Commit Graph

212 Commits

Author SHA1 Message Date
Jianyu Zhuang
e0813dc071 mediatek: filogic: add support for Tenbay WR3000K
Tenbay WR3000K is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7981B.

- SoC: MetiaTek MT7981B
- RAM: Hynex H5TQ2G863GFR 512MiB
- Flash: Winbond W25N01GVZEIG 128MiB
- Wi-Fi: MediaTek MT7976C (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- MediaTek MT7915E: 2.4GHz and 5GHz
- Ethernet: 1x 10/100/1000 Mbps WAN + 3x 10/100/1000 Mbps LAN
- Switch: MediaTek MT7531AE
- UART: J4 (115200 baud)
- LEDs: Power
- Buttons: Reset, WPS
- PWR: 12V/1A DC, 5.5×2.1 connector

| Vendor  | OpenWrt Interface | Address       | Notes                                          |
|---------|-------------------|---------------|------------------------------------------------|
| WAN     | wan            | Label MAC     |  Stored MAC in factory + offset 4, label MAC is Stored MAC - 2   |
| LAN     | br-lan             | Label MAC+1   |              |
| 2.4GHz  | phy0-ap0          | Label MAC + 2     |             |
| 5GHz    | phy1-ap0          | Label MAC + 3     |              |

- 0x000000000000-0x000000100000 : "BL2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "Factory"
- 0x000000380000-0x000000580000 : "FIP"
- 0x000000580000-0x000003580000 : "ubi"
- 0x000003580000-0x000006580000 : "ubi1"
- 0x000006580000-0x0000065a0000 : "Product"
- 0x0000065a0000-0x000007580000 : "Custom"

- The original partition-Ubi partition-Ubi1 is an AB dual system, and Openwrt only uses Ubi. So flash requires modifying the uboot variable `boot_from=ubi` to ensure that it only starts from Ubi.

- The Product and Custom partitions are original and only exist to align with the original layout; they are not used by OpenWrt.

- id: 0, kernel
- id: 1, rootfs
- id: 2, rootfs_data

- **USB-to-TTL Serial Adapter** (e.g., CH340 or CP2102).
- **Dupont Wires** (male-to-male, 3 wires).
- **PC/Laptop** with a serial communication tool.
- Screwdriver (to open the router case).

1. **OpenWrt Firmware**:
   - Download the appropriate `wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin` firmware file for your router from the [OpenWrt website](https://openwrt.org/).
2. **Serial Communication Tool**:
   - Windows: PuTTY, Tera Term.
   - Linux/Mac: Minicom, screen.
3. (Optional) **TFTP Server**:
   - Install a TFTP server like Tftpd64 or tftp-hpa.

---

1. Open the router casing and locate the **TX, RX, and GND** pins.
2. Connect the router pins to the USB-to-TTL adapter as follows:
   - **TX (router)** → **RX (adapter)**
   - **RX (router)** → **TX (adapter)**
   - **GND (router)** → **GND (adapter)**
3. Do **not** connect the VCC pin to avoid damage.

- **Baud rate**: 115200
- **Data bits**: 8
- **Stop bits**: 1
- **Parity**: None
- **Flow control**: None

---

1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***

    1. Factory mode
    2. Startup system (Default)
    3. Upgrade firmware
    4. Upgrade ATF BL2
    5. Upgrade ATF FIP
    6. Upgrade single image
    7. Load image
    0. U-Boot console

Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Select Option 0 by typing 0 and pressing Enter.
5. Input into
```plaintext
MT7981> setenv boot_from ubi
MT7981> saveenv
Saving Environment to MTD... Erasing on MTD device 'nmbm0'... OK
Writing to MTD device 'nmbm0'... OK
OK
MT7981> printenv
baudrate=115200
boot_from=ubi
...
```
the above indicates system will start from *ubi*.
and then type
```plaintext
MT7981> reset
```
will boot from *ubi*

1. Power on the router and observe the serial terminal output.
2. When prompted (e.g., `Hit any key to stop autoboot: 3`), press the '/' key quickly to interrupt the boot process.
3. You will see the U-Boot Boot Menu:
```plaintext
*** U-Boot Boot Menu ***

    1. Factory mode
    2. Startup system (Default)
    3. Upgrade firmware
    4. Upgrade ATF BL2
    5. Upgrade ATF FIP
    6. Upgrade single image
    7. Load image
    0. U-Boot console

Press UP/DOWN to move, ENTER to select, ESC/CTRL+C to quit
```
4. Choose Option 3: Upgrade Firmware
Enter Upgrade Mode
Select Option 3 by typing 3 and pressing Enter.
Upgrade Methods
You will be prompted to choose between:
```plaintext
*** Upgrading Firmware ***

Run image after upgrading? (Y/n): y

Available load methods:
    0 - TFTP client (Default)
    1 - Xmodem
    2 - Ymodem
    3 - Kermit
    4 - S-Record
    5 - RAM

Select (enter for default): 0

Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.10
Input IP netmask: 255.255.255.0
Input file name: wr3000k-<build_time>-mediatek-filogic-tenbay_wr3000k-squashfs-sysupgrade.bin
```
Type Enter to proceed. The router will erase the old firmware and write the new one.

Signed-off-by: Jianyu Zhuang <xzjianyu@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-22 18:45:01 +01:00
Maxim Anisimov
6992d6e51a mediatek/filogic: add support for Cudy AP3000 v1
Hardware:
  SoC:     MT7981b
  RAM:     512 MB
  Flash:   256 MB SPI NAND
  Ethernet:
    1x2.5Gbps (rtl8221b)
  WiFi:    2x2 MT7981
  Button:  Reset
  LED:     1x multicolor

Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-22 18:38:16 +01:00
Tianling Shen
5a7fb834c7 mediatek: update openembed som7981 support
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).

Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio

Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.

Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-22 18:19:16 +01:00
Jonas Jelonek
cd8dcfef37 mediatek: filogic: bpi-r4: set netdev-name for sfp ports
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
2024-12-20 18:19:10 +01:00
Jonas Jelonek
84fc59c0d5 mediatek: filogic: bpi-r3: set netdev-name for sfp1 port
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
2024-12-20 18:19:10 +01:00
Jonas Jelonek
d4d6c48b6e mediatek: filogic: support openwrt,netdev-name for renaming interfaces
Add support in filogic subtarget for our own custom property
`openwrt,netdev-name` in the device tree instead of `label` for
renaming interfaces. This was suggested upstream to avoid potential
conflicts [1].

[1] https://lore.kernel.org/netdev/20240709124503.pubki5nwjfbedhhy@skbuf/

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
2024-12-20 18:19:09 +01:00
Yaoguang Bai
6b32a5d768 mediatek: filogic: add support for NRadio C8-668GL
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.

- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
  - 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
  - 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
  - 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector

The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:

| Vendor  | OpenWrt Interface | Address       | Notes                                          |
|---------|-------------------|---------------|------------------------------------------------|
| LAN     | br-lan            | Label MAC     | Default                                        |
| WAN     | lan4              | Label MAC+1   | Only when lan4 is switched to WAN             |
| 2.4GHz  | phy0-ap0          | Label MAC     |                                                |
| 5GHz    | phy1-ap0          | Label MAC     | (Local Admin bit set)                         |
| Modem   | eth1              | Label MAC+2   |                                                |

1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
   - Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.

Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```

Power off the router, hold the **WPS button**, and power it back on.

1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.

- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
  ```bash
  cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
  ```

Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
2024-12-13 15:29:04 +01:00
Hauke Mehrtens
f8b93e2d12 mediatek: filogic: Migrate wifi configuration device paths
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.

This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate

Fixes: 0ef9274721 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-10 00:02:27 +01:00
Maxim Anisimov
d087a79b7b mediatek/filogic: add Keenetic KN-3811 support
Specification:
 * Mediatek MT7981BA
 * 256 MB SPI-NAND
 * 512 MB DDR4 RAM
 * MT7976CN DBDC AX Wi-Fi
 * MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
 * 4x LED (power, internet, fn, wifi)
 * 3x buttons (wps, fn, reset)
 * 1x USB 3.0 port

Serial Interface:
 * 3 Pins GND, RX, TX
 * Settings: 115200, 8N1

Notes:
 * The device supports dual boot mode
 * Fn led reassigned to wlan 2.4

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
   to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
   the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-08 19:52:35 +01:00
John Crispin
5c12fe45b9 target/metadata: set OpenWrt One as the default menuconfig target/profile
Signed-off-by: John Crispin <john@phrozen.org>
2024-12-02 13:55:36 +01:00
John Crispin
f342255025 mediatek: filogic: enable CONFIG_LEDS_TRIGGER_PATTERN
The boot LED on OpenWrt One is PWM driven and sets the pattern trigger as the
default inside its devicetree.

Signed-off-by: John Crispin <john@phrozen.org>
2024-12-02 13:55:36 +01:00
Mikhail Zhilkin
ee8df790ca mediatek: MERCUSYS MR90X v1: add OpenWrt U-Boot (UBI) layout
This commit adds OpenWrt U-Boot (UBI) layout support for MERCUSYS MR90X
v1.

Stock U-Boot UBI size:   50 MiB
OpenWrt U-boot UBI size: 126 MiB

Install
-------
1. Perform steps 1-14 of the OpenWrt installation guide (use OpenWrt
   initramfs-recovery.itb instead of initramfs-kernel.bin at the step 10,
   12 and 14).
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation

2. Make backups:
```
cat /dev/mtd0 > /tmp/boot.bin
cat /dev/mtd5 > /tmp/tp_data.bin
```
   Copy /tp_data dir content, /tmp/boot.bin and /tmp/tp_data.bin and to
   your PC using scp. You can also backup the remaining partititons. Copy
   backups to a safe place, they are required for the next steps and stock
   firmware recovery.

3. Reboot to OpenWrt initramfs:
```
reboot
```

4. Copy OpenWrt ubi-bl31-uboot.fip, ubi-preloader.bin,
   ubi-squashfs-sysupgrade.itb and MT7986_EEPROM.bin, default-mac (from
   /tp_data backup) to the /tmp folder of the router using scp.

5. Prepare UBI:
```
ubidetach -p /dev/mtd3; ubiformat /dev/mtd3 -y; ubiattach -p /dev/mtd3
ubimkvol /dev/ubi0 -N fip -t static -s 1MiB
ubiupdatevol /dev/ubi0_0 /tmp/ubi-bl31-uboot.fip
ubimkvol /dev/ubi0 -N ubootenv -s 0x1f000
ubimkvol /dev/ubi0 -N ubootenv2 -s 0x1f000
```

6.  Install kmod-mtd-rw and unlock partitions:
```
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock boot
mtd unlock bl2
mtd unlock factory
```

7. Prepare "factory" partition:
```
dd if=/dev/zero bs=$((0x8000)) count=1 | tr '\000' '\377' > /tmp/factory.bin
dd if=/tmp/MT7986_EEPROM.bin of=/tmp/factory.bin conv=notrunc
dd if=/tmp/default-mac >> /tmp/factory.bin
```

8. Write "factory" partition:
```
mtd erase factory
mtd write /tmp/factory.bin factory
```

9. Write preloader partition:
```
mtd erase bl2
mtd write /tmp/ubi-preloader.bin bl2
```

10. Write OpenWrt sysupgrade image:
```
sysupgrade -n /tmp/ubi-squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connetion if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Link: https://openwrt.org/toh/mercusys/mr90x_v1#serial

Return to stock:
----------------
1. Copy "boot" partition backup (boot.bin) to the /tmp dir of the router
   using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot:
```
   insmod mtd-rw i_want_a_brick=1
   mtd unlock boot
   mtd erase boot
   mtd write /tmp/boot.bin boot
```

4. Erase UBI and reboot:
```
mtd erase ubi
reboot
```

5. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1

6. Complete steps 1-9 of the OpenWrt installation guide to get root
   rights.
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation

7. Upload "tp_data" partition backup (tp_data.bin) to the /tmp folder of
   the router using scp.

8. Restore stock calibrations:
```
mtd write /tmp/tp_data.bin tp_data
reboot
```

9. Perform "factory restore" via stock firmware web interface.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-30 18:36:05 +01:00
Maxim Anisimov
5a4eb56a7b mediatek/filogic: add Keenetic KN-3911 support
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 512MB RAM
 - 128MB SPI NAND
 - 2 LEDs (green, orange)
 - 3 buttons (fn, reset, wps)
 - 2 2.5Gbit ethernet ports based on Airoha EN8811H phy

Serial Interface:
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

Notes:
 - The device supports dual boot mode

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3911-squashfs-factory.bin"
   to "KN-3911_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
   the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-28 22:33:21 +01:00
Maxim Anisimov
0d651dd302 mediatek/filogic: enable mtd virtual concat support
This is required for upcoming Keenetic KN-3911 support

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-28 22:33:21 +01:00
Mikhail Zhilkin
d413163832 mediatek: Routerich AX3000: add OpenWrt U-Boot layout
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.

Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
   /tmp folder of the router using scp.

2. Make mtd partitions backups:
   http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
   contents

3. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

4. Write FIP and preloader:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/ubootmod-preloader.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```

5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
   with IP 192.168.1.254.

6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.

7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
   router using scp.

8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot

Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
   router using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot and reboot:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/BL2.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/FIP.bin FIP
reboot
```

4. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-24 23:41:02 +01:00
David Ignjic
faf4b3e0f7 mediatek: filogic: add support for Cudy WR3000S v1
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V

MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot  shell.

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.88. Rename the image to "cudy3000s.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000

5. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Signed-off-by: David Ignjic <ignjic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 20:24:57 +01:00
George Oldfort
2898d1d126 mediatek: add support for Acer Predator W6d and Acer Vero W6m
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).

The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.

Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.

This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
George Oldfort
e7aaba2587 mediatek: make use of Acer Predator Connect W6's u-boot environment
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh

The idea and the implementation were thankfully taken from PR #16410.

This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
Romanov Danila
d8a9669093 mediatek: change Routerich AX3000 ubi size
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)

These partitions weren't used:
firmware_backup
zrsave
config2

Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 15:42:24 +01:00
Rosen Penev
cd92cbddf8 kernel: filter out compiler opts from config
These get dynamically set based on compiler version. Not relevant for
targets.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-17 14:55:16 +01:00
Rosen Penev
da8abd4a1e kernel: remove GCC11_NO_ARRAY_BOUNDS
This symbol is no longer present.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-17 14:55:16 +01:00
Enrico Mioso
b43194e041 mediatek: filogic: add support for GatoNetworks GDSP
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.

Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
          the built-in Mediatek watchdog is also present and effective, but
          not used at the moment.

This porting has been tested only with 1x 5G modems installed (the device
supports up to two).

Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.

OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:

insmod mtd-rw i_want_a_brick=1

Then update relevant flash partitions:

mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP

And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.

Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).

U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.

MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.

device					MAC address		U-Boot env variable		factory partition offset
2.4 GHz Wi-Fi		:84						wifi_mac							0x4
5.8 GHz Wi-Fi		:85						not present						not present
WAN							:86						wan_mac								0x24
LAN							:87						lan_mac								0x2A

Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2024-11-14 04:14:23 +00:00
John Crispin
48028cd102 mediatek: set 7 MACs per wifi band in board.json on OpenWrt One
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-05 10:11:44 +01:00
John Crispin
a85f11f191 mediatek: filogic: add Arcadyan Mozart platform
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 4 GiB DDR4 RAM
* 2x 10000M + 1x 1000M  ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* 2 buttons (Reset, WPS)
* 2x LED for each GMAC
* USB-C PD power input

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-01 07:43:00 +01:00
John Crispin
cfe8e6e75f mediatek: add support for Realtek RTL8261n 10G PHYs
There is no upstream driver yet. Merge the RTL SDK driver for now.

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-01 07:43:00 +01:00
Daniel Golle
dbc2923cbe mediatek: filogic: convert Acer Predator W6 to use NVMEM framework
Read WiFi calibration data via NVMEM framework. The MAC addresses are
stored inside a file on a filesystem and hence still have to be
extracted in userspace.

WiFI EEPROM extraction has already accidentally been partially removed
by commit 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran
devices").

Fixes: 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-18 12:38:21 +01:00
Chukun Pan
e98987048a mediatek: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-10-15 21:36:16 +01:00
Chukun Pan
5fd4743d4c mediatek: filogic: fix network config for mt7986b-rfb
Fix the network configuration according to the device tree.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-10-15 21:36:16 +01:00
Daniel Golle
3e6de5d77a mediatek: use NVMEM framework on all Adtran devices
Use NVMEM framework to assign MAC addresses and WiFi EEPROM data on
all Adtran SmartRG devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-15 17:56:06 +01:00
Daniel Golle
175bd80349 mediatek: add driver for Adtran MFGINFO NVMEM layout
This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-15 17:55:05 +01:00
Daniel Golle
d0a2b3f824 mediatek: add Adtran SmartRG SDG-8733A
Specification is similar to other devices of the MT Stuart series:
 * Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
 * 8 GiB eMMC
 * 2 GiB DDR4 RAM
 * 2500M/1000M/100M LAN port
 * 10000M/5000M/2500M/1000M/100M/10M WAN port
 * MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
 * Renesas DA14531MOD Bluetooth
 * 2 buttons (Reset, Mesh/WPS)
 * uC-controlled RGB LED via I2C
 * 2x LED for the 2.5G port, 3x LED for the 10G port
 * 3.3V-level 115200 baud UART console via 4-pin Dupont connector
   exposed at the bottom of the device
 * USB-C PD power input

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-20 22:47:05 +01:00
Daniel Golle
72d88af43f mediatek: filogic: fix WiFi MAC address retrieval for Adtran SDG-8734
Fix a typo in the MAC address assignment script affecting SDG-8734.

Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-19 14:37:56 +01:00
Daniel Golle
5fa86a4e2b mediatek: mt7988a-rfb: align order of SFPs with SDK build
MediaTek SDK uses eth2 as additional LAN port and eth1 as WAN.
Do the same also in OpenWrt to keep settings aligned with the SDK.

Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-09-02 10:14:20 +02:00
Daniel Golle
dd1bfbe971 mediatek: phase out uImage.FIT partition parser
All boards using the deprecated uImage.FIT partition parser have
been migrated to the new fitblk driver. Drop the now no longer
needed partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:52 +01:00
Daniel Golle
688239d91e mediatek: filogic: convert Zyxel EX5601-T0 to fitblk
Use fitblk driver instead of deprecated partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Daniel Golle
ca4f5b0def mediatek: filogic: convert Netcore N60 to fitblk
Use fitblk driver instead of deprecated partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Daniel Golle
d657ca6760 mediatek: filogic: convert Xiaomi WR30U to fitblk
Use fitblk driver instead of deprecated partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Daniel Golle
c29ab486a8 mediatek: filogic: convert Xiaomi AX3000T to fitblk
Use fitblk driver instead of deprecated partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Daniel Golle
ee7aacb3e7 mediatek: filogic: convert Qihoo 360T7 to fitblk
Use fitblk driver instead of deprecated partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Daniel Golle
609f29da62 mediatek: filogic: convert JCG Q30 PRO to fitblk
Use fitblk driver instead of deprecated partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Daniel Golle
52ef01672c mediatek: filogic: convert H3C Magic NX30 Pro to fitblk
Use fitblk driver instead of deprecated partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Daniel Golle
ffd5cca73e mediatek: filogic: convert MT7981 RFB to fitblk
Use fitblk driver instead of deprecated uImage.FIT partition parser.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-28 15:11:51 +01:00
Pawel Dembicki
19d770d7b9 mediatek: filogic: add support for Cudy AP3000 Outdoor
Hardware highlights:
  - MediaTek MT7981 WiSoC
  - 256MB DDR3 RAM
  - 64MB SPI-NAND
  - MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
  - 1x LED in two colors
  - 2x Button
  - 1x 1GbE
  - Two detachable antenas, two internal pcb antenas
  - PoE powered (standalone)

MAC:
LAN MAC: label mac
2.4G MAC: label mac -1
5G MAC: label mac

How to install:
1. Apply Cudy Intermediate OpenWrt image for AP3000 Outdoor V1
2. Install OpenWrt sysupgrade image

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16156
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-08-25 15:35:53 +02:00
Daniel Golle
1069514978 mediatek: backport pending Ethernet PHY driver patches
Use pending patchset for 2.5GE PHY driver, unifying LED handling
accross all MediaTek Ethernet PHYs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-08-22 00:20:02 +01:00
Chukun Pan
73832e1a48 mediatek: add support for TP-Link TL-XTR8488
Hardware specification:
  SoC: MediaTek MT7986A 4x A53
  Flash: ESMT F50L1G41LB 128MB
  RAM: MT40A512M16TB-062ER 1GB
  Ethernet: 2x 2.5G, 4x 1G Lan
  WiFi1: MT7976GN 2.4GHz 4T4R
  WiFi2: MT7976AN 5.2GHz 4T4R
  WiFi3: MT7915AN 5.8GHz 4T4R
  Button: Reset, WPS, Turbo
  USB: 1 x USB 3.0
  Power: DC 12V 5A

Flash instructions:
  1. Execute the following operation to open nc shell:
     https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
  2. Replace the stock bootloader to OpenWrt's:
     dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
     dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
  3. Connect to your PC via the Gigabit port of the router,
     set a static ip on the ethernet interface of your PC.
  4. Download the initramfs image, and restart the router,
     waiting for tftp recovery to complete.
  5. After openwrt boots up, perform sysupgrade.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15930
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-25 22:54:16 +02:00
Tianling Shen
f2f428c699 mediatek: add ABT ASR3000 support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, Mesh
  Power: DC 12V 1A

Gain telnet access:
1. Login into web interface, and download the configuration.
2. Decode and uncompress the configuration:
     * Enter fakeroot if you are not login as root.
   base64 -d e-xxxxxxxxxxxx-cfg.tar.gz | tar -zx
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
   ( sleep 3s; /usr/sbin/telnetd; ) &
5. Repack the configuration:
   tar -zc etc/ | base64 > e-xxxxxxxxxxxx-cfg.tar.gz
6. Upload new configuration via web interface, now you can connect to
   ASR3000 via telnet.

Flash instructions:
1. Connect to ASR3000, backup everything, especially 'Factory' part.
2. Write new BL2:
   mtd write openwrt-mediatek-filogic-abt_asr3000-preloader.bin BL2
3. Write new FIP:
   mtd write openwrt-mediatek-filogic-abt_asr3000-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15887
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-07-21 16:13:06 +02:00
Tianling Shen
39c824f846 mediatek: switch to fitblk for cmcc rax3000m
Use the new fitblk driver.

Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-07-18 13:20:58 +01:00
Tianling Shen
eb510d2158 mediatek: convert eeprom/macaddr to nvmem format for cmcc rax3000m
Switch to new nvmem binding.

Also fixes a issue that the MAC address assigned to lan/wan was
reversed on eMMC boards.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-07-18 13:20:58 +01:00
Daniel Golle
b39375ae4c mediatek: fix platform_copy_config()
Also use env variables exported by export_fitblk_rootdev() in
platform_copy_config().

Fixes: 4448d6325f ("mediatek: make use of common uImage.FIT upgrade functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-07-18 13:05:46 +01:00
Daniel Golle
4448d6325f mediatek: make use of common uImage.FIT upgrade functions
Use newly introduced fit_do_upgrade() function in /lib/upgrade/platform.sh.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-07-18 11:48:53 +01:00