Commit Graph

30244 Commits

Author SHA1 Message Date
Luis Mita
d780d530dd ramips: mt76x8: sync Cudy TR1200 v1 naming
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-06-10 10:13:56 +02:00
Tianling Shen
0397932fdd mediatek: convert eeprom/macaddr to nvmem format for jdcloud re-cp-03
Switch to new nvmem binding.

Also fixes a issue that the MAC address assigned to lan/wan was reversed.

Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-06-10 10:08:19 +02:00
Sijia Huang
33db914607 mediatek: filogic: Add support for Wavlink WL-WN586X3
Hardware
--------
- SOC: MediaTek MT7981
- ram: 256MB DDR3
- FLASH: 16MB SPI-NOR
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS

MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
 2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label
 5G: 80:3F:5D:xx:xx:x3 Same as 2G

Installation Method 1: ssh
--------------------------
1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if
   required.
2. Navigate to http://192.168.10.1/
3. Log into the Wavlink WebGUI. Default username/password is
   admin/admin.
4. Use WebGUI to upgrade the firmware to
   WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin
   downloaded from
   https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
   Warning: All settings will be lost!
5. Wait about 5 minutes, and after flashing is completed, log into
   the router using (with admin123 as password):
   ssh root@192.168.10.1
6. scp the openwrt image file onto the router, usually under /tmp
   somewhere.
   openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin
7. Flash openwrt image file like so:
   mtd write \
     openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \
     firmware
   Warning: Previous firmware will be overwritten!
8. Wait about 5 minutes, and after the flashing is completed, set
   the PC IP to 192.168.1.100 if required and log into the router
   like so:
   ssh root@192.168.1.1

Installation Method 2: u-boot
-----------------------------
1. Connect UART:  TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND.
2. Connect PC to the wan (not lan!) port.
3. Setup the tftp server on PC, set IP to 192.168.10.100,
4. Power on the device. Select '2' to upgrade firmware in Uboot.
5. Input the image name and start to upgrade.

Uboot console log:

CPU:   MediaTek MT7981
Model: mt7981-rfb
DRAM:  256 MiB
Core:  34 devices, 13 uclasses, devicetree: embed
Loading Environment from nowhere... OK
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address -
02:47:fb:b2:53:2d
eth0: ethernet@15100000
UBOOT WN586X3A
gpio: pin 9 (gpio 9) value is 0
gpio: pin 10 (gpio 10) value is 0
gpio: pin 5 (gpio 5) value is 0
gpio: pin 12 (gpio 12) value is 0
gpio: pin 13 (gpio 13) value is 0

  *** U-Boot Boot Menu ***

      1. Startup system (Default)
      2. Upgrade firmware
      3. Upgrade ATF BL2
      4. Upgrade ATF FIP
      5. Upgrade single image
      6. Load image
      0. U-Boot console

Co-authored-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: Sijia Huang <engineer31@win-star.com>
2024-06-09 14:58:25 +02:00
Rosen Penev
dd6bbbabd3 ath79: 8dev: remove wmac userspace handling
Before the nvmem rework, this was already handled in dts with
mtd-cal-data instead of qca,no-eeprom. No need to duplicate. Also, the
800 size value seems nonsensical. 440 is the standard.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-06-09 12:24:15 +02:00
Rosen Penev
74f2df9dbc ath79: mtd-cal-data removals
Replacement can be done with nvmem.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-06-09 12:24:15 +02:00
Rosen Penev
79fc4dba60 ath79: convert pcs,cap324 calibration to nvmem
Userspace handling is deprecated.

Also fix a bug with userspace handling where the wrong calibration data
was being used for the PCI card. The dts was correct but userspace was
not.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-06-09 12:24:15 +02:00
Rosen Penev
6483615580 ath79: cd-e380ac-v2: remove duplicate eth0
It seems in the transition to nvmem, eth0 was specified twice and was
already converted to use nvmem.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-06-09 12:24:15 +02:00
Rosen Penev
85c5c9aa68 ath79: remove unused dts labels
These are not referenced.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-06-09 12:24:15 +02:00
Rosen Penev
ff5e8476d9 ath79: fix dtc address warnings
These should match reg values.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2024-06-09 12:24:15 +02:00
Shiji Yang
2d00ed7caa kernel: trim outdated kernel config symbols
These symbols have already been removed from the upstream Linux source
code. They are automatically compared and removed by a kernel config
scanning script[1].

[1] https://github.com/openwrt/openwrt/pull/15324

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-06-09 11:45:34 +02:00
Martin Schiller
6ec7711d00 lantiq: Refresh patches and configuration for linux 6.6
Make all the patches apply. This also refreshes some of the kernel
configurations.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-06-08 23:25:35 +02:00
Martin Schiller
c80fa584e5 lantiq: set Linux 6.6 as testing kernel
Add KERNEL_TESTING_PATCHVER for Linux 6.6.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-06-08 23:25:35 +02:00
Martin Schiller
5b522e4969 kernel/lantiq: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-06-08 23:25:35 +02:00
Martin Schiller
e85c80edcb kernel/lantiq: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-06-08 23:25:35 +02:00
David Bauer
c2a5cd110c mpc85xx: only build zImage on required targets
Make the OF-compatible zImage per-board selectable. This allows the
image to only be built with the wrapper if the target actually uses it.

This fixes build-failures for the mpc85xx-p2020 subtarget.

Fixes: 557c094f0579 ("mpc85xx: only build zImage on required targets")

Signed-off-by: David Bauer <mail@david-bauer.net>
2024-06-08 17:30:20 +02:00
Mieczyslaw Nalewaj
df28fe4b59 kernel: rtl8367b: remove unnecessary cpu_port setting
Set the appropriate cpu_port value based on the use of realtek,extif0 to extif2
instead of the additional cpu_port parameter.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-08 16:28:37 +02:00
Mieczyslaw Nalewaj
c1a26de1c6 kernel: rtl8367: set the correct cpu_port value
Set the appropriate cpu_port value based on the use of realtek,extif0 or realtek,extif1 parameter.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-08 16:28:36 +02:00
Zxl hhyccc
2d6cedab27 kernel: bump 6.1 to 6.1.92
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.92

Removed upstreamed:
 bcm27xx/patches-6.1/950-0270-net-bcmgenet-Reset-RBUF-on-first-open.patch
 generic/backport-6.1/600-v6.9-03-net-gro-add-flush-check-in-udp_gro_receive_segment.patch
 generic/pending-6.1/681-net-bridge-fix-multicast-to-unicast-with-fraglist-GS.patch
 generic/pending-6.1/682-net-core-reject-skb_copy-_expand-for-fraglist-GSO-sk.patch
 generic/pending-6.1/684-net-bridge-fix-corrupted-ethernet-header-on-multicas.patch
 generic/pending-6.1/778-net-l2tp-drop-flow-hash-on-forward.patch
 imx/patches-6.1/002-6.2-phy-freescale-imx8m-pcie-Refine-i.MX8MM-PCIe-PHY-dri.patch

All other patches automatically rebased.

Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
2024-06-08 14:16:19 +02:00
David Bauer
de59fc4540 ipq40xx: fix broken image generation for EX6150v2
All NETGEAR EX6150v2 validate the rootfs for which OpenWrt places a
fakeheader at the position, where the bootloader expects it.

Some EX6150v2 bootloaders do however make a broken assumption about
where the rootfs starts. This is due to them calculating the rootfs
start not based upon the kernel-length but the string-offset of the
FIT-image.

We have to be compatible with both this broken as well as the valid
calculation. So we do relocate the FDT string section to a
block-boundary and enlarge the FIT image to end at this boundary +
BLOCKSIZE / 2. This way, both the broken as well as correct calculations
do expect the rootfs-header at the same position.

It is worth noting, that this is a rare edge-case in which only happens
if the image-length as well as the start of the string-section are not
placed in the same erase-block. This is an edge-case which happens very
rarely (thus it was not spotted prior).

Affected:
 - U-Boot 2012.07 (Jun 16 2016 - 11:59:37)

Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8f9546f7b0a14f3afa813e39ed45c968ece24464)
2024-06-08 02:09:15 +02:00
Linus Walleij
884bef5d1b kirkwood: Add Marvell RTC to two devices
The recently added D-Link DNS-320L and the Zyxel NSA310S
is missing an RTC module so let's give them the default
Marvell RTC at least.

Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-06-07 21:48:42 +02:00
Tianling Shen
4edde98768 mediatek: fix wps button for nokia ea0326gmp
The gpio is actually low active, fix it.

Fixes: 40e7fab9e4 ("mediatek: add Nokia EA0326GMP support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15651
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-07 14:19:39 +02:00
Tim Harvey
0520c45f2f imx: 6.6: update kernel config
added some missing configs needed when building 6.6 with all kmods

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2024-06-06 22:04:23 +02:00
Tim Harvey
c78c71737b imx: 6.6: refresh kernel patches
refresh 6.6 kernel patches via 'make target/linux/refresh'

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2024-06-06 22:04:23 +02:00
Tim Harvey
a6d4d369eb imx: add 6.6 kernel as testing
allow to test 6.6 kernel for imx

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2024-06-06 22:04:23 +02:00
Tim Harvey
368cd88c44 imx: fix cortexa9/cortexa7 image builds due to dts move
The IMX device-tree's for arm moved from arch/arm/boot/dts to
arch/arm/boot/dts/nxp/imx. Use that if using the 6.6 kernel.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2024-06-06 22:04:23 +02:00
Tim Harvey
7dfdfac344 imx: copy config from 6.1 to 6.6
Copy the 6.1 config to 6.6

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2024-06-06 22:04:23 +02:00
Tim Harvey
e4d76cf6ae imx: copy patches from 6.1 to 6.6
copy 6.1 patches to 6.6 and fixup:
 - removed patches already upstream
 - adapted pathnames of dts patches for new kernel

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2024-06-06 22:04:23 +02:00
Daniel Golle
56bce303ce generic: 6.6: refresh patches
Patch 733-01-net-ethernet-mtk_eth_soc-use-napi_build_skb.patch needs
a refresh as line numbers no longer match.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-06-06 20:08:13 +01:00
Tianling Shen
a568540fd4 mediatek: filogic: move nand-only devices out of bootdev detection
For the first-time installation (mostly migrates from vendor firmware)
the ubiblock is not ready, but bootdev detection relies on it. This
means users must create ubiblock manually otherwise the sysupgrade
will not work.

Now a unique case is added for nand devices which use new fit format,
let's move to it.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-06-06 18:56:32 +01:00
Tianling Shen
40e7fab9e4 mediatek: add Nokia EA0326GMP support
Hardware specification:
  SoC: MediaTek MT7981B 2x A53
  Flash: 128 MB SPI-NAND
  RAM: 256MB
  Ethernet: 4x 10/100/1000 Mbps
  Switch: MediaTek MT7531AE
  WiFi: MediaTek MT7976C
  Button: Reset, WPS/Mesh
  Power: DC 12V 1A

Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
   https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
     These binaries are extraced from the factory firmware, which are
     dynamically linked with aarch64 musl 1.1.24. To use them, you
     must run them under the same runtime environment, otherwise the
     binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
   tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
   mv mkconfig seama /bin
   chmod +x /bin/mkconfig
   chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
     Enter fakeroot if you are not login as root.
   mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
   tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
   tar -zcf backup.tar.gz etc/
   mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.

A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz

Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
   mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
   mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
   IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-06-06 18:56:32 +01:00
Felix Fietkau
f352ca5a8a kernel: use napi_build_skb in mtk_eth_soc
Improves performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-06-06 11:47:59 +02:00
Robert Marko
458cafd0d0 generic: routerbootpart: fix compilation on 64-bit
Trying to compile routerbootpart parsers on 64-bit platforms will fail:
drivers/mtd/parsers/routerbootpart.c: In function 'routerboot_find_dynparts':
./include/linux/kern_levels.h:5:25: error: format '%X' expects argument of type 'unsigned int', but argument 3 has type 'size_t' {aka 'long unsigned int'} [-Werror=format=]
    5 | #define KERN_SOH        "\001"          /* ASCII Start Of Header */
      |                         ^~~~~~
./include/linux/printk.h:427:25: note: in definition of macro 'printk_index_wrap'
  427 |                 _p_func(_fmt, ##__VA_ARGS__);                           \
      |                         ^~~~
./include/linux/printk.h:498:9: note: in expansion of macro 'printk'
  498 |         printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
      |         ^~~~~~
./include/linux/kern_levels.h:11:25: note: in expansion of macro 'KERN_SOH'
   11 | #define KERN_ERR        KERN_SOH "3"    /* error conditions */
      |                         ^~~~~~~~
./include/linux/printk.h:498:16: note: in expansion of macro 'KERN_ERR'
  498 |         printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
      |                ^~~~~~~~
drivers/mtd/parsers/routerbootpart.c:170:25: note: in expansion of macro 'pr_err'
  170 |                         pr_err("%s: mtd_read error while parsing (offset: 0x%X): %d\n",

So, lets simply add the length modifier 'z' to fix compilation.

Link: https://github.com/openwrt/openwrt/pull/15640
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-06 11:45:03 +02:00
Daniel Golle
84a527417d mediatek: improve reliability of Fidelix/Dosilicon SPI-NAND
Prior to performing a PROGRAM LOAD RANDOM DATA operation, a WRITE
ENABLE (06h) command must be issued to change the contents of the
memory array. Following a WRITE ENABLE (06) command, **first a PROGRAM
LOAD (02h or 32h) command must be issued to reset the cache**, then
issue a PROGRAM LOAD RANDOM DATA (84h or 34h) command

This is dirty fix provided to use by MediaTek engineer Sky Huang which
may resolve the "OpenWrt Kiss of Death" issue we've been seeing on the
Linksys E8450 aka. Belkin RT3200. However, it means that everything has
to be re-written with that patch already applied, ie. we need to rebuild
the installer once it is part of snapshot builds to have any effect.

Users already on FIP-in-UBI layout are advised to re-write 'fip' UBI
volume and 'bl2' MTD partition manually once from within Linux after
this fix has been applied.

A similar fix will also be required for U-Boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-06-05 21:05:52 +01:00
INAGAKI Hiroshi
1fbfc251c9 ramips: add support for Buffalo WSR-2533DHPL2
Buffalo WSR-2533DHPL2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MediaTek MT7621A.

Specification:

- SoC           : MediaTek MT7621AT
- RAM           : DDR3 128 MiB (Winbond W631GG6MB12J)
- Flash         : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN          : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet      : 10/100/1000 Mbps x4
  - Switch      : MediaTek MT7530 (SoC)
- LED/keys      : 8x/6x (2x buttons, 1x slide-switch)
- UART          : through-hole on PCB (J4)
  - arrangement : 3.3V, GND, TX, RX from triangle-mark
  - settings    : 57600n8
- Power         : 12VDC 1.5A

Flash instruction using factory.bin image:

1. boot WSR-2533DHPL2 normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
   firmware update page
   ("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
   button
   Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing

Flash instruction using initramfs image:

1. prepare the TFTP server with the initramfs image renamed to
   "linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL2
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL2 downloads
   the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
   device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing

Notes:

- There are 2x factory*.bin images for different purposes.

  - factory.bin      : for flashing on OEM WebUI
  - factory-uboot.bin: for flashing on OEM bootloader or initramfs image

  factory-uboot.bin is useful for recoverying the device, or refreshing
  when the kernel partition is expanded in the future. sysupgrade on
  this device accepts factory-uboot.bin with option "-F", but on that
  situation, user configurations won't be kept, so it's not for normal
  use.

MAC addresses:

LAN    : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
WAN    : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
2.4 GHz: 18:EC:E7:xx:xx:E1 (Factory, 0x4    (hex))
5 GHz  : 18:EC:E7:xx:xx:E4 (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-06-05 21:14:16 +02:00
INAGAKI Hiroshi
ea8d140b25 ramips: add support for Buffalo WSR-2533DHPLS
Buffalo WSR-2533DHPLS is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.

Very similar to Buffalo WSR-2533DHPL, but with NAND, different GPIO
and TRX partitions.

Specification:

- SoC           : MediaTek MT7621AT
- RAM           : DDR3 256 MiB (Samsung K4B2G1646F-BYMA)
- Flash         : RAW-NAND 128 MiB
                  (Winbond W29N01HV or KIOXIA TC58BVG0S3HTAI0)
- WLAN          : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet      : 10/100/1000 Mbps
  - Switch      : MediaTek MT7530 (SoC) 4 ports
- LED/keys      : 8x/6x (2x buttons, 1x slide-switch)
- UART          : through-hole on PCB (J4)
  - arrangement : 3.3V, GND, TX, RX from triangle-mark
  - settings    : 115200n8
- Power         : 12VDC 1.5A

Flash instruction using factory.bin image:

1. boot WSR-2533DHPLS normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
   firmware update page
   ("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
   button
   Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing

Flash instruction using initramfs image:

1. prepare the TFTP server with the initramfs image renamed to
   "linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPLS
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPLS downloads
   the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
   device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing

Notes:

- The embedded addresses in eeprom data in Factory partition have
  Buffalo's OUI, but they don't match with the actual addresses
  assigned to wlan devices. So fixup addresses by the user-space
  script.

  root@localhost:/# hexdump -C /dev/mtdblock3 | grep "^0000[08]000\s"
  00000000  15 76 a0 00 88 57 ee bc  01 a8 15 76 c3 14 00 80  |.v...W.....v....|
  00008000  15 76 a0 00 88 57 ee bc  01 f8 15 76 c3 14 00 80  |.v...W.....v....|

  See "MAC addresses" below for actual addresses.

- There are 2x factory*.bin images for different purposes.

  - factory.bin      : for flashing on OEM WebUI
  - factory-uboot.bin: for flashing on OEM bootloader or initramfs image

  factory-uboot.bin is useful for recoverying the device, or refreshing
  when the kernel partition is expanded in the future. sysupgrade on
  this device accepts factory-uboot.bin with option "-F", but on that
  situation, user configurations won't be kept, so it's not for normal
  use.

MAC addresses:

LAN    : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
WAN    : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
2.4 GHz: 90:96:F3:xx:xx:31
5 GHz  : 90:96:F3:xx:xx:38

[original work]
Signed-off-by: Audun-Marius Gangstø <audun@gangsto.org>
[convert to ubi, fix/improve DT, add sysupgrade support]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-06-05 21:14:16 +02:00
INAGAKI Hiroshi
d529ac5da8 ramips: mt7621: switch trx parser to parser_trx from mtdsplit
Switch trx parser to parser_trx of Linux Kernel from mtdsplit_trx to
split firmware partition using model-specific trx magic number on
some Buffalo devices.
This change is tested on Buffalo WSR-2533DHPL.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-06-05 21:14:16 +02:00
INAGAKI Hiroshi
47d9dcd01a build: move Build/buffalo-trx to image-commands.mk
Move Build/buffalo-trx to image-commands.mk from image/mt7622.mk to use
that definition from ramips as well.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-06-05 21:14:16 +02:00
Ashley Lee
3de3c2bdfa mediatek: add support for Ruijie RG-X60 Pro
This pull request ports Ruijie RG-X60 Pro router support to the main branch.

Parameters:
- SoC       : MediaTek MT7986A Quad-core ARM Cortex-A53 2.0GHz
- RAM       : DDR3 512MiB (W634GU6QB)
- Flash     : SPI-NAND 128 MiB (W25N01GVZEIG)
- WLAN      : MediaTek MT7986A integration dual-band WiFi 6
  - 2.4 GHz : b/g/n/ax, MIMO 4x4
  - 5 GHz   : a/n/ac/ax, MIMO 4x4
- Ethernet  : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
                    2500Mbps x 1 (Realtek RTL8221B-VB-CG)
- UART      : through-hole on PCB
  - [J500] GND, TX, RX, 3.3V (115200n1)
- Buttons   : Mesh, Reset
- LEDs      : 1x Power (Blue)
                  1x Turbo (Purple)
- Power     : 12 VDC, 3 A

How to Installation:
1. Remove the case and connect the TTL cable to the corresponding position.
2. Power on the device and quickly press "down" on the keyboard, then
   U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Openwrt image file name to be
   flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.

How return to stock:

1. Remove the case and connect the TTL cable to the corresponding
   position.
2. Power on the device and quickly press "down" on the keyboard, then
   U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Stock “E-WEBOS” image file name to
   be flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.

About recovery:
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.

About MAC Address:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 10:82:3D:XX:XX:9E | label     |
| LAN     | 10:82:3D:XX:XX:9F | label+1   |
| WLAN 2g | 10:82:3D:XX:XX:A0 | label+2   |
| WLAN 5g | 10:82:3D:XX:XX:A1 | label+3   |
+---------+-------------------+-----------+

Signed-off-by: Ashley Lee <code@emtips.net>
2024-06-05 17:44:11 +01:00
Michał Kępień
a60721f2ed mikrotik: switch to Yafut for building MikroTik NOR images
The Yafut tool now has limited capabilities for working on filesystem
images stored in regular files.  This enables preparing Yaffs2 images
for devices with NOR flash using upstream Yaffs2 filesystem code instead
of the custom kernel2minor tool.

Since minimizing the size of the resulting filesystem image size is
important and upstream Yaffs2 code requires two allocator reserve blocks
to be available when writing a file to the filesystem, a trick is
employed while preparing an OpenWRT image: the blank filesystem image
that Yafut operates on initially contains two extra erase blocks that
are chopped off after the kernel file is written.  This is safe to do
because Yaffs2 has a true log structure and therefore only ever writes
sequentially (and the size of the kernel file is known beforehand).
While the two extra erase blocks are necessary for writes, Yaffs2 code
seems to be perfectly capable of reading back files from a "truncated"
filesystem that does not contain these extra erase blocks.

In terms of image size, this new approach is only marginally worse than
the current kernel2minor-based one: specifically, upstream Yaffs2 code
needs to write three object headers (each of which takes up an entire
data chunk) when the kernel file is written to the filesystem:

  - an object header for the kernel file when it is created,

  - an object header for the root directory when the kernel file is
    created,

  - an updated object header for the kernel file when the latter is
    fully written (so that its new size can be recorded).

kernel2minor only writes two of these headers, which is the absolute
minimum required for reading the file back.  This means that the
Yafut-based approach causes firmware images to be at most one erase
block (64 kB) larger than those created using kernel2minor, but only in
the very unfortunate scenario where the size of the kernel file is
really close to a multiple of the erase block size.

The rest of the calculations performed when the empty filesystem image
is first prepared stems from the Yaffs2 layout used by MikroTik NOR
devices: each 65,536-byte erase block contains 63 chunks, each of which
consists of 1024 bytes of data followed by 16-byte Yaffs tags without
ECC data; each such group of 63 chunks is then followed by 16 bytes of
padding, which translates to "-C 1040 -B 64k -E" in the Yafut
invocation.  Yaffs2 checkpoints and summaries are disabled (using
Yafut's -P and -S switches, respectively) as they are merely performance
optimizations that require extra storage space.  The -L and -M switches
are used to force little-endian or big-endian byte order (respectively)
in the resulting filesystem image, no matter what byte order the build
host uses.  The tr invocation is used to ensure that the filesystem
image is initialized with 0xFF bytes (which are an indicator of unused
space for Yaffs2 code).

Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-05 17:03:24 +02:00
Daniel Golle
683a35098f ipq40xx: use NVMEM-on-UBI for ASUS RT-AC58U
Instead of extracting WiFi precal as well as MAC addresses in userspace
use recently introduced NVMEM-on-UBI instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
2024-06-05 13:46:00 +01:00
Luis Mita
f1091ef7ac ramips: mt76x8: add support for Cudy TR1200 v1
Hardware:
 - SoC: MediaTek MT7628AN (MIPS 580MHz)
 - Flash: 16 MiB XMC 25QH128CH10
 - RAM: 128 MiB ESMT M14D1G1664A
 - WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
 - Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
 - USB 2.0 port
 - Buttons: 1 Reset button, 1 slider button
 - LEDs: 1x Red, 1x White
 - Serial console: unpopulated header, 115200 8n1
 - Power: 5 VDC, 2 A

MAC addresses:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 80:af:ca:xx:xx:x0 | label     |
| LAN     | 80:af:ca:xx:xx:x0 | label     |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label     |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2   |
+---------+-------------------+-----------+

Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.

To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.

If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-06-05 10:44:44 +02:00
Robert Marko
f5df45efa3 airoha: drop kernel 6.1 support
Now that 6.6 is the default, lets remove 6.1.

Link: https://github.com/openwrt/openwrt/pull/15630
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-05 09:34:06 +02:00
Robert Marko
690ec44141 airoha: default to kernel 6.6
Move airoha do kernel 6.6 as the default.

Link: https://github.com/openwrt/openwrt/pull/15630
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-05 09:34:06 +02:00
Shiji Yang
6e51b363e9 ramips: simplify multi-phy support patches
For MT7620, we should always prevent main ethernet interface from
going down due to phy link changes. And the ralink net driver does
not support cable test function, so this patch won't change any
behavior.

Ref:
6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15591
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2024-06-04 16:19:41 +08:00
Mieczyslaw Nalewaj
65f34e9928 bcm47xx: 6.6: refresh patches
CI tells us that we need to, so lets refresh them.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Mieczyslaw Nalewaj
a82b2e79e3 bcm47xx: 6.6: set testing kernel
Select 6.6 as testing kernel on bcm47xx.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Mieczyslaw Nalewaj
5285a7d2b1 bcm47xx: remove 5.15 support
Since 6.1 is now default, drop 5.15 support.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Mieczyslaw Nalewaj
f75b530d20 bcm47xx: default to kernel 6.1
Default to kernel 6.1 on bcm47xx.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Mieczyslaw Nalewaj
29aa1a94c4 bcm47xx: 6.6: refresh patches
Refresh kernel patches. Remove patches already included in the kernel.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Mieczyslaw Nalewaj
930eedaafe bcm47xx: 6.6: refresh kernel config
Refresh kernel config.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Mieczyslaw Nalewaj
83647098a1 kernel/bcm47xx: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.

See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Mieczyslaw Nalewaj
907c1c5fe1 kernel/bcm47xx: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 17:57:54 +02:00
Chukun Pan
29faf53b8c qualcommax: use ath11k_patch_mac for ZBT-Z800AX
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15580
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-06-03 13:15:48 +02:00
David Bauer
d4acd05218 mpc85xx: refresh patches
Signed-off-by: David Bauer <mail@david-bauer.net>
2024-06-02 22:43:46 +02:00
David Bauer
63239a939f mpc85xx: fix patch for kernel 6.6
Fixes: af329ec389 ("mpc85xx: add support for Hewlett Packard MSM460")

Signed-off-by: David Bauer <mail@david-bauer.net>
2024-06-02 22:43:46 +02:00
Keith Harrison
6707eba9f0 ramips: add support for D-Link DIR-2055 A1
Add support for D-Link DIR-2055 A1 based on similarities to DIR-1960 A1,
as well as various DIR-8xx A1 models. Existing DIR-1960 A1 openwrt
"factory" firmware installs without modifications via the D-Link Recovery
GUI and has no known incompatibilities with the DIR-2055 A1.

Changes to be committed:
new file:   target/linux/ramips/dts/mt7621_dlink_dir-2055-a1.dts
modified:   target/linux/ramips/image/mt7621.mk
modified:   target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
modified:   target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh

Specifications:

    Board: Not known
    SoC: MediaTek MT7621 Family (MT7621AT)
    RAM: 256 MB (Micron 9OK17 D9PTK, should be DDR3 MT41K128M16JT-125)
    Flash: 128 MB (Winbond W29N01HVSINA)
    WiFi: MediaTek MT7615 Family (MT7615N x2)
    Switch: 1 WAN, 4 LAN (Gigabit)
    Ports: 1 USB 3.0 (front)
    Buttons: Reset, WiFi Toggle, WPS
    LEDs: Power (white/orange), Internet (white/orange),
          WiFi 2.4G (white), WiFi 5G (white)

Notes:

    Only known difference vs. the DIR-1960 A1 is that the DIR-2055 A1
    doesn't have a USB activity LED

Serial port:

    Tested to be identical to various DIR-8xx A1 models with a similar
    enclosure/pcb design:
        Parameters: 57600, 8N1, 3.3V TTL no flow control
        Location: J1 header (close to the Reset, WiFi and WPS buttons)
        Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND
            Did not connect VCC when using

Installation:

    D-Link Recovery GUI: power down the router, press and hold the reset
    button, then re-plug it. Keep the reset button pressed until the power
    LED starts flashing orange, manually assign a static IP address under
    the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to
    http://192.168.0.1

    Some modern browsers may have problems flashing via the Recovery GUI,
    if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

Signed-off-by: Keith Harrison <keithh@protonmail.com>
2024-06-02 18:41:17 +02:00
Hauke Mehrtens
21213c8156 tegra: Activate CONFIG_SND_DRIVERS
The option CONFIG_SND_DRIVERS is activated by default in the generic
configuration, do not deactivate it for tegra. This fixes the build of
the kmod-sound-dummy package on tegra.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-06-02 17:56:28 +02:00
Hauke Mehrtens
8647ce0800 kernel: Split kmod-video-dma into two kmods
Split the kmod-video-dma into kmod-video-dma-sg and
kmod-video-dma-contig. The old one contained two kmods, but sometimes
only one of them is build which caused problems. The configuration
options are not manually selectable in the kernel and hidden in OpenWrt.

Currently this causes build failures on some targets.

Fixes: 4d7cbe0a55 ("kernel: video-dma: explicitly state packaged modules")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-06-02 17:38:23 +02:00
Christian Marangi
37ff0ea726 mvebu: disable polling delay for passive trip point for puzzle thermal
We don't have any passive trip point hence we can set the polling delay
for passive trip to 0 effectively disabling this polling.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-06-01 16:40:10 +01:00
Christian Marangi
611413cc3f mvebu: split thermal zone for puzzle chassis
Split thermal zone for puzzle chassis. Thermal platform supports only
one sensor per thermal zone.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-06-01 16:40:10 +01:00
Christian Marangi
e5c7b5ec43 mvebu: fix missing property in puzzle thermal
Fix missing property in puzzle thermal. The thing was never supposed to
work.

Property #thermal-sensor-cells was missing from the puzzle hwmon, making
the entire thermal platform referencing that fail to probe with -EINVAL.

The puzzle hwmon expose 2 termistor but they probably use an userspace
downstream utility to configure and handle thermal. For this reason we
really don't know what they use the sensor for or when it's attached.

We use them to sensor if the Chassis gets too hot due to ambient
temperature and generic components getting too warm.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-06-01 16:40:10 +01:00
Daniel Golle
ac783b419b mvebu: improve thermal management of IEI Puzzle devices
- Make step_wise thermal governor respect hysteresis
   This is done by importing a downstream patch, backporting the same feature
   now present in Linux v6.10+ would be too messy.
 - Introduce thermal zone for the WT61P803 uC (chassis and board sensors)
 - Introduce thermal zones for AQR NBase-T PHYs
 - No longer modify existing SoC thermal zones (which are now only in charge
   for emergency shutdown, and can be interrupt driven instead of polled)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-06-01 16:40:10 +01:00
David Bauer
dbc9596c7e mpc85xx: add label-mac for HP MSM460
Signed-off-by: David Bauer <mail@david-bauer.net>
2024-06-01 16:53:17 +02:00
David Bauer
af329ec389 mpc85xx: add support for Hewlett Packard MSM460
Hardware
--------
CPU:  Freescale P1020 2xe500 PPC
RAM:  256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ")
NAND: 128M (Micron 2CA1)
BTN:  1x Reset
LED:  Power - ETH - Radio1 - Radio2
UART: RJ-45 Cisco Pinout - 115200 8N1

Installation
------------
NOTE: You can find a repo with up-to-date instructions as well as
the required files here:

https://github.com/blocktrron/msm460-flashing

Required files
==============
You need a command-files as well as a U-Boot image.

The command-file has the following content (padded to 131072 bytes).

If you copy paste these, remove the newlines!

```
U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin;
nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset
```

You can download the required U-Boot from this repository:

https://github.com/blocktrron/u-boot-msm/releases

Preparation
===========
Prepare a TFTP server serving two files:

 - U-Boot NAND image as `msm460-uboot.bin`.
 - OpenWrt factory image as `msm460-factory.bin`
 - Command-file names `commands.tftp`

You can start a TFTP server in the current directory using dnsmasq:

```bash
sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \
    --port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \
    --user=root --group=root
```
Replace `enxd0` with the name of your network interface.

Procedure
=========
1. Assign yourself the IP-Address 192.168.1.66/24.
3. Connect the Router to the PC while keeping the reset button
   pressed.
4. The LEDs will eventually begin to flash.
   They will start to flash faster after around 15 seconds.
5. Release the reset button.
6. Start a new shell
7. Make sure you are currently in the directory where the tftp server
   is located.
8. Run the following command:

```bash
tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999
```

You get the message "Transfer timed out."
To find out if you have been successful, please check the
blinking LED Pattern.

Signed-off-by: David Bauer <mail@david-bauer.net>
2024-06-01 14:41:11 +02:00
David Bauer
7d768a9ba6 mpc85xx: add compressed zImage for mpc85xx
Add a universal zImage which can be loaded by mpc85xx boards at
load address 0x3000000. This allows boards to boot kernels larger than
16MB even if the image is loaded temporarily from NAND at offset
0x1000000 which some bootloaders do by default.

Signed-off-by: David Bauer <mail@david-bauer.net>
2024-06-01 14:37:43 +02:00
Zoltan HERPAI
8619d7af67 kirkwood: add D-Link DNS-320L support
Dual-slot NAS based on Marvell Kirkwood.

Specifications:
 - Marvell 88F6702 @1GHz
 - 256Mb RAM
 - 128Mb NAND
 - 1x GbE LAN (Marvell 88E1318R)
 - 1x USB 2.0
 - 2x SATA
 - Weltrend WT69P3 ("supervisor" MCU chip)
 - Serial on J2 (115200,8n1)
 - Newer bootROM so kwboot-ing via serial is possible

Notes:
 - The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
 - The original MAC address is stored in the "mini firmware" image's first
   17 bytes.
 - Compared to the original MTD layout, the uImage+rootfs are now stored in
   a common ubi partition.

Installation:
1. Serial console
 - Connect your levelshifter to the serial console
   on J2 (refer to the wiki page for pinout)
2. Update u-boot
 - Download the u-boot.kwb image for the device
 - Powercycle the NAS
 - Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
 - Connect to the serial console with minicom
 - tftp 0x0800000 u-boot-dns320l/u-boot.kwb
   (Please note that "PHY reset timed out" seems to be customary
    on kirkwood devices, the egiga0 interface works regardless.)
 - nand erase 0x0 100000
 - nand write 0x0800000 0x0 0x100000
 - reset
3. Install OpenWrt
 - Boot up the initramfs image
 - tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
 - Download the sysupgrade image and perform sysupgrade

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-06-01 01:29:09 +02:00
Tomasz Maciej Nowak
b1bddb1d35 tegra: enable VDE driver
Upstream commit 83b7f0b8aeab ("ARM: tegra: Add OPP tables and power
domains to Tegra20 device-trees") added power domains to all devices
supporting power management and one of them is Video Decoder Engine.
Because of lacking driver for VDE, its power gate couldn't be driven
which inhibited reboot of the whole device.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-31 14:38:17 +02:00
Tomasz Maciej Nowak
192ab0903f tegra: add testing 6.6 kernel
Preliminary support.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-31 14:38:17 +02:00
Tomasz Maciej Nowak
4ff770e763 tegra: 6.6: refresh config and patches
Simple refresh to get rid of any fuzz and drop serial patch. With few
bug fixes around tegra serial driver the spurious IRQ didn't appear any
more during test. Let's see how long that'll last.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-31 14:38:17 +02:00
Tomasz Maciej Nowak
2f7b5d5472 kernel/tegra: Restore kernel files for v5.15
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-31 14:38:17 +02:00
Tomasz Maciej Nowak
b693eca468 kernel/tegra: Create kernel files for v6.6 (from v5.15)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-31 14:38:17 +02:00
Tomasz Maciej Nowak
c1a09173ab tegra: refresh 5.15 config
Reduce diffstat in kernel config on new version introduction.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-31 14:38:17 +02:00
Daniel Golle
2a25c6ace8 ramips: get rid of downstream network device label patch
Use a simple Shell script like on filogic target to get rid of downstream
patch for the Ethernet driver which was rejected upstream long ago.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-31 13:26:54 +01:00
Daniel Golle
983222605c mediatek: filogic: avoid sub-shell invovation in netdev rename loop
Rename network devices to their label set in DT without invocation of
a sub-shell.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-31 13:26:54 +01:00
Hauke Mehrtens
77bfe5441e x86: Activate CONFIG_FB_DEVICE
This adds the legacy /dev/fb* device file for kernel 6.6 again.
Linux upstream commit 701d2054fa31 ("fbdev: Make support for
userspace interfaces configurable") made this configurable and we
deactivated this option by default for kernel 6.6. On x86 we are not
space constrained and some users need this legacy interface.

Fixes: #15222
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-31 11:25:48 +02:00
Mieczyslaw Nalewaj
50e26e6fd7 x86: drop 6.1 support
Drop configs, files and patches for Linux 6.1.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-30 22:47:59 +02:00
Mieczyslaw Nalewaj
06d5d7b7bf x86: use kernel 6.6 by default
Switch to Linux kernel version 6.6.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-30 22:47:59 +02:00
Hauke Mehrtens
fd47fdf527 armsr: Remove kernel 6.1 configuration
Armsr is using kernel 6.6 by default now, remove configuration for
kernel 6.1.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-30 22:44:57 +02:00
Hauke Mehrtens
00f7b252c5 armsr: Use kernel 6.6 by default
All 2 subtargets are compiling fine and booting up in qemu.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-30 22:44:57 +02:00
Daniel Golle
a1a9572f43 generic: 6.6: net: sfp-bus: fix SFP mode detect from bitrate
Backport commit fixing detection of SFP modules which has been broken
since Linux 6.4 for some modules.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-30 12:06:26 +01:00
Daniel Golle
f3d2829b51 generic: backport accepted and pending patches for mtk_eth_soc
Backport a bunch of fixes and improvements for WED and PPE, mostly
for MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-30 10:49:59 +01:00
Daniel Golle
8730f9e536 generic: move accepted patches for mtk_eth_soc to backport-6.6
In preparation to update to upcoming Linux 6.6.33 move accepted patches
from mediatek target to backport folder, so moving to newer Linux 6.6
releases becomes easier and also other patches on top can be applied
more easily.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-30 10:49:46 +01:00
Daniel Golle
bc59bf2a35 kernel: add missing patch header
Make sure all patches can again be applied using 'git am' on the
corresponding linux-stable git tree.

Fixes: a7ae4ed0a3 ("kernel: fix tools build breakage on macos with x86")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-30 10:49:46 +01:00
John Audia
10d77b9bc3 kernel: bump 6.6 to 6.6.31
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.31

Removed upstreamed:
	backport-6.6/600-v6.9-01-net-gro-parse-ipv6-ext-headers-without-frag0-invalid.patch[1]
	backport-6.6/600-v6.9-02-net-gro-fix-udp-bad-offset-in-socket-lookup-by-addin.patch[2]
	backport-6.6/600-v6.9-03-net-gro-add-flush-check-in-udp_gro_receive_segment.patch[3]
	backport-6.6/816-v6.7-0002-nvmem-add-explicit-config-option-to-read-old-syntax-.patch[4]
	pending-6.6/681-net-bridge-fix-multicast-to-unicast-with-fraglist-GS.patch[5]
	pending-6.6/682-net-core-reject-skb_copy-_expand-for-fraglist-GSO-sk.patch[6]
	pending-6.6/684-net-bridge-fix-corrupted-ethernet-header-on-multicas.patch[7]
	pending-6.6/778-net-l2tp-drop-flow-hash-on-forward.patch[8]
	pending-6.6/440-mtd-don-t-look-for-OTP-legacy-NVMEM-cells-if-proper-.patch[9a,b]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=7f7b0ebb37afc5070d122318e3651d7cb8c4f01c
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=af276a5ac8e938c8b058e3e124073cc1e322d98b
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=78b6092d78341e423e5f6afae4d9f401b561aca7
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=26e2fe4cab10e67f116f4a2eecc393824bb294b8
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=65fbc7a11d063236e1f1dcebb38eeaa3ccbe2dbc
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=cfe34d86ef9765c388f145039006bb79b6c81ac6
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=1ce60741d7e17dcf707e3bdebed4442ae30bdd02
8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=23e25d2fc777cd0cc77c2f857f93e9b13ee789b9
9a. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.31&id=cce311f8bbbf9d24eacc39af3228cd104e079396
9b. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/drivers/mtd/mtdcore.c?id=v6.6.31&id2=v6.6.30

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-05-30 00:04:12 +02:00
Zoltan HERPAI
46ce2a36d8 d1: drop 6.1 support
Now that 6.6 is the default, remove the 6.1 config and patches.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-29 17:56:28 +02:00
Zoltan HERPAI
745ad016d1 d1: switch default to 6.6
Switch the default kernel to 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-29 17:56:28 +02:00
Zoltan HERPAI
e78a0cf3ce d1: 6.6: set testing kernel
Allow selecting 6.6 as testing kernel on d1.

Runtime-tested: Nezha D1

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-29 17:56:28 +02:00
Zoltan HERPAI
8b1d74371b d1: refresh kernel config
Refresh kernel config, and enable thermal features.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-29 17:56:28 +02:00
Zoltan HERPAI
2e0b000e0e d1: remove upstreamed patches and add new patchset
Remove patches that were upstreamed, and backport features from
later kernels.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-29 17:56:28 +02:00
Zoltan HERPAI
766570d60b kernel/d1: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-29 17:56:28 +02:00
Zoltan HERPAI
99fcc90270 kernel/d1: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-29 17:56:28 +02:00
Shiji Yang
db49d995bb ramips: modules: remove symbol CONFIG_DW_DMAC_PCI
The DW_DMAC_PCI symbol won't be automatically selected at all.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-29 10:41:49 +02:00
Shiji Yang
2240320d7f ramips: gdma: remove slave_id field
Fix compile error:
drivers/dma/ralink-gdma.c: In function 'gdma_dma_config':
drivers/dma/ralink-gdma.c:197:40: error: 'struct dma_slave_config' has no member named 'slave_id'
  197 |                 chan->slave_id = config->slave_id;
      |                                        ^~
drivers/dma/ralink-gdma.c:206:40: error: 'struct dma_slave_config' has no member named 'slave_id'
  206 |                 chan->slave_id = config->slave_id;
      |                                        ^~
make[8]: *** [scripts/Makefile.build:243: drivers/dma/ralink-gdma.o] Error 1

ref: https://lore.kernel.org/all/20211122222203.4103644-1-arnd@kernel.org/

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-29 10:41:49 +02:00
Shiji Yang
ccd50abd9f ramips: add back the gdma driver
The gdma driver has been removed from the upstream. Let's move it
to the local files. This patch also removed unsupported compatible
string and sub-target.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-29 10:41:49 +02:00
Daniel Golle
4f078bf377 mediatek: add missing ';;' in shell switch case block
Add missing ';;' to the end of shell switch case statement.

Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Reported-by: @gl-dude
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-28 23:51:38 +01:00
Hauke Mehrtens
3a2706ed10 malta: Remove kernel 6.1 configuration
Malta is using kernel 6.6 by default now, remove configuration for
kernel 6.1.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-28 22:10:53 +02:00
Hauke Mehrtens
5f0e591349 malta: Use kernel 6.6 by default
All 4 subtargets are compiling fine and booting up in qemu.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-28 22:10:52 +02:00
Nick Hainke
9ec3b11d37 lantiq: disable building of ZyXEL P-2812HNU F1
Disable image building for the board, since the kernel of the main branch
is to big to fit into the kernel partition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-05-28 08:06:10 +02:00
Martin Schiller
7514d9bb6f lantiq: switch to kernel 6.1
Let's switch the lantiq target to use kernel 6.1 by default.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-27 15:46:13 +02:00
Tomasz Maciej Nowak
f7f8099aa3 ath79: add support for Dell SonicPoint ACe APL26-0AE
Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
wireless access point. End of life as of 2022-07-31.

Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
      5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
          port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 2x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
        baud: 115200, parity: none, flow control: none

Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
All described procedures were done in following environment:
ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
SafeMode Firmware Version: SonicOS 8.0.0.0-14o
Firmware Version: SonicOS 9.0.1.0
In case of other versions, following installation instructions might be
ineffective.

Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
   image to "sp_fw.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
   power on the device and when prompted to stop autoboot, hit any key.
   The held button can now be released.
5. Alter U-Boot environment with following commands:
    setenv bootcmd bootm 0x9F110000
    saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
   (TFTP server, default is 192.168.1.10) addresses in U-Boot
   environment, then run following commands:
    tftp 0x80060000 sp_fw.bin
    erase 0x9F110000 +0x1EF0000
    cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
    boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
    wrench LED will stop blinking, then it's ready for configuration.

Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
causes hang on reboot, thus broken-flash-reset needs to be added. This
property addition causes dispaly of "scary" warning on each boot, take
this warnig into consideration.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-27 00:32:57 +02:00
Mieczyslaw Nalewaj
1a2fc49b71 ramips: samknows whitebox v8: set wifi frequency
Set the 2.4GHz frequency for WiFi.

Fixes: #15391
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-25 20:20:30 +02:00
Pawel Dembicki
1b24cbeede layerscape: add 6.6 testing kernel
Support is ready. Let's enable 6.6 as testing version.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-05-25 20:18:23 +02:00
Pawel Dembicki
d73a66be61 layerscape: adjust dts path in image scripts
After the spliting dts folder of ARM architecture in upstream,
layerscape routines need to be adjusted for new solution.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-05-25 20:18:23 +02:00
Pawel Dembicki
ec956af626 layerscape: refresh 6.6 config
Mostly done by 'make kernel_oldconfig'.

armv8_64b has added one entry manually:
CONFIG_CRYPTO_CURVE25519=y

as workaround for error:
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
	`crypto_engine_register_kpp':
crypto_engine.c:687: undefined reference to `crypto_register_kpp'
crypto_engine.c:687:(.text+0x57c): relocation truncated to fit:
	R_AARCH64_CALL26 against undefined symbol `crypto_register_kpp'
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
	`crypto_engine_unregister_kpp':
crypto/crypto_engine.c:693: undefined reference to `crypto_unregister_kpp'
crypto_engine.c:693:(.text+0x5a0): relocation truncated to fit:
	R_AARCH64_CALL26 against undefined symbol `crypto_unregister_kpp'

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-05-25 20:18:23 +02:00
Pawel Dembicki
c9ecca141a generic: kernel add 6.6 missing symbols
Found durring works on layerscape.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-05-25 20:18:23 +02:00
Pawel Dembicki
347212085b layerscape: kernel: refresh 6.6 patches
Taken refreshed version from Layerscape 6.6 tree:
302-arm64-dts-ls1012a-update-with-ppfe-support.patch
304-arm64-dts-ls1012a-rdb-workaround-by-updating-qspi-fl.patch
400-LF-20-3-mtd-spi-nor-Use-1-bit-mode-of-spansion-s25fs.patch
701-staging-add-fsl_ppfe-driver.patch
702-phy-Add-2.5G-SGMII-interface-mode.patch
704-net-phylink-treat-PHY_INTERFACE_MODE_2500SGMII-in-ph.patch

Removed:
704-net-phylink-treat-PHY_INTERFACE_MODE_2500SGMII-in-ph.patch (meld
into 702)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-05-25 20:18:23 +02:00
Pawel Dembicki
af1fc05cad kernel/layerscape: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.

See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-05-25 20:18:23 +02:00
Pawel Dembicki
0a22ccaad6 kernel/layerscape: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

During a `git bisect` session, `git bisect --skip` is recommended.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2024-05-25 20:18:23 +02:00
INAGAKI Hiroshi
34c875cf8b mvebu: add support for Fortinet FortiWiFi 51E
Fortinet FortiWiFi 51E (FWF-51E) is a UTM with 1x WLAN and 1x SSD, based
on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD          : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
  - mode       : SATA III 6Gbps
  - power      : 3.3 VDC, 3.1 W (Max.)
- Ethernet     : 7x 10/100/1000 Mbps
  - LAN 1-5    : Marvell 88E6176
  - WAN 1, 2   : Marvell 88E1512 (2x)
- WLAN         : Fortinet EMP7618-FT (Atheros AR9382 (2T2R))
  - interface  : MiniPCIe
- LEDs/Keys    : 18x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                 5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Molex 5557-02R

Flash instruction using initramfs image:

 1. Power on FWF-51E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "R" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN  : 88:DC:96:xx:xx:xx (MiniPCIe Card)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
2024-05-25 20:03:00 +02:00
INAGAKI Hiroshi
26a2135c6d mvebu: add support for Fortinet FortiWiFi 50E-2R
Fortinet FortiWiFi 50E-2R (FWF-50E-2R) is a UTM with 2x WLAN, based on
Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 2 GiB (4x Nanya NT5CC512M8EN-EK)
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 7x 10/100/1000 Mbps
  - LAN 1-5    : Marvell 88E6176
  - WAN 1, 2   : Marvell 88E1512 (2x)
- WLAN         : Gemtek WMDQ-177ACN (Qualcomm Atheros QCA9892 (2T2R))
                 (2x)
  - interface  : MiniPCIe
- LEDs/Keys    : 18x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                 5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2.5 A
  - plug       : Molex 5557-02R

Flash instruction using initramfs image:

 1. Power on FWF-50E-2R and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "R" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F
WLAN 1: 1C:49:7B:xx:xx:xx (MiniPCIe Card)
WLAN 2: 1C:49:7B:xx:xx:xx (MiniPCIe Card)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
2024-05-25 20:03:00 +02:00
INAGAKI Hiroshi
38d6c99dc0 mvebu: add support for Fortinet FortiGate 52E
Fortinet FortiGate 52E (FG-52E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD          : mSATA SSD 64 GB (2x A-DATA XM21E (AXM21ES3-32GM-B))
  - mode       : SATA III 6Gbps
  - power      : 3.3 VDC, 3.1 W (Max.)
- Ethernet     : 7x 10/100/1000 Mbps
  - LAN 1-5    : Marvell 88E6176
  - WAN 1, 2   : Marvell 88E1512 (2x)
- LEDs/Keys    : 18x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                 5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2.5 A
  - plug       : Molex 5557-02R

Flash instruction using initramfs image:

 1. Power on FG-52E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "R" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 90:6C:AC:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 90:6C:AC:xx:xx:99
WAN 2 : 90:6C:AC:xx:xx:9A
LAN 1 : 90:6C:AC:xx:xx:9B
LAN 2 : 90:6C:AC:xx:xx:9C
LAN 3 : 90:6C:AC:xx:xx:9D
LAN 4 : 90:6C:AC:xx:xx:9E
LAN 5 : 90:6C:AC:xx:xx:9F

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 20:03:00 +02:00
INAGAKI Hiroshi
d406498e1b mvebu: add support for Fortinet FortiGate 51E
Fortinet FortiGate 51E (FG-51E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- SSD          : mSATA SSD 32 GB (A-DATA XM21E (AXM21ES3-32GM-B))
  - mode       : SATA III 6Gbps
  - power      : 3.3 VDC, 3.1 W (Max.)
- Ethernet     : 7x 10/100/1000 Mbps
  - LAN 1-5    : Marvell 88E6176
  - WAN 1, 2   : Marvell 88E1512 (2x)
- LEDs/Keys    : 18x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                 5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2.5 A
  - plug       : Molex 5557-02R

Flash instruction using initramfs image:

 1. Power on FG-51E and interrupt to show bootmenu
 2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
    and set baudrate to 9600 bps
 3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
    connect computer to "Image download port" in the parameters
 4. Prepare TFTP server with the parameters obtained above
 5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
    directory
 6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
    image from TFTP server
 7. Type "R" key when the following message is showed, to boot initramfs
    image without flashing to spi-nor flash

    "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

 8. On initramfs image, backup mtd if needed

    minimum:

    - "firmware-info"
    - "kernel"
    - "rootfs"

 9. On initramfs image, upload sysupgrade image to the device and perform
    sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
    If the device is booted with stock firmware, login to bootmenu and
    call "[B]: Boot with backup firmware and set as default." to set the
    first OS image as default and boot it.

Notes:

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:98 (board-info (OpenWrt), 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:99
WAN 2 : 70:4C:A5:xx:xx:9A
LAN 1 : 70:4C:A5:xx:xx:9B
LAN 2 : 70:4C:A5:xx:xx:9C
LAN 3 : 70:4C:A5:xx:xx:9D
LAN 4 : 70:4C:A5:xx:xx:9E
LAN 5 : 70:4C:A5:xx:xx:9F

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Tested-by: Raylynn Knight <rayknight@me.com>
2024-05-25 20:03:00 +02:00
INAGAKI Hiroshi
f69d96a8e5 mvebu: separate common parts to new dtsi for FortiGate/FortiWiFi 5xE
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 5xE series devices.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 20:03:00 +02:00
INAGAKI Hiroshi
77663df754 mvebu: separate common parts to new dtsi for FortiGate/FortiWiFi 3xE
Add a new dtsi which contains the common parts of Fortinet
FortiGate/FortiWiFi 3xE series devices.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 20:03:00 +02:00
INAGAKI Hiroshi
73be4b9e48 mvebu: rename common dtsi of FortiGate 30E/50E
Rename the common dtsi of Fortinet FortiGate 30E/50E for the preparation
of adding support for the other FortiGate/FortiWiFi 3xE/5xE devices.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 20:03:00 +02:00
INAGAKI Hiroshi
0618eae506 mvebu: add common image definition for FortiGate devices
Add a common definition of Fortinet FortiGate devices to
image/cortexa9.mk for a preparation of adding support for
other FortiGate 3xE/5xE devices.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 20:02:59 +02:00
Kristian Skramstad
c5b7ec8cee ath79: qca9563: add support for Amplifi Router HD
Hardware:
    SoC: Qualcomm Atheros QCA956X ver 1 rev 0
    CPU clock: 775.000 MHz
    Memory: 128 MB DDR2
    Flash: 32 MB SPI NOR mx25l25635e
    Switch: Atheros AR8327 rev. 4
    Ethernet: 5x 10/100/1000 Mbps (1 WAN + 4 LAN)
    Buttons: 1x Reset
    Serial: TX, RX, GND, VCC
    Baudrate: 115200
    Wifi: Qualcomm Atheros qca988x 802.11ac/n - 3x3
          Qualcomm Atheros AR9561 802.11b/g/n - 3x3

Not working:
    Leds: 1x via a SPI controller
    Display: ST7789V or ILI9341V
    controlled by stm32f205.

Note:
    DSA changes are ready, but we have an issue with
    ports not working after 20-30 minutes. So for now
    we use swconfig.

Installation: serial connection only
There is a J11 four pin connector. You need to connect TX, RX and GND.
You can find very good information about the device here
https://github.com/alexanderhenne/AFi-R?tab=readme-ov-file#finding-j11

Upgrading via serial port:
1.  Download the kernel initramfs image. Copy the image to a TFTP server
2.  Connect to console on the AP, and connect the LAN1 port to your PC LAN
3.  Stop autoboot to get to U-boot shell
    Interrupt the autoboot process by pressing any key when prompted
4.  Transfer the kernel image with TFTP
    Set your ip address on your TFTP server to 192.168.1.254
    # tftpboot 0x81000000 amplifi-router-hd-initramfs-kernel.bin
5.  Load the image
    # bootm 0x81000000
6.  SCP sysupgrade image from your PC to the Amplifi HD
    (If you use a newer mac use scp -O)
    # scp openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7.  Write sysupgrade to the firmware partition
    # mtd write /tmp/openwrt-ath79-generic-ubnt_amplifi-router-hd-squashfs-sysupgrade.bin firmware
8.  Reboot your device
    # reboot

Credit to alexanderhenne for all the information.

Signed-off-by: Kristian Skramstad <kristian+github@83.no>
2024-05-25 19:52:42 +02:00
INAGAKI Hiroshi
50ae9337d6 ramips: add support for ELECOM WRC-X1800GS
ELECOM WRC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7621A.

Specification:

- SoC               : MediaTek MT7621A
- RAM               : DDR3 256 MiB
- Flash             : RAW-NAND 128 MiB (Macronix MX30LF1G28AD-TI)
- WLAN              : 2.4/5 GHz 2T2R (MediaTek MT7915D)
- Ethernet          : 5x 10/100/1000 Mbps
  - switch          : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO)  : 7x/4x
- UART              : pin-header on PCB ("J5")
  - arrangement     : 3.3V, TX, RX, NC, GND from tri-angle marking
  - settings        : 115200n8
- Power             : 12 VDC, 1 A

Flash instruction using initramfs-factory image:

1. Boot WRC-X1800GS normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
   button
4. After flashing initramfs-factory image and reboot, upload the
   sysupgrade image and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing

Notes:

- WRC-X1800GS has 2x os images. Those are switched on every firmware
  updating on stock firmware, but dual-boot feature on this device
  cannot be handled on OpenWrt. So the 1st image is always used on
  OpenWrt.
  This is controlled by "bootnum" variable embedded in "persist"
  partition (addr: 0x4).

- WRC-X1800GS has 2x HW revisions. There are some small changes, but the
  same DeviceTree in stock firmware is used for both revisions.
  On this support of WRC-X1800GS, 2x green:wlan-2g-N LEDs are defined
  for each revision and the same default triggers are set.

MAC addresses:

LAN    : 38:97:A4:xx:xx:38 (Factory, 0x1fdfa (hex) / Ubootenv, ethaddr (text))
WAN    : 38:97:A4:xx:xx:3B (Factory, 0x1fdf4 (hex))
2.4 GHz: 38:97:A4:xx:xx:39
5 GHz  : 38:97:A4:xx:xx:3A

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 19:33:28 +02:00
INAGAKI Hiroshi
cd2a6906da ramips: parameterize some values in Build/znet-header
Parameterize magic number and header length to use the device-specific
values.

example:

On WRC-X1800GS, an additional ELECOM-specific header and a magic number
"COMC" are required.

Stock FW v1.18:

$ hexdump -n $((0x40080)) -C wrc-x1800gs_v1.18.bin
00000000  45 4c 45 43 4f 4d 00 00  57 52 43 2d 58 31 38 30  |ELECOM..WRC-X180|
00000010  30 47 53 00 00 00 00 00  00 00 00 00 00 00 00 00  |0GS.............|
00000020  00 00 00 00 00 00 00 00  31 2e 31 38 00 00 00 00  |........1.18....|
00000030  00 00 00 00 00 00 00 00  43 4f 4d 43 04 00 ac 00  |........COMC....|
00000040  40 f0 49 74 b1 e8 6a ca  e4 20 65 1f 34 2e 30 34  |@.It..j.. e.4.04|
00000050  28 58 56 46 2e 31 29 62  31 37 00 00 00 00 00 00  |(XVF.1)b17......|
00000060  00 00 00 00 00 00 00 00  ff ff ff ff ff ff ff ff  |................|
00000070  ff ff ff ff ff ff ff ff  ff ff ff ff ff ff ff ff  |................|
*
00040000  d0 0d fe ed 00 36 9c c0  00 00 00 38 00 36 9a e0  |.....6.....8.6..|
00040010  00 00 00 28 00 00 00 11  00 00 00 10 00 00 00 00  |...(............|
00040020  00 00 00 6c 00 36 9a a8  00 00 00 00 00 00 00 00  |...l.6..........|
00040030  00 00 00 00 00 00 00 00  00 00 00 01 00 00 00 00  |................|
00040040  00 00 00 03 00 00 00 04  00 00 00 62 65 54 97 8f  |...........beT..|
00040050  00 00 00 03 00 00 00 28  00 00 00 00 4d 49 50 53  |.......(....MIPS|
00040060  20 4f 70 65 6e 57 72 74  20 46 49 54 20 28 46 6c  | OpenWrt FIT (Fl|
00040070  61 74 74 65 6e 65 64 20  49 6d 61 67 65 20 54 72  |attened Image Tr|
00040080

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-25 19:33:28 +02:00
Ryan Castellucci
85f6f88223 ipq40xx: eap1300: add eap1300ext as alt model
The EnGenius EAP1300 and EAP1300EXT use identical boards and firmware
(as flashed) from the vendor.

As with the EAP1300, the EAP1300EXT requires a specific firmware version
to flash OpenWRT. Unfortunately, the required firmware is truncated on
the vendor's website.

A working file can be created as follows:

```
curl \
https://www.engeniustech.com/wp_firmware/eap1300-all-v3.5.3.5_c1.9.04.bin \
| perl -pe 's/\x09EAP1300_A/\x0cEAP1300EXT_A/' \
> eap1300ext-all-v3.5.3.5_c1.9.04.bin
```

The file should have sha256:
`58a1197a426139a12b03fd432334e677124cbe3384349bd7337f2ee71f1dcfd4`.

Please see commit 2b4ac79 for further
details.

The vendor firmware must be decrypted before it can be flashed from
OpenWRT. A tool able to do that is available from:

https://github.com/ryancdotorg/enfringement/blob/main/decrypt.py

Signed-off-by: Ryan Castellucci <code@ryanc.org>
2024-05-25 18:37:09 +02:00
Leon M. Busch-George
a55ab9e134 mediatek: filogic: prevent faulty mac address assignment
The vendor U-Boot on the Cudy M3000 and the Yuncore AX835 assign random
mac addresses on boot and set the 'local-mac-address' property which
prevents Openwrt from assigning the correct address from evmem.

This patch removes the alias for ethernet0 so that U-Boot doesn't add the
property, removes the workaround from 02_network, and adds back the nvmem
definition for the M3000.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2024-05-25 12:41:26 +02:00
Linus Walleij
e7661a808e ixp4xx: Add back support for D-Link DSM G600 A
OpenWrt supported the D-Link DSM G600 A in the past. It has
64 MB of RAM and 16 MB of flash so it will run just fine,
and should be quite usable with a rootfs on an external
harddrive.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-25 09:17:19 +02:00
Linus Walleij
869bbdb8f6 ixp4xx: Add back support for Freecom FSG-3
OpenWrt supported the Freecom FSG-3 in the past. It has
64 MB of RAM so will run fine, but the bare 4 MB of flash
makes it a non-default target. The generated compressed
image is currently below 4MB (just 3.3 MB) though, so it
should be possible to flash just fine with a rootfs on
a harddrive or USB stick, which is what the FSG-3 used
in the past as well.

The device has a WAN port on eth0 and three LAN ports on
eth1. The LAN ports are probably a DSA switch but the
old OpenWrt base never activated that, instead it relies
on boot defaults.

Due to questionable usablity without tweaking and further
work this image is not built by default, but made available
for developers who know what they are doing.

The TAR+CRC image generation is a rewritten version of the
earlier support code.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-25 09:17:10 +02:00
Linus Walleij
4220f75d1e ixp4xx: Add back support for Iomega NAS100D
OpenWrt supported the Iomega NAS100D in the past and it has
64 MB of RAM so if booted from a harddrive it will probably
work just fine. The APEX boot loader already has a build
variant for this machine that we can just pick up and use.

This device has a single ethernet port so bring this online
with DHCP as expected for a NAS device.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-25 09:16:45 +02:00
Linus Walleij
e824864ede ixp4xx: Add ext4 and rootfs-part to features
Several of the IXP4xx machines mount root on external harddrives
so add EXT4 and rootfs-part to the featureset so the right
features are always selected.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-25 09:16:34 +02:00
Daniel Golle
c71b68acdd mediatek: filogic: add Adtran SmartRG Mount Stuart series
Common specifications:
 * Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
 * 8 GiB eMMC
 * 2 GiB DDR4 RAM
 * 1x 10000M/1000M/100M + 3x 1000M/100M/10M LAN ports
 * MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
 * Airoha AG3352 GPS
 * Renesas DA14531MOD Bluetooth
 * 2 buttons (Reset, Mesh/WPS)
 * uC-controlled RGB LED via I2C
 * 2x LED for each 1G port, 3x LED for each 10G port
 * USB 3.0 type A port
 * 3.3V-level 115200 baud UART console via 4-pin Dupont connector
   exposed at the bottom of the device
 * USB-C PD power input

SDG-8733: 1x 10000M/1000M/100M WAN port
SDG-8734: 1x USXGMII/10GBase-R/5GBase-R/2500Base-X/1000Base-X/SGMII SFP+

Both models are also available in versions including 2x FXS POTS interfaces
for analog phones. Those interfaces are not supported by OpenWrt.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-24 18:34:13 +01:00
Daniel Golle
c82e106313 mediatek: fix sysupgrade config backup on Adtran SmartRG devices
Add missing call to emmc_copy_config which either writes the sysupgrade
tar.gz backup file or clears the existing rootfs_data overlay.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-24 18:34:13 +01:00
Daniel Golle
cccf98c7e8 generic: 6.6: backports and add LED support for Aquantia PHYs
Backport patch adding support for the AQR114C PHY and add support for
PHY LEDs and polarity setting of Aquantia 3rd and 4th generation PHYs.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-24 18:34:13 +01:00
Andrey Bondar
febcfadc80 ath79: add support for 8Devices Carambola3 board
Carambola3 is a WiFi module based on Qualcomm/Atheros QCA4531
http://wiki.8devices.com/carambola3

Specification:

    - 650/600/216 MHz (CPU/DDR/AHB)
    - 128 MB of RAM (DDR2)
    - 32 MB of FLASH
    - 2T2R 2.4 GHz
    - 2x 10/100 Mbps Ethernet
    - 1x USB 2.0 Host socket
    - UART for serial console
    - 12x GPIO

Flash instructions:

    Upgrading from ar71xx target:
    - Upload image into the board:
        scp openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin \
          root@192.168.1.1/tmp/
    - Run sysupgrade
        sysupgrade -F /tmp/openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin

Upgrading from u-boot:
    - Set up tftp server with openwrt-ath79-generic-8dev_carambola3-initramfs-kernel.bin
    - Go to u-boot (reboot and press ESC when prompted)
    - Set TFTP server IP
        setenv serverip 192.168.1.254
    - Set device ip from the same subnet
        setenv ipaddr 192.168.1.1
    - Copy new firmware to board
        tftpboot 0x82000000 initramfs.bin
    - Boot OpenWRT
        bootm 0x82000000
    - Upload image openwrt-ath79-generic-8dev_carambola3-squashfs-sysupgrade.bin into the board
    - Run sysupgrade.

Signed-off-by: Andrey Bondar <a.bondar@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/15514
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-24 11:29:23 +02:00
Lea Teuberth
2a2f53415e ramips: add support for TP-Link Archer MR200v5
Specifications:
	CPU:     MT7628AN 580MHz
	RAM:     64MB DDR2
	FLASH:   8MB EN25QH64 NOR SPI
	WIFI:    2.4GHz 2x2 MT7628 b/g/n internal
	WIFI:    5GHz 1x1 MT7610E ac/n PCI
	LTE:     Qualcomm MDM9207
	ETH:     4xLAN 100base-T integrated
	SWITCH:  RT3050-ESW Port 0,1,2,3: LAN, Port 6: CPU
	LEDS:    LAN, WAN, Power, 3x signal strength, WiFi
	BTNS:    Reset, WiFi toggle
	UART:    Near ETH ports, Vcc-GND-RX-TX, 115200, 8N1

Installation:
	1. Update using recovery mode
        - set your IP to 192.168.0.225, subnet mask: 255.255.255.0
        - start tftp server, rename tftp-recovery.bin to
          tp_recovery.bin and place it into the server's directory
        - while holdig the "reset" button, power on the device
        - keep holding "reset" until the file is being transferred

Notes:
	This board has only one MAC address programmed
        in the "romfile" partition:
        - MAC for phy0 (2.4GHz) at romfile 0xf100 (0)
        - MAC for phy1 (5GHz) at romfile 0xf100 (-1)
        - stock firmware re-uses phy0 MAC for ethernet
        - stock firmware uses romfile 0xf100 (1) for WWAN;
          not used since QMI interface is raw IP

Signed-off-by: Lea Teuberth <lea.teuberth@outlook.com>
2024-05-23 22:46:26 +02:00
Rafał Miłecki
e83a5618d4 mediatek: include "kmod-mt7915e" package per device
mt7915e driver supports MT7915 & MT7916 devices and MT7981 & MT7986
on-SoC wireless controllers. Devices based on MT7988 and possibly other
next chipsets are quite unlikely to need it (MT7988 was designed to be
used with MT7996).

Move kmod-mt7915e to DEVICE_PACKAGES of relevant devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-05-23 12:24:48 +02:00
Robert Marko
4a78c46cbd ipq40xx: dont panic on PSGMII calibration fail
Currently, in case that PSGMII calibration fails it will panic the kernel
which is not ideal and is preventing any debugging to be done.

So, since PGMII calibration failing only means that wired networking wont
work lets convet the panic() call to dev_error.

Link: https://github.com/openwrt/openwrt/pull/15542
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-22 17:24:17 +02:00
Andrew Smith
0f5c28b96b qualcommax: ipq807x support Netgear Orbi Pro SXK80
This commit adds support for Netgear Orbi Pro SXR80 and SXS80 (collectively known as SXK80)

Specifications:
---------------
* CPU: Qualcomm IPQ8074A Quad core Cortex-A53
* RAM: 1024MB
* Storage: SPI-NAND 512 MiB (Winbond W29N04GZ)
* Ethernet: 4x 1G RJ45 ports (QCA8075) 1x 2.5G RJ45 LAN/WAN (QCA8081)
* WLAN:
    - 2.4 GHz: Qualcomm QCN5024 4x4
    - 2x 5 GHz: Qualcomm QCN5054 4x4 (second radio high channels only)
* LEDs:
    - Power: (Green and red)
    - Front: (Blue, green, red and white)
* Buttons:
    - 1x Soft reset
    - 1x Sync/WPS
* Power: 12V DC Jack

Installation instructions (Telnet):
-----------------------------------

*Note, this guide assumes SXR80, for SXS80 change the firmware file name as appropriate

1. Put firmware file openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb in root of TFTP server available at 192.168.1.10.
2. Enable telnet by going to http://[ip of device]/debug.htm and clicking on the tickbox 'Enable telnet'
3. Telnet into the device and login using the same username and password as the web interface:
4. Run the following command:

`fw_setenv bootcmd 'env default -a; saveenv; reset'`

5. Reboot the router, once the web interface is available again re-enable telnet via http://[ip of device]/debug.htm and telnet into the device.

6. Run the following command:

`fw_printenv`

It should look similar to the below:

```
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot
bootdelay=2
ipaddr=192.168.1.1
netmask=255.255.255.0
serverip=192.168.1.10
soc_version_major=2
soc_version_minor=0
```

**If you see the message:**
`Warning: Bad CRC, using default environment`
**DO NOT CONTINUE, YOU WILL BRICK YOUR DEVICE**

7. Run the following command:

`fw_setenv originalboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; bootdni; boot_DNI_secureboot'`

(This should match what's in the bootcmd variable displayed in step 6)

8. Run the following commands:
```
fw_setenv wrttftp 'mii write 0x0 0x0 0x800; sleep 1; nmrp; if tftpboot openwrt-qualcommax-ipq807x-netgear_sxr80-initramfs-uImage.itb; then bootm; fi; bootdni; boot_DNI_secureboot'
fw_setenv wrtboot 'mii write 0x0 0x0 0x800; sleep 1; nmrp; nand read 0x40000000 0x1980000 0x06d00000; bootm 0x40000000'
fw_setenv bootcmd 'run wrttftp'
```

9. Ensure SXR/S device is attached via ethernet (LAN port) to the same ethernet segment as the TFTP server.

10. Reboot the device, it should reboot into OpenWrt and be available on 192.168.1.1

11. Once OpenWrt has booted, update the bootcmd using the following command:

`fw_setenv bootcmd 'run wrtboot'`

12. Flash the sysupgrade image

13. It should boot into OpenWrt

References to SXK80 GPL source:
https://www.downloads.netgear.com/files/GPL/SXK80-V3.2.0.108_gpl_src.tar.bz2.zip

Signed-off-by: Flole Systems <flole@flole.de>
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/14939
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-22 14:51:36 +02:00
Robert Marko
cd9241db23 qualcommax: ipq807x: sax1v1k: fix QCA8081 reset
It seems that on Spectrum SAX1V1K QCA8081 is being brought out of reset
too quickly and thus causing it to get stuck in an invalid autoneg
register configuration mode.

Setting an deasset delay seems to fix this, so lets set it.

Fixes: #15493
Link: https://github.com/openwrt/openwrt/pull/15541
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-21 20:15:03 +02:00
John Crispin
dd58ad968a mediatek/filogic: add OpenWrt One support
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 1GB RAM
 - 16MB NOR
 - 128MB NAND
 - 3 LEDs (red, green, blue, white)
 - 2 buttons (reset, user defined)
 - 1 2.5Gbit WAN port (Airoha EN8811h)
 - 1 1Gbit LAN ports
 - 1 single lane M.2 SSD slot
 - 1 mikroBus socket
 - externel HW WDT (25s refresh time)
 - i2c RTC (with battery backup)

Serial Interface
 - UBS-C CDC-ACM
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

MAC addresses are not populated on the early samples.

Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 11:35:38 +02:00
John Crispin
47d308a46c Revert "mediatek/filogic: add OpenWrt One support"
This reverts commit 797904b3cb.

There is a stray line in the commit description

Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 11:35:28 +02:00
John Crispin
797904b3cb mediatek/filogic: add OpenWrt One support
filogic: Add support for D-Link AQUILA PRO AI M30

Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 1GB RAM
 - 16MB NOR
 - 128MB NAND
 - 3 LEDs (red, green, blue, white)
 - 2 buttons (reset, user defined)
 - 1 2.5Gbit WAN port (Airoha EN8811h)
 - 1 1Gbit LAN ports
 - 1 single lane M.2 SSD slot
 - 1 mikroBus socket
 - externel HW WDT (25s refresh time)
 - i2c RTC (with battery backup)

Serial Interface
 - UBS-C CDC-ACM
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

MAC addresses are not populated on the early samples.

Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 10:40:20 +02:00
John Crispin
6e060300fc mediatek/filogic: enable led PWM driver by default
Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 10:26:06 +02:00
John Crispin
27286ed524 mediatek/filogic: fix mt7981.dtsi PCIe support
* the compatible string was wrong
* the pinmux was missing

Signed-off-by: John Crispin <john@phrozen.org>
2024-05-21 10:26:06 +02:00
Linus Walleij
2eef4f7354 ixp4xx: Bump to kernel v6.6
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.

Bring in some outstanding patches.

Tested on the Gateworks GW2348-4.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-20 21:04:08 +02:00
Linus Walleij
70e81efe93 gemini: In-flight ethernet patches
These patches have partial acceptance upstream and are still
a WIP, now there is merge window for kernel v6.10 so these
will not be reposted until that is over. In the meantime,
let's add the current state to OpenWrt so the ethernet on
Gemini is up and working (tested on several devices).

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-19 22:06:11 +02:00
Felix Fietkau
ba245d6bca mediatek: add firmware name for AQR PHYs on mt7988a-rfb
Fixes PHY probe in case there is no firmware in a connected EEPROM

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-19 09:47:04 +02:00
Felix Fietkau
59ac0440b1 mediatek: convert mt7988a-rfb to keep bl31/uboot in UBI
Add ubi volumes for mt7988a-rfb and support for using factory data
for Ethernet MAC addresses and MT7996 WLAN calibration data.
Also add rootdisk handle. Removes the need to keep using nmbm

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-19 09:47:04 +02:00
Tomasz Maciej Nowak
6a29d32d8a tegra: trimslice: enable USB HID driver
Without serial or network access the only option for initial
configuration, is a attached display with USB keyboard, but the keyboard
driver needs to be installed first. So enable keyboard driver by default
to avoid this issue.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-17 17:04:24 +03:00
Tomasz Maciej Nowak
6660a15d72 tegra: trimslice: enable GPIO LEDs driver
LEDs are on all the time since boot, until there's driver to claim them.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-17 17:04:24 +03:00
Tomasz Maciej Nowak
a0c5efd3f7 tegra: drop console specifiers from kernel commad line
Because recent changes to procd, last "console" argument was used as
primary argument and causing no terminal to be spawned on serial
interface. So drop the hardcoded consoles in boot script, since dts has
already an alias specified, which lets procd decide where to spawn the
terminal.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-17 17:04:24 +03:00
Tomasz Maciej Nowak
82353d3e3d tegra: pad rootfs to recreate overlay after upgrade
The old overlay remained after upgrades and would cause failure on first
boot after upgrade, in which no new overlay could be created while old
one was unusable.

Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
2024-05-17 17:04:24 +03:00
Paweł Owoc
9bdaebaff3 qualcommax: ipq807x: add support for Linksys MX8500
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Fidelix FMND4G08S3J-ID)
RAM: 1GB (2x Kingston DDR3L D2516ECMDXGJD)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (NXP K32W041)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset

Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/support-article?articleNum=47547
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx8500-squashfs-factory.bin alt_kernel

4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX8500_1.0.11.208937_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX8500_1.0.11.208937_prod.img alt_kernel

5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx8500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

AQR firmware:
========
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

2. Firmware updating:
Newer firmware (AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld) is available in the latest OEM firmware.
To load this firmware via u-boot, we need to add the MBN header and update 0:ethphyfw partition.
For MBN header we can use script from this repository: https://github.com/testuser7/aqr_mbn_tool
- python aqr_mbn_tool.py AQR-G4_v5.6.5-AQR_WNC_SAQA-L2_GT_ID45287_VER24005.cld
To update partition we need to install kmod-mtd-rw package first:
- insmod mtd-rw.ko i_want_a_brick=1
- mtd -e /dev/mtd26 -n write aqr_fw.mbn /dev/mtd26

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 20:27:36 +02:00
Paweł Owoc
7f1c87ebde qualcommax: ipq807x: define common Linksys MX device
Define common Linksys MX device for MX4200v1/v2 and MX5300.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 20:27:36 +02:00
Paweł Owoc
a7c068b935 generic: 6.6: add patch to support AQR114C PHY ID
Add support for AQR114C PHY ID.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 20:27:36 +02:00
Paweł Owoc
b32a17e82d qualcommax: ipq807x: Remove unused gpio from QPIC pins
Remove gpio16 from the default NAND pinctrl configuration
as its unused and only needed for LCD.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14883
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 20:27:36 +02:00
Robert Marko
96e402aef7 ipq806x: mr42/mr52: fix PCIe ports
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.

After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.

However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.

So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.

Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 19:28:16 +02:00
Robert Marko
f12179fa15 generic: 6.6: remove kernel export stripping patch
Our kernel export stripping has been broken on 6.6 from the start since
upstream kernel really reworked stuff in ("kbuild: generate KSYMTAB entries
by modpost") and other commits as well.

So, until this is either fixed or reworked lets drop the patch as it doesnt
make sense to carry it knowing its broken and it can always be easily
restored.

Link: https://github.com/openwrt/openwrt/pull/15498
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-16 15:12:53 +02:00
Hauke Mehrtens
9c84d619fc ramips: Fix use mac-base for TP-Link TL-MR6400 v4 and v5
Use mac-base for mac-base TP-Link TL-MR6400 v4 and v5

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-16 13:11:08 +03:00
Hauke Mehrtens
ff3d0de095 ramips: Fix wmac dts definition for TP-Link TL-MR6400 v4 and v5
This code assumed that the mt7628an_tplink_8m.dtsi file defines
mediatek,mtd-eeprom for the wmac and sets status to okay.

The mediatek,mtd-eeprom definition was removed in commit e93f41adee
("ramips: convert MT7628 EEPROM to NVMEM format") but the dts for these
two devices was not adapted to include the eeprom position on its own.

The status = "okay" property was removed in 0a1d15642f ("ramips:
mt7628: use nvmem-layout"), but the property was not added to these dts
files.

Without this change wifi does not work for these devices.

Fixes: e93f41adee ("ramips: convert MT7628 EEPROM to NVMEM format")
Fixes: 0a1d15642f ("ramips: mt7628: use nvmem-layout")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-16 13:11:08 +03:00
Martin Schiller
cffd3ad8d7 lantiq: add patch to fix the reset gpio handling in the pci driver
Linux kernel commit 90c2d2eb7ab5 ("MIPS: pci: lantiq: switch to using
gpiod API") not only switched to the gpiod API, but also inverted /
changed the polarity of the GPIO.

According to the PCI specification, the RST# pin is an active-low
signal. However, most of the device trees that have been widely used for
a long time (mainly in the openWrt project) define this GPIO as
active-high and the old driver code inverted the signal internally.

Apparently there are actually boards where the reset gpio must be
operated inverted. For this reason, we cannot use the GPIOD_OUT_LOW/HIGH
flag for initialization. Instead, we must explicitly set the gpio to
value 1 in order to take into account any "GPIO_ACTIVE_LOW" flag that
may have been set.

In order to remain compatible with all these existing device trees, we
should therefore keep the logic as it was before the commit.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
faaa54161e lantiq: dts: add missing irqs to mei node on AmazonSE, Danube and AR9
This adds to missing DyingGasp and USB OC interrupts to the mei node.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
ece380cf28 lantiq: vmmc kernel-in-tree driver: use platform_get_irq to get irqs
This is required for linux-6.1 compatibility.

IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
83fccc42df lantiq: old gptu timer driver: use platform_get_irq to get irqs
This is required for linux-6.1 compatibility.

IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
db4bb19679 lantiq: ifxmips_pcie: use platform_get_irq to get irqs from dts
This is required for linux-6.1 compatibility.

IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
1825ea9098 lantiq: dts: vr9: add missing interrupts to pcie node
This adds the missing interrupts to the pcie node.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
284f12bfa6 lantiq: ifxmips_pcie: use dev_err_probe
Use dev_err_probe() to get rid of the following warning which is
seen when the PCIe PHY has not been probed yet:
pcie-xrx200 1d900000.pcie: failed to get the PCIe PHY

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Hauke Mehrtens
783c3aace2 lantiq: Add some gswip patches
This backports some patches for the gswip switch driver.

I copied them from this repository:
https://github.com/xdarklight/linux/commits/lantiq-gswip-integration-20221022

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[drop some patches which may break functionality at the moment]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Hauke Mehrtens
e79dacd962 lantiq: Fix bug in error handling of timer driver
If the reverted timer driver fails to allocate interrupts handle the
error better.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[moved printk before the cleanup for-loop]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Hauke Mehrtens
a3659b158b lantiq: Refresh patches and configuration
Make all the patches apply and delete the ones already integrated into
upstream Linux kernel. This also refreshes some of the kernel
configurations.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed for linux 6.1.89]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
e692742be7 lantiq: set Linux 6.1 as testing kernel
Add KERNEL_TESTING_PATCHVER for Linux 6.1.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
b704c537cf kernel/lantiq: Restore kernel files for v5.15
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Martin Schiller
2196815961 kernel/lantiq: Create kernel files for v6.1 (from v5.15)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Hauke Mehrtens
494a10964c lantiq: Refresh kernel configuration
This refreshes the configuration for Linux kernel 5.15.

I first selected the xrx200 subtarget and then refreshed the target
kernel configuration using this command:
  make kernel_oldconfig CONFIG_TARGET=target
Then I selected one subtarget after the other and refreshed their
configuration using this command:
  make kernel_oldconfig CONFIG_TARGET=subtarget

I compared the kernel configuration used to compile the kernel from the
build directory for each subtarget before and after this task and it was
still the same.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[refreshed config for linux 5.15.158]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-15 08:54:58 +02:00
Rodrigo Balerdi
0868268c9f
ipq806x: rt4230w-rev6: fix status reporting via the LEDs
There is a custom LED controller between the 3 SoC GPIO outputs and
the red and blue LEDs of the device. It implements a strange mapping
that includes fixed, flashing, and breathing modes.

The current DTS configuration causes OpenWrt to flash the LEDs over
the controller's own flashing, resulting in chaotic output in boot,
failsafe, and upgrade modes.

This change fixes the LEDs in the best way possible as long as each
OpenWrt running state is limited to be signaled by a single led.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15440
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-14 12:22:59 +02:00
Christophe JAILLET
5ac8cf1eab
ag71xx: Slightly simplify 'ag71xx_rx_packets()'
There is no need to use 'list_for_each_entry_safe' here, as nothing is
removed from the list in the 'for' loop.
Use 'list_for_each_entry' instead, it is slightly less verbose.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://github.com/openwrt/openwrt/pull/15435
Link: https://github.com/openwrt/openwrt/pull/15435
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-14 12:21:02 +02:00
Mieczyslaw Nalewaj
1a544dc5ce
generic: 5.15, 6.1: use RTL_8221B_VB_CG_PHYID in Realtek PHY detection
Use the constant RTL_8221B_VB_CG_PHYID instead of a numeric value.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-13 20:27:25 +02:00
Mieczyslaw Nalewaj
76584c798a
generic: 6.6: fix realtek PHY detection patch
Fixes the issue of RTL8221B-VB-CG not being detected correctly.
Reverts changes from f6c27b2, leaving only the read_c45 test.

Fixed: #15093
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-13 20:27:17 +02:00
Daniel Golle
fbf6f9da02 airoha: set KERNEL_TESTING_PATCHVER:=6.6
Lets give Linux 6.6 a try.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-12 12:52:16 +02:00
Daniel Golle
6961d5e9c1 kernel/airoha: refresh config-6.6
Refresh kernel config for Linux 6.6.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-12 12:52:16 +02:00
Daniel Golle
22efab92f5 kernel/airoha: refresh patch on top of Linux 6.6
Refresh the only remaining downstream patch.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-12 12:52:16 +02:00
Daniel Golle
577eaa58da kernel/airoha: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-12 12:52:16 +02:00
Daniel Golle
8ca67645ce kernel/airoha: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15416
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-12 12:52:16 +02:00
Hauke Mehrtens
1fae75ebd9 kernel: bump 5.15 to 5.15.158
Removed because they are upstream:
   generic/backport-5.15/702-v5.19-01-arm64-dts-mediatek-mt7622-add-support-for-coherent-D.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=506ac5538498717fce699feaddb2ed97ae1c3ca7

   generic/backport-5.15/702-v5.19-04-arm64-dts-mediatek-mt7622-introduce-nodes-for-Wirele.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=2f83d3d2cc3c0df89f833cd8c09989187f0c3ce1

Manually adapted:
   generic/pending-5.15/680-NET-skip-GRO-for-foreign-MAC-addresses.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-12 12:16:18 +02:00
Stefan Kalscheuer
4b30c2ff0f mvebu: switch to kernel 6.6
Update default kernel version to 6.6 and drop configs and patches for
kernel 6.1. We can also omit the conditional to include DTS dir.

Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/15449
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-12 11:29:23 +02:00
Robert Marko
dc9220f748 ipq40xx: fixup remaining devices that dont use QCA807x PHY
Like AVM 1200 these devices also do not use QCA807x PHY at all and thus
they disables all of the individual PHY nodes, however this is not enough
anymore since the conversion to PHY package.

Now its now enough to disable the PHY-s in the package alone, but the PHY
package node itself must also be disabled.

Fixes: 1b931c33a2 ("ipq40xx: adapt to new Upstream QCA807x PHY driver")
Link: https://github.com/openwrt/openwrt/pull/15444
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-12 10:56:16 +02:00
INAGAKI Hiroshi
61e8728d86 ramips: add support for ELECOM WMC-S1267GS2
ELECOM WMC-S1267GS2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) mesh extender,
based on MT7621A.

This device has almost the same hardware as WMC-M1267GST2.

Specification:

- SoC          : MediaTek MT7621A
- RAM          : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash        : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN         : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet     : 10/100/1000 Mbps x4
  - switch     : MediaTek MT7530 (SoC)
- LEDs/Keys    : 6x/6x
- UART         : through-hole on PCB ("J4")
  - arrangement: 3.3V, GND, TX, RX from tri-angle marking
  - settings   : 57600n8
- Power        : 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WMC-S1267GS2 normally
2. Set IP address of the computer to 192.168.2.x
3. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用") button
5. Wait ~120 seconds to complete flashing

MAC addresses:

LAN    : 04:AB:18:xx:xx:9E (Factory, 0xFFF4 (hex))
2.4 GHz: 04:AB:18:xx:xx:9F
5 GHz  : 04:AB:18:xx:xx:A0 (Factory, 0x4 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-11 19:33:28 +02:00
INAGAKI Hiroshi
927a77ecff ramips: add support for ELECOM WMC-M1267GST2
ELECOM WMC-M1267GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) mesh router,
based on MT7621A.

Specification:

- SoC          : MediaTek MT7621A
- RAM          : DDR3 256 MiB (Nanya NT5CC128M16JR-EK)
- Flash        : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN         : 2.4/5 GHz 2T2R (MediaTek MT7615D)
- Ethernet     : 10/100/1000 Mbps x5
  - switch     : MediaTek MT7530 (SoC)
- LEDs/Keys    : 6x/6x
- UART         : through-hole on PCB ("J4")
  - arrangement: 3.3V, GND, TX, RX from tri-angle marking
  - settings   : 57600n8
- Power        : 12 VDC, 1 A

Flash instruction using factory image:

1. Boot WMC-M1267GST2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC addresses:

LAN    : 04:AB:18:xx:xx:61 (Factory, 0xFFF4 (hex))
WAN    : 04:AB:18:xx:xx:62 (Factory, 0xFFFA (hex))
2.4 GHz: 04:AB:18:xx:xx:63
5 GHz  : 04:AB:18:xx:xx:64 (Factory, 0x4 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2024-05-11 19:33:28 +02:00
Hauke Mehrtens
84d0b0b925 kernel: bump 5.15 to 5.15.157
Removed because they are upstream:
   generic/backport-5.15/741-v6.9-01-netfilter-flowtable-validate-pppoe-header.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=d06977b9a4109f8738bb276125eb6a0b772bc433

Removed because they are upstream:
   generic/backport-5.15/741-v6.9-02-netfilter-flowtable-incorrect-pppoe-tuple.patch
   https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=e719b52d0c56989b0f3475a03a6d64f182c85b56

Manual adapted the following patches:
   generic/pending-5.15/700-netfilter-nft_flow_offload-handle-netdevice-events-f.patch
   generic/pending-5.15/723-net-mt7531-ensure-all-MACs-are-powered-down-before-r.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-11 18:30:30 +02:00
Hauke Mehrtens
1fbe41f489 kernel: bump 5.15 to 5.15.156
No manual changes needed.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-05-11 18:30:30 +02:00
Sheng Huang
985af21123 ramips: add support for JDCloud RE-CP-02
- Soc: MediaTek MT7621AT
- RAM: 512 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7905DAN, MediaTek MT7975DN
- Ethernet: 1 WAN, 3 LAN (Gigabit)
- Buttons: Reset, Joylink
- LEDs: (red, blue, green), routed to one indicator in the top of the
  device
- Power: DC 12V 1A tip positive
- 1 TF Card Slot

The pins for the serial console are already labeled on the board
J4(V, R, T, G). Serial settings: 3.3V, 115200

MAC addresses:

|         | MAC               | Algorithm |
| ------- | ----------------- | --------- |
| label   | dc:d8:xx:xx:xx:01 | label     |
| LAN     | dc:d8:xx:xx:xx:01 | label     |
| WAN     | dc:d8:xx:xx:xx:02 | label+1   |
| WLAN 2g | dc:d8:xx:xx:xx:03 | label+2   |
| WLAN 5g | de:d8:xx:xx:xx:04 | label+3   |

1. rename the
   openwrt-ramips-mt7621-jdcloud_re-cp-02-squashfs-sysupgrade.bin
   to JDCOS.bin

2. start a TFTP server from IP address 192.168.68.10 and serve the
   image named JDCOS.bin

3. connect your device to the LAN port

4. power up the router and press any key on the console to interrupt
   the boot process.

5. enter the following commands on the router console

   1. setenv bootcount 6

   2. saveenv

   3. reset

      > NOTE: wait for the restart, it will automatically fetch the
      > image named JDCOS.bin from the TFTP server and write it into
      > the flash. After the writing is completed, the router will be
      > automatically restarted.

Unable to recognize large-capacity TF card, see #14042. But the patch
https://github.com/openwrt/openwrt/issues/14042#issuecomment-1910769942
works

Co-Authored-By: Jianti Chen <clbcjt@outlook.com>
Signed-off-by: Sheng Huang <shenghuang147@gmail.com>
2024-05-11 17:24:10 +02:00
Leon M. Busch-George
20e4a18feb mediatek: filogic: add support for Cudy M3000 v1
Hardware:
  SoC:     MT7981b
  RAM:     256 MB
  Flash:   128 MB SPI NAND
  Ethernet:
    1x 2.5Gbps (rtl8221b)
    1x 1Gbps (integrated phy)
  WiFi:    2x2 MT7981
  Buttons: Reset, WPS
  LED:     1x multicolor

Solder on UART:
  - remove rubber ring on the bottom
  - remove screws
  - pull up the cylinder, maybe help by push on an ethernet socket with a screwdriver
  - remove the (3) screws holding the board in the frame
  - remove the board from the frame to get to the screws for the silver, flat heat shield
  - remove the (3) screws holding the heat shield
  - solder UART pins to the back of the board
    - make sure to have the pins point out on side with the black, finned heat spread
    - the markings for the pins are going to be below the silver heat shield
    - Vcc is not needed

If you don't intend on using the UART outside of the installation process, you might not
want to solder:

  - carefully scrape off the thin layer of epoxy on the holes (not the copper)
  - place your pin header with the UART attached in the holes
  - the pins, starting with the one closest to the socket:
    - Vcc (not required)
    - GND
    - RX
    - TX
  - either wedge the header or hold it with your fingers so that the pins stay in contact with the board

Installation (UART):
  - attach an Ethernet cable to the 1Gbps port (black) on the router
  - hold the reset button while powering the router
  - press CTRL-C or wait for the timeout to get to the U-Boot prompt
  - prepare a TFTP server on the network to supply ..-initramfs-kernel.bin
  - use 'tftpboot' in the U-Boot shell to pull the image
  - boot the image using 'bootm'
  - push the ..-sysupgrade to the router using your preferred method
  - perform the upgrade with 'sysupgrade -n'

There is a recovery mechanism that involves fetching a file called 'recovery.bin' but that is not understood yet.

Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
2024-05-11 17:18:51 +02:00
Kevin Abraham
1045bd4a04 uboot-envtools: ath79: remove env config for Senao Loader devices
uboot-envtools can automatically parse the 'u-boot,env' compatible string from the dts.

Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
2024-05-11 16:57:28 +02:00
Kevin Abraham
1dd036a659 ath79: add support for Senao Engenius ENS1750
FCC ID: A8J-EWS660AP

Engenius ENS1750 is an outdoor wireless access point with
2 gigabit ethernet ports, dual-band wireless,
internal antenna plates, and 802.3at PoE+

Engenius EWS660AP, ENS1750, and ENS1200 are "electrically identical,
different model names are for marketing purpose" according to docs
provided by Engenius to the FCC.

**Specification:**

  - QCA9558 SOC		2.4 GHz, 3x3
  - QCA9880 WLAN	mini PCIe card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - AR8033 PHY		SGMII GbE with PoE+ OUT
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM
  - UART at J1		populated, RX grounded
  - 6 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, eth1, 2G, 5G) (reset)

**MAC addresses:**

  Base MAC addressed labeled as "MAC"
  Only one Vendor MAC address in flash

  eth0 *:d4 MAC art 0x0
  eth1 *:d5 --- art 0x0 +1
  phy1 *:d6 --- art 0x0 +2
  phy0 *:d7 --- art 0x0 +3

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs.bin to '0101A8C0.img'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

**Format of OEM firmware image:**

  The OEM software of ENS1750 is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-ens1750-uImage-lzma.bin
    openwrt-ar71xx-generic-ens1750-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Tested-by: Kevin Abraham <kevin@westhousefarm.com>
Signed-off-by: Kevin Abraham <kevin@westhousefarm.com>
2024-05-11 16:57:28 +02:00
Daniel Golle
8113169cad mediatek: fix PWM fan on BPi-R4
Add additional PWM fan cooling step and enable fan on BPi-R4.

Suggested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-11 00:52:34 +01:00
Álvaro Fernández Rojas
72cdba7b1a kernel: add missing kernel 6.6 symbols
Add missing kernel 6.6 symbols for bcm27xx.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-05-10 21:02:24 +02:00
Kevin Jilissen
5a5c52085a realtek: Trap LLDP packets to the CPU
We should setup the registers for trapping LLDP packets to the CPU.
Currently, these packets are forwarded to all ports which is not desired
behaviour.

Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
2024-05-10 16:03:51 +02:00
Kevin Jilissen
81ab9ef2d1 realtek: Change LLTP register to LLDP
These registers control the handling of Link Layer Discovery Protocol
(LLDP) packets. This seems to be a typo in the naming.

Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
2024-05-10 16:03:51 +02:00
Eros Brigmann
803c00e9b8 ramips: add support for Wavlink WL-WN531G3
This device is similiar to the Wavlink WL-WN531A3.
Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 external antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button
  - 1x Turbo button
  - 1x Wps button
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 5x Blue leds (ethernet ports)
  - 1x Power led
  - 1x Wifi led
UART:
  - 57600-8-N-1
Everything works correctly.

Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
In my case the whole device was locked and there was no way
to flash the image, except for flashing directly to the flash
via an spi-flasher. You need to put the sysupgrade image file at
the beginning of 0x60000.

Notes
-----
1) Router mac addresses:
   LAN XX:XX:XX:XX:XX:F0 (factory @ 0x28)
   WAN XX:XX:XX:XX:XX:F1 (factory @ 0x2e)
   WIFI 2G XX:XX:XX:XX:XX:F2 (factory @ 0x04)
   WIFI 5G XX:XX:XX:XX:XX:F3 (factory @ 0x8004)

   LABEL XX:XX:XX:XX:XX:F2

Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
2024-05-10 00:05:25 +02:00
Shiji Yang
eb48dae81e ath79: enable 6.6 testing kernel
The ath79 target now supports the vanilla 6.6 kernel. Enjoy it!

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:53:02 +02:00
Shiji Yang
26390b5361 ath79: skip reset control for syscon devices
Fix the issue of exclusive reset controller acquisition failure on
kernel 6.6.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:53:02 +02:00
Shiji Yang
e938d68074 ath79: refresh 6.6 kernel config files
All kernel config files are refreshed by
`make kernel_oldconfig CONFIG_TARGET={subtarget_target,subtarget}`

"CONFIG_SQUASHFS_DECOMP_SINGLE=y" is manually selected as all ath79
SoCs are single core processors.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:53:02 +02:00
Shiji Yang
872fe7e9f9 ath79: refresh 6.6 kernel patches
Some APIs have been changed. Porting them to the new kernel 6.6
version to fix the compile error.

Removed upstreamed:
	010-v6.4-gpio-ath79-Convert-to-immutable-irq_chip.patch[1]

Manually rebased:
	700-phy-add-ath79-usb-phys.patch
	721-phy-mdio-bitbang-prevent-rescheduling-during-command.patch. ref:[2]

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.6.y&id=b11ce7e48121a02ceedec9f4dfcab4f2bee8f35f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-6.6.y&id=002dd3de097c778a74ae9e47e598bea6ad055af0

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:53:02 +02:00
Shiji Yang
d123330aa9 ath79: restore kernel 6.1 config files and patches
Copy patches and kernel configs from kernel 6.6 to restore the
default 6.1 kernel support files.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:53:02 +02:00
Shiji Yang
7d01a0b436 ath79: rename patches directory and kernel config from 6.1 to 6.6
This is preparation for 6.6 kernel support. Renaming files allows
us to better track their git history.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:53:01 +02:00
Shiji Yang
e155e3bd09 ath79: add MikroTik suffix to the local GPIO latch driver
The upcoming 6.6 kernel will introduce a new upstream generic
"gpio-latch" driver. It will conflict with the downstream MikroTik
GPIO latch driver. Let's rename it to avoid any potential issues.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:51:14 +02:00
Shiji Yang
24693ac7e5 ath79: fix build error for downstream gpio drivers
Initialize fwnode instead of the deprecated of_node.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-05-09 23:51:14 +02:00
Luis Mita
63b8d98dd0 mediatek: add support for Cudy TR3000 v1
Hardware:
 - SoC: MediaTek MT7981B
 - CPU: 2x 1.3 GHz Cortex-A53
 - Flash: 128 MiB SPI NAND
 - RAM: 512 MiB
 - WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
 - Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
 - USB 3.0 port
 - Buttons: 1 Reset button, 1 slider button
 - LEDs: 1x Red, 1x White
 - Serial console: internal test points, 115200 8n1
 - Power: 5 VDC, 3 A

MAC addresses:
+---------+-------------------+-----------+
|         | MAC               | Algorithm |
+---------+-------------------+-----------+
| WAN     | 80:af:ca:xx:xx:x1 | label+1   |
| LAN     | 80:af:ca:xx:xx:x0 | label     |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label     |
| WLAN 5g | 82:af:ca:xx:xx:x0 |           |
+---------+-------------------+-----------+

Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.

To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.

setenv bootfile initramfs-kernel.bin
tftpboot
bootm

6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.

Signed-off-by: Luis Mita <luis@luismita.com>
2024-05-09 23:32:32 +02:00
Alan Luck
30e8fd73ec ramips: Add support for D-Link DIR-2150-A1
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset

MAC Table
Label xx:xx:xx:xx:xx:EB
LAN xx:xx:xx:xx:xx:EB
2.4Ghz xx:xx:xx:xx:xx:EC
5Ghz xx:xx:xx:xx:xx:ED
WAN xx:xx:xx:xx:xx:EE

Flash instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image

D-Link Recovery GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload the recovery.bin to the device

Firefox on Windows in a Private Window (incognito) works me
Internet Explorer mode in Microsoft Edge works for others
seems to not work in Linux or virtual machine on Linux for most
some see success using 'curl -v -i -F "firmware=@file.bin" 192.168.0.1'

Thanks to @frkca and @rodneyrod for testing and pushing for its creation

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
2024-05-09 22:28:23 +02:00
Mieczyslaw Nalewaj
474b108dfe ramips: use led, function/color syntax for some tp-link archer routers
Setting the LED name and abandoning the label and using the
function/color syntax for some TP-Link Archer series routers:
Archer C2 v1, Archer C20 v1, Archer C20i and Archer C50 v1

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-09 22:24:48 +02:00
Mieczyslaw Nalewaj
d646ea8a00 ramips: use function/color syntax for some dlink dir routers
Abandoning the label and using the function/color syntax for some dlink
dir series routers: dir-1960-a1, dir-2660-a1, dir-2640-a1, dir-3040-a1
and dir-3060-a1

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-09 22:24:31 +02:00
Mieczyslaw Nalewaj
8d7fa09181 ramips: rename include file to a more suitable name
Rename from mt7621_dlink_dir-xx60-a1.dtsi to mt7621_dlink_dir_nand_128m.dtsi
and associated group name when creating the mt7621.mk image

Co-authored-by: Alan Luck <luckyhome2008@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-09 22:21:39 +02:00
Mieczyslaw Nalewaj
9dae0ac0bc mediatek: correct address of MT753x switch IC
Continuation of commit 8b66f1a. Set the switch address on the MDIO bus to 31.
This is required for all boards currently working with the mt7530 DSA driver.

Fixes: #15419
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-05-09 19:43:54 +02:00
Christian Marangi
9001014a24
generic: 6.6: backport patch adding support for rgmii-id in stmmac-ipq806x
Backport patch merged upstream for rgmii-id support in stmmac-ipq806x.

This is needed for some device that directly connets PHY to the gmac
port and require rgmii-id phy-modes.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-09 16:48:34 +02:00
Tianling Shen
0341a06f1f rockchip: switch to kernel 6.6
Switch to Linux kernel version 6.6 and drop configs, files and patches
for Linux 6.1.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-05-09 10:43:37 +02:00
Robert Marko
592b6aabca ipq40xx: wpj419: use existing label for SPI node
WPJ419 is still manually defining SPI node, so lets
convert it to use the existing upstream labels for SPI node.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:44 +02:00
Robert Marko
c9743030e3 ipq40xx: wpj419: use existing label for pinctrl node
WPJ419 is still manually defining pinctrl node, so lets
convert it to use the existing upstream labels for pinctrl node.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:44 +02:00
Robert Marko
1f3fe4662e ipq40xx: wpj419: use existing label for PCIe node
WPJ419 is still manually defining PCIe node, so lets
convert it to use the existing upstream labels for PCIe node and while we
are here use the -gpios suffix instead.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:44 +02:00
Robert Marko
63c5d8bd72 ipq40xx: use existing labels for MDIO node
Some boards are still defining MDIO nodes under soc instead of using the
existing upstream labels to reference them so convert them.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:44 +02:00
Robert Marko
90f9bc799f ipq40xx: use existing labels for I2C nodes
Some boards are still defininig I2C nodes under soc instead of using the
existing upstream labels to reference them so convert them.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:44 +02:00
Robert Marko
625e912d75 ipq40xx: use existing labels for UART nodes
Some boards are still defininig UART nodes under soc instead of using the
existing upstream labels to reference them so convert them.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:43 +02:00
Robert Marko
7359362a2e ipq40xx: ncp-hg100-cellular: drop QPIC BAM node
This device does not have NAND enabled at all and NAND is the only consumer
of QPIC BAM DMA, so drop the node.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:43 +02:00
Robert Marko
b475e8f717 ipq40xx: wpj419: use existing labels for DMA nodes
WPJ419 is still manually defining dma nodes(And even some labels), so lets
convert it to use the existing upstream labels for DMA nodes.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:43 +02:00
Robert Marko
e54c9c156b ipq40xx: use existing labels for crypto node
Currently, a lot of boards are still not using the existing label to
reference the crypto node, so lets rectify this.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:43 +02:00
Robert Marko
22e96cc3ff ipq40xx: use existing labels for prng node
Currently, a lot of boards are still not using the existing label to
reference the prng node, so lets rectify this.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:43 +02:00
Robert Marko
2e94536fc8 ipq40xx: use existing labels for watchdog node
Currently, a lot of boards are still not using the existing label to
reference the watchdog node, so lets rectify this.

Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-09 10:11:43 +02:00
Daniel Golle
3f4347fce0 mediatek: mt7988a.dtsi: add interrupts to GE switch PHYs
The way to register the switch MDIO bus and PHYs on the bus in upstream
Linux is more strict and requires each PHY to explicitely state the
interrupt instead of assuming it in case the 'interrupts' property in DT
is missing.

Add missing interrupts for the PHYs of the build-in 4x1GE switch of the
MT7988 SoC.

Fixes: 4354b34f6f ("generic: 6.6: sync mt7530 DSA driver with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-08 22:19:26 +01:00
Magnus Lindström
54abf1cfc7 mediatek: ASUS TUF-AX6000: fix phy-handle numbering
To fix issue #15304
Correct br-lan ports 1-4 so that phy-handle matches reg nr not port label.

Fixes: eb13076e77 ("mediatek: fix DTS defining mt7530 switch phys but not referencing them")
Signed-off-by: Magnus Lindström <magnus1089@hotmail.com>
2024-05-08 22:19:09 +01:00
Linus Walleij
51e9aa6ace gemini: Bump to kernel v6.6
The Gemini works fine with kernel v6.6.

As per the example for ipq806x, drop support for anything
older than v6.6, there is no point in supporting it,
and the new DTS SoC directory just makes it hard to
maintain.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-08 16:57:32 +02:00
Daniel Golle
0d74b2a1e5 generic: 6.1, 6.6: replace Airoha EN8811H PHY driver with upstream
Backport driver from upcoming Linux 6.10 and put a pending fix on top
to make sure the netdev trigger offloading behaves as expected.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-08 01:54:32 +01:00
Mathew McBride
683355d0a6 armsr: armv8: enable serial console for Renesas platforms
Support for Renesas Arm families was added in commit 1ff4f4df23
("armsr: armv8: enable CONFIG_ARCH_RENESAS"), but this did not
enable the console/tty hardware for these SoCs, which is derived
from the SuperH family (CONFIG_SERIAL_SH_SCI).

Link: https://github.com/openwrt/openwrt/issues/15284
Signed-off-by: Mathew McBride <matt@traverse.com.au>
2024-05-07 13:01:20 +01:00
Mathew McBride
ffbc4c897f base-files: armsr: add script to migrate GPIO switches on Ten64 board
Due to a change in kernel 6.2, the GPIO numbers on certain
architectures (including arm64) have changed. This script
will update any defined GPIO switches to the new numbering.

See https://lists.openwrt.org/pipermail/openwrt-devel/2024-March/042448.html
for more information.

In the future, the GPIO switch mechanism will likely be
replaced with something using libgpiod.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2024-05-07 13:01:20 +01:00
Mathew McBride
5f609d8960 base-files: armsr: number Ten64 GPIOs according to kernel version
A change in kernel 6.2[1] caused the base numbers of GPIOs to
change significantly on some architectures like aarch64.

We have to number our GPIOs accordingly.
Ideally the board.d scripts should look through sysfs
to find the basenum (like cat "/sys/devices/platform/soc/2000000.i2c/
i2c-0/0-0076/gpio/gpiochip640/base"), but the problem is
that this occurs before modules are loaded, meaning I2C and other
runtime devices may be missing.

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] https://lore.kernel.org/lkml/cover.1662116601.git.christophe.leroy@csgroup.eu/T/
2024-05-07 13:01:19 +01:00
Mathew McBride
c8927d7c01 armsr: armv8: add new fsl-enetc-core module for kernel 6.6
From kernel 6.3 onwards, the fsl-enetc driver has restructured
it's common code into a 'core' module[1].

Signed-off-by: Mathew McBride <matt@traverse.com.au>

[1] https://patchwork.kernel.org/project/netdevbpf/patch/20230119160431.295833-2-vladimir.oltean@nxp.com/
2024-05-07 13:01:19 +01:00
Mathew McBride
5744205eb6 armsr: add kernel 6.6 as a testing target
Add kernel 6.6 for testing.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2024-05-07 13:01:19 +01:00
Mathew McBride
fb29f702af kernel/armsr: add config stubs and changes needed for 6.6
Introduce new configuration options prompted by 6.6 (relative to 6.1).
The kernel arm64 defconfig is used as guide for 'core' options, while
video/camera/other media drivers are turned off by default.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2024-05-07 13:01:19 +01:00
Mathew McBride
587b8b8e32 kernel/armsr: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.

See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2024-05-07 13:01:19 +01:00
Mathew McBride
f125e38ced kernel/armsr: Add configuration files and patches for v6.6
Based on the 6.1 files, but without any 6.6 additions.

Signed-off-by: Mathew McBride <matt@traverse.com.au>
2024-05-07 13:01:19 +01:00
Mieczyslaw Nalewaj
bd6852185b
ipq806x: swap lan leds for Meraki MR52
LAN Leds on Meraki MR52 are wrong and needs to be swapped to actually
reflect real ports (lan1<->lan2).

Fixes: #15388
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15410
[ wrap commit to 80 columns and improve commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-07 13:35:49 +02:00
Daniel Golle
50f7155d57 generic: 6.1, 6.6: move accepted patches to backport folders
Move two accepted patches for the mt7530 DSA driver from pending to
accepted.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-07 12:21:12 +01:00
Felix Fietkau
a7ae4ed0a3 kernel: fix tools build breakage on macos with x86
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-07 12:50:27 +02:00
Felix Fietkau
931b2bafa7 mediatek: fix mt7988a pmu interrupt dts property
Fixes profiling using perf

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-07 12:50:27 +02:00
Stijn Tintel
a9781a04a1 realtek: add RTL821X_CHIP_ID
According to the Realtek SDK code, the RTL8214FC, RTL8218B and RTL8218FB
all have the same chip ID 0x6276. Let's add a constant for it, as we're
using it in more than one location.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2024-05-07 12:27:33 +03:00
Stijn Tintel
1626b06683 realtek/rtl839x: respect phy-is-integrated property
Respect the phy-is-integrated property on ethernet-phy nodes.

There are RTL8393M switches where the PHYs at address 48 and 49 are
provided by an external RTL8214FC. Hardcoding them to use the internal
SerDes makes it impossible to use the ports connected to such an
external PHY. Respect the phy-is-integrated property on ethernet-phy
nodes as a first step to support such ports.

The potential impact for this should be limited to RTL8393 based
switches, and looking at the commit messages and device tree files of
the supported switches based on this SoC, the SFP and/or combo ports are
either not working (D-Link DGS-1210-52, Netgear GS750E, TP-Link
SG2452P/T1600G-52PS), use PHYs at a different address (Panasonic
SwitchM48EG PN28480K), or already have the phy-is-integrated property
set on the PHYs at address 48 and 49.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
2024-05-07 12:27:30 +03:00
Martin Schiller
3dde786163 mediatek: bpi-r4: fix uci-default script for mac storage
There was a typo in commit 5709254690 ("mediatek: bpi-r4: store random
MAC addresses for the BPi-R4"). Let's fix it and also add support for
the bpi-r4-poe variant.

Fixes: 5709254690 ("mediatek: bpi-r4: store random MAC addresses for the BPi-R4")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-07 09:56:36 +01:00
Martin Schiller
738b427d35 mediatek: bpi-r4: add rootwait to bootargs
In commit cd4de3251c ("mediatek: wait for fitblk rootfs"), the linux
6.6 files and patches has been forgotton to be fixed.

Fixes: cd4de3251c ("mediatek: wait for fitblk rootfs")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-07 09:56:36 +01:00
Martin Schiller
8c1250cb39 mediatek: bpi-r2: add rootwait to bootargs
In commit cd4de3251c ("mediatek: wait for fitblk rootfs"), the linux
6.6 files and patches has been forgotton to be fixed.

Fixes: cd4de3251c ("mediatek: wait for fitblk rootfs")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-07 09:56:36 +01:00
Antonio Flores
ce4da3cf41 rockchip: add kernel 6.6 as testing kernel
Add kernel 6.6 as testing kernel

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-07 00:17:12 +02:00
Antonio Flores
e18dda0159 kernel: add missing kernel 6.6 symbols
Add missing kernel 6.6 symbols

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-07 00:17:12 +02:00
Antonio Flores
83edd39db6 rockchip: refresh config 6.6
Refresh config 6.6 (make kernel_oldconfig).

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-07 00:17:12 +02:00
Antonio Flores
728db5ec05 rockchip: refresh 6.6 patches
Refresh kernel 6.6 patches.
Removed backpored patches.

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-07 00:17:12 +02:00
Antonio Flores
dcd2367349 kernel/rockchip: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.

See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-07 00:17:12 +02:00
Antonio Flores
ddfd526140 kernel/rockchip: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-07 00:17:12 +02:00
Tony Ambardar
708e6b840e kselftests-bpf: update for kernel 6.6
Enable building multiple test programs and related kernel modules, with
initial support for the bpf_testmod.ko module required since kernel 6.4.
Explicitly disable LTO and clean up makefile variables and formatting.

Fix a musl-related build failure by adding a kernel 6.6 patch:

     360-selftests-bpf-portability-of-unprivileged-tests.patch

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2024-05-06 22:39:18 +02:00
Daniel Golle
0b0e3e22f8 mediatek: bpi-r4: add ethernet aliases to DT
Adding the aliases also for Linux 6.6 was forgotten and is required for
U-Boot to hand down persistent MAC addresses to Linux.

Fixes: 5709254690 ("mediatek: bpi-r4: store random MAC addresses for the BPi-R4")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-06 16:38:44 +01:00
Corey Minyard
226b15f885
ipq40xx: Enable the Engenius EAP1300
Now that DSA is enabled and the MAC addresses are set properly, we can
use it.

Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-06 12:45:53 +02:00
Corey Minyard
63b1326575
ipq40xx: Properly set MAC addresses for the EAP1300
The code that was there was just taking whatever was left in the
registers, which was just wrong.  Set the addresses using the value from
the u-boot environment, the same way the OEM firmware does.

Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-06 12:45:53 +02:00
Corey Minyard
e0567456bf
ipq40xx: convert Engenius EAP1300 to DSA
This commit converts the EAP1300 to DSA setup.

Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-06 12:45:52 +02:00
Corey Minyard
e51791963e
ipq40xx: Enable NVMEM_U_BOOT_ENV config
It's needed to get the MAC addresses for the Engenius EAP1300.

Signed-off-by: Corey Minyard <minyard@acm.org>
Link: https://github.com/openwrt/openwrt/pull/15358
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-06 12:45:51 +02:00
Christian Marangi
f3f3e2c5bb
ipq4019: fix even more wrong reference to USB node
Commit 6136ebabc5 ("ipq40xx: 6.6: fix DTS to use reference for usb
node") fixed only some of the reference to USB node but many others were
still using the old broken usb3/usb2. Fix every reference to those node
and move them on using the tag name.

Fixes: 6136ebabc5 ("ipq40xx: 6.6: fix DTS to use reference for usb node")
Link: https://github.com/openwrt/openwrt/pull/15392
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-05-06 12:40:24 +02:00
Rany Hany
8607372b41 mediatek: fix broken PCIe caused by update to 6.6.30
The patch "710-pci-pcie-mediatek-add-support-for-coherent-DMA.patch"
makes use of "syscon_regmap_lookup_by_phandle" which requires that
"syscon" be in the compatible list.

Without this patch, PCIe probe will fail with the following error:

[    1.287467] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[    1.294019] mtk-pcie 1a143000.pcie: Parsing ranges property...
[    1.299901] mtk-pcie 1a143000.pcie:      MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[    1.307954] mtk-pcie 1a143000.pcie: missing hifsys node
[    1.313185] mtk-pcie: probe of 1a143000.pcie failed with error -22

Fixes: 4c6e9a9943 ("kernel: bump 6.6 to 6.6.30")
Signed-off-by: Rany Hany <rany_hany@riseup.net>
2024-05-06 11:05:03 +02:00
Martin Schiller
fa804f7d0e mediatek: bpi-r4: add support for 2.5GE PoE variant
This adds support for the bpi-r4 variant with internal 2.5G PHY and
additional ethernet port instead of second sfp.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-06 09:12:05 +02:00
Martin Schiller
14955dcb7e mediatek: bpi-r4: dts: move common parts to dtsi file
Move the common parts of the mt7988a-bananapi-bpi-r4.dts to a dtsi file.
This is done to prepare support for the 2.5G Ethernet Variant.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2024-05-06 09:12:05 +02:00
John Audia
485afd4b11 x86: generic: config-6.6: add/remove default syms
Add new default and remove deprecated symbol introduced by 6.6.30[1]

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v6.6.30&id2=v6.6.29

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-05-05 21:22:31 +02:00
John Audia
4c6e9a9943 kernel: bump 6.6 to 6.6.30
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.30

Removed upstreamed:
	ipq806x/patches-6.6/130-mtd-rawnand-qcom-Fix-broken-misc_cmd_type-in-exec_op.patch[1]

Manually rebased:
	generic/pending-6.6/760-net-core-add-optional-threading-for-backlog-processi.patch
	mediatek/patches-6.6/941-arm64-dts-mt7986-move-cpuboot-in-a-dedicated-node.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.30&id=87fc30db0a2bb300de289dae7c5579cc27a3cbbd

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, flogic/glinet_gl-mt6000
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3, flogic/glinet_gl-mt6000

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-05-05 21:22:31 +02:00
Felix Fietkau
ccb2390d4f kernel: fix corrupted ethernet header on bridge multicast-to-unicast
Fixes: 45a8e962a5 ("kernel: fix crash with multicast-to-unicast and fraglist GRO")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-05 20:49:27 +02:00
Robert Marko
d1504a1e76 ath79: refresh patches
CI is telling us that we need to refresh the patches, so lets do so.

Link: https://github.com/openwrt/openwrt/pull/15382
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-05 11:27:18 +02:00
Rodrigo Balerdi
6dc751815b ipq40xx: merge DTS for Linksys WHW03 V1 and V2
No changes other than the merging itself are intended in this commit.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-05 10:33:13 +02:00
Rodrigo Balerdi
5ac0615b7e ipq40xx: clean up Linksys WHW03 V2 DTS
Apply stylistic changes to facilitate DTS merging with WHW03 V1.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-05 10:33:13 +02:00
Rodrigo Balerdi
c904875562 ipq40xx: add support for Linksys WHW03 V1
Hardware:
=========
SOC:             Qualcomm IPQ4019
WiFi 1:          QCA4019 IEEE 802.11b/g/n
WiFi 2:          QCA4019 IEEE 802.11a/n/ac
WiFi 3:          QCA9886 IEEE 802.11a/n/ac
Bluetooth:       Qualcomm CSR8510 (A10)
Zigbee:          Silicon Labs EM3581 NCP + Skyworks SE2432L
Ethernet:        Qualcomm Atheros QCA8072 (2-port)
Flash:           Samsung KLM4G1FEPD (4GB eMMC)
RAM (NAND):      512MB
LED Controller:  NXP PCA9633 (I2C)
Buttons:         Single reset button (GPIO).

Ethernet:
=========
The device has 2 ethernet ports, configured as follows by default:
- left port: WAN
- right port: LAN

Wifi:
=====
The Wifi radios are turned off by default. To configure the router,
you will need to connect your computer to the LAN port of the device.

Bluetooth and Zigbee:
=====================
Configuration included but not tested.

Storage:
========
For compatibility with stock firmware, all of OpenWrt runs in a 136 MiB
eMMC partition (of which there are two copies, see below). You can also
use partition /dev/mmcblk0p19 "syscfg" (3.4 GiB) any way you see fit.
During very limited tests, stock firmware did not mount this partition.
However, backing up its stock content before use is recommended anyway.

Firmware:
=========
The device uses a dual firmware mechanism: it automatically reverts to
the previous firmware after 3 failed boot attempts.

You can switch to the inactive firmware copy by changing the "boot_part"
U-Boot environment variable. You can also do it by turning on the device
for a couple of seconds and then back off, 3 times in a row.

Installation:
=============
OpenWrt's "factory" image can be installed via the stock web UI:
1. Login to the UI. (The default password is printed on the label.)
2. Enter support mode by clicking on the "CA" link at the bottom.
3. Click "Connectivity", "Choose file", "Start", and ignore warnings.

This port is based on work done by flipy (https://github.com/flipy).

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15345
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-05 10:33:13 +02:00
Antonio Flores
4ebcc5375a rockchip: add Bananapi-R2 Pro board support
Hardware spec:

- Rockchip RK3568 Quad-core ARM Cortex-A55 CPU 2GHz
- GPU Mali-G52 1-Core-2EE OpenGL ES3.2 Vu1kn 1.1 OpenCL 2.0
- Memory2G DDR3 SDRAM (option 4G)
- Storage Onboard 16GB eMMC Flash, Micro SD-Card slot, SATA 3.0 Port,SPI flash
- Network 5 x 10/100/1000 Mbit/s Ethernet MT7531
- Display 1 HDMI port, 2 DSI interface(1 DSI can change to LVDS by software)
- Camera 1 CSI camera interface
- Audio Output HDMI & I2S & Speaker & Headphone
- USB port USB 3.0 PORT (x2), micro USB OTG (x1)
- PCIE 1 mini pcie interface & 1 M.2 key-e interface
- Remote IR Receiver (x1)
- GPIO 40 Pin Header : GPIO (x28) and Power (+5V, +3.3V and GND).
- Switches Reset button, Power button, U-boot button
- LED Power Status
- Power Source 12 volt 2A via DC Power

Installation:

Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
Boot from the SD card
1-hold down the MaskRom button
2-Connect DC power
3-Wait 5 seconds, release the button.

eMMC Installation:

1-Uncompress the OpenWrt sysupgrade image
2-fash to eMMC
dd if=openwrt-rockchip-armv8-sinovoip_bpi-r2-pro-squashfs-sysupgrade.img of=/dev/mmcblk1
sync
3-remove SD card
reboot

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-05 00:46:48 +02:00
Antonio Flores
298e11e43d rockchip: enable MT7531 and RTC drivers
This patch enable MT7531 switch and RTC drivers for BPI-R2 Pro.

Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-05-05 00:46:48 +02:00
Daniel Golle
d9d7286279 rockchip: add driver for hardware RNG
Rockchip SoCs used to have a random number generator as part of their
crypto device, and support for it has to be added to the corresponding
driver.

Newer Rockchip SoCs like the RK3568 have an independent True Random
Number Generator device. Import pending patchset which adds a driver for
it, include it in Kconfig and enable it in the device tree.

Doing so significantly reduces the time needed to boot devices based on
those SoCs, from about 27 seconds until Ethernet is up and running to
less than 13 seconds with a minimal snapshot image.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-04 13:59:48 +01:00
Weijie Gao
7fcb82665e loongarch64: new target
Add target for Loongson LoongArch64-based boards.

LoongArch is a new RISC ISA developed by Loongson. It's a bit like
MIPS or RISC-V. LoongArch includes both 32-bit and 64-bit versions
(LoongArch32/LoongArch64).

Loongson 3A5000 and 3A6000 are the two existing CPUs of LoongArch64
and is used for PC products. It's BIOS supports ACPI and UEFI-only
boot. These CPUs supports SMP and SMT.

At present only LoongArch64 is supported by linux kernel.

Toolchain requirement:
binutils >= 2.40
gcc >= 13.1

For details, please check the following links:
https://lwn.net/Articles/861951/
https://loongson.github.io/LoongArch-Documentation/README-EN.html

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2024-05-04 14:14:16 +08:00
Daniel Golle
6bb2551343 Revert "mediatek: backport mt7622 dts fix for mt7531 switch id to 6.1"
This reverts commit 3fe239fcf8.
Now that we switched to Linux 6.6 this is no longer needed, and resulted
in a left-over file because it's removal was not included in the commit
removing all the other files intended for Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-04 00:15:57 +01:00
Zoltan HERPAI
3f7d8e20cd sunxi: add support for Lichee Pi Zero Dock (V3s) board
CPU:     Allwinner V3s single-core Cortex-A7 @ 1.2GHz
Memory:  64Mb DDR2 integrated into SoC package
Storage: 1x SDcard on board, 1x SDcard on dock
Network: 10/100M ethernet
Other:   4x buttons via LRADC, CSI

Flashing instructions:
  Standard sunxi SD card installation procedure - copy image to SD card,
  insert into SD card slot on the device and boot.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-04 00:41:02 +02:00
Mieczyslaw Nalewaj
263fde5ab8 ramips: remove unnecessary macros for previous kernel versions
Remove unnecessary 'if' macros for previous kernel versions.
After removing kernel 6.1 the kernel is always >= 6.6 so the conditions
are unnecessary.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[removed some more and also no longer include version.h]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-03 23:02:00 +01:00
Daniel Golle
2967e24d02 ramips: switch to Linux 6.6
Switch to Linux kernel version 6.6 and drop configs, files and patches
for Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-03 21:36:42 +01:00
Daniel Golle
2201d55257 mediatek: remove macros for previous kernel versions
Remove unnecessary 'if' macros for previous kernel versions.
After removing kernel 6.1 the kernel is always >= 6.6 so the conditions
are unnecessary.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-03 21:36:42 +01:00
Daniel Golle
6257ea018a mediatek: switch to Linux 6.6
Switch to Linux kernel version 6.6 and drop configs, files and patches
for Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-03 21:32:30 +01:00
Daniel Golle
fb2475e6bd generic: 6.6: fix and simplify blkdevparts= cmdline parsing
Import pending patch to fix the cmdline parsing of the "blkdevparts="
parameter which has been broken somewhen between Linux 6.1 and Linux 6.6.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-05-03 21:32:30 +01:00
Felix Fietkau
a5a941a997 kernel: add missing check for TCP GRO
Need to check if the skb data buffer is linear up to (and including) the TCP
header.

Fixes: https://github.com/openwrt/openwrt/issues/15359
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-03 18:45:46 +02:00
Felix Fietkau
2f5398588a kernel: backport upstream GRO fixes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-03 18:45:46 +02:00
Felix Fietkau
3fe239fcf8 mediatek: backport mt7622 dts fix for mt7531 switch id to 6.1
Fixes: ac8bfe316b ("generic: 6.1, 6.6: mt7530: import accepted patches")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-05-03 18:45:46 +02:00
Zoltan HERPAI
af87e5e9c1 sunxi: drop 6.1 support
Now that 6.6 is the default, remove the 6.1 config and the hack that
was required for the arm32 DTS dir change.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-03 14:53:45 +02:00
Zoltan HERPAI
e8c7b8a388 sunxi: switch default to 6.6
Switch the default kernel to 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-05-03 14:53:44 +02:00
Robert Marko
ecb3859cc9 ipq40xx: fritzrepeater-1200: fix MDIO and PHY probing
AVM FRITZ!Repeater 1200 does not use QCA807x PHY at all and thus it
disables all of the individual PHY nodes, however this is not enough
anymore since the conversion to PHY package.

Now its now enough to disable the PHY-s in the package alone, but the PHY
package node itself must also be disabled.

Fixes: 1b931c33a2 ("ipq40xx: adapt to new Upstream QCA807x PHY driver")
Fixes: #15355
Link: https://github.com/openwrt/openwrt/pull/15365
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-05-02 22:09:17 +02:00
Linus Walleij
219018185e bmips: Build U-Boot into the XG6846 target
It appears that the CFE boot loader found in the XG6846
cannot load kernels over a certain size, and the old
relocate hack is not working.

What to do? We can build a small U-Boot into the image,
make CFE boot that, place the kernel immediately after
U-Boot, and use U-Boot to boot the system instead.

The compiled u-boot.bin becomes around ~300KB and with
LZMA compression it will swiftly fit into 128KB, so
we use two 64KB erase blocks right after the CFE to
store an imagetag:ed U-Boot.

Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-01 21:32:23 +02:00
Linus Walleij
212da4dd48 bmips: Add Inteno XG6846 target
This adds a device tree and build options for the XG6846
switch/router to the BMIPS target.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: BMIPS4350 V7.5
 - RAM: 64 MB DDR
 - NOR Flash: 16 MB parallel (CFE and OS)
 - Ethernet LAN: 4x 1Gbit
 - Ethernet WAN: 2x 1Gbit, fiber and TP
 - Buttons: reset
 - LEDs: 7 or 8, power and USB LEDs are GPIO-based, the
   LAN LEDs are controlled by the Marvell DSA Switch.
 - USB: on some versions
 - UART: yes

The device ODM (original device manufacturer) is XAVi
http://www.xavi.com.tw/

It is possible to boot the initramfs version
openwrt-bmips-bcm6328-inteno_xg6846-initramfs.elf from
CFE by interrupting the boot on the UART console and downloading
it from a TFTP server e.g.:
CFE> r 192.168.1.2:openwrt-bmips-bcm6328-inteno_xg6846-initramfs.elf

Installation to target flash is not possible using CFE because
the image becomes too big for the CFE version found in these
devices. A separate U-Boot two-stage solution exists for
actually booting the device.

This device is called a "managed ethernet switch" by the vendor
and "media converter" or "fiber modem" by some of the ISPs
using it: the main purpose is to convert fiber connections to
ethernet, most devices just act as switches bridging the
fiber SFP to ethernet TP.

The device has a Marvell MV88E6352 DSA switch managed by
a BCM6328 BMIPS SoC.

This port makes it possible to use the XG6846 to grab an IP
number from the fiber connection and use all four LAN
connections out, turning it into a proper router.

This support is based mostly on the observations by the people on
the forum thread "Help with Inteno XG6846" where users NPeca75,
mrhaav, systemcrash and csom helped out to reverse engineer the
device. Then I made it work on the BMIPS target, figured out
the two-level switch hierarchy and settings.

Link: https://forum.openwrt.org/t/help-with-inteno-xg6846/68276/14
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-01 21:30:26 +02:00
Linus Walleij
79a483843c bmips: bcm6328: Compile in uImage splitter
Since we split the Inteno XG6846 "firmware" partition with the
uImage MTD splitter, we need to compile in support for this
splitting method into the BCM6328.

Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2024-05-01 21:30:16 +02:00
Elbert Mai
6a05d849e1 bcm27xx: correct cmdline.txt consoles for procd
Commit [ca8c30208d5e][1] updates procd to handle muliple "console=" on the
kernel command line. This affects Raspberry Pi builds because cmdline.txt
specifies a UART console and a virtual console on HDMI, in that order.

When procd finds multiple consoles on the command line, it attempts to
open /dev/console. Linux uses the [last console][2] for /dev/console, so
procd opens the virtual console on Raspberry Pi. This completely disables
the UART console and causes [strange behavior][3] on the virtual console.
Prior to ca8c30208d5e, procd would always open the first console, which is
the UART console.

The simplest fix without reverting ca8c30208d5e is to swap the order of
console options in cmdline.txt. By putting the UART console last, procd
handles the serial console correctly as before.

[1]: https://git.openwrt.org/?p=project/procd.git;a=commit;h=ca8c30208d5e1aaa2c0e3f732c4c9944735e9850
[2]: https://www.kernel.org/doc/html/latest/admin-guide/serial-console.html
[3]: https://forum.openwrt.org/t/rasberry-pi-4-model-b-keyboards-gone-wild/195594

Signed-off-by: Elbert Mai <code@elbertmai.com>
2024-05-01 20:22:42 +02:00
Arınç ÜNAL
3ea6125c50 ramips: mt7621-dts: describe switch PHYs and adjust PHY muxing
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.

This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.

Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus") on mainline Linux, we can describe the switch PHYs on
the MDIO bus of the switch on the device tree.

When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.

Describe the switch PHYs on mt7621.dtsi and remove defining the switch PHY
on the SoC's mdio bus node. When the PHY muxing is in use, the interrupts
for the muxed PHY won't work, therefore delete the "interrupts" property on
the devices where the PHY muxing feature is in use.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-05-01 13:50:54 +01:00
Arınç ÜNAL
6221316711 generic: 6.1, 6.6: mt7530: import pending PHY muxing detection patch
net: dsa: mt7530: detect PHY muxing when PHY is defined on switch MDIO bus

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-05-01 13:50:54 +01:00
Arınç ÜNAL
7c9cd43ea2 ramips: mt7621-dts: remove incorrect ethphy4 node for WAVLINK WL-WN573HX1
The ethernet-phy@4 node doesn't exist for WAVLINK WL-WN573HX1. Remove it
and the duplicate gmac0 node.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-05-01 13:50:54 +01:00
Arınç ÜNAL
007414aa70 ramips: mt7621-dts: do not modify ethernet node for MeiG SLT866
Currently, the pinctrl-0 property on the ethernet node is modified to
exclude the rgmii1 and rgmii2 pin groups to be claimed with rgmii1 and
rgmii2 functions, respectively. Remove the modification of this property as
we need these pin groups to be claimed with the said functions for this
device.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2024-05-01 13:50:54 +01:00
Nick Hainke
d06bcbe5bf zynq: 5.15: remove files
Remove files related to the old 5.15 kernel version as they are no
longer required.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-05-01 10:26:41 +02:00
Nick Hainke
ea72316426 zynq: set default kernel version to 6.1
Set default kernel version to 6.1, facilitating simpler testing across
a broader user base.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-05-01 10:24:49 +02:00
Shiji Yang
9e86e0b33b kernel: bump 6.1 to 6.1.89
Changelogs:
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.67
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.68
https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.1.69

Upstreamed patches:
target/linux/generic/backport-6.1/740-v6.9-01-netfilter-flowtable-validate-pppoe-header.patch [1]
target/linux/generic/backport-6.1/740-v6.9-02-netfilter-flowtable-incorrect-pppoe-tuple.patch [2]
target/linux/generic/backport-6.1/790-48-STABLE-net-dsa-mt7530-trap-link-local-frames-regardless-of-.patch [3]
target/linux/generic/backport-6.1/790-50-v6.10-net-dsa-mt7530-fix-mirroring-frames-received-on-loca.patch [4]
target/linux/generic/backport-6.1/790-16-v6.4-net-dsa-mt7530-set-all-CPU-ports-in-MT7531_CPU_PMAP.patch [5]
target/linux/generic/backport-6.1/790-46-v6.9-net-dsa-mt7530-fix-improper-frames-on-all-25MHz-and-.patch [6]
target/linux/generic/backport-6.1/790-47-v6.10-net-dsa-mt7530-fix-enabling-EEE-on-MT7531-switch-on-.patch [7]
target/linux/mediatek/patches-6.1/220-v6.3-clk-mediatek-clk-gate-Propagate-struct-device-with-m.patch [8]
target/linux/mediatek/patches-6.1/222-v6.3-clk-mediatek-clk-mtk-Propagate-struct-device-for-com.patch [9]
target/linux/mediatek/patches-6.1/223-v6.3-clk-mediatek-clk-mux-Propagate-struct-device-for-mtk.patch [10]
target/linux/mediatek/patches-6.1/226-v6.3-clk-mediatek-clk-mtk-Extend-mtk_clk_simple_probe.patch [11]

Symbol changes:
MITIGATION_SPECTRE_BHI (new) [12]
SPECTRE_BHI_{ON,OFF} (deprecated) [12]

References:
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=8bf7c76a2a207ca2b4cfda0a279192adf27678d7
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=f1c3c61701a0b12f4906152c1626a5de580ea3d2
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=19643bf8c9b5bb5eea5163bf2f6a3eee6fb5b99b
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=e86c9db58eba290e858e2bb80efcde9e3973a5ef
[5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=013c787d231188a6408e2991150d3c9bf9a2aa0b
[6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=41a004ffba9b1fd8a5a7128ebd0dfa3ed39c3316
[7] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=7d51db455ca03e5270cc585a75a674abd063fa6c
[8] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=082b831488a41257b7ac7ffa1d80a0b60d98394d
[9] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=6f5f72a684a2823f21efbfd20c7e4b528c44a781
[10] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=a4fe8813a7868ba5867e42e60de7a2b8baac30ff
[11] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=c1d87d56af063c87961511ee25f6b07a5676d27d
[12] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.1.89&id=d844df110084ef8bd950a52194865f3f63b561ca
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-04-30 20:18:15 +02:00
Shiji Yang
dcdcb9228b generic: MIPS64: fix detect_memory_region() compilation error
1. Enable this feature only for 32-bit CPUs as MIPS64 can not
   access the full range unmapped uncached memory.

2. Backport this fix to the 6.1 old LTS kernel.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-04-30 19:34:02 +02:00
Isaev Ruslan
be37ab6e51 qualcommax: ipq807x: uboot-envtools: yuncore ax880
There was no config in the uboot-envtools package, so there is no
generated /etc/fw_env.config for the fw_printenv and fw_setenv utils.
Since uboot-envtools 2024.01, there is a way to make these utils work
without /etc/fw_env.config if the DT has an env partition with the prop.:

compatible = "u-boot,env";

So, this commit adds the prop. above to the appsblenv:0 partition
in the yuncore ax880 DTS file.

Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15305
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-30 13:51:15 +02:00
Ryan Salsbury
47da1786e9 ipq40xx: fix I2C pin config on Aruba AP-303H
Turn on SoC pull-ups on I2C pins, since there are no discrete pull-up
resistors on the bus.

Increase clock to 400 kHz. Both chips on the bus support 400 kHz. I
tested the ISL28022 at 4,000 reads/sec and didn't see any garbled output
or bus hangs, even with SoC drive strength reduced to 2 for the test.

Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15334
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-30 12:01:04 +02:00
Zoltan HERPAI
0f5da3977e sifiveu: drop 6.1 support
Now that 6.6 is the default, remove the 6.1 config and patches.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-30 11:02:48 +02:00
Zoltan HERPAI
81fafec29d sifiveu: switch default to 6.6
Switch the default kernel to 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-30 11:02:47 +02:00
Tianling Shen
790082098e
mediatek: switch to fitblk for JDCloud RE-CP-03
Use the new fitblk driver.

Tested-By: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-04-30 03:28:13 +01:00
Christian Marangi
284735246c
qualcommax: ipq60xx: mute warning on bootcount enable compile
ipq60xx bootcount script include /lib/functions that produce warning
when the script is enabled on image compilation. This script is already
included by /etc/rc.common hence it's not needed.

While at it also fix the format of the switch case.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-29 21:54:39 +02:00
Felix Fietkau
ed29c31972 mediatek: fix remaining invalid MT7531 switch reg IDs
See commit 8b66f1a06d:
"mediatek: correct address of MT753x switch IC"

Fixes: ac8bfe316b ("generic: 6.1, 6.6: mt7530: import accepted patches")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-29 12:00:09 +02:00
Mieczyslaw Nalewaj
7d5f7b8b6c generic: 6.6: add kernel missing symbol CONFIG_SPI_BCMBCA_HSSPI
Add missing symbol CONFIG_SPI_BCMBCA_HSSPI causing bcm4908 compilation errors.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15320
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-29 10:20:56 +02:00
David Bauer
eec18118d0 mpc85xx: convert WS-AP3710i to simpleImage wrapper
Convert the Enterasys WS-AP3710i access point to use the simpleImage
wrapper.

This is necessary, as the bootlaoder does not align the DTB correctly
(and does not support altering the FDT loadaddress). Booting images with
kernels 5.15 and later can break depending on the alignment on the DTB
within the FIT image.

Signed-off-by: David Bauer <mail@david-bauer.net>
2024-04-29 03:18:54 +02:00
Hauke Mehrtens
a638d013b1 malta: refresh kernel 6.6 configuration
This refreshes the configuration on top of kernel 6.6 and activates it
as test kernel configuration.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2024-04-29 00:24:02 +02:00
Tony Ambardar
a18920edcc kernel/malta: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2024-04-29 00:24:02 +02:00
Tony Ambardar
3d0bf9091f kernel/malta: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2024-04-29 00:24:02 +02:00
Daniel Golle
5709254690 mediatek: bpi-r4: store random MAC addresses for the BPi-R4
Despite coming with multiple I2C EEPROMs supposedly dedicated for that
purpose, the BPi-R4 does not seem to have factory assigned MAC addresses.
Hence, just like for all other BPi boards, store a randomly generated
MAC address on first boot and derive WAN and Wi-Fi MAC addresses from
that as well. Not perfect, but better than random on every boot.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-28 21:46:51 +01:00
Daniel Golle
abbcbb9228 mediatek: bpi-r3-mini: persist WiFi and WAN MAC addresses
Derive WAN and WiFi MAC addresses from the (random) MAC address stored
in the U-Boot environment.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-28 21:46:51 +01:00
John Audia
dceb5938f8 kernel: bump 6.6 to 6.6.29
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.29

Removed upstreamed:
	generic/backport-6.6/740-v6.9-01-netfilter-flowtable-validate-pppoe-header.patch[1]
	generic/backport-6.6/740-v6.9-02-netfilter-flowtable-incorrect-pppoe-tuple.patch[2]
	generic/backport-6.6/790-29-v6.9-net-dsa-mt7530-fix-improper-frames-on-all-25MHz-and-.patch[3]
	generic/backport-6.6/790-31-v6.10-net-dsa-mt7530-fix-enabling-EEE-on-MT7531-switch-on-.patch[4]
	generic/backport-6.6/790-34-v6.10-net-dsa-mt7530-fix-mirroring-frames-received-on-loca.patch[5]
	generic/backport-6.6/790-35-v6.10-net-dsa-mt7530-fix-port-mirroring-for-MT7988-SoC-swi.patch[6]
	mediatek/patches-6.6/963-net-ethernet-mtk_eth_soc-fix-WED-wifi-reset.patch[7]

Manually rebased:
	generic/backport-6.6/790-23-v6.9-net-dsa-mt7530-get-rid-of-priv-info-cpu_port_config.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=a2471d271042ea18e8a6babc132a8716bb2f08b9
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=4ed82dd368ad883dc4284292937b882f044e625d
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=21b9d89d93422221cdda1b82fd075fa3c94a11d9
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=bd41ee1efd478852a0882ce5f136bc2b5e83eff2
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=d1be3960539249a8690ed09a29d0e3bf34189dd2
6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=f8de1b6208bf71bd3102548d33dd8475573ad2ea
7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.29&id=6855f724f19620c3ddff57c349e0abba797475b1

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2024-04-28 21:51:03 +02:00
Nick Hainke
de976f8fe0 at91: 5.15: remove old config and patch files
6.1 is now default so remove old config and patch files.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-04-28 17:50:37 +02:00
Nick Hainke
4088ea0475 at91: set 6.1 as default kernel version
Adjust the kernel version to default 6.1 in order to facilitate testing
for a broader audience.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-04-28 17:50:37 +02:00
Nick Hainke
436aa110c6 zynq: 6.1: set testing kernel
Allow selecting 6.1 as testing kernel on zynq.

Tested-by: Luis Araneda <luaraneda@gmail.com> # Zybo Z7-20
Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-04-28 17:45:41 +02:00
Nick Hainke
0227127e79 zynq: 6.1: refresh kernel config
Refresh the kernel config by runnnig make kernel_menuconfig.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-04-28 17:45:41 +02:00
Nick Hainke
4fdb5e8dcf kernel/zynq: Restore kernel files for v5.15
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.

See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-04-28 17:45:41 +02:00
Nick Hainke
f41bee1788 kernel/zynq: Create kernel files for v6.1 (from v5.15)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2024-04-28 17:45:41 +02:00
Robert Marko
2aa6c875f8 ipq40xx: refresh patches again
CI tells us that we need to, so lets refresh them.

Fixes: 4265fe9348 ("ipq40xx: refresh patches")

Link: https://github.com/openwrt/openwrt/pull/15310
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-28 11:09:20 +02:00
Robert Marko
4265fe9348 ipq40xx: refresh patches
CI tells us that we need to, so lets refresh them.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-04-27 23:29:14 +02:00
Felix Fietkau
7116d2f2b0 kernel: update fraglist GRO patch to the latest upstream submission
Cosmetic fixes + IPv6 NAT support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-27 20:39:07 +02:00
Felix Fietkau
45a8e962a5 kernel: fix crash with multicast-to-unicast and fraglist GRO
Avoid calls to skb_copy, which creates invalid packets that cause a crash
on segmentation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-27 20:33:36 +02:00
Daniel Golle
fe9d2ccbc3 generic: v6.1, v6.6: add patch to fix PHY-muxing on MT7530
Move accepted patches to backport folder, re-add previously removed patch
which caused havoc on MT7621 and add the (still pending) fix.

Fixes: d40691a5fb ("generic: 6.1, 6.6: mt7530: import pending patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-27 16:14:10 +01:00
Antonio Flores
db89030cb2 kernel: generic backport 6.1: rename mistyped .patch file
Rename mistyped file .patc to patch

Fixes: ac8bfe316b ("generic: 6.1, 6.6: mt7530: import accepted patches")
Signed-off-by: Antonio Flores <antflores627@gmail.com>
2024-04-27 16:14:09 +01:00
Mieczyslaw Nalewaj
f3895fd30a bcm4908: set kernel 6.6 as a testing version
Add kernel 6.6 for testing.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-27 12:14:00 +02:00
Mieczyslaw Nalewaj
9d8e73656c bcm4908: remove 5.15 support
Now that 6.1 is default, remove 5.15 support.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
2024-04-27 12:14:00 +02:00
Ulrich Stark
7cb161ae84 qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
For this particualar device we get random MAC's for Wifi on each (re-)boot.
This is because art partition/pre caldata do not contain valid MAC addresses.

As we have now a new/better approach with ath11k_patch_mac we can use it for
this device too.

I'm using this approach for like two weeks and its working flawlessly.

Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>

qualcommax: IPQ807x: ZyXEL NBG7815: Fix random Wifi MAC
Changing order to 3/phy0/5G-1, 2/phy1/2G, 4/phy2/5G-2.

Signed-off-by: Ulrich Stark <pwned-pixel@posteo.de>
2024-04-27 12:01:07 +02:00
Ryan Salsbury
026fbd650a ipq40xx: fix USB on Aruba AP-303H
Enable USB 3.0 controller, disable USB 2.0 controller.

The USB 2.0 port on the AP-303H is actually connected to the USB 3.0
controller's HS phy. Enable the HS phy only, since the SS lanes are not
brought out to the connector.

Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
2024-04-27 11:27:32 +02:00
Ryan Salsbury
4c5cb58805
ipq40xx: use nvmem ethernet MACs on Aruba AP-303H
Use NVMEM to assign "factory sticker" MAC address to WAN ethernet
interface. Set LAN address to sticker + 1.

Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
2024-04-27 11:23:29 +02:00
Daniel Golle
a8dde7e5bd generic: 6.1, 6.6: remove patch which breaks WAN on MT7621
Importing pending patch "net: dsa: mt7530: move MT753X_MTRAP operations
for MT7530" broke WAN connectivity on most MT7621 which use PHY-muxing
to hook up either port 0 or port 4 to GMAC1.

Remove it for now until the author submits a fixed version.

Fixes: https://github.com/openwrt/openwrt/issues/15279
Fixes: https://github.com/openwrt/openwrt/issues/15273
Fixes: d40691a5fb ("generic: 6.1, 6.6: mt7530: import pending patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-27 03:19:03 +01:00
Stijn Tintel
2c0cec1eb0 kernel: move mv88e6xxx fix to generic backports
The backports introduced in commit d40756563c ("kernel: backport
phylink changes from mainline Linux") broke the mv88e6xxx DSA driver.
A backport to fix this was added to the kirkwood target, but as it is
used in multiple targets, and there's a kmod package for it, the fix
should be in generic backports.

This fixes the switch on the WatchGuard Firebox M300 when running the
6.1 testing kernel.

There is no need to backport the fix for the 6.6 kernel, as it was
included in 6.6.5.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2024-04-26 19:56:19 +03:00
Christian Marangi
0bb8d68de5
ipq40xx: set DEVICE_DTS_DIR to /qcom by default
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-26 12:52:31 +02:00
Christian Marangi
b0dae2098a
ipq806x: set DEVICE_DTS_DIR to /qcom by default
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-26 12:52:31 +02:00
Felix Fietkau
61c846ea7c bcm53xx: update 600-net-disable-GRO-by-default.patch after recent GRO change
Fixes build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-26 12:42:43 +02:00
Christian Marangi
2d5509f529
ipq40xx: drop 6.1 support
Drop support for ipq40xx for kernel 6.1.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-26 12:30:42 +02:00
Christian Marangi
414646ef6c
ipq40xx: switch default to 6.6
Switch default kernel version for ipq40xx to 6.6.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-26 12:30:01 +02:00
Christian Marangi
a04b7cbc40
ipq806x: drop 6.1 support
Drop support for ipq806x for kernel 6.1.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-26 12:27:21 +02:00
Christian Marangi
fd36d4a7ab
ipq806x: switch default to 6.6
Switch default kernel version for ipq806x to 6.6.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-04-26 12:26:53 +02:00
Felix Fietkau
366544083e ath79: update 900-unaligned_access_hacks.patch after recent GRO change
Fixes build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-26 12:24:46 +02:00
Zoltan HERPAI
4e9f0e5be4 sunxi: update the 6.6 DTS_DIR hack
Update and simplify the 6.1 vs. 6.6 DTS_DIR hack until 6.1 support is gone.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-26 11:07:43 +02:00
Felix Fietkau
b5c53848c3 kernel: improve GRO performance
For packets not belonging to a local socket, use fraglist GRO instead of
regular GRO. This make segmenting packets very cheap and avoids the need for
selectively disabling GRO

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-26 06:31:27 +02:00
Felix Fietkau
98834a4c3f kernel: backport flow offload pppoe fix
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-04-26 06:31:27 +02:00
Zoltan HERPAI
ee4e69cc35 sunxi: 6.6: set testing kernel
Allow selecting 6.6 as testing kernel on sunxi.

Runtime-tested:
 - Linksprite pcDuino (cortexa8)
 - Olimex A20 Micro (cortexa7)
 - Pine64 SoM (cortexa53)

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 16:34:25 +02:00
Zoltan HERPAI
7de163d58b sunxi: 6.6: refresh patches
Refresh kernel patches.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 16:34:25 +02:00
Zoltan HERPAI
82df12e98a sunxi: update image Makefile to reflect updated DTS structure in 6.6
For the ARM arch on 6.6, DTS files are moved into their vendor directories,
mimicking arm64. Reflect this in the image Makefile.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 16:34:25 +02:00
Zoltan HERPAI
9122474226 sunxi: 6.6: refresh kernel configs
Refresh kernel config.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 16:34:25 +02:00
Zoltan HERPAI
438dc54936 sunxi: 6.6: remove upstreamed patches
Remove patches that have been upstreamed.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 16:34:25 +02:00
Zoltan HERPAI
9e348da477 kernel/sunxi: Restore kernel files for v6.1
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.

See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 16:34:25 +02:00
Zoltan HERPAI
3c69b9a818 kernel/sunxi: Create kernel files for v6.6 (from v6.1)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 16:34:25 +02:00
Zoltan HERPAI
2d838f3f93 mxs: drop 6.1 support
Now that 6.6 is the default, remove the 6.1 config and the hack that
was required for the arm32 DTS dir change.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 14:33:22 +02:00
Zoltan HERPAI
dbe9084adb mxs: switch default to 6.6
Switch the default kernel to 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2024-04-25 14:31:59 +02:00
Martin Kennedy
84a48ce400 mpc85xx: fix address config for ws-ap3825i
In commit 6a8b831593 ("mpc85xx: p1010: change wrapper address of
simple image devices"), we adjusted the wrapper address in the recipe
code for all mpc85xx simpleimage devices, including the Extreme
Networks WS-AP3825i. However, we did not also adjust the
KERNEL_LOADADDR and KERNEL_ENTRY config values for this board. This
broke the simpleimage wrapper loader, causing GitHub issue #15237.

Adjust those config values so we go back to pointing at the right
address. We don't exactly need the memory, but it's also not exactly a
punishment in this case.

Run-tested on a ws-ap3825i.

Fixes: commit 6a8b831593 ("mpc85xx: p1010: change wrapper address of
simple image devices")

Tested-by: Martin Kennedy <hurricos@gmail.com>

Signed-off-by: Martin Kennedy <hurricos@gmail.com>
2024-04-25 03:00:17 +03:00
Daniel Golle
9599a85dc2 mediatek: sync cpufreq support with changed compatible string
The compatible string for the MediaTek MT7988 SoC ended up being
'mediatek,mt7988a' instead of 'mediatek,mt7988' in the now upstream
dtsi. Adapt the cpufreq driver so support for frequency scaling is
again usable.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-04-24 21:05:46 +01:00