Commit Graph

24938 Commits

Author SHA1 Message Date
Álvaro Fernández Rojas
1b1a9d1944 bmips: vr-3032u: fix gpio keys
These GPIO keys were assigned to incorrect pins.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-29 18:23:25 +02:00
Álvaro Fernández Rojas
483cc69fef bmips: dgnd3700-v2: fix gpio keys
These GPIO keys were assigned to incorrect pins.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-29 18:23:25 +02:00
Rafał Miłecki
f8669c174e bcm53xx: fix Linksys EA9500 partitions
Use proper DT binding.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-29 09:29:16 +02:00
Rafał Miłecki
3fd0a4222b kernel: backport 5.13 mtd partitioning changes
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-29 08:46:17 +02:00
Sven Eckelmann
c20ac84803 mvebu: Fix mac addresses for GL.iNet GL-MV1000
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.

But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-03-27 16:56:50 +01:00
Shiji Yang
b88d2850c6 ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1

Fixes: e9baf8265b ("ramips: add support for Youku YK1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-27 16:54:15 +01:00
John Audia
55be1c3734 kernel: bump 5.4 to 5.4.108
All modifications made by by update_kernel.sh.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800 [only 5.4.107]
No dmesg regressions, everything functional

Run-tested by @timocapa:
 - ramips/mt7621/{Xiaomi R3G, Redmi 2100}
 - Lantiq/XWAY/Fritz!Box 7320/7330

Signed-off-by: John Audia <graysky@archlinux.us>
[squash, edit commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-27 16:39:31 +01:00
INAGAKI Hiroshi
e2331fb549 ath79: fix label_mac for NEC Aterm WG1200CR
On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label
on the case, not LAN.
This patch fixes this issue.

Fixes: 50fdc0374b ("ath79: provide label MAC address")

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-03-27 16:28:01 +01:00
Sven Eckelmann
01b911a938 mvebu: Add button support for GL.iNet GL-MV1000
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.

The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2021-03-27 16:22:11 +01:00
Hauke Mehrtens
ebfc94aee9 kernel: Move CONFIG_USERIO to generic config
The CONFIG_USERIO option is unset in multiple target configurations. On
the sunxi target it is activated. Move the kernel configuration option
to the generic kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-27 14:34:22 +01:00
Hauke Mehrtens
7d6553c72e kernel: Deactivate CONFIG_VFIO in generic kernel config
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.

Fixes: 87046e87e2 ("kernel: add missing kernel config symbol")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-27 14:34:00 +01:00
Kevin Darbyshire-Bryant
87046e87e2 kernel: add missing kernel config symbol
Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus
malta (at least) prompted for this new symbol.

Set it to 'false' in the default config.  rockchip & X86 enable it in
target specific configs.

Thanks to Tony Ambardar for falling over this one

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-27 09:09:57 +00:00
Stan Grishin
64eaf633ff x86/base-files: add support for Sophos SG/XG-105
This adds detection of the Sophos SG-105 and Sophos XG-105 models
and assignment of ethernet ports these models have to LAN/WAN.

Signed-off-by: Stan Grishin <stangri@melmac.net>
2021-03-26 09:15:38 -10:00
Rui Salvaterra
27344b3784 kernel: bump 5.10 to 5.10.26
Automatically refreshed:
ath79/patches-5.10/471-mtd-cfi_cmdset_0002-AMD-chip-0x2201-write-words.patch
bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch
generic/hack-5.10/204-module_strip.patch

Run-tested:
ath79 (TL-WDR3600)
x86_64 (APU2 - ldir)

Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-26 08:19:11 +00:00
Rafał Miłecki
6dd727ac24 kernel: create bootfs partition when parsing on BCM4908
It's helpful for accessing booting data (DTS, kernel, etc.). It has to
be used carefully as CFE's JFFS2 support is quite dumb. It doesn't
recognize deleted files and has problems handling 0 inode.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-24 18:22:37 +01:00
Daniel Golle
6f5cd3bdcf
mediatek: generate complete sdcard image for BPi-R64
Populate the recovery and production partitions of the generated sdcard
image for the Bananapi BPi-R64.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-24 15:27:54 +00:00
Álvaro Fernández Rojas
5053593e66 bmips: reorganize patches
Reorder kernel patches after recent backports.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-24 14:49:46 +01:00
Álvaro Fernández Rojas
4165e565d2 bmips: switch to upstream ehci overcurrent flag
After backporting upstream ehci overcurrent patches we need to use spurious-oc
instead of ignore-oc.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-24 14:19:12 +01:00
Álvaro Fernández Rojas
bd47189602 kernel: backport ehci overcurrent patches
These patches have been accepted for v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-24 14:05:38 +01:00
Kevin Darbyshire-Bryant
22d2c972c4 kernel: drop apu2 reboot patch
This patch really annoys me, either it needs to go upstream or be
dropped, so it's going to be dropped here.

Checking drivers/platform/x86/pcengines-apuv2.c it also appears to be
incomplete since it mentions different dmi board names depending on bios
version.

/* APU2 w/ legacy BIOS < 4.0.8 */ is 'APU2'
/* APU2 w/ legacy BIOS >= 4.0.8 */ is 'apu2'
/* APU2 w/ mainline BIOS */ is 'PC Engines apu2'

So the patch, if applicable at all, only 'works' for legacy BIOS >=
4.0.8

My APU2 on mainline BIOS reboots fine without this patch.  So let's see
if anyone screams and when they do question why legacy bios.  If patch
DOES need to be re-introduced then it needs to go upstream first.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-24 11:51:29 +00:00
Kevin Darbyshire-Bryant
d07ac3e376 kernel: bump 5.10 to 5.10.25
Straightforward refresh of patches using update_kernel.

Removed (reverse-applicable):
bmips/patches-5.10/010-v5.11-net-dsa-implement-a-central-TX-reallocation-procedur.patch

Run tested: x86_64 (apu2)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-24 11:39:05 +00:00
Kevin Darbyshire-Bryant
eb964298b3 kernel: bump 5.10 to 5.10.24
Straightforward refresh of patches using update_kernel.

Run tested: x86_64 (apu2)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-24 11:36:31 +00:00
Álvaro Fernández Rojas
07c49462ad bmips: add wifi packages for supported devices
Netgear DGND3700v2 / Comtrend VR-3032u internal wireless not supported.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:23:47 +01:00
Álvaro Fernández Rojas
2024547e1f bmips: add ATH9K PCI fixups
Add support for registering ATH9K PCI fixups needed to bring up wifi on some
devices.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:16:37 +01:00
Álvaro Fernández Rojas
793047bb0f bmips: add B43 SPROM PCI fixups
Add support for registering fallback BCMA/SSB B43 SPROMs.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:14:38 +01:00
Álvaro Fernández Rojas
7f04d67517 bmips: add experimental PCI/PCIe support
These PCI drivers are a bit hacky and definitely not suitable for upstreaming,
but hopefully we can use them as a base for developing proper upstream PCI
drivers.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:12:22 +01:00
Adrian Schmutzler
851dadc257 realtek: add ZYXEL_VERS to DEVICE_VARS
Otherwise, the last defined value will be set for all devices.

Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-22 20:58:16 +01:00
Shiji Yang
bf7ddb18f1 ramips: speed up spi frequency for Youku YK-L1
Youku YK-L1 has a huge storage space up to 32 MB. It is better to
use a higher spi clock to read or write serial nor flash chips.
Youku YK-L1 has Winbond w25q256fvfg on board that can support
104 MHz spi clock so 48 MHz is safe enough.
The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz
defined in dts file will set only 48 MHz in spi bus.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-22 20:54:34 +01:00
Mauri Sandberg
e87527b57d ath79: copy cfi patch from 5.4 over to 5.10
Add the same patch to 5.10 too. The patch is in process of being
upstreamed.

Fixes: 8cc0fa8fac ("ath79: cfi: cmdset_0002: amd chip
0x2201 - write words")

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-22 20:53:22 +01:00
Mauri Sandberg
bc356de285 ath79: Add support for Buffalo WZR-HP-G300NH
This device is a wireless router working on 2.4GHz band based on
Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103
wireless chip and Realtek RTL8366RB/S switches. Due to two different
switches being used also two different devices are provided.

  Specification:
  - 400 MHz CPU
  - 64 MB of RAM
  - 32 MB of FLASH (NOR)
  - 3x3:2 2.4 GHz 802.11bgn
  - 5x 10/100/1000 Mbps Ethernet
  - 4x LED, 3x button, On/Off slider, Auto/On/Off slider
  - 1x USB 2.0
  - bare UART header place on PCB

  Flash instruction:
  - NOTE: Pay attention to the switch variant and choose the image to
    flash accordingly. (dmesg / kernel logs can tell it)
  - Methods for flashing
    - Apply factory image in OEM firmware web-gui.
    - Sysupgrade on top of existing OpenWRT image
    - U-Boot TFPT recovery for both stock or OpenWRT images:
      The device U-boot contains a TFTP server that by default has
      an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot
      there is a time window, during which the device allows an image to
      be uploaded from a client with address 192.168.11.2. The image will
      be written on flash automatically.

      1) Have a computer with static IP address 192.168.11.2 and the
         router device switched off.
      2) Connect the LAN port next to the WAN port in the device and the
         computer using a network switch.
      3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A
         arp -s 192.168.11.1 02:AA:BB:CC:DD:1A
      4) Initiate an upload using TFTP image variant
         curl -T <imagename> tftp://192.168.11.1
      5) Switch on the device. The image will be uploaded subsequently.
         You can keep an eye on the diag light on the device, it should
         keep on blinking for a while indicating the writing of the image.

  General notes:
  - In the stock firmware the MAC address is the same among all
    interfaces so it is left here that way too.

  Recovery:
  - TFTP method
  - U-boot serial console

  Differences to ar71xx platform
  - This device is split in two different targets now due to hardware
    being a bit different under the hood. Dynamic solution within the same
    image is left for later time.
  - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device
    cover, were the wrong way around and were renamed qos_on -> movie_off,
    qos_off -> movie_on. Associated key codes remained the same they were.

  The device tree source code is mostly based on musashino's work

Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
2021-03-22 09:23:10 +01:00
Mauri Sandberg
8cc0fa8fac ath79: cfi: cmdset_0002: amd chip 0x2201 - write words
Generally, in upstream CFI flash memory driver uses buffers for write
operations. That does not work with AMD chip with id 0x2201 and we must
resort to writing word sized chunks only. That is, to not apply general
buffer write functionality for this given chip.

Without the patch kernel logs will be flooded with entries like below:

MTD do_erase_oneblock(): ERASE 0x01fa0000
MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985)
MTD do_erase_oneblock(): ERASE 0x01f80000
MTD do_write_buffer(): WRITE 0x01f80000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f8000a.
jffs2: Write clean marker to block at 0x01a60000 failed: -5
MTD do_erase_oneblock(): ERASE 0x01f60000
MTD do_write_buffer(): WRITE 0x01f60000(0x00001985)
MTD do_write_buffer_wait(): software timeout, address:0x01f6000a.
jffs2: Write clean marker to block at 0x01a40000 failed: -5

References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to usptream fix submission]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-03-22 09:23:10 +01:00
Rafał Miłecki
a49fd9db0a bcm4908: backport the latest bcm_sf2 commits
1. CFP support for BCM4908
2. Upstream RGMII regs fix

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-22 08:19:36 +01:00
Rafał Miłecki
13d9904acd bcm4908: backport DTS patch with Ethernet TX IRQ
It allows bcm4908_enet Linux driver to work more efficiently.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-22 07:45:34 +01:00
Rafał Miłecki
2b4986b942 bcm4908: add MTD support for repartitioning
It's required for sysupgrade which requires:
1. Flashing new firmware
2. Finding updated bootfs partition
3. Updating bootfs content

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-22 07:44:10 +01:00
Walter Sonius
46c0634b50 ath79: fix lan port display order for sitecom wlr-7100
Physical port order watched from the back of the device is:
4 / 3 / 2 / 1 / WAN which also matches corresponding leds.
This patch corrects LuCI switch webpage LAN port order.

Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[improve commit title, fix sorting in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
John Audia
2c81b16964 kernel: bump 5.4 to 5.4.106
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Manually rebased:
  bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
  layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
INAGAKI Hiroshi
b3ca1f30ef ramips: add support for ELECOM WRC-1750GST2
ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 256 MiB (NT5CC128M16JR-EK)
- Flash		: SPI-NOR 32 MiB (MX25L25645GMI-08G)
- WLAN		: 2.4/5 GHz 3T3R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX, from ethernet port side
  - 57600n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-1750GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC addresses:

LAN	: 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex))
WAN	: 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex))
2.4GHz	: 04:AB:18:xx:xx:25 (Factory, 0x4    (hex))
5GHz	: 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-03-21 22:45:20 +01:00
Shiji Yang
df6154848a ramips: create shared DTSI for MT7620 Phicomm K2x series devices
Improve compatibility of the device tree include file. Now a new .dtsi
file will support both PSG1218A, PSG1218B and K2G.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title, rebase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Shiji Yang
c36e47c5da ramips: increase SPI frequency for Phicomm series devices
From many teardown image in the internet, I find Phicomm K1/k2 series use
Winbond W25Q64/W25Q128 or GigaDevice GD25Q64/GD25Q128 Flash chips. both of
them support 100+ MHz clock spi operate and fast-read instruction. PSG1218
with W25x or GD25x has been tested and it can run well in OpenWrt v19.07.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Shiji Yang
d160b2c824 ramips: increase SPI frequency for HIWIFI HC5x61 devices
HIWIFI HC5x61 devices support high speed spi clock up to 100+ MHz.
So set spi frequency to 80 MHz here (Due to frequency division the
real clock is 48 MHz).
I have tested HC5661 and it can run well in OpenWrt v19.07.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[adjust commit title and wrap message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-21 22:45:20 +01:00
Daniel Golle
310b7f76e8
mediatek: linksys-e8450: remove left-overs from dtsi
There is an ASMedia ASM1480 PCIe switch found on mt7622-rfb1 and the
BPi-R64, allowing the user to switch between SATA and PCIe1 which share
the same pins on the SoC.
This chip is not present on the Linksys E8450, it doesn't have SATA.
Remove definitions for GPIO90 from DTSI to prevent it from being
copy&pasted or otherwise causing confusion.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-21 13:38:42 +00:00
Álvaro Fernández Rojas
f93b544f01 bcm27xx: bcm2711: correctly disable HW_RANDOM_BCM2835
It was removed in bac74aff5e, but it should have been disabled.
More info: https://forum.openwrt.org/t/make-image-stops-at-random-number-generator-bcm27xx/91429/7

Fixes: bac74aff5e ("bcm27xx: bcm2711: disable HW_RANDOM_BCM2835")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-21 12:39:47 +01:00
Hauke Mehrtens
0c0cb97da7 kernel: Add missing kernel config options
These two options are missing when building the x86 target.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 18:48:32 +01:00
Hauke Mehrtens
0b5a67aa03 kernel: Reorder kernel configuration options
Reorder the options and remove double entries.
This was generated by running this:
$ ./scripts/kconfig.pl '+' target/linux/generic/config-5.10 /dev/null > target/linux/generic/config-5.10.new
$ mv target/linux/generic/config-5.10.new target/linux/generic/config-5.10
$ ./scripts/kconfig.pl '+' target/linux/generic/config-5.4 /dev/null > target/linux/generic/config-5.4.new
$ mv target/linux/generic/config-5.4.new target/linux/generic/config-5.4

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 18:38:35 +01:00
Hauke Mehrtens
047b7621bb archs38: Add CONFIG_HZ=100
This kernel config option was missing and resulted in a question when
building.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 18:00:22 +01:00
Rosen Penev
a50441b6e9 kernel: add exfat again
With kernel 5.10, exfat is out of staging and in tree.

Added small hack to make it work with kernel 5.4 as well.

Added removed config options for 5.4 to generic config.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-19 16:08:12 +01:00
Tad Davanzo
b4f76d9f0d mvebu: enable WRT1900AC v1 and WRT32X for buildbots
Kernel size limits have been dealt with.
Effective revert of a1eb2c46 and ac9730c4.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tad Davanzo
15309f5133 mvebu: venom resize kernel to 6MB
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0x900000, size 0x600000
	6291456 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "priKernSize";
	priKernSize=0x0600000

Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.

Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tad Davanzo
10415d5e70 mvebu: mamba resize kernel to 4MB
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.

mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
	NAND read: device 0 offset 0xa00000, size 0x400000
	4194304 bytes read: OK
and from uboot environment variables:
	$ fw_printenv | grep "pri_kern_size";
	pri_kern_size=0x400000

Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.

Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.

Signed-off-by: Tad Davanzo <tad@spotco.us>
2021-03-19 15:30:01 +01:00
Tony Ambardar
9662da770e kernel: add missing config symbols, fix typos
Update 5.10 generic config to add missing options prompting during builds,
when setting CONFIG_ALL_KMODS. Refresh the x86 subtargets to drop symbols
added to the generic config.

Also fix a typo in 5.4/5.10 generic configs: "CONFIG_CONFIG_KVM_AMD_SEV".

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-19 14:02:47 +00:00
Daniel Golle
d0d63162b6
ipq806x: work-around vendor 'rootfs_data' GPT partition
ZyXEL NBG6817 comes with an eMMC which contains a GPT partition named
'rootfs_data'. This currently confuses fstools and makes it pick that
(not suitable) partition.
Use the newly introduced fstools_ignore_partname=1 kernel cmdline
parameter to have fstools ignore that partition.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-19 13:36:02 +00:00
Álvaro Fernández Rojas
df26c29629 bmips: backport b53 mmap device tree support
This patch has been accepted upstream for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-19 11:00:19 +01:00
Álvaro Fernández Rojas
a139ab1b82 bmips: backport b53 legacy tags support
These patches have been accepted upstream for linux 5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-19 11:00:19 +01:00
Álvaro Fernández Rojas
d6c5698a71 bmips: backport upstream dsa b53 is63xx patch
This patch has been accepted for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-19 11:00:19 +01:00
Ilya Lipnitskiy
f65b0afadb ramips: move spi-nor-add-gd25q512 patch to generic
A SPI NOR flash should not be target-specific, so move it to generic in
case another platform needs to use it.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-19 01:25:26 +01:00
Lech Perczak
410fb05b44 rampis: use lzma-loader for ZTE MF283+
Without that, after merging support to master, the device fails to boot
due to LZMA decompression error:

3: System Boot system code via Flash.
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
.   Image Name:   MIPS OpenWrt Linux-5.4.99
   Created:      2021-02-25  23:35:00 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1786664 Bytes =  1.7 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:80040 len:1b4328
............................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

Use lzma-loader to fix it.

Fixes: 59d065c9f8 ("ramips: add support for ZTE MF283+")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2021-03-19 01:25:26 +01:00
Shiji Yang
a94a20373b ramips: improve GPIO pin control for HC5x61
HC5661 does not have USB port, remove usb power control pin.
HC5x61 do not have LAN LEDs, remove ethernet LED control pin.
Only HC5861 has PA in 2.4G channel.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-19 01:25:26 +01:00
Aleksander Jan Bajkowski
12e942b1fd kernel: move some disabled symbols to generic
Move some disabled symbols found in armvirt target to generic.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-03-19 00:59:22 +01:00
Aleksander Jan Bajkowski
c027dbac5a lantiq: set maximum kernel size for ARV7519RW22
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.

Set maximum kernel size and disable image building for this board.

Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-03-18 16:17:43 +01:00
David Bauer
42d943f40a mediatek: fix broken UniFi 6 LR image
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-03-18 00:56:33 +01:00
David Bauer
ac5675ec8f ramips: fix broken UniFi 6 Lite image
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-03-18 00:54:25 +01:00
Hauke Mehrtens
0e3f6fbe10 mediatek: Fix writing U-Boot env on Buffalo WSR-2533DHP2
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-17 22:39:59 +00:00
Daniel Golle
b40f707f71 mediatek: bpi-r64: use dt-overlay to select SATA or PCIE1
The Bananapi BPi-R64 got a SATA interface which cannot be used at the
same time as the second mPCIe slot. The decission is made by hogging
GPIO 90.
Embed two addtional DT overlay blobs into the image to allow bootloader
selection of either SATA or PCIE1 feature.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-17 19:12:19 +00:00
Daniel Golle
6890f6fe13 include/image*: add support for device-tree overlays
Add new target feature 'dt-overlay' which makes DTC keep the symbol
names in the generated dtb.
Make sure additional DT overlay sources specified by the new device
variable DEVICE_DTS_OVERLAY get compiled together with the main DTS
(currently overlays got to be in the same folder). Let Build/fit pass
the generated DT overlay blobs to mkits.sh.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-17 17:45:34 +00:00
Daniel Golle
53a7d5d614 ath79: fix RS-485 on Teltonika RUT-955
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).

Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-17 17:41:24 +00:00
Tony Ambardar
6eca2e40e7 malta: prune subtarget configs
Drop autogenerated kernel config options. These aren't needed to build and
can obscure options relevant to the subtarget.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-17 15:35:33 +01:00
Tony Ambardar
fd1c285040 malta: update kernel 5.10 configs
Update generic config to add missing options that prompt during builds. Run
"make kernel_oldconfig" to refresh malta target config.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-17 15:35:33 +01:00
Tony Ambardar
3e2f42a802 malta: support kernel 5.10
Add linux 5.10 as testing kernel and copy generic config from 5.4.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-17 15:35:33 +01:00
Bjørn Mork
963b2ae702 realtek: enable SerDes NWAY and SGMII negotiation
This allows copper SFPs to negotiate speeds lower than 1gig.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
07bf5aaa4c realtek: enabled Marvell and Realtek PHYs
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.

1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
2a912fb63a realtek: enable HWMON for SFP sensors
This adds SFP sensors as a hwmon device, allowing readout of
temperatures, DOM and other sensor readings available from the
SFP.  Example from a ZyXEL GS1900-10HP with a DOM capable
1000Base-SX SFP:

root@gs1900-10hp:~# grep . /sys/class/hwmon/hwmon0/*
/sys/class/hwmon/hwmon0/curr1_crit:90
/sys/class/hwmon/hwmon0/curr1_crit_alarm:0
/sys/class/hwmon/hwmon0/curr1_input:4
/sys/class/hwmon/hwmon0/curr1_label:bias
/sys/class/hwmon/hwmon0/curr1_lcrit:0
/sys/class/hwmon/hwmon0/curr1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/curr1_max:85
/sys/class/hwmon/hwmon0/curr1_max_alarm:0
/sys/class/hwmon/hwmon0/curr1_min:0
/sys/class/hwmon/hwmon0/curr1_min_alarm:0
/sys/class/hwmon/hwmon0/in0_crit:3795
/sys/class/hwmon/hwmon0/in0_crit_alarm:0
/sys/class/hwmon/hwmon0/in0_input:3317
/sys/class/hwmon/hwmon0/in0_label:VCC
/sys/class/hwmon/hwmon0/in0_lcrit:2805
/sys/class/hwmon/hwmon0/in0_lcrit_alarm:0
/sys/class/hwmon/hwmon0/in0_max:3465
/sys/class/hwmon/hwmon0/in0_max_alarm:0
/sys/class/hwmon/hwmon0/in0_min:3135
/sys/class/hwmon/hwmon0/in0_min_alarm:0
/sys/class/hwmon/hwmon0/name:sfp_p10
/sys/class/hwmon/hwmon0/power1_crit:708
/sys/class/hwmon/hwmon0/power1_crit_alarm:0
/sys/class/hwmon/hwmon0/power1_input:259
/sys/class/hwmon/hwmon0/power1_label:TX_power
/sys/class/hwmon/hwmon0/power1_lcrit:89
/sys/class/hwmon/hwmon0/power1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/power1_max:501
/sys/class/hwmon/hwmon0/power1_max_alarm:0
/sys/class/hwmon/hwmon0/power1_min:126
/sys/class/hwmon/hwmon0/power1_min_alarm:0
/sys/class/hwmon/hwmon0/power2_crit:1259
/sys/class/hwmon/hwmon0/power2_crit_alarm:0
/sys/class/hwmon/hwmon0/power2_input:404
/sys/class/hwmon/hwmon0/power2_label:RX_power
/sys/class/hwmon/hwmon0/power2_lcrit:6
/sys/class/hwmon/hwmon0/power2_lcrit_alarm:0
/sys/class/hwmon/hwmon0/power2_max:794
/sys/class/hwmon/hwmon0/power2_max_alarm:0
/sys/class/hwmon/hwmon0/power2_min:10
/sys/class/hwmon/hwmon0/power2_min_alarm:0
/sys/class/hwmon/hwmon0/temp1_crit:100000
/sys/class/hwmon/hwmon0/temp1_crit_alarm:0
/sys/class/hwmon/hwmon0/temp1_input:22547
/sys/class/hwmon/hwmon0/temp1_label:temperature
/sys/class/hwmon/hwmon0/temp1_lcrit:-50000
/sys/class/hwmon/hwmon0/temp1_lcrit_alarm:0
/sys/class/hwmon/hwmon0/temp1_max:85000
/sys/class/hwmon/hwmon0/temp1_max_alarm:0
/sys/class/hwmon/hwmon0/temp1_min:-40000
/sys/class/hwmon/hwmon0/temp1_min_alarm:0
/sys/class/hwmon/hwmon0/uevent:OF_NAME=sfp-p10
/sys/class/hwmon/hwmon0/uevent:OF_FULLNAME=/sfp-p10
/sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_0=sff,sfp
/sys/class/hwmon/hwmon0/uevent:OF_COMPATIBLE_N=1

Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
e8d391bd46 realtek: re-enable sfp driver for ZyXEL GS1900-10HP
There is no need to define a static link or a phy for the sfp
ports.  Using phy-mode and managed properties to  describe the
link to the sfp phy.

We have to keep the now unconnected virtual "phys" because the
switch  driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
785d830e88 realtek: need to handle PHY_INTERFACE_MODE_NA for sfps
From the validate docs in include/linux/phylink.h:

 When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
 MAC driver to return all supported link modes.

Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Bjørn Mork
b8e473d18c realtek: fix link-state interrupt
This bug was the root cause for the failing sfp driver.

Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-03-17 10:01:21 +01:00
Rafał Miłecki
e1b4fd52a8 bcm4908: backport recent bcm_sf2 changes
One 5.12 link fix and 5.13 crossbar support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-17 08:10:54 +01:00
Rafał Miłecki
7091e31230 bcm4908: backport recent bcm4908_enet changes
This includes 5.12 fix and 5.13 improvements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-16 23:57:52 +01:00
Paul Spooren
0f7cd97f81 build,ib: add STRIP_ABI option for manifest
The ImageBuilder `make manifest` prints all installed packages. This
function can be used to create a list of package and corresponding
package versions before attempting image creation.

When called with `--strip-abi` OPKG can automatically strip attached
ABIVersions from package names. Make this function accessible for the
ImageBuilder by adding a `STRIP_ABI` variable.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2021-03-16 11:00:08 -10:00
Álvaro Fernández Rojas
34f898ec29 bmips: backport bcm6368-mdio-mux support
This patch has been accepted for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:06:00 +01:00
Álvaro Fernández Rojas
7ec9d95567 bmips: enable CONFIG_B53_MDIO_DRIVER
Some devices have external switches connected by MDIO.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:00:51 +01:00
Álvaro Fernández Rojas
b434c524b1 bmips: backport b53 spi device tree patch
This patch has been accepted for linux v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:00:51 +01:00
Álvaro Fernández Rojas
be16951494 bmips: dgnd3700-v2: fix ethernet
This is a temporary workaround to get the ethernet working, since external
switch is connected by MDIO and it needs additional work.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-16 20:00:51 +01:00
Ilya Lipnitskiy
680f91d0e5 kernel: backports: mt7530: fix TRGMII mode after reset
Backport upstream patch that fixes TRGMII mode now that mt7530 is
actually resetting the switch on ramips devices.

Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both.

Fixes: 69551a2442 ("ramips: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-16 19:27:55 +08:00
Tony Ambardar
662ceebc4c x86/legacy: fix subtarget CPU for kernel 5.10
The 5.10 target config defined a baseline i686 CPU aligned to the 32-bit
generic subtarget. However, the legacy subtarget arch wasn't set to the
older 586MMX, defaulting instead to the i686.

Explicitly set the subtarget arch and refresh the subtarget config, as done
already with the old geode subtarget.

Fixes: 8391781389 ("x86: support kernel 5.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-15 19:12:03 -07:00
Rafał Miłecki
d7c8ca4d0b bcm4908: backport first PHY 5.13 patches
1. Upstream accepted version of Kconfig change
2. Documentation binding fix

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-15 20:30:21 +01:00
Daniel Golle
c17b1dca60
mediatek: mt7622: drop duplicate DEVICE_PACKAGES
kmod-mt7615e kmod-mt7615-firmware and uboot-envtools are already part
of the target's default package set. No need to add them again for
buffalo_wsr-2533dhp2.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-15 16:40:31 +00:00
INAGAKI Hiroshi
74f15628dd mediatek: add support for Buffalo WSR-2533DHP2
This adds support for the Buffalo WSR-2533DHP2.

The device uses the Broadcom TRX image format with a special magic. To
be able to boot the images or load them they have to be wrapped with
different headers depending how it is loaded.

There are multiple ways to install OpenWrt on this device.
Boot ramdisk from U-Boot
----------------------------
This will load the image and not write it into the flash.

1. Stop boot menu with "space" key
2. Select "System Load Linux to SDRAM via TFTP."
3. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin
4. The system boots the image

Write to flash from U-Boot
-----------------------------
This will load the image over tftp and directly write it into the flash.

1. Stop boot menu with "space" key
2. Select "System Load Linux Kernel then write to Flash via TFTP."
3. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin
4. The system writes this image into the flash and boots into it.

Write to flash from Web UI
-----------------------------
This will load the image over over the Web UI and write it into the flash

1. Open the Web UI
2. Go to "管理" -> "ファームウェア更新"
3. Select "ローカルファイル指定" and click "更新実行"
4. Load this image:
   openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin
5. The system writes this image into the flash and boots into it.

Specifications
-------------------
* SoC:       MT7622 (4x4 2.4 GHz Wifi)
* Wifi:      MT7615 (4x4 5 GHz Wifi)
* Flash:     Winbond W29N01HZ 128MB SLC NAND
* RAM        256MB
* Ethernet:  Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s)

Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-15 17:02:17 +01:00
Hauke Mehrtens
58c5e25664 mediatek: support non standard trx magic values
Buffalo uses the TRX format with a different magic, add support for
this.

It is planned to send these patches upstream.

Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-15 16:57:34 +01:00
Hauke Mehrtens
cb740fbe25 mediatek: fix mtk parallel nand driver
This fixes some bugs in the mtk parallel nand driver introduced in 5.10.

This patch was send upstream.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-15 16:57:34 +01:00
Felix Fietkau
4a79c32fee kernel: replace threaded NAPI implementation in 5.10 with upstream backport
This uses a kthread per NAPI instance instead of the workqueue approach

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-03-15 14:05:43 +01:00
Daniel Golle
34adb6db1d
mediatek: mt7622: clean up image build
* clean up whitespace to make GPT partitioning more readable
 * don't select packages already part of the target default selection
 * don't select U-Boot variants (breaks ImageBuilder)
 * don't select AHCI on boards without SATA
 * don't select kmod-usb2 and kmod-ohci, USB 1.x and USB 2.0 devices
   work fine with the in-SoC XHCI host having just kmod-usb3 installed.
 * select kmod-btmtkuart for devices with Bluetooth support
 * sort DEVICE_PACKAGES

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-14 22:00:10 +00:00
Rafał Miłecki
05dbfe616d bcm4908: use accepted 5.13 DTS patches
Some patches were slightly cleaned up. One things worth mentioning is
that adding:
phy-mode = "rgmii"
broke SF2 driver. It made it access random register breaking switch
setup.

That's why this commit also adds a quick sf2 fix.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-14 22:54:45 +01:00
Rafał Miłecki
98d456a14e bcm53xx: backport first 5.13 DTS changes
This adds NVMEM bindings that are needed for proper booting on Linksys
devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-14 19:11:05 +01:00
Tony Ambardar
8391781389 x86: support kernel 5.10
Add linux 5.10 as testing kernel, copy generic/subtarget configs and target
patches from 5.4.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>

x86: update target patches for kernel 5.10

Refresh all patches while also dropping:
    800-hwmon-w83627ehf-dont-claim-nct677x.patch

which is now upstreamed as:
    3207408ab4cb ("hwmon: (w83627ehf) remove nct6775 and nct6776 support")

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>

x86: refresh 5.10 target config

Refresh config using "make kernel_oldconfig".

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>

x86: refresh and test all subtarget configs

Refresh configs using "make kernel_oldconfig CONFIG_TARGET=subtarget".

Build and run-tested using QEMU: x86/64, x86/legacy, x86/generic.
Build-tested only: x86/geode.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[squashed commits]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2021-03-14 17:52:49 +00:00
Tony Ambardar
95a3741d17 kernel: support new mdio_devres.ko module in 5.10
Add kmod-mdio-devres package and kernel config symbol, and update related
kmod-r8169 and kmod-ixgbe package dependencies.

Build tested module dependencies on x86/64 with CONFIG_ALL_KMODS=y.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-14 17:52:49 +00:00
Tony Ambardar
736edf9dea kernel: add missing config symbols for 5.10
Update generic config to add missing options that prompt during builds.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-03-14 17:52:49 +00:00
Álvaro Fernández Rojas
ecc058b6a0 bmips: minor ethernet driver cleanups and fixes
Add some minor ethernet driver cleanups and fixes to improve code quality.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-14 16:21:27 +01:00
Álvaro Fernández Rojas
4a81b00a05 bmips: reorganize patches
Rename and reorganize backported patches.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-14 16:21:27 +01:00
Hauke Mehrtens
e6ba970b6e realtek: Add ZyXEL GS1900-8
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.

Specifications
--------------
* Device:    ZyXEL GS1900-8 v1.2
* SoC:       Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash:     Macronix MX25L12835F 16 MiB
* RAM:       Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet:  8x 10/100/1000 Mbit
* LEDs:      1 PWR LED (green, not configurable)
             1 SYS LED (green, configurable)
             8 ethernet port status LEDs (green, SoC controlled)
* Buttons:   1 on-off glide switch at the back (not configurable)
             1 reset button at the right side, behind the air-vent
               (not configurable)
             1 reset button on front panel (configurable)
* Power      12V 1A barrel connector
* UART:      1 serial header (JP2) with populated standard pin connector on
             the left side of the PCB, towards the back. Pins are labelled:
             + VCC (3.3V)
             + TX (really RX)
             + RX (really TX)
             + GND
             the labelling is done from the usb2serial connector's point of
             view, so RX/ TX are mixed up.

Serial connection parameters for both devices: 115200 8N1.

Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.

* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
  image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
  space bar, and enable the network:
  > rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
  OEM firmware on the backup partition for the time being. OpenWrt can
  only boot off the first partition anyway (hardcoded in the DTS). To
  make sure we are manipulating the first partition, issue the following
  commands:
  > setsys bootpartition 0
  > savesys
* Download the image onto the device and boot from it:
  > tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
  > bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
  > sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-14 15:07:30 +01:00
Hauke Mehrtens
c6c8d597e1 realtek: Add generic zyxel_gs1900 image definition
Add a new common device definition for the Zyxel GS1900 line of
switches.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-03-14 15:03:00 +01:00
Álvaro Fernández Rojas
28dcb74de3 bmips: add experimental ethernet support
This adds experimental ethernet support for BCM6318, BCM6328, BCM6362, BCM6368
and BCM63268.
BCM6358 needs a different driver, so there's no support for now.

Working devices:
- Comtrend AR-5315u
- Comtrend AR-5387un
- Comtrend VR-3025u
- Comtrend VR-3032u

Not working devices:
- Netgear DGND3700 v2 (no idea on how the external switch is connected)
- Huawei HG556a ver B (BCM6358 needs a separate driveer)

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-14 12:05:17 +01:00
Daniel González Cabanelas
b0235c0d8d mvebu: LS421DE: make cosmetics changes in dts file
Make some cosmetic changes in the Buffalo LinkStation LS421DE NAS:
  - Delete pointless #xxx-cells
  - bootargs: replace earlyprintk with earlycon and remove unneeded args.
  - Separate pinmux nodes with empty lines.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-03-13 20:15:29 +00:00
Kabuli Chana
1cd098784e kernel: bump 5.10 to 5.10.23
update kernel to 5.10.23, rebase patches, deleted upstreamed patch:

target/linux/generic/backport-5.10/830-v5.12-0001-net-usb-qmi_wwan-support-ZTE-P685M-modem.patch

compile / test - mvebu / mamba, rango

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-13 17:06:42 +01:00
John Audia
e7fa97b326 kernel: bump 5.4 to 5.4.105
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Removed upstreamed generic-backports:
  830-v5.12-0001-net-usb-qmi_wwan-support-ZTE-P685M-modem.patch
  831-v5.9-usbip-tools-fix-build-error-for-multiple-definition.patch
  755-v5.8-net-dsa-add-GRO-support-via-gro_cells.patch

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
[squash patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-13 17:06:35 +01:00
Daniel Golle
1a7ef2c3cf
mediatek: image: don't use 'M' unit as dd may not support that
dd on Mac OS X apparently fails when using 'M' unit for bs.
dd: bs: illegal numeric value
Use 'k' unit instead for 'pad-to' to fix that.

Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-13 15:36:57 +00:00
Rafał Miłecki
9530b9bb78 bcm47xx: make WGT634U NVRAM patch apply again
Fixes: 1c48eee5b2 ("kernel: backport Broadcom NVRAM driver cleanups")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-12 21:09:11 +01:00
Felix Fietkau
3d1ea0d77f kernel: add compatibility with upstream threaded NAPI patch
Enable threading if dev->threaded is set. This will be used to bring mt76 back
in sync with upstream

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-03-12 20:23:52 +01:00
Felix Fietkau
0d5bf53197 kernel: update 5.10 flow offload patches
Includes PPPoE support and VLAN related fixes

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-03-12 20:23:52 +01:00
Rafał Miłecki
e90e75b12c kernel: add pending mtd patches adding NVMEM support
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-12 18:49:46 +01:00
Rafał Miłecki
deceb03993 kernel: move mtd ofpart accepted patch
Move upstream patch to the backport directory.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-12 18:32:01 +01:00
Rafał Miłecki
b2b75e1939 kernel: add two more missed 5.10 backports
Those were added to 5.4 but missed while introducing 5.10 kernel.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-12 18:31:58 +01:00
Rafał Miłecki
baf04eed02 bcm53xx: initialize NVRAM from NVMEM driver
NVRAM access may be needed early in boot process. Reading it using mtd
happens quite late in the init process. Add NVRAM initialization to the
NVMEM driver which comes up early and depends on IO mapping only.

This is required by Linksys devices which use NVRAM content for proper
partitioning (detecting current firmware partition).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-12 18:22:18 +01:00
Rafał Miłecki
1c48eee5b2 kernel: backport Broadcom NVRAM driver cleanups
Refactoring of bcm47xx_nvram driver. It's used by bcm47xx and bcm53xx.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-12 18:08:41 +01:00
Álvaro Fernández Rojas
36b404a226 bmips: switch to upstream bcm2835-rng reset patch
This patch has been accepted upstream.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-12 14:29:51 +01:00
Bjørn Mork
ba220ad2fd realtek: drop ethtool log noise
Demote a number of debugging printk's to pr_debug to avoid log
nosie.  Several of these functions are called as a result of
userspace activity.  This can cause a lot of log noise when
userspace does periodic polling.

Most of this could probably be removed completely, but let's
keep it for now since these drivers are still in development.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2021-03-12 00:46:00 +02:00
Rafał Miłecki
01b1b37528 bcm53xx: backport NVMEM NVRAM driver
It supports NVRAM access described using DT binding. Right now NVRAM
data is exposed using /sys/bus/nvmem/ only.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-10 23:23:47 +01:00
Rafał Miłecki
af8a49a4be Revert "bcm53xx: add support for reading NVRAM based on DT mapping"
This reverts commit b0376462c1. Those
changes were rejected and were replaced with an NVMEM driver.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-10 22:29:15 +01:00
Álvaro Fernández Rojas
76d5677c75 bmips: automatically detect RAM size
Introduce new patch for automatically detecting RAM size.
Some boards have a different amount of RAM depending on the HW revision.
Therefore, automatically detecting the RAM size instead of hard-coding it will
reduce the number of device definitions.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-08 17:48:45 +01:00
Álvaro Fernández Rojas
a128904723 bmips: improve CPU frequency patch
Fixes BCM6358 address and calculations.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-08 17:48:45 +01:00
Daniel González Cabanelas
a48ef37747 bcm63xx: AD1018-nor: add NAND flash
The Sercomm AD1018 has a NAND flash. We recently added support for NANDs
in this target.

Use the internal NAND as additional storage.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-03-08 12:45:10 +01:00
Álvaro Fernández Rojas
101491ae4a bmips: dts: comestic changes
Improve and refactor device tree files.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-08 10:42:25 +01:00
Álvaro Fernández Rojas
45180e862c bmips: remove unneeded console from bootargs
console parameter is no longer needed after latest procd update.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-08 10:12:42 +01:00
Álvaro Fernández Rojas
a3b863dc9f bmips: automatically detect CPU frequency
Some BCM63xx SoCs support multiple CPU frequencies depending on HW
configuration.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-08 09:45:32 +01:00
Daniel Golle
7e7218d133 mediatek: remove no longer needed sysupgrade hack
Keeping configuration is now handled in fstools like for other types
of flash as well.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-07 18:27:12 +00:00
Adrian Schmutzler
c6652a7c94 mediatek: mt7622: remove execute bit and shebang from 01_leds
This was added recently and thus overlooked in 85b1f4d8ca
("treewide: remove execute bit and shebang from board.d files").

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 20:23:48 +01:00
Daniel Golle
e991c1b8a2 ipq806x: work-around borked QCA SDK bootloader
The bootloader of many ipq806x boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq806x.
(ipq807x is unaffected as DEVICE_DTS_CONFIG default is set
"config@hk01" in target/linux/ipq807x/image/Makefile)

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-06 19:05:53 +00:00
Daniel Golle
9690836344 ipq40xx: work-around borked QCA SDK bootloader
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-06 19:05:53 +00:00
Daniel Golle
8dd0215676 mediatek: disable RTC on Bananapi R64 and refresh patches
The in-SoC RTC of the Bananapi R64 is more disruptive than useful
without a battery connected. Disable it to not have Linux use the
RTC provided time 2000-01-01 00:00:00 after power-loss.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-06 18:40:04 +00:00
Adrian Schmutzler
9397b22df1 treewide: make AddDepends/usb-serial selective
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 12:38:38 +01:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Ilya Lipnitskiy
b021642cac ramips: 5.10: refresh configs
Run-tested on Ubiquiti EdgeRouter X.

Compile tested on all other subtargets.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
10267e1729 ramips: 5.10: port and refresh patches, ralink drv
Enable testing kernel.

Fix compile errors by using new kernel APIs.

Fix fuzz by manually editing patches to ensure the code goes in the
right place.

For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.

Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.

Run automatic quilt refresh on the rest.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
ef1e652016 ramips: 5.10: rename patches to follow guide
Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.

https://openwrt.org/docs/guide-developer/build-system/use-patches-with-buildsystem#naming_patches

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
3149d8e7be ramips: 5.10: delete upstreamed patches
0098-disable_cm.patch is not needed because upstream fixed CM handling.

The rest are straightforward removals of upstreamed patches.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
eda836e390 ramips: 5.10: copy patches from 5.4
Strict copy, no changes made.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
a9966793e8 ramips: copy config-5.4 to config-5.10
Strict copy, no changes made.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Adrian Schmutzler
cc4ee2eeb4 Revert "ramips: add support for kernel 5.10"
This reverts commit b4aad29a1d.

This was accidentally folded into a single commit. Remove it and
apply it properly again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:23:38 +01:00
Ilya Lipnitskiy
2629d2d5b1 apm821xx, mt7621, oxnas, rockchip, zynq: remove PLUGIN_HOSTCC
This config symbol should not be defined in target configs.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 03:52:33 +00:00
Ilya Lipnitskiy
89744dc741 kernel: generic: filter out CONFIG_PLUGIN_HOSTCC
It appears to be an automatic Kconfig symbol that varies depending on
the host platform. There is no need to define it in target configs, so
filter it out.

Also sort config-filter entries alphabetically.

Cc: Adrian Schmutzler <mail@adrianschmutzler.de>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 03:52:33 +00:00
Ilya Lipnitskiy
b4aad29a1d
ramips: add support for kernel 5.10
Enable testing kernel.

Delete upstreamed patches:
 0098-disable_cm.patch can be dropped, upstream fixed CM handling.

Fix compile errors by using new kernel APIs.

Fix fuzz by manually editing patches to ensure the code goes in the
right place.

For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.

Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.

Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.

Run automatic quilt refresh.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-05 23:55:51 +00:00
Ilya Lipnitskiy
38ba1f9b4c
ramips: 5.4: refresh configs
Automatic refresh by running make kernel_oldconfig on each target.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-05 23:55:46 +00:00
Christian Lamparter
be23f9818a apm821xx: add support for kernel 5.10 for testing
This patch copies over refreshed patches from 5.4.

 - dropped crypto patches (they got upstreamed)

 - dropped renesas USB 3 firmware loader (they got upstreamed)

 - NAND now needs extra device-properties for ECC settings.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2021-03-05 22:47:14 +01:00
Daniel Golle
ca14dfb06b
mediatek: mt7622: bpi-r64: allow MAC addresses to be inherited
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-05 20:13:59 +00:00
Rui Salvaterra
3a187fa718 kernel: bump 5.10 to 5.10.20
Also add a new kconfig symbol (CONFIG_KCMP) to the generic config,
disabling the SYS_kcmp syscall (it was split from
CONFIG_CHECKPOINT_RESTORE, which is disabled by default, so the
previous behaviour is kept).

Removed (upstreamed) patches:
  070-net-icmp-pass-zeroed-opts-from-icmp-v6-_ndo_send-bef.patch
  081-wireguard-device-do-not-generate-ICMP-for-non-IP-pac.patch
  082-wireguard-queueing-get-rid-of-per-peer-ring-buffers.patch
  083-wireguard-kconfig-use-arm-chacha-even-with-no-neon.patch
  830-v5.12-0002-usb-serial-option-update-interface-mapping-for-ZTE-P685M.patch

Manually rebased patches:
  313-helios4-dts-status-led-alias.patch
  104-powerpc-mpc85xx-change-P2020RDB-dts-file-for-OpenWRT.patch

Run tested:
  ath79 (TL-WDR3600)
  mvebu (Turris Omnia)

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-05 20:35:01 +01:00
Rafał Miłecki
8d24da1470 bcm4908: prepare to support TP-Link Archer C2300 V1
It's a BCM4906 based device (2 CPU cores). It has 512 MiB of RAM, 4 LAN
ports, 1 WAN port, 2 USB ports, NAND flash. WiFi unknown at this point.

Flashing is possible using CFE only, proper image will be worked on
later.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-05 14:56:50 +01:00
Ilya Lipnitskiy
fc61a87c29 generic: config-5.10: add missing symbols
Add symbols missing after latest crypto.mk and WireGuard changes.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-05 14:41:14 +01:00
Rui Salvaterra
0eef8402ee kernel: backport GCC 10 usbip build fix for 5.4
From the original commit message:

"With GCC 10, building usbip triggers error for multiple definition
of 'udev_context', in:
- libsrc/vhci_driver.c:18 and
- libsrc/usbip_host_common.c:27.

Declare as extern the definition in libsrc/usbip_host_common.c."

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-05 14:41:14 +01:00
Luis Araneda
1b287ed1a3 kernel: remove symbols from 5.10 no longer present on upstream
REFCOUNT_FULL was removed for linux 5.5:
commit fb041bb7c0a9 (locking/refcount: Consolidate implementations of refcount_t)

COMMON_CLK_VERSATILE was removed on linux 5.8:
commit 5f55f1fb187d (clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE)

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2021-03-05 14:41:14 +01:00
Sieng Piaw Liew
63aad66ddf bcm63xx: rename upstreamed patch
Patch to fix kernel panic was recently accepted upstream so rename patch
and add acked lines to reflect that.

Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
(add the same patch for v5.10)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-05 12:41:45 +01:00
Daniel González Cabanelas
cfa43f8119 kernel: b53: update the BCM5365 UID in the fixup
The BCM5365 UID was updated in the driver, but we should also update it in the
fixup.

Fixes: cbcac4fde8 ("kernel: b53: update the BCM5365 UID")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(Ammend commit description, add Fixes tag)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-05 12:20:48 +01:00
Álvaro Fernández Rojas
bac74aff5e bcm27xx: bcm2711: disable HW_RANDOM_BCM2835
This driver is only present on BCM2708, BCM2709 and BCM2710.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-05 12:13:45 +01:00
Ilya Lipnitskiy
58ad113087 ramips: rename mtk-hsdma to hsdma-mt7621
Follows upstream rename:
https://lore.kernel.org/driverdev-devel/20210130034507.2115280-1-ilya.lipnitskiy@gmail.com/

Fixes ramips builds on 5.4.102

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-04 23:43:02 -10:00
Robert Marko
7f2d9ccd09 ipq40xx: net: phy: qca807x: fix GPIO driver
While rebasing into setting bits instead of magic values,
I accidentally forgot to actually set the force bit.

Without it using the pins as GPIO-s did not actually work.

Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-03-05 00:28:35 +01:00
David Bauer
18a9eff0f6 ath79: enable AT803X PHY for kernel 5.10
The config symbol for the AT803x device driver was lost when adding
kernel 5.10.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-03-05 00:03:57 +01:00
David Bauer
82b9713ce8 ath79: replace chipselect workaround with a proper patch
Debugging the SPI CS issue with kernel 5.10 resulted in a better
understanding for the root cause and a proper patch with a better
explanation.

Exchange the old hack patch with a more efficient (and upstreamable)
solution.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-03-05 00:03:47 +01:00
Jason A. Donenfeld
196f3d586f kernel-5.4: bump to 5.4.102 and refresh patches
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.

This commit involved `update_kernel.sh -v -u 5.4`.

Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-03-04 22:06:53 +01:00
Daniel Golle
1d412235a5 mediatek: mt7622: check firmware metadata
All mt7622 devices except for the UBI-variant of the mt7622-rfb1 carry
metadata appended to the sysupgrade image.
Add it for the mt7622-rfb1-ubi as well and check it on sysupgrade to
avoid accidentally flashing firmware for the wrong device (or variant
or future DEVICE_COMPAT_VERSION).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-04 02:57:19 +00:00
Petr Štetiar
5e0b9dbe8a kernel: generic: add further missing symbols
Compile testing i.mx6 with ALL_KMODS=y, PACKAGE_perf=y and bunch of
tracing/probing symbols has unveiled bunch of missing config options so
add them.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-03-03 22:51:39 +01:00
Petr Štetiar
da6c5b6db2 imx6: add 5.10 as testing kernel
So anyone interested can help with testing.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-03-03 22:51:39 +01:00
Petr Štetiar
26ae69fd03 imx6: refresh kernel config with 5.10 symbols
Just by running `make kernel_oldconfig` and unsetting following options
manually as those cores are cortex-a7 based and thus irrelevant for the
currently default cortex-a9 used cores.

 CONFIG_CLK_IMX6SL is not set
 CONFIG_CLK_IMX6SX is not set
 CONFIG_CLK_IMX6UL is not set

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-03-03 22:51:39 +01:00
Petr Štetiar
354549aaa2 imx6: copy kernel 5.4 config and patches to 5.10
So the changes are visible in the next step. Removed upstreamed patches.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-03-03 22:51:39 +01:00
Oskari Lemmela
60d2623cc5 mediatek: mt7622: change image generation
- set only one EFI system partition
- use shorter path for DEVICE_DTS file

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-03-03 01:00:23 +00:00
Oskari Lemmela
0234881f31 mediatek: mt7622: use ptgen generated MBR header
mt7622 uses MBR partition for booting from SD card.
Add hybrid MBR entry with boot flag after PMBR entry.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-03-03 01:00:23 +00:00
Álvaro Fernández Rojas
05a2fcc1b3 bmips: switch to upstream brcmnand patch
This patch has been accepted upstream for v5.13.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-02 18:05:32 +01:00
Jason A. Donenfeld
1265dbafcd kernel-5.10: backport chacha non block size optimizations
These make a big difference when doing WireGuard with small armv7
routers, and the 5.4 backport already has it.

Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-03-02 10:54:38 +01:00
Jason A. Donenfeld
d540725871 kernel-5.4: backport fd16931a2f51 for chacha neon
Without this patch, the chacha block counter is not incremented on neon
rounds, resulting in incorrect calculations and corrupt packets.

This also switches to using `--no-numbered --zero-commit` so that future
diffs are smaller.

Reported-by: Hans Geiblinger <cybrnook2002@yahoo.com>
Reviewed-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-03-02 09:30:22 +01:00
Rafał Miłecki
b0376462c1 bcm53xx: add support for reading NVRAM based on DT mapping
This is required for devices that use NVRAM data for detecting currently
used firmware partition (e.g. Linksys devices).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-02 09:07:46 +01:00
Daniel Golle
bb98ddc47b mediatek: mt7622: make sure image generation can run in parallel
The previous approach of referencing artifacts in follow-up artifacts
can't work with parallel builds in the current way image.mk is built.
Refactor things so this is not needed.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-02 01:41:31 +00:00
Daniel Golle
a3288c35ef mediatek: mt7622: blue LED should be active high as well
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-01 21:46:38 +00:00
Daniel Golle
2151d89713 mediatek: mt7622: bpi-r64: fix sysupgrade on empty disk
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-01 19:35:08 +00:00
Daniel Golle
ded54ae196 mediatek: mt7622: bpi-r64: simplify eMMC install procedure
Write everything needed for eMMC install into the gaps between
partitions on SD card. In that way, installation to eMMC only needs
the SD card, no additional files need to be loaded via TFTP any more.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-01 19:33:46 +00:00
Rafał Miłecki
7a7b2fd809 kernel: add the latest mtd patch extending ofpart parser
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).

It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-01 18:18:38 +01:00
Álvaro Fernández Rojas
584ce6b2a0 bmips: switch to upstream SMP CPU mappings patch
The patch has been accepted upstream with some minor modifications.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-01 17:26:59 +01:00
Daniel Golle
8e7392b18e mediatek: mt7622: enable CONFIG_SPI_MTK_NOR
Somehow this got disabled in the transition to 5.10.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-01 11:57:08 +00:00
Daniel Golle
aaa0203ad4 mediatek: mt7622: rename mt7622-ubi to mt7622-rfb1-ubi
This profile is meant to be used on MT7622 rfb1 AP, indicate that in
the name to make things less confusing.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-03-01 11:57:02 +00:00
Rafał Miłecki
acbea54bc2 bcm4908: backport Ethernet driver fixes from the 5.12
The most noticeable one is fix for RX stopping on high traffic.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-03-01 08:15:48 +01:00
Daniel Golle
ebcb4f1d0a
treewide: fix spelling 'seperate' -> 'separate'
This popular spelling mistake was also introduced by myself lately.
Fix it everywhere.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 23:59:21 +00:00
Pawel Dembicki
0d062b6246 mpc85xx: p2020: Fix nand driver probe
At this moment driver start fail with error:
[    3.771991] fsl,elbc-fcm-nand: probe of ffa00000.nand failed with error -22

elbc-fcm-nand driver use legacy method of ecc mode detection. It detect hw/sw
ecc mode when system configure it to "none". [1]

This patch adds 'nand-ecc-mode = "none"' propoerty to use generic driver
ecc mode detection.

[1] https://elixir.bootlin.com/linux/v5.10.18/source/drivers/mtd/nand/raw/fsl_elbc_nand.c#L730

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-03-01 00:34:23 +01:00
Pawel Dembicki
1d3b1171ae mpc85xx: add testing kernel 5.10
Subtargets p1010 and p1020 have already added.

Compile and run tested on: P2020RDB

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-03-01 00:34:23 +01:00
Pawel Dembicki
76649fd06d mpc85xx: p2020: fix cfi-nor detection
At this moment p2020rdb has broken images, because NOR memory connected
to eLBC bus isn't detected.

In 642b1e8dbed7 linux tree commit, config dependencies of MTD_PHYSMAP_OF
was changed and now MTD_PHYSMAP is required.

This patch adds MTD_PHYSMAP option to kernel config in p2020 subtarget
and fix booting of p2020rdb.

Fixes: 13b1db795f ("mpc85xx: add support for kernel 5.4")

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-03-01 00:34:23 +01:00
Alberto Bursi
788ec9a7cf x86: add support for AWS T3 instances
Amazon AWS T3 cloud instances require kernel support
for the Elastic Fabric Adapter to access storage
and for Elastic Network Adapter to use network
interfaces.

Since the Fabric Adapter is needed to access
root filesystem, enable in x86_64 kernel.

Elastic Network Adapter goes in a module,
and add this module to default list in x86_64.
The module is set to AutoLoad because AutoProbe does
not seem to load it.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2021-03-01 00:34:23 +01:00
Shiji Yang
df1e5d6463 ramips: fix partition layout of hiwifi hc5x61
Changes:
 * Increase "oem" partition size from 0x10000 to 0x20000
 * Correct partition lables, synchronize with official firmware

Evidence:
It should be the same as hiwifi hc5x61a and the fact indeed the
case. Here is part of dmesg boot log read from official firmware:
[    1.470000] Creating 7 MTD partitions on "raspi":
[    1.470000] 0x000000000000-0x000000030000 : "u-boot"
[    1.480000] 0x000000030000-0x000000040000 : "hw_panic"
[    1.490000] 0x000000040000-0x000000050000 : "Factory"
[    1.490000] 0x000000fc0000-0x000000fe0000 : "oem"
[    1.500000] 0x000000fe0000-0x000000ff0000 : "bdinfo"
[    1.510000] 0x000000ff0000-0x000001000000 : "backup"
[    1.510000] 0x000000050000-0x000000fc0000 : "firmware"

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-03-01 00:34:23 +01:00
Rui Salvaterra
6fe6b631ef mvebu/omnia: fix the device tree
Backport [1] and fix [2] hardware buffer management. Also fix the IRQ storm
caused by a misconfiguration of the PCA9538 interrupt pin [3].

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm/boot/dts/armada-385-turris-omnia.dts?id=018b88eee1a2efda26ed2f09aab33ccdc40ef18f
[2] https://lore.kernel.org/linux-arm-kernel/20210217153038.1068170-1-rsalvaterra@gmail.com/
[3] https://lore.kernel.org/linux-arm-kernel/20210220231144.32325-1-kabel@kernel.org/

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-03-01 00:34:22 +01:00
Mathias Kresin
5662f5b114 lantiq: vr9: set the usb led trigger via devicetree
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds.

Drop the now unused userspace helper code as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-01 00:19:58 +01:00
Mathias Kresin
23dd786734 lantiq: set maximum kernel size
These boards have a fixed size kernel partition but do not limit the
kernel size during image building.

Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-03-01 00:19:58 +01:00
Mathias Kresin
7995a93744 lantiq: ARV752DPW22: set the usb led trigger via devicetree
Assign the usbdev trigger via devicetree and drop the userspace
handling of the usb leds

Add the PCI attached usb controller as trigger sources for the usb led
as well.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-03-01 00:19:58 +01:00
Adrian Schmutzler
cfd1a40583 octeon: re-enable CONFIG_CAVIUM_CN63XXP1 and EdgeRouter image
The symbol CONFIG_CAVIUM_CN63XXP1 was disabled during the bump to
4.19 (see Fixes:) with the following reason:

  No supported hardware uses CN63XXP1 and it causes "slight decrease
  in performance"

However, it later turned out that the edgerouter image needed it,
which led to having the device disabled in [1].
Still, dropping support of a device seems a harsh action for just
removing a "slight" decrease in performance from the other devices.

Thus, this enables CONFIG_CAVIUM_CN63XXP1 again, and essentially
restores the situation present until (including) kernel 4.14 on
this target.

For OpenWrt as a platform, it seems more desirable to support all
devices (and have them tested regularly via the snapshots) in this
case.
Users interested in maximum performance might still just remove
the symbol again in their local build.

[1] 3824fa26d2 ("octeon: disable edgerouter image")

Fixes: 6c22545225 ("target/octeon: Add Linux 4.19 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-28 21:55:22 +01:00
Adrian Schmutzler
5ad49ca029 octeon: refresh config for kernel 5.4
Simple run of 'make kernel_oldconfig'

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-28 21:55:22 +01:00
David Bauer
024c81adb8 mediatek: add missing 5.10 patches
These patches are required for the Ubiquiti UniFi 6 LR to work. They
were already present for kernel 5.4 but got lost when adding 5.10
support.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-28 12:17:48 +01:00
Daniel Golle
dfa0a38d1f mediatek: rework support for BananaPi BPi-R64
**What's new**

 * Bring support for the Bananapi BPi-R64 to the level desirable for
   a nice hackable routerboard.
 * Use ARM Trusted Firmware A from source. (goodbye binary preloader)
 * Use Das U-Boot from source. (see previous commit)
 * Assemble SD-card image using OpenWrt image-commands.
   (no gen_sd_cruz_foo.sh added, this is not Raspbian)
 * Updated kernel options to support root filesystem.
 * Updated DTS to match OpenWrt LAN ports, known LEDs, buttons, ...
 * Detect root device, handle sysupgrade, config restore, ...
 * Wire up (known) LEDs and buttons in OpenWrt-fashion.
 * Build one set of images from SD-card and eMMC.
 * Hopefully provide a good example of how things can be done right
   from scratch.

**Installation and images**

 * Have an empty SD-card at hand
 * Write stuff to the card, as root (card device is /dev/mmcblkX)
   - write header, gpt, bl2, atf, u-boot and recovery kernel:
     `cat *bpi-r64-boot-sdcard.img *bpi-r64-initramfs-recovery.fit > /dev/mmcblkX`
   - rescan partitions:
     `blockdev --rereadpt /dev/mmcblkX`
   - write main system to production partition:
     `cat *bpi-r64-squashfs-sysupgrade.fit > /dev/mmcblkXp5`

 * Installation to eMMC works using SD-card bootloader via TFTP
   When running OpenWrt of SD-card, issue this to trigger installation
   to eMMC:
   `fw_setenv bootcmd run emmc_init`
   Be prepared to serve the content of bin/targets/mediatek/mt7622 on
   TFTP server address 192.168.1.254.

**What's missing**

 * The red LED is always on, probably a hardware bug.
 * AHCI (probably needs DTS changes)
 * Ship SD-card image ready with every needed for eMMC install.
 * The eMMC has a second, currently unused boot partition. This would
   be ideal to store the WiFi EEPROM and Ethernet MAC address(es).
   @sinovoip ideas?

Thanks to Thomas Hühn @thuehn for providing the hardware!

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 04:15:44 +00:00
Daniel Golle
0235186182 mediatek: add alternative UBI NAND layout for Linksys E8450
The vendor flash layout of the Linksys E8450 is problematic as it uses
the SPI-NAND chip without any wear-leveling while at the same time
wasting a lot of space for padding.
Use an all-UBI layout instead, storing the kernel+dtb+squashfs in
uImage.FIT standard format in UBI volume 'fit', the read-write
overlay in UBI volume 'rootfs_data' as well as reduntant U-Boot
environments 'ubootenv' and 'ubootenv2', and a 'recovery'
kernel+dtb+initramfs uImage.FIT for dual-boot.

** WARNING **
THIS PROCEDURE CAN EASILY BRICK YOUR DEVICE PERMANENTLY IF NOT CARRIED
OUT VERY CAREFULLY AND EXACTLY AS DESCRIBED!

Step 0

 * Configure your PC to have the static IPv4 address 192.168.1.254/24
 * Provide bin/targets/mediatek/mt7622 via TFTP

Now continue EITHER with step 1A or 1B, depending on your preference
(and on having serial console wired up or not).

Step 1A (Using the vendor web interface (or non-UBI OpenWrt install))

In order to update to the new bootloader and UBI-based firmware,
use the web browser of your choice to open the routers web-interface
accessible on http://192.168.1.1

 * Navigate to
   'Configuration' -> 'Administration' -> 'Firmware Upgrade'

 * Upload the file
    openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb
   and proceed with the upgrade.

 * Once OpenWrt comes up, use SCP to upload the new bootloader files to
   /tmp on the router:
    *-mt7622-linksys_e8450-ubi-preloader.bin
    *-mt7622-linksys_e8450-ubi-bl31-uboot.fip

 * Connect via SSH as you will now need to replace the bootloader in
   the Flash.

    ssh root@192.168.1.1
    (the usual warnings)

 * First of all, backup all the flash now:

    for mtd in /dev/mtdblock*; do
     dd if=$mtd of=/tmp/$(basename $mtd);
    done

 * Then use SCP to copy /tmp/mtdblock* from the router and keep them
   safe. You will need them should you ever want to return to the
   factory firmware!

 * Now flow the uploaded files:
    mtd -e /dev/mtd0 write /tmp/*linksys_e8450-ubi-preloader.bin /dev/mtd0
    mtd -e /dev/mtd1 write /tmp/*linksys_e8450-ubi-bl31-uboot.fip /dev/mtd1

   If and only if both writes look like the completed successfully
   reboot the router. Now continue with step 2.

Step 1B (Using the vendor bootloader serial console)

 * Use the serial to backup all /dev/mtd* devices before using the
   stock firmware (you got root shell when connected to serial).

 * Then reboot and select 'U-Boot Console' in the boot menu.

 * Copy the following lines, one by one:

tftpboot 0x40080000 openwrt-mediatek-mt7622-linksys_e8450-ubi-preloader.bin
tftpboot 0x40100000 openwrt-mediatek-mt7622-linksys_e8450-ubi-bl31-uboot.fip
nand erase 0x0 0x180000
nand write 0x40080000 0x0 0x180000
reset

Now continue with step 2

Step 2

Once the new bootchain comes up, the loader will initialize UBI and the
ubootenv volumes. It will then of course fail to find any bootable
volume and hence resort to load kernel via TFTP from server
192.168.1.254 while giving itself the address 192.168.1.1

The requested file is called
openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb
and your TFTP server should provide exactly that :)
It will be written to UBI as recovery image and booted.
You can then continue and flash the production OS image, either
by using sysupgrade in the booted initramfs recovery OS, or by using
the bootloader menu and TFTP.

That's it. Go ahead and mess around with a bootchain built almost
completely from source (only DRAM calibration blobs are fitted in bl2,
and the irreplacable on-chip ROM loader remains, of course).
And enjoy U-Boot built with many great features out-of-the-box.

You can access the bootloader environment from within OpenWrt using the
'fw_printenv' and 'fw_setenv' commands. Don't be afraid, once you got
the new bootchain installed the device should be fairly unbrickable
(holding reset button before and during power-on resets things and
allows reflashing recovery image via TFTP)

Special thanks to @dvn0 (Devan Carpenter) for providing amazingly fast
infra for test-builds, allowing for `make clean ; make -j$(nproc)` in
less than two minutes :)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 01:23:48 +00:00
John Crispin
aa94e34c1d mediatek: add Linksys E8450 support
The Linksys E8450, also known as Belkin RT3200, is a dual-band
IEEE 802.11bgn/ac/ax router based on MediaTek MT7622BV and
MediaTek MT7915AN chips.

FCC: K7S-03571 and K7S-03572

Hardware highlights:
 - CPU: MediaTek MT7622BV (2x ARM Cortex-A53 @ 1350 MHz max.)
 - RAM: 512MB DDR3
 - Flash: 128MB SPI-NAND (2k+64)
 - Ethernet: MT7531BE switch with 5 1000Base-T ports
             CPU port connected with 2500Base-X
 - WiFi 2.4 GHz: 802.11bgn 4T4R built-in antennas
                 MT7622VB built-in
 - WiFi   5 GHz: 802.11ac/ax 4T4R built-in antennas
                 MT7915AN chip on-board via PCIe
                 MT7975AN front-end
 - Buttons: Reset and WPS
 - LEDS: 3 user controllable LEDs, 4 wired to switch
 - USB: USB2.0, single port
 - no Bluetooth (supported by SoC, not wired on board)
 - Serial: JST PH 2.0MM 6 Pin connector inside device
            ----_____________----
           [  GND RX - TX  -  -  ]
            ---------------------
 - JTAG:   unpopulated ARM JTAG 20-pin connector (works)

This commit adds support for the device in a way that is compatible
with the vendor firmware's bootloader and dual-boot flash layout, the
resulting image can directly be flashed using the vendor firmware.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-02-28 01:20:53 +00:00
Felix Fietkau
7a6d074824 kernel: add support for enabling fit firmware partition parser via cmdline
This is useful for dual-boot setups where the loader sets variables depending
on the flash boot partition.
For example the Linksys E8450 sets mtdparts=master for the first partition
and mtdparts=slave for the second one.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-02-28 00:46:11 +00:00
Felix Fietkau
e230345bbc mediatek: add support for configuring BMT table size via device tree
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-02-28 00:46:11 +00:00
Felix Fietkau
c46ccb69d1 mediatek: mt7622: add Linux 5.10 support
Switch mt7622 subtarget to Linux 5.10, it has been tested by many of us
on several devices for a couple of weeks already.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-02-28 00:45:56 +00:00
Felix Fietkau
11425c9de2 mediatek: implement bad-block management table support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-02-28 00:09:09 +00:00
Daniel Golle
6b0295a47d image: extend FIT partition parser for use on eMMC/SDcard
Introduce a magic GUID_PARTITION_LINUX_FIT_GUID to designate a GPT
partition to be interpreted by the FIT partition parser.
In that way, sub-partitions for (external-data) uImage.FIT stored
directly in a partition can be split, similar like we do for devices
with raw flash storage.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-28 00:09:09 +00:00
Jason A. Donenfeld
2a27f6f90a kernel: backport pending fix to select CPU_MIPS64
The CPU_MIPS64 and CPU_MIPS32 variables are supposed to be able to
distinguish broadly between 64-bit and 32-bit MIPS CPUs. However, they
weren't selected by the specialty CPUs, Octeon and Loongson, which meant
it was possible to hit a weird state of:

   MIPS=y, CONFIG_64BIT=y, CPU_MIPS64=n

This commit rectifies the issue by having CPU_MIPS64 be selected when
the missing Octeon or Loongson models are selected.

In particular, this affects our octeonplus target.

It has been posted to LKML here:
https://lore.kernel.org/linux-mips/20210227122605.2680138-1-Jason@zx2c4.com/

Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-02-27 19:14:27 +01:00
John Audia
a1735fe73c kernel: bump 5.4 to 5.4.101
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional.

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-27 16:51:52 +01:00
Aleksander Jan Bajkowski
598de0f41c kernel: move some new symbols available on 5.10 to generic
Move some disabled config options found in sunxi target to generic.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-02-27 16:49:02 +01:00
Daniel González Cabanelas
cbcac4fde8 kernel: b53: update the BCM5365 UID
BCM63XX internal PHYs and BCM5365 SoC internal switch are both using the
same phy_driver->phy_id, causing conflicts and unnecessary probes. E.g
the BCM63XX phy internal IRQ is lost on the first probe.

The full BCM5365 UID is 0x00406370.

Use an additional byte to mask the BCM5365 UID to avoid duplicate driver
phy_id's. This will fix the IRQ issue in internal BCM63XX PHYs and avoid
more conflicts in the future.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-02-26 21:11:19 +01:00
Ilya Lipnitskiy
23b801d3ba kernel: 5.4: generic: add missing symbols
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-02-26 20:41:01 +01:00
Ilya Lipnitskiy
3500fd7938 kernel: 5.4: fix patches after wireguard backport
No major problems, just a minor Kconfig fix and a refresh.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-02-26 20:41:01 +01:00
Jason A. Donenfeld
3888fa7880 kernel: 5.4: import wireguard backport
Rather than using the clunky, old, slower wireguard-linux-compat out of
tree module, this commit does a patch-by-patch backport of upstream's
wireguard to 5.4. This specific backport is in widespread use, being
part of SUSE's enterprise kernel, Oracle's enterprise kernel, Google's
Android kernel, Gentoo's distro kernel, and probably more I've forgotten
about. It's definately the "more proper" way of adding wireguard to a
kernel than the ugly compat.h hell of the wireguard-linux-compat repo.
And most importantly for OpenWRT, it allows using the same module
configuration code for 5.10 as for 5.4, with no need for bifurcation.

These patches are from the backport tree which is maintained in the
open here: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y
I'll be sending PRs to update this as needed.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
2021-02-26 20:41:01 +01:00
Jason A. Donenfeld
7d4143234c kernel: 5.10: wireguard: backport 5.12-rc1 changes in net.git
These will eventually make their way to 5.10, but it could be a while.

https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=ee576c47db60432c37e54b1e2b43a8ca6d3a8dca
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=5a0598695634a6bb4126818902dd9140cd9df8b6
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=99fff5264e7ab06f45b0ad60243475be0a8d0559
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=8b5553ace83cced775eefd0f3f18b5c6214ccf7a
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=bce2473927af8de12ad131a743f55d69d358c0b9

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[Rename 082-wireguard-kconfig... to 083-wireguard-kconfig...]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-02-26 20:41:00 +01:00
Ilya Lipnitskiy
7d00f632b7 zynq: Enable CONFIG_KERNEL_MODE_NEON
This flag is set on all other platforms. And Zynq 7000 SoC does have
NEON support:
https://www.xilinx.com/support/documentation/application_notes/xapp1206-boost-sw-performance-zynq7soc-w-neon.pdf

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-02-26 20:41:00 +01:00
David Bauer
cc2d61edc3 mpc85xx: remove fdt.bin image
When converting the fdt binary to be created as an artifact, the image
receipt was dropped but the entry in the target images list was not.

Fixes commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage")

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-26 15:35:41 +01:00
Lech Perczak
59d065c9f8 ramips: add support for ZTE MF283+
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.

Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
  switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
  internally wired in parallel by 0-Ohm resistors, handled entirely by
  internal WWAN modem.
- USB: internal miniPCIe slot for modem,
  unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
  pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
  settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
  phone (bicolor, controlled by modem), Signal,
  4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.

Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.

There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.

(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
  omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
  like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
  persistent environment for next installation.
- If you ever might want to return to vendor firmware,
  BACK UP CONTENTS OF YOUR FLASH NOW.
  For this router, commonly used by mobile networks,
  plain vendor images are not officially available.
  To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
  most important, and copy them over network to your PC. But in case
  anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
  and execute sysupgrade.

(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
  (no quotes), for example using tftpd:
  cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
  5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
  minute.

Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery

(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
  installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
  your backup taken before OpenWrt installation, and /dev/mtd3 is the
  "firmware" partition.

(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
  with firmware backup you took during installation, or by vendor
  firmware obtained elsewhere.

A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
  despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
  WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
  for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
  modem, so it work independently of OpenWrt.
  Tested to work even before OpenWrt booted.
  I managed to open up modem's shell via ADB,
  and found from its kernel logs, that FXS and its LED is indeed controlled
  by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
  each and every one of them manually, so this might not be complete -
  it looks like bicolor LED is used for FXS, possibly to support
  dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
  read command, due to using 4k sectors throughout the target. I decided
  to keep it at the moment, to avoid breaking existing devices - I
  identified one potentially affected, should this be limited to under
  4MB of Flash. The difference between sysupgrade durations is whopping
  3min vs 8min, so this is worth pursuing.

In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.

Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.

A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
  submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
  uqmi did connect successfully, once I selected correct PDP context
  type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
  added to 51-android.rules like so:

SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"

While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:54 +01:00
Jeff Collins
6e0c780eb3 mvebu: add LED support for GL.iNet GL-MV1000
This patch enables LED support for the GL.iNet GL-MV1000

Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:50 +01:00
Tom Stöveken
a6f7268dc7 ath79: fix USB power on TP-Link TL-WR810N v1
Before: Kernel reported "usb_vbus: disabling" and the USB was not
        providing power
After:  USB power is switched on, peripheral is powered from the
        device

Signed-off-by: Tom Stöveken <tom@naaa.de>
[squash and tidy up]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:02 +01:00
Rafał Miłecki
8078d89a53 bcm53xx: backport more upstream dts stuff from kernel 5.11
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-25 21:17:38 +01:00
Vivek Unune
39ed2265dd bcm53xx: backport Linksys Panamera (EA9500) patches
These patches have been already accepted.

302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch had to
be updated.

[rmilecki: use actual upstream accepted patches
           replace v5.10 with v5.11 to match actual upstream kernel
           recover dropped part of the pinctrl compatible patch
           update filenames
           refresh patches]

Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-25 21:17:38 +01:00
Rafał Miłecki
d0ee398c36 bcm53xx: group dts backports by upstream kernel version
It's a simple renaming thing.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-25 21:17:38 +01:00
Álvaro Fernández Rojas
c919f7408d bmips: dts: fix syscon-reboot nodes
Using regmap with phandles is deprecated.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-25 20:40:02 +01:00
Álvaro Fernández Rojas
5c223fb43f bmips: add BCM63268 timer clock and reset support
We need this to fix USB support on BCM63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-25 20:40:02 +01:00
Álvaro Fernández Rojas
e2448e5e03 bmips: rewrite pin controllers
This is needed in order to upstream them.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-25 20:40:02 +01:00
Adrian Schmutzler
ef2cb8572b treewide: rename IMAGE_PREFIX/IMAGE_NAME to DEVICE_IMG_*
We so far had two variables IMG_PREFIX and IMAGE_PREFIX with
different content. Since these names are obviously quite
confusing, this patch renames the latter to DEVICE_IMG_PREFIX,
as it's a device-dependent variable, while IMG_PREFIX is only
(sub)target-dependent.

For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as
that's a device-dependent variable as well.

Cc: Paul Spooren <mail@aparcar.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-25 18:11:06 +01:00
Daniel Golle
198385b69d mediatek: switch to use seperate ramdisk for initramfs images
MediaTek targets always use U-Boot's modern uImage.FIT format which
allows bundling several blobs into a single file including hashes,
descriptions and more. In fact, we are already using that to bundle
the Flattened Device Tree blob with the kernel on this and many
other targets.
In the same fashion, we can now make use of the newly introduced
support for building seperate ramdisk to uImage.FIT with a dedicated
initrd blob checked and loaded by U-Boot instead of embedding the
cpio archive into the kernel itself.
This allows for having larger ramdisks, choosing ramdisk compression
independently of kernel compression (while only kernel is decompressed
by the bootloader) and for more easily replacing or modifying the
filesystem contained in an initramfs image.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-25 16:39:55 +00:00
Daniel Golle
45c0e0ee41 oxnas: add experimental support for Linux 5.10
PCIe still reports link-down for some reason, RAID fails to assemble
despite SATA looking good (maybe a generic problem with RAID?)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-25 16:39:55 +00:00
Adrian Schmutzler
722f1bd549 ath79: enable UART node for GL-USB150
This was overlooked when adding support for this device.
(It has recently been discovered that this was the only device in
ath79 having &uart disabled.)

Fixes: acc6263013 ("ath79: add support for GL.iNet GL-USB150")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-25 15:12:05 +01:00
John Audia
4b92663f7a kernel: bump 5.4 to 5.4.100
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-25 13:08:09 +01:00
Oskari Lemmela
f0818706eb mediatek: mt7622-bananapi-bpi-r64-rootdisk rebase to upstream dts
simplify maintaining mt7622-bananapi-bpi-r64-rootdisk.dts by
storing only differences between upstream dts

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Oskari Lemmela
7befce2bb1 mediatek: mt7622: fix bpi-r64 emmc f2fs overlay
f2fs tools are needed for generating f2fs overlay.
vfat modules are used for recovery mounting.

Fixes: f72a2b004c ("mediatek: add bpi-r64 emmc support")
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Oskari Lemmela
ec2fca7c65 mediatek: mt7622: enable support for f2fs overlay
f2fs filesystem and loop device support are needed for f2fs
overlay over squashfs.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Oskari Lemmela
567a5f7739 mediatek: mt7622: add missing CONFIG_MMC_BLK
CONFIG_MMC_BLK enables block devices for SD/eMMC

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Kabuli Chana
dc8cc44612 kernel: bump version 5.10 to 5.10.18
update kernel version, refresh current patchset

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
[rebase/refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 18:45:59 +01:00
Álvaro Fernández Rojas
a0eff5ddff bmips: add SPI accepted PM patches
These patches have been accepted upstream.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-24 18:20:04 +01:00
Adrian Schmutzler
9b37db5caa ath79: create common DTSI for Senao qca955x APs
This creates a shared DTSI for qca955x Senao/Engenius APs with
concatenated firmware partition/okli loader:

 - EAP1200H
 - EnstationAC v1

To make this usable for future boards with 32 MB flash as well,
split the partitions node already.

Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 14:08:30 +01:00
Michael Pratt
70bf4a979c ath79: rename 'engenius' Makefile definitions to 'senao'
These recipes and definitions can apply
to devices from other vendors
with PCB boards or SDK produced by Senao
not only the brand Engenius

possible examples:
Extreme Networks, WatchGuard, OpenMesh,
Fortinet, ALLNET, OCEDO, Plasma Cloud, devolo, etc.

so rename all of these items
and move DEVICE_VENDOR from common to generic/tiny.mk

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-02-24 14:08:30 +01:00
Adrian Schmutzler
ce8b535ed3 ath79: create common DTSI for Senao ar934x APs
This creates a shared DTSI for ar934x Senao/Engenius APs:

 - EAP300 v2
 - ENS202EXT v1
 - EAP600
 - ECB600

Since ar9341/ar9344 have different configuration, this new file
mostly contains the partitioning.

Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Adrian Schmutzler
4204d70d7a ath79: create common DTSI for Senao ar724x APs
This creates a shared DTSI for ar724x Senao/Engenius APs:

 - ENH202 v1
 - EAP350 v1
 - ECB350 v1

Since ar7240/ar7242 have different configuration, this new file
mostly contains the partitioning.

Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Adrian Schmutzler
3a4b751110 ath79: enable UART in SoC DTSI files
The uart node is enabled on all devices except one (GL-USB150 *).
Thus, let's not have a few hundred nodes to enable it, but do not
disable it in the first place.

Where the majority of devices is using it, also move the serial0
alias to the DTSI.

*) Since GL-USB150 even defines serial0 alias, the missing uart
   is probably just a mistake. Anyway, disable it for now so this
   patch stays cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Sungbo Eo
1322150b0c kirkwood: set testing kernel version to 5.10
Tested on Pogoplug V4.

Linksys EA3500 will not build with buildbot settings and should be
disabled when the target is switched, unless the image size is
reduced again.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add EA3500 comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Sungbo Eo
1bb3f593ee kirkwood: update config for kernel 5.10
Update config with make kernel_oldconfig.

CONFIG_SATA_PMP=y is added manually as done for 5.4.
This should be resolved properly in a separate issue.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add back CONFIG_SATA_PMP, rebase/refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Sungbo Eo
58ebc50724 kirkwood: refresh patches for kernel 5.10
Refresh patches to make them apply to kernel 5.10.
The removed patch has been merged upstream.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-24 02:53:53 +01:00
Sungbo Eo
e464d365fe kirkwood: copy files to kernel 5.10
Copy config and patches to kernel 5.10.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-24 02:53:53 +01:00
Adrian Schmutzler
8d766aa669 kernel: add further missing symbols
CONFIG_NET_DSA_MV88E6XXX_PTP was simply missing in generic config.

CONFIG_I2C_PXA_SLAVE was previously enabled via i2c-pxa package,
but got removed there without moving the symbol to generic config.

Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Daniel Golle
330bd380e8 image: allow building FIT and uImage with ramdisk
Instead of embedding the initrd cpio archive into the kernel, allow
for having an external ramdisk added to the FIT or uImage.
This is useful to overcome kernel size limitations present in many
stock bootloaders, as the ramdisk is then loaded seperately and doesn't
add to the kernel size. Hence we can have larger ramdisks to host ie.
installers with all binaries to flash included (or a web-based
firmware selector).
In terms of performance and total size the differences are neglectible.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 01:35:20 +00:00
Daniel Golle
e6aac8d98f image: add support for building FIT image with filesystem
Allow for single (external-data) FIT image to hold kernel, dtb and
squashfs. In that way, the bootloader verifies the system integrity
including the rootfs, because what's the point of checking that the
hash of the kernel is correct if it won't boot in case of squashfs
being corrupted? Better allow bootloader to check everything needed
to make it at least up to failsafe mode. As a positive side effect
this change also makes the sysupgrade process on nand potentially
much easier as it is now.
In short: mkimage has a parameter '-E' which allows generating FIT
images with 'external' data rather than embedding the data into the
device-tree blob itself. In this way, the FIT structure itself remains
small and can be parsed easily (rather than having to page around
megabytes of image content). This patch makes use of that and adds
support for adding sub-images of type 'filesystem' which are used to
store the squashfs. Now U-Boot can verify the whole OS and the new
partition parsers added in the Linux kernel can detect the filesystem
sub-images, create partitions for them, and select the active rootfs
volume based on the configuration in FIT (passing configuration via
device tree could be implemented easily at a later stage).

This new FIT partition parser works for NOR flash (on top of mtdblock),
NAND flash (on top of ubiblock) as well as classic block devices
(ie. eMMC, SDcard, SATA, NVME, ...).
It could even be used to mount such FIT images via `losetup -P` on a
user PC if this patch gets included in Linux upstream one day ;)

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 01:35:20 +00:00
DENG Qingfang
06af45ec05 ramips: remove obsolete mx25l25635f compatible hack
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2021-02-24 00:30:40 +01:00
Stijn Segers
06356f0020 ramips: overwrite reset gpio properties in DIR-860L DTS
As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the
DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1)
on PCI-E port 1 comes up reliably.

Fixes the following error that popped up in dmesg:

    [    1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
2021-02-23 21:10:56 +01:00
Sander Vanheule
773949c152 ramips: mt7621: enable SX150x driver
The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO
expander controlling the device LEDs. This expander was initially
supported on 4.14, but support was lost in the transition to 5.4.

Since this driver cannot be built as a kernel module, enable it in the
kernel config for all mt7621 devices.

Run-tested on a Netgear R6800.

Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2021-02-23 21:10:56 +01:00
DENG Qingfang
920eaab1d8 kernel: DSA roaming fix for Marvell mv88e6xxx
Marvell mv88e6xxx switch series cannot perform MAC learning from
CPU-injected (FROM_CPU) DSA frames, which results in 2 issues.
- excessive flooding, due to the fact that DSA treats those addresses
as unknown
- the risk of stale routes, which can lead to temporary packet loss

Backport those patch series from netdev mailing list, which solve these
issues by adding and clearing static entries to the switch's FDB.

Add a hack patch to set default VID to 1 in port_fdb_{add,del}. Otherwise
the static entries will be added to the switch's private FDB if VLAN
filtering disabled, which will not work.

The switch may generate an "ATU violation" warning when a client moves
from the CPU port to a switch port because the static ATU entry added by
DSA core still points to the CPU port. DSA core will then clear the static
entry so it is not fatal. Disable the warning so it will not confuse users.

Link: https://lore.kernel.org/netdev/20210106095136.224739-1-olteanv@gmail.com/
Link: https://lore.kernel.org/netdev/20210116012515.3152-1-tobias@waldekranz.com/
Ref: https://gitlab.nic.cz/turris/turris-build/-/issues/165
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2021-02-23 21:10:56 +01:00
Adrian Schmutzler
5e9b07ff36 kernel: add symbol CONFIG_POWER_RESET_LINKSTATION
Add symbol to generic config (this was added between 5.4 and 5.10),
and remove it from the targets where it was added by kernel_oldconfig
in the meantime.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 21:08:21 +01:00
David Bauer
55ed4bf6d7 generic: add missing symbols
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-23 20:13:37 +01:00
Shiji Yang
d1176ad95a ramips: improve gpio control for Phicomm PSG1218
Description:
1. From key and led config setting, we can find only "uartf" and "i2c" are used
as gpio by check mt7620 datasheet. It's time to remove unused pin group.

2. PSG1218 only have three led, so we can remove ethernet led pinctrl. refer to
Phicomm K2G.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-02-23 18:31:35 +01:00
Rui Salvaterra
fde9703a48 mvebu: add 5.10 as a testing kernel
Keep 5.4 as stable until further validation.

Tested on Turris Omnia (Rui Salvaterra) and ESPRESSObin v5 (Tomasz
Maciej Nowak). Cortex-A{53,72} subtargets are only build-tested.

Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[added comment about tests]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 18:31:35 +01:00
Rui Salvaterra
b0cdc5ae46 mvebu: fix the Turris Omnia device tree
Enable and fix hardware buffer management. Also fix the IRQ storm caused by a
misconfiguration of the PCA9538 interrupt pin.

Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-02-23 18:31:35 +01:00
Rui Salvaterra
23ebb2e9c3 mvebu: fix the patch numbering
Make each logical patch group numbering contiguous.

Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add kernel version to backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 18:31:35 +01:00
Rui Salvaterra
b43f5a9359 mvebu: refresh 5.10 kconfigs/patches
Also delete already upstreamed patches/changes.

Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-02-23 18:31:35 +01:00
Adrian Schmutzler
7be8ab4f7b mvebu: remove upstreamed DTS files in 5.10
Some armada-3720-espressobin-* files have been upstreamed, move
these to files-5.4.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 18:31:35 +01:00
Rui Salvaterra
202515b901 mvebu: copy 5.4 patches/kconfigs to 5.10
Just a simple copy, no refresh yet.

Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[do not duplicate files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 18:31:35 +01:00
Rui Salvaterra
4d9ae8ca07 mvebu: refresh the 5.4 kernel configs
Remove the implicit/inherited symbols. While not strictly necessary, this will
make reviewing the diff between 5.4 and 5.10 easier.

Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-02-23 18:31:35 +01:00
Rui Salvaterra
dc6ac62046 kernel: 5.10: add further generic kconfig symbols
This will make the specific kconfig smaller.

Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[improved commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 18:31:35 +01:00
Álvaro Fernández Rojas
4dd5845f49 bmips: fix SMP CPU mapping
SMP isn't supported on BCM6358 since it has a shared TLB. Some boards boot
with CPU #1 instead of CPU #0, and this is currently not supported do to a
smp-bmips bug.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-23 15:25:13 +01:00
Álvaro Fernández Rojas
c015d18cd7 bmips: switch to accepted upstream patch
This patch has been accepted and is going to be in linux v5.12.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-23 15:22:27 +01:00
Álvaro Fernández Rojas
de3066bef7 bmips: rename upstream patches
These patches were applied in linux v5.11, not v5.12.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-23 15:14:41 +01:00
Álvaro Fernández Rojas
fc2a4e5682 bmips: bcm6358: add watchdog
Watchdog node was missing in commit 029093a302.

Fixes: 029093a302 ("bmips: add new target")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-23 12:57:28 +01:00
Álvaro Fernández Rojas
f0d5eb149e bmips: remove unneeded downstream serial patch
Disabling CONFIG_SERIAL_8250 makes the upstream serial driver work OOB.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-23 12:35:52 +01:00
Daniel González Cabanelas
50cb3a750f bcm63xx: pinctrl: fix BCM6348 groups
The current driver has some troubles:
 - Some groupings are wrong.
 - The pinctrl group0 owns pins never used (at least in Openwrt) for any
   pinmux. The driver hijacks all the pins on the group avoiding any other
   use, spite they're free. I.e. for buttons, causing this kernel error:
   [  4.735928] gpio-keys-polled keys: unable to claim gpio 479, err=-22
   [  4.742642] gpio-keys-polled: probe of keys failed with error -22
 - Minor errors about groupings on the documentation
 - Missing "diag" grouping in dtsi
 - Wrong groupings in dtsi

Fix it by setting the correct groups.
And relax the pin capturing, letting the gpios belonging to any group to
be used for other purposes like buttons. This was the behavior with stock
firmwares and old OpenWrt versions which never caused any trouble.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-02-23 11:01:20 +01:00
Álvaro Fernández Rojas
09bbf55817 bmips: bcm6358: fix EHCI/OHCI kernel panics
ARCH_HAS_SYNC_DMA_FOR_CPU_ALL is causing kernel panics when EHCI or OHCI are
enabled.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-23 10:52:06 +01:00
Adrian Schmutzler
e4d1163de4 imx6: remove redundant IMAGE_NAME
IMAGE_NAME is set twice for ventana, and the second value
actually matches the default in image.mk. Remove both.

Fixes: ded905ce43 ("imx6: extend cubox support to hummingboard,
add support for building full images")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 00:26:40 +01:00
Paul Spooren
6ab33103af treewide: remove redundant KERNEL_PREFIX definitions
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 00:26:40 +01:00
Adrian Schmutzler
020e51facf bmips: split base-files into subtargets
Like done for several targets already, splitting base-files into
subtarget will provide smaller images due to more specific
distribution of files per subtarget and allow to use default cases
more effectively.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-23 00:26:40 +01:00
Álvaro Fernández Rojas
117b833d61 bmips: add JFFS2 unaligned access patch
This patch is also needed on bmips if SMP is enabled.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-22 21:37:56 +01:00
Álvaro Fernández Rojas
626add3394 bmips: bcm6368: fix bcm2835-rng
IPSEC needs a reset before using its HW RNG.
Otherwise, the numbers generated won't be random at all.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-22 21:37:56 +01:00
Shiji Yang
567a88e4b9 ramips: fix Phicomm PSG1218A switch port labels
The lan port sequence was reversed compared to the labels.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:49:57 +01:00
Adrian Schmutzler
d4520d75a1 ramips: move aliases to the top in SoC DTSI files
The aliases node is expected as one of the first entries, and
having it there matches alphabetic sorting as well.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:49:57 +01:00
Adrian Schmutzler
86a4d78022 ramips: drop redundant definitions of serial0 in aliases
These were redefines of the same value already set in the SoC dtsi
files.

Reported-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:49:57 +01:00
Álvaro Fernández Rojas
029093a302 bmips: add new target
This target has full device tree support, thus reducing the number of
patches needed for bcm63xx, in which there's a patch for every board.

The intention is to start with a minimal amount of downstream patches and
start upstreaming all of them.

Current status:
 - Enabling EHCI/OHCI on BCM6358 causes a kernel panic.
 - BCM63268 lacks Timer Clocks/Reset support.
 - No PCI/PCIe drivers.
 - No ethernet drivers.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:29:44 +01:00
Álvaro Fernández Rojas
c27532742d bcm63xx: limit name metadata to model name
Since there are only 16 characters available, on most cases the vendor name
will fit in the metadata, but the model name won't fit.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-22 18:29:44 +01:00
Álvaro Fernández Rojas
7405ff5d4b kernel: mtdsplit: add support for BCM63XX CFE firmware
Broadcom CFE bootloader relies on a tag for identifying the current firmware,
such as version, image start address, kernel address and size, rootfs size,
board id, signatures, etc.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-22 18:09:03 +01:00
Shiji Yang
55263ffedb ramips: correct/add Phicomm K2x WAN/label MAC address
Phicomm K2G:
add missing label_mac

Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 17:32:35 +01:00
Álvaro Fernández Rojas
36e35b8d81 bcm63xx: bcm63268: fix GPIO interrupts
pinctrl should rely on external interrupt controller for GPIO interrupts.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-22 09:04:04 +01:00
David Bauer
f79f496ed6 generic: add missing symbol
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-22 00:57:34 +01:00
David Bauer
2a26cb51fe ath79: enable Regulator support for target
Regulator support was enabled on all subtargets except for ath79-nand.
With Kernel 5.10, AT803x requires Regulator support, thus enabling on
the complete target, as ath79-nand requires AT803x.

While this is only required on Kernel 5.10, enable it also on 5.4. We
have no major size-constraint, so enabling it on 5.4 allows us to clean
up the occurences in the subtarget configuration.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-22 00:57:25 +01:00
David Bauer
08826595fc mpc85xx: add testing kernel for p1020
CONFIG_REGULATOR is required for the p1020 subtarget, as the AT803X
driver depends on it.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-22 00:56:16 +01:00
David Bauer
81b44a3626 ath79: use ioremap kernel version independent
As mangix pointed out on IRC, ioremap and ioremap_nocache are
functionally equivalent on kenrel 5.4 and 5.10.

Therefore we can use ioremap regardless of the kernel the driver
gets compiled for.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-22 00:55:42 +01:00
Aleksander Jan Bajkowski
777e67301a kernel: sort config
This was done by executing this script:

find . -name "config-*"  > ../configs.txt
for config in $(cat ../configs.txt); do
	./scripts/kconfig.pl '+' $config /dev/null > $config-new
	mv $config-new $config
done
rm ../configs.txt

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2021-02-21 23:52:26 +01:00
Álvaro Fernández Rojas
9dc84018ee bcm27xx: remove urngd package
Now that khwrngd is working on all subtargets we can remove urgnd.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-20 19:55:14 +01:00
Álvaro Fernández Rojas
670526efa3 bcm27xx: enable bcm2711 HW RNG
Also add a patch setting its quality, which should make it usable by khwrngd.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-20 19:53:50 +01:00
Álvaro Fernández Rojas
7747b3fa36 generic: add bcm2835-rng quality patch
This patch allows devices without a high resolution timer to boot up faster.
It should speed up boots for bcm2708 and bcm63xx.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-20 18:59:25 +01:00
Andreas Eberlein
a3e6521c1a x86: add led driver for PC Engines APU1
This driver adds the LED support for the PC Engines APU1.
This integrates the Linux kernel driver and includes a patch to support
 newer firmware versions. Also the default LED configuration is updated
 to use the correct devices.

Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
2021-02-20 00:29:18 -10:00
David Bauer
bb817bb4b8 sdk: expose binary strip settings
Expose the SDK options for binary stripping to the menuconfig. This
way, packages can easily be built with debug symbols using the SDK.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:29:36 +01:00
Stijn Segers
af1b6799c6 ramips: overwrite reset gpio properties in EX6150 DTS
The Netgear EX6150 can, just like the D-Link DIR-860L rev B1, fail to
initialise both radios in some cases. Add the reset GPIOs explicitly
so the PCI-E devices get re-initialised properly. See also FS #3632.

Error shows up in dmesg as follows:

  [    1.560764] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[removed period from commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:27:00 +01:00
David Bauer
d6b785d477 ath79: add kernel 5.10 support
This adds Kernel 5.10 support for the generic, nand and tiny subtargets.

The following patch is not contained, as it needs to be reworked:
platform/920-mikrotik-rb4xx.patch

Tested-on:
 - Siemens WS-AP3610
 - Enterasys WS-AP3710
 - Aerohive HiveAP 121
 - TP-Link TL-WA901 v2
 - TP-Link TL-WR741 v1

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:26:33 +01:00
David Bauer
fb64e2c30f ath79: ar934x-nand: add kernel 5.10 compatibility
Adapt the driver to make it work with the NAND subsystem changes between
kernel 5.4 and 5.10.

Tested-on: Aerohive HiveAP121

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:26:22 +01:00
David Bauer
da55758cc5 ath79: specify device-type for PCI controllers
Specify the device_type property for PCI as well as PCIe controllers.
Otherwise, the PCI range parser will not be selected when using kernel
5.10.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:26:14 +01:00
David Bauer
3832403771 ath79: ag71xx: make kernel 5.10 compatible
Add the necessary kernel version ifdef switches in order to support the
kernel version 5.10.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:26:04 +01:00
David Bauer
5bd6d9377d mpc85xx-p1010: add Kernel 5.10 support
Tested on: Sophos RED 15W

The TP-Link WL-WDR4900 needs to be disabled when 5.10 becomes the
default kernel.

When building with all kmods enabled, the resulting kernel image
exceeds the maximum size the bootloader reads from the flash.

For more information, see GitHub issue #1773

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:26:00 +01:00
David Bauer
422b3e1993 rockchip: add Kernel 5.10 support
Remove all upstreamed patches and add the kernel configuration for
version 5.10.

The Rock Pi 4 was split in multiple versions. Add a DTS with the old
name in order to keep compatibility while having kernel 5.4 and 5.10 in
parallel. Switch to the Rock Pi 4A DTS once Kernel 5.4 support is
removed.

Tested-on: Nanoi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-20 01:26:00 +01:00
Sungbo Eo
2ff9686040 kirkwood: rename files-5.4 to files
Move local DTS files from "files-5.4" to "files" directory so kernel 5.10
can use it.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-19 15:56:04 +01:00
Yangbo Lu
a31842e7fd layerscape: add new devices in README and clean up
Support new devices LS1046AFRWY and LX2160ARDB in README.
Clean up README, and add missing LS1021ATWR deploy guide.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[adjust set of devices added, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:30:10 +01:00
Yangbo Lu
80dcd14abe layerscape: add LX2160ARDB (Rev2.0 silicon) board support
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.

- Enables network intelligence with the next generation Datapath (DPPA2)
  which provides differentiated offload and a rich set of IO, including
  10GE, 25GE, 40GE, and PCIe Gen4

- Delivers unprecedented efficiency and new virtualized networks

- Supports designs in 5G packet processing, network function
  virtualization, storage controller, white box switching, network
  interface cards, and mobile edge computing

- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
  and 8-core LX2080A)

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:29:46 +01:00
Yangbo Lu
2c2d77bd3b layerscape: add FRWY-LS1046A board support
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.

The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:27:15 +01:00
Adrian Schmutzler
a9075d42d7 layerscape: move rework-sdcard-images out of fsl-sdboot
Upcoming devices will not need the migration setup, so let's move
it out of the common definition.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 15:23:52 +01:00
Seo Suchan
ca6954e2dc ramips: use lzma-loader for Wevo devices
As kernel size increased it start to fail to load squishfs image,
using lzma-loader fixed it.
wevo_11acnas is almost same device as w2914ns-v2 except ram size,
so I expect same thing would've happen in that device too.

Signed-off-by: Seo Suchan <abnoeh@mail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-02-19 14:09:50 +01:00
Sander Vanheule
1e75909a35 ramips: mt7621: add TP-Link EAP235-Wall support
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.

When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.

The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.

Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
  * Back side: ETH0, PoE PD port
  * Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)

Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).

Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
    eth     a4:2b:b0:...:88
    ra0     a4:2b:b0:...:88
    rai0    a4:2b:b0:...:89

Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface

Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
  pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
  bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
    # tftpboot 84000000 openwrt-initramfs.bin
    # bootm

Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
  $ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
      -z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin

This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.

Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
  This was an issue with the ddc75ff704 version of mt76, but appears to
  have improved/disappeared with bc3963764d.
  Error notice example:
  [ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout

Hardware was kindly provided for porting by Stijn Segers.

Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-02-19 14:00:08 +01:00
Stijn Segers
0265cba40a ramips: remove factory image for TP-Link Archer C20 v1
Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one
tries to flash an OpenWrt factory image through the TP-Link web UI.
The wiki page contains an explicit warning about this [1].

Disable the factory image altogether since it serves no purpose.

[1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-02-19 13:56:27 +01:00
Adrian Schmutzler
63e1ce3e09 ath79: fix position of SPDX license identifier
Strictly, the identifier needs to be in the line directly after the
shebang.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 13:53:22 +01:00
Adrian Schmutzler
45e8d9b480 mediatek: fix SPDX license identifier on local DTS files
The SPDX license identifier must be in the first line of a file,
unless there is a shebang (then it's the second line).

Fix this for the local files, do not care about the upstream patches.

While at it, update the identifiers where necessary.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-19 13:47:45 +01:00
Álvaro Fernández Rojas
31a06f8fcc bcm63xx: update ethernet kernel panics fix
Use new patch from Sieng Piaw Liew.

Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-19 12:28:19 +01:00
Daniel Golle
c7293bcfcc
mediatek: move mt7623a-unielec-u7623*.dts* out of patch
Instead of adding those device tree sources using a patch, simply move
them to the newly created dts folder.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-19 10:00:46 +00:00
Álvaro Fernández Rojas
5bab472a11 bcm27xx: add diag LEDs
We can now use the power LED for diag in more devices thanks to the latest
patches from the RPi foundation.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-19 08:09:11 +01:00
Álvaro Fernández Rojas
0aaa2cce1c bcm27xx: bcm2708: add missing RPi B DTS file
RPI 1B DTS has been splitted into 2 files:
 - bcm2708-rpi-b.dts: Newest (rev2) RPI 1B
 - bcm2708-rpi-b-rev1.dts: Old (rev1) RPI 1B

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-19 08:09:11 +01:00
Daniel Golle
e3b8849088
mediatek: more clean solution for out-of-tree DTS
Use approach suggested by Adrian Schmutzler instead of introducing
another device variable.
Also revert the unnecessary white-space changes accidentally introduced
by the previous commit.

Fixed: c067b1e79b ("mediatek: move out-of-tree DTS files to dedicated dts folder")
Suggested-by: Adrian Schmutzler <mail@adrianschmutzler.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-19 01:25:49 +00:00
Daniel Golle
c067b1e79b
mediatek: move out-of-tree DTS files to dedicated dts folder
Use dedicated dts folder like on ramips to store device tree source
files for boards not already supported in vanilla Linux.
Doing so instead of having them in files-* has several advantages:
 * we don't need to duplicate them for several kernel versions
 * changes to a device tree don't trigger a complete kernel rebuild
 * the files are more obvious to find

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-19 00:05:53 +00:00
Álvaro Fernández Rojas
8ad61118fd bcm27xx: add support for RPI CM4 and RPI 400
Support added to bcm2709 (32 bits) and bcm2711 (64 bits).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-18 23:43:18 +01:00
Álvaro Fernández Rojas
f07e572f64 bcm27xx: import latest patches from the RPi foundation
bcm2708: boot tested on RPi B+ v1.2
bcm2709: boot tested on RPi 3B v1.2 and RPi 4B v1.1 4G
bcm2710: boot tested on RPi 3B v1.2
bcm2711: boot tested on RPi 4B v1.1 4G

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-18 23:42:32 +01:00
John Audia
5d3a6fd970 kernel: bump 5.4 to 5.4.99
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.

Build system: x86_64
Build-tested: bcm27xx/bcm2711

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-18 20:04:50 +01:00
Mathias Kresin
ba07cc0cbb lantiq: fritz7320: enable USB power supply
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.

Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.

Fixes FS#3624

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-02-18 08:43:08 +01:00
David Bauer
5408399fcb generic: don't lock when recursively deleting partitions
When recursively deleting partitions, don't acquire the masters
partition lock twice. Otherwise the process endy up in a deadlocked
state.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-18 01:16:40 +01:00
David Bauer
0621b23efb generic: add various kernel 5.10 config symbols
These symbols were unset when configuring for ath79.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-18 01:16:20 +01:00
David Bauer
634c13c186 mediatek: add support for Ubiquiti UniFi 6 LR
Hardware
--------

MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch

UART
----

CPU UART0 at the pinout next to the Holtek MCU.

Pinout (first pin next to SoC / MCU)

0 3V3
1 RX
2 TX
3 GND

Settings are 115200 8N1.

Opening the case
----------------

Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.

Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.

Installation
------------

1. Connect to the booted device at 192.168.1.20 using username/password
   "ubnt".

2. Transfer the OpenWrt sysupgrade image to the device using SCP.

3. Check the mtd partition number for bs / kernel0 / kernel1

   $ cat /proc/mtd

4. Set the bootselect flag to boot from kernel0

   $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6

5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1

   $ dd if=openwrt.bin of=/dev/mtdblock8
   $ dd if=openwrt.bin of=/dev/mtdblock9

6. Reboot the device. It should boot into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-18 01:15:45 +01:00
David Bauer
c9137e2ddf mediatek: add Ubiquiti LED driver
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.

This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-18 01:15:33 +01:00
Álvaro Fernández Rojas
f323dec4f8 bcm63xx: add kernel 5.10 support
Runtime-tested on Comtrend AR-5387un.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-17 20:40:16 +01:00
Daniel Golle
5bb9954826 kernel: update kernel 5.10 to 5.10.16
Compile and runtime-tested on mediatek/mt7622

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-17 13:48:43 +00:00
Adrian Schmutzler
0e43f62f21 kernel: 5.10: refresh patches
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-16 23:48:23 +01:00
Adrian Schmutzler
0c7340f0a2 kernel: 5.10: add missing partitions doc syntax commit
This patch has been added to 5.4, but not been copied to 5.10:
7495acb555 ("kernel: backport mtd commit converting partitions doc syntax")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-16 23:48:23 +01:00
Adrian Schmutzler
1013bf433b kernel: hack-5.10: make UDP tunneling user-selectable
This applies another patch from 5.4 to 5.10 as well:
de09355f74 ("kernel/hack-5.4: make UDP tunneling user-selectable")

UDP tunneling support isn't user-selectable, but it's required by WireGuard
which is, for the time being, an out-of-tree module. We currently work around
this issue by selecting an unrelated module which depends on UDP tunnelling
(VXLAN). This is inconvenient, as it implies this unrelated module needs to be
built-in when doing a monolithic build.

Fix this inconvenience by making UDP tunneling user-selectable in the kernel
configuration.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-16 23:48:23 +01:00
Adrian Schmutzler
487b7ae5eb kernel: 5.4: fix .patch file extension
File extension was truncated for
pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-16 23:48:23 +01:00
Adrian Schmutzler
99f2b464b4 kernel: 5.10: fix busy wait loop in mediatek PPE code
Reapply changes added to 5.4 but not copied to 5.10:
3da4acaa7b ("kernel: fix busy wait loop in mediatek PPE code")

The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.

time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-16 23:46:30 +01:00
Adrian Schmutzler
0e407dfe8b generic: ar8216: update version switch for of_get_phy_mode fix
Kernel has changed the of_get_phy_mode API in commit 0c65b2b90d13
("net: of_get_phy_mode: Change API to solve int/unit warnings").

This is already included in kernel 5.5, so fix the version switch
(though this will not actually matter for the versions we support).

Similar driver adjustments to account for the API change will
probably be necessary to various other local drivers.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-16 23:42:43 +01:00
David Bauer
a24df045db generic: ar8216: fix kernel 5.10 compile error
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-16 22:53:10 +01:00
Felix Fietkau
b10d604459 kernel: add linux 5.10 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-02-16 20:06:51 +01:00
Rafał Miłecki
ad8b759fd1 bcm4908: add bcm_sf2 fixes for the 5th GPHY
This allows using the last integrated PHY (and so e.g. WAN port on the
ASUS GT-AC5300).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-16 07:10:33 +01:00
Rafał Miłecki
f0933303d6 bcm4908: fix GPIOs support by limiting them to 64
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 22:18:50 +01:00
Rafał Miłecki
da92e9825a bcm4908: use DTS patches sent upstream
There are 2 new patches:
1. Netgear R8000P switch ports
2. Netgear R8000P LEDs

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 22:18:45 +01:00
Rafał Miłecki
95359dac82 bcm4908: add USB packages to the DEFAULT_PACKAGES
All known 41 BCM4908 devices have USB ports so it makes sense to include
those packages by default.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 16:54:28 +01:00
Rafał Miłecki
26052fb355 bcm4908: fix backport of PMB driver
Missing Makefile change was preventing kernel from actually compiling
the driver.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 16:54:25 +01:00
Rafał Miłecki
09fbc79bf6 kernel: drop ofpart patch dropped from upstream mtd tree
It stopped ofpart_parser_init() from being called

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 15:06:40 +01:00
Rafał Miłecki
ac7d45b5e7 kernel: backport "ofpart" mtd parser upstream quirks support
This adds quirks support to the "ofpart" parser. It's required to
support fixed partitions that require some extra logic.

Right now only BCM4908 binding is supported (BCM4908 requires detecting
currently used "firmware" partition).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-15 12:02:33 +01:00
Ilya Lipnitskiy
3da4acaa7b kernel: fix busy wait loop in mediatek PPE code
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.

time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-02-15 08:13:16 +01:00
Kurt Roeckx
539966554d ramips: mark toggle input on EX6150 as a switch
The Netgear EX6150 has an Access Point/Extender switch. Set it as
an EV_SW. Otherwise when it's set to Access Point, it will trigger
failsafe mode during boot.

Fixes: FS#3590
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
2021-02-15 00:00:38 +01:00
Petr Štetiar
0fde111702 Revert "imx6: bootscript-apalis: make it working on v2021.01 release"
This reverts commit 4968fc8fb1 as the bump
to v2021.01 needs swig on the host for pylibfdt which is needed by dtoc
tool to generate .h/.c files from DTBs in SPL for mx6cuboxi_config.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-02-14 23:28:07 +01:00
Adrian Schmutzler
4894a3ff28 target: fix copying of licenses for SDK/toolchain
The SDK and target/toolchain copy the license file into their
directories. During the rename/move from LICENSE to a LICENSES
folder, this has not been updated.

Update it now, and include the new COPYING file.

While at it, improve formatting/indent.

Fixes: 882e301461 ("LICENSES: include all used licenses in
LICENSES directory")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-14 21:56:29 +01:00
Paul Fertser
25d6af98d0 ath79: fix factory image generation for Netgear and Zyxel boards
The factory images need to embed specific IDs to pass verification with
the OEM firmware (including TFTP recovery), so they need to be
per-device variables.

Fixes: ab1584a797 ("ath79: netgear: trim down uImage customisations")
Fixes: 459c8c9ef8 ("ath79: add support for ZyXEL NBG6616")
Reported-by: Marcin Juszkiewicz <marcin-openwrt@juszkiewicz.com.pl>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[minor commit message adjustments, sort DEVICE_VARS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-14 19:21:38 +01:00
Tomasz Maciej Nowak
1caa81e505 mvebu: espressobin: drop COMPHY removement patch
There are proper workarounds merged to 5.4 stable tree for ESPRESSObin
boards with older bootloader:
4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720")
40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2021-02-14 09:34:57 +01:00
Sander Vanheule
69551a2442 ramips: manage low reset lines
The bootloader of a number of recent TP-Link devices does not properly
initialise the MT7621's internal switch when booting from flash. To
enable the mt7530 driver to clear the reset on the switch, the ramips
reset controller must be allowed to toggle these.

Backport upstream commit 3f9ef7785a9c from mips-next to allow control of
the "mcm" reset line.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2021-02-14 09:33:42 +01:00
Petr Štetiar
4968fc8fb1 imx6: bootscript-apalis: make it working on v2021.01 release
Upstream in commit 8b9c0cb46471 ("apalis_imx6: boot env configuration
updates") removed emmc legacy wrappers, but so far didn't included any
replacements. Fix it by simply defining the missing variables and UUID
gathering directly into the boot script.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-02-14 09:31:30 +01:00
Adrian Schmutzler
a45953c2f2 bcm4908: refresh patches
Our patch refresh tool creates quite a big diff for these patches,
as it does not use rename syntax.

Push the refresh separately so it does not pollute the next kernel
bump. This is a purely cosmetic change.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-13 21:21:01 +01:00
Martin Kennedy
e2db870398 ath79: fix chip used for Meraki MR12 caldata_extract
The original setup fails to trigger ART calibration data
extraction for the AR9287. Instead, it would only have extracted
calibration data for an internal WMAC chip which is not present on
this board.

Fixes: 55d2db0e8c ("ath79: add support for Meraki MR12")

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-13 21:21:01 +01:00
Stijn Segers
ad5e29d38a ramips: remove factory image for TP-Link Archer C2 v1
Initial commit 8375623a06 ("ramips: add support for TP-Link Archer
C2") contains detailed installation instructions, which do not mention
a factory image. From what I can see, no support to install OpenWrt
through the vendor web interface has been added since. The factory
image is also conspicuously absent from the device page in the wiki.
Yet, it is available for download.

I bricked my Archer C2 loading the factory image through the web UI.
Serial showed this error during bootloop:

  Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover

This patch disables the undocumented factory image so users won't get
tricked into thinking easy web UI flashing actually works.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-02-13 21:21:01 +01:00
Rafał Miłecki
d8afae0be8 bcm4908: fix handling Ethernet frames of size 1506 - 1514
MTU needs to be explicitly set as default value is too low.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-12 16:30:14 +01:00
Rafał Miłecki
87efff6329 bcm4908: use upstream accepted Ethernet driver patches
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-12 16:30:14 +01:00
Michael Mohr
8cbd6f5117 realtek: add support for Netgear GS108T v3
The Netgear GS108T v3 is an 8 port gigabit switch with PoE-PD support
on port 1.  The two prior versions were built using eCos and are not
currently compatible with OpenWRT.

The GS108T v3 is quite similar to both the GS110TPP v1 and GS110TP v3,
all of which use the same firmware image from Netgear.  For this reason,
the device tree is identical aside from the model and compatible values.

All of the above feature a dual firmware layout, referred to as Image0
and Image1 in the Netgear firmware.

Hardware specification
----------------------

 * RTL8380M SoC, 1 MIPS 4KEc core @ 500MHz
 * 128MB DDR3-1600 DRAM (Winbond W631GG8MB-12)
 * 32MB 3v NOR SPI Flash (Macronix MX25L25635F or Winbond W25Q256JVFIQ)
 * RTL8231 GPIO extender to control the LEDs and the reset button
 * 8 x 10/100/1000BASE-T ports, internal PHY (RTL8218B)
 * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J1
 * Power is supplied via a 12V 1A barrel connector or 802.3af

UART pinout
-----------

J1 | [o]ooo
      ^ ||`------ GND
      | |`------- RX         [TX out of the serial adapter]
      | `-------- TX         [RX into the serial adapter]
      `---------- Vcc (3V3)  [the square pin]

The through holes are filled with PB-free solder which melts at 375C.
They can also be drilled using a 0.9mm bit.

Build configuration
-------------------

 * Target System: Realtek MIPS
 * Target Profile: Netgear GS108T v3
 * Target Images -> ramdisk -> Compression: lzma
 * Disable other target images

Boot initramfs image from U-Boot
--------------------------------

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Init network with `rtk network on` command
 3. Load image with `tftpboot 0x8f000000 openwrt-realtek-generic-netgear_gs108t-v3-initramfs-kernel.bin` command
 4. Boot the image with `bootm` command

The switch defaults to IP 192.168.1.1 and tries to fetch the image via
TFTP from 192.168.1.111.

Updating the installed firmware
-------------------------------

The OpenWRT ramdisk image can be flashed directly from the Netgear UI.
The Image0 slot should be used in order to enable sysupgrade.

As with similar switches, changing the active boot partition can be
accomplished in U-Boot as follows:

 1. Press the Escape key at the `Hit Esc key to stop autoboot` prompt
 2. Run `setsys bootpartition {0|1}` to select the boot partition
 3. Run `savesys` followed by `boota` to proceed with the boot process

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Michael Mohr
9fe90e4e5a realtek: refactor the Netgear GS110TPP v1 device tree
Move most of the GS110TPP v1 device tree into a dtsi so that it can be
shared with the GS108T v3.  Additionally:

  * Use macros to simplify the ethernet and switch definitions
  * Zero-pad the offsets and sizes in the partition map to 8 digits each

The spi-max-frequency value has been changed from 10MHz to 50MHz based
on an analysis of the relevant datasheets.  The current driver doesn't
use this property, as the clock speed is fixed. However, it's required
for this type of DT node, so that's why it's present here.

The firmware partition has been split in half, since this is how the
stock firmware uses it.  This can be used to easily revert to a stock
firmware if one is written to the second image area.

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Michael Mohr
9877393fd1 realtek: add and use netgear_nge for the GS110PP v1
The netgear_nge device will be shared between the GS108T v3 (to be added
in a later commit) and the GS110PP v1.  It also enables LZMA compression
for the ramdisk image.

Signed-off-by: Michael Mohr <akihana@gmail.com>
2021-02-12 08:52:41 +01:00
Adrian Schmutzler
6934d30cf8 ath79: fix USB power GPIO for TP-Link TL-WR810N v1
The TP-Link TL-WR810N v1 is known to cause soft-brick on ath79 and
work fine for ar71xx [1]. On closer inspection, the only apparent
difference is the GPIO used for the USB regulator, which deviates
between the two targets.

This applies the value from ar71xx to ath79.

Tested successfully by a forum user.

[1] https://forum.openwrt.org/t/tp-link-tl-wr810n-v1-ath79/48267

Fixes: cdbf2de777 ("ath79: Add support for TP-Link WR810N")
Fixes: FS#3522

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-11 23:58:32 +01:00
INAGAKI Hiroshi
08768b44d9 ramips: add support for ELECOM WRC-1167FS
ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7628AN.

Specification:

- SoC		: MediaTek MT7628AN
- RAM		: DDR2 64 MiB (NT5TU32M16FG-AC)
- Flash		: SPI-NOR 16 MiB (W25Q128JVSIQ)
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7628AN (SoC)
  - 5 GHz	: MediaTek MT7612E
- Ethernet	: 10/100 Mbps x2
  - Switch	: MT7628AN (SoC)
- LEDs/Keys	: 6x, 3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J1: 3.3V, GND, TX, RX from "J1" marking
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WRC-1167FS normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button to
   perform firmware update
4. Wait ~120 seconds to complete flashing

Notes:

- Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware

- Additional padding in factory image is required to avoid incomplete
  flashing on stock firmware

MAC addresses:

- LAN	: BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28   (hex))
- WAN	: BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22   (hex))
- 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac    (text) / Factory, 0x4    (hex))
- 5GHz	: BC:5C:4C:xx:xx:6B (Config, rmac2   (text) / Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2021-02-11 16:37:53 +01:00
John Audia
e95b1b23f1 kernel: bump 5.4 to 5.4.97
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Manually rebased:
 bcm27xx
  950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
 bcm53xx
  180-usb-xhci-add-support-for-performing-fake-doorbell.patch
 layerscape
  302-dts-0008-arm64-dts-ls1046a-accumulated-change-to-ls1046a-boar.patch
  820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
  820-usb-0018-MLK-18794-1-usb-host-xhci-add-.bus_suspend-override.patch

Build system: x86_64
Build-tested: bcm27xx/bcm2711, ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions/everything functional.

Signed-off-by: John Audia <graysky@archlinux.us>
[remove quilt comment, fix/adjust 820-usb-* layerscape patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-11 16:08:28 +01:00
Adrian Schmutzler
3cc08b5702 at91: use SPDX license identifiers on DTS files
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:23 +01:00
Adrian Schmutzler
7157c77c6d target: use SPDX license identifiers on scripts
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:23 +01:00
Adrian Schmutzler
598b29585e target: use SPDX license identifiers on Makefiles
Use SPDX license tags to allow machines to check licenses.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-10 15:47:18 +01:00
Rafał Miłecki
c382fe857d bcm4908: update Ethernet driver
Use the latest version sent upsteram.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-10 11:28:04 +01:00
Andrew Pikler
cd2b661453 ramips: add support for Cudy WR1300
Specifications:
 - SoC: MediaTek MT7621AT
 - RAM: 128 MB (DDR3)
 - Flash: 16 MB (SPI NOR)
 - WiFi: MediaTek MT7603E, MediaTek MT7612E
 - Switch: 1 WAN, 4 LAN (Gigabit)
 - Ports: 1 USB 3.0
 - Buttons: Reset, WPS
 - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
 - Power: DC 12V 1A tip positive

UART Serial:
  115200 baud
  Located on unpopulated 4 pin header near J4:

  J4
  [o] Rx
  [o] Tx
  [o] GND
  [ ] Vcc - Do not connect

Installation:

Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.

Recovery:
 - Loads only signed manufacture firmware due to bootloader RSA verification
 - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
 - connect to any lan ethernet port
 - power on the device while holding the reset button
 - wait at least 8 seconds before releasing reset button for image to
   download
 - See http://www.cudytech.com/newsinfo/547425.html

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:f0      label
WAN   *:f1      label + 1
2g    *:f0      label
5g    *:f2      label + 2

The label MAC address is found in bdinfo 0xde00.

Signed-off-by: Andrew Pikler <andrew.pikler@gmail.com>
2021-02-09 13:58:18 +01:00
Sebastian Schaper
dc4745da7a ath79: add support for D-Link DAP-3662 A1
Specifications:
 * QCA9557, 16 MiB Flash, 128 MiB RAM, 802.11n 2T2R
 * QCA9882, 802.11ac 2T2R
 * 2x Gigabit LAN (1x 802.11af PoE)
 * IP68 pole-mountable outdoor case

Installation:
 * Factory Web UI is at 192.168.0.50
   login with 'admin' and blank password, flash factory.bin
 * Recovery Web UI is at 192.168.0.50
   connect network cable, hold reset button during power-on and keep it
   pressed until uploading has started (only required when checksum is ok,
   e.g. for reverting back to oem firmware), flash factory.bin

After flashing factory.bin, additional free space can be reclaimed by
flashing sysupgrade.bin, since the factory image requires some padding
to be accepted for upgrading via OEM Web UI.

Both ethernet ports are set to LAN by default, matching the labelling on
the case. However, since both GMAC Interfaces eth0 and eth1 are connected
to the switch (QCA8337), the user may create an additional 'wan' interface
as desired and override the vlan id settings to map br-lan / wan to either
the PoE or non-PoE port, depending on the individual scenario of use.

So, the LAN and WAN ports would then be connected to different GMACs, e.g.

config interface 'lan'
	option ifname 'eth0.1'
	...

config interface 'wan'
	option ifname 'eth1.2'
	...

config switch_vlan
        option device 'switch0'
        option vlan '1'
        option ports '1 0t'

config switch_vlan
        option device 'switch0'
        option vlan '2'
        option ports '2 6t'

Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
[add configuration example]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-09 13:10:33 +01:00
Chukun Pan
82032f3509 ramips: add support for JCG Y2
JCG Y2 is an AC1300M router

Hardware specs:
  SoC: MediaTek MT7621AT
  Flash: Winbond W25Q128JVSQ 16MiB
  RAM: Nanya NT5CB128M16 256MiB
  WLAN: 2.4/5 GHz 2T2R (1x MediaTek MT7615)
  Ethernet: 10/100/1000 Mbps x5
  LED: POWER, INTERNET, 2.4G, 5G
  Button: Reset
  Power: DC 12V,1A

Flash instructions:
  Upload factory.bin in stock firmware's upgrade page.

MAC addresses map:
  0x0004  *:c8  wlan2g/wlan5g/label
  0xe000  *:c7  lan
  0xe006  *:c6  wan

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2021-02-09 13:10:33 +01:00
Michael Pratt
f5f01bcacd ath79: use internal switch for EAP300 v2
Have the port use GMAC1 with internal switch
which fixes the issue of the ethernet LED not functioning
The LED is triggered by the internal switch, not a GPIO.

The GPIO for the ethernet LED was added in ath79
as it was defined in the ar71xx target
but it was not functioning in ath79 for a previously unknown reason.

It is unknown why that GPIO was defined as an LED in ar71xx.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
[drop unrelated changes: model property and SPI max frequency]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-08 16:34:18 +01:00
Michael Pratt
88079bd616 ath79: make all eth ports LAN for Engenius APs
for:
 - ENH202 v1
 - ENS202EXT v1
 - EnstationAC v1
 - EWS511AP

For EWS511AP, have default behavior as static ip
to match the behavior of all other APs in ath79

These boards are sold as
Client Bridge or Point to Point or Access Point
so there is probably no benefit to have WAN by default
for one of the ports, to prevent user confusion.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-02-08 16:34:18 +01:00
John Audia
f3b827a965 kernel: bump 5.4 to 5.4.96
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
Run-tested [*]: ramips/mt7621 (R6800, DIR-878 A1, EAP235-Wall)

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-02-08 16:34:18 +01:00
Rafał Miłecki
f06c3031a7 bcm4908: add board.d network setup
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-08 12:05:56 +01:00
Rafał Miłecki
81240a9b89 bcm4908: add Ethernet driver
This commit picks up pending netdev patches.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-08 11:49:21 +01:00
Szabolcs Hubai
1e9afcca56 ramips: disable default build for HooToo HT-TM02
While the latest version of 19.07 release is usable,
the current master is unbootable on the device in a normal way.

"Normal way" installations includes:
- sysupgrade (e.g. from 19.07)
- RESET button recovery with Ron Curry's (Wingspinner) UBoot image
  (10.10.10.3 + "Kernal.bin")
- RESET button recovery with original U-Boot
  (10.10.10.254 + "kernel")

One could flash and boot the latest master sysupgrade image successfully
with serial access to the device. But a sysupgrade from this state still
breaks the U-Boot and soft-bricks the device.

Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
2021-02-07 22:06:57 +01:00
Adrian Schmutzler
1c0e13db43 ramips: mt7621: use preferred logic in lib/upgrade/iodata.sh
shellcheck recommends || and && over "-a" and "-o" because the
latter are not well defined.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
INAGAKI Hiroshi
88fbddb49d ramips: add support for I-O DATA WN-DX1200GR
I-O DATA WN-DX1200GR is a 2.4/5 GHz band 11ac (WiFi-5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: raw NAND 128 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: MediaTek MT7603E
  - 5 GHz	: MediaTek MT7613BE
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/keys	: 2x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J5: 3.3V, TX, RX, NC, GND from triangle-mark
  - 57600n8
- Power		: 12 VDC, 1 A

Flash instruction using initramfs image:

1. Boot WN-DX1200GR normally
2. Access to "http://192.168.0.1/" and open firmware update page
   ("ファームウェア")
3. Select the OpenWrt initramfs image and click update ("更新") button
   to perform firmware update
4. On the initramfs image, perform sysupgrade with the
   squashfs-sysupgrade image
5. Wait ~120 seconds to complete flashing

Notes:

- currently, mt7615e driver in mt76 doesn't fully support MT7613
  (MT7663) wifi chip
  - the eeprom data in flash is not used by mt7615e driver and the
    driver reports the tx-power up to 3dBm
  - the correct MAC address for MT7613BE in eeprom data cannot be
    assigned to the phy

- last 0x80000 (512 KiB) in NAND flash is not used on stock firmware

- stock firmware requires "customized uImage header" (called as "combo
  image") by MSTC (MitraStar Technology Corp.), but U-Boot doesn't

  - uImage magic ( 0x0 - 0x3 ) : 0x434F4D43 ("COMC")
  - header crc32 ( 0x4 - 0x7 ) : with "data length" and "data crc32"
  - image name   (0x20 - 0x37) : model ID and firmware versions
  - data length  (0x38 - 0x3b) : kernel + rootfs
  - data crc32   (0x3c - 0x3f) : kernel + rootfs

MAC addresses:

LAN:	50:41:B9:xx:xx:08 (Ubootenv, ethaddr (text) / Factory, 0x1E000 (hex))
WAN:	50:41:B9:xx:xx:0A (Factory,  0x1E006 (hex))
2.4GHz:	50:41:B9:xx:xx:08 (Factory,  0x4     (hex))
5GHz:	50:41:B9:xx:xx:09 (Factory,  0x8004  (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add check whether dflag_offset is set]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-07 21:58:51 +01:00
Daniel González Cabanelas
07f4e3b5b2 bcm63xx: kernel: reenable the TRNG
The hardware random number generator driver for bcm63xx was merged with
the one used by the Raspberry Pi. Now this driver is lost.

Reenable the HW_RANDOM kernel config with the new driver.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[refresh kernel config]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-07 19:06:52 +01:00
Pawel Dembicki
17fa01bb79 mpc85xx: refresh kernel config
Simple "make kernel_oldconfig" was done.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-02-06 17:13:33 +01:00
Thomas Beckler
450ec48d61 kirkwood: use 3 temperature sensors for Zyxel NSA310B
Instead of taking the input of one temperature sensor (temp1), the
script takes into account three temperature sensors to control the
PWM of the cooling fan.

temp1 -> placed on main board
temp2 -> placed on main board
temp3 -> placed on or close to chipset

All three temperatures give valid input for the PWM of the fan on
NSA310 and are actually changing.

Tested on two NSA310.

Signed-off-by: Thomas Beckler <thomas.beckler@hotmail.com>
Reviewed-by: Alberto Bursi <bobafetthotmail@gmail.com>
[commit title/message facelift, code cleanup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 22:21:08 +01:00
Adrian Schmutzler
8a79161a82 ath79: wrap ucidef_add_switch in 02_network
Wrap line to be consistent with all other definitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 21:57:19 +01:00
Yanase Yuki
d468ff97b7 build: move elx-header into image-commands.mk
ELECOM WAB-I1750-PS will need this in ath79, so move it to common
Makefile.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2021-02-05 21:57:19 +01:00
Sungbo Eo
321035420c kirkwood: refresh kernel config
Refresh config with make kernel_oldconfig.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-05 19:05:20 +01:00
Aleksander Jan Bajkowski
c9619fe6a5 lantiq: change phy-mode to mii for FRITZ!Box 7412
FRITZ!Box 7412 loads the firmware for fast ethernet PHY and mii is
more accurate in this case.
Gmii is used by Gigabit ethernet PHYs.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Reviewed-by: Mathias Kresin <dev@kresin.me>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:56:19 +01:00
Adrian Schmutzler
04a0e5c082 ipq806x: replace full-text BSC license by SPDX identifier
This replaces a full-text BSD clause by the corresponding SPDX
identifier.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:28:30 +01:00
Adrian Schmutzler
3f4d1dad00 ramips: replace full-text licenses by SPDX identifier
This replaces several full-text and abbreviated licenses found in
DTS files by the corresponding SPDX identifiers.

This should make it easier to identify the license both by humans
and machines.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 18:18:00 +01:00
David Bentham
4a18039785 ramips: add support for UniElec U7621-01
UniElec U7621-01 is a router platform board, the smaller model of
the U7621-06.
The device has the following specifications:

- MT7621AT (880 MHz)
- 256 of RAM (DDR3)
- 16 MB of FLASH (SPI NOR)
- 5x 1 Gbps Ethernet (MT7621 built-in switch)
- 1x 2.4Ghz MT7603E
- 1x 5Ghz MT7612
- 1x miniPCIe slots (PCIe bus only)
- 1x miniSIM slot
- 1x USB 2.0 (uses the usb 3.0 driver)
- 8x LEDs (1x GPIO-controlled)
- 1x reset button
- 1x UART header (4-pins)
- 1x GPIO header (30-pins)
- 1x DC jack for main power (12 V)

The following has been tested and is working:

- Ethernet switch
- 1x 2.4Ghz MT7603E (wifi)
- 1x 5Ghz MT7612 (wifi)
- miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
- miniSIM slot (works with normal size simcard)
- sysupgrade
- reset button

Installation:

This board has no locked down bootloader. The seller can be asked to
install openwrt v18.06, so upgrades are standard sysupgrade method.

Recovery:

This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.

LEDs list (left to right):

- ESW_P0_LED_0
- ESW_P1_LED_0
- ESW_P2_LED_0
- ESW_P3_LED_0
- ESW_P4_LED_0
- CTS2_N (GPIO10, configured as "status" LED)
- LED_WLAN# (connected with pin 44 in wifi1 slot)

Signed-off-by: David Bentham <db260179@gmail.com>
[add DEVICE_VARIANT, fix DEVICE_PACKAGES, remove &gpio]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 17:31:51 +01:00
Martin Kennedy
55d2db0e8c ath79: add support for Meraki MR12
Port device support for Meraki MR12 from the ar71xx target to ath79.

Specifications:

  - SoC: AR7242-AH1A CPU
  - RAM: 64MiB (NANYA NT5DS32M16DS-5T)
  - NOR Flash: 16MiB (MXIC MX25L12845EMI-10G)
  - Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY)
  - Ethernet: 1 x 100Mbit port (SoC MAC+PHY)
  - Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n)

Installation:

  1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins
  2. Open shell case
  3. Connect a USB->TTL cable to headers furthest from the RF shield
  4. Power on the router; connect to U-boot over 115200-baud connection
  5. Interrupt U-boot process to boot Openwrt by running:
       setenv bootcmd bootm 0xbf0a0000; saveenv;
       tftpboot 0c00000 <filename-of-initramfs-kernel>.bin;
       bootm 0c00000;
  6. Copy sysupgrade image to /tmp on MR12
  7. sysupgrade /tmp/<filename-of-sysupgrade>.bin

Notes:

  - kmod-owl-loader is still required to load the ART partition into the
    driver.

  - The manner of storing MAC addresses is updated from ar71xx; it is
    at 0x66 of the 'config' partition, where it was discovered that the
    OEM firmware stores it. This is set as read-only. If you are
    migrating from ar71xx and used the method mentioned above to
    upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more
    method for doing this is described below.

  - Migrating directly from ar71xx has not been thoroughly tested, but
    one method has been used a couple of times with good success,
    migrating 18.06.2 to a full image produced as of this commit. Please
    note that these instructions are only for experienced users, and/or
    those still able to open their device up to flash it via the serial
    headers should anything go wrong.

    1) Install kmod-mtd-rw and uboot-envtools
    2) Run `insmod mtd-rw.ko i_want_a_brick=1`
    3) Modify /etc/fw_env.config to point to the u-boot-env partition.
       The file /etc/fw_env.config should contain:

       # MTD device   env offset  env size    sector size
       /dev/mtd1      0x00000     0x10000     0x10000

       See https://openwrt.org/docs/techref/bootloader/uboot.config
       for more details.

    4) Run `fw_printenv` to verify everything is correct, as per the
       link above.
    5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address.
    6) Manually modify /lib/upgrade/common.sh's get_image function:
       Change ...

       cat "$from" 2>/dev/null | $cmd

       ... into ...

       (
         dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes
         echo -ne '\x00\x18\x0a\x12\x34\x56'  ; # Add in MAC address
         dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest
         cat "$from" 2>/dev/null
       ) | $cmd

       ... which, during the upgrade process, will pad the image by
       128K of zeroes-plus-MAC-address, in order for the ar71xx's
       firmware partition -- which starts at 0xbf080000 -- to be
       instead aligned with the ath79 firmware partition, which
       starts 128K later at 0xbf0a0000.

    7) Copy the sysupgrade image into /tmp, as above
    8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait

    Again, this may BRICK YOUR DEVICE, so make *sure* to have your
    serial cable handy.

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[add LED migration and extend compat message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 16:56:08 +01:00
Ewan Parker
ddafcc7947 ramips: add support for Hi-Link HLK-7688A
Specifications:

  - SoC: MediaTek MT7688AN
  - RAM: 128 MB
  - Flash: 32 MB
  - Ethernet: 5x 10/100 (1x WAN, 4x LAN)
  - Wireless: built in 2.4GHz (bgn)
  - USB: 1x USB 2.0 port
  - Buttons: 1x Reset
  - LEDs: 1x (WiFi)

Flash instructions:

  - Configure TFTP server with IP address 10.10.10.3
  - Name the firmware file as firmware.bin
  - Connect any Ethernet port to the TFTP server's LAN
  - Choose option 2 in U-Boot
  - Alternatively choose option 7 to upload firmware to the built-in
    web server

MAC addresses as verified by OEM firmware:

  use   address   source
  2g    *:XX      factory 0x4
  LAN   *:XX+1    factory 0x28
  WAN   *:XX+1    factory 0x2e

Notes:

This board is ostensibly a module containing the MediaTek MT7688AN SoC,
128 MB DDR2 SDRAM and 32 MB flash storage.  The SoC can be operated in
IoT Gateway Mode or IoT Device Mode.

From some vendors the U-Boot that comes installed operates on UART 2
which is inaccessible in gateway mode and operates unreliably in the
Linux kernel when using more than 64 MB of RAM.  For those, updating
U-Boot is recommended.

Signed-off-by: Ewan Parker <ewan@ewan.cc>
[add WLAN to 01_leds]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-05 14:54:47 +01:00
John Audia
36c9cf3e51 kernel: bump 5.4 to 5.4.95
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Removed upstreamed patches:
 imx6: 303-ARM-dts-imx6qdl-gw52xx-fix-duplicate-regulator-namin.patch

Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-04 22:07:32 +01:00
Daniel González Cabanelas
a0e0e621ca bcm63xx: sprom: override the PCI device ID
The PCI device ID detected by the wifi drivers on devices using a fallback
SPROM is wrong. Currently the chipnum is used for this parameter.

Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on
devices without a physical SPROM, the only one way to detect if the device
suports both bands or only the 5GHz band, is by reading the device ID from
the fallback SPROM.

In some devices, this may lead to a non working wifi on a 5GHz-only card,
or in the best case a working 2.4GHz-only in a dual band wifi card.

The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is
0x0060. This is true for any SPROM version.

Override the PCI device ID with the one defined at the fallback SPROM, to
detect the correct wifi card model and allow using the 5GHz band if
supported.

The patch has been tested with the following wifi radios:

BCM43222: b43: both 2.4/5GHz working
          brcm-wl: both 2.4/5GHz working

BCM43225: b43: 2.4GHz, working
	 brcmsmac: working
	 brcm-wl: it lacks support

BCM43217: b43: 2.4GHz, working
	 brcmsmac: it lacks support
	 brcm-wl: it lacks support

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[amend commit description, rework patch to avoid using a new global variable
and keep ssb sprom extraction code as close to ssb/pci.c as possible]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-02 20:40:31 +01:00
Álvaro Fernández Rojas
e23a90674e bcm63xx: backport upstream SSB SPROM extraction
New upstream changes extract more SPROM values and fix the antenna gain.
These changes can be found in linux drivers/ssb/pci.c.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-02 20:40:29 +01:00
John Audia
d33cd383ed kernel: bump 5.4 to 5.4.94
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
2021-02-01 19:10:43 +01:00
Leon Leijssen
eff03cea27 ath79: ag71xx: add ethtool statistics support
Add statistics to ethtool. The statistics can be useful to
debug network issues.

The code is backported from mainline ag71xx.c driver.

Signed-off-by: Leon Leijssen <leon.git@leijssen.info>
2021-02-01 00:48:12 +01:00
David Bauer
51f578efa5 ath79: add support for Ubiquiti UniFi AP Outdoor+
Hardware
--------
Atheros AR7241
16M SPI-NOR
64M DDR2
Atheros AR9283 2T2R b/g/n
2x Fast Ethernet (built-in)

Installation
------------

Transfer the Firmware update to the device using SCP.

Install using fwupdate.real -m <openwrt.bin> -d

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-01 00:47:46 +01:00
David Bauer
0c499f6068 mac80211: convert UniFi Outdoor+ HSR support to OF
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-01 00:47:36 +01:00
Petr Štetiar
337ff74894 mvebu: omnia: make initramfs image usable out of the box
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree.  Fix it by producing FIT based image which could be booted with
following commands:

 setenv bootargs earlyprintk console=ttyS0,115200
 tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
 bootm ${kernel_addr_r}

Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2021-01-31 11:39:19 +01:00
Daniel González Cabanelas
24b910dca2 mvebu: LS421DE: fix the thermal zones
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.

Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).

In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.

(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)

Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2021-01-30 01:03:00 +01:00
INAGAKI Hiroshi
eb11cd9ea3 ramips: add support for ELECOM WRC-2533GHBK-I
ELECOM WRC-2533GHBK-I is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB
- Flash		: SPI-NOR 16 MiB
- WLAN		: 2.4/5 GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LED/keys	: 4x/3x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, RX, GND, TX from SoC side
  - 57600n8
- Power		: 12VDC, 1.5A

Flash instruction using factory image:

1. Boot WRC-2533GHBK-I normally
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~150 seconds to complete flashing

MAC addresses:

LAN	: BC:5C:4C:xx:xx:89 (Config, ethaddr (text))
WAN	: BC:5C:4C:xx:xx:88 (Config, wanaddr (text))
2.4GHz	: BC:5C:4C:xx:xx:8A (Factory, 0x4    (hex))
5GHz	: BC:5C:4C:xx:xx:8B (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-01-29 15:32:07 +01:00
INAGAKI Hiroshi
0071c7cd82 build: add elecom-product-header for ELECOM devices
A header used in ELECOM WRC-300GHBK2-I and WRC-1750GHBK2-I/C is also
used in ELECOM WRC-2533GHBK-I, so split the code to generate the header
and move it to image-commands.mk to use from ramips target.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
2021-01-29 15:28:12 +01:00
Adrian Schmutzler
331892f85f treewide: drop shebang from non-executable lib files
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.

Fix execute bit in one case, too.

This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-29 14:29:41 +01:00
John Audia
2c35899d81 kernel: bump 5.4 to 5.4.93
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system:       x86_64
Build-tested:       ipq806x/R7800, bcm27xx/bcm2711
Run-tested:         ipq806x/R7800
Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64
Run-tested [*]:     ath79/generic, ipq40xx, octeon, ramips/mt7621

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-29 14:22:09 +01:00
Álvaro Fernández Rojas
7d12f29ae1 bcm63xx: fix bcm63xx ethernet kernel panics
Calling netdev_reset_queue() from _stop() functions is causing sporadic kernel
panics on bcm63xx, which happen mainly on BCM6318 and BCM6328.
This reverts to the previous behaviour, which called netdev_reset_queue() from
_open() functions.

Tested on Comtrend AR-5315u (BCM6318).

Fixes: 1d6f422e34 ("bcm63xx: sync ethernet driver with net-next")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-01-28 12:01:14 +01:00
Jiang Yongquan
799fca7602 sunxi: add support for linksprite pcDuino3 nano board
Specifications:

 - SoC: Allwinner A20 @ 1Ghz
 - DRAM: 1GiB DDR3 @ 408MHz (K4B4G1646Q-HYK0)
 - NAND: 4GB MLC NAND (H27UBG8T2BTR-BC)
 - Ethernet: 10/100/1000Mbps Ethernet (Realtek RTL8211E)

Flash instructions:

dd if=openwrt-sunxi-cortexa7-linksprite_pcduino3-nano-ext4-sdcard.img
of=/dev/sdX

Signed-off-by: Jiang Yongquan <woxwchc@foxmail.com>
[Remove CONFIG_REALTEK_PHY from sunxi/cortexa53 config]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-01-27 23:14:30 +01:00
Marty Jones
9c29165a4c rockchip: fix SUPPORTED_DEVICES for Radxa ROCK Pi 4
This sets SUPPORTED_DEVICES to match the compatible in the DTS.

While at it, synchronize the capitalization in DEVICE_MODEL and
DTS model.

Signed-off-by: Marty Jones <mj8263788@gmail.com>
[commit title/message facelift, move variable in armv8.mk]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
30651e6834 bcm4908: sort and wrap build recipes
This sorts the Build recipes alphabetically, wraps some long lines
and moves the DEVICE_VARS to the top like common on several other
targets.

Cc: Rafał Miłecki <rafal@milecki.pl>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
44f2d71edd mediatek: remove generic profiles
We have support for reference boards available on this target, so
support for an additional generic profile does not make much sense.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
a7904c6b7f kirkwood: remove generic profile
On a platform with many very different devices, like found on kirkwood,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
5b0644b71d ipq806x: remove generic profile
On a platform with many very different devices, like found on ipq806x,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
5697915a18 ipq40xx: remove generic profile
On a platform with many very different devices, like found on ipq40xx,
the generic profile seems like a remnant of the past that does not
have a real use anymore.

Remove it to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
703fd8aef4 ramips: remove generic profiles
On a platform with many very different devices, like found on ramips,
the generic profiles seem like remnants of the past that do not
have a real use anymore.

Remove them to have one thing less to maintain.

Actually, rt288x didn't have a default profile in the first place.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Adrian Schmutzler
9b5e9b65cf ath79: remove generic profiles
On a platform with many very different devices, like found on ath79,
the generic profiles seem like remnants of the past that do not
have a real use anymore.

Remove them to have one thing less to maintain.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Felix Fietkau
ff9846dbb9 ramips: use lzma-loader on zbtlink devices
Fixes boot loader LZMA decompression issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2021-01-27 18:26:53 +01:00
Birger Koblitz
1b1bb6bf19 realtek: add debugfs support for mirroring
This adds debugfs support to monitor mirroring via debugfs

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
6f67c079e6 realtek: add API for the hw tables of RTL83XX/93XX SoCs
Add a table API that has per accss register locking and uses
register description information to handle all table access
through a single set of api calls.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
27029277f9 realtek: add switch driver support for the RTL93XX based switches
Adds support for the RTL9300 and RTL9310 series of switches
with 10GBit per port and up to 56 ports.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
d140b9fc23 realtek: add internal and external SDS/PHYs of RTL9300 devices
This adds support for the internal SerDes of the RTL9300 SoC
and for the RTL8218D and RTL8226B phys found in combination
with this SoC in switches.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
e1bca7c77d realtek: fix RTL8231 gpio expander usage with RTL839X SoC
This fixes the usage of the RTL8231 GPIO extender chip
when used with the RTL839X SoCs. Specifically,
the PHY addresses may be different from 0.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
6aac20bc01 realtek: enable default rate limiting and qos settings
Enable default rate limiting and QoS support. Remove
previous storm control code.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
56ac4fced0 realtek: correct l2 offloading tag handling
Makes sure the DSA trailer information on any L2 offloading done
by the switch is honoured by the bridge layer

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
dc9cc0d3e2 realtek: add QoS and rate control
This adds support for identifying QoS information in packets
and use this and rate control information to submit to multiple
egress queues. The ethernet driver is also made to support
2 egress and up to 32 egress queues.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
4237488cf3 realtek: add dtsi for RTL930X SoCs
Add a default dtsi to support RTL930X SoCs.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
8faffa00cb realtek: add support for the RTL9300 timer
this adds support for the SoC timer of the RTL9300 chips, it
provides 6 independent timer/counters, of which the first one
is used as a clocksource and the second one as event timer.

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
03c79ca269 realtek: add support for the RTL8390 and RTL9300 SoC IRQs
This adds support for the RTL8390 and RTL9300 SoCs
it also cleans up unnecessary definitions in mach-rtl83xx.h
and moves definitions relevant for irq routing to irq.h

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
Birger Koblitz
cb39602399 realtek: add detection of RTL930X SoCs and RTL8313 SoC
This adds support to detect RTL930X based SoCs and the RTL9313 SoC.
Tested on Zyxel XGS1210-10 (RTL9302B SoC) and the
Zyxel XS1930-12 (RTL9313 SoC)

Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
2021-01-26 15:06:50 +01:00
John Audia
9ad912d159 kernel: bump 5.4 to 5.4.92
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.

Build system:       x86_64
Build-tested:       ipq806x/R7800, bcm27xx/bcm2711
Run-tested:         ipq806x/R7800
Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon,
                    ramips/mt7621, realtek, x86/64.
Run-tested [*]:     ath79/generic, octeon, ramips/mt7621, realtek.

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
2021-01-26 00:49:53 +01:00
Tony Ambardar
0faa172356 config: limit CONFIG_PERF_EVENTS to top-level generic configs
Remove redundant target-level settings.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-01-25 14:37:41 +01:00
Tony Ambardar
b67d086ef3 malta: update target configs and fix build warnings
Comment out some conflicting target configs that are set from subtarget
configs, which sometimes lead to kernel compile warnings:

  scripts/kconfig/conf  --syncconfig Kconfig
  net/sched/Kconfig:45: warning: menuconfig statement without prompt
  .config:1038:warning: override: CPU_MIPS32_R2 changes choice state

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2021-01-25 14:37:41 +01:00
Bjørn Mork
1fb413e657 realtek: build ZyXEL vendor firmware compatible initramfs
Append a device specific version trailer used by the stock
firmware upgrade application to validate firmwares.

The trailer contains a list of ZyXEL firmware version
numbers, which includes a four letter hardware identifier.
The stock web UI requires that the current hardware matches
one of the listed versions, and that the version number is
larger than a model specific minimum value. The minimum
version varies between V1.00 and V2.60 for the currently
known GS1900 models. The number is not used anywhere else
to our knowlege, and has no direct relation to the version
info in the u-image header.  We can therefore use an
arbitrary value larger than V2.60.

The stock firmware upgrade application will only load and
flash the part of the file specified in the u-image header,
regardless of file size.  It can therefore not be used to
flash images with an appended rootfs. There is therefore no
need to include the trailer in other images than the
initramfs. This prevents accidentally bricking by attempts
to flash other images from the stock web UI.

Stock images support all models in the series, listing
all of them in the version trailer.  OpenWrt provide model
specific images.  We therefore only list the single supported
hardware identifier for each image.  This eliminates the risk
of flashing the wrong OpenWrt image from stock web UI.

OpenWrt can be installed from stock firmware in two steps:

   1) flash OpenWrt initramfs image from stock web gui
   2) boot OpenWrt and sysupgrade to a squasfs image

The OpenWrt squashfs image depends on a static partition
map in the DTS.  It can only be installed to the "firmware"
partition.  This partition is labeled "RUNTIME1" in u-boot
and in stock firmware, and is referred to as "image 0" in
the stock flash management tool.  The OpenWrt initramfs
can be installed and run from either partitions. But if
you want to keep stock irmware in the spare system partition,
then you must make sure stock firmware is installed to the
"RUNTIME2" partition referred to as "image 1" in the stock
web UI. And the initial OpenWrt initramfs must be flashed
to "RUNTIME1"/"image 0".

The stock flash management application supports direct
selection of both which partition to flash and which
partition to boot next.  This allows software controlled
"dual-boot" between OpenWrt and stock firmware, without
using console access to u-boot. u-boot use the "bootpartition"
variable stored in the second u-boot environment to select
which of the two system partitions to boot.  This variable
is set by the stock flash management application, by direct
user input.  It can also be set in OpenWrt using e.g

 fw_setsys bootpartition 1

to select "RUNTIME2"/"image 1" as default, assuming a
stock firmware version is installed in that partition.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-24 18:12:34 +01:00
Bjørn Mork
ca4832fcac realtek: use vendor-specific magic for ZyXEL
The stock firmware of the ZyXEL GS1900 series use a non-standard
u-image magic.  This is not enforced by the stock u-boot, which is
why we could boot images with the default magic.  The flash
management application of the stock firmware will however verify
the magic, and refuse any image with another value.

Convert to vendor-specific value to get flash management support
in stock firmware, including the ability to upgrade to OpenWrt
directly from stock web UI.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-24 18:12:34 +01:00
Adrian Schmutzler
29167cbca3 x86: fix upgrade by emptying SUPPORTED_DEVICES
x86 uses append-metadata, but only for signing and not for the
metadata itself.

Since recently SUPPORTED_DEVICES was assigned with a global value
and is not empty anymore, append-metadata will now actually put
metadata into x86 images. This breaks sysupgrade on x86.

To fix it for the moment, let's just empty SUPPORTED_DEVICES for
this target again.

In the long term, one should either not add metadata to the images
if it is not desired, and/or remove the unintended fwtool check.

Fixes: f52081bcf9 ("treewide: provide global default for SUPPORTED_DEVICES")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 23:42:47 +01:00
Adrian Schmutzler
4571ef48d8 bcm53xx: use default SUPPORTED_DEVICES for Meraki MR32
Since the new global SUPPORTED_DEVICES are now available in bcm53xx
as well, we do not need to specify an explicit value for the MR32
anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 23:42:47 +01:00
Michael Pratt
96017a6013 ath79: add support for Senao Engenius EAP1200H
FCC ID: A8J-EAP1200H

Engenius EAP1200H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9557 SOC
  - QCA9882 WLAN	PCI card, 5 GHz, 2x2, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:a2 art 0x0
  phy1 2.4G *:a3 ---
  phy0 5GHz *:a4 ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  *DISCLAIMER*
  The Failsafe image is unique to Engenius boards.
  If the failsafe image is missing or damaged this will brick the device
  DO NOT downgrade to ar71xx this way, it can cause kernel loop or halt

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times

**Format of OEM firmware image:**

  The OEM software of EAP1200H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1200h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1200h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-01-23 12:53:22 +01:00
Adrian Schmutzler
f52081bcf9 treewide: provide global default for SUPPORTED_DEVICES
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:

  SUPPORTED_DEVICES := $(subst _,$(comma),$(1))

At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:

  device/image name:  vendor_model
  compatible:         vendor,model

The equal redundant definitions are a symptom of this process.

Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.

This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-23 12:45:21 +01:00
Bjørn Mork
402408b368 kernel: mtdsplit_uimage: replace "edimax, uimage" parser
The "edimax,uimage"" parser can be replaced by the generic
parser using device specific openwrt,partition-magic and
openwrt,offset properties.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
3f36dffbde kernel: mtdsplit_uimage: add "openwrt, offset" and "openwrt, partition-magic"
Some devices prepend a standard U-Boot Image with a vendor specific
header, having its own magic. Adding two new properties will support
validation of such images, including the additional magic.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
ff7709d223 kernel: mtdsplit_uimage: replace "netgear, uimage" parser
The "netgear,uimage" parser can be replaced by the generic
parser using device specific openwrt,ih-magic and
openwrt,ih-type properties.

Device tree properties for the following devices have not
been set, as they have been dropped from OpenWrt with the
removal of the ar71xx target:

 FW_MAGIC_WNR2000V1     0x32303031
 FW_MAGIC_WNR2000V4     0x32303034
 FW_MAGIC_WNR1000V2_VC  0x31303030
 FW_MAGIC_WPN824N       0x31313030

Tested-by: Sander Vanheule <sander@svanheule.net>  # WNDR3700v2
Tested-by: Stijn Segers <foss@volatilesystems.org> # WNDR3700v1
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
de64d4b958 kernel: mtdsplit_uimage: add "openwrt, ih-type" device-tree property
Some devices use uimage headers with a non-default ih_type. Add
support for overriding this in device tree.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
647fdafcc5 kernel: mtdsplit_uimage: replace "allnet, uimage" parser
Convert users to the generic "openwrt,uimage" using device specific
"openwrt,ih-magic" properties, and remove "allnet,uimage".

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
01a1e21863 kernel: mtdsplit_uimage: replace "openwrt, okli" parser
The only difference between the "openwrt,okli" and the generic
parser is the magic.  Set this in device tree for all affected
devices and  remove the "openwrt,okli" parser.

Tested-by: Michael Pratt <mcpratt@protonmail.com> # EAP300 v2, ENS202EXT and ENH202
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
ed39f7ec1a kernel: mtdsplit_uimage: add "openwrt, ih-magic" device-tree property
Many devices use uimages with non-standard magic values. Let
device tree override the default magic.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
5ab5bacda2 kernel: mtdsplit_uimage: replace "fonfxc" and "sge" parsers
Convert users of the "fonfxc" and "sge" parsers to the generic
"openwrt,uimage", using device specific "openwrt,padding" properties.

Tested-by: Stijn Segers <foss@volatilesystems.org> [DIR-878 A1]
Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
76ea7a91cf kernel: mtdsplit_uimage: read extralen from device tree
An "openwrt,padding" property in device tree can replace two device
specific parsers.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Bjørn Mork
dd5ac0546c dt-bindings: mtd: partitions: add OpenWrt defined U-Boot Image
Add devicetree bindings for vendor specific variants of U-Boot
Images, as defined by OpenWrt.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2021-01-22 21:03:11 +01:00
Rafał Miłecki
20b4f77bb6 kernel: add parser finding rootfs after CFE bootfs
It's required for BCM4908. It cannot use "bcm-wfi-fw" parser because
that one requires *two* JFFS2 partitions which is untested / unsupported
on the BCM4908 architecture. With a single JFFS2 partition "bcm-wfi-fw"
parser will:
1. Fail to find "vmlinux.lz" as it doesn't follow "1-openwrt" file
2. Create partitions that don't precisely match bootfs layout

The new parser is described in details in the MTD_SPLIT_CFE_BOOTFS
symbol help message.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-22 20:14:39 +01:00
Rafał Miłecki
6ba3a0e889 bcm4908: build valid Asus GT-AC5300 firmware image
Insert Asus specific tail that is required for image identification.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-22 20:11:24 +01:00
Sieng Piaw Liew
1d6f422e34 bcm63xx: sync ethernet driver with net-next
Sync ethernet driver code with upstream Linux kernel:
-Reduce xmit_more code changes.
-Combine rx cleanup code into a function.
-Convert to build_skb.
-Improve rx loop by optimizing loop tracking.

https://lore.kernel.org/netdev/20210106144208.1935-1-liew.s.piaw@gmail.com/
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
[Amend commit description, move patches to the top since they are going to be
upstreamed]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-01-22 12:42:30 +01:00
Álvaro Fernández Rojas
2d8422842c bcm63xx: nand: fix OOB R/W for non Hamming ECC
Hamming ECC devices do not cover OOB data, as opposed to BCH ECC devices.
Therefore, disabling ECC for all devices is preventing BCH devices from
correctly reading and writing the OOB data.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-01-22 11:36:49 +01:00
Adrian Schmutzler
b3eccbca7c ramips: fix port labels for Xiaomi Mi Router 4
The OEM assignment of LAN ports is swapped.

Fixes: c2a7bb520a ("ramips: mt7621: add support for Xiaomi Mi Router 4")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:56:43 +01:00
Dmytro Oz
c2a7bb520a ramips: mt7621: add support for Xiaomi Mi Router 4
Xiaomi Mi Router 4 is the same as Xiaomi Mi Router 3G, except for
the RAM (256Mib→128Mib), LEDs and gpio (MiNet button).

Specifications:

Power: 12 VDC, 1 A
Connector type: barrel
CPU1: MediaTek MT7621A (880 MHz, 4 cores)
FLA1: 128 MiB (ESMT F59L1G81MA)
RAM1: 128 MiB (ESMT M15T1G1664A)
WI1 chip1: MediaTek MT7603EN
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: U.FL
WI2 chip1: MediaTek MT7612EN
WI2 802dot11 protocols: an+ac
WI2 MIMO config: 2x2:2
WI2 antenna connector: U.FL
ETH chip1: MediaTek MT7621A
Switch: MediaTek MT7621A

UART Serial
[o] TX
[o] GND
[o] RX
[ ] VCC - Do not connect it

MAC addresses as verified by OEM firmware:

use   address   source
LAN   *:c2      factory 0xe000 (label)
WAN   *:c3      factory 0xe006
2g    *:c4      factory 0x0000
5g    *:c5      factory 0x8000

Flashing instructions:

1.Create a simple http server (nginx etc)
2.set uart enable
To enable writing to the console, you must reset to factory settings
Then you see uboot boot, press the keyboard 4 button (enter uboot command line)
If it is not successful, repeat the above operation of restoring the factory settings.
After entering the uboot command line, type:

setenv uart_en 1
saveenv
boot

3.use shell in uart
cd /tmp
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin
wget http://"your_computer_ip:80"/openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-kernel1.bin kernel1
mtd write openwrt-ramips-mt7621-xiaomi_mir4-squashfs-rootfs0.bin rootfs0
nvram set flag_try_sys1_failed=1
nvram commit
reboot
4.login to the router http://192.168.1.1/

Installation via Software exploit
Find the instructions in the https://github.com/acecilia/OpenWRTInvasion

Signed-off-by: Dmytro Oz <sequentiality@gmail.com>
[commit message facelift, rebase onto shared DTSI/common device
definition, bump uboot-envtools]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:53:19 +01:00
Adrian Schmutzler
93be5926a2 ramips: mt7621: create DTSI for Xiaomi NAND devices
This creates a DTSI for Xiaomi devices with 128M NAND.

This allows to consolidate the partitions and a few other nodes for
AC2100 family and Mi Router 3G.

Note that the Mi Router 3 Pro has 256M NAND and differently sized
partitions.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:52:02 +01:00
Adrian Schmutzler
5a46b71826 ramips: mt7621: reorganize shared device definitions for Xiaomi
This creates a shared device definition for Xiaomi devices with
NAND and "separate" images, i.e. kernel1.bin and rootfs0.bin.

This allows to consolidate similar/duplicate code for AC2100 family
and Mi Router 3G.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-01-21 22:52:02 +01:00
Robert Marko
36347d003a ipq40xx: fix boards being shown twice
Since generic images have been split to their own
Makefile boards are showing up twice in menuconfig
as $(eval $(call BuildImage)) was not dropped from
the new generic.mk.

Hence $(eval $(call BuildImage)) was being called
twice.

So, lets simply drop it from generic.mk.

Fixes: 378c7ff282 ("ipq40xx: split generic images into own file")

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2021-01-21 17:08:16 +01:00
Rafał Miłecki
3bd8f660a4 bcm4908: workaround NAND controller #WP issue
There seems to be a problem with setting #WP. On the other hand ignoring
the #WP seems to work. rootfs_data UBI volume seems to persist changes.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 13:30:20 +01:00
Rafał Miłecki
e78d3e44dd bcm4908: append UBI with rootfs to device images
Also enable UBI kernel support.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 13:25:34 +01:00
Rafał Miłecki
4e1e18af65 bcm4908: build flashable & bootable firmware images
BCM4908 bootloader requires firmware with JFFS2 image containing:
1. cferam.000
2. 94908.dtb
3. vmlinux.lz
4. device custom files

cferam.000 can be obtained from the bcm63xx-cfe repository.
device custom files are stored in images dir.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 13:18:42 +01:00
Rafał Miłecki
095ed5e8e1 bcm4908: set console in the CONFIG_CMDLINE
procd doesn't work with just serial specified in the DT (using chosen &
stdout-path). It requires tty device to be explicitly specified in the
cmdline.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-21 09:18:31 +01:00
Rafał Miłecki
e6fb4d08a1 bcm4908: add DTS patches for USB PHY and partitions
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 22:00:22 +01:00
Rafał Miłecki
bc3dbd68c4 bcm4908: use backported brcmstb soc stubs patch
Final version differs slightly - uses IS_ENABLED()

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 22:00:18 +01:00
Rafał Miłecki
707ad89f06 bcm4908: use backported switch & PMB DTS patches
Final versions differ slightly from what was used initially.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 22:00:15 +01:00
Rafał Miłecki
20a0d435d8 bcm4908: add pending mtd patches for BCM4908 partitioning
BCM4908 can have multiple firmware partitions. MTD needs to detect which
one is currently used.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 07:47:29 +01:00
Rafał Miłecki
7495acb555 kernel: backport mtd commit converting partitions doc syntax
1. It's useful for developing & validating DTS files inside OpenWrt
2. This will allow backporting later changes that depend on it

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-01-20 07:47:23 +01:00