Commit Graph

27395 Commits

Author SHA1 Message Date
Stijn Tintel
230f2fccd1 qoriq: switch to kernel 5.15
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-14 18:53:39 +02:00
Christian Marangi
823ddab80e
ipq806x: 5.15: standardize wpq864 partition table
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.

Also add "0:" to each qcom default partition following smem naming.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-14 02:23:22 +01:00
Christian Marangi
266b261d39
ipq806x: 5.15: fix wrong boot-partitions values for split partitions
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.

Fix it to the correct format in each affected dts.

Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-14 02:23:22 +01:00
Andrew Cameron
550e5b2184 ath79: add support for TP-Link CPE605-v1
TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps Ethernet
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 23dBi high-gain directional antenna and a dedicated metal reflector
 - Power, LAN, WLAN5G green LEDs
 - 3x green RSSI LEDs

Flashing instructions:
 Flash factory image through stock firmware WEB UI or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2022-12-13 23:17:27 +01:00
Mikhail Zhilkin
0ec8d991c2 ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1.  Login to the router web interface under admin account
2.  Navigate to Settings -> Configuration -> Save to Computer
3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
       cfgtool.py -u configurationBackup.cfg
4.  Open configurationBackup.xml and find the following line:
    <PARAMETER name="Password" type="string" value="<your router serial \
       is here>" writable="1" encryption="1" password="1"/>
5.  Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml
7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router
8.  Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
    ETxxxxxxxxxx is the serial number from the backplate label)
9.  Navigate to Settings -> WAN -> Add static IP interface (e.g.
    10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
    10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
    ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
       sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
       printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
       reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 10.0.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:50    |
| WAN | label + 11 | *:5b    |
| 2g  | label + 2  | *:52    |
| 5g  | label + 3  | *:53    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-12-13 23:06:20 +01:00
Christian Marangi
05dbdcbd32
generic: move pending 870 ca8210 fix crash patch to backport
Patch got merged upstream in kernel 6.1. Move it to backport to better
track it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-13 02:05:29 +01:00
Christian Marangi
c3c9ef598c
generic: fix wrong PTR_ERR use in of net mac address ascii patch
nvmem_cell_read return a pointer error when an error occurs. Currently
we convert the pointer error to an int while the rest of the function
return a void* and expcet an error pointer. Fix this PTR_ERR msuse
fixing compilation warning.

Fixes the following compilation warning:
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address':
net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
  547 |                 return PTR_ERR(mac);
      |                        ^~~~~~~~~~~~
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii':
net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
  564 |                 return PTR_ERR(mac_ascii);
      |                        ^~~~~~~~~~~~~~~~~~

Fixes: 7b863af180 ("kernel: move mac-address-ascii patches to generic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-13 00:33:19 +01:00
Linus Walleij
772434e707 gemini: Set proper default networks
Some Gemini devices are NAS type devices and need to ask for
DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible
defaults for all known devices.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-12-12 11:18:02 +01:00
Christian Lamparter
50d20db6a8 uml: switch to Kernel 5.15
Switch over from testing version.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Christian Lamparter
f6c61571fb bcm53xx: remove MR32's openwrt specific patch for LEDs
The patch managed to sneak into v5.15 whereas it was
properly deleted for v5.10.

Fixes: 8f6e2bb178 ("bcm53xx: remove MR32's specific get_leds_dt code")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Chukun Pan
b40a047f1f sunxi: fix sunxi-ir kconfig and description
Removed a20 in description, since it
only works for a10, a13 and a31.
Also refreshed kernel config.

Fixes: #10466
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(moved fixes, refreshed, added CONFIG_DVB_USB=n)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Chukun Pan
a125d46a28 sunxi: modules: remove useless AddDepends/rtc
AddDepends/rtc has been removed in commit 3da7fe6, same here.
Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction")

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(RTC_SUPPORT - though this is implied by the TARGET_sunxi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Tony Butler
1e240f60a5 kernel: modules/lib-lz4: add lz4hc_compress
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config

this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor

Signed-off-by: Tony Butler <spudz76@gmail.com>
2022-12-11 09:32:53 -08:00
Tony Butler
9a1ab8aa03 lantiq: vr9: include usb driver for fritz 7430
Reported by user: missing driver for USB; add to image definition
https://github.com/openwrt/openwrt/issues/11326

Resolves: #11326

Signed-off-by: Tony Butler <spudz76@gmail.com>
Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-12-11 16:46:34 +01:00
Hauke Mehrtens
2484f0951c kernel: Refresh kernel 5.10
Make the patches apply cleanly again.

Fixes: 8327e0fb72 ("kernel: backport the dev_set_threaded export to 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-11 16:42:16 +01:00
Weiping Yang
1c169d28ff ipq40xx: fix usb driver not loaded for GL-A1300
This patch enables USB support for the GL.iNet GL-A1300
Repair the usb driver startup phase is not loaded

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2022-12-11 03:06:54 +01:00
John Audia
6801c460b6 kernel: bump 5.10 to 5.10.158
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
7b7d8fe60d kernel: bump 5.10 to 5.10.157
Manually rebased:
	backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch
	hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch

Removed upstreamed:
	pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
f83a8329a3 kernel: add symbol in generic config for 5.10.157
Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
68426e54ed kernel: bump 5.15 to 5.15.82
All patches automatically rebased.

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
John Audia
424210b7be kernel: bump 5.15 to 5.15.81
Manually rebased:
	backport-5.15/715-v6.0-net-ethernet-mtk_eth_soc-add-the-capability-to-run-m.patch
	hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch[1]

Removed upstreamed:
	pending-5.15/701-netfilter-nf_flow_table-add-missing-locking.patch[2]

All other patches automatically rebased

1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk>
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a

Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
John Audia
2b375b7db4 kernel: add symbol in generic config for 5.15.81
Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:42:52 +01:00
Felix Fietkau
8327e0fb72 kernel: backport the dev_set_threaded export to 5.10
Fixes mt76 build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 17:36:12 +01:00
Felix Fietkau
5f2d471279 kernel: backport mtk_wed.h from 5.15 to 5.10
Fixes mt76 build error

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-12-10 17:30:36 +01:00
David Bauer
4c0919839d ath79: fix Teltonika RUT230 v1 MAC assignment
The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the
LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi
MAC is printed on the case as part of the SSID, however only the LAN
MAC-Address is designated as a MAC-Address.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-12-09 01:59:47 +01:00
Jan-Niklas Burfeind
dbc93d280c realtek: update GPIO bindings for DGS-1210-10P
add three missing LEDs
 - PoE-Max
 - Link/Act
 - PoE

add two missing buttons
 - mode
 - reset

The last was dropped in
commit 61a3d0075b ("realtek: update GPIO bindings in the dts files in dts-5.10")

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
2022-12-09 00:13:51 +01:00
Andreas Böhler
3e7e4d0b97 realtek: d-link: add support for dgs-1210-28mp-f
General hardware info:
----------------------

D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz,
DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 370W.

Power over Ethernet:
--------------------

The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU.
In order to enable PoE, the realtek-poe package is required. It is
installed by default, but currently it requires the manual editing of
/etc/config/poe. Keep in mind that the port number assignment does not
match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and
24-17.

LEDs and Buttons:
-----------------

On stock firmware, the mode button is supposed to switch the LED indicators
of all port LEDs between Link Activity and PoE status. The currently
selected mode is visualized using the respective LEDs. PoE Max indicates
that the maximum PoE budget has been reached.
Since there is currently no support for this behavior, these LEDs and
the mode button can be used independently.

Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.

Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd

OEM installation from Web Interface:
------------------------------------

  1. Make sure you are booting using OEM in image 2 slot. If not, switch to
     image2 using the menus
        System > Firmware Information > Boot from image2
        Tools > reboot
  2. Upload image in vendor firmware via Tools > Backup / Upgrade
     Firmware > image1
  3. Toogle startup image via System > Firmware Information > Boot from
     image1
  4. Tools > reboot

Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:

Boot initramfs image from U-Boot:
---------------------------------

  1. Press Escape key during `Hit Esc key to stop autoboot` prompt
  2. Press CTRL+C keys to get into real U-Boot prompt
  3. Init network with `rtk network on` command
  4. Load image with `tftpboot 0x8f000000
     openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin`
     command
  5. Boot the image with `bootm` command

Signed-off-by: Andreas Böhler <dev@aboehler.at>
2022-12-08 21:51:43 +01:00
Jan-Niklas Burfeind
dce66899bf ramips: add support for Wavlink WS-WN572HP3 4G
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.

Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
  * MT7613BEN: 5GHz
  * MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
  * 7 blue at the front
    * 1 Power
    * 2 LAN / WAN
    * 1 Status
    * 3 RSSI (annotated 4G)
  * 1 green at the bottom (4G LED)
* Buttons: 1 reset button

Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
  least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
  until the device reboots

Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
2022-12-07 12:30:45 +01:00
David Bauer
bc14925f3d ramips: define loadaddr for all UniFi devices
Define the load-address for the DTB of all Ubiquiti UniFi devices using
FIT images. From the GPL code we can assume these boards are affected by
the same relocating issue with the vendor bootloader.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-12-07 12:30:29 +01:00
Daniel Golle
2307b049e4
mediatek: also move &slot0 from dtsi down to board dts
As the referenced MTD partition is only present in the dts, also move
&slot0 down to the dts files.

Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi")
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-07 01:45:14 +00:00
Daniel Golle
9d22ab703f mediatek: remove redundant flash entry from dtsi
Splitting-off the common parts of Ruijie RG-EW3200GX PRO and
reyee AX3200-E5 went wrong because the flash descriptiom was kept
also in the dtsi. Remove it there, as flash definition is added by
both board dts files.

Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-07 00:46:26 +00:00
Shiji Yang
3c1512a25d ath79: optimize the firmware recipe for Netgear NAND devices
1. Drop useless character '0xff' before fake filesystem header.
2. Reduce useless padding to shrink the size of the sysupgrade image.
3. Do not check the size of sysupgrade image. It does not make sense to
   check the size of a compressed package.
4. Do not take the size of netgear header into account because it will
   not be written to Flash.
5. Use the default lzma compression dictionary parameter '-d24' to get
   better performance.

Tested on Netgear R6100
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-06 23:11:23 +01:00
Shiji Yang
58088ff457 ath79: convert Netgear R6100 radio calibration to nvmem-cells
use nvmem-cells implementation to avoid copying art calibration data
to rootfs.

Tested on Netgear R6100
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-12-06 23:11:23 +01:00
Hauke Mehrtens
48025b8ac9 kernel: ca8210: Fix crash by zero initializing data
This fixes crashes at bootup on pistachio.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-06 23:09:48 +01:00
Alex Hansen
7dbac3433f mediatek: add support for reyee AX3200-E5
This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly
different flash layout, install process is the same.

Specifications:
SoC: MT7622B
RAM: 256MB
Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR
Ethernet: 5x1GbE
Switch: MT7531BE
WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN
3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red)
2Keys: Mesh button + Reset button
UART: Marked J19 on board. 3.3v, 115200n1
Power: 12V 2.5A

Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
    dd if=/dev/mtd7 of=/tmp/firmware.bin
    and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.

Recovery stock firmware:

1. Transfer the firmware.bin image to the device.
2. Flash the image with:
    mtd write firmware.bin firmware

Signed-off-by: Alex Hansen <mralexh123@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-06 12:43:15 +00:00
Joonhyuk Song
25ede5170d ramips: mt7621: enable lzma-loader for netis WF2881
Fixes boot loader LZMA decompression issues (LZMA ERROR 1)

Signed-off-by: Joonhyuk Song <thenoface303@gmail.com>
2022-12-06 01:51:00 +01:00
John Thomson
7ea965b578 ramips: mt7621: mikrotik 760igs (hEX S) fix SFP
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.

Fixes: c77858aa79 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
2022-12-06 01:47:36 +01:00
Daniel Golle
83f20fc9f7 mediatek: mt7623: build mt6577_auxadc driver into kernel
Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the
thermal-zone doesn't work on MT7623 (it does work fine without this
driver on MT7622 and MT7986).

Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-12-05 23:14:36 +00:00
INAGAKI Hiroshi
a224412bbc ramips: use ARTIFACTS for initramfs-factory of I-O DATA WN-AX1167GR
Use ARTIFACTS to generate initramfs-based factory image of I-O DATA
WN-AX1167GR instead of redundant recipe which generate on
KERNEL_INITRAMFS.

Note:

WN-AX1167GR has 2x OS images on stock firmware.

stock log:

flash manufacture id: c2, device id 20 18
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 10 MTD partitions on "raspi":
0x000000000000-0x000001000000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config "
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000000060000 : "iNIC_rf"
0x000000060000-0x0000007e0000 : "Kernel"
0x000000800000-0x000000f80000 : "app"
0x000000f90000-0x000000fa0000 : "Key"
0x000000fa0000-0x000000fb0000 : "backup"
0x000000fb0000-0x000001000000 : "storage"

1st image is "Kernel" and 2nd is "app" when booted from 1st image.
In OpenWrt, those 2x partitions are combined to "firmware" with
undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff).

The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so
check-size for initramfs-factory image needs to be called with the size.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-05 01:28:28 +00:00
Senis John
a8f3c97ce8 ramips: add support for HiWiFi HC5611
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1

1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`

I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot

Signed-off-by: Senis John <thank243@gmail.com>
2022-12-04 15:21:12 +08:00
Kien Truong
d11d93b9ae rockchip: enable watchdog driver
Enable Synopsys DesignWare watchdog driver for rockchip device

Tested on NanoPi R2S

Signed-off-by: Kien Truong <duckientruong@gmail.com>
2022-12-04 15:21:12 +08:00
Petr Štetiar
97c77fff28 Revert "mvebu: switch default kernel to 5.15"
This reverts commit 5429411f73 as upstream
in commit e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies") has
changed `PTP_1588_CLOCK` dependency handling in 5.15 kernel.

That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced
by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in
those builds, which leads to a broken LAN bridge network on several
devices.

References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-12-04 08:16:49 +01:00
Bjørn Mork
8719f73fa2 ramips: mt7621: enable lzma-loader for ZyXEL WAP6805
Fixing "Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board
to recover".

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2022-12-03 21:04:38 +01:00
Stijn Segers
5429411f73 mvebu: switch default kernel to 5.15
In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu
to 5.15 which has been the testing kernel on this target since April - over
half a year.

Run-tested on the following subtargets:
* cortexa9 (Turris Omnia - 03f41b1eb2)
* cortexa72 (MikroTik RB5009UG+S+IN)

Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000]
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2022-12-02 16:57:48 +01:00
Jan-Niklas Burfeind
a5873ad675 realtek: fix dell typo
should be add/delete or abbreviated add/del

Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
2022-12-01 22:49:23 +01:00
Luiz Angelo Daros de Luca
ed9bd9824a realtek: refactor keep vlan tag setup, fix tagged forwarding
The code in dsa.c:rtl83xx_port_enable() was trying to set
vlan_port_tag_sts_ctrl while dealing with differences between SoCs.
However, not only that register has a different address, the register
structure and even the 2-bit value semantic changes for each SoC.

The vlan_port_tag_sts_ctrl field was dropped and converted into a
vlan_port_keep_incoming_tag_set() function that abstracts the different
between SoCs. The macro referencing that register migrated to the SoC
specific c file as it will be privately used by each file.

All magic numbers were converted into macros using BITMASK and
FIELD_PREP.

The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already
broken for rtl93xx. The best place for SoC specific code might be in each
respective c file and not in if/else clauses.

The final result is:

rtl838x: set ITAG_STS=TAGGED, same as before
rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing
	 forwarding of tagged packets
rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly
	 fixing forwarding of tagged packets
rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly
         fixing forwarding of tagged packets

Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets
will drop the vlan tag while packets from the CPU will still have the
correct tag.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2022-12-01 22:15:55 +01:00
Olliver Schinagl
59542c9ac9 realtek: Fix rtl930x speed status accessor
The rtl930x speed status registers require 4 bits to indicate the speed
status. As such, we want to divide by 8. To make things consistent with
the rest of this code, use a bitshift however.

This bug probably won't affect many users yet, as there aren't many
rtl930x switches in the wild yet with more then 10 ports, and thus a
low-impact bugfix.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[also fix port field extraction]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-01 22:11:06 +01:00
Alexander Couzens
d4c460648d
ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6
The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP
with a miniPCIe slot for a LTE modem.
The wAP R AC is similar to the wAP AC but with the miniPCIe slot.
The wAP R AC requires installing a LTE modem.
The wAP LTE and wAP LTE6 comes with a LTE modem installed.

See https://mikrotik.com/product/wap_r_ac for more info.

Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless:
   - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna
   - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports
  one with 802.3af/at PoE in
- 1x Mini PCI-E port (USB2)

Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
2022-11-27 13:28:22 +00:00
Aleksander Jan Bajkowski
bb2fb4f16a airoha: disable swconfig
Swconfig isn't used by this target and can be disabled for
this reason. Airoha doesn't even have an Ethernet driver.
In the future, this target should get a DSA driver.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-27 13:18:29 +01:00
Aleksander Jan Bajkowski
d81e948dc2 airoha: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=platform

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
5b0e111789 layerscape: kmod-ppfe: Use ppfe driver as module
In 8274451cb86 kmod-ppfe was changed to built-in because CONFIG_FSL_PPFE
was binary. In 5.10 and 5.15 kernel, PPFE driver can be build as module.

This patch switch kmod-ppfe from build-in to loadable module.
Loadable module helps to avoid hazard: driver is looking for firmware
file before mount root.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
23b9b01cdd layerscape: switch kernel testing to 5.15
Let's test layerscape with 5.15 kernel.

Run tested: LS1012A-FRDM, LS1046A-RDB (nor and sd-boot images),
	    LS1021A-IOT (By @ArtelMike with u-boot fix)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
afcccaad82 layerscape: Switch LS1012A-FRDM initramfs to gzip
At this moment LS1012A-FRDM have uncompressed initramfs image.

Error was caused, because gzip extract area overlap image.

Let's change loadaddr and enable gzip initramfs images again.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
d64d1c86cc layerscape: remove kernel 5.4 dependences
5.4 kernel was removed. Let's clean old dependences.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
a42edce9fd layerscape: 5.15: refresh kernel config
Done by 'make kernel_oldconfig'.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
8efffce677 layerscape: copy patches 5.10 to 5.15
One patch manually rebased:
302-arm64-dts-ls1012a-update-with-ppfe-support.patch

PFE driver patch recreated from NXP 5.15 tree:
701-staging-add-fsl_ppfe-driver.patch

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
f620fb4b73 layerscape: copy config 5.10 to 5.15
Configs was just copied.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
2268d55521 layerscape: refresh kernel config
Done by 'make kernel_oldconfig'.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Pawel Dembicki
2e4fe289ce layerscape: Fix SPI-NOR issues with vendor patches
For some reason LS1012A and LS1046A devboards don't work well with
Spansion SPI NOR flash. It cause read and write errors like:

[   27.285887] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x025ae000
[   27.468922] jffs2: Newly-erased block contained word 0x0 at offset 0x02573000
[   27.502615] jffs2: Newly-erased block contained word 0xe723f41e5823f110 at offset 0x02572000
[   27.541550] jffs2: Newly-erased block contained word 0x1a7d266ee6 at offset 0x02571000
[   27.577195] jffs2: Newly-erased block contained word 0x5d000bae8d52fec6 at offset 0x02570000
[   27.611800] jffs2: Newly-erased block contained word 0x63515aee63515a4b at offset 0x0256f000
[   27.651749] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0256e000
[   27.825593] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0252e000

NXP have found workarround and applied in their vendor kernel version.
They force 1x tx and 1x rx lines in qspi. That method fix issues.
This patch ports patches from NXP LSDK tree.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-11-27 13:18:29 +01:00
Will Moss
a58146d452 ath79: D-Link DIR-825 B1 add factory.bin recipe
- Bring back factory.bin image which was missing after porting device to ath79 target
- Use default sysupgrade.bin image recipe
- Adjust max image size according to new firmware partition size after
"ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes
- Remove support of upgrading from version 19.07, because partition size changes mentioned above

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-27 13:18:29 +01:00
Michael Pratt
6de9287abd ath79: add support for Senao Engenius EAP1750H
FCC ID: A8J-EAP1750H

Engenius EAP1750H is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+

**Specification:**

  - QCA9558 SOC
  - QCA9880 WLAN	PCI card, 5 GHz, 3x3, 26dBm
  - AR8035-A PHY	RGMII GbE with PoE+ IN
  - 40 MHz clock
  - 16 MB FLASH		MX25L12845EMI-10G
  - 2x 64 MB RAM	NT5TU32M16FG
  - UART at J10		populated
  - 4 internal antenna plates (5 dbi, omni-directional)
  - 5 LEDs, 1 button (power, eth0, 2G, 5G, WPS) (reset)

**MAC addresses:**

  MAC addresses are labeled as ETH, 2.4G, and 5GHz
  Only one Vendor MAC address in flash

  eth0 ETH  *:fb art 0x0
  phy1 2.4G *:fc ---
  phy0 5GHz *:fd ---

**Serial Access:**

  the RX line on the board for UART is shorted to ground by resistor R176
  therefore it must be removed to use the console
  but it is not necessary to remove to view boot log

  optionally, R175 can be replaced with a solder bridge short

  the resistors R175 and R176 are next to the UART RX pin at J10

**Installation:**

  2 ways to flash factory.bin from OEM:

  Method 1: Firmware upgrade page:

    OEM webpage at 192.168.1.1
    username and password "admin"
    Navigate to "Firmware Upgrade" page from left pane
    Click Browse and select the factory.bin image
    Upload and verify checksum
    Click Continue to confirm and wait 3 minutes

  Method 2: Serial to load Failsafe webpage:

    After connecting to serial console and rebooting...
    Interrupt uboot with any key pressed rapidly
    execute `run failsafe_boot` OR `bootm 0x9fd70000`
    wait a minute
    connect to ethernet and navigate to
    "192.168.1.1/index.htm"
    Select the factory.bin image and upload
    wait about 3 minutes

**Return to OEM:**

  If you have a serial cable, see Serial Failsafe instructions
  otherwise, uboot-env can be used to make uboot load the failsafe image

  ssh into openwrt and run
  `fw_setenv rootfs_checksum 0`
  reboot, wait 3 minutes
  connect to ethernet and navigate to 192.168.1.1/index.htm
  select OEM firmware image from Engenius and click upgrade

**TFTP recovery:**

  Requires serial console, reset button does nothing

  rename initramfs to 'vmlinux-art-ramdisk'
  make available on TFTP server at 192.168.1.101
  power board, interrupt boot
  execute tftpboot and bootm 0x81000000

  NOTE: TFTP is not reliable due to bugged bootloader
  set MTU to 600 and try many times
  if your TFTP server supports setting block size
  higher block size is better.

**Format of OEM firmware image:**

  The OEM software of EAP1750H is a heavily modified version
  of Openwrt Kamikaze. One of the many modifications
  is to the sysupgrade program. Image verification is performed
  simply by the successful ungzip and untar of the supplied file
  and name check and header verification of the resulting contents.
  To form a factory.bin that is accepted by OEM Openwrt build,
  the kernel and rootfs must have specific names...

    openwrt-ar71xx-generic-eap1750h-uImage-lzma.bin
    openwrt-ar71xx-generic-eap1750h-root.squashfs

  and begin with the respective headers (uImage, squashfs).
  Then the files must be tarballed and gzipped.
  The resulting binary is actually a tar.gz file in disguise.
  This can be verified by using binwalk on the OEM firmware images,
  ungzipping then untaring.

  Newer EnGenius software requires more checks but their script
  includes a way to skip them, otherwise the tar must include
  a text file with the version and md5sums in a deprecated format.

  The OEM upgrade script is at /etc/fwupgrade.sh.

  OKLI kernel loader is required because the OEM software
  expects the kernel to be no greater than 1536k
  and the factory.bin upgrade procedure would otherwise
  overwrite part of the kernel when writing rootfs.

Note on PLL-data cells:

  The default PLL register values will not work
  because of the external AR8035 switch between
  the SOC and the ethernet port.

  For QCA955x series, the PLL registers for eth0 and eth1
  can be see in the DTSI as 0x28 and 0x48 respectively.
  Therefore the PLL registers can be read from uboot
  for each link speed after attempting tftpboot
  or another network action using that link speed
  with `md 0x18050028 1` and `md 0x18050048 1`.

  The clock delay required for RGMII can be applied
  at the PHY side, using the at803x driver `phy-mode`.
  Therefore the PLL registers for GMAC0
  do not need the bits for delay on the MAC side.
  This is possible due to fixes in at803x driver
  since Linux 5.1 and 5.3

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
Michael Pratt
128947db42 ath79: use nvmem-cells for radio calibration of EAP1200H
Transition from userscript to DTS for all of ART.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2022-11-27 13:18:29 +01:00
Edward Chow
2c33fd39a5 ath79: calibrate TP-LINK TL-WR2543ND with nvmem
Driver for and pci wlan card now pull the calibration data from the nvmem
subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my tplink tl-wr2543nd.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-27 13:18:29 +01:00
John Audia
acb10faa35 kernel: bump 5.10 to 5.10.156
Manually rebased: ath79/patches-5.10/910-unaligned_access_hacks.patch

All other patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-27 13:18:29 +01:00
John Audia
590aa0ca51 kernel: bump 5.15 to 5.15.80
Manually rebase:
   pending-5.15/330-MIPS-kexec-Accept-command-line-parameters-from-users.patch
   ath79/patches-5.15/910-unaligned_access_hacks.patch

All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-27 13:18:29 +01:00
Christian Marangi
60fc93b359
ipq806x: disable cache and fabric devfreq driver to improve stability
It was tested that cache scaling currently cause instability problem.
This is probably caused by a latent misconfiguration that cause the L2
cache to be sourced from the wrong source and runs at an unstable freq
compared to the original QSDK fw.

To improve stability while the problem is bisected, disable the devfreq
drivers with minimal perf penality.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-11-26 00:38:31 +01:00
Felix Fietkau
3dff6b53db kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break

Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-25 01:56:53 +01:00
Daniel Golle
c1d1202e67
mediatek: set persistent wifi mac for bpi-r64 and bpi-r3
Use persistent MAC address for the built-in wireless interfaces of the
BPi-R64 and BPi-R3 development boards.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:33 +00:00
Daniel Golle
87fc485450
ipq40xx: remove '-fit' string from kernel filenames
The type of those images is already distinguishable by the '.itb'
extension, there is no need for an additional '-fit' string in the
filenames. Remove it to behave more like other targets.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:28 +00:00
Daniel Golle
d9f7c751c9
ipq40xx: remove 'nand-' string from image filenames
Only on the ipq40xx subtarget different filenames were used for NAND-
based devices. This is unneeded, confusing and breaks downstream tools
such as luci-app-attendedsysupgrade and auc.
Remove the 'nand-' string from image filenames to fix that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-11-24 16:46:18 +00:00
Edmunt Pienkowsky
c34eab6fd1 bcm27xx: sound-soc-justboom-*: fix packages
Affected packages: sound-soc-justboom-both, sound-soc-justboom-dac and sound-soc-justboom-digi.

- Add snd-soc-wm8804-i2c and/or snd-soc-pcm512x-i2c kernel modules.
- Add kmod-regmap-i2c package dependency.

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
2022-11-23 20:17:21 +01:00
Edmunt Pienkowsky
0889adf16f bcm27xx: sound-soc-hifiberry-digi: fix package
- Add snd-soc-wm8804-i2c kernel module,
- Add kmod-regmap-i2c package dependency.

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
2022-11-23 20:17:18 +01:00
John Audia
3f7cc9d014 bcm27xx: disable duplicate sdhost driver
Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this
error in dmesg:
Error: Driver 'sdhost-bcm2835' is already registered, aborting...

Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled
avoids this error.

Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
[Disable driver for all subtargets, refresh configs, tweak description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-23 20:13:46 +01:00
Felix Fietkau
eaba63cdde kernel: fix regression on mt7986
The CDMQ ingress special tag flag needs to be set for 7986 even without DSA
untag offload, otherwise tx checksum offload seems to break

Fixes: 9b482ee22f ("kernel: add more fixes for mtk_eth_soc")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-23 11:34:43 +01:00
Felix Fietkau
4e1a6ee903 kernel: add WED rx support for mediatek
This is required for rx flow offloading on mt76 with MT7986 and MT7915

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 20:46:47 +01:00
Felix Fietkau
e410833bdd kernel: add a locking fix for netfilter hardware flow offloading
Protect the flow block cb list readers against concurrent updates

Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 20:44:01 +01:00
Felix Fietkau
9b482ee22f kernel: add more fixes for mtk_eth_soc
Fix corner cases in DSA offload
Add refcounting fix for flow offload
Fix VLAN untagging issue on MT7986

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2022-11-21 11:47:36 +01:00
Maxim Anisimov
21762e4653 ramips: add support for Keenetic KN-3010
Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT.

Specification:
- System-On-Chip: MT7621DAT
- CPU/Speed: 880 MHz
- Flash-Chip: Winbond w25q256
- Flash size: 32768 KiB
- RAM: 128 MiB
- 5x 10/100/1000 Mbps Ethernet
- 4x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn
- Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac
- 4x LED, 2x button, 1x mode switch

Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
  wifi indicator.

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin"
   to "KN-3010_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
2022-11-20 16:44:24 +01:00
Xiaopo Zhang
a28297d395 x86: enable PINCTRL for all Intel platform
Enable Intel PINCTRL for all platform on both 32 bit and 64 bit target.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Xiaopo Zhang
34615250a9 x86/64: enable Intel PINCTRL in 64bit target
Intel PINCTRL is not enable in the 64bit build, while it is enabled in
the x86/general target, which disables the ability of controlling GPIO
in the 64 bit build.

This commit copies the corresponding part of x86/general config, since
it is already there, so it should be fine to enable the same settings
here.

Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
2022-11-20 16:31:10 +01:00
Will Moss
288b0004bf ath79: fix MAC address assigment for TP-Link TL-WR740N/TL-WR741ND v4
On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main
device MAC address, so do not increment it. WAN MAC is LAN MAC + 1.

Signed-off-by: Will Moss <willormos@gmail.com>
2022-11-20 16:30:27 +01:00
Roger Pueyo Centelles
5a1d7d8c1b ath79: disable image building for Ubiquiti EdgeSwitch 8XP
The downstream OpenWrt driver for the BCM53128 switch ceased to work,
rendering the 8 LAN ports of the device unusable. This commit disables
image building while the problem is being solved.

See issue #10374 for more details.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2022-11-20 16:24:24 +01:00
Edward Chow
3d343ca713 ath79: calibrate nand netgear wndrxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my wndr3700v4 and wndr4500v3.
Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-20 16:13:48 +01:00
Aleksander Jan Bajkowski
bca663f20f kernel: backport tso for asix driver
Performance comparison (iperf3, mtu 1500):
Before: 53.9 Mbps
After: 87.9 Mbps

The tests were performed on a BT Home Hub 5A router.
The iperf3 server was running on the router, the client
on the host.

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Christian Buschau
084c20f6c5 lantiq: xway: kernel: enable SMP support
Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT.

Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421.

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
d3527bb83b lantiq: xway: ar9: add ICU1 (2nd core for SMP)
Fixes leftover TODO from commit 6bf179b270

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Christian Buschau
fb0256e88e lantiq: xway: refresh kernel config
Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget'

Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2022-11-18 20:27:52 +01:00
Edward Chow
e354b01baf ath79: calibrate all ar9344 tl-WDRxxxx with nvmem
Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration
data from the nvmem subsystem.

This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.

wmac's nodes are also changed over to use nvmem-cells over OpenWrt's
custom mtd-cal-data property.

The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.

Test passed on my tplink tl-wdr4310.

Signed-off-by: Edward Chow <equu@openmail.cc>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
224babfd6f mediatek: mt7623: disable swconfig
The mt7623 subtarget supports 2 devices:
 * Bananapi BPi-R2 (added in 1f068588ef, 7762c07c88),
 * UniElec U7623-02 (added in 4def81f30f).

Both devices support DSA from the beginning, thus
swconfig can be safely disabled.

In the past, the subtarget mt7623 also supported
the mt7623 reference board. This board originally
supported swconfig, and was later converted to DSA
(64175ffb79) and then dropped (1ab81bf02d).

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Aleksander Jan Bajkowski
0e001e4185 mediatek: mt7623: refresh config
This was done by executing these command:
$ time make kernel_oldconfig CONFIG_TARGET=subtarget

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-11-18 20:27:52 +01:00
Moritz Warning
dc7d431b60 treewide: uniform vendor name for devolo
The company name is lower case on the website
(https://www.devolo.de) and in product names.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-18 20:27:52 +01:00
Moritz Warning
c0fb12c42e treewide: uniform vendor name for ASUS
Their own website (https://www.asus.com)
always uses the upper case style name.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-11-16 23:30:11 +01:00
Josef Schlehofer
941132cb3c mpc85xx: fix missing kernel config symbol
While compiling OpenWrt master for Turris 1.x routers (p2020), it
reported following error:

    Gianfar Ethernet (GIANFAR) [Y/n/m/?] y
    Freescale DPAA2 Ethernet Switch (FSL_DPAA2_SWITCH) [N/m/y/?] (NEW)
Error in reading or end of file.

Let's fix it by disabling it.

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2022-11-16 23:30:11 +01:00
John Audia
9e137bb10e kernel: bump 5.10 to 5.10.155
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-16 23:30:11 +01:00
John Audia
170f3d7b0a kernel: bump 5.15 to 5.15.79
All other patches automatically rebased

Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/mt7621
Run-tested: bcm2711/RPi4B, ramips/mt7621

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-16 23:30:11 +01:00
Kuan-Yi Li
49bbfd9968 cypress-nvram: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
c6e86d8095 linux-firmware: broadcom: consolidate NVRAM packages
NVRAM packages for the same wireless chip are consolidated into one as
they contain only small text files and symlinks.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-16 20:14:13 +01:00
Kuan-Yi Li
22fd8b0df6 cypress-nvram: disassociate from external source repo
Since all NVRAM files in external repo are now upstreamed and to lower
future maintenance cost, disassociate the package from external source
repo.

All upstream pending NVRAM files shall be stored locally from now on.

Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
[Remove outdated URL, add SPDX-License-Identifier]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2022-11-16 20:14:13 +01:00
Pawel Dembicki
f74275c936 kernel: add missing symbol in generic config
Found during work on qoriq target.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[improve commit message, remove from target configs]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-11-16 20:23:34 +02:00
Kuan-Yi Li
a110418027 linux-firmware: offer two versions of firmware for CYW4339
According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works
only with firmware from `linux-firmware`. However, firmware from
`cypress-firmware` suite is directly from the chip company (Infineon) and
is actually newer.

Instead of dropping the firmware from Infineon, create a package named
`brcmfmac-firmware-4339-sdio`, and keep the Infineon version of
`cypress-firmware-4339-sdio` around.

This gives us devs the option to choose. Also, it means that

 - packages `brcmfmac-firmware-*` uniformly come from `linux-firmware`
 - packages `cypress-firmware-*` uniformly come from `cypress-firmware`

so hopefully brings more clarity.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
2022-11-15 20:49:58 +01:00