Specifications:
SoC: MT7621AT
RAM: 128MB
Flash: 16MB NOR SPI flash
WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
LAN: 5x1000M
Firmware layout is Uboot with extra 96 bytes in header
Base PCB is AP-MTKH7-0002
LEDs Power Green,Power Orange,Internet Green,Internet Orange
LEDs "2.4G" Green & "5G" Green connected directly to wifi module
Buttons Reset,WPS,WIFI
Flashing instructions:
Upload image via emergency recovery mode
Push and hold reset button (on the back of the device) until power led
starts flashing (about 10 secs or so) while powering the device on.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1
Use the provided emergency web GUI to upload and flash a new firmware to
the device. Some browsers/OS combinations are known not to work, so if
you don't see the percentage complete displayed and moving within a few
seconds, restart the procedure from scratch and try anoher one,
or try the command line way.
Alternative method using command line on Linux:
curl -v -i -F "firmware=@openwrt-xxxx-squashfs-factory.bin" 192.168.0.1
Signed-off-by: Mathieu Martin-Borret <mathieu.mb@protonmail.com>
[use of generic uimage-padhdr in image generation code]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This creates a common DTSI and shared image definition for the
relatively similar Netgear devices for mt7628 platform.
As a side effect, this raises SPI flash frequency for the R6120,
as it's expected to work there as well if it works for R6080 and
R6020.
Based on the data from the other devices, it also seems probable
the 5g MAC address for R6120 could be extracted from the caldata,
and the mtd-mac-address there could be dropped.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are already two very similar recipes using uimage_padhdr
in ramips target, and a third one is about to be added.
Make the recipe more generic, so redefinitions are not necessary
anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Bjørn Mork <bjorn@mork.no> [Zyxel WAP6805]
The current one only looks for mt76x2e and mt7603e, and
does not work for 2 or more same Wi-Fi chips.
Refactor the script to cover those cases.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
At this point in v5.4 kernel we cannot use dwc2_readl() and
dwc2_writel() since they rely on the value hsotg->needs_byte_swap
which cannot be obtained before the controller wakes up.
We should use readl() and writel() to wake up the controller before
calling dwc2_check_core_endianness().
Fixes: 6be0da90a1 ("ramips: refresh patches")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed Fixes: tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This adds support for the Netgear R6020, aka Netgear AC750.
The R6020 appears to be the same hardware as the Netgear R6080,
aka Netgear AC1000, but it has a slightly different flash layout,
and no USB ports.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
MAC addresses based on vendor firmware:
LAN *:88 0x4
WAN *:89
WLAN2 *:88 0x4
WLAN5 *:8a 0x8004
The factory partition might have been corrupted beforehand. However,
the comparison of vendor firmware and OpenWrt still allowed to retrieve
a meaningful assignment that also matches the other similar devices.
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6020, and power the R6020 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6020-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6020. After flashing has finished,
power cycle the R6020, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Tim Thorpe <timfthorpe@gmail.com>
[slightly extend commit message, fix whitespaces in DTS, align From:
with Signed-off-by]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The rg21s fails to boot if the kernel is larger than about
2,376 KiB. The ra21s is virtually identical hardware.
Enabling lzma-loader resolves the issue on both the rg21s
and ra21s (see FS#3057 on the issue tracker).
Fixes: FS#3057
Signed-off-by: Furkan Alaca <furkan.alaca@queensu.ca>
Device specification:
SoC: RT5350
CPU Frequency: 360 MHz
Flash Chip: Macronix MX25L6406E (8192 KiB)
RAM: Winbond W9825G6JH-6 (32768 KiB)
5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
1x external antenna
UART (J1) header on PCB (57800 8n1)
Wireless: SoC-intergated: 2.4GHz 802.11bgn
USB: None
8x LED, 2x button
Flash instruction:
Configure PC with static IP 192.168.99.8/24 and start TFTP server.
Rename "openwrt-ramips-rt305x-zyxel_keenetic-lite-b-squashfs-sysupgrade.bin"
to "rt305x_firmware.bin" and place it in TFTP server directory.
Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Sergei Burakov <senior.anonymous@ya.ru>
Adding this has been overlooked when rebasing the commit prior to
merge.
Fixes: ba0f4f0cfd ("ramips: add support for TP-Link RE500 v1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: MediaTek MT7621ST
WiFi: MediaTek MT7603
Quantenna QT3840BC
Flash: 128M NAND
RAM: 64M
LED: Dual colour red and green
BTN: Reset
WPS
Eth: 4 x 10/100/1000 connected to MT7621 internal switch
MT7621 RGMII port connected to Quantenna module
GPIO: Power/reset of Quantenna module
Quantenna module
----------------
The Quantenna QT3840BC (or QV840) is a separate SoC running
another Linux installation. It is mounted on a wide mini-PCIe
form factor module, but is connected to the RGMII port of
the MT7621. It loads both a second uboot stage and an os
image from the MT7621 using tftp. The module is configured
using Quantenna specific RPC calls over IP, using 802.1q
over the RGMII link to support multiple SSIDs.
There is no support for using this module as a WiFi device
in OpenWrt. A package with basic firmware and management
tools is being prepared.
Serial ports
------------
Two serial ports with headers:
RRJ1 - 115200 8N1 - Connected to the Quantenna console
J1 - 57600 8N1 - Connected to the MT7621 console
Both share pinout with many other Zyxel/Mitrastar devices:
1 - NC (VDD)
2 - TX
3 - RX
4 - NC (no pin)
5 - GND
Dual system partitions
----------------------
The vendor firmware and boot loader use a dual partition
scheme storing a counter in the header of each partition. The
partition with the highest number will be selected for boot.
OpenWrt does not support this scheme and will always use the
first OS partition. It will reset both counters to zero the
first time sysupgrade is run, making sure the first partition
is selected by the boot loader.
Installation from vendor firmware
---------------------------------
1. Run a DHCP server. The WAP6805 is configured as a client device
and does not have a default static IP address. Make a note of
which address it is assigned
2. tftp the OpenWrt initramfs-kernel.bin image to this address.
Wait for the WAP6805 to reboot.
3. ssh to the OpenWrt initramfs system on 192.168.1.1. Make a
backup of all mtd partitions now. The last used OEM image is
still present in either "Kernel" or "Kernel2" at this point,
and can be restored later if you save a copy.
4. sysupgrade to the OpenWrt sysupgrade.bin image.
Installation from U-Boot
------------------------
This requires serial console access
1. Copy the OpenWrt initramfs-kernel.bin image as "ras.bin" to
your tftp server directory. Configure the server address as
192.168.0.33/24
2. Hit ESC when the message "Hit ESC key to stop autoboot"
appears
3. Type "ATGU" + Enter, and then "2" immediately after pressing enter.
4. Answer Y to the question "Erase Linux in Flash then burn new
one. Are you sure?", and answer the address/filename questions.
Defaults:
Input device IP (192.168.0.2)
Input server IP (192.168.0.33)
Input Linux Kernel filename ("ras.bin")
5. Wait until after you see the message "Done!" and power cycle
the device. It will hang after flashing.
6. Continue with step 3 and 4 from the vendor firmware procedure.
Notes on the WAP6805 U-Boot
---------------------------
The bootloader has been modified with both ZyXELs zyloader and the
device specific dual partition scheme. These changes appear to have
broken a few things. The zyloader shell claims to support a number
of ZyXEL AT commands, but not all of them work. The image selection
scheme is unreliable and inconsistent. A limited U-Boot menu is
available - and used by the above U-Boot install procedure. But
direct booting into an uploaded image does not work, neither with
ram nor with flash. Flashing works, but requires a hard reset after
it is finished.
Reverting to OEM firmware
-------------------------
The OEM firmware can be restored by using mtd write from OpenWrt,
flashing it to the "Kernel" partition. E.g.
ssh root@192.168.1.1 "mtd -r -e Kernel write - Kernel" < oem.bin
OEM firmwares for the WAP6805 are not avaible for public download,
so a backup of the original installation is required. See above.
Alternatively, firmware for the WAP6806 (Armor X1) may be used. This
is exactly the same hardware. But the branding features do obviously
differ.
LED controller
--------------
Hardware implementation is unknown. The dual-color LED is controlled
by 3 GPIOs:
4: red
7: blinking green
13: green
Enabling both red and green makes the LED appear yellow.
The boot loader enables hardware blinking, causing the green LED to blink
slowly on power-on, until the OpenWrt boot mode starts a faster software
blink.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[fix alphabetic sorting for image build statement]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"
See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg
Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot
Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo
Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client
1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0
other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)
MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004
Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 128MB
FLASH: 16MB NOR (Macronix MX25L12805D)
ETH: 1x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615 (4x4:4)
- 5GHz: 1x MT7615 (4x4:4)
- 4 antennas: 2 external detachable and 2 internal
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x Green led (Power)
- 1x Green-Amber-Red led (Wifi)
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the factory image directly from OEM web interface.
(You can login using these credentials: admin/1234)
Restore OEM Firmware
--------------------
Flash the OEM "bin" firmware directly from LUCI.
The firmware is downloadable from the OEM web page.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Restoring procedure tested with RE23_1.08.bin
MAC addresses
-------------
factory 0x4 *:24
factory 0x8004 *:25
Cimage 0x07 *:24
Cimage 0x0D *:24
Cimage 0x13 *:24
Cimage 0x19 *:25
No other addresses were found in factory partition.
Since the label contains both the 2.4GHz and 5GHz mac address I decided
to set the 5GHz one as label-mac-device. Moreover it also corresponds
to the lan mac address.
Notes
-----
The wifi led in the OEM firmware changes colour depending on the signal
strength. This can be done in OpenWrt but just for one interface.
So for now will not be any default action for this led.
If you want to open the case, pay attention to the antenna placed on
the bottom part of the front cover.
The wire is a bit short and it breaks easily. (I broke it)
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[fix two typos and add extended MAC address section to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves WiFi LED triggers from 01_leds to device tree.
While at it, convert the labels there to lower case; this is
more commonly used and the change will actually remove competition
between DT trigger and leftover uci config on already installed
systems.
Suggested-by: Georgi Vlaev <georgi.vlaev@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reduce spi-max-frequency for ipTIME A8004T and disable
m25p,fast-read option.
A8004T uses `en25qh128` for the MTD.
This flash memory would allow 80MHz, sometimes kernel received
wrong id value in initramfs installed router.
(kernel expected `1c 70 18 1c 70 18`, but one of cases, it
was `9c 70 18 1c 70 18`)
In this case, openwrt can't detect the partition information,
it would write the inccorect data to the firmware partition and
also it would occur the bootlooping after sysupgrade.
Signed-off-by: Sunguk Lee <d3m3vilurr@gmail.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes:
- CVE-2020-10757
The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was
backported which needed some adaptations to other code.
Build tested: ramips
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Signed-off-by: Rowan Border <rowanjborder@gmail.com>
Cudy WR1000 and Wavlink WL-WN577A2 store WAN as well as label MAC address
at the same position in flash.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: David Bauer <mail@david-bauer.net>
This package allows to read battery status information and control the
power state of the RAVPower RP-WD009 power management IC.
Signed-off-by: David Bauer <mail@david-bauer.net>
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.
Hardware
--------
CPU: MediaTek MT7628AN
RAM: 64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN: MediaTek MT7628AN 2T2R b/g/n
MediaTek MT7610E 1T1R n/ac
ETH: 1x FastEthernet
SD: SD Card slot
USB: USB 2.0
Custom PMIC on the I2C bus (address 0x0a).
Installation
------------
1. Press and hold down the reset button.
2. Power up the Device. Keep pressing the reset button for 10
more seconds until the Globe LED lights up.
3. Attach your Computer to the Ethernet port. Assign yourself the
address 10.10.10.1/24.
4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
factory image.
5. The flashing will take around 1 minute. The device will reboot
automatically into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the Wavlink WL-WN577A2 (black case) dual-band
wall-plug wireless router. In Germany this device is sold under the brand
name Maginon WL-755 (white case):
Device specifications:
- CPU: MediaTek MT7628AN (580MHz)
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 2x 10/100 Mbps (Ralink RT3050)
- 2.4 GHz: 802.11b/g/n SoC
- 5 GHz: 802.11a/n/ac MT7610E
- Antennas: internal
- 4 green LEDs: 1 programmable (WPS) + LAN, WAN, POWER
- Buttons: Reset, WPS
- Small sliding power switch
Flashing instructions (U-boot):
- Configure a TFTP server on your PC/Laptop and set its IP
to 192.168.10.100
- Rename the OpenWrt image to firmware.bin and place it in the
root folder of the TFTP server
- Power off (using the small sliding power switch on the left
side) the device and connect an ethernet cable from its LAN
or WAN port to your PC/Laptop
- Press the WPS button (and keep it pressed)
- Power on the device (using the small power switch)
- After a few seconds, when the WAN/LAN LED stops blinking
very fast, release the WPS button
- Flashing OpenWrt takes less than a minute, system will
reboot automatically
- After reboot the WPS LED will indicate the current OpenWrt
running status
Signed-off-by: Lars Wessels <software@bytebox.org>
[removed unused labels - fix whitespace errors - wrap commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The WAC124 hardware appears to be identical to R6260/R6350/R6850.
SoC: MediaTek MT7621AT
RAM: 128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 nac 4T4R
ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB: 1x USB 2.0
BTN: Reset, WPS
LED: Power, Internet, WiFi, USB (all green)
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This adds support for the Netgear R6080, aka Netgear AC1000.
The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.
Signed-off-by: Qin Wei <support@vocore.io>
chosen/bootargs are defined to the same value in device DTS files
that is already set in the SoC DTSI. Remove the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
This moves the trigger for the Netgear R6120's wlan2g_green LED from
base-files/etc/board.d/01_leds to the device-tree file.
This has been applied to R6120 based on findings for the very similar
Netgear R6080.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[merge case in 01_leds, slightly adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
Fixes: dfd62e575c ("ramips: enable packet steering by default on mt7621")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With the new driver, MAC addresses are not set up in DTS anymore,
and therefore label-mac-device will be useless there.
Setup is done properly in 02_network, so this just removes the
obsolete alias.
Fixes: 5e50515fa6 ("ramips/mt7621: mikrotik: don't use
mtd-mac-address in DTS")
Suggested-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This updates the display port order for the TEW-810DR to be in line
with the DIR-810L. Both share the same board and pictures on the
vendors' pages indicate the same external numbering scheme as well.
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[replace commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
NETGEAR WAC104 is an AP based on castrated R6220, without WAN
port and USB.
SoC: MediaTek MT7621ST
RAM: 128M DDR3
FLASH: 128M NAND
WiFi: MediaTek MT7612EN an+ac
MediaTek MT7603EN bgn
ETH: MediaTek MT7621ST (4x LAN)
BTN: 1x Connect (WPS), 1x WLAN, 1x Reset
LED: 7x (3x GPIO controlled)
Installation:
Login to netgear webinterface and flash factory.img
Back to stock:
Use nmrpflash to revert stock image.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The port order displayed in LuCI is currently inverted for this
devices:
LuCI - Device
LAN1 - LAN4
LAN2 - LAN3
LAN3 - LAN2
LAN4 - LAN1
Fix it.
Strangely, the owner of a TRENDnet TEW-810DR reports that the
initial port order is correct, while both devices share the
same board and look similar from the outside. Since I cannot
investigate this without having any of the devices, this does
only touch the DIR-810L for now.
While at it, also merge in the case for zbtlink,zbt-we2026, as
the display port specified for WAN there won't have any effect
anyway.
Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The WAN LED on DIR-810L was actually blinking on LAN1 port
activity. This has already been improved for the TEW-810DR, where
the GPIO has been set up explicitly rather than having it controlled
by the switch.
This patch also applies this setup to the DIR-810L.
In addition, the trigger in 01_leds is set up with
ucidef_set_led_switch for both devices now, so state changes should
be displayed correctly as well.
Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L]
Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
Since 01_enable_packet_steering only touches the network config,
limit the uci commit to this as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to the manual, the amber power LED is used to indicate boot,
while the green LED is meant to indicate a running system.
While at it, also adjust the DT node names for all LEDs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
* SoC: MT7620A
* CPU: 580 MHz
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The device is identical to the EX6130 except
for the mains socket and the hardware ID.
Installation:
The -factory images can be flashed from the
device's web interface or via nmrpflash.
Notes:
MAC addresses were set up based on the EX6130 setup.
This is based on prior work of Adam Serbinski and Mathias Buchwald.
Tested by Mathias Buchwald.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This partially reverts commit 5acd1ed0be ("ramips: mt7621: fix
Ubiquiti ER-X ports names and MAC addresses"), this change was discussed
in https://github.com/openwrt/openwrt/pull/2901#discussion_r407238452
With commit 5acd1ed0be ("ramips: mt7621: fix Ubiquiti ER-X ports names
and MAC addresses"), all the ports were put into the LAN bridge, with
the argument that the OEM firmware does not have a WAN port enabled. In
the default OEM setup, all of the ports except eth0 are dead and eth0 is
set to a static IP address without providing DHCP services when
connected. It is only after the wizard has been run that eth0 becomes
the WAN port and all the rest of the ports belong to LAN with DHCP
enabled.
Having all of the ports set to the LAN bridge does not mirror the default
OEM setup. To accomplish that, then only eth0 would be in the LAN bridge.
But this is not the expected behaviour of OpenWrt.
Therefore this proposal to set eth0 to WAN and eth1-N to LAN provides
the expected behaviour expected from OpenWrt, maintains the current
documentation as up-to-date, and does not require the user to manually
detach eth0 from the LAN bridge, create the WAN(6) interface(s), and set
eth0 to the WAN(6) interface(s).
Fixes: 5acd1ed0be ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses")
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
[commit subject and description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Previously the dts were using a value determined by empirical testing,
because of a spi driver/clock bug. The bug was fixed quite some time
ago. 33 MHz is the default clock frequency used by RouterBOOT and thus
safe.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.
Removed:
- 0032-USB-dwc2-add-device_reset.patch
Fixes: FS#2738
Fixes: FS#2964
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
Specifications:
* MediaTek MT7620A (580 Mhz)
* 8 MB of FLASH
* 64 MB of RAM
* 2.4Ghz and 5.0Ghz radios
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* UART header on PCB (57600 8n1)
* Green/Orange Power LEDs illuminating a Power-Button Lens
* Green/Orange Internet LEDs GPIO controlled illuminating a Globe/Internet Lens
* 3x button - wps, power and reset
* U-boot bootloader
Installation:
The sysupgrade.bin image is reported to be OEM web flashed with an ncc_att_hwid
appended. ncc_att_hwid is a 32bit binary in the GPL Source download for either
the TEW-810DR or DIR-810L and is located at
source/user/wolf/cameo/ncc/hostTools.
The invocation is: ncc_att_hwid -f tew-810dr-squashfs-factory.bin -a -m "TEW-810DR" -H "1.0R" -r "WW" -c "1.0"
This may need to be altered if your hardware version is "1.1R".
The image can also be directly flashed via serial tftp:
1. Load *.sysupgrade.bin to your tftp server directory and rename for
convenience.
2. Set a static ip 192.168.10.100.
3. NIC cable to a lan port.
4. Serial connection parameters 57600,8N1
5. Power on the TEW-810 and press 4 for a u-boot command line prompt.
6. Verify IP's with U-Boot command "printenv".
7. Adjust tftp settings if needed per the tftp documentation
8. Boot the tftp image to test the build.
9. If the image loads, reset your server ip to 192.168.1.10 and restart network.
10. Log in to Luci, 192.168.1.1, and flash the *sysupgrade.bin image.
Notes:
The only valid MAC address is found in 0x28 of the factory partition.
Other typical offsets/caldata only contain example data: 00:11:22:00:0f:xx
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
[remove "link rx tx" in 01_leds, format and extend commit message,
fix DTS led node names]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- MT7628NN @ 580 MHz
- 32 MB RAM
- 8 MB Flash
- 5x 10/100 Mbps Ethernet (built-in switch)
- 2.4 GHz WLAN
- 2x external, non-detachable antennas (1x for RT-N10P V3)
Flash instructions:
1. Set PC network interface to 192.168.1.75/24.
2. Connect PC to the router via LAN.
3. Turn router off, press and hold reset button, then turn it on.
4. Keep the button pressed till power led starts to blink.
5. Upload the firmware file via TFTP. (Any filename is accepted.)
6. Wait until the router reboots.
Signed-off-by: Ernst Spielmann <endspiel@disroot.org>
[fix node/property name for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit f761f4052c had bogus case syntax, the uci-defaults script threw
errors as a result and exited non-zero, probably didn't do what was
intended, but tried over and over since the non-zero exit prevents the
script from being deleted.
Fixes: f761f4052c ("ramips: mt7621: harmonize naming scheme for Mikrotik")
Signed-off-by: Russell Senior <russell@personaltelco.net>
[extend commit title, add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot
Installation:
1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0
Restore to stock:
1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white
Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.
Exploit and detailed instructions:
https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100
An implementation of CVE-2020-8597 against stock firmware version 1.0.14
This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.
As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.
The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh
Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Olimex RT5350F-OLinuXino devices do not have a default MAC address, and there is
nothing at the 0x4 offset in the factory partition. Using a local address, which
is randomly generated by the kernel, would be a better choice.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
of_get_mac_address can return ERR_PTR since 5.2, so the return pointer should be
checked before used. Otherwise it might cause an oops during boot.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This is additional fix of c998ae7f0e.
The sysupgrade image of I-O DATA MT7621 devices manufactured by MSTC
(MitraStar Technology Corp.) faced to the booting issue. This was caused
by imcomplete extraction of large kernel image by U-Boot, and this issue
is occurred in initramfs image after fixing of sysupgrade image.
So, use lzma-loader for initramfs image to fix the issue.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
ramips images now relies on explicit switch setup for proper failsafe
functionality. Remove default cases where it relies on vlan setup in
dts and add switch setup for devices affected.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The location 0x28 in factory partition is the common one used for
ethernet address on this architecture. Despite, it contains the label
MAC address for the devices at hand.
Consequently, this patch moves 0x28 to the ðernet node in DTS files
(setting the WAN MAC address there) and sets up the lan_mac from 0x22
in 02_network. As a benefit, this allows to use label-mac-device in
DTS instead of ucidef_set_label_macaddr.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like for the RT-AC54U, this uses a DT trigger for WiFi also at the
RT-AC51U. While at it, rename node and label to wifi2g.
Note that the 5g WiFi LED still isn't supported (see PR #3017 for
further details: https://github.com/openwrt/openwrt/pull/3017 )
Tested-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current MAC address assignment for the ASUS RT-AC51U is "wrong",
it actually should be the same as for the RT-AC54U. Fix it.
MAC assignment based on vendor firmware:
2g 0x4 label
5g 0x8004 label +4
lan 0x22 label +4
wan 0x28 label
Thanks to Davide Fioravanti for checking this on his device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The version inside the compat file determines, if a firmware supports
a specific device. I have not yet fully understood, how this is checked,
but it only seems to indicate which devices are supported by a specific
version of the combined vendor firmware. Devices assume that subsequent
versions, starting with the version that initially added support for a
specific device, are always compatible.
The first compat version that added support for the EP-R6 was '21001:7',
but OpenWrt did use '21001:6' before. This is why the factory image could
not be flashed using the vendor software, but only using TFTP.
The compat version has been bumped by the vendor a few times, but more
devices have been added since (e.g. ER-10X). Because OpenWrt currently
only supports the ER-X, ER-X-SFP and EP-R6, the compat version is
incremented to the version that first supported the EP-R6, which is
'21001:7'.
This allows the factory image to be flashed on EP-R6 without TFTP.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
This increases the SPI frequency for both ASUS RT-AC51U and RT-AC54U.
Speed comparison tests have been performed on RT-AC54U:
- 10Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 4m 37.78s
user 0m 0.02s
sys 2m 43.92s
- 50Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 1m 28.34s
user 0m 0.03s
sys 0m 46.96s
- 50Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 1m 11.94s
user 0m 0.01s
sys 0m 46.94s
- 80Mhz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 1m 12.31s
user 0m 0.04s
sys 0m 46.96s
- 80Mhz fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 1m 12.15s
user 0m 0.02s
sys 0m 46.97s
Based on that, we took 50 MHz with fast-read, as higher frequencies
didn't yield further improvements.
For the RT-AC51U, only the final configuration was tested.
Tested-by: Zhijun You <hujy652@gmail.com> [RT-AC54U]
Tested-by: Davide Fioravanti <pantanastyle@gmail.com> [RT-AC51U]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.
Hardware
--------
SoC: Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM: 256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH: 5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
- 2.4GHz: 1x MT7615N (4x4:4)
- 5GHz: 1x MT7615N (4x4:4)
- 4 antennas: 3 external detachable antennas and 1 internal
USB:
- 1x USB 3.0
- 1x USB 2.0
BTN:
- 1x Reset button
- 1x WPS button
LEDS:
- 1x White led (Power)
- 6x Green leds (link lan1-lan4, link wan, wps)
- 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)
Everything works correctly.
Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.
However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).
After this, you should be back in the OEM firmware.
Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).
When the router reboots flash the “factory” OpenWrt image and this
time it should work.
After the OpenWrt installation you have to use the sysupgrade image
for future updates.
Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.
Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
1) "kernel" and "rootfs"
2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.
This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.
A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.
Another way to switch the boot partition is:
1) power on the router
2) wait 15 seconds
3) power off the router
4) repeat steps 1-2-3 twice more.
5) power on the router and you should be in the “other” firmware
In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.
Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.
However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.
If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
netis WF2770 is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: MT7530BU
- UART:
- J2: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
MAC addresses in factory partition:
0x0004: LAN, WiFi 2.4GHz (label_mac-6)
0x0028: not used (label_mac-1)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac+2)
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Specification:
- CPU: MTK MT7620A
- RAM: 64MB
- ROM: 16MB SPI Flash Macronix MX25L12835E
- WiFi1: MediaTek MT7620A
- WiFi2: MediaTek MT7612E
- Button: reset, wps
- LED: 9 LEDs:Power, WiFi 2.4G,WiFi 5G, USB, LAN1, LAN2, LAN3, LAN4, WAN
- Ethernet: 5 ports, 4 LAN + 1 WAN
- Other: 1x UART 1x USB2.0
Installation:
Update using ASUS Firmware Restoration Tool:
1. Download the ASUS Firmware Restoration Tool but don't open it yet
2. Unplug your computer from the router
3. Put the router into Rescue Mode by: turning the power off, using a pin
to press and hold the reset button, then turning the router back on while
keeping the reset button pressed for ~5 secs until the power LED starts
flashing slowly (which indicates the router has entered Rescue Mode)
4. Important (if you don't do this next step the Asus Firmware
Restoration Tool will wrongly assume that the router is not in Rescue Mode
and will refuse to flash it): go to the Windows Control Panel and
temporarily disable ALL other network adapters except the one you will use
to connect your computer to the router
5. For the single adapter you left enabled, temporarily give it the
static IP 192.168.1.10 and the subnet mask 255.255.255.0
6. Connect a LAN cable between your computer (make sure to use the
Ethernet port of the adapter you've just set up) and port 1 of the router
(not the router's WAN port)
7. Rename sysupgrade.bin to factory.trx
8. Open the Asus Firmware Restoration Tool, locate factory.trx and click
upload (if Windows shows a compatibility prompt, confirm that the tool worked fine)
9. Flashing and reboot is finished when the power LED stops blinking and
stays on
MAC assignment based on vendor firmware:
2g 0x4 label
5g 0x8004 label +4
lan 0x22 label +4
wan 0x28 label
Signed-off-by: Zhijun You <hujy652@gmail.com>
[rebased due to DTSI patch, minor commit message adjustments, fix
label MAC address (lan->wan), do spi frequency increase separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This creates a DTSI for the ASUS RT-AC51U and the upcoming RT-AC54U,
as they are quite similar.
White at it, drop the unneeded "status = okay" for ethernet.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The property "ralink,port-map" has been obsolete long before
this device was added, and the device is a one-port anyway.
Just remove it.
Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This tidies up the ethernet node in mt7620 DTS files by:
- removing unnecessary status as it is not disabled
- reordering properties consistently
- adding empty lines to enhance readability
This should make comparison and reviewing new PRs based on C/P easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The BL-W1200 Wireless Router is based on the MT7620A SoC.
Specification:
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612E)
- 5x 10/100/1000 Mbps Ethernet (MT7530)
- 2x external, non-detachable antennas (Wifi 2.4G/5G)
- 1x USB 2.0
- UART (R2) on PCB (57600 8n1)
- 9x LED (1 GPIO controlled), 1x button
- u-Boot bootloader
Known issues:
- No status LED. Used WPS LED during boot/failsafe/sysupgrade.
Installation:
1. Apply initramfs image via factory web-gui.
2. Install sysupgrade image.
How to revert to OEM firmware:
- sysupgrade -n -F stock_firmware.bin
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Most work was done in commit 021c893658 ("ramips: fix size-cells on spi
nodes"), but a few more DTS files using the old reg style have been added
since then. This commit fixes them.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
- use tab indent in image build recipes for consistency
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[use different line wrapping for one recipe]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As the node is already defined and labeled in SoC DTSI file, we can refer to it
outside of root node and reduce redundancy.
While at it, remove unused pcf8563 label.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Change "0" to "0x0" for consistency. This is an extension of commit 34abfb6e91
("ramips: convert mediatek,mtd-eeprom from decimal to hex notation").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
As evidenced here[1] the device MAC address can be stored at a random
offset in the hard_config partition. Rely on sysfs to update the MAC
address correctly.
Adjust config so that WAN is base MAC and LAN is base MAC +1 to better
match label and vendor OS.
[1] https://github.com/openwrt/openwrt/pull/2850#issuecomment-610809021
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
This reverts commit a1693bf626.
The rt288x and rt3883 devices in question don't have switches.
Only keep the merged case for rt305x.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.
Fix the MAC addresses in OpenWrt.
Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.
Remove the redundant inclusions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 8f6334eb94 ("ramips: explicitly disable built-in switch when needed")
did not fix rt288x and rt3883 devices. This patch deals with them.
While at it, consolidate duplicate cases in interface setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Note:
These devices use Z-LOADER to read the kernel from NAND flash and boot
it. Z-LOADER cannot load and start plain lzma-loader, so additional
lzma-compression is needed.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.
Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.
Factory image sizes (commit: 5f126c541a) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default): 4784188 bytes, LZMA ERROR 1
- with "-d19": 4915260, LZMA ERROR 1
- with "-d18": 4915260, diff to original: +128 KB
- with "-d17": 4980796, diff to original: +192 KB
- with this patch: 4849724, diff to original: +64 KB
To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.
The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!
[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.
Fixes: c2334ad60d ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.
Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.
With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.
NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!
Signed-off-by: René van Dorst <opensource@vdorst.com>
mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their
DTS(I) files are incompatible to kernel 4.14.
Remove the corresponding kernel config files to signal that more
boldly and to prevent accidentally patching the wrong kernel when
pulling in older config patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Netgear R7200 is another clone of Netgear R6700v2, introduced in:
6e80df5 ("ramips: add support for NETGEAR R6700v2/AC2400")
Reported-by: Joel Pinsker, github user @joelp64
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The pinctrl driver had been replaced with the upstream one in b756ea2a90
("ramips: replace pinctrl property names"), but the initial A1004ns support
patch did not reflect the changes. This commit updates its pinctrl property
names.
Fixes: 9169482f64 ("ramips: add support for ipTIME A1004ns")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt7621 overrides KERNEL_DTB to limit dictionary size, which isn't needed
for our lzma loader.
This saves 15KB on mt7621 devices using uimage-lzma-loader.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit increases the hardware SPI frequency from 24.2MHz to 48.3MHz.
[ 5.314163] m25p80 spi0.0: speed: 24166666/40000000, rate: 8, prescal: 2, loops: 226
[ 5.076323] m25p80 spi0.0: speed: 48333333/50000000, rate: 4, prescal: 1, loops: 162
`time cat /dev/mtd2 >/dev/null` is reduced from 5.64s to 4.36s on A104ns,
and from 11.39s to 8.81s on A1004ns.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.
Signed-off-by: René van Dorst <opensource@vdorst.com>
With v5.4 kernel a new gpio driver is used.
GPIO numbering has changed so update 03_gpio_switches too.
Signed-off-by: René van Dorst <opensource@vdorst.com>
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Increase kernel partition because 2M is insufficient for 5.4
Because the partition changes, previous version of OpenWrt cannot upgrade
to this version, and requires a new installation
Recovery to stock instruction:
1. Download stock firmware at
http://ur.ikcd.net/HC5962-sysupgrade-20171221-b00a04d1.bin
2. Power off the router
3. Press and hold the reset button for 4~6 sec while power it back on
4. Connect a PC to router's LAN
5. Visit http://192.168.2.1 and upload the firmware
Then repeat the instruction in edae3479e6 to install OpenWrt
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
ubnt er-x/xiaomi/netgear sercomm devices are known to have troble
extracting a big kernel from flash and has support for uncompressed
uimage
This commit uses uncompressed uimage with lzma-loader for these devices
to fix boot issue.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Some devices have bootloaders with broken lzma code resulting in failed
decompression or corrupted kernel code.
This image recipe allows to sacrifice 5KB for OpenWrt LZMA loader and
take over the task of decompress kernel.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Loader platform is a per-soc variable instead of a per-device one.
Determine corresponding loader platform at the beginning of image
Makefile.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Upstream pinctrl driver in drivers/staging uses
groups/function/ralink,num-gpios instead of
ralink,group/ralink,function/ralink,nr-gpio
Replace these properties in dts as well as the pinctrl driver in
patches-4.14.
This commit is created using:
sed -i 's/ralink,group/groups/g'
sed -i 's/ralink,function/function/g'
sed -i 's/ralink,nr-gpio/ralink,num-gpios/g'
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
previously we rely on the failsafe setup in preinit scripts to disable
built-in switch implicitly for single-port devices. This doesn't work
anymore due to preinit script removal.
this patch explicitly disable built-in switch for needed devices.
Fixes: a8d62a4eb1 ("ramips: remove set_preinit_iface script")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
default initramfs for 5.4 kernel is larger than 4M, causing build error
for oversized initramfs image.
disable these images because we have no mechanism for ignoring initramfs
errors and the squashfs image will be larger than initramfs anyway.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
upstream driver merged 3 separated gpio banks into one gpio node.
and gpioX Y in our local driver should be replaced with gpio X*32+Y.
This patch is created using the following sed command:
sed -i -r 's/(.*)gpio([0-9]) ([0-9]+)(.*)/echo "\1gpio $((\2*32+\3))\4"/ge'
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This hack is needed for old ethernet driver:
On mt7620, we have two exposed RGMII ports that connects to builtin
switch. However, swconfig has no way to interact with phy subsystem.
As a result, we have to register both PHYs to ethernet mac instead
and this patch prevents main ethernet interface from going down due
to phy link changes.
Also rename the patch for its actual purpose.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
increase spi frequency for both devices to 45MHz.
while at it, also remove m25p,fast-read for newifi d1 as it's only
needed when spi clock is higher than 50MHz.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
These are boards known to start on 3-byte address mode, which requires
broken-flash-reset if 4B_OPCODES isn't supported by the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Instead of resetting flash to 3B address on remove hook, this
implementation only enters 4B mode when needed, which prevents more
unexpected reboot stuck. This implementation makes it only break when
a kernel panic happens during flash operation on 16M+ areas.
Also silent broken-flash-reset warning. We are not dealing with vendors
and it's unpleasant for users to see that unnecessary and long WARN_ON
print.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The "proper" vendor prefix for Ubiquiti is "ubnt", this is used in
all targets except ramips and also recommended by the kernel.
This patch adjusts the various board/image/device name variables
accordingly. Since we touch it anyway, this also adds the space
in "EdgeRouter X" as a hyphen to those variables to really make
them consistent with the model name.
While at it, create a real shared definition for the devices in
image/mt7621.mk instead of deriving one device from another.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
I-O DATA WN-AX2033GR is roughly the same as I-O DATA
WN-AX1167GR2. The difference is Wi-Fi feature.
Specification
=============
- SoC: MediaTek MT7621A
- RAM: DDR3 128 MiB
- Flash Memory: NAND 128 MiB (Spansion S34ML01G200TF100)
- Wi-Fi: MediaTek MT7603E
- Wi-Fi: MediaTek MT7615
- Ethernet: 5x 10 Mbps / 100 Mbps / 1000 Mbps (1x WAN, 4x LAN)
- LED: 2x green LED
- Input: 2x tactile switch, 1x slide switch
- Serial console: 57600bps, PCB through hole J5 (Vcc, TX, RX, NC, GND)
- Power: DC 12V
This device only supports channel 1-13 and 36-140.
Thus, narrower frequency limits compared to other devices are required
for limiting wi-fi frequency correctly.
Without this, non-supported frequencies are activated.
Flash instructions
==================
1. Open the router management page (192.168.0.1).
2. Update router firmware using "initramfs-kernel.bin".
3. After updating, run sysupgrade with "sysupgrade.bin".
Recovery instructions
=====================
WN-AX2033GR contains Zyxel Z-LOADER
1. Setup TFTP server (IP address: 10.10.10.3).
2. Put official firmware into TFTP server directory (distribution site:
https://www.iodata.jp/lib/software/w/2068.htm)
3. Connect WX-AX2033GR Ethernet port and computer that runs TFTP server.
4. Connect to serial console.
5. Interrupt booting by Esc key.
6. Flash firmware using "ATNR 1,[firmware filename]" command.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
[adjust for kernel 5.4, add recovery instructions/frequency comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds missed line in 01_leds and fix error:
"/bin/board_detect: /etc/board.d/01_leds: line 93:
syntax error: unexpected ")" (expecting ";;")"
Fixes: c948a47 ("ramips: add support for D-Link DWR-960")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
ZyXEL Keenetic has 8MB flash, but OpenWrt uses only 4MB.
This commit fixes the problem.
WikiDevi page [1] says that ZyXEL Keenetic has FLA1: 8 MiB, there is
an article with specs [2] (in Russian).
[1] https://wikidevi.wi-cat.ru/ZyXEL_Keenetic
[2] https://3dnews.ru/608774/page-2.html
Fixes: FS#2487
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
At this moment mt7620 ethernet driver doesn't support rgmii delays
configuration. SoC MT7620 have bits 2 and 3 in GPC1 an GPC2 to configure
delays for rx and tx rgmii interface.
This patch adds rx/tx rgmii delay configuration from dts.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
So far, image/device/board names for Mikrotik devices in mt7621 have
been used quite inconsistently.
This patch harmonizes the naming scheme by applying the same style
as used lately in ath79, i.e. using "RouterBOARD" as separate word
in the model name (instead of RB prefix for the number) and deriving
the board/device name from that (= make lower case and replace spaces
by hyphens).
This style has already been used for most the model/DEVICE_MODEL
variables in mt7621, so this is essentially just adjusting the remaining
variables to that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Buffalo WSR-2533DHPL is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 128 MiB
- Flash : SPI-NOR 16 MiB
- WLAN : 2.4/5 GHz 4T4R (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (3x buttons, 2x slide-switches)
- UART : through-hole on PCB
- J4: 3.3V, GND, TX, RX from triangle-mark
- 57600n8
- Power : 12VDC 1.5A
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
5. wait ~120 seconds to complete flashing
Switch position overview:
- slide-switch1 (2x positions)
- "AUTO"
- "MANUAL" (not connected to gpio)
- slide-switch2 (3x positions)
- "ROUTER"
- "AP" (not connected to gpio)
- "WB"
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note on switches, fix group->groups for state_default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes the node names for the LEDs in the Netgear R6120
device-tree file to provide consistency with other devices.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DSA requires master netdev to be up before any of its slave ports.
Bring it up during preinit so that the first lan port can be used
on failsafe.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
LAN ports of MTC WR1201 are reversed, so correct their names
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".
The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4
Since we have switched to DSA, it's possible to use different MAC for each port.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Most of MT7621 boards have LAN1~4 and WAN, so make this as the default
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Acked-by: Jo-Philipp Wich <jo@mein.io>
[split commit]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
There's different gpio and ethernet drivers upstream for mt7621.
Update these two nodes to match upstream dt bindings.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Since commit f8c55dc ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.
So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The root file system is getting too big for this device and this breaks
the ramips/rt305x build.
Do not build images for this board by default to fix this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Currently kmod-i2c-* will not get into images unless kmod-i2c-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-hwmon-lm75
- kmod-i2c-gpio
- kmod-i2c-gpio-custom
- kmod-i2c-mux
- kmod-i2c-ralink
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TOTOLINK A3 is a clone of ipTIME A3. The only difference is the model name.
Specifications:
- SoC: MT7628AN
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7612EN
- Ethernet: 3x 10/100Mbps
- Switch: SoC internal
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Tested on device by JasonHCH <hsuan670629@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Currently kmod-ata-* will not get into images unless kmod-ata-core is added to
DEVICE_PACKAGES as well. By changing the dependencies from "depends on" to
"select", we do not have the issue anymore.
Furthermore, we can remove most occurrences of the package from DEVICE_PACKAGES
and similar variables, as it is now pulled by dependent modules such as:
- kmod-ata-ahci
- kmod-ata-ahci-mtk
- kmod-ata-sunxi
While at it, use AddDepends/ata for kmod-ata-pdc202xx-old.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Hardware
--------
SoC: MediaTek MT7621AT
WiFi: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 ac 4T4R
Flash: 32M SPI (Macronix MX25L25635F)
RAM: 128M DDR3 (Winbond W631GG6KB)
LED: Dome (Blue / White)
BTN: Reset
Installation
------------
These instructions were written for firmware version v3.9.27.
Downgrade if necessary.
1. Copy the OpenWrt sysupgrade image to the devices /tmp folder
via scp. On factory defaults, user and password is "ubnt" at
192.168.1.20/24.
2. Write the bootselect flag. Otherwise, the device might boot from the
wrong partition. Verify the mtd partition used in the command below
is the one labled "bs" in /proc/mtd (as this might change in the
future).
> dd if=/dev/zero bs=1 count=1 of=/dev/mtd4
3. Write the OpenWrt sysupgrade to the mtd partitions labled
"kernel0" and "kernel1".
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock6
> dd if=/tmp/openwrt-sysupgrade.bin of=/dev/mtdblock7
4. Reboot or powercycle the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SoC: MediaTek MT7620A
RAM: 64MB
FLASH: 8MB SPI
WLAN: 2G: MediaTek MT7620A
5G: MediaTek MT7610EN
ETH: 1x 10/100/1000M (Atheros AR8035)
LED: RSSI (orange/green)
WiFi 2G (green)
WiFi 5G (green)
Power (green)
System (red / green)
BTN: Power
Reset
LED
WPS
Serial
------
P1 - Tx
P2 - Rx
P3 - GND
P4 - VCC
Pin 4 is the one closest to the LAN port.
MAC overview
------------
WAN *:4c uboot 0x1fc00
2.4 *:4c uboot 0x1fc00
5 *:4e uboot 0x1fc00 +2
Installation
------------
Web interface:
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial/TFTP:
You can use initramfs for booting via RAM or flash the image directly.
Additional Notes:
If the web interface upgrade fails, you have to open your device and
attach serial console. Since the web upgrade overwrites the boot loader,
you might also brick your device.
In order to flash back to stock, the first header and U-Boot needs to be
stripped from the original firmware.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[change rssi LED labels]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Read times drop when increasing frequency to 25 MHz and 50 MHz,
but not in between or for further increase. So, use 50 MHz as the
lowest frequency with the fastest speed.
Test results (thanks to Roger):
The device reports a mx25l6405d flash chip. I tried all the maximum
values in the devices' datasheet (Table 10. AC CHARACTERISTICS). All of
them worked with and without "m25p,fast-read":
> 10 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 1m 33.00s
user 0m 0.01s
sys 1m 7.56s
> 25 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.42s
user 0m 0.02s
sys 0m 23.58s
> 25 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.45s
user 0m 0.02s
sys 0m 23.59s
> 33 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.39s
user 0m 0.00s
sys 0m 23.60s
> 33 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 34.46s
user 0m 0.01s
sys 0m 23.62s
> 50 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.81s
user 0m 0.01s
sys 0m 18.25s
> 50 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.84s
user 0m 0.00s
sys 0m 18.25s
> 66 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.01s
sys 0m 18.23s
> 66 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.02s
sys 0m 18.23s
> 86 MHz
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.84s
user 0m 0.01s
sys 0m 18.24s
> 86 MHz, fast read
root@OpenWrt:~# time cat /dev/mtd* > /dev/null
real 0m 26.80s
user 0m 0.02s
sys 0m 18.23s
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch addresses several issues for D-Link DIR-810L:
- add correct button codes
- harmonize button node names
- use generic flash@0
- remove unused pin groups from state_default
- improve sorting of properties
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The Jffs2 partition for the D-Link DIR-810L is currently off by
0x10000. Apply the correct offset based on the other partitions'
size/offset and the information about stock OS from the Wiki.
This is just based on the named information and _not_ verified
on device.
Fixes: 36e3424fa5 ("ramips: add support for dir810l and asus rp-n53")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch adds support for the Netgear R6800, aka Netgear AC1900 and
R6800-100PES.
Specification:
- SoC: MediaTek MT7621AT (880 MHz)
- Flash: 128 MiB NAND
- RAM: 256 MiB
- Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac
- LAN speed: 10/100/1000
- LAN ports: 4
- WAN speed: 10/100/1000
- WAN ports: 1
- USB 2.0
- USB 3.0
- Serial baud rate of Bootloader and factory firmware: 57600
Known issues:
- Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off.
Wifi on/off is not used.
Installation:
- apply factory image via stock web-gui.
Back to stock:
- nmrpflash can be used to recover to the stock Netgear firmware.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Global attributes enable_mirror_tx/enable_mirror_rx depend on runtime
value of another global attribute mirror_source_port which just resides
in the memory
The same functionality can be achieved by directly setting port
attribute of the same names. E.g. the following two groups of commands
achieve the same thing
swconfig dev switch0 set mirror_source_port 3
swconfig dev switch0 set enable_mirror_tx 1
swconfig dev switch0 set mirror_source_port 4
swconfig dev switch0 set enable_mirror_tx 1
swconfig dev switch0 port 3 set enable_mirror_tx 1
swconfig dev switch0 port 4 set enable_mirror_tx 1
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
All devices inherited from mt7628an_tplink_8m.dtsi and
mt7628an_tplink_8m-split-uboot.dtsi contain the same additional
includes in the DTS files.
Move them to the DTSI files instead.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, the compatible for the Ubiquiti Edgerouter X has been
defined in the DTSI file and inherited for the edgerouterx.dts,
but overwritten for the edgerouterx-sfp.dts. In contrast, the
model was stored in the DTS file in both cases.
To resolve this somewhat confusing situation, move the compatible
with the device name for edgerouterx to the DTS file as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Many DTS files contain the same includes again that are already
present in the DTSI files they are derived from.
Remove those redundant includes in the DTS files. For vocore, the
include is moved to the parent DTSI file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Looking at the current upstream driver implementation, it seems like the
TX/RX flow control is enabled only if the flow control pause option is
resolved from the device/link partner advertisements (or otherwise set).
On the other hand, our current in-tree driver force enables TX/RX
flow control by default, thus possibly leading to TX timeouts if the
other end sends pause frames (which are not properly handled?):
WARNING: CPU: 3 PID: 0 at net/sched/sch_generic.c:320 dev_watchdog+0x1ac/0x324
NETDEV WATCHDOG: eth0 (mtk_soc_eth): transmit queue 0 timed out
Disabling the flow control on PORT 5 MAC seems to fix this issues as the
pause frames are then filtered out. While at it, I'm removing the if
condition completely as suggested, since this code is run only on mt7621
SoC, so there is no need to check for the silicon revisions.
Ref: https://lists.openwrt.org/pipermail/openwrt-devel/2017-November/009882.html
Ref: https://forum.openwrt.org/t/mtk-soc-eth-watchdog-timeout-after-r11573/50000/12
Suggested-by: Felix Fietkau <nbd@nbd.name>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Stock firmware has a vendor-defined tail at the end of uImage for image
validation. This patch enables OpenWrt installation from stock firmware
without having to access the UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit adds the ability to set custom uImage magic to
Build/wr1201-factory-header and renames it to
"Build/custom-initramfs-uimage".
Custom uImage header in initramfs image is required on following
devices:
- I-O DATA WN-AX1167GR2
- I-O DATA WN-AX2033GR
- I-O DATA WN-AX2033GR2
- I-O DATA WN-DX1167R
While at it, fix typo in comment.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[shorten commit title, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
dts file does not need to be executable. 644 is enough.
Fixes: f098c612b6 ("ramips: create shared DTSI for Netgear EX2700 and WN3000RP v3")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Additonal notes
---------------
It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the various variants of common device definitions for
TP-Link devices to a common Makefile common-tp-link.mk. This
provides the opportunity to reorganize and move parameters between
individual device definitions and the common ones.
While at it, also use the common definitions for previously
independent definitions where appropriate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This converts the TP-Link TL-MR3020v3 board to use the WLAN throughput
LED trigger in order to react to all VAPs.
It also moves the WLAN trigger config of the TP-Link TL-WA801NDv5 to the
DTS and merges the now identical LAN LED configs.
Verified these changes on a TL-MR3020v3.
Signed-off-by: Jan Alexander <jan@nalx.net>
[changed commit title and extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 4716c843d6.
Netgear seems to use different partition layouts on the R6260, which
would require us to dynamically detect the position of (at least) the
factory partition.
Revert this fix to avoid breaking existing installations until a better
solution has been worked out.
Signed-off-by: David Bauer <mail@david-bauer.net>
DEVICE_PACKAGES is specified twice for the same device. Remove the
first (=older) assignment.
Fixes: 40692f0fb5 ("ramips: mt7620: select only the matching mt76 driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The EEPROM offset for the NETGEAR R6260 is incorrect, thus no valid
calibration data is used.
Fix this only for the NETGEAR R6260, as it's currently unknown whether
or not other boards are affected.
Signed-off-by: David Bauer <mail@david-bauer.net>
The GL.iNet microuter-N300 (internally referred as MT300N-v4) is a
pocket-size travel router. It is essentially identical to the VIXMINI
(internally referred as MT300N-v3) but with double the RAM and
SPI-flash.
Additionally, set the label-mac for both the VIXMINI as well as the
microuter-N300.
Hardware
--------
SoC: MediaTek MT7628NN
RAM: 128M DDR2
FLASH: 16M
LED: Power - WLAN
BTN: Reset
UART: 115200 8N1
TX and RX are labled on the board as pads next to the SoC
Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
Note: The ethernet port is by default WAN. So you need to connect to
the router via WiFi
2. Navigate to the Update tab on the left side.
3. Select "Local Update"
4. Upload the OpenWrt sysupgrade image.
Note: Make sure you select not to preserve the configuration.
Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
Wait for the LED to flash 5 times.
2. Assign yourself a static IPv4 in 192.168.1.0/24
3. Upload the OpenWrt sysupgrade image at 192.168.1.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
In ramips, all devices in mt7621, mt76x8 and rt288x subtarget have
the same value set to the SOC variable for each device individually.
This patch introduces a non-device-dependent variable DEFAULT_SOC,
which is used if no specific SOC is set for a device, and thus reduces
the number of redundant definitions drastically.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device tree property "mediatek,led_polarity" is ignored for
MT7628AN and MT7688. According to the datasheet both SoCs have
the matching register. Therefore the property should be applied
on these two devices as well.
Signed-off-by: Maximilian Pachl <m@ximilian.info>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
"#mediatek,portmap" is not a valid property name.
If mediatek,portmap equals 0x0, then the esw driver ditches it and uses
the default value, 0x3f.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt76x8 uses esw_rt3050 driver, which does not accept mediatek,portmap with
string values. Convert the strings to integers to make it work.
According to its switch setup, WRTnode 2P/2R have a WAN port at port 0,
so the correct value should be 0x3e.
tplink_8m.dtsi uses "llllw", but it does not match switch setups of any
device using the DTSI. Remove it from the DTSI and add correct value to DTS
for each device.
These devices have a WAN port at port 0. Set the value to 0x3e.
- tplink,archer-c20-v4
- tplink,archer-c50-v3
- tplink,tl-mr3420-v5
- tplink,tl-wr840n-v4
- tplink,tl-wr841n-v13
- tplink,tl-wr842n-v5
These devices have only one ethernet port. They don't need portmap setting.
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
mt7620 and mt7621 use mt7530 driver, which only accepts "llllw", "wllll",
and "lwlll" values.
According to its switch setup, Mi Router 3G v2 has a WAN port at port 4,
so the correct value should be "llllw".
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
- fix color and active mode for existing wps led
- add green wps led
- add wps button
Signed-off-by: Jan Alexander <jan@nalx.net>
[wrap line]
Signed-off-by: David Bauer <mail@david-bauer.net>
This device OOPs during the boot due to broken flash. It can be probably
fixed with `broken-flash-reset` once ramips is on 4.19 kernel.
So disable images for this device until its fixed.
Ref: FS#2695, PR#2483
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link Archer C20 v5 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch
* WAN LED in this devices is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Website and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is TP-Link MediaTek device with a split-uboot feature design like
a TP-Link Archer C50 v4. The first (factory-uboot) provides recovery via
TFTP and HTTP, jumping straight into the second (firmware-uboot) if no
recovery needs to be performed. The firmware-uboot unpacks and executed
the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5 / Archer C50v4. Stock-firmware sets a flag in the "romfile"
partition before beginning to write and removes it afterwards. If the
router boots with this flag set, bootloader will automatically start
Web-recovery and listens on 192.168.0.1. This way, the vendor-firmware
or an OpenWRT factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[adjust some node names for LEDs in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
- add "gpio" group for wan_orange led
- use tpt triggers for wifi led indication
- add wifi 5 GHz led support
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
[slight commit message adjustment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Image builds for the ramips-mt7621 target currently fail with:
> WARNING: Image file ./hiwifi_hc5962-kernel.bin is too big
Disable this board for now. It can still be built using the SDK.
Signed-off-by: David Bauer <mail@david-bauer.net>
The device label shows the address currently assigned to the OpenWrt
LAN interface.
Current setup is:
LAN *:b8 factory 0xe006 label
WAN *:b7 factory 0xe000
For vendor FW bootlog we get (manually removed parts of the address):
[ 7.520000] set LAN/WAN LWLLL
[ 7.530000] GMAC1_MAC_ADRH -- : 0x00004031
[ 7.530000] GMAC1_MAC_ADRL -- : 0x3c****b7
[ 7.530000] GDMA2_MAC_ADRH -- : 0x00004031
[ 7.540000] GDMA2_MAC_ADRL -- : 0x3c****b8
[ 7.540000] eth1: ===> VirtualIF_open
Without further information, this does not allow verification of
the currently unexpected LAN/WAN assignment (we would expect 0xe000
to be LAN).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address on the label of this device corresponds to the
2.4 GHz and ethernet MAC address.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".
This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.
Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.
The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.
An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.
Total image size with different dictionary size options:
D23 - 3973903 bytes (base)
D16 - 4113167 bytes (+3.5% - +139264 bytes)
D12 - 4317967 bytes (+8.7% - +344064 bytes)
D11 - 4383503 bytes (+10.3% - +409600 bytes)
D10 - 4461327 bytes (+12.3% - +487424 bytes)
Fixes: FS#1484
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
Images generated for the TP-Link RE200v1 cannot be updated using
sysupgrade, because a necessary call to append-metadata was missing.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link Archer C20i previously had a generic Ralink MAC address set
for both radios, as the caldata does only contain a generic MAC address.
Set the MAC address from the vendor firmware for both radios to assign
unique MAC addresses to every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
The TP-Link Archer C2 v1 previously had a generic Ralink MAC address set
for the 5GHz radio (MT7610), as the caldata does only contain a generic
MAC address.
Set the MAC address from the vendor firmware for the 5GHz radio to
assign unique MAC addresses to every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Use the WPS LED to indicate system status like it is done for the
TP-Link Archer C2 v1 and many other boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
This converts all MediaTek MT7620 boards from TP-Link to use the now
supported WiFi throughput LED trigger. This way, the LED state now
covers all VAPs regardless of their name.
Also align all single-WiFi LEDs to represent the state of the 2.4GHz
radio. This was not always the case previously, as later-added support
for the MT7610 altered the phy probing order.
Signed-off-by: David Bauer <mail@david-bauer.net>
