Add environment settings for the BananaPi BPI-R4 router board which
can boot from (and store its bootloader environment on) micro SD card,
SPI-NAND and eMMC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use function instead of duplicating the env settings on UBI for
OpenWrt-built U-Boot over and over.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point.
Oem firmware is a custom openwrt 21.02 snapshot version.
We can gain access via ssh once we remove the root password.
Hardware specification:
SoC: MediaTek MT7981A 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN)
1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN)
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976D
LEDS: 1x (Red, Blue and Green)
Button: Reset
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC GND TX RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface (http://apipaddress/computer/login.html),
and download the
configuration(http://apipaddress/computer/config.html).
2. Rename downloaded backup config - 'backup.file to backup.tar.gz',
Enter 'fakeroot' command then decompress the configuration:
tar -zxf backup.tar.gz
3. Edit 'etc/shadow', update (remove) root password:
With password =
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::'
to
Without password =
'root::0:99999:7:::'
'root::0:99999:7:::'
4. Repack 'etc' directory back to a new backup file:
tar -zcf backup-ssh.tar.gz etc/
5. Rename new config tar.gz file to 'backup-ssh.file'
Exit fakeroot - 'exit'
6. Upload new configuration via web interface, now you
can SSH with the following:
'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'.
Backup the mtd partitions
- https://openwrt.org/docs/guide-user/installation/generic.backup
7. Copy openwrt factory firmware to the tmp folder to install via ssh:
'scp -o HostKeyAlgorithms=+ssh-rsa \
-o PubkeyAcceptedAlgorithms=+ssh-rsa \
*-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \
root@192.168.10.1:/tmp/'
'sysupgrade -n -F \
/tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin'
8. Once led has stopped flashing - Connect via ssh with the
default openwrt ip address - 'ssh root@192.168.1.1'
9. SSH copy the openwrt sysupgrade firmware and upgrade
as per the default instructions.
Signed-off-by: David Bentham <db260179@gmail.com>
This reverts commit dcdcfc1511.
This is a firmware for third-party u-boot mod, which should not
be carried here by us.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Linksys MX4200 is a 802.11ax Tri-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 512Mb NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* RGB system led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel
Replace (X) with your model version either 1 or 2
Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
R32 is like the M32 part of the EAGLE PRO AI series from D-Link.
Specification:
- MT7622BV SoC with 2.4GHz wifi
- MT7975AN + MT7915AN for 5GHz
- MT7531BE Switch
- 512MB RAM
- 128 MB flash
- 2 LEDs (Status and Internet, both can be either orange or white)
- 2 buttons (WPS and Reset)
Compared to M32, the R32 has the following differences:
- 4 LAN ports instead of 2
- The recory image starts with DLK6E6015001 instaed of DLK6E6010001
- Individual LEDs for power and internet
- MAC address is stored at another offset in the ODM partition
MAC addresses:
- WAN MAC is stored in partition "Odm" at offset 0x81
- LAN (as printed on the device) is WAN MAC + 1
- WLAN MAC (2.4 GHz) is WAN MAC + 2
- WLAN MAC (5GHz) is WAN MAC + 3
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Download openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-recovery.bin
Flashing via uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-initramfs-kernel.bin.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "1. System Load Linux to SDRAM via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Create a backup of the Kernel1 partition, this file is required if a revert to stock should be done later
- Perform a sysupgrade using openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Revert back to stock using the Recovery Web Interface:
- Set your IP address to 192.168.0.10, subnetmask 255.255.255.0
- Press the reset button while powering on the deivce
- Keep the reset button pressed until the internet LED blinks fast
- Open a Chromium based and goto http://192.168.0.1
- Flash a decrypted firmware image from D-Link. Decrypting an firmware image is described below.
Decrypting a D-Link firmware image:
- Download https://github.com/RolandoMagico/firmware-utils/blob/M32/src/m32-firmware-util.c
- Compile a binary from the downloaded file, e.g. gcc m32-firmware-util.c -lcrypto -o m32-firmware-util
- Run ./m32-firmware-util R32 --DecryptFactoryImage <OriginalFirmware> <OutputFile>
- Example for firmware R32A1_FW103B01: ./m32-firmware-util R32 --DecryptFactoryImage R32A1_FW103B01.bin R32A1_FW103B01.decrypted.bin
Revert back to stock using uBoot:
- Open the case, connect to the UART console
- Set your IP address to 10.10.10.3, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides the previously created backup of the Kernel1 partition.
- You can rename the file to iverson_uImage (no extension), then you don't have to enter the whole file name in uboot later.
- Power on the device and select "2. System Load Linux Kernel then write to Flash via TFTP." in the boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to FLASH will start. After a few seconds the stock firmware should start again
There is also an image openwrt-mediatek-mt7622-dlink_eagle-pro-ai-r32-a1-squashfs-tftp.bin which can directly be flashed via U-Boot and TFTP.
It can be used if no backup of the Kernel1 partition is reuqired.
Flahsing via OEM web interface is currently not possible, the OEM images are encrypted. Creating images is only possible manually at the moment.
The support for the M32/R32 already includes support for flashing from the OEM web interface:
- The device tree contains both partitions (Kernel1 and Kernel2) with conditions to select the correct one based on the kernel command line
- The U-Boot variable "boot_part" is set accordingly during startup to finish the partition swap after flashing from the OEM web interface
- OpenWrt sysupgrade flashing always uses the partition where it was initially flashed to (no partition swap)
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
(based on support for ASUS RT-AX59U by liushiyou006)
SOC: MediaTek MT7986
RAM: 512MB DDR4
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Upgrade from AsusWRT to OpenWRT using UART
Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24. Rename the image to rtax59u.bin.
Connect the PC with TFTP server to the RT-AX59U.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console, interrupt the autoboot process by pressing '4' when prompted.
Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax59u.bin
$ bootm 0x46000000
Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Upgrade from AsusWRT to OpenWRT using WebUI
Download transit TRX file from https://drive.google.com/drive/folders/1A20QdjK7Udagu31FSszpWAk8-cGlCwsq
Upgrade firmware from WebUI (192.168.50.1) using downloaded TRX file
Wait for OpenWRT to boot (192.168.1.1).
Upgrade system with sysupgrade image using luci or uploading it through scp and executing sysupgrade command
MAC Address for WLAN 5g is not following the same algorithm as in AsusWRT.
We have increased by one the WLAN 5g to avoid collisions with other networks from WLAN 2g
when bit 28 is already set.
: Stock : OpenWrt
WLAN 2g (1) : C8:xx:xx:0D:xx:D4 : C8:xx:xx:0D:xx:D4
WLAN 2g (2) : : CA:xx:xx:0D:xx:D4
WLAN 2g (3) : : CE:xx:xx:0D:xx:D4
WLAN 5g (1) : CA:xx:xx:1D:xx:D4 : CA:xx:xx:1D:xx:D5
WLAN 5g (2) : : CE:xx:xx:1D:xx:D5
WLAN 5g (3) : : C2:xx:xx:1D:xx:D5
WLAN 2g (1) : 08:xx:xx:76:xx:BE : 08:xx:xx:76:xx:BE
WLAN 2g (2) : : 0A:xx:xx:76:xx:BE
WLAN 2g (3) : : 0E:xx:xx:76:xx:BE
WLAN 5g (1) : 0A:xx:xx:76:xx:BE : 0A:xx:xx:76:xx:BF
WLAN 5g (2) : : 0E:xx:xx:76:xx:BF
WLAN 5g (3) : : 02:xx:xx:76:xx:BF
Signed-off-by: Xavier Franquet <xavier@franquet.es>
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon@gmail.com>
Rostelecom RT-FE-1A is a wireless WiFi 5 router manufactured by Sercomm
company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: No
Button: 2 buttons (Reset & WPS)
LEDs:
- 1x Power (green, unmanaged)
- 1x Status (green, gpio)
- 1x 2.4G (green, hardware, mt76-phy0)
- 1x 2.4G (blue, gpio)
- 1x 5G (green, hardware, mt76-phy1)
- 1x 5G (blue, gpio)
- 5x Ethernet (green, hardware, 4x LAN & WAN)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot
Installation
-----------------
1. Login to the router web interface (default http://192.168.0.1/)
under "admin" account
2. Navigate to Settings -> Configuration -> Save to Computer
3. Decode the configuration. For example, using cfgtool.py tool (see
related section):
cfgtool.py -u configurationBackup.cfg
4. Open configurationBackup.xml and find the following block:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="<some value>" writable="1" encryption="1" password="1" />
</OBJECT>
5. Replace <some value> by a new superadmin password and add a line
which enabling superadmin login after. For example, the block after
the changes:
<OBJECT name="User." type="object" writable="1" encryption="0" >
<OBJECT name="1." type="object" writable="1" encryption="0" >
<PARAMETER name="Password" type="string" value="s0meP@ss" writable="1" encryption="1" password="1" />
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
</OBJECT>
6. Encode the configuration. For example, using cfgtool.py tool:
cfgtool.py -p configurationBackup.xml
7. Upload the changed configuration (configurationBackup_changed.cfg) to
the router
8. Login to the router web interface (superadmin:xxxxxxxxxx, where
xxxxxxxxxx is a new password from the p.5)
9. Enable SSH access to the router (Settings -> Access control -> SSH)
10. Connect to the router using SSH shell using superadmin account
11. Run in SSH shell:
sh
12. Make a mtd backup (optional, see related section)
13. Change bootflag to Sercomm1 and reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot
14. Login to the router web interface under admin account
15. Remove dots from the OpenWrt factory image filename
16. Update firmware via web using OpenWrt factory image
Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.0.2
MAC Addresses
-------------
+-----+------------+---------+
| use | address | example |
+-----+------------+---------+
| LAN | label | f4:*:66 |
| WAN | label + 11 | f4:*:71 |
| 2g | label + 2 | f4:*:68 |
| 5g | label + 3 | f4:*:69 |
+-----+------------+---------+
The label MAC address was found in Factory, 0x21000
cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The previous offsets did also work, as they've wrapped back to 0x0.
However, in reality the environment starts at offset 0x0 of the
u-boot-env MMC partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SoC: MediaTek MT7981BA
RAM: 1GB DDR4 (NANYA NT5AD512M16C4-JR)
MMC: 8GB eMMC (Samsung 8GTF4R)
ETH: 1000Base-T LAN (ePHY)
2500Base-T WAN (MaxLinear GPY211C)
BTN: 1x Reset Button
LED: System (blue/white)
VPN (white)
USB: 1x USB-A (USB 3.0)
UART: 115200 8N1 - Pinout on board next to LAN port
Don't connect 3.3V!
Known Issues
------------
U-Boot vendor recovery does not seem to accept any images, neither
GL.iNet images nor OpenWrt images. Recovery requires serial access!
Installation
------------
Upload the OpenWrt sysupgrade image to the Gl.iNet Web-UI. Make sure to
not retain existing settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender,
manufactured by Alpha Networks [8WAPAC28.1A1G].
(in square brackets: PCB silkscreen markings)
Specifications:
* CPU (Qualcomm Atheros QCA9563-AL3A [U5]):
775 MHz single core MIPS 74Kc;
* RAM (Winbond W9751G6KB-25J [U3]):
64 MiB DDR2;
* ROM (Winbond W25Q128FV [U16]):
16 MiB SPI NOR flash;
* Ethernet (AR8033-AL1A PHY [U1], no switch):
1 GbE RJ45 port (no PHY LEDs);
* Wi-Fi
* 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]):
3x3 802.11n;
* 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]):
3x3 802.11ac Wave 1;
* 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3];
* GPIO LEDs:
* RSSI low (red/green) [D2];
* RSSI medium (green) [D3];
* RSSI high (green) [D4];
* status (red/green) [D5];
* GPIO buttons:
* WPS [SW1], co-located with status LED;
* reset [SW4], accessible via hole in the side;
* Serial/UART:
Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch;
125000-8-n-1 in U-boot, 115200-8-n-1 in kernel;
* Misc:
* 12V VCC [JP2], fed from internal 12V/1A AC to DC converter;
* on/off slide switch [SW2] (disconnects VCC mechanically);
* unpopulated footprints for a Wi-Fi LED [D1];
* unpopulated footprints for a 4-pin 3-position slide switch (SW3);
MAC addresses:
* Label = LAN;
* 2.4 GHz WiFi = LAN;
* 5 GHz WiFi = LAN+2;
Installation:
* `factory.bin` can be used to install OpenWrt from OEM firmware via the
standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html
* `recovery.bin` can be used to install OpenWrt (or revert to OEM
firmware) from D-Link Web Recovery. To enter web recovery, keep reset
button pressed and then power on the device. Reset button can be
released when the red status LED is bright; it will then blink slowly.
Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and
upload 'recovery.bin'. Note that in web recovery mode the device
ignores ping and DHCP requests.
Note: 802.11s is not supported by the default `ath10k` driver and
firmware, but is supported by the non-CT driver and firmware variants.
The `-smallbuffers` driver variant is recommended due to RAM size.
Co-developed-by: Anthony Sepa <protectivedad@gmail.com>
Signed-off-by: Rani Hod <rani.hod@gmail.com>
The ubootmod bootlaoder for EX5601-T0 uses two partitions
in ubi to store enviroment variables. so proper config
is needed.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Based on patch adding support for similar Zbtlink ZBT-Z8103AX device by
Ian Ishmael C. Oderon.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
SoC: QCA9531(650MHz)
RAM: DDR2 128M
Flash: SPI NOR 16M + SPI NAND 128M
WiFi: 2.4GHz with 2 antennas(WiFi/Thread)
Ethernet:
1xLAN(10/100M)
2xWAN(10/100M)
Button: 1x Reset Button
Switch: 1x Mode switch
LED: 1x Blue LED + 1x White LED + 1x Orange LED
IOT: Thread + ZigBee/Zwave
By uboot web failsafe:
Push the reset button for 5 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
GND RXD TXD, beginning from the external antennas. 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet
Wlan:
* 4x4 in 2.4GHz : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)
Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A
Mounting: Wall and ceiling
```
```
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to the console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Extreme Networks AP3935i/e -
https://www.extremenetworks.com/support/documentation/access-points-ap3935i-e/
SoC: IPQ8068 QYY AT46279K45060I
RAM: NANYA 1527 NT5CC256M16DP-DI 515073W0EF 7 TW
FLASH: NOR - S25FL256S1 - 32MB
NAND - Macronix MX30UF4G28AB - 512MB
LAN: Atheros AR8035-A J5150WL 1515 CN - RGMII
LAN2: Atheros AR8033-AL1A SKCSR.AJ1 1444 China - SGMII
WLAN2: QCA9990 OVV FNPV209 K451406
WLAN5: QCA9990 OVV FNPV209 K451406
SERIAL: RS232 Port (115200 8n1) Cisco console cable and
4pin Serial Header | 3.3 | GND | RX | TX
MAC address for LAN1/LAN2/WLAN 2G/WLAN 5G in uboot env
* Installation via either RJ45 console or on-board 4 PIN header
Install Method
--------------
1) Setup TFTP server, and place
openwrt-ipq806x-generic-extreme_ap3935-initramfs-uImage image
in /srv/tftp or similar
2) Connect to console on router and connect ethernet port "LAN1" to
your LAN
3) Interupt the boot with any character
4) Login with admin/new2day for default password
(use reset/FactoryDefault if password needs to be reset)
5) Set serverip to TFTP IP: set serverip 192.168.1.2
6) Set ipaddr to another IP: set ipaddr 192.168.1.101
7) Make uboot ping something to activate eth0 on boot:
set bootcmd 'ping 192.168.1.1; run boot_flash'
saveenv
8) TFTP image to RAM:
tftpboot 0x42000000
openwrt-ipq806x-generic-extreme_ap3935i-initramfs-uImage
9) Boot image: bootm 0x42000000
In OpenWRT, "LAN1" is LAN, "LAN2" is WAN
10) SFTP openwrt-ipq806x-generic-extreme_ap3935-squashfs-nand-sysupgrade.bin
image to /tmp
11) sysupgrade /tmp/openwrt-*-nand-sysupgrade.bin
Signed-off-by: Glen Lee <g2lee@yahoo.com>
```
Specifications:
* CPU: Qualcomm IPQ8072A, SoC Version: 2.0, Quad core Cortex-A53 1.6896 GHz
* RAM: 1 GiB of DDR4 600 MHz
* Flash: NAND 2x256 MiB (Macronix MX30UF2G18AC)
* 4 RGB LEDs: Power, LAN, 2.4GHz and 5GHz
* UART: Two 4-pin unpopulated headers under the LEDs.
Use the header closest to LED 4 and 5.
They are marked with a white stroke.
TX RX GND, beginning from "4". 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet (QCA8081)
Wlan:
* 4x4 in 2.4GHz: 802.11b/g/n/ax
* 4x4 in 5.0GHz: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 3.1/4.3 dBi (2.4GHz/5GHz)
Power:
* PoE+ 802.3at/af 25.5W
* DC 12V 2.5A
```
```
Note: The OpenWrt image is setup with DHCP and not a static IP.
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax620-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax620-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: ESMT F50L1G41LB 128MB
- RAM: Nanya NT5CC128M16JR-EK 256MB
- Ethernet: 4 x 10/100/1000 Mbps
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: Reset, Mesh
- Power: DC 12V 1A
- UART: 3.3v, 115200n8
| Layout: |
| :-------- |
| <Antenna> |
| VCC |
| GND |
| Tx |
| Rx |
**Flash instructions:**
1. Rename `openwrt-mediatek-filogic-cetron_ct3003-squashfs-factory.bin` to `factory.bin`.
2. Upload the `factory.bin` using the device's Web interface.
3. Click the upgrade button and wait for the process to finish.
4. Access the OpenWrt interface using the same password.
5. Use the 'Restore' function to reset the firmware to its initial state.
**Notes:**
If you plan to recovery the stock firmware in the future, it's advisable
to connect the device via the serial port and enter failsafe mode to
back up all the MTD partitions before proceeding the steps above.
Signed-off-by: Patricia Lee <patricialee320@gmail.com>
Recent envtools update to 2023.07.02 has introduced a breakage when trying
to parallel build with the following error:
/bin/sh: line 1: scripts/basic/fixdep: No such file or directory
Luckily it can easily be reproduced locally via a simple script so it was
not hard to bisect it down to upstream commit [1].
However, its not that commits fault, it just uncovered an issue with the
way we have been building envtools for a long time, maybe even from the
package introduction.
The issue is that we are trying to build envtools as one of the U-Boot
no-dot-config-targets but envtools was newer a valid target for it but
since we were creating the config headers that were not actually used it
was actually building all this time.
Since the blamed commit [1] a tool called printinitialenv is built and
now a proper config is actually required in order for prerequisites to
get built properly.
So, in order to properly fix this (Hopefully for good) lets stop pretending
that envtools are a valid no-dot-config-targets target and use the
tools-only defconfig which is meant exactly for just building the tools.
This will make a minimal config for the U-Boot sandbox target and then
envtools will build just fine in parallel mode (I tested with 32 threads).
We do hovewer need to override the ARCH passed by OpenWrt and set it to
sandbox as otherwise U-Boot will not find the required headers because the
ARCH is being overriden to an incorrect one.
[1] 40b77f2a3a
Fixes: 9db0330052 ("uboot-envtools: update to 2023.07.02")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Fix compatible string to match what is supported upstream, fix alignment
and order MTD partitions according to offset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Telenor quirks
--------------
The operator specific firmware running on the Telenor branded
ZyXEL EX5700 includes U-Boot modifications affecting the OpenWrt
installation.
Notable changes to U-Boot include
- environment is stored in RAM and reset to defaults when power
cycled
- dual partition scheme with "nomimal" or "rescue" systems, falling
back to "rescue" unless the OS signals success in 3 attempts
- several runtime additions to the device-tree
Some of these modifications have side effects requiring workarounds
- U-Boot modifies /chosen/bootargs in an unsafe manner, and will crash
unless this node exists
- U-Boot verifies that the selected rootfs UBI volume exists, and
refuses to boot if it doesn't. The chosen "rootfs" volume must contain
a squashfs signature even for tftp or initramfs booting.
- U-Boot parses the "factoryparams" UBI volume, setting the "ethaddr"
variable to the label mac. But "factoryparams" does not always
exist. Instead there is a "RIP" volume containing all the factory
data. Copying the "RIP" volume to "factoryparams" will fix this
Hardware
--------
SOC: MediaTek MT7986
RAM: 1GB DDR4
FLASH: 512MB SPI-NAND (Mikron xxx)
WIFI: Mediatek MT7986 802.11ax 5 GHz
Mediatek MT7916 DBDC 802.11ax 2.4 + 6 GHz
ETH: MediaTek MT7531 Switch + SoC
3 x builtin 1G phy (lan1, lan2, lan3)
2 x MaxLinear GPY211C 2.5 N-Base-T phy (lan4, wan)
USB: 1 x USB 3.2 Enhanced SuperSpeed port
UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC)
Installation
------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.2/24. Rename the image to C0A80101.img.
2. Connect the TFTP server to lan1, lan2 or lan3. Connect to the serial
console, Interrupt the autoboot process by pressing ESC when prompted.
3. Download and boot the OpenWrt initramfs image.
$ env set uboot_bootcount 0
$ env set firmware nominal
$ tftpboot
$ bootm
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
----------------
- The "lan1", "lan2" and "lan3" port LEDs are driven by the switch but
OpenWrt does not correctly configure the output.
- The "lan4" and "wan" port LEDs are driven by the GPH211C phys and
not configured by OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
Update to the latest stable version.
This update changes the default lockfile directory from /var/lock to
/run [1]. In OpenWRT we still use the "legacy" /var/lock and /run might
not even exist, so we add a patch to revert this particular change.
[1] aeb40f1166
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Because this device enable NMBM by default, most users use custom
U-Boot with NMBM-Enabled in Chinese forums.
This layout is the same as the ubootmod layout but enabling NMBM.
Signed-off-by: Hank Moretti <mchank9999@gmail.com>
This is the first commit to introduce the base for the N821 board used
in Cisco vEdge 1000.
This commit does not include the custom CPLD drivers but rather
everything else that is already present in the upstream kernel.
This results in an image that boots, but e.g. the SFP ports are not
usable.
Hardware:
- CPU: Cavium Networks CN6130, 4 cores @ 1.0 GHz
- Flash:
- 16 MiB SPI NOR presented as 2x8 MiB for A/B boot recovery
- 8192 MiB eMMC
- RAM: 4096 MiB
- Ethernet 1Gbit ports: 1x
- Ethernet SFP ports: 8x
- USB ports: 2x 3.0 Type-A on front panel
- Serial: Two, one internal and one external
- JTAG: Yes
- LED count: 18x
- Button count: 1x
- GPIOs: 1x
- Power: 2x redundant DC 12V barrel plug
- Extra: Slot for SD card on front
See the OpenWrt wiki for more hardware details.
Installation:
- Flash squashfs to /dev/sda2 and put kernel on /dev/sda1.
- Update uboot's bootcmd environment variable to match.
Full installation guide will be added to OpenWrt wiki when sysupgrade
support is added.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Signed-off-by: Tommy Nevtelen <tommy@nevtelen.com>
Tested-by: Viktor Ekmark <viktor@ekmark.se>
Tested-by: Daniel Wennberg <github@networkninja.se>
ASUS RT-AC59U / RT-AC59U v2 are wi-fi routers with a large number of
alternate names, including RT-AC1200GE, RT-AC1300G PLUS, RT-AC1500UHP,
RT-AC57U v2/v3, RT-AC58U v2/v3, and RT-ACRH12.
ASUS ZenWiFi AC Mini(CD6) is a mesh wifi system. The unit labeled CD6R
is the router, and CD6N is the node.
Hardware:
- SoC: QCN5502
- RAM: 128 MiB
- UART: 115200 baud (labeled on boards)
- Wireless:
- 2.4GHz: QCN5502 on-chip 4x4 802.11b/g/n
currently unsupported due to missing support for QCN550x in ath9k
- 5GHz: QCA9888 pcie 5GHz 2x2 802.11a/n/ac
- Flash: SPI NOR
- RT-AC59U / CD6N: 16 MiB
- RT-AC59U v2 / CD6R: 32 MiB
- Ethernet: gigabit
- RT-AC59U / RT-AC59U v2: 4x LAN 1x WAN
- CD6R: 3x LAN 1x WAN
- CD6N: 2x LAN
- USB:
- RT-AC59U / RT-AC59U v2: 1 port USB 2.0
- CD6R / CD6N: none
WiFi calibration data contains valid MAC addresses.
The initramfs image is uncompressed because I was unable to boot a
compressed initramfs from memory (gzip or lzma). Booting a compressed
image from flash works fine.
Installation:
To install without opening the case:
- Set your computer IP address to 192.168.1.10/24
- Power up with the Reset button pressed
- Release the Reset button after about 5 seconds or until you see the
power LED blinking slowly
- Upload OpenWRT factory image via TFTP client to 192.168.1.1
Revert to stock firmware using the same TFTP method.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
This commit adds support for following wireless routers:
- Beeline SmartBox PRO (Serсomm S1500 AWI)
- WiFire S1500.NBN (Serсomm S1500 BUC)
This commit is based on this PR:
- Link: https://github.com/openwrt/openwrt/pull/4770
- Author: Maximilian Weinmann <x1@disroot.org>
The opening of this PR was agreed with author.
My changes:
- Sorting, minor changes and some movings between dts and dtsi
- Move leds to dts when possible
- Recipes for the factory image
- Update of the installation/recovery/return to stock guides
- Add reset GPIO for the pcie1
Common specification
--------------------
SoC: MediaTek MT7621AT (880 MHz, 2 cores)
Switch: MediaTek MT7530 (via SoC MT7621AT)
Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2
Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2
Ethernet: 5 ports - 5×GbE (WAN, LAN1-4)
Mini PCIe: via J2 on PCB, not soldered on the board
UART: J4 -> GND[], TX, VCC(3.3V), RX
BootLoader: U-Boot SerComm/Mediatek
Beeline SmartBox PRO specification
----------------------------------
RAM (Nanya NT5CB128M16FP): 256 MiB
NAND-Flash (ESMT F59L2G81A): 256 MiB
USB ports: 2xUSB2.0
LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP)
Power: 12 VDC, 1.5 A
PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0
CSN: SG15********
MAC LAN: 94:4A:0C:**:**:**
Manufacturer's code: 0AWI0500QW1
WiFire S1500.NBN specification
------------------------------
RAM (Nanya NT5CC64M16GP): 128 MiB
NAND-Flash (ESMT F59L1G81MA): 128 MiB
USB ports: 1xUSB2.0
LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet
Buttons: 2 button (RESET, WPS)
Power: 12 VDC, 1.0 A
PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0
CSN: MH16********
MAC WAN: E0:60:66:**:**:**
Manufacturer's code: 0BUC0500RW1
MAC address table (PRO)
-----------------------
use address source
LAN *:23 factory 0x1000 (label)
WAN *:24 factory $label +1
2g *:23 factory $label
5g *:25 factory $label +2
MAC addresses (NBN)
-------------------
use address source
LAN *:0e factory 0x1000
WAN *:0f LAN +1 (label)
2g *:0f LAN +1
5g *:10 LAN +2
OEM easy installation
---------------------
1. Remove all dots from the factory image filename (except the dot
before file extension)
2. Upload and update the firmware via the original web interface
3. Two options are possible after the reboot:
a. OpenWrt - that's OK, the mission accomplished
b. Stock firmware - install Stock firmware (to switch booflag from
Sercomm0 to Sercomm1) and then OpenWrt factory image.
Return to Stock
---------------
1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:
printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2
reboot
2. Install stock firmware via the web OEM firmware interface
Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery
Tested-by: Pavel Ivanov <pi635v@gmail.com>
Tested-by: Denis Myshaev <denis.myshaev@gmail.com>
Tested-by: Oleg Galeev <olegingaleev@gmail.com>
Tested-By: Ivan Pavlov <AuthorReflex@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The Traverse LS1043 boards were not publicly released,
all the production has been going to OEM customers who
do not use the image format defined in the OpenWrt tree.
Only a few samples were circulated outside Traverse
and our OEM customers. The public release (then called
Five64) of this series was cancelled in favour of our
LS1088A based design (Ten64).
It is best to remove these boards to avoid wasting
OpenWrt project and contributor resources.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac
(Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work
currently as there is no driver.
Related: https://github.com/openwrt/openwrt/pull/5084
For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2.
Specifications:
* MT7629, 256 MiB RAM, 16 MiB SPI NOR
* MT7761N (2.4GHz) / MT7762N (5GHz) - no driver
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* After installation, perform a factory reset. Wait for the device to
boot, then hold the reset button for 10 seconds. This is needed
because sysupgrade in the stock firmware will attempt to preserve its
configuration using sysupgrade.tgz.
See https://github.com/openwrt/openwrt/pull/4182
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
Netgear EAX12, EAX11v2, EAX15v2 are wall-plug 802.11ax (Wi-Fi 6)
extenders that share the SoC, WiFi chip, and image format with the
WAX202.
Specifications:
* MT7621, 256 MiB RAM, 128 MiB NAND
* MT7915: 2.4/5 GHz 2x2 802.11ax (DBDC)
* Ethernet: 1 port 10/100/1000
* UART: 115200 baud (labeled on board)
All LEDs and buttons appear to work without state_default.
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References in GPL source:
https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz
* target/linux/ramips/dts/mt7621-rfb-ax-nand.dts
DTS file for this device.
Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
