Commit Graph

27087 Commits

Author SHA1 Message Date
Felix Fietkau
e410833bdd kernel: add a locking fix for netfilter hardware flow offloading
Protect the flow block cb list readers against concurrent updates

Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 20:44:01 +01:00
Felix Fietkau
9b482ee22f kernel: add more fixes for mtk_eth_soc
Fix corner cases in DSA offload
Add refcounting fix for flow offload
Fix VLAN untagging issue on MT7986

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 11:47:36 +01:00
Maxim Anisimov
21762e4653 ramips: add support for Keenetic KN-3010
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.

Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
   to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2022-11-20 16:44:24 +01:00
Xiaopo Zhang
a28297d395 x86: enable PINCTRL for all Intel platform
Enable Intel PINCTRL for all platform on both 32 bit and 64 bit target.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Xiaopo Zhang
34615250a9 x86/64: enable Intel PINCTRL in 64bit target
Intel PINCTRL is not enable in the 64bit build, while it is enabled in
the x86/general target, which disables the ability of controlling GPIO
in the 64 bit build.

This commit copies the corresponding part of x86/general config, since
it is already there, so it should be fine to enable the same settings
here.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Will Moss
288b0004bf ath79: fix MAC address assigment for TP-Link TL-WR740N/TL-WR741ND v4
On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main
device MAC address, so do not increment it. WAN MAC is LAN MAC + 1.

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-20 16:30:27 +01:00
Roger Pueyo Centelles
5a1d7d8c1b ath79: disable image building for Ubiquiti EdgeSwitch 8XP
The downstream OpenWrt driver for the BCM53128 switch ceased to work,
rendering the 8 LAN ports of the device unusable. This commit disables
image building while the problem is being solved.

See issue #10374 for more details.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2022-11-20 16:24:24 +01:00
Edward Chow
3d343ca713 ath79: calibrate nand netgear wndrxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my wndr3700v4 and wndr4500v3.
Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-20 16:13:48 +01:00
Aleksander Jan Bajkowski
bca663f20f kernel: backport tso for asix driver
Performance comparison (iperf3, mtu 1500):
Before: 53.9 Mbps
After: 87.9 Mbps

The tests were performed on a BT Home Hub 5A router.
The iperf3 server was running on the router, the client
on the host.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Christian Buschau
084c20f6c5 lantiq: xway: kernel: enable SMP support
Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT.

Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421.

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
d3527bb83b lantiq: xway: ar9: add ICU1 (2nd core for SMP)
Fixes leftover TODO from commit 6bf179b270

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
fb0256e88e lantiq: xway: refresh kernel config
Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget'

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Edward Chow
e354b01baf ath79: calibrate all ar9344 tl-WDRxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my tplink tl-wdr4310.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
224babfd6f mediatek: mt7623: disable swconfig
The mt7623 subtarget supports 2 devices:
 * Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
 * UniElec U7623-02 (added in 4def81f30f).

Both devices support DSA from the beginning, thus
swconfig can be safely disabled.

In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
0e001e4185 mediatek: mt7623: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Moritz Warning
dc7d431b60 treewide: uniform vendor name for devolo
The company name is lower case on the website
(https://www.devolo.de) and in product names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-18 20:27:52 +01:00
Moritz Warning
c0fb12c42e treewide: uniform vendor name for ASUS
Their own website (https://www.asus.com)
always uses the upper case style name.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-16 23:30:11 +01:00
Josef Schlehofer
941132cb3c mpc85xx: fix missing kernel config symbol
While compiling OpenWrt master for Turris 1.x routers (p2020), it
reported following error:

    Gianfar Ethernet (GIANFAR) [Y/n/m/?] y
    Freescale DPAA2 Ethernet Switch (FSL_DPAA2_SWITCH) [N/m/y/?] (NEW)
Error in reading or end of file.

Let's fix it by disabling it.

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-11-16 23:30:11 +01:00
John Audia
9e137bb10e kernel: bump 5.10 to 5.10.155
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-16 23:30:11 +01:00
John Audia
170f3d7b0a kernel: bump 5.15 to 5.15.79
All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/mt7621
Run-tested: bcm2711/RPi4B, ramips/mt7621

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-16 23:30:11 +01:00
Kuan-Yi Li
49bbfd9968 cypress-nvram: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
c6e86d8095 linux-firmware: broadcom: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
22fd8b0df6 cypress-nvram: disassociate from external source repo
Since all NVRAM files in external repo are now upstreamed and to lower
future maintenance cost, disassociate the package from external source
repo.

All upstream pending NVRAM files shall be stored locally from now on.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[Remove outdated URL, add SPDX-License-Identifier]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-16 20:14:13 +01:00
Pawel Dembicki
f74275c936 kernel: add missing symbol in generic config
Found during work on qoriq target.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[improve commit message, remove from target configs]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-11-16 20:23:34 +02:00
Kuan-Yi Li
a110418027 linux-firmware: offer two versions of firmware for CYW4339
According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works
only with firmware from `linux-firmware`. However, firmware from
`cypress-firmware` suite is directly from the chip company (Infineon) and
is actually newer.

Instead of dropping the firmware from Infineon, create a package named
`brcmfmac-firmware-4339-sdio`, and keep the Infineon version of
`cypress-firmware-4339-sdio` around.

This gives us devs the option to choose. Also, it means that

 - packages `brcmfmac-firmware-*` uniformly come from `linux-firmware`
 - packages `cypress-firmware-*` uniformly come from `cypress-firmware`

so hopefully brings more clarity.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:49:58 +01:00
Kuan-Yi Li
729cdff71d bcm27xx: switch to linux-firmware SDIO NVRAM
Package `cypress-nvram` was added because back then the files for newer
RPi models on `linux-firmware` didn't have the proper values.

It is the other way around nowadays, so switch back to `linux-firmware`.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:48:54 +01:00
Kuan-Yi Li
efaad5e901 cypress-nvram: use symlink to provide NVRAM for some RPis
This is to align the implementation with upstream `linux-firmware`.

Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware`
source repository, their NVRAM is provided through a symbolic link to
NVRAM of another board with an identical wireless design.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:47:54 +01:00
Chuanhong Guo
c984fc7624
rockchip: use LZMA FIT for kernel image
Use LZMA compressed kernel to save some space in boot partition.

Fixes: #11197
Tested-by: Tianling Shen <cnsztl@immortalwrt.org> [NanoPi R2S]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-11-14 22:50:21 +08:00
Lech Perczak
6fdeb48c1e ath79: support Ruckus ZoneFlex 7025
Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise
access point with built-in Ethernet switch, in an electrical outlet form factor.

Hardware highligts:
- CPU: Atheros AR7240 SoC at 400 MHz
- RAM: 64MB DDR2
- Flash: 16MB SPI-NOR
- Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio
- Ethernet: single Fast Ethernet port inside the electrical enclosure,
  coupled with internal LSA connector for direct wiring,
  four external Fast Ethernet ports on the lower side of the device.
- PoE: 802.3af PD input inside the electrical box.
  802.3af PSE output on the LAN4 port, capable of sourcing
  class 0 or class 2 devices, depending on power supply capacity.
- External 8P8C pass-through connectors on the back and right side of the device
- Standalone 48V power input on the side, through 2/1mm micro DC barrel jack

Serial console: 115200-8-N-1 on internal JP1 header.
Pinout:

---------- JP1
|5|4|3|2|1|
----------

Pin 1 is near the "H1" marking.
1 - RX
2 - n/c
3 - VCC (3.3V)
4 - GND
5 - TX

Installation:
There are two methods of installation:
- Using serial console [1] - requires some disassembly, 3.3V USB-Serial
  adapter, TFTP server,  and removing a single T10 screw,
  but with much less manual steps, and is generally recommended, being
  safer.
- Using stock firmware root shell exploit, SSH and TFTP [2]. Does not
  work on some rare versions of stock firmware. A more involved, and
  requires installing `mkenvimage` from u-boot-tools package if you
  choose to rebuild your own environment, but can be used without
  disassembly or removal from installation point, if you have the
  credentials.
  If for some reason, size of your sysupgrade image exceeds 13312kB,
  proceed with method [1]. For official images this is not likely to
  happen ever.

[1] Using serial console:
0. Connect serial console to H1 header. Ensure the serial converter
   does not back-power the board, otherwise it will fail to boot.

1. Power-on the board. Then quickly connect serial converter to PC and
   hit Ctrl+C in the terminal to break boot sequence. If you're lucky,
   you'll enter U-boot shell. Then skip to point 3.
   Connection parameters are 115200-8-N-1.

2. Allow the board to boot.  Press the reset button, so the board
   reboots into U-boot again and go back to point 1.

3. Set the "bootcmd" variable to disable the dual-boot feature of the
   system and ensure that uImage is loaded. This is critical step, and
   needs to be done only on initial installation.

   > setenv bootcmd "bootm 0x9f040000"
   > saveenv

4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed:

   > setenv serverip 192.168.1.2
   > setenv ipaddr 192.168.1.1
   > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin
   > bootm 0x81000000

5. Optional, but highly recommended: back up contents of "firmware" partition:

   $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin

6. Copy over sysupgrade image, and perform actual installation. OpenWrt
   shall boot from flash afterwards:

   $ ssh root@192.168.1.1
   # sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin

[2] Using stock root shell:
0. Reset the device to factory defaullts. Power-on the device and after
   it boots, hold the reset button near Ethernet connectors for 5
   seconds.

1. Connect the device to the network. It will acquire address over DHCP,
   so either find its address using list of DHCP leases by looking for
   label MAC address, or try finding it by scanning for SSH port:

   $ nmap 10.42.0.0/24 -p22

   From now on, we assume your computer has address 10.42.0.1 and the device
   has address 10.42.0.254.

2. Set up a TFTP server on your computer. We assume that TFTP server
   root is at /srv/tftp.

3. Obtain root shell. Connect to the device over SSH. The SSHD ond the
   frmware is pretty ancient and requires enabling HMAC-MD5.

   $ ssh 10.42.0.254 \
   -o UserKnownHostsFile=/dev/null \
   -o StrictHostKeyCheking=no \
   -o MACs=hmac-md5

   Login. User is "super", password is "sp-admin".
   Now execute a hidden command:

   Ruckus

   It is case-sensitive. Copy and paste the following string,
   including quotes. There will be no output on the console for that.

   ";/bin/sh;"

   Hit "enter". The AP will respond with:

   grrrr
   OK

   Now execute another hidden command:

   !v54!

   At "What's your chow?" prompt just hit "enter".
   Congratulations, you should now be dropped to Busybox shell with root
   permissions.

4. Optional, but highly recommended: backup the flash contents before
   installation. At your PC ensure the device can write the firmware
   over TFTP:

   $ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin
   $ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin

   Locate partitions for primary and secondary firmware image.
   NEVER blindly copy over MTD nodes, because MTD indices change
   depending on the currently active firmware, and all partitions are
   writable!

   # grep rcks_wlan /proc/mtd

   Copy over both images using TFTP, this will be useful in case you'd
   like to return to stock FW in future. Make sure to backup both, as
   OpenWrt uses bot firmwre partitions for storage!

   # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1
   # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1

   When the command finishes, copy over the dump to a safe place for
   storage.

   $ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/

5. Ensure the system is running from the BACKUP image, i.e. from
   rcks_wlan.bkup partition or "image 2". Otherwise the installation
   WILL fail, and you will need to access mtd0 device to write image
   which risks overwriting the bootloader, and so is not covered here
   and not supported.

   Switching to backup firmware can be achieved by executing a few
   consecutive reboots of the device, or by updating the stock firmware. The
   system will boot from the image it was not running from previously.
   Stock firmware available to update was conveniently dumped in point 4 :-)

6. Prepare U-boot environment image.
   Install u-boot-tools package. Alternatively, if you build your own
   images, OpenWrt provides mkenvimage in host staging directory as well.
   It is recommended to extract environment from the device, and modify
   it, rather then relying on defaults:

   $ sudo touch /srv/tftp/u-boot-env.bin
   $ sudo chmod 666 /srv/tftp/u-boot-env.bin

   On the device, find the MTD partition on which environment resides.
   Beware, it may change depending on currently active firmware image!

   # grep u-boot-env /proc/mtd

   Now, copy over the partition

   # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1

   Store the stock environment in a safe place:

   $ cp /srv/tftp/u-boot-env.bin ~/

   Extract the values from the dump:

   $ strings u-boot-env.bin | tee u-boot-env.txt

   Now clean up the debris at the end of output, you should end up with
   each variable defined once. After that, set the bootcmd variable like
   this:

   bootcmd=bootm 0x9f040000

   You should end up with something like this:

bootcmd=bootm 0x9f040000
bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env)
mtdids=nor0=ar7100-nor0
bootdelay=2
filesize=52e000
fileaddr=81000000
ethact=eth0
stdin=serial
stdout=serial
stderr=serial
partition=nor0,0
mtddevnum=0
mtddevname=u-boot
ipaddr=192.168.0.1
serverip=192.168.0.2
stderr=serial
ethact=eth0

   These are the defaults, you can use most likely just this as input to
   mkenvimage.

   Now, create environment image and copy it over to TFTP root:

   $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt
   $ sudo cp u-boot-env.bin /srv/tftp

   This is the same image, gzipped and base64-encoded:
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7. Perform actual installation. Copy over OpenWrt sysupgrade image to
   TFTP root:

   $ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp

   Now load both to the device over TFTP:

   # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1
   # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1

   Verify checksums of both images to ensure the transfer over TFTP
   was completed:

   # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin

   And compare it against source images:

   $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin

   Locate MTD partition of the primary image:

   # grep rcks_wlan.main /proc/mtd

   Now, write the images in place. Write U-boot environment last, so
   unit still can boot from backup image, should power failure occur during
   this. Replace MTD placeholders with real MTD nodes:

   # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd>
   # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd>

   Finally, reboot the device. The device should directly boot into
   OpenWrt. Look for the characteristic power LED blinking pattern.

   # reboot -f

   After unit boots, it should be available at the usual 192.168.1.1/24.

Return to factory firmware:

1. Boot into OpenWrt initramfs as for initial installation. To do that
   without disassembly, you can write an initramfs image to the device
   using 'sysupgrade -F' first.
2. Unset the "bootcmd" variable:
   fw_setenv bootcmd ""
3. Concatenate the firmware backups, if you took them during installation using method 2:

   $ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin

3. Write factory images downloaded from manufacturer website into
   fwconcat0 and fwconcat1 MTD partitions, or restore backup you took
   before installation:

   # mtd write ruckus_zf7025_backup.bin /dev/mtd1

4. Reboot the system, it should load into factory firmware again.

Quirks and known issues:
- Flash layout is changed from the factory, to use both firmware image
  partitions for storage using mtd-concat, and uImage format is used to
  actually boot the system, which rules out the dual-boot capability.
- The 2.4 GHz radio has its own EEPROM on board, not connected to CPU.
- The stock firmware has dual-boot capability, which is not supported in
  OpenWrt by choice.
  It is controlled by data in the top 64kB of RAM which is unmapped,
  to avoid   the interference in the boot process and accidental
  switch to the inactive image, although boot script presence in
  form of "bootcmd" variable should prevent this entirely.
- On some versions of stock firmware, it is possible to obtain root shell,
  however not much is available in terms of debugging facitilies.
  1. Login to the rkscli
  2. Execute hidden command "Ruckus"
  3. Copy and paste ";/bin/sh;" including quotes. This is required only
     once, the payload will be stored in writable filesystem.
  4. Execute hidden command "!v54!". Press Enter leaving empty reply for
     "What's your chow?" prompt.
  5. Busybox shell shall open.
  Source: https://alephsecurity.com/vulns/aleph-2019014

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-11-13 22:36:06 +01:00
Ivaylo Ivanov
6afc355b2e ramips: Add support for D-Link DIR-3060 A1
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset

Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:

    Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
    Give it ~30 seconds, to boot the recovery mode GUI
    Connect your client computer to LAN1 of the device
    Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
    Call the recovery page for the device at http://192.168.0.1/
    Use the provided emergency web GUI to upload and flash a new firmware to the device

Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
2022-11-13 22:36:06 +01:00
Daniel Fuchs
794d1645b3 ramips: add support for Amped Wireless B1200EX
This device is almost identical to the already supported Edimax
EW-7476RP5, the only differences are:
- There is no mode selection slider switch on this device
- The two wireless LEDs are green instead of blue
- Model name in the CSYS header is RN10

Additional changes:
- Moved WiFi LEDs and the slider switch to the individual dt files
- Added ieee80211-freq-limit to the mt7612e radio to properly disable
  2.4GHz band on this radio

Device specifications:
SoC:	MediaTek MT7620a @ 580MHz
RAM:	64M (Winbond W9751G6KB-25)
FLASH:	8MB (Macronix)
WiFi:	SoC-integrated: MediaTek MT7620a bgn
WiFi:	MediaTek MT7612EN nac
GbE:	1x (RTL8211E)
BTN:	WPS/RESET
LED:	- WiFi 5G (green)
	- WiFi 2.4G (green)
	- Signal Strength (green)
	- Power (green)
	- WPS (green)
	- LAN (green)
UART:	UART is present as Pads with throughholes on the PCB. They are
	located next to the WPS button
	3.3V - RX - GND - TX / 57600-8N1
	3.3V is the square pad

Installation:
Upload the sysupgrade image via the default web interface

Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
2022-11-13 22:36:06 +01:00
Mikhail Zhilkin
0cfd15552e ramips: add support for Rostelecom RT-SF-1
Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm
company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 256 MiB, Micron MT29F2G08ABAGA3W
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1xUSB3.0
ZigBee: 3.0, EFR32 MG1B232GG
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1. Remove dots from the OpenWrt factory image filename
2. Login to the router web interface
3. Update firmware using web interface with the OpenWrt factory image
4. If OpenWrt is booted, then no further steps are required. Enjoy!
   Otherwise (Stock firmware has booted again) proceed to the next step.
5. Update firmware using web interface with any version of the Stock
   firmware
6. Update firmware using web interface with the OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
    printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+------------+
| use | address    | example    |
+-----+------------+------------+
| LAN | label      | *:72, *:d2 |
| WAN | label + 11 | *:7d, *:dd |
| 2g  | label + 2  | *:74, *:d4 |
| 5g  | label + 3  | *:75, *:d5 |
+-----+------------+------------+
The label MAC address was found in Factory 0x21000

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-13 21:51:22 +01:00
Mikhail Zhilkin
e6b99a4e43 ramips: create common dtsi for Sercomm Dxx routers
This commit adds common dtsi for the following Sercomm devices with 256
MB NAND:
Beeline Smartbox TURBO (Sercomm DF3)
Rostelecom RT-SF-1 (Sercomm DKG)

Also fixed typo ("Container" mtd name should be with a capital).

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-11-13 21:51:22 +01:00
Martin Dziura
a0b25e17ae ramips: glinet_gl-mt300n-v2: allow to use I2C and UART1 pins as GPIO
This is explicitly intended by the official documentation at
https://docs.gl-inet.com/en/3/specification/gl-mt300n-v2/#pcb-pinout

Signed-off-by: Martin Dziura <m.dziura@tum.de>
2022-11-13 21:51:22 +01:00
David Bauer
fdcd383919 kconfig: abort configuration on unset symbol
This fixes the initial patch to cover all cases where unset symbols are
handled in the code.

Fixes commit eaa9c94c75 ("generic: Kconfig: exit on unset symbol")

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-11-13 16:49:30 +01:00
Lech Perczak
1a49b499f1 ipq40xx: dts: remove leftover nodes after DSA conversion
Remove ess-psgmii@98000, edma@c080000 and ess-switch@c000000 nodes.
These nodes are not used after the DSA conversion, but were left over
in a few devices added recently.

ZTE MF289F is omitted on purpose, as for it, these nodes will be removed
together with DSA conversion.

Build tested only, as I only have MF286D from those devices.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2022-11-13 15:31:54 +01:00
Sven Eckelmann
fc69532eb9 ipq40xx: Convert plasmacloud,pa2200 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"
  - can be used to power the device

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 2" port was used in the past
for "WAN" functionality in OpenWrt.

Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
ce6c9e0328 ipq40xx: utilize nvmem-cells for plasmacloud,pa2200
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
539a5fd624 ipq40xx: Convert plasmacloud,pa1200 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"
  - can be used to power the device

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 2" port was used in the past
for "WAN" functionality in OpenWrt.

Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Sven Eckelmann
b8bda645fc ipq40xx: utilize nvmem-cells for plasmacloud,pa1200
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-13 15:26:34 +01:00
Arne Zachlod
364550f9d9 ramips: fix MAC address assignment for rt1800, e7350
previous commit ffa4b5283b introduced a bug which broke the MAC address
assignment for belkin,rt1800 and linksys,e7350.

Fixes: ffa4b5283b ("ramips: add support for Mikrotik LtAP-2HnD")
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2022-11-13 15:17:49 +01:00
Hauke Mehrtens
b97e5ac785 bcm4908: Refresh kernel patches
Refresh the kernel patches for this target. No manual changes.

Fixes: 45ac906c64 ("bcm4908: update DTS files with the latest changes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-11-12 22:53:04 +01:00
Sven Eckelmann
087a8e39be ipq40xx: utilize nvmem-cells for openmesh,a62
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
2b2f14c959 ipq40xx: utilize nvmem-cells for openmesh,a42
The calibration data and mac addresses on this device are stored in the
0:ART partition. It is therefore possible to move the code to handle them
directly to the devicetree instead of the various scripts.

But the actual relevant information about the partition layout is provided
by the bootloader via bootargs (mtdparts) and not via the devicetree
itself. Instead of using a fixed-partition template, the mtd dynamic
partitions support from the upstream kernel is used.

Reported-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
c6bef1b83a ipq40xx: Convert openmesh,a62 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - can be used to power the device
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 1" port was used in the past
for "WAN" functionality in OpenWrt.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Tested-by: Michaël BILCOT <michael.bilcot@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Sven Eckelmann
66a3c32b47 ipq40xx: Convert openmesh,a42 to DSA
* ethernet1:

  - physical port label "Ethernet 1"
  - can be used to power the device
  - its mac address is printed on the device label

* ethernet2:

  - physical port label "Ethernet 2"

Both ports are not marked by there role (because the vendor firmware
automatically detects roles) but the "Ethernet 1" port was used in the past
for "WAN" functionality in OpenWrt.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2022-11-12 18:15:55 +01:00
Guillaume Lefebvre
65d9a715fc ipq40xx: D-Link DAP-2610: convert to DSA
Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
2022-11-12 18:15:55 +01:00
Óscar García Amor
62efb34071 ramips: add support for Cudy WR1300 v2
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7613BE
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Ports: 1 USB 3.0
 - Buttons: Reset, WPS
 - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
 - Power: DC 12V 1A tip positive

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
18801f2648 ramips: mt7621: use seama-lzma-loader for D-Link DIR-860L B1
Fix the LZMA ERROR 1 with a single line of recipe instead of duplicating
"uimage-lzma-loader".

While reviewing my original submission of commit ce19571004 David
suggested to use $(Device/uimage-lzma-loader), but due to the specific
needs of the vendor bootloader that simple oneliner didn't work.

The new $(Device/seama-lzma-loader) is for those SEAMA capable
bootloaders.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
c293b492df ramips: rt3883: use seama-lzma-loader for D-Link DIR-645
In the support topic [0] of the GitHub issue #10634 it was found out
(based on boot logs) that the uimage-lzma-loader (commit 09faa73c53)
never worked, as an earlier workaround (commit 6fba88de19) negated
the recipe:

    3: System Boot system code via Flash.
    ## Booting image at bc050000 ...
    raspi_read: from:50000 len:40
    .raspi_read: from:50000 len:c
    .raspi_read: from:50000 len:1fa000
    ................................We have SEAMA, Image Size = 2072512
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK
    ## Transferring control to Linux (at address 80000000) ...
    ## Giving linux memsize in MB, 64

    Starting kernel ...

    [    0.000000] Linux version 5.4.188 (builder@buildhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
    [    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
    [    0.000000] printk: bootconsolde [early0] enabled
    [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
    [    0.000000] MIPS: machine is D-Link DIR-645
    [    0.000000] Initrd not found or empty - disabling initrd

Using the new seama-lzma-loader it's able to boot OpenWrt 22.03
and OpenWrt SNAPSHOT too:

    3: System Boot system code via Flash.
    ## Booting image at bc050000 ...
    raspi_read: from:50000 len:40
    .raspi_read: from:50000 len:c
    .raspi_read: from:50000 len:48b004
    .........................................................................We have SEAMA, Image Size = 4763588
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK
    ## Transferring control to Linux (at address 80000000) ...
    ## Giving linux memsize in MB, 64

    Starting kernel ...

    OpenWrt kernel loader for MIPS based SoC
    Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
    Decompressing kernel... done!
    Starting kernel at 80000000...

    [    0.000000] Linux version 5.10.144 (xabolcs@ut2004) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20774+2-b71affaf8b) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Sep 27 23:02:30 2022
    [    0.000000] SoC Type: Ralink RT3883 ver:1 eco:5
    [    0.000000] printk: bootconsole [early0] enabled
    [    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
    [    0.000000] MIPS: machine is D-Link DIR-645
    [    0.000000] Initrd not found or empty - disabling initrd
    [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
    [    0.000000] Zone ranges:
    [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Movable zone start for each node
    [    0.000000] Early memory node ranges
    [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
    [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256
    [    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2

The OKLI Loader is unable to read the flash on this SoC:

    Looking for OpenWrt image... not found! ('0xddbaddba' at 0xbc051000)

0: https://forum.openwrt.org/t/136435

Fixes: GitHub issue #10634 ("V22.03.0 release currently does not work on D-Link DIR-645")
Fixes: 09faa73c53 ("ramips: rt3883: use lzma-loader for DIR-645")
Tested-by: Glenn Fowler <gfowler1@outlook.com>
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Szabolcs Hubai
e7ad68d682 ramips: define lzma-loader recipe for SEAMA devices
Define "Device/seama-lzma-loader" recipe for SEAMA devices to help
contributors avoid doing recipe mistakes.

In a forum topic [0] I was under the impression that the good old
uimage-lzma-loader didn't fix the LZMA ERROR 1 for a device.

It was found out, that the uimage-lzma-loader never worked because the
KERNEL variable was overriden earlier (also an LZMA ERROR 1 related
commit, 6fba88de19), and the "use lzma-loader" fix (commit
09faa73c53) didn't catch that to include the "loader-kernel" part.

I contributed an LZMA ERROR 1 fix (commit ce19571004) for the SEAMA
device D-Link DIR-860L B1, where I had to duplicate the whole
uimage-lzma-loader recipe because of the special needs of the vendor
bootloader.

This new recipe reuse most of uimage-lzma-loader's KERNEL definiton to
avoid duplication.

It uses "relocate-kernel" as it needed for D-Link DIR-860L B1 to
boot from flash, and it's compatible with D-Link DIR-645 too.

It repacks lzma-loader with lzma for kernel (without uImage), because
these weird hacked vendor bootloaders accepts only LZMA compressed
kernels from flash:

    We have SEAMA, Image Size = 4759794
    Verifying Checksum ...
    Uncompressing SEAMA linux.lzma ... OK

It uses uImage header for initramfs kernel to be little bit verbose.

0: https://forum.openwrt.org/t/136435/10

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2022-11-12 18:15:55 +01:00
Arne Zachlod
ffa4b5283b ramips: add support for Mikrotik LtAP-2HnD
Mikrotik LtAP-2HnD is a outdoor/automotive WLAN 4 router with integrated GPS
receiver and two mPCIe slots.

Specifications:
* SoC: MT7621A
* RAM: 128 MiB Nanya NT5CC64M16GP-DI
* Flash: 16 MiB winbond W25Q128JV
* WLAN:
  * Atheros AR9382 with power amplifier SKY 85330 (2x2 internal antennas,
    with RF switches for external connectors)
* Ethernet: 1 Gbps, single port
* USB Host: USB 2.0 Speeds
* Serial: 115200 baud
* LEDs: Power, System, GPS, 5* RSSI
*  mPCIe:
   * miniPCIe slot 1: PCIe and USB 2.0 Host (via switch shared with USB Host)
   * miniPCIe slot 2: USB 2.0 and 3.0
* SIM Cards:
  * Slot 1 Connected to mPCIe slot 1
  * Slot 2 and 3 connected to mPCIe slot 2 via switch
* GPS: MTK 3333 on serial port 2 (/dev/ttyS1), 115200 baud and PPS on gpio 14

gpios are exposed to /sys/class/gpio:

* usb-select: swithes USB 2.0 interface between external port and internal
mPCIe slot 1 default is the external USB interface
* gps-reset: resets the GPS interface chip
* sim-select: switches between sim slot 2 and 3 connected to mPCIe slot 2
* gps-ant-select: switches GPS antenna between internal antenna and SMA
connected antenna
* lte-reset: resets mPCIe slot 2

Flashing:
 TFTP boot initramfs image and then perform sysupgrade. Follow common
 MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
2022-11-12 18:15:55 +01:00
Will Moss
5a1af6ed62 ath79: fix MAC address assignment for TP-Link ar7241 devices
On TP-Link ar7241 devices LAN and WAN interfaces are swapped. Keeping
that in mind fix MAC address assignment as used in vendor firmware:
LAN MAC - main MAC stored in u-boot and printed on label
WAN MAC - LAN MAC + 1

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-12 17:10:12 +01:00
Shiji Yang
4778f6e959 ath79: move usb led trigger node to SoC dtsi
These frequently used usb led triggers are universal. They should be
moved to SoC dtsi.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-12 17:10:12 +01:00
John Audia
e7bd3767a9 kernel: bump 5.10 to 5.10.154
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-12 17:05:13 +01:00
John Audia
0252c0b1bc kernel: bump 5.15 to 5.15.78
All patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-12 17:05:13 +01:00
Quintin Hill
4c3f664c2f kernel: backport some Bluetooth RTL8761 USB IDs
These USB IDs appear in the 5.15 stable kernel series but not the 5.10
stable series.

Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
2022-11-12 17:05:13 +01:00
Quintin Hill
5e6e45b7ff kernel: backport RTL8761B FW name change to v5.10
Make the firmware filenames referenced by the module consistent for
v5.10 and v5.15 kernels.  Backport two upstream patches a cleanup commit
and the commit making the change, the former is required for the latter
to apply cleanly.

Signed-off-by: Quintin Hill <stuff@quintin.me.uk>
2022-11-12 17:05:13 +01:00
Rafał Miłecki
797177ad85 kernel: update U-Boot nvmem driver to v6.2 release version
Backport queued patches that
1. Fix CRC32 calculation for redundant images
2. Fix CRC32 on big-endian
3. Fix parting images with Broadcom header

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-12 11:42:05 +01:00
Rafał Miłecki
ce296b1aeb bcm4908: refresh kernel 5.15 config
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-11 17:21:55 +01:00
Rafał Miłecki
66b6414a20 bcm4908: prepare support for kernel 5.15
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-11 17:21:55 +01:00
Rafał Miłecki
45ac906c64 bcm4908: update DTS files with the latest changes
The most affecting change is move of files from bcm4908/ to the bcmbca/.
That required updating few paths.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-11 15:37:57 +01:00
Daniel Golle
e586de8dbf
ath79: add support for Teltonika RUT300
Add support for the Teltonika RUT300 rugged industrial Ethernet router

Hardware
--------
SoC:    Qualcomm Atheros QCA9531
RAM:    64M DDR2 (EtronTech EM68B16CWQK-25IH)
FLASH:  16M SPI-NOR (Winbond W25Q128)
ETH:    4x 100M LAN (QCA9533 internal AR8229 switch, eth0)
        1x 100M WAN (QCA9533 internal PHY, eth1)
UART:   115200 8n1, same debug port as other Teltonika devices
USB:    1 single USB 2.0 host port
BUTTON: Reset
LED:    1x green power LED (always on)
        5x yellow Ethernet port LED (controlled by Linux)
        WAN port LED is used as boot status and upgrade indicator as
        the power LED cannot be controlled in software.

Use the *-factory.bin file to intially flash the device using the
vendor firmware's Web-UI.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-10 21:35:34 +00:00
Felix Fietkau
04b8ad60fd kernel: more fixes for mtk_eth_soc performance optimization
- fix features sync between netdevs
- fix crash in dsa_switch_rcv

Fixes: ceb1451c10 ("kernel: add mediatek soc ethernet performance improvements")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-10 22:27:18 +01:00
Felix Fietkau
7bd314a577 kernel: fix vlan parsing issue in mediatek ethernet driver
Check the vlan rx offload flag
Sync features across netdevs

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-10 13:20:57 +01:00
Rafał Miłecki
e4770db163 kernel: support "linux,rootfs" DT property for splitting rootfs
OpenWrt's support for splitting rootfs (to create an extra "rootfs_data"
partition) is limited to partitions called "rootfs". Upstream kernel
allows any name partition to be rootfs if it has "linux,rootfs" property
set. Add split support to such partitions in OpenWrt code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-10 12:47:22 +01:00
Rafał Miłecki
8cdafa149e bcm53xx: update DTS files with the latest changes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-10 09:51:25 +01:00
Weiping Yang
9945d05171 ipq40xx: add support for GL.iNet GL-A1300
Specifications:
SOC:		Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:		256 MiB
FLASH1:		4 MiB NOR
FLASH2:		128 MiB NAND
ETH:		Qualcomm QCA8075
WLAN1:		Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:		Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB:		1 x USB 3.0 port
Button:		1 x Reset button
Switch:		1 x Mode switch
LED:		1 x Blue LED + 1 x White LED

Install via uboot tftp or uboot web failsafe.

By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize

By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1

Afterwards upgrade can use sysupgrade image.

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2022-11-09 23:34:37 +01:00
Edward Chow
79107116d1 ath79: calibrate TL-WDR4900 v2 with nvmem-cells
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-09 22:55:33 +01:00
Shiji Yang
8d4c22a956 ath79: add missing clock name strings in SoC dtsi
For all SoC in the ath79 target, the PLL controller provides 3 main
clocks "cpu", "ddr" and "ahb" through the input clock "ref".

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-09 22:55:33 +01:00
Shiji Yang
520c90854c ath79: move reference clock node to SoC dtsi
AR7161, AR724x, AR9132 and QCA95xx only support fixed frequency external
crystal oscillator, so move reference clock node to SoC dtsi files.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-09 22:55:33 +01:00
Felix Fietkau
a06e023b4e mac80211: remove old legacy legacy drivers
Get rid of drivers that are either limited to 802.11b/g or don't even support
cfg80211/mac80211. Most of these are either limited to boards that we don't even
support anymore because of firmware size, or were only used for custom hacks by
a really small number of users in the past.
Let's get rid of those to reduce the maintenance effort and the number of useless
packages

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:44:28 +01:00
Felix Fietkau
f753316f4a mediatek: filogic: enable maxlinear PHY support, refresh config
Needed for the 7986 RFB1 board

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:55 +01:00
Felix Fietkau
5faff99c7b mediatek: filogic: fix mt7986a ethernet devicetree entries
Add all ports, rename DSA ports to start at lan1

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:51 +01:00
Felix Fietkau
4f1e54801e mediatek: drop the use of device tree overlays on mt7986a-rfb board
The boot loader does not support it. Instead make NAND the default image for
this board

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 20:43:45 +01:00
Felix Fietkau
ceb1451c10 kernel: add mediatek soc ethernet performance improvements
- implement multiqueue via qdma hardware shaper to deal with ports with different speeds
- implement hardware DSA untagging
- add NETIF_F_ALL_TSO to reduce unnecessary segmentation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-09 18:18:27 +01:00
Edward Matijevic
2964e5024c
ipq806x: kernel ramoops storage for C2600/AD7200
Define the kernel crash log storage ramoops/pstore feature
for C2600/AD7200 and add kmod-ramoops to default.

Tested with C2600 only.

Signed-off-by: Edward Matijevic <motolav@gmail.com>
2022-11-09 17:07:15 +01:00
David Bauer
10ba380ec3 ramips: define loadaddr for U6 Lite DTB
The Ubiquiti UniFi 6 Lite does not correctly align the FDT by always
setting fdt_high to 0xffffffff when invoking the bootubnt command.

Work around this issue by loading the DTB to a valid,aligned address, so
the bootloader does not have to relocate the FDT automatically.

Note: The device does read the kernel before invoking bootm on the FIT
image to 0x86000000.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-11-08 12:16:43 +01:00
Rafał Miłecki
d33e49857e kernel: backport support for "linux,rootfs" in DT
This DT property allows marking flash partition that Linux should use as
a root device. It's useful for devices that don't use U-Boot and cmdline
parser for partitioning. It may be used with "fixed-partitions" or some
dynamic partitioning based on flash content.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-08 09:12:16 +01:00
Rafał Miłecki
6a64eb2664 kernel: split out mtd hack for CONFIG_FIT_PARTITION + rootfs
This is some hack on top of our old hack. Use separated patch for it so
it's easier to understand and actually possible to describe. We should
ideally get rid of this (and we actually did with kernels 5.15+).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-08 09:12:05 +01:00
Michael Lyle
961e01fc67 ramips: gl-mt1300: downclock SPI to 50MHz
The SPI max frequency was set to 80MHz, considerably higher than the
vendor clocks it in their firmware (10MHz).  Multiple users reported
jffs2 corruption/instability in GitHub issue #10461.

My unit has a W25Q256; datasheet specifies maximum SPI frequency for
read command of 50MHz.

Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read;
and @MPannen1979 for identifying the problem.

Fixes: #10461
Signed-off-by: Michael Lyle <mlyle@lyle.org>
2022-11-07 12:54:31 +01:00
Sungbo Eo
02aa7a2bb9 ramips: fix TP-Link RE200 v3/v4 LEDs
Set power LED to gpio 43 instead of 44 for v3 and v4.
Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`).

Tested by the author of the initial v3 and v4 commit.

Reported-by: Richard Fröhning <misanthropos@gmx.de>
Tested-by: Richard Fröhning <misanthropos@gmx.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-11-07 12:33:42 +01:00
Alan Luck
aca8bb5cc3 ath79: expand rootfs for DIR-825-B1 with unused space
Expand currently unused flash space to roofs for DIR-825-B1 by using the same
flash space as the old ar71xx big image without moving the caldata.

With some testing this partition is use by the OEM firmware
but if changed is regenerated which allows reverting to OEM firmware

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
2022-11-06 01:03:16 +01:00
Korey Caro
12cee86989 ath79: add support to TrendNet TEW-673GRU
Add support for the TrendNet TEW-673GRU to ath79.
This device was supported in 19.07.9 but was deprecated with ar71xx.
This is mostly a copy of D-Link DIR-825 B1.
Updates have been completed to enable factory.bin and sysupgrade.bin both.
Code improvements to DTS file and makefile.

Architecture   |  MIPS
Vendor         |  Qualcomm Atheros
bootloader     |  U-Boot
System-On-Chip |  AR7161 rev 2 (MIPS 24Kc V7.4)
CPU/Speed      |  24Kc V7.4 680 MHz
Flash-Chip     |  Macronix MX25L6405D
Flash size     |  8192 KiB
RAM Chip:      |  ProMOS V58C2256164SCI5 × 2
RAM size       |  64 MiB
Wireless       |  2 x Atheros AR922X 2.4GHz/5.0GHz 802.11abgn
Ethernet       |  RealTek RTL8366S Gigabit w/ port based vlan support
USB            |  Yes 2 x 2.0

Initial Flashing Process:
	1) Download 22.03 tew-673gru factory bin
	2) Flash 22.03 using TrendNet GUI

OpenWRT Upgrade Process
	3) Download 22.03 tew-673gru sysupgrade.bin
	4) Flash 22.03 using OpenWRT GUI

Signed-off-by: Korey Caro <korey.caro@gmail.com>
2022-11-06 00:51:58 +01:00
Linos Giannopoulos
78110c3b5f ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.

- Specifications:

* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
  Signal3

- MAC Addresses:

OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN

- Installation:

1. Download the OpenWrt initramfs-image.

Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.

3. Connect to the serial console.

Attach power and interrupt the boot procedure when prompted (type `tpl`).

Credentials are admin / 1234

4. Configure U-Boot for booting OpenWrt from ram

 $ tftpboot
 $ bootm

5. Transfer the OpenWrt sysupgrade image to the device.

- LTE:

In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
        option device '/dev/cdc-wdm0'
        option proto 'qmi'
        option pincode 'XXXX'
        option apn 'your_isp_apn'
```

2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`

Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
2022-11-05 23:13:16 +01:00
Shiji Yang
f7f9203854 ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1
SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based
on Tenbay WR1800K. They have the same hardware circuits and u-boot.
SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile),
SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these
models run the same firmware.

Specifications:
 SOC:      MT7621 + MT7905 + MT7975
 ROM:      128 MiB
 RAM:      256 MiB
 LED:      status *3 R/G/B
 Button:   reset *1 + wps/mesh *1
 Ethernet:      lan *3 + wan *1 (10/100/1000Mbps)
 TTL Baudrate:  115200
 TFTP Server:   192.168.1.254
 TFTP IP:       192.168.1.28 or 192.168.1.160 (when envs is broken)

MAC Address:
 use        address               source
 label      30:xx:xx:xx:xx:62     wan
 lan        30:xx:xx:xx:xx:65     factory.0x8004
 wan        30:xx:xx:xx:xx:62     factory.0x8004 -3
 wlan2g     30:xx:xx:xx:xx:64     factory.0x0004
 wlan5g     32:xx:xx:xx:xx:64     factory.0x0004 set 7th bit

TFTP Installation (initramfs image only & recommend):
1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0
2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root
   directory of the tftp server. (tftpd64 is a good choice for Windows)
3. Start the TFTP server, plug in the power supply, and wait for the
   system to boot.
4. Backup "firmware" partition and rename it to "firmware.bin", we need
   it to back to stock firmware.
5. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
6. Apply sysupgrade.bin in OpenWrt LuCI.

Web UI Installation:
1. Apply update by uploading initramfs-factory.bin to the web UI.
2. Use "fw_printenv" command to list envs.
   If "firmware_select=2" is observed then set u-boot enviroment:
   /# fw_setenv firmware_select 1
3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI.

Recovery to stock firmware:
a. Upload "firmware.bin" to OpenWrt /tmp, then execute:
   /# mtd -r write /tmp/firmware.bin firmware
b. We can also write factory image "UploadBrush-bin.img" to firmware
   partition to recovery. Upload image file to /tmp, then execute:
   /# mtd erase firmware
   /# mtd -r write /tmp/UploadBrush-bin.img firmware

How to extract stock firmware image:
  Download stock firmware, then use openssl:
  openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \
  -out "firmware.tar.tgz" -k QiLunSmartWL

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 22:38:01 +01:00
Alexander Horner
53f2e438cb ramips: add support for Zbtlink ZBT-WG1602-V04
Description heavily based on commit
7e89421a7c by
Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have
been removed

Completed with great help from \x on IRC. Thanks, \x!

Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN
(UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe
slots with USB and SIM only and another one which is a pure miniPCIe
slot as well as five Gigabit Ethernet ports (4xLAN + WAN).

Specification:

* SoC: MT7621A
* RAM: 256/512 MiB
* Flash: 16/32 MiB
* Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN)
* WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2)
* WLAN 5GHz: MT7662E (.11nac, MIMO 2x2)
* WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios
* miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus
* WWAN Ants: detachable x4
* External storage: microSD (SDXC) slot
* USB: 3.0 Type-A port
* LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled,
  1 power indicator)
* Button: 1 (reset)
* UART: console (115200 baud)
* Power: DC jack (12 V / 2.5 A)

Additional HW information:

* SoC USB port 1 is shared by internal miniPCIe slot and external
  Type-A USB port, USB D+/D- lines are toggled between ports using a
  GPIO controlled DPDT switch.

Installation:

The kernel image can be installed directly onto the device via a browser
to 192.168.1.1 using the built in firmware recovery Web UI available.
It can be accessed by pushing the reset button in, applying power and
holding the reset button for approximately 10 seconds. When the kernel
image has been flashed, you can access LuCI and upload the sysupgrade
as normal.

Signed-off-by: Alexander Horner <ahorner@programmer.net>
2022-11-05 21:12:25 +01:00
Shiji Yang
7a504c151d ramips: add support for Youku X2
Specifications:
  SOC:      MT7620AN + MT7612EN
  RAM:      128 MiB DDR2
  Flash:    16 MiB (Winbond W25Q28FVFG)
  WLAN:     2.4G + 5G
  LAN:      LAN ports *2
  WAN:      WAN port *1
  USB:      USB2.0 *1
  SD Card:  MicroSD *1
  Buttons:  Reset *1
  LEDs: ethernet *3, system, usb, wlan2g, wlan5g

MAC Address:
  use        address               source
  label      54:36:9b:xx:xx:ac     lan
  lan        54:36:9b:xx:xx:ac     factory.0x0028
  wan        54:36:9b:xx:xx:ad     factory.0x002e
  wlan2g     54:36:9b:xx:xx:ae     factory.0x0004
  wlan5g     54:36:9b:xx:xx:af     factory.0x8004

Installation:
1. Apply initramfs-kernel.bin in stock firmware Web UI.
2. Install sysupgrade.bin on OpenWrt and do not retain any configuration.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 21:12:24 +01:00
Shiji Yang
eba0a8deb6 ramips: improve compatibility for Youku YK-L2 and YK-L1 series
Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install
initramfs-kernel.bin from the stock firmware Web UI. At the same time,
this change makes it possible to boot OpenWrt with the official u-boot.

Notice:
Since the stock firmware is based on OpenWrt and the configuration
will be retained by default during the upgrade process, so we must use
initramfs-kernel.bin to do a initial installation. After the system
restarts, install sysupgrade.bin and do not retain any configuration.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-11-05 21:12:24 +01:00
Martin Schiller
1e028ac51e kernel: further cleanup of xfrm[4|6]_mode*
In my commit da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_*
modules") I missed a few default config options and description entries.
Those should be gone as well.

Fixes: da5c45f4d8 ("kernel: remove handling of xfrm[4|6]_mode_* modules")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2022-11-05 16:28:33 +01:00
Luiz Angelo Daros de Luca
1ee635c561 realtek: fix typo in debug message
vid_end was mentioned twice.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2022-11-05 16:27:21 +01:00
John Audia
1eebe72a80 kernel: bump 5.15 to 5.15.77
Manually rebased:
   bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
   lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:38 +01:00
John Audia
87edb650c7 kernel: bump 5.10 to 5.10.153
Manually rebased:
  bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
  lantiq/patches-5.10/0028-NET-lantiq-various-etop-fixes.patch

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:00 +01:00
Nick Hainke
29d987fc89 mediatek: replace mt7986 watchdog assert patch with upstream
Replace "920-watchdog-add-mt7986-assert.patch" with upstreamed
- 920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch
- 921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
61a9367b86 mediatek: mt7629: add tag to upstreamed patches
The patches were upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
0c8d84a642 mediatek: add tag for upstreamed patches
The patches were upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
e8080ce89b mediatek: mt7986: add tag to upstreamed patches
The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and
"212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Nick Hainke
e4270d6493 mediatek: mt7622: add tag to upstreamed patches
The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch"
and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are
upstreamed to 5.19.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-11-05 14:07:46 +00:00
Aleksander Jan Bajkowski
985d59cdf0 mediatek: filogic: disable swconfig
This subtarget supports 3 devices:
 * Bananapi BPi-R3 (added in a96382c1bb),
 * MediaTek MTK7986 rfba AP (added in cffc77ae55),
 * MediaTek MTK7986 rfbb AP (added in cffc77ae55).

This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG
was copied from another config when the subtarget was created.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-05 14:02:13 +00:00
Aleksander Jan Bajkowski
c4f63f7364 mediatek: filogic: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-05 14:02:13 +00:00
Rafał Miłecki
6198eb3e64 bcm4908: backport upstream BQL support for bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-03 07:38:35 +01:00
Hauke Mehrtens
e42ec112a4 kernel: Refresh generic patches
This patch was out of sync.

Fixes: 1673b7dca3 ("kernel: backport fixes for MediaTek Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-11-03 00:25:34 +01:00
Daniel Golle
1673b7dca3 kernel: backport fixes for MediaTek Ethernet driver
Backport patches from net-next which fix possible memory and resource
leaks in the error codepaths of WED initialization.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-02 15:53:34 +00:00
Daniel Golle
9721a42a27
kernel: support hw flow-offloading counters on newer MediaTek SoCs
The packet processing engine (PPE) found in newer ARM-based MediaTek
SoCs provides packet and byte counters for offloaded streams.
Import pending patch reading and using those counters.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-02 11:41:56 +00:00
Daniel Golle
82a05ce14b
mediatek: remove obsolete patch
The patch enabling hardware flow offloading support on the MT7623 SoC
has been merged upstream as of Linux 5.13. Remove our local patch which
wrongly got forward-ported and now actually enables hardware flow
offloading for the MT2701 SoC family (unsupported in OpenWrt).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-02 11:41:50 +00:00
Sander Vanheule
75c576d4c4 realtek: mark clock source as continuous
After replacing the R4K event timer and clock source with the new
Realtek Otto timer, performance for RTL839x devices was severely
impacted, as reported by Hiroshi.

Research by Markus showed that after commit 4657a5301e ("realtek:
avoid busy waiting for RTL839x PHY read/write"), the ethernet driver
could only update a phy once per timer interval, which also heavily
impacted boot time. On e.g. a Zyxel GS1900-48, this added around a
minute to the time to fully initialise the switch.

By marking the otto clocksource as continuous, the kernel enables it to
be used for high resolution timers. This allows readx_poll_timeout() to
sleep for less than one system timer interval, reducing system dead
time.

Link: https://github.com/openwrt/openwrt/issues/11117
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Cc: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> # Panasonic Switch-M48eG PN28480K
Tested-by: Jan Hoffmann <jan@3e8.eu> # HPE 1920-8G, HPE 1920-48G
2022-11-01 09:13:11 +01:00
Rosen Penev
3b93651072 target/realtek: use netif_receive_skb_list
Small performance improvement on rx.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2022-11-01 09:09:24 +01:00
Daniel Golle
e131a66e30
mediatek: consider adc_oe thermal calibration value in efuse
The use of the adc_oe value stored in the efuse has been dropped in
MediaTek's SDK during a recent refactorization of the temperature
calculation formula. Don't ignore this offset value and again include
it in raw-to-deg-celsius calculation.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-31 22:37:05 +00:00
Volodymyr Puiul
08e153c3c3 ramips: add support for YunCore FAP690
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI NOR
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 1x 1GiE via MT7530
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)

- Bootloader: U-Boot
- Buttons:
    - SW1 - no label on the box, combined with led
- Led: Status. RGB controlled by
    - GPIO 14 - green color
    - GPIO 15 - red color
    - GPIO 16 - blue color

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
it will not boot.

MAC addresses as verified by OEM firmware:
vendor   source
LAN      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
	4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-31 22:01:49 +01:00
Martin Schiller
da5c45f4d8 kernel: remove handling of xfrm[4|6]_mode_* modules
For kernel versions before 5.2, the required IPsec modes have to be
enabled explicitly (they are built-in for newer kernels).

Commit 1556ed155a ("kernel: mode_beet mode_transport mode_tunnel xfram
modules") tried to handle this, but it does not really work.

Since we don't support these kernel versions anymore and the code is
also broken, let's remove it.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[Remove old generic config options too]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 21:58:15 +01:00
Hauke Mehrtens
95c216806b at91: Remove CONFIG_PINCTRL_MCP23S08 configuration option
The CONFIG_PINCTRL_MCP23S08 configuration option is already unset in the
generic kernel configuration.

Fixes: f938512af6 ("target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 00:46:15 +01:00
Hauke Mehrtens
d15fed98ec Revert "at91:"
This reverts commit 7cc6ffa1b9.

This should have been folded in an other commit.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-31 00:45:52 +01:00
Hauke Mehrtens
7cc6ffa1b9 at91:
[CONFIG_PINCTRL_MCP23S08 is already unset in generic config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-30 23:37:53 +01:00
Volodymyr Puiul
3d14c610e8 ramips: add support for YunCore FAP640
It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A.

Specifications:
- SoC: MT7621AT (880MHz, 2 Cores)
- RAM: 128 MB
- Flash: 16 MB SPI
- Wi-Fi:
    - MT7915DN + MT7905DAN: 2.4/5 GHz
- Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN
- UART: J4 (115200 baud)
    - Pinout: [3V3] (TXD) (RXD) (GND)
- Power: 802.11af/at PoE;

- Bootloader: U-Boot
- Buttons:
    - Reset
- LEDs:
    - Status - RGB controlled by
      - GPIO 14 LOW - green color
      - GPIO 15 LOW- red color
      - GPIO 16 LOW - blue color
    - WAN - gren color, controlled by switch GPIO 12 LOW
    - LAN1 - gren color, controlled by switch GPIO 9 HIGH
    - LAN2 - gren color, controlled by switch GPIO 6 LOW
    - LAN3 - gren color, controlled by switch GPIO 3 LOW
    - LAN4 - gren color, controlled by switch GPIO 0 LOW

Installation:
OEM firmware is based on LEDE with custom UI and support standard sysupgrade
variant of firmware. However it requires "*.ubin" extension for sysupgrade file.
Always select "Factory reset" switch on upgrade to OpenWRT, otherwise
router will not boot.

MAC addresses with OEM firmware:
vendor   source
lan      factory 0x4 (label)
5g       factory 0x4 (label)
2g       label with flipped bits bit in 1-st byte and bits 5, 6, 7 in
  4-th byte

Example
label:  44:xx:xx:b7:xx:xx
lan:    44:xx:xx:b7:xx:xx
2g      46:xx:xx:c7:xx:xx
5g      44:xx:xx:b7:xx:xx

Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
2022-10-30 23:14:45 +01:00
Csaba Sipos
cc8b8f1b41 ipq40xx: add support for MikroTik hAP ac3 LTE6 kit
This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD
(hAP ac³ LTE6 kit), an  indoor dual band, dual-radio 802.11ac
wireless AP with built-in Mini PCI-E LTE modem, one USB port, five
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/hap_ac3_lte6_kit for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port
 - 1x USB Type A port
 - 1x Mini PCI-E port (supporting USB)
 - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6)

Installation:

Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6).

0. Export your MikroTik license key (in case you want to use the device with RouterOS later)
1. Boot the initramfs image via TFTP
2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder
3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin
4. Recovery to factory software is possible via Netinstall:
   https://help.mikrotik.com/docs/display/ROS/Netinstall

Signed-off-by: Csaba Sipos <metro4@freemail.hu>
2022-10-30 23:14:45 +01:00
Florian Eckert
80edacc8a6 target/mxs: replace gpio-mcp23s08 with pinctrl-mcp23s08
The dependency on the kernel module gpio-mcp23s08 is replaced by
pinctrl-mcp23s08-spi and pinctrl-mcp23s08-i2c, as the gpio-mpc23s08 kernel
module no longer exists.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Florian Eckert
29ae20519a kernel: remove CONFIG_GPIO_MCP23S08 from default kernel configs
The kernel config option 'CONFIG_GPIO_MCP23S08' no longer exists.
Therefore, it is removed from the generic kernel configuration for
linux-5.10 and linux-5.15.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Florian Eckert
f938512af6 target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config
Adapt the device package to no longer use the gpio-mcp23s08 but instead
use the pinctrl-mcp23s08-spi. In addition, the kernel configuration was
adapted so that this can be built as a module and does not have to be
integrated directly into the kernel for this target.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2022-10-30 23:14:45 +01:00
Edward Chow
50f727b773 ath79: add support for Linksys EA4500 v3
Add support for the Linksys EA4500 v3 wireless router

Hardware
--------
SoC:    Qualcomm Atheros QCA9558
RAM:    128M DDR2 (Winbond W971GG6KB-25)
FLASH:  128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN:   QCA9558 3T3R 802.11 bgn
        QCA9580 3T3R 802.11 an
ETH:    Qualcomm Atheros QCA8337
UART:   115200 8n1, same as ea4500 v2
USB:	1 single USB 2.0 host port
BUTTON: Reset - WPS
LED:    1x system-LED
        LEDs besides the ethernet ports are controlled
        by the ethernet switch

MAC Address:
 use        address(sample 1)    source
 label      94:10:3e:xx:xx:6f   caldata@cal_macaddr
 lan        94:10:3e:xx:xx:6f   $label
 wan        94:10:3e:xx:xx:6f   $label
 WiFi4_2G   94:10:3e:xx:xx:70   caldata@cal_ath9k_soc
 WiFi4_5G   94:10:3e:xx:xx:71   caldata@cal_ath9k_pci

Installation from Serial Console
------------

1. Connect to the serial console. Power up the device and interrupt
   autoboot when prompted

2. Connect a TFTP server reachable at 192.168.1.0/24
   (e.g. 192.168.1.66) to the ethernet port. Serve the OpenWrt
   initramfs image as "openwrt.bin"

3. To test OpenWrt only, go to step 4 and never execute step 5;
   To install, auto_recovery should be disabled first, and boot_part
   should be set to 1 if its current value is not.

   ath> setenv auto_recovery no
   ath> setenv boot_part 1
   ath> saveenv

4. Boot the initramfs image using U-Boot

   ath> setenv serverip 192.168.1.66
   ath> tftpboot 0x84000000 openwrt.bin
   ath> bootm

5. Copy the OpenWrt sysupgrade image to the device using scp and
   install it like a normal upgrade (with no need to keeping config
   since no config from "previous OpenWRT installation" could be kept
   at all)

   # sysupgrade -n /path/to/openwrt/sysupgrade.bin

Note: Like many other routers produced by Linksys, it has a dual
      firmware flash layout, but because I do not know how to handle
      it, I decide to disable it for more usable space. (That is why
      the "auto_recovery" above should be disabled before installing
      OpenWRT.) If someone is interested in generating factory
      firmware image capable to flash from stock firmware, as well as
      restoring the dual firmware layout, commented-out layout for the
      original secondary partitions left in the device tree may be a
      useful hint.

Installation from Web Interface
------------

1. Login to the router via its web interface (default password: admin)

2. Find the firmware update interface under "Connectivity/Basic"

3. Choose the OpenWrt factory image and click "Start"

4. If the router still boots into the stock firmware, it means that
   the OpenWrt factory image has been installed to the secondary
   partitions and failed to boot (since OpenWrt on EA4500 v3 does not
   support dual boot yet), and the router switched back to the stock
   firmware on the primary partitions. You have to install a stock
   firmware (e.g. 3.1.6.172023, downloadable from
   https://www.linksys.com/support-article?articleNum=148385 ) first
   (to the secondary partitions) , and after that, install OpenWrt
   factory image (to the primary partitions). After successful
   installation of OpenWrt, auto_recovery will be automatically
   disabled and router will only boot from the primary partitions.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-10-30 23:14:45 +01:00
John Audia
910bdda6af kernel: bump 5.15 to 5.15.76
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:57:25 +01:00
John Audia
af1e3439a8 rockchip: armv8: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:55:00 +01:00
John Audia
86ba286766 mvebu: cortexa72: add CONFIG_ARM64_ERRATUM_1742098
5.15.76 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:55:00 +01:00
John Audia
8e7cc06254 kernel: add # CONFIG_ARM64_ERRATUM_1742098
Introduced with 5.15.76[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.76&id2=v5.15.75

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
a34255b795 kernel: bump 5.15 to 5.15.75
Removed upstreamed:
   bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1]

Manually rebased:
   patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
   bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
   bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
   bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All other patches automatically rebased

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=2810061452f9b748b096ad023d318690ca519aa3

Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
a133423c59 kernel: add # CONFIG_ARM64_ERRATUM_2441007 symbol
Introduced with 5.15.75.[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.75&id2=v5.15.74

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
52400e167d kernel: bump 5.10 to 5.10.152
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
dab23d04af layerscape: armv8_64b: add CONFIG_ARM64_ERRATUM_1742098
5.10.152 introduces a new symbol that applies Cortex-A72 SoCs so enable it[1].

https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.10.152&id2=v5.10.151

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
7a27ac605c kernel: bump 5.10 to 5.10.151
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
aa2fa2eb76 kernel: bump 5.10 to 5.10.150
Manually rebased:
  bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch

All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-30 17:52:42 +01:00
Chukun Pan
641e4f2f04 mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128 MB
  RAM: K4A4G165WF-BCWE 512 MB
  Ethernet: 4x 10/100/1000 Mbps
  WiFi1: MT7976GN 2.4GHz ax 4x4
  WiFi2: MT7976AN 5GHz ax 4x4
  Button: Mesh, Reset

Flash instructions:
  1. Gain ssh and serial port access, see the link below:
     https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
  2. Use ssh or serial port to log in to the router, and
     execute the following command:
     nvram set boot_wait=on
     nvram set flag_boot_rootfs=0
     nvram set flag_boot_success=1
     nvram set flag_last_success=1
     nvram set flag_try_sys1_failed=8
     nvram set flag_try_sys2_failed=8
     nvram commit
  3. Set a static ip on the ethernet interface of your computer
     (e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
  4. Download the initramfs image, rename it to initramfs.bin,
     and host it with the tftp server.
  5. Interrupt U-Boot and run these commands:
     setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
     saveenv
     tftpboot initramfs.bin
     bootm
  6. After openwrt boots up, use scp or luci web
     to upload sysupgrade.bin to upgrade.

Revert to stock firmware:
  Restore mtdparts back to default, then use the
  vendor's recovery tool (Windows only).

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-30 14:30:22 +00:00
Olliver Schinagl
f4849c0ab7 realtek: Fix CRC offloading for rtl83xx
In rtl83xx_set_features we set bit 3 to enable, and bit 4 to disable
checksuming. Looking at rtl93xx_set_features we however see that for
both enable and disable the same bit is used (bit 4). This can't be
right, especially as bit 4 for rtl83xx seems to be Collision threshold
occupying 2 bits. Change this to make this more logical.

Fixes: 9e8d62e421 ("realtek: enable CRC offloading")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
2022-10-29 11:18:04 +02:00
Christian Marangi
5384c9337f
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.

Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.

The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-28 01:16:00 +02:00
Christian Marangi
c4a9a67de8
ipq806x: disable ea8500 image by default
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.

Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.

The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-28 01:10:21 +02:00
Rafał Miłecki
ae57770c95 bcm4908: add pending BQL support for bcm4908_enet
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 22:34:00 +02:00
Rafał Miłecki
31e4e56654 bcm4908: backport bcm4908_enet fix for NULL dereference
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 21:14:02 +02:00
Rafał Miłecki
6a02205a4d bcm4908: optimize Ethernet driver by using build_skb()
This should slightly improve performance thanks to the better cache
usage.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-27 18:59:46 +02:00
Jan Hoffmann
eb456aedfe realtek: use assisted learning on CPU port
L2 learning on the CPU port is currently not consistently configured and
relies on the default configuration of the device. On RTL83xx, it is
disabled for packets transmitted with a TX header, as hardware learning
corrupts the forwarding table otherwise. As a result, unneeded flooding
of traffic for the CPU port can already happen on some devices now. It
is also likely that similar issues exist on RTL93xx, which doesn't have
a field to disable learning in the TX header.

To address this, disable hardware learning for the CPU port globally on
all devices. Instead, enable assisted learning to let DSA write FDB
entries to the switch.

For now, this does not sync local/bridge entries to the switch. However,
support for that was added in Linux 5.14, so the next switch to a newer
kernel version is going to fix this.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-26 09:59:38 +02:00
Jan Hoffmann
2088e440b1 realtek: set up L2 table entries properly
Initialize the data structure using memset to avoid the possibility of
writing garbage values to the hardware.

Always set a valid entry type, which should fix writing unicast entries
on RTL930x.

For unicast entries, set the is_static flag to prevent the switch from
aging them out.

Also set the rvid field for unicast entries. This is not strictly
necessary, as the switch fills it in automatically from a non-zero vid.
However, this makes the code consistent with multicast entry setup.

While at it, reorder the statements and fix some style issues (double
space, comma instead of semicolon at end of statement). Also remove the
unneeded priv parameter and debug print for the multicast entry setup
function.

Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-26 09:59:24 +02:00
Christian Marangi
a31b598590
realtek: 5.10: refresh kernel patches
Refresh kernel patches for realtek 5.10 kernel

Refreshed patch:
- 300-mips-add-rtl838x-platform.patch

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 04:56:16 +02:00
Davide Fioravanti
8d921167e9
ipq40xx: convert to DSA and enable Netgear Orbi devices
Convert to DSA and enable again Netgear Orbi devices:
 - RBR50
 - RBS50
 - SRR60
 - SRS60

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2022-10-25 02:34:46 +02:00
Christian Marangi
ea63945b25
generic: 5.15: add missing CMDLINE_OVERRIDE patch
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.

Reintroduce it to fix Asrock G10 functionality.

Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
1c514f05ab
ipq806x: 5.15: drop mmc-ddr-1_8v from sdcc1 node
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.

Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
a87b6cda02
ipq806x: 5.15: revert unwanted DSA conversion for ASRock G10
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.

Revert this to swconfig driver to restore normal functionality.

Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:45 +02:00
Christian Marangi
dd2515cb53
ipq806x: 5.15: backport qcom_nandc patch for unprotected spare data fix
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.

Backport patch that fix this error and correctly handle error from
partition parser.

Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:44 +02:00
Christian Marangi
04a8944178
generic: 5.15: backport smempart parser fixup patch with EPROBE_DEFER error
Backport patch from kernel 5.15 that mute error on EPROBE_DEFER with
smempart parser.

This parser require the smem device to be probed first and currently it
may happen that mtd gets probed before the smem device causing an error
on the smempart parser. This error may be confusing and should be muted.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:44 +02:00
Christian Marangi
221020fda6
generic: 5.15: backport qcom smem patch for reserved-space support
In new kernel version from 5.16, smem node can be declared directly in
the reserved-space node. Upstream ipq806x (and to-be-merged) ipq807x
allign to this new implementation. Backport this patch to kernel 5.15 to
fix support for smem parser for ipq806x target.

Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-25 01:29:43 +02:00
Christian Marangi
ffe91ca478
generic: 5.15: move not backport patch to pending dir
Move patch wrongly placed in backport dir to pending dir as they still
didn't got merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:48 +02:00
Christian Marangi
2a7bdde29b
generic: 5.15: move MGLRU patches from pending to backport
Move MGLRU patches from pending to backport as they got merged upstream.
These are direct porting from one of the dev so it's better to just move
than trying to backport them again from upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:48 +02:00
Christian Marangi
ccedd7175d
generic: 5.15: move mvebu aardvark patch from pending to backport
Move mvebu aardvark patch from pending to backport as they got merged
upstream.
One additional patch is needed as a later fixup for it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:47 +02:00
Christian Marangi
08c6c0c217
generic: 5.15: move ZTE MF286D modem patch from pending to backport
Move ZTE MF286D modem patch from pending to backport as it was merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:47 +02:00
Christian Marangi
e25890ce45
generic: 5.15: move bluetooth mt79 usb id patch from pending to backport
Move bluetooth mt79 usb id patch from pending to backport as it got
merged upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:47 +02:00
Christian Marangi
a1522ec156
generic: 5.15: move mtk eth soc patch from pending to backport
Move mtk eth soc patch from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
d7a6e171c0
generic: 5.15: move sfp HALNy patch from pending to backport
Move sfp HALNy patch from pending to backport as they got merged
upstream. The patch was reordered and one was squashed in the upstream
variant.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
90629d82da
generic: 5.15: move pending xtx nand patch from pending to backport
Move pending xtx nand patch from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
f846945bd2
generic: 5.15: move dtc drop interrupt check from pending to backport
Move dtc drop interrupto check from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:46 +02:00
Christian Marangi
b182634689
generic: 5.15: move MIPS cpuinfo patch from pending to backport
Move MIPS cpuinfo patch from pending to backport as it got merged
upstream.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-24 21:10:45 +02:00
Shiji Yang
288b36c2ea ramips: add missing WAN LED for Xiaomi Mi Router 4A / 4C
The blue WAN LED connected to GPIO37 is missing, so re-add it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-10-23 23:33:22 +02:00
Sander Vanheule
9f6cbc78cd realtek: consistently flood RMA frames
The switches support different actions for incoming ethernet multicast
frames with Reserved Multicast Addresses (01-80-C2-00-00-{01-2F}). The
current code will set the 2-bit action field to FLOOD (0x3) for most
classes, but the highest bit is always unset for the relevant control
registers. This means the DROP (0x1) action being used for these
classes; whatever class the MSB happens to be in.

For RTL838x, this results in {20,23-2F} frames being dropped, instead of
flooding all ports. On other switch generations, {0F,1F,2F} frames are
dropped. This is inconsistent, and appears to be a mistake. Remove this
inconsistency by flooding all multicast frames with RMA addresses.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Sander Vanheule
039e5be4af realtek: remove RTL839x path in RTL838x multicast
The multicast setup function rtl838x_eth_set_multicast_list() checks if
the current SoC is a RTL839x family device. However, the function is
only included in the RTL838x ops table, so this path should never be
taken, making this dead code. rtl839x_eth_set_multicast_list() is
already present in the RTL839x ops table, so it should be safe to remove
this branch.

While touching the code, also re-sort the functions to match sorting
elsewhere, with rtl838x coming before rtl839x.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Jan Hoffmann
19b86658b7 realtek: reduce excessive logging for FDB operations
Currently several messages at KERN_INFO level are printed for every FDB
del/dump operation. This can cause a significant slowdown for example
while using "bridge fdb", and may even trigger a watchdog.

Remove most of these log messages, as the new L2 table debugfs node
should be a good replacement. Change the remaining messages to
KERN_DEBUG level.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-23 22:33:08 +02:00
Jan Hoffmann
ae9487c535 realtek: add debugfs node for L2 table
This allows to view all unicast and multicast entries that are currently
in the L2 hash table and the CAM.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-23 22:33:08 +02:00
Jan Hoffmann
4657a5301e realtek: avoid busy waiting for RTL839x PHY read/write
Switch to a polling implementation similar to the one for RTL838x, to
allow other kernel tasks to run while waiting.

Signed-off-by: Jan Hoffmann <jan@3e8.eu>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
b295c7140b realtek: disable otto timer for RTL93xx targets
The new timer is not yet ready for all targets. Avoid interactive
questions during build

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[rename symbol to CONFIG_REALTEK_OTTO_TIMER]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
beb5b07943 realtek: timer driver: activate for RTL839X devices
Use the	new timer driver for the RTL839X devices and remove the
no longer needed modules.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
ec675fb744 realtek: timer driver: activate for RTL838X devices
Use the new timer driver for the RTL838X devices. Remove the no
longer needed modules.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct timer compatible order, update selected symbols]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
5c677b2298 realtek: timer driver: documentation
Provide some helpful information about the devicetree configuration of
our new driver

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct compatible order in examples]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Markus Stockhausen
3cc8011171 realtek: resurrect timer driver
Now that we provide a clock driver for the Reltek SOCs the CPU frequency might
change on demand. This has direct visible effects during operation

- the CEVT 4K timer is no longer a stable clocksource
- after CPU frequencies changes time calculation works wrong
- sched_clock falls back to kernel default interval (100 Hz)
- timestamps in dmesg have only 2 digits left

[    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps ...
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.080000] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.090000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ...

Looking around where we can start the CEVT timer for RTL930X is a good basis.
Initially it was developed as a clocksource driver for the broken timer in that
specific SOC series. Afterwards it was shifted around to the CEVT location,
got SMP enablement and lost its clocksource feature. So we at least have
something to copy from. As the timers on these devices are well understood
the implementation follows this way:

- leave the RTL930X implementation as is
- provide a new driver for RTL83XX devices only
- swap RTL930X driver at a later time

Like the clock driver this patch contains a self contained module that is SOC
independet and already provides full support for the RTL838X, RTL839X and
RTL930X devices. Some of the new (or reestablished) features are:

- simplified initialization routines
- SMP setup with CPU hotplug framework
- derived from LXB clock speed
- supplied clocksource
- dedicated register functions for better readability
- documentation about some caveats

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[remove unused header includes, remove old CONFIG_MIPS dependency, add
REALTEK_ prefix to driver symbol]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-10-23 22:33:08 +02:00
Brian Norris
a3da858ab0 ipq40xx: Convert Google Wifi to DSA, reenable
Undo parts of these:

116feb4a1c ipq40xx: remove non-converted network configs
db19efee95 ipq40xx: disable boards not converted to DSA

Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock
bootloader has memorized them (instead of following aliases); then plug
the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the
'local-mac-address' property is no longer in the correct node.

Cc: David Bauer <mail@david-bauer.net>
Cc: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2022-10-23 08:27:40 +02:00
Jack Chen
57577bb8cc ipq40xx: convert to DSA and enable mobipromo,cm520-79f
Convert to DSA and enable the MobiPromo CM520-79F device again.

Signed-off-by: Jack Chen <redchenjs@live.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2022-10-23 01:45:52 +02:00
Pavel Kamaev
a716ac5564 ath79: fix reference clock for RouterBoard 912UAG
This fixes reference clock frequency of RB912. 25 MHz frequency leads
to system clock running too fast, uptime incrementing too fast and
delays (like `sleep 10`) returning too early.

Board has quartz with NSK 3KHAA Z 40 000 marking.

Signed-off-by: Pavel Kamaev <pavel@kamaev.me>
2022-10-23 01:45:52 +02:00
David Bentham
67660d3667 ramips: fix WAN mac address allocation for Unielec 01 and 06 models
Manufacturer has predetermined mac address values for lan and wan ports.

This change keeps inline with other mt7621 devices mac address allocation
from factory mtd partition.

Example from hexdump output:

0xe000 0x6 (lan) -           0xe006 0x6 (wan)

0000e000  70 b3 d5 10 02 96 70 b3  d5 10 02 95 ff ff ff ff

Previous change had created an overlapping mac address situation as it
would increment by one based on the lan mac address location found in the
factory partition, which would sometimes increment to the same as the
mt7603 wifi chip.

Tested on Unielec u7621-01 model

Signed-off-by: David Bentham <db260179@gmail.com>
2022-10-23 01:45:52 +02:00
Robert Senderek
ac296f6210 ramips: rt3883: enable lzma-loader for Belkin F9K1109v1
Fixes boot loader LZMA decompression issues

Fixes: #10968
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
2022-10-23 01:45:52 +02:00
Alex Khodin
f6099d7974 ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1
Fixes boot loader LZMA decompression issues.

Without this change the board end up in a boot loop.

Signed-off-by: Alex Khodin <mxktz1@gmail.com>
2022-10-23 01:45:52 +02:00
Chukun Pan
4f9b360f0b ramips: add A-040W-Q alternative name for MSG1500 X.00
The hardware of Nokia A-040W-Q and RAISECOM MSG1500 X.00 are
exactly the same, both of which are customized by operators.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-23 01:45:52 +02:00
Chukun Pan
7b863af180 kernel: move mac-address-ascii patches to generic
This enables other targets to use the mac-address-ascii
feature.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2022-10-23 01:45:52 +02:00
Aleksander Jan Bajkowski
802ca492d8 lantiq: add 6.1 tag to upstream patch
Add 6.1 tag to upstream patch now that 6.1 got tagged. This permits to
track patch in a better way and directly drop them on kernel bump.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-23 01:45:52 +02:00
Martin Blumenstingl
d4571e98ab lantiq: Add Linux 5.15 as testing kernel version
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-22 19:44:46 +02:00
Martin Blumenstingl
d374e0346e lantiq: 5.15: refresh patches
0001-MIPS-lantiq-add-pcie-driver.patch needs to drop
MODULE_SUPPORTED_DEVICE because that macro is gone on newer kernels.

Add checks for copy_{to,from}_user in
0008-MIPS-lantiq-backport-old-timer-code.patch which is now mandatory.

0705-v5.13-net-dsa-lantiq-allow-to-use-all-GPHYs-on-xRX300-and-.patch
get dropped because it's a backport from Linux 5.13.

All other patches are refreshed.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-22 19:44:45 +02:00
Martin Blumenstingl
c783073894 lantiq: copy Linux 5.10 files in preparation for Linux 5.15 support
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-10-22 19:44:45 +02:00
Chen Minqiang
3505933073 ipq40xx: convert to DSA and enable asus,rt-ac42u
This convert board asus,rt-ac42u to DSA and re-enable it

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2022-10-22 20:09:58 +08:00
Hauke Mehrtens
1ea3510c5c kernel: Add missing kernel configuration options
The at91/sam9x targets misses these configuration options when using
kernel 5.15.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
0a00189e41 at91: kernel v5.15: use KERNEL_TESTING_PATCHVER:=5.15
Use KERNEL_TESTING_PATCHVER:=15 for at91 targets.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
dd37b205f8 at91: kernel v5.10: refresh configs
Refresh kernel v5.10 configs.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
fe7e34d793 at91: kernel v5.15: refresh configs
Refresh kernel v5.15 configs.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
d0d7771262 at91: kernel v5.15: remove upstreamed patches
Remove patches that are now integrated in kernel v5.15.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Claudiu Beznea
eb758a8fec at91: kernel v5.15: copy config and patches from 5.10
Copy kernel config and patches from 5.10. Along with it
individual targets' config-default from 5.10 has been moved to
config-5.10.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2022-10-22 00:51:25 +02:00
Daniel Golle
c5c37886cf oxnas: shuttle-kd20: fix thermal zone
Fix typo ('_' vs '-') and add #cooling-cells to gpio-fan to get
thermal zone into functional state.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-21 20:57:53 +01:00
Daniel Golle
63ff5b783d oxnas: switch to Linux 5.15 and drop Linux 5.10
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-21 20:57:53 +01:00
Aleksander Jan Bajkowski
9226f1e419
kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.

Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....

Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
  If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
  option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
  the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC -  enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-21 13:47:01 +02:00
Aleksander Jan Bajkowski
069bda0adb
lantiq: add rgmii delays on BT Home Hub 5A
This comit fixes warnings that occur on kernel 5.15:
...
[    2.269736] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 1e108000.switch-mii:00:
               PHY has delays (e.g. via pin strapping), but phy-mode = 'rgmii'
[    2.269736] Should be 'rgmii-id' to use internal delays txskew:1500 ps rxskew:1500 ps
...

Ref: be393dd685
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-10-21 13:45:37 +02:00
Linus Walleij
e629ced778 bcm53xx: only fixup seama on D-Link DIR-885L
Just one device builds seama images so let's just fix up
seama on that one device. I guess the tool errors out but
this feels cleaner.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[rmilecki: drop "fixtrx" from D-Link case]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-10-21 08:54:34 +02:00
Arınç ÜNAL
2b9bb5b187 bcm53xx: enable Broadcom 4366b1 firmware for Asus RT-AC88U
On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the
4366b1 wireless chip and tries to load the firmware file which doesn't
exist because it's not included in the image.

Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-10-21 08:50:51 +02:00
Daniel Golle
c15e7e2910
mediatek: filogic: consolidate adc '32k' clock
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.

Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-20 20:37:50 +01:00
Petr Štetiar
ae76c978c9 pistachio: refresh kernel patches
Refresh dirty patches after commit 711f1a8bcb ("kernel: mtd: backport
SafeLoader parser").

Fixes: 711f1a8bcb ("kernel: mtd: backport SafeLoader parser")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-20 09:53:23 +02:00
Petr Štetiar
329b583aad ath79: refresh kernel patches
Refresh dirty patches after commit 711f1a8bcb ("kernel: mtd: backport
SafeLoader parser").

Fixes: 711f1a8bcb ("kernel: mtd: backport SafeLoader parser")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-10-20 09:53:23 +02:00
John Audia
b1cc4eac1b
mt7622: switch default CPU governor to ondemand
The most common CPU governor in the OpenWRT project is currently ondemand (see
below).  Switch mt7622 over to it as well.

Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'

ondemand: 16
performance: 5
schedutil: 5
userspace: 2

Build system: x86_64
Build-tested: ramips/mt7621

Signed-off-by: John Audia <graysky@archlinux.us>
2022-10-20 00:44:53 +02:00
Daniel Golle
f2ae4e2f8c
mediatek: clean up platform kernel modules
Remove kmod-sdhci-mtk as the mtk-sd driver is built-in anyway for the
relevant subtargets in order to support mounting rootfs from eMMC or
SD card.

Add kmod-iio-mt6577-auxadc to support reading the raw values from the
auxadc unit used as in-SoC thermal sensor. This driver was previously
built-in, but as thermal itself works well without it there is no use
for it in every day use of a device. Build the module to still allow
access to the raw values for those who need it.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-10-19 23:20:48 +01:00
Andrey Butirsky
47d58afbdf ramips: kndrt31r19: set up wan interface by default
The only WAN port of the device is it's modem, so set it up as such

Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
2022-10-19 23:00:40 +02:00
Mark Mentovai
9a8e008188 ipq40xx: Convert mikrotik,wap-ac to DSA
As done previously, this preserves the MAC addresses of they physical
Ethernet ports. The interfaces are renamed as eth0 is in use for the
native GMAC; the new interface naming matches the physical port labels.
 - sw-eth1 corresponds to the physical port labeled ETH1 and has the
   base MAC address. This port can be used to power the device.
 - sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC
   address one greater than the base.

As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.

Signed-off-by: Mark Mentovai <mark@mentovai.com>
2022-10-19 22:58:12 +02:00
INAGAKI Hiroshi
48bb71ff28 ath79: improve MAC address configuration of ELECOM devices
Get MAC address of WAN from HW.WAN.MAC.Address in hwconfig partition
instead of calculated one from wlan's address.
And added label_mac.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-10-19 22:58:12 +02:00