mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-23 23:42:43 +00:00
ramips: add support for D-Link DWR-118-A1
The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This commit is contained in:
Pawel Dembicki
Mathias Kresin
parent
40692f0fb5
commit
e9a9b7d1ed
@ -114,6 +114,11 @@ dlink,dwr-116-a1|\
|
||||
mzk-ex300np)
|
||||
set_wifi_led "$boardname:green:wifi"
|
||||
;;
|
||||
dlink,dwr-118-a1)
|
||||
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1f"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x20"
|
||||
set_wifi_led "$boardname:green:wlan2g" "wlan1"
|
||||
;;
|
||||
dlink,dwr-118-a2)
|
||||
ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e"
|
||||
ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01"
|
||||
|
||||
@ -162,6 +162,10 @@ ramips_setup_interfaces()
|
||||
wrh-300cr)
|
||||
ucidef_set_interface_lan "eth0"
|
||||
;;
|
||||
dlink,dwr-118-a1)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6@eth0"
|
||||
;;
|
||||
dlink,dwr-118-a2)
|
||||
ucidef_add_switch "switch0" \
|
||||
"1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0"
|
||||
@ -475,6 +479,7 @@ ramips_setup_macs()
|
||||
wan_mac=$(mtd_get_mac_ascii factory wanmac)
|
||||
;;
|
||||
dlink,dwr-116-a1|\
|
||||
dlink,dwr-118-a1|\
|
||||
dlink,dwr-118-a2|\
|
||||
dlink,dwr-921-c1|\
|
||||
lava,lr-25g001)
|
||||
|
||||
@ -55,6 +55,7 @@ case "$FIRMWARE" in
|
||||
"soc_wmac.eeprom")
|
||||
case $board in
|
||||
dlink,dwr-116-a1|\
|
||||
dlink,dwr-118-a1|\
|
||||
dlink,dwr-118-a2|\
|
||||
dlink,dwr-921-c1|\
|
||||
lava,lr-25g001)
|
||||
|
||||
@ -296,6 +296,7 @@ platform_check_image() {
|
||||
return 0
|
||||
;;
|
||||
dlink,dwr-116-a1|\
|
||||
dlink,dwr-118-a1|\
|
||||
dlink,dwr-118-a2|\
|
||||
dlink,dwr-921-c1|\
|
||||
dwr-512-b|\
|
||||
|
||||
189
target/linux/ramips/dts/DWR-118-A1.dts
Normal file
189
target/linux/ramips/dts/DWR-118-A1.dts
Normal file
@ -0,0 +1,189 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include "mt7620a.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
compatible = "dlink,dwr-118-a1", "ralink,mt7620a-soc";
|
||||
model = "D-Link DWR-118 A1";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_internet;
|
||||
led-failsafe = &led_internet;
|
||||
led-upgrade = &led_internet;
|
||||
};
|
||||
|
||||
gpio-keys-polled {
|
||||
compatible = "gpio-keys-polled";
|
||||
poll-interval = <20>;
|
||||
|
||||
wps {
|
||||
label = "wps";
|
||||
gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
|
||||
reset {
|
||||
label = "reset";
|
||||
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wan {
|
||||
label = "dwr-118-a1:green:wan";
|
||||
gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_internet: internet {
|
||||
label = "dwr-118-a1:green:internet";
|
||||
gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
lan {
|
||||
label = "dwr-118-a1:green:lan";
|
||||
gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan2g {
|
||||
label = "dwr-118-a1:green:wlan2g";
|
||||
gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
usb {
|
||||
label = "dwr-118-a1:green:usb";
|
||||
gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
|
||||
trigger-sources = <&ohci_port1>, <&ehci_port1>;
|
||||
linux,default-trigger = "usbport";
|
||||
};
|
||||
};
|
||||
|
||||
gpio_export {
|
||||
compatible = "gpio-export";
|
||||
#size-cells = <0>;
|
||||
|
||||
usb {
|
||||
gpio-export,name = "usb";
|
||||
gpio-export,output = <0>;
|
||||
gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gpio1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <80000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "jboot";
|
||||
reg = <0x0 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@10000 {
|
||||
compatible = "amit,jimage";
|
||||
label = "firmware";
|
||||
reg = <0x10000 0xfe0000>;
|
||||
};
|
||||
|
||||
config: partition@ff0000 {
|
||||
label = "config";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&ehci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ohci {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pinctrl {
|
||||
state_default: pinctrl0 {
|
||||
default {
|
||||
ralink,group = "ephy", "uartf", "spi refclk", "wled";
|
||||
ralink,function = "gpio";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie0 {
|
||||
wifi@0,0 {
|
||||
reg = <0x0000 0 0 0 0>;
|
||||
mtd-mac-address = <&config 0xe496>;
|
||||
mtd-mac-address-increment = <(2)>;
|
||||
mediatek,mtd-eeprom = <&config 0xe083>;
|
||||
};
|
||||
};
|
||||
|
||||
ðernet {
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>;
|
||||
|
||||
port@4 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy4>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
port@5 {
|
||||
status = "okay";
|
||||
phy-handle = <&phy5>;
|
||||
phy-mode = "rgmii";
|
||||
};
|
||||
|
||||
mdio-bus {
|
||||
status = "okay";
|
||||
|
||||
phy4: ethernet-phy@4 {
|
||||
reg = <4>;
|
||||
phy-mode = "rgmii-rxid";
|
||||
};
|
||||
|
||||
phy5: ethernet-phy@5 {
|
||||
reg = <5>;
|
||||
phy-mode = "rgmii-rxid";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&gsw {
|
||||
mediatek,port4 = "gmac";
|
||||
};
|
||||
@ -176,6 +176,20 @@ define Device/dlink_dwr-116-a1
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dwr-116-a1
|
||||
|
||||
define Device/dlink_dwr-118-a1
|
||||
DTS := DWR-118-A1
|
||||
DEVICE_TITLE := D-Link DWR-118 A1
|
||||
DEVICE_PACKAGES := kmod-usb2 jboot-tools kmod-mt76x0e
|
||||
DLINK_ROM_ID := DLK6E3811001
|
||||
DLINK_FAMILY_MEMBER := 0x6E38
|
||||
DLINK_FIRMWARE_SIZE := 0xFE0000
|
||||
KERNEL := $(KERNEL_DTB)
|
||||
IMAGES += factory.bin
|
||||
IMAGE/sysupgrade.bin := mkdlinkfw | pad-rootfs | append-metadata
|
||||
IMAGE/factory.bin := mkdlinkfw | pad-rootfs | mkdlinkfw-factory
|
||||
endef
|
||||
TARGET_DEVICES += dlink_dwr-118-a1
|
||||
|
||||
define Device/dlink_dwr-118-a2
|
||||
DTS := DWR-118-A2
|
||||
DEVICE_TITLE := D-Link DWR-118 A2
|
||||
|
||||
Loading…
Reference in New Issue
Block a user