The allows userspace LEDs to be created and controlled. This can be useful
for testing triggers and can also be used to implement virtual LEDs.
Signed-off-by: Keith T. Garner <kgarner@kgarner.com>
[squash fixup commit and improve option wording]
Signed-off-by: Paul Spooren <mail@aparcar.org>
The code uses get_mtd_device_nm() which must be followed by a call to
put_mtd_device() once the handle is no longer used.
This fixes spurious shutdown console messages such as:
[ 2256.334562] Removing MTD device #7 (soft_config) with use count 1
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
311-MIPS-zboot-put-appended-dtb-into-a-section.patch
commit d2e850e96183 in kernel, part of v5.11
499-mtd-don-t-lock-when-recursively-deleting-partitions.patch
commit cb4543054c5c in kernel, part of v5.13
103-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch
commit 5a4fa44f5e1b in kernel, part of v5.13
Move them to backports folder to make maintainance easier.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
MAC addresses read from official firmware
value location
Wlan xx 71 de factory@0x04
Lan xx 71 dd factory@0x28
Wan xx 71 df factory@0x2e
Label xx 71 dd factory@0x28
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
186af01047b2 mt76: mt7921: introduce MCU_EVENT_LP_INFO event parsing
93b5c28c97d5 mt76: mt7921: add rcu section in mt7921_mcu_tx_rate_report
a8e89c5a1d1f mt76: testmode: add support to send larger packet
a0cc9a9e3877 mt76: mt7915: rework mt7915_tm_set_tx_len()
c8b96630324e mt76: mt7915: fix rate setting of tx descriptor in testmode
22fd2958c42a mt76: mt7615: fix memleak when mt7615_unregister_device()
7401e0db3143 mt76: mt7915: fix memleak when mt7915_unregister_device()
c3656268b3f6 mt76: mt7915: only free skbs after mt7915_dma_reset() when reset happens
0ce955b04ba8 mt76: mt7615: only free skbs after mt7615_dma_reset() when reset happens
b03d1e62acf7 mt76: mt7615: use ieee80211_free_txskb() in mt7615_tx_token_put()
5ac02e22fb03 mt76: flush tx status queue on DMA reset
c71f609b398a mt76: sync with upstream changes
23ecadd4af77 mt76: mt7615: fix hardware error recovery for mt7663
57a899ee3c3c mt76: mt7615: fix entering driver-own state on mt7663
42a2dddb706b mt76: mt7615: load ROM patch before checking patch semaphore status
cf0e406af84a mt76: mt7915: add support for applying pre-calibration data
459940ccbc58 mt76: mt7921: move hw configuration in mt7921_register_device
0a094b11f3c0 mt76: improve mcu error logging
bf536832e37d mt76: mt7921: run mt7921_mcu_fw_log_2_host holding mt76 mutex
7616f4f78163 mt76: mt7921: add wifisys reset support in debugfs
e620bd881ef5 mt76: mt7921: abort uncompleted scan by wifi reset
e8dacf59ab1c mt76: mt7915: rework the flow of txpower setting
c8c78e577236 mt76: mt7915: directly read per-rate tx power from registers
1622bf4f8705 mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device
ef96fafad8a9 mt76: Convert to DEFINE_SHOW_ATTRIBUTE
90e4bfea2948 mt76: mt7921: do not use 0 as NULL pointer
0a139d7f5966 mt76: connac: move mcu_update_arp_filter in mt76_connac module
de26c73ce3c2 mt76: mt7921: remove leftover function declaration
1c0b6cb4f942 mt76: mt7921: fix a race between mt7921_mcu_drv_pmctrl and mt7921_mcu_fw_pmctrl
2923e3e2b8e4 mt76: mt7663: fix a race between mt7615_mcu_drv_pmctrl and mt7615_mcu_fw_pmctrl
74d0fdaa7a99 mt76: connac: introduce wake counter for fw_pmctrl synchronization
28c87e09a5ea mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
36f664edc7db mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
51b3d1a9a2b7 mt76: dma: add the capability to define a custom rx napi poll routine
4f1339c9fb72 mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
1bc5e67a60be mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
325f7b451c03 mt76: connac: unschedule ps_work in mt76_connac_pm_wake
12115052a02f mt76: connac: check wake refcount in mcu_fw_pmctrl
e5d28e3cef66 mt76: connac: remove MT76_STATE_PM in mac_tx_free
475112a3cdcc mt76: mt7921: get rid of useless MT76_STATE_PM in mt7921_mac_work
112998f32d85 mt76: connac: alaways wake the device before scanning
4334f3e2fc43 mt76: mt7615: rely on pm refcounting in mt7615_led_set_config
0562380659ad mt76: connac: do not run mt76_txq_schedule_all directly
acfa78df5708 mt76: connac: use waitqueue for runtime-pm
ca74a4cd0722 mt76: remove MT76_STATE_PM in tx path
0c2d3e74852e mt76: mt7921: add awake and doze time accounting
45e0eefffe9f mt76: mt7921: enable sw interrupts
fd2ff641166f mt76: mt7615: Fix a dereference of pointer sta before it is null checked
7e2521468767 mt76: mt7921: move mt7921_dma_reset in dma.c
c9dd6b1fa171 mt76: mt7921: introduce mt7921_wpdma_reset utility routine
2ac7c7e9c568 mt76: mt7921: introduce mt7921_dma_{enable,disable} utilities
662a89f2b9d1 mt76: mt7921: introduce mt7921_wpdma_reinit_cond utility routine
614efe9e9180 mt76: connac: introduce mt76_connac_mcu_set_deep_sleep utility
0dbb16ef39d8 mt76: mt7921: enable deep sleep when the device suspends
3c19f569cc70 mt76: mt7921: fix possible invalid register access
ade1f5aad4c6 mt76: move token_lock, token and token_count in mt76_dev
8d5c456be1ff mt76: move token utilities in mt76 common module
fb04d9df5e52 mt76: mt7915: do not read rf value from efuse in flash mode
2126b2176336 mt76: mt7921: get rid of mcu_reset function pointer
d325b7eff1b1 mt76: mt7921: improve doze opportunity
2ae25c7e547e mt76: mt7663: add awake and doze time accounting
349bbb9d6f13 mt76: connac: unschedule mac_work before going to sleep
98a235004dea mt76: mt7921: mt7921_stop should put device in fw_own state
63d80b9ab251 mt76: mt7921: introduce mt7921_mcu_sta_add routine
3c5bf837fdbd mt76: mt7615: fix a precision vs width bug in printk
ded14da5eacc mt76: mt7915: fix a precision vs width bug in printk
aaf0d254f9ea mt76: mt7921: fix a precision vs width bug in printk
757af5c67d32 mt76: move mt76_token_init in mt76_alloc_device
ed41ed73a495 mt76: mt7921: reinit wpdma during drv_own if necessary
92fb81e085c6 mt76: mt7921: fix possible AOOB issue in mt7921_mcu_tx_rate_report
53d915a23bc9 mt76: connac: do not schedule wake_work if the runtime-pm is disabled
23fe1bdcf15a mt76: connac: do not schedule mac_work if the device is not running
e5b19336c58e mt76: mt7615: do not set MT76_STATE_PM at bootstrap
0fc2136a61dd mt76_connac_mcu: move mt76_connac_mcu_update_arp_filter outside of CONFIG_PM
e693f3e23e06 mt76: mt7915: add MSI support
5231e7300fa4 mt7915: disable ASPM
554b50dabf54 mt76: connac: fix uninitialized HT A-MPDU setting field in STA_REC_PHY
43b9c0a838bb mt76: mt7921: fix max aggregation subframes setting
5a387a0a3004 mt76: mt7921: enable rx hw de-amsdu
c8cbcb87be07 mt76: connac: add missing configuration in mt76_connac_mcu_wtbl_hdr_trans_tlv
55921e57b380 mt76: mt7921: enable rx header traslation offload
01441f67d8b2 mt76: mt7921: enable rx csum offload
c9ab76dd93a0 mt76: mt7915: move mt7915_queue_rx_skb to mac.c
caedb4c4ee41 mt76: mt7615: fix fixed-rate tx status reporting
c6ae95d43e6d mt76: improve tx status codepath
27d468d094e6 mt76: mt7915: rework tx rate reporting
3b4ca5b09e2c mt76: mt7615: avoid use of ieee80211_tx_info_clear_status
e1f07d7f1cb9 mt76: mt7603: avoid use of ieee80211_tx_info_clear_status
18513ba5fbc2 mt76: mt7915: add support for tx status reporting
35f189cf81b2 mt76: mt7915: fix uninitialized variable in MSI error handling
9e928ac1ea9b mt76: dma: use ieee80211_tx_status_ext to free packets when tx fails
628eee9c386c mt76: fill queue entry wcid for all skbs with a station
a9bc4d94b7a1 mt76: intialize tx queue entry wcid to 0xffff by default
998ca8af7d17 mt76: mt7915: fix tssi indication field of DBDC NICs
7dd24b3cfacf mt76: mt7915: fix a signedness bug in mt7915_mcu_apply_tx_dpd()
535025d65d8d mt76: mt7915: cleanup mt7915_mcu_sta_rate_ctrl_tlv()
ff8bbe22dd87 mt76: mt7915: add .set_bitrate_mask() callback
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous commit bumped the source commit level without reflecting
that in PKG_SOURCE_DATA. Bump PKG_SOURCE_DATA as well.
Fixes: 97e820c6d6 ("rpcd: update to latest HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the CPU port to the unknown multicast flooding port mask,
which fixes the VLAN issues introduced by the multicast group patches
Tested-by: Russell Senior <russell@personaltelco.net> [Netgear GS108Tv3]
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no> [whitespace fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz> [unknwon typo fix]
The ZyXEL NR7101 is an 802.3at PoE powered 5G outdoor (IP68) CPE
with integrated directional 5G/LTE antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E
- Switch: 1 LAN port (Gigabiti)
- 5G/LTE: Quectel RG502Q-EA connected by USB3 to SoC
- SIM: 2 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/yellow under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to 5G/LTE bridge or
router. The Wifi interface is intended for installation and/or
temporary management purposes only.
UART Serial:
57600N1
Located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover, the WLAN button and 12 screws
holding the back plate and antenna cover together. The GPS antenna
is fixed to the cover, so be careful with the cable. Remove 4
screws fixing the antenna board to the main board, again being
careful with the cables.
A bluetooth TTL adapter is recommended for permanent console
access, to keep the router water and dustproof. The 3.3V pin is
able to power such an adapter.
MAC addresses:
OpenWrt OEM Address Found as
lan eth2 08:26:97:*:*:BC Factory 0xe000 (hex), label
wlan0 ra0 08:26:97:*:*:BD Factory 0x4 (hex)
wwan0 usb0 random
WARNING!!
ISP managed firmware might at any time update itself to a version
where all known workarounds have been disabled. Never boot an ISP
managed firmware with a SIM in any of the slots if you intend to use
the router with OpenWrt. The bootloader lock can only be disabled with
root access to running firmware. The flash chip is physically
inaccessible without soldering.
Installation from OEM web GUI:
- Log in as "supervisor" on https://172.17.1.1/
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Installation from OEM ssh:
- Log in as "root" on 172.17.1.1 port 22022
- scp OpenWrt initramfs-recovery.bin image to 172.17.1.1:/tmp
- Prepare bootloader config by running:
nvram setro uboot DebugFlag 0x1
nvram setro uboot CheckBypass 0
nvram commit
- Run "mtd_write -w write initramfs-recovery.bin Kernel" and reboot
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- (optional) Copy OpenWrt to the recovery partition. See below
- Sysupgrade to the OpenWrt sysupgrade image and reboot
Copying OpenWrt to the recovery partition:
- Verify that you are running a working OpenWrt recovery image
from flash
- ssh to root@192.168.1.1 and run:
fw_setenv CheckBypass 0
mtd -r erase Kernel2
- Wait while the bootloader mirrors Image1 to Image2
NOTE: This should only be done after successfully booting the OpenWrt
recovery image from the primary partition during installation. Do
not do this after having sysupgraded OpenWrt! Reinstalling the
recovery image on normal upgrades is not required or recommended.
Installation from Z-Loader:
- Halt boot by pressing Escape on console
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Type "ATNR 1,initramfs-recovery.bin" at the "ZLB>" prompt
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image
NOTE: ATNR will write the recovery image to both primary and recovery
partitions in one go.
Booting from RAM:
- Halt boot by pressing Escape on console
- Type "ATGU" at the "ZLB>" prompt to enter the U-Boot menu
- Press "4" to select "4: Entr boot command line interface."
- Set up a tftp server to serve the OpenWrt initramfs-recovery.bin
image at 10.10.10.3
- Load it using "tftpboot 0x88000000 initramfs-recovery.bin"
- Boot with "bootm 0x8800017C" to skip the 380 (0x17C) bytes ZyXEL
header
This method can also be used to RAM boot OEM firmware. The warning
regarding OEM applies! Never boot an unknown OEM firmware, or any OEM
firmware with a SIM in any slot.
NOTE: U-Boot configuration is incomplete (on some devices?). You may
have to configure a working mac address before running tftp using
"setenv eth0addr <mac>"
Unlocking the bootloader:
If you are unebale to halt boot, then the bootloader is locked.
The OEM firmware locks the bootloader on every boot by setting
DebugFlag to 0. Setting it to 1 is therefore only temporary
when OEM firmware is installed.
- Run "nvram setro uboot DebugFlag 0x1; nvram commit" in OEM firmware
- Run "fw_setenv DebugFlag 0x1" in OpenWrt
NOTE:
OpenWrt does this automatically on first boot if necessary
NOTE2:
Setting the flag to 0x1 avoids the reset to 0 in known OEM
versions, but this might change.
WARNING:
Writing anything to flash while the bootloader is locked is
considered extremely risky. Errors might cause a permanent
brick!
Enabling management access from LAN:
Temporary workaround to allow installing OpenWrt if OEM firmware
has disabled LAN management:
- Connect to console
- Log in as "root"
- Run "iptables -I INPUT -i br0 -j ACCEPT"
Notes on the OEM/bootloader dual partition scheme
The dual partition scheme on this device uses Image2 as a recovery
image only. The device will always boot from Image1, but the
bootloader might copy Image2 to Image1 under specific conditions. This
scheme prevents repurposing of the space occupied by Image2 in any
useful way.
Validation of primary and recovery images is controlled by the
variables CheckBypass, Image1Stable, and Image1Try.
The bootloader sets CheckBypass to 0 and reboots if Image1 fails
validation.
If CheckBypass is 0 and Image1 is invalid then Image2 is copied to
Image1.
If CheckBypass is 0 and Image2 is invalid, then Image1 is copied to
Image2.
If CheckBypass is 1 then all tests are skipped and Image1 is booted
unconditionally. CheckBypass is set to 1 after each successful
validation of Image1.
Image1Try is incremented if Image1Stable is 0, and Image2 is copied to
Image1 if Image1Try is 3 or larger. But the bootloader only tests
Image1Try if CheckBypass is 0, which is impossible unless the booted
image sets it to 0 before failing.
The system is therefore not resilient against runtime errors like
failure to mount the rootfs, unless the kernel image sets CheckBypass
to 0 before failing. This is not yet implemented in OpenWrt.
Setting Image1Stable to 1 prevents the bootloader from updating
Image1Try on every boot, saving unnecessary writes to the environment
partition.
Keeping an OpenWrt initramfs recovery as Image2 is recommended
primarily to avoid unwanted OEM firmware boots on failure. Ref the
warning above. It enables console-less recovery in case of some
failures to boot from Image1.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The ZyXEL NR7101 prepend an additional header to U-Boot images. This
header use the TRX magic 0x30524448 (HDR0), but is incompatible with
TRX images.
This code is reverse-engineered based on matching 32 bit numbers
found in the header with lengths and different checksum
calculations of the vendor images found on the device. The result
was matched against the validation output produced by the
bootloader to name the associated header fields.
Example bootloader validation output:
Zyxel TRX Image 1 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14177560)
kernelChksum : (0x8DD31F69)
swVersionInt : 1.00(ABUV.0)D1
swVersionExt : 1.00(ABUV.0)D1
Zyxel TRX Image 2 --> Found! Header Checksum OK
============ZyXEL header information==================
chipId : MT7621A
boardId : NR7101
modelId : 07 01 00 01
kernel_len : (14176660)
kernelChksum : (0x951A7637)
swVersionInt : 1.00(ABUV.0)D0
swVersionExt : 1.00(ABUV.0)D0
=================================================
Check image validation:
Image1 Header Magic Number --> OK
Image2 Header Magic Number --> OK
Image1 Header Checksum --> OK
Image2 Header Checksum --> OK
Image1 Data Checksum --> OK
Image2 Data Checksum --> OK
Image1 Stable Flag --> Stable
Image1 Try Counter --> 0
Image1: OK
Image2: OK
The coverage and algorithm for the kernelChksum field is unknown.
This field is not validated by the bootloader or the OEM firmware
upgrade tool. It is therefore set to a static value for now.
The swVersion fields contain free form string values. The OEM firmware
use ZyXEL structured version numbers as shown above. The strings are
not interpreted or validated on boot, so they can be repurposed for
anything we want the bootloader to display to the user. But the OEM
web GUI fails to flash images with freeform strings.
The purpose of the other strings in the header is not known. The
values appear to be static. We assume they are fixed for now, until
we have other examples. One of these strings is the platform name,
which is taken as an input parameter for support other members of
the device family.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
ath79, lantiq, ipq40xx, ramips all use the OpenWrt-specific gpio-export
functionality. Consolidate the patch that adds it under hack-5.10 since
this logic is obviously not target-specific. For those who want to
disable it, unsetting CONFIG_GPIO_SYSFS symbol will disable this code.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Kernel 5.10 support for ipq806x was added at the same time that these
patches were developed for kernel 5.4. This carries the patches forward
to kernel 5.10.
fa731838c5 ipq806x: dwmac: clear forced speed during probe
75ca641f1b ipq806x: Add "snps,dwmac" to all gmac compatible=
d62825dd77 ipq806x: dwmac: set forced speed when using fixed-link
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
d53be2a2e9 migrated 0069-arm-boot-add-dts-files.patch from patches-5.4
to patches-5.10, but a subsequent patch in that set, 1e25423be8,
erroneously removed several devices:
ipq8062/nec,wg2600hp3 from 3bb1618573
ipq8064/asrock,g10 from 98b86296e6
ipq8064/ubnt,unifi-ac-hd from 4e46beb313
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Run-tested: ipq806x/ubnt,unifi-ac-hd
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Add support for pstore/ramoops now that DRAM content is preserved
over reboot on MT7622. On each boot, check pstore and boot to recovery
image in case there are records stored in it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Most notably this enabled use of pstore/ramoops on MT7622 as DRAM
content is now preserved over reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switches to normalizing the partition names to lower case.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
fa731838c5 cleared the forced speed in the QSGMII PCS_ALL_CH_CTL
register during probe, but this is only correct for GMACs that are not
configured with fixed-link. This prevented GMACs configured with both
phy-mode = "sgmii" and fixed-link from working properly, as discussed at
https://github.com/openwrt/openwrt/pull/3954#issuecomment-834625090 and
the comments that follow. Notably, this prevented all communication
between gmac2 and the switch on the Netgear R7800.
The correct behavior is to set the QSGMII PCS_ALL_CH_CTL register by
considering the gmac's fixed-link child, setting the speed as directed by
fixed-link if present, and otherwise clearing it as was done previously.
Fixes: fa731838c5 ("ipq806x: dwmac: clear forced speed during probe")
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Run-tested: ipq806x/ubnt,unifi-ac-hd, ipq806x/netgear,r7800
Cc: Petr Štetiar <ynezz@true.cz>
Cc: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Ansuel Smith <ansuelsmth@gmail.com>
OpenWRT requires a number of Perl modules to be installed. It wasn't checking on all of them.
This patch adds checks for Perl FindBin, File::Copy, File::Compare and Thread::Queue modules.
Failing to install these, will have the build break at some point. By adding these to the
prereq-build.mk script, they are checked on forehand.
Tested on a Fedora 33 and 34 (beta) that was freshly installed. Fedora appears to
break up Perl modules into small packages that need to be installed for the build to succeed.
Signed-off-by: Bas Mevissen <abuse@basmevissen.nl>
With some debug in qmi.sh using following patch, some errors are visible
in the registration step
@@ -29,6 +29,7 @@ proto_qmi_init_config() {
}
proto_qmi_setup() {
+ set -x
local interface="$1"
local dataformat connstat plmn_mode mcc mnc
local device apn auth username password pincode delay modes pdptype
@@ -224,6 +225,8 @@ proto_qmi_setup() {
fi
done
+ registration=$(uqmi -s -d "$device" --get-serving-system)
+
[ -n "$modes" ] && uqmi -s -d "$device" --set-network-modes "$modes" > /dev/null 2>&1
echo "Starting network $interface"
During the boot of the system, modem could not start automatically its
network registration.
netifd: wan (9235): + echo 'Waiting for network registration'
netifd: wan (9235): Waiting for network registration
netifd: wan (9235): + local 'registration_timeout=0'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + grep '"searching"'
netifd: wan (9235): + uqmi -s -d /dev/cdc-wdm1 --get-serving-system
netifd: wan (9235): + registration='{"registration":"not_registered","plmn_mcc":208,"plmn_mnc":20,"plmn_description":"","roaming":true}'
netifd: wan (9235): + '[' -n ]
netifd: wan (9235): + echo 'Starting network wan'
As the while loop checks only "searching" pattern, uqmi.sh script quits
searching loop and continues whereas the modem is not registered
Other issue, after X seconds modem stops searching.
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + '[' -e /dev/cdc-wdm0 ]
netifd: wan (9213): + '[' 3 -lt 0 -o 0 '=' 0 ]
netifd: wan (9213): + let registration_timeout++
netifd: wan (9213): + sleep 1
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + grep '"searching"'
netifd: wan (9213): + uqmi -s -d /dev/cdc-wdm0 --get-serving-system
netifd: wan (9213): + registration='{"registration":"not_registered"}'
netifd: wan (9213): + '[' -n ]
netifd: wan (9213): + echo 'Starting network wan'
netifd: wan (9213): Starting network wan
If registration_timeout is not expired, registration can be restarted
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
Tested-by: Florian Eckert <fe@dev.tdt.de>
The routerbootparts driver dynamically discovers the location of MikroTik
partitions, but it cannot determine their size (except by extending them
up to the start of the next discovered partition).
The hard_config partition has a default size of 0x1000 in the driver,
while it actually takes 0x2000 on the hAP-ac2. Set the correct size in
the hAP-ac2 DTS.
On most devices, this isn't a problem as the actual data fits in 0x1000
bytes. However, some devices have larger data that doesn't fit in 0x1000
bytes. In any case, all devices seen so far have enough space for a
0x2000 hard_config partition before the start of the dtb_config partition.
With the current 0x1000 size:
0x00000000e000-0x00000000f000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
With this patch extending the size to 0x2000:
0x00000000e000-0x000000010000 : "hard_config"
0x000000010000-0x000000017bbc : "dtb_config"
Other ipq40xx boards may need the same fix but it needs testing.
References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324
Acked-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Using these config-options to customize the folders used at build-time makes these
folder settings appear in generated archive. This causes the SDK to be not
portable, as it's going to use the build-time folders on the new systems.
The errors vary from passing the build, disk out-of-space to permission denied.
The build-time settings of these folders are passed into the archive via Config.build.
The expected behavior is that the SDK acts after unpacking like these settings have
their defaults, using intree folders. So just filter these folders out when running
convert-config.pl to create Config.build.
This addresses the same issue that's fixed in the previous commit for the imagebuilder.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
Using these config-options to customize the folders used at build-time
makes these folder settings appear in generated archive. This causes the
imagebuilder to be not portable, as it's going to use the build-time folders
on the new systems. Errors look like:
mkdir: cannot create directory '/mnt/build': Permission denied
Makefile:116: recipe for target '_call_image' failed
make[2]: *** [_call_image] Error 1
Makefile:241: recipe for target 'image' failed
make[1]: *** [image] Error 2
The build-time settings of these folders are passed into the archives via
.config file.
The expected behavior is that after unpacking the imagebuilder acts like
these settings have their defaults, using intree folders. So unset the
build-time settings.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
The previous commit increased the U-Boot environment size of the
UniFi 6 LR to 0x4000. Also change it uboot-envtools accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
mtd erase needs to be aligned with erase blocks. Use padded image size
for erasing the production volume.
As the environment grew above the current size of 0x1000 bytes by
introducing the new padding function, increase the env size to 0x4000.
While at it, clean up reset button function to work to more reliable on
that board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adds support for Layer 2 multicast by implementing the DSA port_mdb_*
callbacks. The Kernel bridge listens to IGMP/MLD messages trapped to
the CPU-port, and calls the Multicast Forwarding Database updates.
The updates manage the L2 forwarding entries and the multicast
port-maps.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This sets up all VLANs with a default configuration on reset:
- forward based on VLAN-ID and not the FID/MSTI
- forward based on the inner VLAN-ID (not outer)
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds SoC specific VLAN configuration routines, which
alsoe sets up the portmask table entries that are referred to
in the vlan profiles registers for unknown multicast flooding.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds support for the MMD access registers the RTL-SoCs use to access clause 45
PHYs via mdio.
This new interface is used to add EEE-support for the RTL8226
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Adds a hash-bucket size attribute for the different SoCs, in order to
accomodate the buckets with 8 entries of the L2-forwarding tables
on RTL93XX in contrast to only 4 on RTL83XX.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds snooping support for IGMP and MLD on RTL8380/90/9300
by trapping IGMP and MLD packets to the CPU.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Enables CRC calculation offloading on RTL8380/8390/9300.
Tested on Zyxel XGS1210-10 (RTL9302)/GS1900-48 (RTL8390)/GS1900-10HP (RTL8382)
On the Zyxel GS1900-10HP, an increase of 5% in iperf3 send throughput
and 11% in receive throughput is seen.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
wakeup-source is required for gpio keys to fix error
genirq: irq_chip msmgpio did not update eff. affinity mask
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
- Add new tsens node
- Add new cpufreq required nodes
- Drop arm cpuidle compatible
- Fix duplicate node set upstream
- Add voltage tolerance value for cpu opp
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
