZE and defines
IMAGE_SIZE for each device individually. This should indicate to
people supporting new devices that this parameter has to be cared
about.

For the present code, this patch is cosmetical.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:27 +02:00
Adrian Schmutzler
24ded1810b ramips/rt305x: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                       *.MK    *.DTS     VERDICT
7links_px-4885-4m            (4M)    0x3b0000
7links_px-4885-8m            -       0x7b0000  default
8devices_carambola           -       0x7b0000  default
accton_wr6202                -       0x7b0000  default
airlive_air3gii              (4M)    0x3b0000
alfa-network_w502u           -       0x7b0000  default
allnet_all0256n-4m           (4M)    0x3b0000
allnet_all0256n-8m           -       0x7b0000  default
allnet_all5002               32448k  0x1fb0000
allnet_all5003               32448k  0x1fb0000
alphanetworks_asl26555-16m   15872k  0xf80000
alphanetworks_asl26555-8m    7744k   0x790000
arcwireless_freestation5     -       0x7b0000  default
argus_atp-52b                7808k   0x7a0000
asiarf_awapn2403             (4M)    0x3b0000
asiarf_awm002-evb-4m         (4M)    0x3b0000
asiarf_awm002-evb-8m         -       0x7b0000  default
asus_rt-g32-b1               (4M)    0x3b0000
asus_rt-n10-plus             (4M)    0x3b0000
asus_rt-n13u                 -       0x7b0000  default
asus_wl-330n                 (4M)    0x3b0000
asus_wl-330n3g               (4M)    0x3b0000
aximcom_mr-102n              -       0x790000  wrong
aztech_hw550-3g              -       0x7b0000  default
belkin_f5d8235-v2            7744k   0x790000
belkin_f7c027                7616k   0x770000
buffalo_whr-g300n            3801088 0x3a0000
dlink_dap-1350               7488k   0x750000
dlink_dcs-930                (4M)    0x3b0000
dlink_dcs-930l-b1            (4M)    0x3b0000
dlink_dir-300-b1             (4M)    0x3b0000
dlink_dir-300-b7             (4M)    0x7b0000  wrong
dlink_dir-320-b1             -       0x7b0000  default
dlink_dir-600-b1             (4M)    0x3b0000
dlink_dir-610-a1             (4M)    0x3b0000
dlink_dir-615-d              (4M)    0x3b0000
dlink_dir-615-h1             (4M)    0x3b0000
dlink_dir-620-a1             -       0x7b0000  default
dlink_dir-620-d1             -       0x7b0000  default
dlink_dwr-512-b              7800k   0x7e0000  wrong
easyacc_wizard-8800          -       0x7b0000  default
edimax_3g-6200n              3648k   0x390000
edimax_3g-6200nl             3648k   0x390000
engenius_esr-9753            (4M)    0x3b0000
fon_fonera-20n               -       0x7b0000  default
hame_mpr-a1                  (4M)    0x3b0000
hame_mpr-a2                  -       0x7b0000  default
hauppauge_broadway           7744k   0x790000
hilink_hlk-rm04              -       0x3b0000  wrong
hootoo_ht-tm02               -       0x7b0000  default
huawei_d105                  (4M)    0x3b0000
huawei_hg255d                15744k  0xf60000
intenso_memory2move          -       0x7b0000  default
jcg_jhr-n805r                (4M)    0x3b0000
jcg_jhr-n825r                (4M)    0x3b0000
jcg_jhr-n926r                (4M)    0x3b0000
mofinetwork_mofi3500-3gn     -       0x7b0000  default
netcore_nw718                3712k   0x3a0000
netgear_wnce2001             (4M)    0x350000  wrong
nexaira_bc2                  -       0x7b0000  default
nexx_wt1520-4m               (4M)    0x3b0000
nexx_wt1520-8m               -       0x7b0000  default
nixcore_x1-16m               16064k  0xfb0000
nixcore_x1-8m                7872k   0x7b0000
olimex_rt5350f-olinuxino     -       0x7b0000  default
olimex_rt5350f-olinuxino-evb -       0x7b0000  default
omnima_miniembplug           -       0x7b0000  default
omnima_miniembwifi           -       0x7b0000  default
petatel_psr-680w             (4M)    0x3b0000
planex_mzk-dp150n            (4M)    0x3b0000
planex_mzk-w300nh2           3648k   0x390000
planex_mzk-wdpr              -       0x680000  wrong
poray_ip2202                 -       0x7b0000  default
poray_m3                     (4M)    0x3b0000
poray_m4-4m                  (4M)    0x3b0000
poray_m4-8m                  -       0x7b0000  default
poray_x5                     -       0x7b0000  default
poray_x8                     -       0x7b0000  default
prolink_pwh2004              -       0x7b0000  default
ralink_v22rw-2x2             (4M)    0x3b0000
sitecom_wl-351               (4M)    0x3b0000
skyline_sl-r7205             (4M)    0x3b0000
sparklan_wcr-150gn           (4M)    0x3b0000
teltonika_rut5xx             -       0xfb0000  wrong
tenda_3g150b                 (4M)    0x3b0000
tenda_3g300m                 (4M)    0x3b0000
tenda_w150m                  (4M)    0x3b0000
tenda_w306r-v2               (4M)    0x3b0000
trendnet_tew-638apb-v2       (4M)    0x3b0000
trendnet_tew-714tru          -       0x7b0000  default
unbranded_a5-v11             (4M)    0x3b0000
unbranded_wr512-3gn-4m       (4M)    0x3b0000
unbranded_wr512-3gn-8m       -       0x7b0000  default
unbranded_xdx-rn502j         (4M)    0x3b0000
upvel_ur-326n4g              (4M)    0x3b0000
upvel_ur-336un               -       0x7b0000  default
vocore_vocore-16m            16064k  0xfb0000
vocore_vocore-8m             7872k   0x7b0000
wansview_ncs601w             -       0x7b0000  default
wiznet_wizfi630a             (16M)   0xfb0000
zorlik_zl5900v2              -       0x7b0000  default
zyxel_keenetic               (4M)    0x3b0000
zyxel_keenetic-start         (4M)    0x3b0000
zyxel_nbg-419n               (4M)    0x3b0000
zyxel_nbg-419n-v2            (8M)    0x7b0000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:23 +02:00
Adrian Schmutzler
1c611f1617 ramips/rt288x,rt3883: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                 *.MK    *.DTS      VERDICT
airlink101_ar670w      (4M)    0x3c0000   wrong
airlink101_ar725w      -       0x3B0000   wrong
asus_rt-n15            (4M)    0x3b0000
belkin_f5d8235-v1      7744k   0x7b0000   wrong
buffalo_wli-tx4-ag300n (4M)    0x3b0000
buffalo_wzr-agl300nh   (4M)    0x3b0000
dlink_dap-1522-a1      3801088 0x3a0000
ralink_v11st-fe        (4M)    0x003b0000

asus_rt-n56u           -       0x007b0000 default
belkin_f9k1109v1       7224k   0x7a0000   wrong
dlink_dir-645          -       0x7b0000   default
edimax_br-6475nd       7744k   0x00790000
loewe_wmdr-143n        -       0x7b0000   default
omnima_hpm             16064k  0x00fb0000
samsung_cy-swr1100     -       0x7b0000   default
sitecom_wlr-6000       7244k   0x713000
trendnet_tew-691gr     -       0x007b0000 default
trendnet_tew-692gr     -       0x007b0000 default

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:18 +02:00
Adrian Schmutzler
439435f59b ramips/mt76x8: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                       *.MK   *.DTS     VERDICT
alfa-network_awusfree1       (8M)   0x7b0000
buffalo_wcr-1166ds           -      0x7c0000  wrong
cudy_wr1000                  (8M)   0x7b0000
d-team_pbr-d1                (16M)  0x0fb0000
duzun_dm06                   -      0x7b0000  default
glinet_gl-mt300n-v2          16064k 0xfb0000
glinet_vixmini               7872k  0x7b0000
hilink_hlk-7628n             (32M)  0x1fb0000
hiwifi_hc5661a               (16M)  0xf70000  wrong
hiwifi_hc5861b               15808k 0xf70000
mediatek_linkit-smart-7688   (32M)  0x1fb0000
mediatek_mt7628an-eval-board (4M)   0x7b0000  wrong
mercury_mac1200r-v2          -      0x7c0000  wrong
netgear_r6120                15744k 0xf60000
onion_omega2                 (16M)  0xfb0000
onion_omega2p                (32M)  0x1fb0000
rakwireless_rak633           -      0x7b0000  default
skylab_skw92a                16064k 0xfb0000
tama_w06                     15040k 0xeb0000
totolink_lr1200              7872k  0x7b0000
tplink_archer-c20-v4         7808k  0x7a0000
tplink_archer-c50-v3         7808k  0x7a0000
tplink_archer-c50-v4         7616k  0x770000
tplink_tl-mr3020-v3          7808k  0x7a0000
tplink_tl-mr3420-v5          7808k  0x7a0000
tplink_tl-wa801nd-v5         7808k  0x7a0000
tplink_tl-wr802n-v4          7808k  0x7a0000
tplink_tl-wr840n-v4          7808k  0x7a0000
tplink_tl-wr840n-v5          3904k  0x3d0000
tplink_tl-wr841n-v13         7808k  0x7a0000
tplink_tl-wr841n-v14         3968k  0x3e0000
tplink_tl-wr842n-v5          7808k  0x7a0000
tplink_tl-wr902ac-v3         7808k  0x7a0000
unielec_u7628-01-128m-16m    16064k 0xfb0000
vocore_vocore2               (16M)  0xfb0000
vocore_vocore2-lite          (16M)  0x7b0000  wrong
wavlink_wl-wn570ha1          (8M)   0x7b0000
wavlink_wl-wn575a3           (8M)   0x7b0000
widora_neo-16m               (16M)  0x0fb0000
widora_neo-32m               (32M)  0x1fb0000
wiznet_wizfi630s             (32M)  0x1fb0000
wrtnode_wrtnode2p            (16M)  0x1fb0000 wrong
wrtnode_wrtnode2r            (16M)  0x1fb0000 wrong
xiaomi_mir4a-100m            14976k 0xea0000
xiaomi_miwifi-nano           (16M)  0xfb0000
zbtlink_zbt-we1226           (8M)   0x7b0000
zyxel_keenetic-extra-ii      14912k 0xe90000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:15 +02:00
Adrian Schmutzler
7263838e69 ramips/mt7621: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                     *.MK     *.DTS     VERDICT
afoundry_ew1200            (16M)    0xfb0000
asiarf_ap7621-001          (16M)    0xfa0000  wrong
buffalo_wsr-1166dhp        (16M)    0xf90000  wrong
buffalo_wsr-600dhp         (16M)    0xfb0000
dlink_dir-860l-b1          (16M)    0xfb0000
d-team_newifi-d2           (32M)    0x1fb0000
d-team_pbr-m1              (16M)    0xfb0000
elecom_wrc-1167ghbk2-s     15488k   0xf20000
elecom_wrc-1900gst         11264k   0xb00000
elecom_wrc-2533gst         11264k   0xb00000
firefly_firewrt            (16M)    0xfb0000
gehua_ghl-r-001            (32M)    0x1fb0000
gnubee_gb-pc1              (32M)    0x1fb0000
gnubee_gb-pc2              (32M)    0x1fb0000
hiwifi_hc5962              (32M)    0x2000000 wrong (kernel + ubi)
iodata_wn-ax1167gr         15552k   0xf30000
iodata_wn-gx300gr          7798784  0x770000
lenovo_newifi-d1           (32M)    0x1fb0000
linksys_re6500             -        0x7b0000  default
mediatek_ap-mt7621a-v60    (8M)     0x7b0000
mediatek_mt7621-eval-board (4M)     0xec0000  wrong (rootfs)
mikrotik_rb750gr3          [16128k] 0xfc0000
mikrotik_rbm11g            [16128k] 0xFC0000
mikrotik_rbm33g            [16128k] 0xFC0000
mqmaker_witi-256m          (16M)    0xfb0000
mqmaker_witi-512m          (16M)    0xfb0000
mtc_wr1201                 16000k   0xfa0000
netgear_ex6150             14848k   0xe80000
netgear_r6220              28672k   0x1c00000
netgear_r6350              40960k   0x2800000
netgear_wndr3700-v5        15232k   0xee0000
netis_wf-2881              129280k  0x7E40000
phicomm_k2p                15744k   0xf60000
planex_vr500               66453504 0x3fb0000 wrong
samknows_whitebox-v8       (16M)    0xfb0000
storylink_sap-g3200u3      -        0x7b0000  default
telco-electronics_x1       16064k   0xfb0000
thunder_timecloud          -        0xfb0000  wrong
totolink_a7000r            16064k   0xfb0000
tplink_re350-v1            6016k    0x5e0000
ubiquiti_edgerouterx       -        0xfa00000 wrong (kernel1 + ubi)
ubiquiti_edgerouterx-sfp   -        0xfa00000 wrong (kernel1 + ubi)
unielec_u7621-06-256m-16m  16064k   0xfb0000
unielec_u7621-06-512m-64m  65216k   0x3fb0000
wevo_11acnas               (16M)    0xfb0000
wevo_w2914ns-v2            (16M)    0xfb0000
xiaomi_mir3g               32768k   0x7980000 wrong (kernel + ubi)
xiaomi_mir3p               (32M)    0xf980000 wrong (kernel + ubi)
xzwifi_creativebox-v1      (32M)    0x1fb0000
youhua_wr1200js            16064k   0xfb0000
youku_yk-l2                (16M)    0xfb0000
zbtlink_zbt-we1326         (16M)    0xfb0000
zbtlink_zbt-we3526         (16M)    0xfb0000
zbtlink_zbt-wg2626         (16M)    0xfb0000
zbtlink_zbt-wg3526-16m     (16M)    0xfb0000
zbtlink_zbt-wg3526-32m     (32M)    0x1fb0000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:11 +02:00
Adrian Schmutzler
7009f407f1 ramips/mt7620: fix IMAGE_SIZE for all devices
This fixes IMAGE_SIZE for all devices based on the partition size
given in DTS:

DEVICE                     *.MK     *.DTS      VERDICT
aigale_ai-br100            7936k    0x7c0000
alfa-network_ac1200rm      16064k   0xfb0000
alfa-network_tube-e4g      16064k   0xfb0000
asus_rp-n53                -        0x7b0000   default
asus_rt-ac51u              (16M)    0xfb0000
asus_rt-n12p               -        0xfb0000   wrong
asus_rt-n14u               -        0xfb0000   wrong
bdcom_wap2100-sk           15808k   0xf70000
buffalo_whr-1166d          15040k   0xfb0000   wrong
buffalo_whr-300hp2         6848k    0x7b0000   wrong
buffalo_whr-600d           6848k    0x7b0000   wrong
buffalo_wmr-300            -        0x7b0000   default
comfast_cf-wr800n          -        0x7b0000   default
dlink_dch-m225             6848k    0x6b0000
dlink_dir-510l             -        0xde0000   wrong
dlink_dir-810l             6720k    0x690000
dlink_dwr-116-a1           -        0x7e0000   wrong
dlink_dwr-118-a1           -        0xfe0000   wrong
dlink_dwr-118-a2           -        0xfe0000   wrong
dlink_dwr-921-c1           (16M)    0xfe0000   wrong
dlink_dwr-921-c3           [(16M)]  0xfe0000   wrong
dlink_dwr-922-e2           (16M)    0xfe0000   wrong
dovado_tiny-ac             -        0x7b0000   default
edimax_br-6478ac-v2        7616k    0x00790000 wrong
edimax_ew-7476rpc          7744k    0x00790000
edimax_ew-7478ac           7744k    0x00790000
edimax_ew-7478apc          7744k    0x00790000
elecom_wrh-300cr           (16M)    0xdf0000   wrong
glinet_gl-mt300a           (16M)    0xf80000   wrong
glinet_gl-mt300n           (16M)    0xf80000   wrong
glinet_gl-mt750            (16M)    0xf80000   wrong
head-weblink_hdrm200       16064k   0xfb0000
hiwifi_hc5661              15872k   0xf80000
hiwifi_hc5761              15872k   0xf80000
hiwifi_hc5861              15872k   0xf80000
hnet_c108                  16777216 0xfb0000   wrong
iodata_wn-ac1167gr         6864k    0x6b4000
iodata_wn-ac733gr3         6992k    0x6d4000
kimax_u25awf-h1            16064k   0xfb0000
kimax_u35wf                16064k   0xfb0000
kingston_mlw221            15744k   0xf60000
kingston_mlwg2             15744k   0xf60000
lava_lr-25g001             -        0xfe0000   wrong
lenovo_newifi-y1           (16M)    0xfb0000
lenovo_newifi-y1s          (16M)    0xfb0000
linksys_e1700              -        0x7b0000   default
microduino_microwrt        16128k   0xfc0000
netgear_ex2700             (4M)     0x3b0000
netgear_ex3700             7744k    0x790000
netgear_wn3000rp-v3        -        0x7b0000   default
nexx_wt3020-4m             (4M)     0x3b0000
nexx_wt3020-8m             -        0x7b0000   default
ohyeah_oy-0001             (16M)    0xfb0000
phicomm_k2g                7552k    0x760000
phicomm_psg1208            -        0x7b0000   default
phicomm_psg1218a           -        0x7b0000   default
phicomm_psg1218b           -        0x7b0000   default
planex_cs-qr10             -        0x7b0000   default
planex_db-wrt01            -        0x7b0000   default
planex_mzk-750dhp          -        0x7b0000   default
planex_mzk-ex300np         -        0x730000   wrong
planex_mzk-ex750np         -        0x730000   wrong
ralink_mt7620a-evb         -        0x7b0000   default
ralink_mt7620a-mt7530-evb  -        0x7b0000   default
ralink_mt7620a-mt7610e-evb -        0x7b0000   default
ralink_mt7620a-v22sg-evb   -        0x7f80000  wrong
ravpower_wd03              (8M)     0x7b0000
sanlinking_d240            (16M)    0xfb0000
sercomm_na930              20m      0x1400000
tplink_archer-c20i         -        0x7a0000   wrong
tplink_archer-c20-v1       -        0x7a0000   wrong
tplink_archer-c2-v1        -        0x7a0000   wrong
tplink_archer-c50-v1       -        0x7a0000   wrong
tplink_archer-mr200        -        0x7b0000   default
vonets_var11n-300          (4M)     0x3b0000
wrtnode_wrtnode            (16M)    0xfb0000
xiaomi_miwifi-mini         (16M)    0xf80000   wrong
youku_yk1                  (32M)    0x1fb0000
yukai_bocco                -        0x7b0000   default
zbtlink_we1026-5g-16m      16777216 0xfb0000   wrong
zbtlink_zbt-ape522ii       -        0xf80000   wrong
zbtlink_zbt-cpe102         -        0x760000   wrong
zbtlink_zbt-wa05           -        0x760000   wrong
zbtlink_zbt-we2026         -        0x760000   wrong
zbtlink_zbt-we826-16m      (16M)    0xfb0000
zbtlink_zbt-we826-32m      (32M)    0x1fb0000
zbtlink_zbt-we826-e        32448k   0x1fb0000
zbtlink_zbt-wr8305rt       -        0x7b0000   default
zte_q7                     -        0x7b0000   default
zyxel_keenetic-omni        -        0x7b0000   default
zyxel_keenetic-omni-ii     -        0x7b0000   default
zyxel_keenetic-viva        16064k   0xfb0000

No verdict means that the device is correctly set.

Legend:
( ): Value is set via ralink_default_fw_size_xxM
[ ]: Value is derived from parent definition
 - : Value is not set and derived from default definition

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:08 +02:00
Adrian Schmutzler
a6cd311b0b ramips: support IMAGE_SIZE in kiB for Build/trx
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:05 +02:00
Adrian Schmutzler
7392af7520 ramips: fix ralink_default_fw_size_16M
In ramips, there are the following predefined values for IMAGE_SIZE
ralink_default_fw_size_4M    3866624   3776k   0x3B0000
ralink_default_fw_size_8M    8060928   7872k   0x7B0000
ralink_default_fw_size_16M  16121856  15744k   0xF60000
ralink_default_fw_size_32M  33226752  32448k  0x1FB0000

Out of those, the "16M" value is obviously odd, as it provides more
room for the remaining partitions than the tree others.
Of the devices in all subtargets, there are actually > 50 that have
a firmware partition with 0xFB0000 size, while only 5 (!) have
0xF60000. From the former, many are set to
ralink_default_fw_size_16M anyway, although it is wrong at the
present point.

Consequently, it makes sense to change ralink_default_fw_size_16M
to 0xFB0000, and to update IMAGE_SIZE for the 5 devices with
0xF60000.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-25 14:31:01 +02:00
Roger Pueyo Centelles
7d684b7673 ramips: add kmod-mt7615e to Phicomm K2P images
Now that the mt76 driver supports the MT7615D chip found on these
devices, use it.

Also add the wpad-basic package.

Note: the driver supports operation on both the 2.4 GHz and the
      5 GHz bands, but not yet concurrently.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-07-25 18:24:50 +08:00
DENG Qingfang
0e6d97f961 ramips: enable Newifi D1 SD slot
Newifi D1 is shipped with an 8GB microSD card in its SD slot
Without SD driver users would not be able to use it unless manually installed

Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-07-23 13:14:07 +08:00
Georgi Vlaev
8c51ddeff0 ramips: add support for TP-Link RE650 v1
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.

Hardware specification:

- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
  Serial console @ 57600,8n1

Flash instructions:

Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.

TFTP recovery to stock firmware:

Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.

Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-17 23:14:23 +02:00
INAGAKI Hiroshi
cda123fe69 ramips: add MT7615 wireless support for ELECOM WRC-1167GHBK2-S
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.

A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f35,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.

Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-17 14:45:18 +02:00
David Bauer
14e0e4f138 ramips: add support for ASUS RT-AC57U
SoC:   MediaTek MT7621AT
RAM:   128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi:  MediaTek MT7603EN bgn 2SS
WiFi:  MediaTek MT7612EN nac 2SS
BTN:   Reset - WPS
LED:    - Power
        - LAN {1-4}
        - WAN
        - WiFi 2.4 GHz
        - WiFi 5 GHz
        - USB
UART:  UART is present next to the Power LED.
       TX - RX - GND - 3V3 / 57600-8N1
       3V3 is the nearest one to the Power LED.

Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
 > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>

Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
 > scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
 > ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
 > mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
 > reboot

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-11 21:32:39 +02:00
Chuanhong Guo
087e14ab59 ramips: mt7621: merge two variants of MQmaker WiTi together
Since we can auto-detect memory now, we don't need 2 dts for two
memory variants.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-11 22:11:21 +08:00
Daniel Golle
98d04dc4cf ramips: fix bogus MTK_SOC (typo)
Belkin F7C027 is clearly Rt5350 SoC, as shown on internal
photographs filed for FCC approval[1].

[1]: https://fcc.io/K7S/F7C027

Fixes commit 3b0264eddb
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-10 19:28:35 +02:00
Adrian Schmutzler
447deed52a ramips: Sort all subtarget Makefiles
This patch applies sorting to the definitions as whole blocks.

Sorting has been performed fully automatic, line count differences
originate from double empty lines removed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
3b0264eddb ramips/rt305x: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
6a104ac772 ramips/rt288x,rt3883: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
b97a99256f ramips/mt76x8: Name DTS files based on scheme
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
7196ca1d49 ramips/mt7621: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
48047b3a5c ramips/mt7620: Name DTS files based on scheme
As introduced with ath79, DTS files for ramips will now be labelled
soc_vendor_device.dts(i). With this change, DTS files can be
selected automatically without further manual links.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
402138d12d ramips: Derive DTS name from device name in Makefile
This will automatically derive the DTS name as in ath79 and thus
makes specifying DTS for every device obsolete.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>

---

This patch only introduces the mechanism and is then followed by
commits with renames and Makefile adjustments per subtarget.

Eventually, those can be all squashed into a single commit or left
as they are to enhance overview.
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
7dd3a234be ramips/rt305x: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
83efa8329b ramips/rt288x,rt3883: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
c2334ad60d ramips/mt76x8: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
2f2a319f82 ramips/mt7621: Synchronize Makefiles with DTS compatible
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
9f99000165 ramips/mt7620: Synchronize Makefiles with DTS compatible
This will "rename" devices in Makefiles to the pattern used in
DTS compatible. This will systematize naming of devices
enormously.

As device names are used to for default SUPPORTED_DEVICES entries,
we need to adjust the source for /tmp/sysinfo/board_name, too.
So remove relevant entries from base-files/lib/ramips.sh and
use device compatible for that.

Despite that, base-files are updated, too.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:29 +02:00
Adrian Schmutzler
d93969a13a ramips: Improve compatible for TP-Link Archer devices
Include "Archer" in compatible as it is part of the device name.

Update Makefile device names where necessary to match compatible.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-10 17:36:28 +02:00
Daniel Golle
c2b1baf767 ramips: add missing DEVICE_VENDOR
Fixes commit ee66fe4ea9
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-10 17:15:49 +02:00
Chuanhong Guo
7a8d3432c7 ramips: use upstream RAW_APPENDED_DTB instead of our OWRTDTB
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")

Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-07-08 22:00:24 +02:00
Daniel Golle
ee66fe4ea9 ramips: convert DEVICE_TITLE to new variables
Also unify naming and add details where they were missing.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-07-06 14:58:03 +02:00
Alexander Müller
3fd97c522b
ramips: add support for TP-Link TL-WR841n v14
TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N.

- MediaTek MT7628NN
- 32 MB of RAM
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet

Installation:
- copy the
  'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin'
  file to your tftp server root and rename it to 'tp_recovery.bin'.
- configure your PC running the TFTP server with the static IP address
  192.168.0.66/24
- push the reset button and plug in the power connector. Wait until
  the orange led starts blinking (~6sec)

Signed-off-by: Alexander Müller <donothingloop@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
2019-07-02 16:17:49 +02:00
Chuanhong Guo
3f68cffd27 ramips: add support for TOTOLINK A7000R
Specifications:
- SoC: MT7621AT
- RAM: 128MB
- Flash: 16M SPI NOR
- Ethernet: 5x GE ports
- WiFi: 2.4G: MT7615N
        5G: MT7615N

Flash instruction:
Upload generated sysupgrade firmware through factory web interface.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-26 07:41:54 +02:00
Daniel Danzberger
029c970464 ramips: mt7621: Add new device AsiaRF AP7621-001
Hardware specs:
SoC:	Mediatek MT7621A
CPU:	4x 880Mhz
Cache:	32 KB I-Cache and 32 KB D-Cach
	256 KB L2 Cache (shared by Dual-Core)
RAM:	DDR3 512MB 16bits BUS
FLASH:	16MB
Switch:	Mediatek Gigabit Switch (1 x LAN, 1 x WAN)
USB:	1x 3.0
PCI:	3x Mini PCIe
GPS:	Quectel L70B
BTN:	Reset
LED:	- Power
	- Ethernet
	- Wifi
	- USB
UART:	UART is present as Pads with throughholes on the PCB.
	They are located on left side.
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation:
The stock image is a modified openwrt and can be overflashed via
 # sysupgrade -F image.bin

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed unused label, formatting]
2019-06-25 15:02:21 +02:00
Birger Koblitz
ab7f8146fd ramips: add support for Edimax EW-7478APC
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB:	Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN:	Reset/WPS
LED:    - Power (white)
	- Internet (blue)
	- Wifi (blue)
	- USB (blue)
UART:  UART is present as Pads with throughholes on the PCB. They are
       located in the lower right corner (GbE ports facing up)
       3.3V - RX - GND - TX / 57600-8N1
       3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:48:19 +02:00
Birger Koblitz
88f7a29f99 ramips: add support for Edimax EW-7476RPC / EW-7478AC
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS - RFKILL/RF 50%/RF 100% toggle
LED:	- Wifi 5g (blue)
	- Wifi 2g (blue)
	- Crossband (green)
	- Power (green)
	- WPS (green)
	- LAN (Green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the switch for the wifi configuration
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp

ramips: add Edimax EW-7478AC

SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS - RFKILL/RF 50%/RF 100% toggle
LED:	- Wifi 5g (blue)
	- Wifi 2g (blue)
	- Crossband (green)
	- Power (green)
	- WPS (green)
	- LAN (Green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the switch for the wifi configuration
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6

The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-06-20 08:31:24 +02:00
Deng Qingfang
b47cf6d539 ramips: mt7620: select kmod-rt2800-pci driver for RT5592
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages

Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-06-10 11:25:47 +02:00
Chuanhong Guo
0ab9f283f7 ramips: add support for TOTOLINK LR1200
Specifications:
- SoC: MT7628DAN (MT7628AN with 64MB built-in RAM)
- Flash: 8M SPI NOR
- Ethernet: 5x 10/100Mbps
- WiFi: 2.4G: MT7628 built-in
        5G: MT7612E
- 1x miniPCIe slot for LTE modem (only USB pins connected)
- 1x SIM slot

Flash instruction:
U-boot has a builtin web recovery page:
1. Hold the reset button while powering it up
2. Connect to the ethernet and set an IP in 192.168.1.0/24 range
3. Open your browser and upload firmware through http://192.168.1.1

Note about the LTE modem:
If your router comes with an EC25 module and it doesn't show up
as a QMI device, you should do the following to switch it to QMI
mode:
1. Install kmod-usb-serial-option and a terminal software
   (e.g. minicom or screen). All 4 serial ports of the modem
   should be available now.
2. Open /dev/ttyUSB3 with the terminal software and type this
   AT command: AT+QCFG="usbnet",0
3. Power-cycle the router. You should now get a QMI device
   recognized.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-06-05 10:26:33 +02:00
Jan Hoffmann
085f66de9a ramips: create R6220 dtsi and improve WNDR3700v5 support
The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and
having a different casing. This adds a new cleaned up R6220.dtsi with the
common bits for both devices. Both devices now have feature parity.

Performed cleanup:
 * generic DTS node names
 * regulator for usb power
 * added missing pinctrl groups
 * use switch port instead of VLAN as trigger for WAN LED

Fixes for WNDR3700v5:
 * all LEDS work
 * correct ethernet MAC addresses

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-31 11:21:22 +02:00
Markus Scheck
5ff5c9bce6 ramips: add support for Xiaomi Mi Router 4A (100M Edition)
- SoC:      MediaTek MT7628AN
- Flash:    16MB (Winbond W25Q128JV)
- RAM:      64MB
- Serial:   As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0:    MT7628AN 2.4GHz 802.11b/g/n
- WIFI1:    MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs:     Programmable power-LED (two-colored, yellow/blue)
            Non-programmable internet-LED (shows WAN-activity)
- Buttons:  Reset

INSTALLATION:

1. Connect to the serial port of the router and power it up.
   If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
       > Erasing SPI Flash...
       > raspi_erase: offs:20000 len:10000
   occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
   write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
   Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.

Signed-off-by: Markus Scheck <markus@mscheck.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added mt76 compatible]
2019-05-31 11:21:22 +02:00
Davide Fioravanti
7c91144ae6 ramips: add CUDY WR1000 support
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas

Specifications:

MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button

Known issues:
The Power LED is always ON, probably because it is connected
directly to power.

Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.

Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.

Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
  WR1000_EU_92.122.2.4987.201806261618.bin
  WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.

1) Download the original FW from the Cudy website.

   (For example WR1000_EU_92.122.2.4987.201806261618.bin)

2) Remove the header.

   dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64

3) XOR the new file with the region key.

   FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
   FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C

   You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:

   xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..

   Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
   https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)

4) Check the resulting decrypted image.

   Check if bytes from 0x20 to 0x3f are:
   4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00

   Alternatively, you can use u-boot's tool dumpimage tool to check
   if the decryption was successful. It should look like:

   # dumpimage -l stock-firmware.bin
   Image Name:   Linux Kernel Image
   Created:      Tue Jun 26 10:24:54 2018
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    4406635 Bytes = 4303.35 KiB = 4.20 MiB
   Load Address: 80000000
   Entry Point:  8000c150

5) Flash it via forced firmware upgrade and don't "Keep Settings"

   CLI: sysupgrade -F -n stock-firmware.bin

   LuCI: make sure to click on the "Keep settings" checkbox
         to disable it. You'll need to do this !TWICE! because
         on the first try, LuCI will refuse the image and reset
	 the "Keep settings" to enable. However a new
         "Force upgrade" checkbox will appear as well.
         Make sure to do this very carefully!

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
2019-05-31 10:36:36 +02:00
Davide Fioravanti
62ce6d58f2 ramips: unify JCG helper command definition
This patch makes the JCG helper command definition available
for every rampis target

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2019-05-31 10:30:03 +02:00
Nicholas Smith
73e0f52b6e ramips: add support for Telco Electronics X1
Hardware:
SoC:   MT7621
DRAM:  256MB DDR3
Flash: 16MB SPI-NOR
WiFi:  2.4GHz: MT7603 @ PCIe0
WiFi:  5.8GHz: MT7612 @ PCIe1
Modem: Sierra Wireless MC74xx

Interfaces:
GBE RJ45 x5
mPCIe    x2
UART     x1
I2C      x1
JTAG     x1
UIM      x1
LEDs     x6

Flash instructions:
Flash from within the factory bootloader, firmware web interface or CLI using
sysupgrade -F -n

Signed-off-by: Nicholas Smith <mips171@icloud.com>
2019-05-18 17:59:49 +02:00
Jan Hoffmann
2fdd02cc7c ramips: add factory image for WNDR3700v5
This uses the existing rules for Sercomm factory images and moves them
to the ramips image Makefile, so they can be used in all subtargets.

The new factory image for WNDR3700v5 can be flashed using nmrpflash.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2019-05-18 16:44:41 +02:00
Liu Yu
671c9d16e3 ramips: add support for HILINK HLK-7628N
Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       128 MB
Flash:     32 MB
WIFI:      802.11n/g/b 20/40 MHz
Ethernet:  5 Port ethernet switch
UART:      2x

Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART0 line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
   set device and tftp server IP address and input the firmware
   file name. U-boot will then load the firmware and write it into
   the flash.
5. After firmware is started connect via ethernet at 192.168.1.1

Signed-off-by: Liu Yu <f78fk@live.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
2019-05-18 13:43:55 +02:00
Kristian Evensen
869376710d ramips: Add support for ZBT WE826-E
ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:

- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button

The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address.  Upload the firmware to start the recovery
process.

How to swap SIMs:

You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-05-17 21:41:43 +02:00
Kristian Evensen
52b59a984f ramips: Add support for Head Weblink HDRM200
Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed
specifications are:

- MT7620A (580MHz)
- 64MB RAM
- 16MB of flash (SPI NOR)
- 6x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM
SIM7100E LTE modem.
- 2x SIM slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 1x 5GHz wifi (mt7612)
- 1x reset button
- 1x WPS button
- 3x GPIO-controllable LEDs
- 1x 10 pin terminal block (RS232, RS485, 4 x GPIO)

Tested:
- Ethernet switch
- Wifi
- USB slot
- SD card slot
- miniPCIe-slot
- sysupgrade
- reset button

Installation instructions:

Installing OpenWRT for the first time requires a bit of work, as the
board does not ship with OpenWRT. In addition, the bootloader
automatically reboots when installing an image over tftp. In order to
install OpenWRT on the HDRM200, you need to do the following:

* Copy the initramfs-image to your tftp-root (default filename is
test.bin) and configure networking accordingly (default server IP is
10.10.10.3, client 10.10.10.123). Start your tftp server.
* Open the board and connect to UART. The pins are exposed and clearly
marked.
* Boot the board and press 1.
* Either use the default filename and client/server IP-addresses, or
specify your own.

The image should now be loaded to memory and board boot. If the router
reboots while the image is loading, you need to try again. Once the
board has booted, copy the sysupgrade-image to the router and run
sysupgrade in order to install OpenWRT to the flash.

Notes:

- You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio0/value. In order for the change to take
effect, you can either use AT-commands (AT+CFUN) or power-cycle the
modem (write 0/1 to /sys/class/gpio/gpio21/value).
- RS485 is available on /dev/ttyS0.
- RS232 is available on /dev/ttyS1.
- The name of the ioX-gpios map to the labels on the casing.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
[fixed whitespace issue and merge conflict in target.mk]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-05-17 21:41:43 +02:00
David Bauer
a4dc519888 ramips: fix R6120 factory image
The factory firmware omits the JFFS2 end-marker while flashing via
web-interface. Add a 64k padding after the marker fixes this problem.

When the end-marker is not present, OpenWRT won't save the overlayfs
after initial flash.

Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-05-11 16:37:11 +02:00
Eike Feldmann
9e0fb5a27f ramips: add support for Rakwireless RAK633
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.

Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       64 MB
Flash:     8 MB
WIFI:      802.11n/g/b 20/40 MHz
USB:       1x Port USB 2.0
Ethernet:  5 Port ethernet switch
UART:      2x

Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on.  Choose the option: "Load system code
then write to Flash via TFTP".  Choose the local device IP and the TFTP
server IP and the file name of the system image.  After if the
Bootloader will copy the image to the local flash.

Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845

Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-14 23:42:03 +02:00
David Bauer
43e8c37cb4 ramips: add support for GL.iNet VIXMINI
Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 18:46:40 +02:00
Zhao Yu
32689e93c4 ramips: add support for Youku YK-L2
Hardware spec:

CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0

Flashing instructions:

Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692

to get the bootloader and unlock firmware.

0. upgrade your router with the telnet firmware via the
   firmware upgrade page on the webui.

1. telnet 192.168.11.1 from your PC

2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
   it to the /tmp directory of the router.

3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader

4. turn off the power

5. Push the reset button while turning on the router and
   wait until LED start blinking (~10sec.)

6. Connect Ethernet port and goto http://192.168.1.1.

7. Upload the firmware to firmware restore page in webui.

Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
2019-04-06 19:13:49 +02:00
David Bauer
3f019bf96c ramips: add Netgear EX6150
SoC:   MediaTek MT7621
RAM:   64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi:  MediaTek MT7662E bgn 2SS
WiFi:  MediaTek MT7662E nac 2SS
BTN:   ON/OFF - Reset - WPS - AP/Extender toggle
LED:    - Arrow Right (blue)
        - Arrow Left (blue)
        - WiFi 1 (red/green)
        - WiFi 2 (red/green)
        - Power (green/amber)
        - WPS (Green)
UART:  UART is present as Pads on the backside of the PCB. They are
       located on the other side of the Ethernet port.
       3.3V - GND - TX - RX / 57600-8N1
       3.3V is the nearest one to the antenna connectors

Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).

You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash

Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Vladimir Kot
58becdb30d ramips: add support for ZyXEL Keenetic Start
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button

Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
   to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.

Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:34:00 +00:00
Tobias Welz
7c4b85ee27 ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.

SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)

Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1).  Then get the
sysupgrade image from a tftp server.

Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-29 07:33:59 +00:00
Pawel Dembicki
67fced9ba3 ramips: add support for DLINK DIR-510L
The DIR-510L Wireless Router are based on the MT7620A SoC.

Specification:

-MediaTek MT7620A (580 Mhz)
-128 MB of RAM
-16 MB of FLASH
-802.11bgn radio
-1x 10/100 Mbps Ethernet
-2x internal, non-detachable antennas
-UART (J3) header on PCB (57600 8n1)
-1x bi-color LED (GPIO-controlled), 2x button
-JBOOT bootloader

Known issues:
-Ethernet port is used as LAN
-No communication with charger IC. (uart bitbang needed)

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed whitespace issue in 10-rt2x00-eeprom]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-03-24 01:44:24 +01:00
Pawel Dembicki
1f149fcad3 firmware-utils: mkdlinkfw: add kernel image offset
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2019-03-24 01:44:24 +01:00
Ozgur Can Leonard
201d3d1a82 ramips: Xiaomi MIR3G: detect board name from DTS
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
  Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
INAGAKI Hiroshi
5c11258297 ramips: add support for I-O DATA WN-AC733GR3
I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification

- SoC		: MediaTek MT7620A
- RAM		: DDR2 64 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz
  - 2.4 GHz : MT7620A (SoC), 2T2R
  - 5 GHz   : MT7610E, 1T1R
- Ethernet	: 10/100/1000 Mbps (RTL8367RB)
- LED/key	: 4x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: Vcc, RX, GND, TX from LED side
  - 57600n8

Flash instruction using factory image:

1. Boot WN-AC733GR3 normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-03-21 00:57:20 +01:00
Ozgur Can Leonard
d009033911 ramips: add support for Xiaomi Mi Router 3 Pro
Hardware:

CPU:   MediaTek MT7621AT (2x880MHz)
RAM:   512MB DDR3
FLASH: 256MB NAND
WiFi:  2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI:  5GHz 4x4 MT7615 a/n/ac  (Needs driver, See Issues!)
USB:   1x 3.0
ETH:   1x WAN 10/100/1000 3x LAN 10/100/1000
LED:   Power/Status
BTN:   RESET
UART:  115200 8n1

Partition layout and boot:

Stock Xiaomi firmware has the MTD split into (among others)

- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)

Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.

Note uboot's tftp flash install writes the transferred
image to both kernel partitions.

Installation:

Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.

The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:

nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot

Reverting to stock:

The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.

For this we do the following:

fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot

After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.

Issues:

OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.

See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
2019-03-13 16:25:34 +01:00
Piotr Dymacz
9b6413982c ramips: add support for ALFA Network Tube-E4G
ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on
MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem.

Specification:

- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 1x detachable antenna (modem main)
- 1x internal antenna (modem div)
- 1x GPS passive antenna (optional)
- 5x LED (all driven by GPIO)
- 1x button (reset)
- UART (4-pin, 2.54 mm pitch) header on PCB

Other:

Default SIM slot is selected at an early stage by U-Boot, based on
'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2
(micro). U-Boot also resets the modem, using #PERST signal, before
starting kernel.

Flash instruction:

You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:

1. Power the device with reset button pressed, the LAN LED will start
   blinking slowly and after ~3 seconds, when it starts blinking faster,
   you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-11 22:00:26 +01:00
Kip Porterfield
f2c83532f9 ramips: add support for Belkin F9K1109v1
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
	Wireless 1: SoC-integrated : 2.4/5 GHz
	Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
	GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0

Flashing instructions:

Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
  in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
   *squashfs.sysupgrade.bin file then click APPLY

Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin

Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
2019-03-02 13:04:45 +01:00
Marcel Jost
e6f047fa36 ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n

Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED

Flash instruction:

The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 10 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Marcel Jost <majo@icutech.ch>
2019-02-28 11:26:10 +01:00
Thomas Vincent-Cross
a915ad8464 ramips: use generic board detection for Wavlink WL-WN575A3
Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices.

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
2019-02-28 11:26:10 +01:00
INAGAKI Hiroshi
f305ce5c35 ramips: add support for I-O DATA WN-AC1167GR
I-O DATA WN-AC1167GR is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7620A.

Specification:

- SoC     : MediaTek MT7620A
- RAM     : DDR2 64 MB
- Flash   : SPI-NOR 8MB
- WLAN    : 2.4/5 GHz, 2T2R
  - 2.4 GHz: MT7620A (SoC)
  - 5 GHz  : MT7612E
- Ethernet: 10/100/1000 Mbps (ext. MT7530)
- LED/key : 4x/3x (2x buttons, 1x slide-switch)
- UART    : through-hole on PCB
  - J2: TX, GND, RX, Vcc from SoC side
  - 115200n8

Flash instruction using factory image:

1. Boot WN-AC1167GR normaly
2. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-02-14 16:56:14 +01:00
Deng Qingfang
6621da55b7 ramips: enable MT7610E 5GHz radio of MT7620a_MT7610e EVB
This enables MT7610E of the EVB

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2019-02-05 19:37:30 +01:00
Ju Se Hoon
9f90074db7 ramips: add kmod-mt76x2 to WeVo 11AC NAS
The WeVo 11AC NAS has a MT7612E 802.11ac chip on the PCB.

Signed-off-by: Ju Se Hoon <joosahoon@gmail.com>
[renamed author from Albis-dev to real name, editted commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-05 19:37:30 +01:00
David Bauer
01dcd574a2 ramips: add support for Archer C50 v4
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.

CPU:   MediaTek MT7628 (580MHz)
RAM:   64M DDR2
FLASH: 8M SPI
WiFi:  2.4GHz 2x2 MT7628 b/g/n integrated
WiFI:  5GHz 2x2 MT7612 a/n/ac
ETH:   1x WAN 4x LAN
LED:   Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN:   WPS/WiFi, RESET
UART:  Near ETH ports, 115200 8n1, TP-Link pinout

Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.

Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:

TP-Link image:             tpl.bin
OpenWRT sysupgrade image:  owrt.bin

 > dd if=tpl.bin of=boot.bin bs=131584 count=1
 > cat owrt.bin >> boot.bin

Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.

Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.

Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.

The boot.bin can now be uploaded and flashed using the web-recovery.

Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)

 > dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
 > dd if=tpl.bin of=tmp.bin bs=131584 count=1
 > dd if=tmp.bin of=boot.bin bs=512 skip=1
 > cat boot.bin >> tp_recovery.bin
 > cat owrt.bin >> tp_recovery.bin

Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.

Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.

U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.

Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.

Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.

By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.

It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 21:46:32 +01:00
David Bauer
915fbd4e31 ramips: adjust Netgear R6120 model name
Adjust the model string and device title to match other Netgear routers
in the ramips target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:41:03 +01:00
Mathias Kresin
26a016731d firmware-utils: mksercommfw: overhaul image creation
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality

Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.

Use a fixed timestamp within the zip archive to make the images
reproducible.

Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.

Beside all changes, the footer still looks wrong in compare to the
netgear update image.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-15 19:11:54 +01:00
Anton Arapov
6ba58b7b02 ramips: cleanup the RB750Gr3 support
Always enable the pwr led and use the usr led for boot status indication.

Rename nodes in the dts, to match what is recommend in the devicetree
specification.

Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io
which isn't required on mt7621.

Use the BTN_0 keycode for the mode button. This board doesn't have any
wireless.

Use a more descriptive label for the reset button and the GPIO enabling
the usb vcc supply.

Use the beeper kernel module for the buzzer.

Fix the pinmux to switch only pins used as GPIOs to the GPIO function.
Add support for the PoE enable GPIO to the userspace. The PoE power
status can be read via GPIO7. Since OpenWrt doesn't have support for
reading inputs from userspace, prepare only the pinmux for the GPIO.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Anton Arapov
52f2d7d2a9 ramips: add RB750Gr3 native support
This patch adds support of MikroTik RouterBOARD 750Gr3, without the need
to reflashing the bootloader.

Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common

Since the image isn't compatible with RouterBOARD 750Gr3 installations
which have replaced the bootloader, the former used userspace boardname
is not added to the SUPPORTED_DEVICES, to prevent a brick while trying
to upgrade to the image with native support.

Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2019-01-05 12:28:22 +01:00
Mathias Kresin
fd35c5b205 build: move seama commands to image-commands.mk
Move it to image-commands.mk to get rid of duplicate recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:13 +01:00
Mathias Kresin
7c1332d95f ramips: consolidate seama image build code
Create a common template which has the required image build code
defined. Add some new variables to pass individual parts to the seama
recipes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-30 20:08:12 +01:00
Deng Qingfang
5580a9dd31 ramips: add support for GeHua GHL-R-001
Specs
	SoC: MT7621AT
	RAM: 512MiB
	Flash: 32MiB MX25L25635F SPI NOR
	2.4G: MT7603EN
	5G: MT7612EN
	Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
	USB 3.0
	LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
	      The last two ones are controlled by GPIO
	UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
	      UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
	      The stock u-boot uses UARTLITE1 by default. Baud rate is 57600

Flash instruction
	1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
	   One can alternatively use UART to log in
	2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
	   One can alternatively download the firmware via wget through Internet
	3. mtd write /path/to/openwrt.bin firmware
	4. reboot

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-29 16:03:30 +01:00
Simon Quigley
9f0e233576 ramips: add support for DLINK DWR-922-E2
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui, or via recovery interface:

How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
    LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
    one manually
3.) Upload original factory image via JBOOT http interface at IP
    192.168.123.254
4.) If http doesn't work, it can be done with curl command:
      curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
    upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
    type "reboot" into the telnet session.

Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-29 16:03:30 +01:00
Weijie Gao
74af8a833a ramips: add support for CreativeBox v1
Hardware:
SoC: MT7621
DRAM: 512MB DDR3
Flash: 32MB SPI-NOR
WiFi 2.4GHz: MT7603 @ PCIe0
WiFi 5.8GHz: MT7612 @ PCIe1
SATA: ASM1061 @ PCIe2

Interfaces:
GBE RJ45 x5
USB3.0 x1
eSATA (with USB2.0) x1
SATA x1
UART x1
I2C x1
JTAG x1

Flash instructions:
Through factory bootloader or firmware web interface

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-12-28 12:45:23 +01:00
NOGUCHI Hiroshi
83a97c53fa ramips: add support for Netgear R6350
Netgear R6350 is a wireless router, aka Netgear AC1750.

Specification:
- SoC: Mediatek MT7621AT (2 CPU cores, 4 threads)
- RAM: 128MiB (Nanya NT5CC64M16GP-DI)
- ROM: 128MiB NAND Flash (Macronix MX30LF1G18AC-TI)
- Wireless:
   for 11b/g/n (upto 300Mbps): MT7603
   for 11a/ac  (upto 1450Mbps) : MT7615, is not avaliable now
- Ethernet LAN speed: up to 1000Mbps
- Ethernet LAN ports: 4
- Ethernet WAN speed: up to 1000Mbps
- Ethernet WAN ports: 1
- USB ports: 1 (USB 2.0)
- LEDs: 4 (all can be controlled by SoC's GPIO)
- buttons: 2
- serial ports: unknown

Installation through telnet:
  - Copy kernel.bin and rootfs.bin to a USB flash disk,
    plug to usb port on the router.
  - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug
    (login if required, default: admin password)
  - You will see "Debug Enabled!"
  - Telnet 192.168.1.1 and login with "root"
  - ls /mnt/shares/ to find out path of your USB disk.
    'myUdisk' for example.
  - cd /mnt/shares/myUdisk
  - mtd_write write rootfs.bin Rootfs
  - mtd_write write kernel.bin Kernel
  - reboot

recovery when bricked:
  nmrpflash can be used to recover to the netgear firmware
  if a broken image was flashed.

The SC_PART_MAP partition suggests that an on flash partition table
exists. After implementing a partition parser/builder for the sercom
partition format, the definitions don't match the flash layout used by
the stock firmware.

It either means the partition format has not yet been completely
understood or it isn't used by the stock firmware. For now, use fixed
partitions instead.

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[apply latest ramips changes and document the on flash partition map
issues]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-16 08:41:41 +01:00
Mathias Kresin
dd5e7d6c50 ramips: mt7620: add usb packages
Add the usb drivers for all boards with enabled ochi/ehci node in the
dts file.

Fixes: FS#1987

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Mathias Kresin
30c07a5675 ramips: mt7620: remove unnecessary usb packages
These are either installed as dependency or not required at all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Mathias Kresin
e04d352d63 ramips: mt7620: add usb ohci driver
Add the USB 1.1 driver for all boards not having a fixed USB 2.0
device attached to the USB bus.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-15 20:02:07 +01:00
Deng Qingfang
47381aadd5 ramips: several fixes for HC5x61
- Mark other partitions as read-only for HC5x61

 - Only enable USB and PCIe for HC5761/HC5861
   HC5661 doesn't have a USB port, and there is nothing attached to its PCIe.

 - Fix HC5761 switch ports
   HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports.

 - Fix HC5861 5GHz radio
   HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN.

 - Fix HC5761/HC5861 WiFi LEDs
   After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1.

 - Fix HC5x61 image size
   It should be 15872k (0xf80000)

Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
2018-12-15 20:02:07 +01:00
Mathias Kresin
8e40fbff0b ramips: drop support for ALLNET ALL0239-3G and Sitecom WL-341 v3
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.

Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.

The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Mathias Kresin
262b885b83 ramips: use new image build code for D-Link DCS-930 family
Drop the factory images and the firmware tool to create them. They don't
work any more, since the factory image has an uImage header covering the
whole kernel + rootfs. This way the uImage splitter will not be able to
find the rootfs and the kernel will panic later on.

The factory images were most likely added at a time the board had
distinct partitions for kernel and rootfs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-12 11:01:59 +01:00
Chen Minqiang
295b37d207 ramips: mt76x8: select only the matching mt76 driver
Select the matching mt76 driver for the PCI wireless of the following
devices:

 - HiWiFi HC5861B
 - Mercury MAC1200R v2.0
 - Netgear AC1200 R6120
 - Buffalo WCR-1166DS
 - ZyXEL Keenetic Extra II
 - Wavlink WL-WN575A3

Because every device has selected the corresponding mt76 driver, we can
include kmod-mt7603 instead of the mt76 metapackage, which used for the
wireless of the mt7628 and mt7688 WiSoC.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[select kmod-mt7603 as target default package, add wireless driver for
WL-WN575A3]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Chuanhong Guo
5563d49a39 ramips: disable sdhc for HC5661A
Currently OpenWrt doesn't support switching MT7628 into AP mode
(which is done by writing some undocumented registers in MTK SDK)
Without doing so, enabling SD breaks 4 FE ports and the SD controller
doesn't work since SD pins aren't configured correctly.

Disable SDHC on HC5661A to recover the 4 FE ports.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[drop the sdhci node completely]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-06 12:17:25 +01:00
Mathias Kresin
f381cbcb5f ramips: fix Netgear EX3700/EX3800 wireless driver selection
Fix the typo to select kmod-mt76x2.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-04 20:40:27 +01:00
Pawel Dembicki
e9a9b7d1ed ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 3x 10/100 Mbps Ethernet (3 LAN)
- 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN)
- 1x internal, non-detachable antenna
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- WIFI 5G LED not working
- flash is very slow

The status led has been assigned to the dwr-118-a1:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang
40692f0fb5 ramips: mt7620: select only the matching mt76 driver
Because every device has selected the corresponding mt76 driver, we can
now disable the mt76 metapackage by default to make sure that other
devices (those don't need mt76) avoid selecting unwanted packages.

We can find the hardware specifies and determine the dependencies on
these sites:
  https://wikidevi.com/wiki/
  https://openwrt.org/toh/hwdata/

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Chen Minqiang
7a32a73e52 ramips: mt7620: drop mt76 driver for boards without mt76 wireless
These boards don't have a mt76 wireless at all and don't need any of the
mt76 family drivers.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2018-12-03 15:34:56 +01:00
Mathias Kresin
78ca6a5578 ramips: merge relocate compile into build recipe
Compile the loader if the relocate-kernel image recipe is used and get
rid of the legacy build code to do so.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-30 09:04:29 +01:00
Valentín Kivachuk
30a7ab8f61 ramips: add support for MTC Wireless Router WR1201
MTC Wireless Router WR1201 is the OEM name of the board. It is also sold
rebranded as STRONG Dual Band Gigabit Router 1200.

Specification:
- SoC: MediaTek MT7621A (880 MHz)
- Flash: 16 MiB
- RAM: 128 MiB
- Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN)
- Ethernet speed: 10/100/1000
- Ethernet ports: 4+1
- 1x USB 3.0
- 1x microSD reader
- Serial baud rate of Bootloader and factory firmware: 57600

The OEM webinterface writes only as much bytes as listed in the
uImage header field to the flash. Also, the OEM webinterface
evaluates the name field of uImage header before flashing (the
string "WR1201_8_128")

To flash via webinterface, is mandatory to use first initramfs.bin
and after (from the OpenWrt) the sysupgrade.bin

Some notes:
- Some microSD will not work:

  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: card claims to support voltages below defined range
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising SDIO card
  mtk-sd 1e130000.sdhci: no support for card's volts
  mmc0: error -22 whilst initialising MMC card

Signed-off-by: Valentín Kivachuk <vk18496@gmail.com>
2018-11-30 00:20:28 +01:00
Mathias Kresin
1977be8bd0 ramips: unifiy sysupgrade file extensions
Use .bin as file extension where possible. The user doesn't need to that
sysupgrade images for NAND boards are tarballs.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-29 13:15:44 +01:00