Commit Graph

619 Commits

Author SHA1 Message Date
Alexandru Gagniuc
4d1fc8916c realtek: EnGenius EWS2910P: add support for SFP ports
The SFP cages 9F and 10F share the same SCL line. Currently, there
isn't a good way to model this. Thus, only one SFP port can be fully
supported.

Cage 10F is fully supported with an I2C bus and sfp handle. Linux
automatically handles enabling or disabling the TX laser.

Cage 9F is only parially supported, without the sfp handle. The SDA
line is hogged as an input, so that it remains high. SCL transitions
sould not affect modules connected to this cage. The default value of
the tx-disable line is high (active). It is exported as a gpio, but
the laser is off by default. To enable the laser:

    echo 0 > /sys/class/gpio/sff-p9-tx-disable/value

Thus, both modules can be used for networking, but only 10F will be
able to detect and identify a plugged in SFP module.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2022-06-25 15:45:30 +02:00
Alexandru Gagniuc
2cfaab4549 realtek: add support for EnGenius EWS2910P
Add support for the Engenius EWS2910P PoE switch. This is an RTL8380
based switch with two SFP slots, and PoE 802.3af one every RJ-45 port.

The specs say 802.3af, but the vendor firmware configures the PSE for
a budget of 31W, indicating 802.3at support.

Specifications:
---------------
* SoC:       Realtek RTL8380M
* Flash:     32 MiB SPI flash Macronix MX25L25635E
* RAM:       256 MiB (As reported by bootloader)
* Ethernet:  16x 10/100/1000 Mbps with PoE
              2x SFP slots
* Buttons:   1 "Reset" button on front panel
             1 "LED mode: button on front panel
             1 "On/Off" Toggle switch on the back
* Power:     48V-54V DC barrel jack
* UART:      1 serial header (JP1) with populated 2.54mm pitch header
             Labeled GRTV for ground, rx, tx, and 3.3V respectively
* PoE:       1 STM ST32F100 microcontroller
             2 BCM59111 PSE chips
Works:
------
  - (8) RJ-45 ethernet ports
  - Switch functions
  - LEDs and buttons

Not yet enabled:
----------------
  - SFP ports (will be enabled in a subsequent change)
  - Power-over-Ethernet (requires realtek-poe package)

Install via web interface:
-------------------------

The factory firmware will accept and flash the initramfs image. It is
recommended to flash to "Partition 0". Flashing to "Partition 1" is
not supported at this point.

The factory web GUI will show the following warning:

 " Warning: The firmware version is v0.00.00-c0.0.00
     The firmware image you are uploading is older than the current
     firmware of the switch. The device will reset back to default
     settings. Are you sure you want to proceed?"

This is expected when flashing OpenWrt. After the initramfs image
boots, flash the -sysupgrade using either the commandline or LuCI.

Install via serial console/tftp:
--------------------------------

The u-boot firmware will not stop the boot, regardless of which key is
pressed. To access the u-boot console, ground out the CLK (pin 16) of
the ROM (U22) when u-boot is reading the linux image. If timed
correctly, the image CRC will fail, and u-boot will drop to a shell:
    > rtk network on
    > setenv ipaddr <address of tftp server>
    > tftp $(freemem) <name-of-initramfs-image.bin>
    > bootm

Then flash the -sysupgrade using either the commandline or luci.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[gpio-led node names, OpenWrt and LuCI capitalization in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-06-25 15:43:46 +02:00
Tomasz Maciej Nowak
539e60539a generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]
This is now built-in, enable so it won't propagate on target configs.

Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-06-24 17:10:24 +02:00
Bjørn Mork
d6eebaf995 realtek: fix gcc-12 build with -Werror=array-compare
Removing this gcc-12 error:

arch/mips/rtl838x/setup.c:64:30: error: comparison between two arrays [-Werror=array-compare]
   64 |         else if (__dtb_start != __dtb_end)

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2022-06-22 18:37:40 +02:00
Andreas Böhler
d9e12c21fa realtek: make "u-boot-env" partition writable for Netgear 3xx series
The Netgear GS3xx devices do not properly initialise the port LEDs during
startup unless the boot command in U-Boot is changed. Making the U-Boot
env partition writable allows this modification to be done from within
OpenWrt by calling "fw_setenv bootcmd rtk network on\; boota".

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-06-22 17:52:30 +02:00
Stijn Segers
9c381d3386 realtek: make Netgear GS1xx u-boot env partition writable
Make the u-boot environment partition for the NETGEAR
GS108T v3 and GS110TPP writable (they share a DTS), so
the values can be manipulated from userspace.

See https://forum.openwrt.org/t/57875/1567 for a real
world example.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2022-06-22 17:51:02 +02:00
Pascal Ernster
adbdfc9366 realtek: add support for power LED on Netgear GS108Tv3
The Netgear GS108Tv3 is already supported by OpenWrt, but is missing LED
support. After OpenWrt installation, all LEDs are off which makes the
installation quite confusing.
This enables support for the green/amber power LED to give feedback
about the current status.

This is basically just a verbatim copy of commit c4927747d2 ("realtek:
add support for power LED on Netgear GS308Tv1").

Please note that both LEDs are wired up in an anti-parallel fashion,
which means that only one of both LEDs/colors can be switched on at the
same time. If both LEDs/colors are switched on simultanously, the LED
goes dark.

Tested-by: Pascal Ernster <git@hardfalcon.net>
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
[add title to commit reference]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-06-19 10:58:40 +02:00
Markus Stockhausen
6153c530cc realtek: add support for D-Link DGS-1210-20
Hardware specification
 ----------------------

 * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DRAM
 * 32MB NOR Flash
 * 16 x 10/100/1000BASE-T ports
    - Internal PHY with 8 ports (RTL8218B)
    - External PHY with 8 ports (RTL8218B)
 * 4 x Gigabit RJ45/SFP Combo ports
    - External PHY with 4 SFP ports (RTL8214FC)
 * Power LED
 * Reset button on front panel
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6

 UART pinout
 -----------

  [o]ooo|J6
   | ||`------ GND
   | |`------- RX
   | `-------- TX
   `---------- Vcc (3V3)

 Boot initramfs image from U-Boot
 --------------------------------

  1. Press Escape key during `Hit Esc key to stop autoboot` prompt
  2. Press CTRL+C keys to get into real U-Boot prompt
  3. Init network with `rtk network on` command
  4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command
  5. Boot the image with `bootm` command

To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.

It has been developed and tested on device with F1 revision.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct initramfs image name]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-06-19 08:36:21 +02:00
Andreas Böhler
c4927747d2 realtek: add support for power LED on Netgear GS308Tv1
The Netgear GS308Tv1 is already supported by OpenWrt, but is missing LED
support. After OpenWrt installation, all LEDs are off which makes the
installation quite confusing.
This enables support for the green/amber power LED to give feedback
about the current status.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-06-18 09:21:50 +02:00
Luiz Angelo Daros de Luca
f5a87a0a7b realtek: add gpio-restart for D-Link DGS-1210-28
A GPIO assert is required to reset the system. Otherwise, the system
will hang on reboot.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-06-07 17:11:28 +02:00
Luiz Angelo Daros de Luca
8121e7dd75 realtek: add reset button for D-Link DGS-1210-28
Tested in a DGS-1210-28 F3, both triggering failsafe and reboot.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-06-07 17:11:28 +02:00
John Audia
f800f8d6fc kernel: bump 5.10 to 5.10.120
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800, x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-06 19:20:02 +02:00
John Audia
cd634afe6c kernel: bump 5.10 to 5.10.119
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800, x86/64

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-06-06 19:20:02 +02:00
Raylynn Knight
b515ad10a6 realtek: add support for ZyXEL GS1900-24E
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24E
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB Macronix MX25L12835F
* RAM:       128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet:  24x 10/100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESET" button on front panel
* Switch:    1 Power switch on rear of device
* Power      120-240V AC C13
* UART:      1 serial header (JP2) with populated standard pin connector on
             the left side of the PCB.
             Pinout (front to back):
             + Pin 1 - VCC marked with white dot
             + Pin 2 - RX
             + Pin 3 - TX
             + PIn 4 - GND

Serial connection parameters:  115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Signed-off-by: Raylynn Knight <rayknight@me.com>
2022-06-06 10:30:50 +02:00
Sander Vanheule
bde6311569 realtek: don't unmask non-maskable GPIO IRQs
On uniprocessor builds, for_each_cpu(cpu, mask) will assume 'mask'
always contains exactly one CPU, and ignore the actual mask contents.
This causes the loop to run, even when it shouldn't on an empty mask,
and tries to access an uninitialised pointer.

Fix this by wrapping the loop in a cpumask_empty() check, to ensure it
will not run on uniprocessor builds if the CPU mask is empty.

Fixes: af6cd37f42 ("realtek: replace RTL93xx GPIO patches")
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reported-by: Robert Marko <robimarko@gmail.com>
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-05-30 07:21:03 +02:00
Sander Vanheule
af6cd37f42 realtek: replace RTL93xx GPIO patches
Patches to support the SoC's GPIO controller for RTL930x and RTL931x
devices have been accepted upstream. Replace the current preliminary
patch with the upstream ones, excluding devictree binding changes.

The updated patches add GPIO IRQ balancing support on RTL930x, but this
cannot be used until these devices also support SMP.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-05-22 08:46:50 +02:00
Tony Ambardar
76fae1d169 config: limit CONFIG_DEBUG_INFO to top-level generic configs
Remove redundant target-level entries, noting that these settings will be
configured from "Kernel build options" of Kconfig.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[remove from new configs introduced after patch submission]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-05-18 13:32:06 +03:00
John Audia
8592df67f4 kernel: bump 5.10 to 5.10.114
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-05-16 20:26:38 +02:00
Birger Koblitz
d1b824650f realtek: do not reset SerDes on link change
Do not reset the RTL930x SerDes on link changes, instead set up
the SDS with internal PHYs for the SFP+ ports only.
This fixes the 8 1GBit ports on the Zyxel XGS1250 which
do not work without this patch.

A complete SerDes reset was performed on all SerDes links. For copper
1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There
is however no support for setting up the XGMII link on RTL9300/RTL9310,
thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit
ports. No SerDes reset should be done for these links.

The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely
different. All these modes need to be suitably RX calibrated and the
pre- main and post- amplifiers set up properly for TX.

The 10GBit SFP+ fiber links are recalibrated instead of reset, which
e.g. is necessary when someone pulls a module out and puts another in.
This makes swapping out 10GBit fiber modules possible. 1GBit modules are
not yet supported, nor any modules with an internal phy.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[rewrite commit message based on discussion]
Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-05-11 22:23:50 +02:00
Birger Koblitz
98bb26f9f7 realtek: Trap all frames with switch as destination to CPU-port
This fixes a bug where frames sent to the switch itself were
flooded to all ports unless the MAC address of the CPU-port
was learned otherwise.

Tested-by: Wenli Looi <wlooi@ucalgary.ca>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[fix code formatting]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-05-08 10:05:14 +02:00
Raylynn Knight
580723e86a realtek: add support for ZyXEL GS1900-16
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-16
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB Macronix MX25L12835F
* RAM:       128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet:  16x 10/100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESET" button on front panel
* Power      120-240V AC C13
* UART:      1 serial header (J12) with populated standard pin connector on
             the right back of the PCB.
             Pinout (front to back):
             + Pin 1 - VCC marked with white dot
             + Pin 2 - RX
             + Pin 3 - TX
             + PIn 4 - GND

Serial connection parameters:  115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-05-07 17:23:45 +02:00
Martin Kennedy
a5ac8ad0ba realtek: add ZyXEL GS1900-24HP v1 support
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24HP v1
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB
* RAM:       Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet:  24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
  * 1 PWR LED (green, not configurable)
  * 1 SYS LED (green, configurable)
  * 24 ethernet port link/activity LEDs (green, SoC controlled)
  * 24 ethernet port PoE status LEDs
  * 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
  * 1 "RESET" button on front panel (soft reset)
  * 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
  * Management MCU: ST Micro ST32F100 Microcontroller
  * 6 BCM59111 PSE chips
  * 170W power budget
* Power:     120-240V AC C13
* UART:      Internal populated 10-pin header ('J5') providing RS232;
             connected to SoC UART through a TI or SIPEX 3232C for voltage
             level shifting.

* 'J5' RS232 Pinout (dot as pin 1):
  2) SoC RXD
  3) GND
  10) SoC TXD

Serial connection parameters: 115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface

* Navigate to Maintenance > Firmware > Management

* If "Active Image" has the first option selected, OpenWrt will need to be
  flashed to the "Active" partition. If the second option is selected,
  OpenWrt will need to be flashed to the "Backup" partition.

* Navigate to Maintenance > Firmware > Upload

* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
  file by your preferred method to the previously determined partition.
  When prompted, select to boot from the newly flashed image, and reboot
  the switch.

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).

* Set up a TFTP server on your client and make it serve the initramfs
  image.

* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:

  > rtk network on

* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only be installed in the first partition anyway (hardcoded in the
  DTS). To ensure we are set to boot from the first partition, issue the
  following commands:

  > setsys bootpartition 0
  > savesys

* Download the image onto the device and boot from it:

  > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
  > bootm

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-04-16 17:26:56 +02:00
Hauke Mehrtens
34fb36e165 realtek: Fix tc default package
The tc package does not exits any more, it was split into tc-tiny,
tc-full and tc-bpf. Include tc-bpf by default into realtek images.

This increases the compressed image size by about 232KBytes.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-03-29 13:43:01 +02:00
Hauke Mehrtens
469030659c realtek: Use firewall4
The realtek target is not a router, but basic device, see DEVICE_TYPE.
The basic device type does not come with firewall by default, see
include/target.mk for details. The realtek target extended
DEFAULT_PACKAGES manually with firewall.

This changes the defaults to take firewall4 and nftables instead of
firewall and iptables. This also adds the additional package
kmod-nft-offload.

The only difference to the router type is the missing ppp,
ppp-mod-pppoe, dnsmasq and odhcpd-ipv6only package.

This increases the compressed image size by about 422KBytes.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-03-29 13:42:56 +02:00
Hauke Mehrtens
2acebbdcaa realtek: Remove dnsmasq and odhcpd-ipv6only from default
Do not include the dnsmasq and odhcpd-ipv6only package by default any
more. These services are not needed on a switch. If someone needs this
it is still possible to use opkg or image builder to add them.

This decreases the compressed image size by about 165KBytes.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-03-29 13:42:29 +02:00
John Audia
b04d38a2ea kernel: bump 5.10 to 5.10.106
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-03-19 16:13:58 +01:00
INAGAKI Hiroshi
e83ab243be realtek: add support for Panasonic Switch-M8eG PN28080K
Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on
RTL8380M.

Specification:

- SoC		: Realtek RTL8380M
- RAM		: DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash		: SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet	: 10/100/1000 Mbps x8 + 1
  - port 1-8	: TP, RTL8218B (SoC)
  - port 9	: SFP, RTL8380M (SoC)
- LEDs/Keys	: 7x / 1x
- UART		: RS-232 port on the front panel (connector: RJ-45)
  - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
  - 9600n8
- Power		: 100-240 VAC, 50/60 Hz, 0.5 A
  - Plug	: IEC 60320-C13
- Stock OS	: VxWorks based

Flash instruction using initramfs image:

1.  Prepare the TFTP server with the IP address 192.168.1.111
2.  Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
    the TFTP directory
3.  Download the official upgrading firmware (ex: pn28080k_v30000.rom)
    and place it to the TFTP directory
4.  Boot M8eG and interrupt the U-Boot with Ctrl + C keys
5.  Execute the following commands and boot with the OpenWrt initramfs
    image

    rtk network on
    tftpboot 0x81000000
    bootm

6.  Backup mtdblock files to the computer by scp or anything and reboot
7.  Interrupt the U-Boot and execute the following commands to re-create
    filesystem in the flash

    ffsmount c:/
    ffsfmt c:/

    this step takes a long time, about ~ 4 mins

8.  Execute the following commands to put the official images to the
    filesystem

    updatert <official image>

    example:

      updatert pn28080k_v30000.rom

    this step takes about ~ 40 secs

9.  Set the environment variables of the U-Boot by the following commands

    setenv loadaddr 0xb4e00000
    setenv bootcmd bootm
    saveenv

10: Download the OpenWrt initramfs image and boot with it

    tftpboot 0x81000000 0101A8C0.img
    bootm

11: On the initramfs image, download the sysupgrade image and perform
    sysupgrade with it

    sysupgrade <imagename>

12: Wait ~ 120 seconds to complete flashing

Note:

- "Switch-M8eG" is a model name, and "PN28080K" is a model number.
  Switch-M8eG has an another (old) model number ("PN28080"), it's not a
  Realtek based hardware.

- Switch-M8eG has a "POWER" LED (Green), but it's not connected to any
  GPIO pin.

- The U-Boot checks the runtime images in the flash when booting and
  fails to execute anything in "bootcmd" variable if the images are not
  exsisting.

- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
  firmware and it includes the stock images, configuration files and
  checksum files. It's unknown format, can't be managed on the OpenWrt.
  To get the enough space for OpenWrt, move the filesystem to the head
  of "fs_reserved" partition by execution of "ffsfmt" and "updatert".

- On the other devices in the same series of Switch-M8eG PN28080K, the
  INT pin on the PCA9555 is not connected to anywhere.

Back to the stock firmware:

1. Delete "loadaddr" variable and set "bootcmd" to the original value

   on U-Boot:

     setenv loadaddr
     setenv bootcmd 'bootm 0x81000000'

   on OpenWrt:

     fw_setenv loadaddr
     fw_setenv bootcmd 'bootm 0x81000000'

2. Perform reset or reboot

  on U-Boot:

    reset

  on OpenWrt:

    reboot

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
2022-03-13 19:54:57 +01:00
INAGAKI Hiroshi
da1347d6d6 realtek: enable pca953x driver for rtl838x subtarget
The system status LED on Panasonic Switch-M8eG PN28080K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Sander Vanheule <sander@svanheule.net>
2022-03-13 19:54:57 +01:00
Martin Kennedy
d1a8690742 realtek: add ZyXEL GS1900-24 v1 support
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24 v1
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB
* RAM:       Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet:  24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
  * 1 PWR LED (green, not configurable)
  * 1 SYS LED (green, configurable)
  * 24 ethernet port link/activity LEDs (green, SoC controlled)
  * 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
  * 1 "RESET" button on front panel (soft reset)
  * 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power:     120-240V AC C13
* UART:      Internal populated 10-pin header ('J5') providing RS232;
             connected to SoC UART through a SIPEX 3232EC for voltage
             level shifting.

* 'J5' RS232 Pinout (dot as pin 1):
  2) SoC RXD
  3) GND
  10) SoC TXD

Serial connection parameters: 115200 8N1.

Installation
------------

OEM upgrade method:

* Log in to OEM management web interface

* Navigate to Maintenance > Firmware > Management

* If "Active Image" has the first option selected, OpenWrt will need to be
  flashed to the "Active" partition. If the second option is selected,
  OpenWrt will need to be flashed to the "Backup" partition.

* Navigate to Maintenance > Firmware > Upload

* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
  file by your preferred method to the previously determined partition.
  When prompted, select to boot from the newly flashed image, and reboot
  the switch.

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).

* Set up a TFTP server on your client and make it serve the initramfs
  image.

* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:

  > rtk network on

> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only be installed in the first partition anyway (hardcoded in the
  DTS). To ensure we are set to boot from the first partition, issue the
  following commands:

  > setsys bootpartition 0
  > savesys

* Download the image onto the device and boot from it:

  > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
  > bootm

* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:

  > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
2022-03-13 19:24:13 +01:00
INAGAKI Hiroshi
7b19770525 realtek: add support for I-O DATA BSH-G24MB
I-O DATA BSH-G24MB is a 24 port gigabit switch, based on RTL8382M.

Specification:

- SoC		: Realtek RTL8382M
- RAM		: DDR2 128 MiB (Nanya NT5TU128M8HE-AC)
- Flash		: SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- Ethernet	: 10/100/1000 Mbps x24
  - port 1-8	: RTL8218B
  - port 9-16	: RTL8218B (SoC)
  - port 17-24	: RTL8218B
- LEDs/Keys	: 2x, 1x
- UART		: pin header on PCB
  - JP2: 3.3V, TX, RX, GND from rear side
  - 115200n8
- Power		: 100 VAC, 50/60 Hz
  - Plug	: IEC 60320-C13

Flash instruction using sysupgrade image:

1. Boot BSH-G24MB normally
2. Connect BSH-G24MB to the DHCP enabled network
3. Find the device's IP address and open the WebUI and login
   Note: by default, the device obtains IP address from DHCP server of
         the network
4. Open firmware update page ("ファームウェア アップデート")
5. Rename the OpenWrt sysupgrade image to "bsh-g24mb_v100.image" and
   select it
6. Press apply ("適用") button to perform update
7. Wait ~150 seconds to complete flashing

Note:

- BSH-G24MB has a power-related LED ("電源"), but it's not connected to
  the GPIO of the SoC or RTL8231 and cannot be controlled. Instead of
  it, use system status LED on other than running-state.

- "sys_loop" LED indicates system status and loop-detection status in
  stock firmware.

- BSH-G24MB has 2x os-image partitions named as "RUNTIME"/"RUNTIME2" in
  16 MiB SPI-NOR flash and the size of image per partition is only
  6848 KiB. The secondary image is never used on stock firmware, so also
  use it on OpenWrt to get more space.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-03-07 21:44:53 +01:00
Bjørn Mork
0890fb2df4 realtek: net: dsa: configure better brport flags when ports leave the bridge
Ensures that the DSA driver sets exactly the same default flags as the
bridge when a port joins or leaves.  Without this we end up with a
confusing flag mismatch, where DSA and bridge ports use different sets
of flags.

This is critical as the "learning" mismatch will be harmful to the
network, causing all traffic to be flooded on all ports.

The original commit was buggy, trying to set the flags one-by-one in a
loop.  This was not supported by the API and the end result was that
all but the last flag were cleared.  This bug was implicitly fixed
upstream by commit e18f4c18ab5b ("net: switchdev: pass flags and mask
to both {PRE_,}BRIDGE_FLAGS attributes").

This is a minimum temporary stop measure fix for the critical lack of
"learning" only.  The major API change associated with a full v5.12+
backport is neither required nor wanted. A simpler fix, moving the
call to dsa_port_bridge_flags() out of the loop,  has therefore been
merged into this modified backport.

Fixes: afa3ab54c0 ("realtek: Backport bridge configuration for DSA")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
[fix typos in commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-03-06 22:01:04 +02:00
John Audia
0989b7ad3a kernel: bump 5.10 to 5.10.102
Removed upstreamed:
	bcm4908/patches-5.10/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.102&id=f333c1916fd6b55900029bf8f918cc00009e2111

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-03-01 21:38:36 +01:00
Sander Vanheule
66d8db01cc realtek: remove debugging code from timer
Remove some (dead) debugging code from the Realtek timer to clean up the
sources of this driver.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:58 +00:00
Sander Vanheule
9db651f4a2 realtek: use DT provided address for timers
The I/O base address for the timers was hardcoded into the driver,
or derived from the HW IRQ number as an even more horrible hack. All
supported SoC families have these timers, but with hardcoded addresses
the code cannot be reused right now.

Request the timer's base address from the DT specification, and store it
in a private struct for future reference.

Matching the second interrupt specifier, the address range for the
second timer is added to the DT specification.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:58 +00:00
Sander Vanheule
71810eb068 realtek: clean up RTL930x timer DT node
The Realtek timer node for RTL930x doesn't have any child nodes, making
the use of '#address-cells' quite pointless. It is also not an interrupt
controller, meaning it makes no sense to define '#interrupt-cells'.

The I/O address for this node is also wrong, but this is hidden by the
fact that the driver associated with this node bypasses the usual DT
machinery and does it's own thing. Correct the address to have a sane
value, even though it isn't actually used.

Fixes: a75b9e3ecb ("realtek: Adding RTL930X sub-target")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:58 +00:00
Sander Vanheule
fa20f2bfc7 realtek: ZyXEL GS1900-48: fix system LED polarity
When driven by a GPIO pin, the system LED needs to be configured as
active high. Otherwise the LED switches off after booting and
initialisation.

Fixes: 47f5a0a3ee ("realtek: Add support for ZyXEL GS1900-48 Switch")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Sander Vanheule
66140820e1 realtek: ZyXEL GS1900-48: drop status from gpio1
The default value for a DT node's status property is already "okay", so
there's no need to specify it again. Drop the status property to clean
up the DTS.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Sander Vanheule
a39fbaf23a realtek: use higher priority for timer interrupts
The assigned output index for the event timers was quite low, lower even
than the ethernet interrupt. This means that high network load could
preempt timer interrupts, possibly leading to all sorts of strange
behaviour.

Increase the interrupt output index of the event timers to 5, which is
the highest priority output and corresponds to the (otherwise unused)
MIPS CPU timer interrupt.

Fixes: a75b9e3ecb ("realtek: Adding RTL930X sub-target")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Sander Vanheule
4b31717fb0 realtek: move RTL8231 definitions to board files
The RTL8231 is an external chip, and not part of the SoC. That means
it is more appropriate to define it in the board specific (base) files,
instead of the DT include for the SoC itself.

Moving the RTL8231 definition also ensures that boards with no GPIO
expander, or an alternative one, don't have a useless gpio1 node label
defined.

Tested on a Netgear GS110TPPv1.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Sander Vanheule
004d4d66c8 realtek: fix node addresses for RTL839x
The address in some node names doesn't match the actual offset specified
in the DT node. Update the names to fix this.

While fixing the node names, also drop the unused node labels.

Fixes: 0a7565e536 ("realtek: Update rtl839x.dtsi for realtek,rtl-intc, new gpio controller remove RTL8231 node")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Sander Vanheule
1ca081000a realtek: consolidate bootargs again
Bootargs for devices in the realtek target were previously consolidated
in commit af2cfbda2b ("realtek: Consolidate bootargs"), since all
devices currently use the same arguments.

Commit a75b9e3ecb ("realtek: Adding RTL930X sub-target") reverted this
without any argumentation, so let's undo that.

Commit 0b8dfe0851 ("realtek: Add RTL931X sub-target") introduced the
old bootargs also for RTL931x, without providing any actual device
support. Until that is done, let's assume vendors will have done what
they did before, and use a baud rate of 115200.

Fixes: a75b9e3ecb ("realtek: Adding RTL930X sub-target")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-02-20 16:23:55 +00:00
Birger Koblitz
4d8020072e realtek: fix locking bug in rtl838x_hw_receive()
A Locking bug in the packet receive path was introduced with PR
#4973. The following patch prevents the driver from locking
after a few minutes with an endless flow of

[ 1434.185085] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000f8
[ 1434.208971] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc
[ 1434.794800] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc
[ 1435.049187] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
2022-02-18 12:35:03 +00:00
Sander Vanheule
a93dfff10e realtek: add RTL8231 chip detection
When initialising the driver, check if the RTL8231 chip is actually
present at the specified address. If the READY_CODE value does not match
the expected value, return -ENXIO to fail probing.

This should help users to figure out which address an RTL8231 is
configured to use, if measuring pull-up/-down resistors is not an
option.

On an unsuccesful probe, the driver will log:
    [    0.795364] Probing RTL8231 GPIOs
    [    0.798978] rtl8231_init called, MDIO bus ID: 30
    [    0.804194] rtl8231-gpio rtl8231-gpio: no device found at bus address 30

When a device is found, only the first two lines will be logged:
    [    0.453698] Probing RTL8231 GPIOs
    [    0.457312] rtl8231_init called, MDIO bus ID: 31

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-17 19:11:42 +02:00
Sander Vanheule
44f7cfd760 realtek: always require SMI bus ID for RTL8231
The SMI bus ID for RTL8231 currently defaults to 0, and can be
overridden from the devicetree. However, there is no value check on the
DT-provided value, aside from masking which would only cause value
wrap-around.

Change the driver to always require the "indirect-access-bus-id"
property, as there is no real reason to use 0 as default, and perform a
sanity check on the value when probing. This allows the other parts of
the driver to be simplified a bit.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-17 19:11:37 +02:00
Sander Vanheule
5da2e0cc20 realtek: use automatic GPIO numbering for RTL8231
Set the gpio_chip.base to -1 to use automatic GPIO line indexing.
Setting base to 0 or a positive number is deprecated and should not be
used.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-17 19:11:33 +02:00
Sander Vanheule
851212a714 realtek: fix RTL8231 gpio count
The RTL8231's gpio_chip.ngpio was set to 36, which is the largest valid
GPIO index. Fix the allowed number of GPIOs by setting ngpio to 37, the
actual line count.

Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-02-17 19:11:17 +02:00
Daniel Golle
eef7f17652 realtek: rtl83xx-phy: abstract and document PHY features
Replace magic values with more self-descriptive code now that I start
to understand more about the design of the PHY (and MDIO controller).

Remove one line before reading RTL8214FC internal PHY id which turned
out to be a no-op and can hence safely be removed (confirmed by
INAGAKI Hiroshi[1])

[1]: df8e6be59a (r66890713)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-02-17 15:37:03 +00:00
Birger Koblitz
68c66b0fa3 realtek: fix locking issues
Fixe a coupld of locking issues found by applying lock
debugging to the code.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Daniel Golle
b53202a8c3 realtek: switch to use generic MDIO accessor functions
Instead of directly calling SoC-specific functions in order to access
(paged) MII registers or MMD registers, create infrastructure to allow
using the generic phy_*, phy_*_paged and phy_*_mmd functions.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-02-17 15:21:47 +00:00
Daniel Golle
af93bf6129 realtek: implement Clause-45 MDIO write on rtl931x
* Add missing Clause-45 write support for rtl931x
 * Switch to use helper functions in all Clause-45 access functions to
   make the code more readable.
 * More meaningful/unified debugging output (dynamic kprintf)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-02-17 15:21:47 +00:00
Daniel Golle
854458f986 realtek: backport Clause-45 MDIO helper functions
Import commit ("c6af53f038aa3 net: mdio: add helpers to extract clause
45 regad and devad fields") from Linux 5.17 to allow making the MDIO
code in the ethernet driver more readable.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-02-17 15:21:47 +00:00
Birger Koblitz
0538dc693b realtek: add support for port led configuration on RTL93XX
Using the led-set attribute of a port in the dts we allow configuration
of the port leds. Each led-set is being defined in the led-set configuration
of the .dts, giving a specific configuration to steer the port LEDs via a serial
connection.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
caaac9ab3b realtek: Add support for the RTL8221B PHY
The RTL8221B PHY is a newer version of the RTL8226, also supporting
2.5GBit Ethernet. It is found with RTL931X devices such as the
EdgeCore ECS4125-10P

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
08cf48c344 realtek: Add specific PHY polling options to support the Zyxel XGS1250/XGS1210
Both the Aquantia AQR113c and the RTL8226 PHYs in the Zyxel XGS1250 and the
Zyxel XGS1210 require special polling configuration settings in the
RTL930X_SMI_10GPHY_POLLING_REGxx_CFG configuration registers. Set them.
Additionally, for RTL 1GBit phys set the RTL930X_SMI_PRVTE_POLLING_CTRL bits
in the poll mask.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
3cab11ad13 realtek: Fix link status detection on RTL9302 for SFP modules
For SFP slots on the RTL9302, the link status is not correctly detected.
Use the link media status instead.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
0b8dfe0851 realtek: Add RTL931X sub-target
We add the RTL931X sub-target with kernel configuration for
a dual core MIPS InterAptive CPU.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
9ed6097054 realtek: Add HW support for RTL931X for PIE, L2 and STP aging
We add HW support routines for the RTL931X SoC family for handling
the Packet Inspection Engine, L2 table handling and STP aging.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
724e4af530 realtek: Store and Restore MC memberships for port enable/disable
We need to store and restore MC memberships in HW when a port joins or
leaves a bridge as well as when it is enabled or disabled, as these
properties should not change in these situations.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
d22923be66 realtek: Copy all BPDUs to the kernel
In order to receive STP information at the kernel level, we make sure
that all Bridge Protocol Data Units are copied to the CPU-Port.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
9d396fc1e8 realtek: Add L2 aging configuration functions for all SoC families
Instead of a generic L2 aging configuration function with complex
logic, we implement an individual function for all SoC types.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
f3c5e7ddcc realted: Add DSA bridge offload configuration
Add functionality to enable or disable L2 learning offload and port flooding
for RTL83XX.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
afa3ab54c0 realtek: Backport bridge configuration for DSA
Adds the DSA API for bridge configuration (flooding, L2 learning,
and aging) offload as found in Linux 5.12 so that we can implement
it in our drivver.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
32e5b5ee6b realtek: Add Link Aggregation (aka trunking) support
This adds LAG support for all 4 SoC families, including support
ofr the use of different distribution algorithm for the load-
balancing between individual links.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
8557b458e2 realtek: Backport LAG functionality for DSA
Add the LAG configuration API for DSA as found in Linux 5.12 so that we
can implement it in the dsa driver.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
77f3e2ea17 realtek: Cleanup setting inner/outer PVID and Ingress/Egres VLAN filtering
Use setting functions instead of register numbers in order to clean up the code.
Also use enums to define inner/outer VLAN types and the filter type.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
5b8b382df9 realtek: Add support for ZxXEL XGS1250-12 Switch
The ZyXEL XGS1250-12 Switch is a 11 + 1 port multi-GBit switch with
8 x 1000BaseT, 3 x 1000/2500/5000/10000BaseT Ethernet ports and
1 SFP+ module slot.

Hardware:
 - RTL9302B SoC
 - Macronix MX25L12833F (16MB flash)
 - Nanja NT5CC64M16GP-1 (128MB DDR3 SDRAM)
 - RTL8231 GPIO extender to control the port LEDs
 - RTL8218D 8x Gigabit PHY
 - Aquantia AQR113c 1/2.5/5/10 Gigabit PHYs
 - SFP+ 10GBit slot

Power is supplied via a 12V 2A standard barrel connector. At the
right side behind the grid is UART serial connector. A Serial
header can be connected to from the outside of the switch trough
the airvents with a standard 2.54mm header.
Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial
connection is via 115200 baud, 8N1.

A reset button is accessble through a hole in the front panel

At the time of this commit, all ethernet ports work under OpenWRT,
including the various NBaseT modes, however the 10GBit SFP+ slot is not
supported.

Installation
--------------
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* Navigate to 'Management' in the OEM web interface and click on 'Firmware upgrade'
  to the left.
* Upload the OpenWrt initramfs image, and wait till the switch reboots.
* Connect to the device through serial and change the U-boot boot command.
  > fw_setenv bootcmd 'rtk network on; boota'
* Reboot, scp the sysupgrade image to /tmp, verify the checksum and flash it:
  > sysupgrade /tmp/openwrt-realtek-rtl930x-zyxel_xgs1250-12-squashfs-sysupgrade.bin
* Upon reboot, you have a functional OpenWrt installation. Leave the bootcmd
  value as is - without 'rtk network on' the switch will fail to initialise
  the network.

Web recovery
------------
The XGS1250-12 has a handy web recovery that will load when U-boot does
not find a bootable kernel. In case you would like to trigger the web
recovery manually, partially overwrite the firmware partition with some
zeroes:

  # dd if=/dev/zero of=/dev/mtd5 bs=1M count=2

If you have serial connected you'll see U-boot will start the web recovery
and print it's listening on 192.168.1.1, but by default it seems to be on
the OEM default IP for the switch - 192.168.1.3. The web recovery only
listens on HTTP (80) and *not* on 443 (HTTPS) unlike the web UI.

Return to stock
---------------
You can flash the ZyXEL firmware images to return to stock:

  # sysupgrade -F -n XGS1250-12_Firmware_V1.00(ABWE.1)C0.bix

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
400676e442 realtek: Add RTL930X sub-target
Adds the sub-target for the RTL930X-based routers. Adds an
initial kernel configuration.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
7026084066 realtek: Add SDS configuration routines for the RTL93XX platforms
Adds configuration routines for the internal SerDes of the
RTL930X and RTL931X.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
51c8f76612 realtek: Improve MAC config handling for all SoCs
Adds a rtl931x_phylink_mac_config for the RTL931X and improve
the handling of the RTL930X phylink configuration. Add separate
handling of the RTL839x since some configurations are different
from the RTL838X.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
c7cc4e95a5 realtek: Add support for detecting RTL9303 SoCs
Adds support for detecting RTL9303 SoCs as found e.g.
in the Ubiquiti USW switch.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
60df655d5b realtek: Allow PHY-IDs to differ from Port numbers
We were using the PHY-ids (the reg entries in the PHY
sections of the .dts) as the port numbers. Now scan the
ports section in the .dts, and use the actual port numbers,
following the phy-handle to the PHY properties.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
bf0ffe3310 realtek: Use SerDes Information from .dts for phylink config
When a port is brought up, read the SDS-id via the phy_device
for a given port and use this to configure the SDS when it
is brought up.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
8079574f2c realtek: Remove RTL838X PHY firmware from RTL839X kernel
The RTL839X does not have an internal phy and thus does not need to have any
firmware as part of the kernel, especially not firmware for the RTL838X.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
a825835942 realtek: Improve IRQ request in Ethernet driver
Improves the IRQ request code by using platform_get_irq() which provides
better error handling.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
a75b9e3ecb realtek: Adding RTL930X sub-target
This adds the RTL931X sub-target in the realtek target Makefile.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
5cb2828092 realtek: Use new CEVT timer
Selects the new CEVT timer for Realtek instead of the previous
timer driver. While we are at it, we explicitily state we do
not use the I2C driver of the RTL9300.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
775d903216 realtek: Replace the RTL9300 generic timer with a CEVT timer
The RTL9300 has a broken R4K MIPS timer interrupt, however, the
R4K clocksource works. We replace the RTL9300 timer with a
Clock Event Timer (CEVT), which is VSMP aware and can be instantiated
as part of brining a VSMTP cpu up instead of the R4K CEVT source.
For this we place the RTL9300 CEVT timer in arch/mips/kernel
together with other MIPS CEVT timers, initialize the SoC IRQs
from a modified smp-mt.c and instantiate each timer as part
of the MIPS time setup in arch/mips/include/asm/time.h instead
of the R4K CEVT, similarly as is done by other MIPS CEVT timers.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
0536c582e6 realtek: Fix RTL931X Ethernet driver
Various fixes to enable Ethernet on the RTL931X:
 - Network start and stop sequence for RTL931X HW
 - MDIO access on RTL931X SoC
 - Chip initialization
 - SerDes setup

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
1b1f05f682 realtek: Fix Ethernet driver IRQ service routine for SMP
Do not lock the register structure in IRQ context. It is not
necessary and leads to lockups under SMP load.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
9d847244d9 realtek: fix RTL839X receive tag decoding
Correct offset in RX tag structure. Correct offload decision flagging.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
6b79484268 realtek: Add SerDes access functions for RTL931X
Adds RTL931X SerDes access functions as needed by the Ethernet driver.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
6378d72ef6 realtek: Fix RTL931X-specific Ethernet driver functions
Fix the update counter of the RX ring, add SDS access functions
for RTL931X.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
9024202052 realtek: rename rtl838x_reg structure
Rename the SoC-specific rtl838x_reg structure in the Ethernet
driver to avoid confusion with the structure of the same name
in the DSA driver. New name is: rtl838x_eth_reg

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
2f51e567ff realtek: Fix RTL839x TX CPU-Tag
Setting bits 20 and 23 in a u16 is obviously wrong.
According to https://www.svanheule.net/realtek/cypress/cputag
cpu_tag[2] starts at bit 48 in the cpu-tag structure, so
bit 43 is bit 5 in cpu_tag[2] and bit 40 is bit 8 in
cpu_tag[2].

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
b3287a2165 realtek: Increase zone size for Ethernet driver DMA
Set CONFIG_FORCE_MAX_ZONEORDER setting to 13 to allow larger
contiguous memory allocation for the DMA of the Ethernet
driver. Increase the number of entries in the RX ring
to 300 making use of the larger DMA region now possible for
receiveing packets.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
47f5a0a3ee realtek: Add support for ZyXEL GS1900-48 Switch
The GS1900-48 is a 48 + 2 port Gigabit L2 switch with 48 gigabit ports.
Hardware:
    RTL8393M SoC
    Macronix MX25l12805D (16MB flash)
    128MB RAM
    6 * RTL8218B external PHY
    2 * RTL8231 GPIO extenders to control the port LEDs, system LED and
    Reset button

2 Uplink ports are SFP cages which support 1000 Base-X mini GBIC modules.

Power is supplied via a 230 volt mains connector.
The board has a hard reset switch SW1, which is is not reachable from the outside.
J4 provides a 12V RS232 serial connector which is connected through U8 to
the 3.3V UART of the RTL8393. Conversion is done by U8, a SIPEX 3232EC.
To connect to the UART, wires can be soldered to R603 (TX)  and R602 (RX).

Installation:
Install the squashfs image via Realtek's original Web-Interface.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
0a7565e536 realtek: Update rtl839x.dtsi for realtek,rtl-intc, new gpio controller remove RTL8231 node
Update the IRQ configuration to work with the new rtl-intc controller.
Also change all KSEG1 addresses in reg = <> of the devics to physical
addresses.

Use the new gpio-otto controller instead of the legacy driver.
Also remove the memory node as this is better put into a device .dts.

Also remove the RTL8231 GPIO controller node from this base file
since the chip might not be found in all Realtek RTL839x devices.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
1df2f8d831 realtek: Update RTL838X DTS to new Realtek IRQ controller notation
Replace the interrupt controller node with the new realtek,rtl-intc
node and change all device interrupts to use the 2 field notation:
interrupts = <[SoC IRQ] [Index to MIPS IRQ]>

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
6c18e9c491 realtek: Add VPE support for the IRQ driver
In order to support VSMP, enable support for both VPEs
of the RTL839X and RTL930X SoCs in the irq-realtek-rtl
driver. Add support for IRQ affinity setting.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
0c9f614c99 realtek: Add kernel config for RTL839x SoCs
Adds a dedicated kernel configuration for RTL839X SoCs
enabling SMP.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
04489b7255 realtek: Enable Multithreading support in prom.c
Adds Multithreading support functions in prom.c.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
f603090311 realtek: Change Platform defines to depend on CONFIG_RTL83XX
In order for the Platform includes to be available on
all sub-targets, make them dependent on CONFIG_RTL83XX.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
4021dd527b realtek: Optimize kernel configuration for RTL838X
The RTL838X SoCs do not use Aquantia PHYs, remove this.
Also the RTL838X uses a high resolution R4K timer.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
fce11f6849 realtek: Create 4 different Realtek Platforms
Creates RTL83XX as a basic kernel config parameter for the
RTL838X, RTL839x, RTL930X and RTL931X platforms with respective
configurations for the SoCs, which are introduced in addition.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
0d7cace7bd realtek: Create rtl838x sub-target specific makefiles
Create the RTL838x specific Makefiles. Move CPU-type into
rtl838x.mk as this is specifc to that platform. Add
rtl838x subtarget into main Makefile.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:47 +00:00
Birger Koblitz
47be1943ed realtek: Add initial kernel config for RTL838x sub-target
Move the generic kernel configs to the rtl838x sub-target.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
8de54c2ce6 realtek: Add Makefile for RTL839x sub-architecture
Adds the initial Makefile for the RTL839x sub-architecture.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
cf8e145955 realtek: Set RTL838X sub-target specific properties
This defines the sub-target specific properties for the RTL838X
sub-target.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
14705ae3bd realtek: Create rtl838x subtarget
mv generic/target.mk to rtl838x/target.mk in order to create
an initial makefile for the rtl838x sub-architecture

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
45053b507c realtek: Add support for SFP EEPROM-access over SMBus
The EEPROMs on SFP modules are compatible both to I2C as well
as SMBus. However, the kernel so far only supports I2C
access. We add SMBus access routines, because the I2C driver
for the RTL9300 HW only supports that protocol. At the same
time we disable I2C access to PHYs on SFP modules as otherwise
detection of any SFP module would fail. This is not in any
way problematic at this point in time since the RTL93XX
platform so far does not support PHYs on SFP modules.

The patches are copied and rebased version of:
https://bootlin.com/blog/sfp-modules-on-a-board-running-linux/

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
f4bdb7fdcc realtek: Add support for RTL9300/RTL9310 I2C multiplexing
The RTL9300/RTL9310 I2C controllers have support for 2 independent I2C
masters, each with a fixed SCL pin, that cannot be changed. Each of these
masters can use 8 (RTL9300) or 16 (RTL9310) different pins for SDA.
This multiplexer directly controls the two masters and their shared
IO configuration registers to allow multiplexing between any of these
busses. The two masters cannot be used in parallel as the multiplex
is protected by a standard multiplex lock.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
63a0a4d85b realtek: Add support for RTL9300/RTL9310 I2C controller
This adds support for the RTL9300 and RTL9310 I2C controller.
The controller implements the SMBus protocol for SMBus transfers
over an I2C bus. The driver supports selecting one of the 2 possible
SCL pins and any of the 8 possible SDA pins. Bus speeds of
100kHz (standard speed) and 400kHz (high speed I2C) are supported.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
48dd446614 realtek: remove legacy GPIO driver support
This patch removes support for the legacy GPIO driver, since now
the gpio-otto driver can be used on all platforms

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Birger Koblitz
2314ba725b realtek: Add GPIO support for RTL930X and RTL931X
We add support for the RTL930X and RTL931X architectures
in the gpio-realtek-otto.c driver.

Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2022-02-17 15:21:46 +00:00
Daniel Golle
58b82e6ca5 realtek: drop support for Linux 5.4
Drop patches and files for Linux 5.4 now that we've been using 5.10
for a while and support for Linux 5.4 has gone out-of-sync.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-02-17 15:21:46 +00:00
John Audia
c391dcdf86 kernel: bump 5.10 to 5.10.100
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-02-11 23:17:40 +01:00
John Audia
5e43dd1fa7 kernel: bump 5.10 to 5.10.99
Had to update generic defconfig (make kernel_menuconfig CONFIG_TARGET=generic)
for this bump, but since that only modifies the target defined in .config,
and since that target also needed to be updated for unrelated reasons, manually
propagated the newly added symbol to the generic config.

Removed upstreamed:
    pending-5.10/860-Revert-ASoC-mediatek-Check-for-error-clk-pointer.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.99&id=080f371d984e8039c66db87f3c54804b0d172329

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <graysky@archlinux.us>
2022-02-11 23:17:40 +01:00
John Audia
7bf62e2451 kernel: bump 5.4 to 5.4.169
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*Had to revert 7f1edbd in order to build due to FS#4149

Signed-off-by: John Audia <graysky@archlinux.us>
2022-01-03 01:00:03 +01:00
Sander Vanheule
ebc0ce118f realtek: netgear-gs110tpp: Add system LEDs
The GS110TPP has an RGB LED used for system status indication. Expose
all three components as separate GPIO LEDs connected via the device's
RTL8231.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-27 13:51:41 +01:00
Sander Vanheule
c88124cfc4 realtek: netgear-gigabit: Enable RTL8231
Since the move to 5.10, there are now two GPIO drivers. The gpio0 node
refers to the internal GPIOs, so the indirect-access-bus-id is no longer
relevant for that node.

Set indirect-access-bus-id to the correct value (31) on the correct node
(gpio1) and enable the device.

Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
2021-12-27 13:51:41 +01:00
Sergey Ryazanov
fa3690f8f1 kernel: 5.10: consolidate mac80211 crypto options
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2

either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.

CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
John Audia
43c0a12665 kernel: bump 5.10 to 5.10.85
Removed target for patch which does not exist:
    bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch

All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*

* Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-17 15:10:22 +01:00
John Audia
6c945fa379 kernel: bump 5.10 to 5.10.83
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1]
    bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6

Build system: x86_64*
Build-tested: bcm2711/RPi4B, ipq806x/R7800†
Run-tested: bcm2711/RPi4B, ipq806x/R7800†

* Had to revert 7c99085bd6 in order to build
  (latest bump of ca-certificates)

† Had to revert 7f1edbd412 in order to build
  (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)

Signed-off-by: John Audia <graysky@archlinux.us>
2021-12-12 21:11:30 +01:00
Bjørn Mork
afeda4a3d3 realtek: sort the port list numerically
Mac adresses are assigned in the order given by the port list.  The
interfaces are also brought up in this order.  This target supports
devices with up to 52 ports.  Sorting these alphabetically is very
confusing, and assigning mac addresses in alphabetic order does not
match stock firmware behaviour.

Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-12-05 18:49:14 +01:00
Sander Vanheule
4304799b4a realtek: update watchdog timer patch
The Realtek Otto watchdog timer driver was accepted upstream, and is
queued for 5.17. Update the patch's file name, and replace by the final
version.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-12-05 18:49:14 +01:00
Sander Vanheule
22f85d63cf realtek: netgear-gigabit: Add gpio-restart node
The Netgear GS110TPP v1 switch cannot reliably perform cold reboots
using the system's internal reset controller.

On this device, and the other supported Netgear switches, internal GPIO
line 13 is connected to the system's hard reset logic. Expose this GPIO
on all systems to ensure restarts work properly.

Cc: Raylynn Knight <rayknight@me.com>
Cc: Michael Mohr <akihana@gmail.com>
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Bjørn Mork <bjorn@mork.no>
2021-11-28 22:43:08 +01:00
Sander Vanheule
3f4d6da453 realtek: Enable gpio-restart driver
Add the gpio-restart driver to the realtek build. This way devices,
which cannot reliably perform resets using the SoC's internal reset
logic, can use a GPIO line to drive the SoC's hard reset input.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-28 22:43:08 +01:00
Sander Vanheule
fa71139776 realtek: add missing GPIO irq properties
The internal GPIO controller on RTL838x is also an IRQ controller, which
requires the 'interrupt-controller' and '#interrupts-cells' properties
to be present in the device tree.

Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-28 22:43:08 +01:00
Bjørn Mork
d1464afe1b realtek: use full range of assigned MAC addresses
Some devices are assigned globally unique MAC addresses for all
ports. These are stored by U-Boot in the second U-Boot enviroment
("sysinfo") as a range of start and end address.

Use the full range if provided.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-11-28 22:43:08 +01:00
Bjørn Mork
9e7149f729 realtek: revert to "standard" management configuration
The default management interface should be easy to find for users
doing "blind" installations without console access.  There are
already multiple examples in the forum of advanced early adopters
having problems locating the management interface after installing
OpenWrt.

Requiring tagged VLAN configration to access the initial management
interface creates unnecessary hassle at best. Errors on the other
end are close to impossible to debug without console access, even
for advanced users.  Less advanced users might have problems with
the concept of VLAN tagging.

Limiting management access to a single arbitrary port among up to
52 possible LAN ports makes this even more difficult, for no
reason at all. Users might have reasons to use a different port
for management.  And they might even have difficulties using the
OpenWrt selected one. The port might be the wrong type for their
management link (e.g copper instead of fibre).  Or they might
depend on PoE power from a device which they can't reconfigure.

User expectations will be based on
- OpenWrt defaults for other devices
- stock firmware default for the device in question
- common default behaviour of similar devices

All 3 cases point to a static IP address accessible on the native
VLAN of any LAN port.  A switch does not have any WAN port.  All
ports are LAN ports.

This changes the default network configuration in line with these
expectations.

Cc: John Crispin <john@phrozen.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-11-28 22:33:57 +01:00
John Audia
81995a5e77 kernel: bump 5.4 to 5.4.162
All patches automatically rebased.

Build system: x86_64
Build-tested: ramips/mt7621*

*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-28 16:32:45 +01:00
John Audia
bbdc13b15b kernel: bump 5.4 to 5.4.161
Removed upstreamed:
    ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch[1]

Manually rebased:
    layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
    octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch

All other patches automatically rebased.

1. Private email exchange with patch author, Hauke Mehrtens

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-28 16:32:45 +01:00
John Audia
894f483d20 kernel: bump 5.10 to 5.10.82
Removed upstreamed:
    bcm53xx/patches-5.10/033-v5.16-0014-ARM-dts-NSP-Fix-mpcore-mmc-node-names.patch

Manually rebased:
    ipq806x/patches-5.10/086-ipq8064-fix-duplicate-node.patch

All other patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800
Run-tested: bcm2711/RPi4B, ipq806x/R7800

Signed-off-by: John Audia <graysky@archlinux.us>
2021-11-27 19:19:30 +01:00
Sander Vanheule
f8b2bc550b realtek: Remove _machine_restart and _machine_halt
By dropping _machine_restart, users can provide more reliable or
device-specific restart modes.

_machine_halt was already removed in commit f4b687d1f0 ("realtek: use
kernel defined halt"), but quietly reintroduced in commit 8faffa00cb
("realtek: add support for the RTL9300 timer"). Let's remove it again.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:56 +02:00
Sander Vanheule
927570f0a3 realtek: Add and enable watchdog node
Add and enable the Realtek Otto WDT peripheral found on these SoCs.

Default all devices to use standard (cold) reboot and "soc" resets.

Devices that require the PLL value fixup before restarting, should pick
the "cpu" or "software" reset mode. These devices also need to provide a
custom reboot mode, by adding the reboot argument to the kernel command
line:

    WDT reset mode  | kernel reboot mode
    ----------------+---------------------------------------
    soc             | reboot=cold (default if not specified)
    cpu             | reboot=warm
    software        | reboot=software

Preferrably, these devices should use an alternative restart method like
gpio-restart to provide reliable restarts.

Note that watchdog restarts are not yet exposed, since the
_machine_restart override is still present.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:42 +02:00
Sander Vanheule
b8fc5eecdc realtek: Backport Realtek Otto WDT driver
Add patch submitted upstream to linux-watchdog and replace the MIPS
architecture symbols. Requires one extra patch for the DIV_ROUND_*
macros, which have moved to a different header since 5.10.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:43:21 +02:00
Sander Vanheule
d3a62bea08 realtek: Add Lexra bus clock
The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the
Lexra bus. This bus can provide a clock signal to these peripherals, but
no clock driver is currently available. Instead, use a fixed-clock to
provide the clock frequency, and update the dependent peripherals.

Lexra bus clock frequencies:
- RTL838x: 200MHz
- RTL839x: 200MHz
- RTL930x: 175MHz

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:42:56 +02:00
Sander Vanheule
af2cfbda2b realtek: Consolidate bootargs
All current devices use identical bootargs, so let's move that to the
common devicetree includes.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:42:44 +02:00
Sander Vanheule
72ae8314f5 realtek: reset both ethernet NIC and queues
Recent versions of Realtek's SDK reset both the ethernet NIC and queues
(SW_NIC_RST and SW_Q_RST bits) when initialising the hardware.

Furthermore, when issuing a CPU reset on the Zyxel GS1900-8 (not
supported by any current driver), the networking part of the SoC is not
reset. This leads to unresponsive network after the restart. By
resetting both the ethernet NIC and queues, networking always comes up
reliably.

Suggested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-11-24 21:38:43 +02:00
Rui Salvaterra
3ae5da5adc kernel: bump 5.10 to 5.10.80
Deleted (upstreamed):
ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch [1]
bcm53xx/patches-5.10/033-v5.15-0012-ARM-dts-BCM5301X-Fix-memory-nodes-names.patch [2]
lantiq/patches-5.10/0016-mtd-rawnand-xway-Keep-the-driver-compatible-with-on-.patch [3]
lantiq/patches-5.10/0110-MIPS-lantiq-dma-add-small-delay-after-reset.patch [4]
lantiq/patches-5.10/0111-MIPS-lantiq-dma-reset-correct-number-of-channel.patch [5]
lantiq/patches-5.10/0112-MIPS-lantiq-dma-fix-burst-length-for-DEU.patch [6]

Manually rebased:
ipq806x/patches-5.10/0065-arm-override-compiler-flags.patch

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=47462c5e600fbaffd755cd13dedd80d04e41ff83
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=2fde76df1885a6bec04317e457121326070450eb
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=9b366f5221d8aa64b22f35be137a5749326444ce
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=5af57ce8a6155fe3e4270d28d171abf8903bebc0
[5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=b92a5df2c7adc79a57481445f67de0c1c716581f
[6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=6b72caabc47011d03f44064452b2c65e8ed18326

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-11-19 09:40:29 +00:00
Sander Vanheule
c735d2e218 realtek: backport GPIO IRQ index fix
Backport the patch queued upstream for 5.16. The patch differs slightly
from the upstream patch due to an upstream change that added a
convenience function.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-11-01 00:56:51 +01:00
Rui Salvaterra
02026d0a6f kernel: bump 5.10 to 5.10.76
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]

Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-10-30 21:17:20 +02:00
Bjørn Mork
d990f805c0 realtek: re-enable IPv6 routing
Commit 03e1d93e07 ("realtek: add driver support for routing
offload") added routing offload for IPv4, but broke IPv6 routing
completely.  The routing table is empty and cannot be updated:

 root@gs1900-10hp:~# ip -6 route
 root@gs1900-10hp:~# ip -6 route add unreachable default
 RTNETLINK answers: Invalid argument

As a side effect, this breaks opkg on IPv4 only systems too,
since uclient-fetch fails when there are no IPv6 routes:

 root@gs1900-10hp:~# uclient-fetch http://192.168.99.1
 Downloading 'http://192.168.99.1'
 Failed to send request: Operation not permitted

Fix by returning NOTIFY_DONE when offloading is unsupported, falling
back to default behaviour.

Fixes: 03e1d93e07 ("realtek: add driver support for routing offload")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-10-30 15:00:22 +02:00
Bjørn Mork
daefc646e6 realtek: fix ZyXEL initramfs image generation
The current rule produces empty trailers, causing the OEM firmware
update application to reject our images.

The double expansion of a makefile variable does not work inside
shell code.  The second round is interpreted as a shell expansion,
attempting to run the command ZYXEL_VERS instead of expanding the
$(ZYXEL_VERS) makefile variable.

Fix by removing one level of variable indirection.

Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Tested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-10-30 15:00:22 +02:00
Rui Salvaterra
d4f0e45f90 kernel: bump 5.10 to 5.10.75
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0735-xhci-guard-accesses-to-ep_state-in-xhci_endpoint_res.patch [1]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=dc3e0a20dbb9dbaa22f4a33dea34230f8c663c40

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-10-21 00:17:36 +02:00
Rui Salvaterra
72e53eb133 kernel: bump 5.10 to 5.10.74
Patches automatically refreshed.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-10-21 00:17:36 +02:00
John Audia
0ea33e5363 kernel: bump 5.4 to 5.4.155
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-21 00:17:36 +02:00
John Audia
3d0499bcdb kernel: bump 5.4 to 5.4.154
All patches automatically rebased.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-21 00:17:36 +02:00
Adrian Schmutzler
352427ecec realtek: switch to kernel 5.10
The usual testers did their tests. Now we need testers who use the
master builds.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-20 23:27:52 +02:00
John Audia
e672d1b387 kernel: bump 5.10 to 5.10.72
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <graysky@archlinux.us>
2021-10-10 00:09:22 +01:00
Birger Koblitz
cda0460ad3 realtek: add legacy realtek GPIO driver for rtl9300 support
The otto GPIO driver does not work with rtl9300 SoCs. Add
the legacy driver again and use that by default in the 9300 .dtsi

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
4c83dae801 realtek: enable Aquantia PHY support
Enables Aquantia PHY support in the kernel

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
76f60470a1 realtek: Fix bug when accessing external PHYs on SoCs older than Revision C
RTL8393 SoCs older than Revision C hang on accesses to PHYs with PHY address
larger or equal to the CPU-port (52). This will make scanning the MDIO bus
hang forever. Since the RTL8390 platform does not support more than
52 PHYs, return -EIO for phy addresses >= 52. Note that the RTL8390 family
of SoCs has a fixed mapping between port number and PHY-address.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
88936e7e82 realtek: cleanup PHY driver
Removes unnecessary output from the RTL PHY drivers.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
1cfd45ae0b realtek: Add debugfs support for RTL9300
Adds support for debugfs on RTL9300, in particular the drop counters.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
1f402512ae realtek: Add SoC-specific routing offload implementation
Adds SoC specific routing offload implementations for
RTL8380/90 and RTL9300. RTL83xx supports merely nexthop
routing, RTL9300 full host and prefix routes.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
03e1d93e07 realtek: add driver support for routing offload
Add generic support for listening to FIB and Event notifier updates and
use this information to hook into the L3 hardware capabilities of the
RTL SoCs.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
ee6f483a62 realtek: Improve MDIO bus probing for RTL9300
Improve handling of multi-gig ports on the RTL9300 when probing
the MDIO bus.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
9ae927febd realtek: Fix bug in VLAN ingress and egress filtering
The ingress filter registers use 2 bits for each port to define the filtering
state, whereas the egress filter uses 1 bit. So for for the ingress filter
the register offset for a given port is:
(port >> 4) << 4: since there are 16 entries in a register of 32 bits
and for the egress filter:
(port >> 5) << 4: since there are 32 entries in a register of 32 bits

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
28e972b2ea realtek: Configure initial L2 learning setup
Configure a sane L2 learning configuration upon DSA driver load so that the
switch can start learning L2 addresses. Also configure the correct flood masks
for broadcast and unknown unicast traffice.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
9d9bf16aa8 realtek: Add phylink configuration routines for RTL93xx
This adds RTL93xx-specific MAC configuration routines that allow also configuration
of 10GBit links for phylink. There is support for the Realtek-specific HISGMI
protocol.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:06 +02:00
Birger Koblitz
a96b73a890 realtek: Packet Inspection Engine support for RTL930x SoCs
Adds the RTL930x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
2d8d81fe28 realtek: Packet Inspection Engine support for RTL839x SoCs
Adds the RTL839x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
87b3bd07a4 realtek: Packet Inspection Engine support for RTL838x SoCs
Adds the RTL838x-specific PIE support routines.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
54805fc911 realtek: Add driver support for TC offloading
This adds support for offloading TC flower by using the Packet Inspection Engine
of the RTL-SoCs. Basic infrastructure support is provide with callbacks to the
tc subsystem and support for HW packet counters.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
a6678accbd realtek: Add port to smi-bus address mapping
All RTL SoCs addresss PHYs via their port number, which is mapped to an
SMI address. Add support for configuring this mapping via the .dts on all
SoCs apart from the 839x, where the mapping to the 64 ports is fixed.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
2ab4d40293 realtek: Increase maximum RX ring buffer length
Increase the maximum ring buffer length in order to improve
performance on RTL839x devices.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
9eab76c84e realtek: Improve TX CPU-Tag usage
On RTL83xx enable learning of the MAC source address of the CPU port
from outgoing packets. Add documentation on bit fields. On RTL93xx
enable port-mask usage and the use of internal priority, these
SoCs automatically learn the MAC.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
ca04e2dfd0 realtek: Remove storm control and attack warnings
Remove the storm control and attack warnings from the IRQ handler
of the Ethernet driver. There was no consequence to the detection
and the kernel can also handle at least the attacks itself.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Birger Koblitz
e88ac0bbd1 realtek: Correct TX ring size in ethernet driver
This enlarges the size of the TX ring buffer, which prevents warnings
when the buffer runs out of space.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-10-09 08:25:05 +02:00
Paul Fertser
3810e89729 realtek: ensure output drivers are enabled in RTL8231
The bootloader can leave the GPIO expander in a state which doesn't have
output drivers enabled so GPIOs will properly work for input but output
operations will have no effect.

To avoid disrupting the boot in case the bootloader left direction and
data registers in an inconsistent state (e.g. pulling SoC's reset to 0)
reconfigure everything as input.

Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2021-10-02 21:26:12 +02:00
Rui Salvaterra
b4cee3b63f kernel: bump 5.10 to 5.10.70
Deleted (upstreamed):
bcm53xx/patches-5.10/181-Revert-USB-bcma-Add-a-check-for-devm_gpiod_get.patch

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-30 22:29:33 +01:00
Rui Salvaterra
2bf320a5e5 kernel: bump 5.10 to 5.10.69
Patches automatically refreshed.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-09-30 22:29:33 +01:00
INAGAKI Hiroshi
fc050c7b53 realtek: add Kernel 5.10 as testing version
This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in
realtek target to allow using Kernel 5.10 for testing.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
216011e424 realtek: enable uart1 on the devices with PoE support in 5.10
On the devices with PoE support, the secondary UART (uart1) on the SoC
is used to communicate between the SoC and controller.

Enable the secondary UART on the following devices:

- D-Link DGS-1210-10P
- Netgear GS110TPP v1
- Netgear GS310TP v1
- ZyXEL GS1900-8HP v1/v2
- ZyXEL GS1900-10HP
- ZyXEL GS1900-24HP v2

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
45b2a5d840 realtek: use physical addresses in soc dtsi in 5.10
Use physical addresses instead of virtual address in dts files.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
d7b349db7c realtek: use gpio-keys instead of "-polled" if SoC GPIO is used in 5.10
The new backported GPIO driver supports interrupt, so use gpio-keys
instead of gpio-keys-polled for keys connected to the internal GPIO
controller.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
61a3d0075b realtek: update GPIO bindings in the dts files in dts-5.10
this patch includes the following changes:

- adjust mapping for the new driver
  - GPIO 24 -> GPIO 0
  - GPIO 47 -> GPIO 0 (+ disabling system LED)

- disable pins in the invalid range
  (out of the range 0-31 of the new driver)
  - are these pins on the external RTL8231 (&gpio1)?
    - GPIO 67 (-> GPIO 3 on &gpio1?)
    - GPIO 94 (-> GPIO 30 on &gpio1?)

- drop "indirect-access-bus-id" property from gpio0 node in device dts
  files

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
2e676c05dc realtek: fix kernel panic in DSA driver for 5.10
dsa_to_port function in 5.10 returns dsa_port from the port list in
dsa_switch_tree, but the tree is built when the switch is registered
by dsa_register_switch and it's null in rtl83xx_mdio_probe.

So, we need to use dsa_to_port after the registration of the switch.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
99a658cb71 realtek: add pinmux node of LED_GLB_CTRL to rtl838x.dtsi in dts-5.10
This patch adds a pinctrl-single pinmux node to allow disabling system
LED and enabling GPIO 0 (old driver: GPIO 24).

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
a22602728c realtek: fix compile errors in dsa driver for 5.10
this patch fixes the following errors when compiling:

- dsa_switch_alloc is removed[1]

- a parameter "enum dsa_tag_protocol mprot" is added to dsa_tag_protocol
  in dsa_switch_ops (include/net/dsa.h)

- several paramters are added to "phylink_mac_link_up" in dsa_switch_ops
  (include/net/dsa.h)

  added:
    - int speed
    - int duplex
    - bool tx_pause
    - bool rx_pause

- a parameter "struct switchdev_trans *trans" is added to
  port_vlan_filtering in dsa_switch_ops (include/net/dsa.h)

[1]: https://lore.kernel.org/lkml/20191020031941.3805884-17-vivien.didelot@gmail.com/

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
9a4b8d6c30 realtek: fix compile errors in rtl838x_eth.c for 5.10
this patch fixes the following errors when compiling:

- "unsigned int txqueue" is added as an additional parameter of
  ndo_tx_timeout in net_device_ops (include/linux/netdevice.h)

- "mac_link_state" in phylink_mac_ops (include/linux/phylink.h)
  is renamed to "mac_pcs_get_state" and changed the return value
  to void from int

- several parameters are added to "mac_link_up" in phylink_mac_ops
  (include/linux/phylink.h) and the order of the parameters is
  changed

  added:
    - int speed
    - int duplex
    - bool tx_pause
    - bool rx_pause

- a parameter "phy_interface_t *interface" is added to of_get_phy_mode
  (drivers/of/of_net.c) and returns the state instead of phy mode

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:18 +02:00
INAGAKI Hiroshi
3069fffe60 realtek: add "soc" node to soc dtsi in dts-5.10
Add a "soc" node as a simple-bus to rtl838x.dtsi and rtl930x.dtsi.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
ddaeb73de0 realtek: update soc dtsi in 5.10 for backported drivers
this patch updates SoC dtsi (rtl838x.dtsi, rtl930x.dtsi) for the
following backported drivers:

- gpio-realtek-otto (5.13)
- spi-realtek-rtl (5.12)
- irq-realtek-rtl (5.12)

And, disable SoC GPIO node (gpio0) in rtl930x.dtsi in dts-5.10.
Currently, the upstreamed driver doesn't support the GPIO controller on
RTL930x SoC.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
1c020f8b43 realtek: cleanup and update soc dtsi in 5.10
the following changes are included in this patch:

- node is enabled by default, drop 'status = "okay"'
- adjust order of "compatible" lines and "reg" lines
- add a new blank line before fixed-link node in rtl830x.dtsi

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
0de230bd0c realtek: copy dts directory for Kernel 5.10
This patch adds "dts-5.10" directory to use backported drivers.
There are several specification changes in the new drivers, so there
are some compatibility issues in using dts/dtsi files for 5.4.

The old DTS files are moved to "dts-5.4", so their corresponding
kernel version is obvious as well.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[change "dts" to "dts-5.4", adjust Makefile]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
9e418b061c realtek: refresh and update config-5.10
This patch adjusts config-5.10 by running kernel_menuconfig.

Note:

- disable psb6970 phy driver (unused in realtek target?)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
95f089dafe realtek: refresh patches for Kernel 5.10
This patch refresh all patches in patches-5.10/ to adjust for Kernel
5.10.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
46945e02d3 realtek: remove unnecessary line from rtl838x/Platform in 5.10
The following line is already defined in arch/mips/Kbuild.platforms by
300-mips-add-rtl838x-platform.patch.

platform-$(CONFIG_RTL838X) += rtl838x/

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
781f50705c realtek: drop fixup_bigphys_addr from ioremap.h in 5.10
A macro with the same name is provided in asm/pgtable.h in Kernel 5.10,
use it and drop from ioremap.h.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
2ec38bfea1 realtek: fix "help" line in Kconfig in files/patches for 5.10
In Kernel 5.10, "help" must be used instead of "---help---".

this patch fixes the following errors:

drivers/net/dsa/rtl83xx/Kconfig:7: syntax errorgit
drivers/net/dsa/rtl83xx/Kconfig:6: unknown statement "---help---"
drivers/net/dsa/rtl83xx/Kconfig:7:warning: ignoring unsupported character '.'
drivers/net/dsa/rtl83xx/Kconfig:7: unknown statement "This"
drivers/net/ethernet/Kconfig:170: syntax error
drivers/net/ethernet/Kconfig:169: unknown statement "---help---"
drivers/net/ethernet/Kconfig:170:warning: ignoring unsupported character '.'
drivers/net/ethernet/Kconfig:170: unknown statement "Say"
drivers/net/phy/Kconfig:331: syntax error
drivers/net/phy/Kconfig:330: unknown statement "---help---"
drivers/net/phy/Kconfig:331: unknown statement "Supports"

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
2cd00b5147 realtek: backport irq-realtek-rtl driver from 5.12 to 5.10
This patch backports "irq-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
b2bd0199a8 realtek: drop platform irq driver from 5.10
To use backported irq driver, drop old irq driver from realtek target
and call irqchip_init() in setup.c.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
9bac1c20b8 realtek: backport gpio-realtek-otto driver from 5.13 to 5.10
This patch backports "gpio-realtek-otto" driver to Kernel 5.10.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.

Note: GPIO mapping is changed in the upstreamed driver.

  old - new

   24 -  0
   25 -  1
   26 -  2
   27 -  3
   28 -  4
   29 -  5
   30 -  6
   31 -  7
   16 -  8
   17 -  9
   18 - 10
   19 - 11
   20 - 12
   21 - 13
   22 - 14
   23 - 15
    8 - 16
    9 - 17
   10 - 18
   11 - 19
   12 - 20
   13 - 21
   14 - 22
   15 - 23

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
fbd675c668 realtek: drop rtl838x gpio driver from 5.10
To backport the upstreamed driver (gpio-realtek-otto) from 5.13, drop the
old driver from realtek target.

And, modify 301-gpio-add-rtl838x-driver.patch to remove rtl838x GPIO
support and rename it only for rtl8231 GPIO support.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
0b000cbfe0 realtek: backport spi-realtek-rtl driver from 5.12 to 5.10
This patch backports "spi-realtek-rtl" driver to Kernel 5.10 from 5.12.
"MACH_REALTEK_RTL" is used as a platform name in upstream, but "RTL838X"
is used in OpenWrt, so update the dependency by the additional patch.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
1651bd9bc6 realtek: drop rtl838x spi-nor driver from 5.10
To backport the upstreamed driver (spi-realtek-rtl) from 5.12, drop the
old driver from realtek target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-09-26 00:32:17 +02:00
INAGAKI Hiroshi
95170b4350 realtek: copy config/files/patches to 5.10
this patch copies the following files from 5.4 to 5.10:

- config-5.4   -> config-5.10
- files-5.4/   -> files-5.10/
- patches-5.4/ -> patches-5.10/

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rebase on change in files-5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-26 00:32:17 +02:00
Paul Fertser
16ae56b4f9 realtek: fix RTL8231 gpio expander for high GPIOs
GPIOs > 31 require special handling. This patch fixes both the
initialisation and direction get/set operations.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
2021-09-25 19:28:54 +02:00
Soma Zambelly
c5b44af2fc realtek: add ZyXEL GS1900-24HPv2 support
The ZyXEL GS1900-24HPv2 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-24HPv2
* SoC:       Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash:     16 MiB
* RAM:       W631GG8MB-12 128 MiB DDR3 SDRAM
             (stock firmware is configured to use only 64 MiB)
* Ethernet:  24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             24 ethernet port link/activity LEDs (green, SoC controlled)
             24 ethernet port PoE status LEDs
             2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:   1 "RESTORE" button on front panel
             1 "RESET" button on front panel
* Power      120-240V AC C13
* UART:      1 serial header (J41) with populated standard pin connector on
             the left edge of the PCB, angled towards the side.
             The casing has a rectangular cutout on the side that provides
             external access to these pins.
             Pinout (front to back):
             + GND
             + TX
             + RX
             + VCC

Serial connection parameters for both devices: 115200 8N1.

Installation
------------

OEM upgrade method:

(Possible on master once https://patchwork.ozlabs.org/project/openwrt/patch/20210624210408.19248-1-bjorn@mork.no/ is merged)

* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
  flashed to the "Active" partition. If the second option is selected,
  OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
  file by your preferred method to the previously determined partition.
  When prompted, select to boot from the newly flashed image, and reboot the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

U-Boot TFTP method:

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
   > rtk network on
* Since the GS1900-24HPv2 is a dual-partition device, you want to keep the OEM
  firmware on the backup partition for the time being. OpenWrt can only boot
  from the first partition anyway (hardcoded in the DTS). To make sure we are
  manipulating the first partition, issue the following commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
   > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-24hp-v2-initramfs-kernel.bin
   > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
   > sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-24hp-v2-squashfs-sysupgrade.bin
   it may be necessary to restart the network (/etc/init.d/network restart) on
   the running initramfs image.

Signed-off-by: Soma Zambelly <zambelly.soma@gmail.com>
2021-09-13 18:36:15 +02:00
John Audia
02e2723ef3 kernel: bump 5.4 to 5.4.139
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-08-14 20:25:19 +02:00
Daniel Golle
e3096c384c
realtek: fix syntax error introduced by previous commit
A superflus ')' character has slipped into commit 91a52f22a1. Remove it
to fix build.

Fixes: 91a52f22a1 ("treewide: backport support for nvmem on non platform devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-08-05 15:22:26 +01:00
Ansuel Smith
91a52f22a1 treewide: backport support for nvmem on non platform devices
In the current state, nvmem cells are only detected on platform device.
To quickly fix the problem, we register the affected problematic driver
with the of_platform but that is more an hack than a real solution.
Backport from net-next the required patch so that nvmem can work also
with non-platform devices and rework our current patch.
Drop the mediatek and dsa workaround and rework the ath10k patches.
Rework every driver that use the of_get_mac_address api.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
2021-08-05 01:46:26 +02:00
Thomas Nixon
cdb5acac20 Revert "realtek: Fix failsafe mode"
This reverts commit b7ee0786b5.

With the previous commit "realtek: remove rtl83xx vlan 1 special cases"
this is no longer required.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2021-07-25 13:52:38 +02:00
Thomas Nixon
ad712c71ce realtek: remove rtl83xx vlan 1 special cases
On reset, the PVID of all ports is set to 1; if this is reset to 0,
the special cases for VLAN 1 are no longer required.

port_vlan_add is called with vid=0 when the DSA port interfaces are
enabled with no VLAN; previously the VLAN was not configured in this
case, relying on VLAN 1 being present, but with the PVID set to 0,
configuring VLAN 0 as normal works as expected.

Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
2021-07-25 13:52:38 +02:00
Adrian Schmutzler
cce8d16bf1 treewide: call check-size before append-metadata
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.

While at it, do some obvious wrapping improvements.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-07-10 19:40:10 +02:00
Hauke Mehrtens
b7ee0786b5 realtek: Fix failsafe mode
The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is
configured. Do not use the standard failsafe configuration for DSA
accessing the default port directly, but configure a switch on the lan1
interface instead.

This will add the VLAN ID 1 configuration to the switch:
$ bridge vlan show
port              vlan-id
lan1              1 PVID Egress Untagged
switch            1 PVID Egress Untagged

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-06-22 23:23:00 +02:00
Birger Koblitz
76428494c3 realtek: Fix buffer length calculation on RTL8380 with CRC offload
Fixes the buffer and packet length calculations for Ethernet TX on
the RTL8380 SoC when CRC calculation offload is enabled.
CRC-offload is always done by the SoC, but additional CRC
calculation was previously done also by the kernel.
It also fixes detection of the DSA tag for packets on RTL8390
SoCs for ports > 28.

v2 has correct whitespace

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
2021-06-22 23:23:00 +02:00
Rafał Miłecki
4b9a67362d base-files: generate network config with "device" options
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-05-27 10:58:49 +02:00
Birger Koblitz
204956aea5 realtek: Fix VLAN issues introduced by multicast patches
This adds the CPU port to the unknown multicast flooding port mask,
which fixes the VLAN issues introduced by the multicast group patches

Tested-by: Russell Senior <russell@personaltelco.net> [Netgear GS108Tv3]
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no> [whitespace fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz> [unknwon typo fix]
2021-05-09 16:19:31 +02:00
Birger Koblitz
cde31976e3 realtek: Add support for Layer 2 Multicast
Adds support for Layer 2 multicast by implementing the DSA port_mdb_*
callbacks. The Kernel bridge listens to IGMP/MLD messages trapped to
the CPU-port, and calls the Multicast Forwarding Database updates.
The updates manage the L2 forwarding entries and the multicast
port-maps.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
4342d27ec9 realtek: Setup all VLANs with default configurations
This sets up all VLANs with a default configuration on reset:
 - forward based on VLAN-ID and not the FID/MSTI
 - forward based on the inner VLAN-ID (not outer)

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
d4649942ad realtek: Add SoC-specific VLAN setup routine
This adds SoC specific VLAN configuration routines, which
alsoe sets up the portmask table entries that are referred to
in the vlan profiles registers for unknown multicast flooding.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
408990464c realtek: Add support for clause45 PHYs
This adds support for the MMD access registers the RTL-SoCs use to access clause 45
PHYs via mdio.
This new interface is used to add EEE-support for the RTL8226

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
515d9c85f2 realtek: improve EEE support for RTL8380/8390/9300
Clean up and fix bugs in the EEE support for RTL8380/90
Adds EEE support for RTL9300

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
637deabb4a realtek: Add L2 hash bucket size
Adds a hash-bucket size attribute for the different SoCs, in order to
accomodate the buckets with 8 entries of the L2-forwarding tables
on RTL93XX in contrast to only 4 on RTL83XX.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
d497262748 realtek: remove unused FDB print routing
remove fdb_dump debugging function

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
cf4edabefd realtek: add IGMP/MLD snooping support
This adds snooping support for IGMP and MLD on RTL8380/90/9300
by trapping IGMP and MLD packets to the CPU.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
Birger Koblitz
9e8d62e421 realtek: enable CRC offloading
Enables CRC calculation offloading on RTL8380/8390/9300.

Tested on Zyxel XGS1210-10 (RTL9302)/GS1900-48 (RTL8390)/GS1900-10HP (RTL8382)
On the Zyxel GS1900-10HP, an increase of 5% in iperf3 send throughput
and 11% in receive throughput is seen.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-05-07 07:05:16 +02:00
INAGAKI Hiroshi
4c0c860846 realtek: add support for INABA Abaniact AML2-17GP
INABA Abaniact AML2-17GP is a 17 port gigabit switch, based on RTL8382.

Specification:

- SoC		: Realtek RTL8382
- RAM		: DDR3 128 MiB (SK hynix H5TQ1G63EFR)
- Flash		: SPI-NOR 32 MiB (Macronix MX25L25635FZ2I-10G)
- Ethernet	: 10/100/1000 Mbps x17
  - port 1-8	: RTL8218B (SoC)
  - port 8-16	: RTL8218D
  - port wan	: RTL8214FC
- LEDs/Keys	: 1x, 1x
- UART		: pin header on PCB (Molex 530470410 compatible)
  - J14: 3.3V, GND, RX, TX from rear side
  - 115200n8
- Power		: 100-240 VAC, 50/60 Hz, 0.21 A
  - Plug	: IEC 60320-C13

Flash instruction using initramfs image:

1.  Boot AML2-17GP normally
2.  Set the IP address of computer to the range of 192.168.1.0/24, other
    than 192.168.1.248 and connect computer to "WAN/CONSOLE" port of
    AML2-17GP
3.  Access to "http://192.168.1.248" and open firmware setting page

    -- UI Language: 日本語 --
    "メンテナンス" -> "デュアルイメージ"

    -- UI Language: ENGLISH --
    "Maintenance" -> "Dual Image"

4.  Check "イメージ情報 (en: "Images Information")" and set the first
    image to active by choosing "アクティブイメージ" (en: "Active
    Image") in the partition "0"
5.  open firmware upgrade page

    -- UI Language: 日本語 --
    "メンテナンス" -> "アップグレードマネージャー"

    -- UI Language: ENGLISH --
    "Maintenance" -> "Upgrade Manager"

6.  Set the properties as follows

    -- UI Language: 日本語 --
    "アップグレード方式"	: "HTTP"
    "アップグレードタイプ"	: "イメージ"
    "イメージ"			: "アクティブ"
    "ブラウズファイル"		: (select the OpenWrt initramfs image)

    -- UI Language: ENGLISH --
    "Upgrade Method"		: "HTTP"
    "Upgrade Type"		: "Image"
    "Image"			: "(Active)"
    "Browse file"		: (select the OpenWrt initramfs image)

7.  Press "アップグレード" (en: "Upgrade") button and perform upgrade
8.  Wait ~150 seconds to complete flashing
9.  After the flashing, the following message is showed and press "OK"
    button to reboot

    -- UI Language: 日本語 --
    "成功!! 今すぐリブートしますか?"

    -- UI Language: ENGLISH --
    "Success!! Do you want to reboot now?"

10. After the rebooting, reconnect the cable to other port (1-16) and
    open the SSH connection, download the sysupgrade image to the device
    and perform sysupgrade with it
11. Wait ~120 seconds to complete sysupgrade

Note:

- The uploaded image via WebUI will only be written with the length
  embedded in the uImage header. If the sysupgrade image is specified,
  only the kernel is flashed and lacks the rootfs, this causes a kernel
  panic while booting and bootloops.
  To avoid this issue, initramfs image is required for flashing on WebUI
  of stock firmware.

- This device has 1x LED named as "POWER", but it's not connected to the
  GPIO of SoC and cannot be controlled.

- port 17 is named as "WAN/CONSOLE". This port is for the upstream
  connection and console access (telnet/WebUI) on stock firmware.

Back to stock firmware:

1. Set "bootpartition" variable in u-boot-env2 partition to "1" by
   fw_setsys

   fw_setsys bootpartition 1

2. Reboot AML2-17GP

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-05-07 07:05:16 +02:00
Raylynn Knight
c829bc1f2c realtek: Add support for Netgear S350 series switches GS308T and GS310TP
The Netgear GS308T v1 is an 8 port gigabit switch.  The GS310TP v1 is an 8
port POE+ gigabit switch with 2 SFP Ports (currently untested).

The GS308T v1 and GS310TP v1 are quite similar to the Netgear GS1xx
devices already supported.  Theses two devices use the same Netgear
firmware and are very similar to there corresponding GS1xx devices. For
this reason they share a large portion of the device tree with the GS108T
and GS110TP with exception of the uimage magic and model and compatible
values.

All of the above feature a dual firmware layout, referred to as Image0
and Image1 in the Netgear firmware.

In order to manipulate the PoE+ on the GS310TP v1 , one needs the
rtl83xx-poe package

Specifications (GS308T)
----------------------

 * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
 * 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ)
 * RTL8231 GPIO extender to control the LEDs and the reset button
 * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B)
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
 * Power is supplied via a 12V 1A barrel connector

Specifications (GS310TP)
----------------------

 * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
 * Nuvoton M0516LDN for controlling PoE
 * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
 * 32MB 3v NOR SPI Flash (Winbond W25Q256JVFQ)
 * RTL8231 GPIO extender to control the LEDs and the reset button
 * 8 x 10/100/1000BASE-T PoE+ ports, 2 x Gigabit SFP ports,
 internal PHY (RTL8218B)
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
 * Power is supplied via a 54V 1.25A barrel connector

Both devices have UART pinout
-----------

J1 | [o]ooo
      ^ ||`------ GND
      | |`------- RX         [TX out of the serial adapter]
      | `-------- TX         [RX into the serial adapter]
      `---------- Vcc (3V3)  [the square pin]

The through holes are filled with PB-free solder which melts at 375C.
They can also be drilled using a 0.9mm bit.

Installation
------------
Instructions are identical to those for the similar Negear devices
and apply both to the GS308T v1 and GS310TP v1 as well.
-------------------
Boot initramfs image from U-Boot
--------------------------------

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Init network with `rtk network on` command
 3. Load image with `tftpboot 0x8f000000
openwrt-realtek-generic-netgear_gs308t-v1-initramfs-kernel.bin` command
 4. Boot the image with `bootm` command

The switch defaults to IP 192.168.1.1 and tries to fetch the image via
TFTP from 192.168.1.111.

Updating the installed firmware
-------------------------------

The OpenWRT ramdisk image can be flashed directly from the Netgear UI.
The Image0 slot should be used in order to enable sysupgrade.

As with similar switches, changing the active boot partition can be
accomplished in U-Boot as follows:

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Run `setsys bootpartition {0|1}` to select the boot partition
 3. Run `savesys` followed by `boota` to proceed with the boot process

Signed-off-by: Raylynn Knight <rayknight@me.com>
2021-05-07 07:05:16 +02:00
John Audia
daa5860827 kernel: bump 5.4 to 5.4.116
All patches automatically rebased.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-05-07 07:05:16 +02:00
Rui Salvaterra
3326b5e75c treewide: switch the timer frequency to 100 Hz
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:10 +01:00
Bjørn Mork
11d24ffe96 realtek: allow writing to "u-boot-env2"
U-Boot uses the "bootpartition" variable stored in
"u-boot-env2" to select the active system partition. Allow
updates to enable system switching from OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-04-08 09:20:59 +02:00
Stijn Segers
1601b39b61 realtek: rename partitions in Netgear DTSI
Switch the Netgear DTSI for the Realtek target from the OEM partition
naming scheme to accepted OpenWrt naming practices. A quick git grep for
'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas
grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-04-03 18:57:13 +02:00
Adrian Schmutzler
851dadc257 realtek: add ZYXEL_VERS to DEVICE_VARS
Otherwise, the last defined value will be set for all devices.

Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-22 20:58:16 +01:00
Bjørn Mork
963b2ae702 realtek: enable SerDes NWAY and SGMII negotiation
This allows copper SFPs to negotiate speeds lower than 1gig.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
07bf5aaa4c realtek: enabled Marvell and Realtek PHYs
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.

1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
2a912fb63a realtek: enable HWMON for SFP sensors
This adds SFP sensors as a hwmon device, allowing readout of
temperatures, DOM and other sensor readings available from the
SFP.  Example from a ZyXEL GS1900-10HP with a DOM capable
1000Base-SX SFP:

root@gs1900-10hp:~# grep . /sys/class/hwmon/hwmon0/*
/sys/class/hwmon/hwmon0/curr1_crit:90
/sys/class/hwmon/hwmon0/curr1_crit_alarm:0
/sys/class/hwmon/hwmon0/curr1_input:4
/sys/class/hwmon/hwmon0/curr1_label:bias
/sys/class/hwmon/hwmon0/curr1_lcrit:0
/sys/class/hwmon/hwmon0/curr1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/curr1_max:85
/sys/class/hwmon/hwmon0/curr1_max_alarm:0
/sys/class/hwmon/hwmon0/curr1_min:0
/sys/class/hwmon/hwmon0/curr1_min_alarm:0
/sys/class/hwmon/hwmon0/in0_crit:3795
/sys/class/hwmon/hwmon0/in0_crit_alarm:0
/sys/class/hwmon/hwmon0/in0_input:3317
/sys/class/hwmon/hwmon0/in0_label:VCC
/sys/class/hwmon/hwmon0/in0_lcrit:2805
/sys/class/hwmon/hwmon0/in0_lcrit_alarm:0
/sys/class/hwmon/hwmon0/in0_max:3465
/sys/class/hwmon/hwmon0/in0_max_alarm:0
/sys/class/hwmon/hwmon0/in0_min:3135
/sys/class/hwmon/hwmon0/in0_min_alarm:0
/sys/class/hwmon/hwmon0/name:sfp_p10
/sys/class/hwmon/hwmon0/power1_crit:708
/sys/class/hwmon/hwmon0/power1_crit_alarm:0
/sys/class/hwmon/hwmon0/power1_input:259
/sys/class/hwmon/hwmon0/power1_label:TX_power
/sys/class/hwmon/hwmon0/power1_lcrit:89
/sys/class/hwmon/hwmon0/power1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/power1_max:501
/sys/class/hwmon/hwmon0/power1_max_alarm:0
/sys/class/hwmon/hwmon0/power1_min:126
/sys/class/hwmon/hwmon0/power1_min_alarm:0
/sys/class/hwmon/hwmon0/power2_crit:1259
/sys/class/hwmon/hwmon0/power2_crit_alarm:0
/sys/class/hwmon/hwmon0/power2_input:404
/sys/class/hwmon/hwmon0/power2_label:RX_power
/sys/class/hwmon/hwmon0/power2_lcrit:6
/sys/class/hwmon/hwmon0/power2_lcrit_alarm:0
/sys/class/hwmon/hwmon0/power2_max:794
/sys/class/hwmon/hwmon0/power2_max_alarm:0
/sys/class/hwmon/hwmon0/power2_min:10
/sys/class/hwmon/hwmon0/power2_min_alarm:0
/sys/class/hwmon/hwmon0/temp1_crit:100000
/sys/class/hwmon/hwmon0/temp1_crit_alarm:0
/sys/class/hwmon/hwmon0/temp1_input:22547
/sys/class/hwmon/hwmon0/temp1_label:temperature
/sys/class/hwmon/hwmon0/temp1_lcrit:-50000
/sys/class/hwmon/hwmon0/temp1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/temp1_max:85000
/sys/class/hwmon/hwmon0/temp1_max_alarm:0
/sys/class/hwmon/hwmon0/temp1_min:-40000
/sys/class/hwmon/hwmon0/temp1_min_alarm:0
/sys/class/hwmon/hwmon0/uevent:OF_NAME=sfp-p10
/sys/class/hwmon/hwmon0/uevent:OF_FULLNAME=/sfp-p10
/sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_0=sff,sfp
/sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_N=1

Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
e8d391bd46 realtek: re-enable sfp driver for ZyXEL GS1900-10HP
There is no need to define a static link or a phy for the sfp
ports.  Using phy-mode and managed properties to  describe the
link to the sfp phy.

We have to keep the now unconnected virtual "phys" because the
switch  driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
785d830e88 realtek: need to handle PHY_INTERFACE_MODE_NA for sfps
From the validate docs in include/linux/phylink.h:

 When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
 MAC driver to return all supported link modes.

Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
b8e473d18c realtek: fix link-state interrupt
This bug was the root cause for the failing sfp driver.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Hauke Mehrtens
e6ba970b6e realtek: Add ZyXEL GS1900-8
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-8 v1.2
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             8 ethernet port status LEDs (green, SoC controlled)
* Buttons:   1 on-off glide switch at the back (not configurable)
             1 reset button at the right side, behind the air-vent
               (not configurable)
             1 reset button on front panel (configurable)
* Power      12V 1A barrel connector
* UART:      1 serial header (JP2) with populated standard pin connector on
             the left side of the PCB, towards the back. Pins are labelled:
             + VCC (3.3V)
             + TX (really RX)
             + RX (really TX)
             + GND
             the labelling is done from the usb2serial connector's point of
             view, so RX/ TX are mixed up.

Serial connection parameters for both devices: 115200 8N1.

Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
  image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
  > rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only boot off the first partition anyway (hardcoded in the DTS). To
  make sure we are manipulating the first partition, issue the following
  commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
  > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
  > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
  > sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-14 15:07:30 +01:00
Hauke Mehrtens
c6c8d597e1 realtek: Add generic zyxel_gs1900 image definition
Add a new common device definition for the Zyxel GS1900 line of
switches.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-14 15:03:00 +01:00
Bjørn Mork
ba220ad2fd realtek: drop ethtool log noise
Demote a number of debugging printk's to pr_debug to avoid log
nosie.  Several of these functions are called as a result of
userspace activity.  This can cause a lot of log noise when
userspace does periodic polling.

Most of this could probably be removed completely, but let's
keep it for now since these drivers are still in development.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-03-12 00:46:00 +02:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Jason A. Donenfeld
196f3d586f kernel-5.4: bump to 5.4.102 and refresh patches
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.

This commit involved `update_kernel.sh -v -u 5.4`.

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-03-04 22:06:53 +01:00
Michael Mohr
8cbd6f5117 realtek: add support for Netgear GS108T v3
The Netgear GS108T v3 is an 8 port gigabit switch with PoE-PD support
on port 1.  The two prior versions were built using eCos and are not
currently compatible with OpenWRT.

The GS108T v3 is quite similar to both the GS110TPP v1 and GS110TP v3,
all of which use the same firmware image from Netgear.  For this reason,
the device tree is identical aside from the model and compatible values.

All of the above feature a dual firmware layout, referred to as Image0
and Image1 in the Netgear firmware.

Hardware specification
----------------------

 * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
 * 32MB 3v NOR SPI Flash (Macronix MX25L25635F or Winbond W25Q256JVFIQ)
 * RTL8231 GPIO extender to control the LEDs and the reset button
 * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B)
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
 * Power is supplied via a 12V 1A barrel connector or 802.3af

UART pinout
-----------

J1 | [o]ooo
      ^ ||`------ GND
      | |`------- RX         [TX out of the serial adapter]
      | `-------- TX         [RX into the serial adapter]
      `---------- Vcc (3V3)  [the square pin]

The through holes are filled with PB-free solder which melts at 375C.
They can also be drilled using a 0.9mm bit.

Build configuration
-------------------

 * Target System: Realtek MIPS
 * Target Profile: Netgear GS108T v3
 * Target Images -> ramdisk -> Compression: lzma
 * Disable other target images

Boot initramfs image from U-Boot
--------------------------------

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Init network with `rtk network on` command
 3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs108t-v3-initramfs-kernel.bin` command
 4. Boot the image with `bootm` command

The switch defaults to IP 192.168.1.1 and tries to fetch the image via
TFTP from 192.168.1.111.

Updating the installed firmware
-------------------------------

The OpenWRT ramdisk image can be flashed directly from the Netgear UI.
The Image0 slot should be used in order to enable sysupgrade.

As with similar switches, changing the active boot partition can be
accomplished in U-Boot as follows:

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Run `setsys bootpartition {0|1}` to select the boot partition
 3. Run `savesys` followed by `boota` to proceed with the boot process

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Michael Mohr
9fe90e4e5a realtek: refactor the Netgear GS110TPP v1 device tree
Move most of the GS110TPP v1 device tree into a dtsi so that it can be
shared with the GS108T v3.  Additionally:

  * Use macros to simplify the ethernet and switch definitions
  * Zero-pad the offsets and sizes in the partition map to 8 digits each

The spi-max-frequency value has been changed from 10MHz to 50MHz based
on an analysis of the relevant datasheets.  The current driver doesn't
use this property, as the clock speed is fixed. However, it's required
for this type of DT node, so that's why it's present here.

The firmware partition has been split in half, since this is how the
stock firmware uses it.  This can be used to easily revert to a stock
firmware if one is written to the second image area.

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Michael Mohr
9877393fd1 realtek: add and use netgear_nge for the GS110PP v1
The netgear_nge device will be shared between the GS108T v3 (to be added
in a later commit) and the GS110PP v1.  It also enables LZMA compression
for the ramdisk image.

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Adrian Schmutzler
598b29585e target: use SPDX license identifiers on Makefiles
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:18 +01:00
John Audia
2c35899d81 kernel: bump 5.4 to 5.4.93
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system:       x86_64
Build-tested:       ipq806x/R7800, bcm27xx/bcm2711
Run-tested:         ipq806x/R7800
Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64
Run-tested [*]:     ath79/generic, ipq40xx, octeon, ramips/mt7621

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-29 14:22:09 +01:00
Birger Koblitz
1b1bb6bf19 realtek: add debugfs support for mirroring
This adds debugfs support to monitor mirroring via debugfs

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
6f67c079e6 realtek: add API for the hw tables of RTL83XX/93XX SoCs
Add a table API that has per accss register locking and uses
register description information to handle all table access
through a single set of api calls.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
27029277f9 realtek: add switch driver support for the RTL93XX based switches
Adds support for the RTL9300 and RTL9310 series of switches
with 10GBit per port and up to 56 ports.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
d140b9fc23 realtek: add internal and external SDS/PHYs of RTL9300 devices
This adds support for the internal SerDes of the RTL9300 SoC
and for the RTL8218D and RTL8226B phys found in combination
with this SoC in switches.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
e1bca7c77d realtek: fix RTL8231 gpio expander usage with RTL839X SoC
This fixes the usage of the RTL8231 GPIO extender chip
when used with the RTL839X SoCs. Specifically,
the PHY addresses may be different from 0.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
6aac20bc01 realtek: enable default rate limiting and qos settings
Enable default rate limiting and QoS support. Remove
previous storm control code.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
56ac4fced0 realtek: correct l2 offloading tag handling
Makes sure the DSA trailer information on any L2 offloading done
by the switch is honoured by the bridge layer

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
dc9cc0d3e2 realtek: add QoS and rate control
This adds support for identifying QoS information in packets
and use this and rate control information to submit to multiple
egress queues. The ethernet driver is also made to support
2 egress and up to 32 egress queues.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
4237488cf3 realtek: add dtsi for RTL930X SoCs
Add a default dtsi to support RTL930X SoCs.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
8faffa00cb realtek: add support for the RTL9300 timer
this adds support for the SoC timer of the RTL9300 chips, it
provides 6 independent timer/counters, of which the first one
is used as a clocksource and the second one as event timer.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
03c79ca269 realtek: add support for the RTL8390 and RTL9300 SoC IRQs
This adds support for the RTL8390 and RTL9300 SoCs
it also cleans up unnecessary definitions in mach-rtl83xx.h
and moves definitions relevant for irq routing to irq.h

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
cb39602399 realtek: add detection of RTL930X SoCs and RTL8313 SoC
This adds support to detect RTL930X based SoCs and the RTL9313 SoC.
Tested on Zyxel XGS1210-10 (RTL9302B SoC) and the
Zyxel XS1930-12 (RTL9313 SoC)

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Bjørn Mork
1fb413e657 realtek: build ZyXEL vendor firmware compatible initramfs
Append a device specific version trailer used by the stock
firmware upgrade application to validate firmwares.

The trailer contains a list of ZyXEL firmware version
numbers, which includes a four letter hardware identifier.
The stock web UI requires that the current hardware matches
one of the listed versions, and that the version number is
larger than a model specific minimum value. The minimum
version varies between V1.00 and V2.60 for the currently
known GS1900 models. The number is not used anywhere else
to our knowlege, and has no direct relation to the version
info in the u-image header.  We can therefore use an
arbitrary value larger than V2.60.

The stock firmware upgrade application will only load and
flash the part of the file specified in the u-image header,
regardless of file size.  It can therefore not be used to
flash images with an appended rootfs. There is therefore no
need to include the trailer in other images than the
initramfs. This prevents accidentally bricking by attempts
to flash other images from the stock web UI.

Stock images support all models in the series, listing
all of them in the version trailer.  OpenWrt provide model
specific images.  We therefore only list the single supported
hardware identifier for each image.  This eliminates the risk
of flashing the wrong OpenWrt image from stock web UI.

OpenWrt can be installed from stock firmware in two steps:

   1) flash OpenWrt initramfs image from stock web gui
   2) boot OpenWrt and sysupgrade to a squasfs image

The OpenWrt squashfs image depends on a static partition
map in the DTS.  It can only be installed to the "firmware"
partition.  This partition is labeled "RUNTIME1" in u-boot
and in stock firmware, and is referred to as "image 0" in
the stock flash management tool.  The OpenWrt initramfs
can be installed and run from either partitions. But if
you want to keep stock irmware in the spare system partition,
then you must make sure stock firmware is installed to the
"RUNTIME2" partition referred to as "image 1" in the stock
web UI. And the initial OpenWrt initramfs must be flashed
to "RUNTIME1"/"image 0".

The stock flash management application supports direct
selection of both which partition to flash and which
partition to boot next.  This allows software controlled
"dual-boot" between OpenWrt and stock firmware, without
using console access to u-boot. u-boot use the "bootpartition"
variable stored in the second u-boot environment to select
which of the two system partitions to boot.  This variable
is set by the stock flash management application, by direct
user input.  It can also be set in OpenWrt using e.g

 fw_setsys bootpartition 1

to select "RUNTIME2"/"image 1" as default, assuming a
stock firmware version is installed in that partition.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-24 18:12:34 +01:00
Bjørn Mork
ca4832fcac realtek: use vendor-specific magic for ZyXEL
The stock firmware of the ZyXEL GS1900 series use a non-standard
u-image magic.  This is not enforced by the stock u-boot, which is
why we could boot images with the default magic.  The flash
management application of the stock firmware will however verify
the magic, and refuse any image with another value.

Convert to vendor-specific value to get flash management support
in stock firmware, including the ability to upgrade to OpenWrt
directly from stock web UI.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-24 18:12:34 +01:00
Adrian Schmutzler
f52081bcf9 treewide: provide global default for SUPPORTED_DEVICES
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:

  SUPPORTED_DEVICES := $(subst _,$(comma),$(1))

At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:

  device/image name:  vendor_model
  compatible:         vendor,model

The equal redundant definitions are a symptom of this process.

Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.

This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 12:45:21 +01:00
Bjørn Mork
ff7709d223 kernel: mtdsplit_uimage: replace "netgear, uimage" parser
The "netgear,uimage" parser can be replaced by the generic
parser using device specific openwrt,ih-magic and
openwrt,ih-type properties.

Device tree properties for the following devices have not
been set, as they have been dropped from OpenWrt with the
removal of the ar71xx target:

 FW_MAGIC_WNR2000V1     0x32303031
 FW_MAGIC_WNR2000V4     0x32303034
 FW_MAGIC_WNR1000V2_VC  0x31303030
 FW_MAGIC_WPN824N       0x31313030

Tested-by: Sander Vanheule <sander@svanheule.net>  # WNDR3700v2
Tested-by: Stijn Segers <foss@volatilesystems.org> # WNDR3700v1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
647fdafcc5 kernel: mtdsplit_uimage: replace "allnet, uimage" parser
Convert users to the generic "openwrt,uimage" using device specific
"openwrt,ih-magic" properties, and remove "allnet,uimage".

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
John Audia
4ebec0b3e2 kernel: bump 5.4 to 5.4.87
All modification by update_kernel.sh.

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Compile-tested [*]: ath79/{generic,tiny}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64.
Run-tested [*]:     ramips/mt7621 (DIR-878 A1, R6800, RT-AC57U),
                    octeon (EdgeRouter Lite).

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-08 21:09:17 +01:00
Stijn Segers
c4bfe68c83 realtek: add support for ZyXEL GS1900-8HP v1 and v2
The ZyXEL GS1900-8HP is an 8 port gigabit switch with PoE+ support.
There are two versions on the market (v1 & v2) which share similar
specs (same flash size and flash layout, same RAM size, same PoE+ power
envelope) but have a different case and board layout that they each
share with other GS1900 siblings.

The v1 seems to share its PCB and case with non-PoE GS1900-8; as such,
adding support for the GS1900-8 would probably be trivial. The v2 seems
to share its casing and platform with its already supported bigger
brother, the GS1900-10HP - its board looks the same, except for two
holes where the GS1900-10 has its SFP ports.

Like their 10 port sibling, both devices have a dual firmware layout.
Both GS1900-8HP boards have the same 70W PoE+ power budget. In order to
manipulate the PoE+, one needs the rtl83xx-poe package [1].

After careful consideration it was decided to go with separate images
for each version.

Specifications (v1)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Nanya NT5TU128M8HE-AC 128 MiB DDR2 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59111KMLG (IEEE 802.3at-2009 compliant, 2x)
* UART:      1 serial header with populated standard pin connector on the
             left side of the PCB, towards the bottom. Pins are labeled:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Specifications (v2)
-------------------
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Samsung K4B1G0846G 128 MiB DDR3 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* PoE+:      Broadcom BCM59121B0KMLG (IEEE 802.3at-2009 compliant)
* UART:      1 angled serial header with populated standard pin connector
             accessible from outside through the ventilation slits on the
             side. Pins from top to bottom are clearly marked on the PCB:
             + VCC (3.3V)
             + TX
             + RX
             + GND

Serial connection parameters for both devices: 115200 8N1.

Installation
------------
Instructions are identical to those for the GS1900-10HP and apply both
to the GS1900-8HP v1 and v2 as well.

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
  image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
  > rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only boot off the first partition anyway (hardcoded in the DTS). To
  make sure we are manipulating the first partition, issue the following
  commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
  > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-initramfs-kernel.bin
  > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
  > sysupgrade /tmp//tmp/openwrt-realtek-generic-zyxel_gs1900-8hp-v{1,2}-squashfs-sysupgrade.bin

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[merge PoE case, keep device definitions separate, change all those
hashes in the commit message to something else so they don't get
removed when changing the commit ...]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-08 20:48:22 +01:00
Adrian Schmutzler
40ea2fea4f realtek: remove model prefix from LED label for ZyXEL GS1900
This is used as fixed status LED, so no migration is needed.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-08 20:39:02 +01:00
Stijn Segers
0542cb6a2b realtek: introduce shared DTSI for GS1900 series
The ZyXEL GS1900-8HP v1, v2 and GS1900-10HP are all built on a similar
Realtek RTL8380M platform. Create a common DTSI in preparation for
GS1900-8HP support, and switch to the macros defined in rtl838x.dtsi.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[drop redundant includes, use &mdio directly, do not replace SFP
ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-08 20:39:02 +01:00
Stijn Segers
e1f5ffa48c realtek: ZyXEL: spell as done by manufacturer
ZyXEL spells its own name all uppercase with just the Y lowercase. Adapt
the realtek target to follow this (other OpenWrt targets already do so).

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-01-07 19:51:50 +01:00
Stijn Segers
5bdf50d13b realtek: move memory node to device DTS
Move the memory out of the rtl838x.dtsi and into the device family DTSI
or device DTS if applicable. This aligns with upstream practice.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[add missing block for dgs-1210-10p, move block below chosen node]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-07 19:51:50 +01:00
Adrian Schmutzler
5f958cb21f realtek: remove duplicate '/dts-v1/;' identifier
The identifier is already present in rtl838x.dtsi, and adding it
twice is not only redundant but actually wrong.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-07 19:51:50 +01:00
Stijn Segers
ac16e6b2ea realtek: set PoE power budget for ZyXEL GS1900-10HP
As per the manufacturer's specifications, set the GS1900-10HP PoE power
budget to 77W.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-01-07 19:51:50 +01:00
Birger Koblitz
89f71ebb35 realtek: fix build issues
This fixes the build problems for the REALTEK target by adding a proper
configuration option for the phy module.

Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
2021-01-05 22:43:40 +01:00
Sander Vanheule
f4b687d1f0 realtek: use kernel defined halt
If _machine_hang is not defined on MIPS, the kernel will check if the
CPU can enter a more power efficient sleep mode. Since the realtek
platform supports mips32_r2, this should issue a WAIT instruction
instead of a trivial infinite loop.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2020-12-22 19:11:50 +01:00
Rafał Mikrut
561bfc96f9 realtek: Add missing case in switch statement
Cppcheck shows here duplicated break.

Code `state->speed = SPEED_1000;` will be never executed because above
it there is break statement.

Almost identical statement is placed in another realtek driver
18a53d43d6/target/linux/realtek/files-5.4/drivers/net/dsa/rtl83xx/dsa.c (L286-L294)

Signed-off-by: Rafał Mikrut <mikrutrafal@protonmail.com>
2020-12-11 13:48:24 +01:00
Rafał Mikrut
848d668427 realtek: Fix self assignment
Cppcheck shows self initialization error, which is an obvious bug.

Basing on logic of similar fragment below I assigned to this variable,
value `RTL838X_LED_GLB_CTRL` which I think is proper.

Signed-off-by: Rafał Mikrut <mikrutrafal@protonmail.com>
2020-12-11 13:48:24 +01:00
John Audia
3f165fa7cc kernel: bump 5.4 to 5.4.82
Removed since included upstream and could be reverse-applied by quilt:
  backport-5.4/315-v5.10-usbnet-ipeth-fix-connectivity-with-ios-14.patch

Remaining modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [build/run x86_64]
2020-12-09 17:05:40 +01:00
John Crispin
9aabd934a9 realtek: fix SFP ports on the dlink 10port switch
Signed-off-by: John Crispin <john@phrozen.org>
2020-12-02 10:43:45 +01:00
John Crispin
cfbda66279 realtek: add zyxel_gs1900-10hp support
Signed-off-by: John Crispin <john@phrozen.org>
2020-12-02 07:54:14 +01:00
John Crispin
1dc5d56ca0 realtek: cleanup package selection
Signed-off-by: John Crispin <john@phrozen.org>
2020-12-02 07:53:52 +01:00
John Crispin
9aa4490502 realtek: clean up board.json generation
In this new setup the switch is treated as wan, lan1.100 is used as
our mgmt vlan.

The board mac is applied to eth0, switch and switch.1

The board mac is assigned with the LA bit set to all lan ports while
incrementing it.

Signed-off-by: John Crispin <john@phrozen.org>
2020-12-02 07:53:21 +01:00
Kevin Darbyshire-Bryant
4420ddaa58 kernel: clean up patch fuzz
Recent kernel bumps & target patch refactors have left some patch fuzz
around.  Refreshed kernel patches using update_kernel script.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-11-26 17:32:43 +00:00
John Crispin
2b88563ee5 realtek: update the tree to the latest refactored version
* rename the target to realtek
* add refactored DSA driver
* add latest gpio driver
* lots of arch cleanups
* new irq driver
* additional boards

Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: John Crispin <john@phrozen.org>
2020-11-26 13:29:27 +01:00