In [0] support for ARC specific binutils were added, which was later removed
again [Fixes:].
Upstream binutils never had an extlib.
[0] 8b5d644b "toolchain: add support of ARC architecture"
Fixes: 8568dcd9 "toolchain: Remove binutils 2.29 for ARC targets"
Signed-off-by: Andre Heider <a.heider@gmail.com>
This patch fixes a corner case when using passwords that are exactly 64
characters in length with mesh mode or passwords longer than 63 characters
with SAE because 'psk' is used instead of 'sae_password'.
SAE is obligatory for 802.11s (mesh point).
The 'psk' option for hostapd is suited for WPA2 and enforces length
restrictions on passwords. Values of 64 characters are treated as PMKs.
With SAE, PMKs are always generated during the handshake and there are no
length restrictions.
The 'sae_password' option is more suited for SAE and should be used
instead.
Before this patch, the 'sae_password' option is only used with mesh mode
passwords that are not 64 characters long.
As a consequence:
- mesh passwords can't be 64 characters in length
- SAE only works with passwords with lengths >8 and <=63 (due to psk
limitation).
Fix this by always using 'sae_password' with SAE/mesh and applying the PMK
differentiation only when PSK is used.
Fixes: #11324
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
[ improve commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Wiflyer WF3526-P and Zbtlink ZBT-WE1326 have the same circuit design.
Installing the misunderstading firmware of ZBT-WE3526 will cause Wi-Fi
not work due to allocate the wrong pcie port. Add alternative name to
help users easily build or download the correct firmware.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
MT7621 gets a new PCIe driver in the 5.15+ kernel. Allocating wrong PCIe
port will cause the PCIe NIC to not work properly. This commit fixes
the wrong port numbers on Zbtlink ZBT-WE1326.
According to the bootlog, MT7612E (5 GHz) is connected to pcie1, and
MT7603E (2 GHz) is connected to pcie2:
[4.197658] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[4.204609] mt7621-pci 1e140000.pcie: PCIE1 enabled
[4.209476] mt7621-pci 1e140000.pcie: PCIE2 enabled
...
[4.307988] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000
[4.367206] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
On some devices the chip has RTC but no battery save time.
This leads back to getting the wrong time
and skipping the check of the last file modification date.
This commit ensures that the file time is checked even
if the RTC exists.
which would ordinarily return an approbiate
system time used for e.g. certificate generation.
Tested-on: NanoPi R2S
Signed-off-by: Yuan Tao <ty@wevs.org>
The name of squashfs is confusing since in reality it's a really old
version using an old lzma library. This tools is used for old ath79
netgear target and to produde a fake squasfs3 image needed for some
specific bootloader from some OEM (AVM for example)
Rename squashfs tool to squasfs3-lzma to better describe it.
Rename the installed bin from mksquashfs-lzma to mksquashfs3-lzma.
Use tar transform to migrate the root directory in tar to the new
naming.
Drop redundant PKG_CAT variable not needed anymore.
Also update any user of this tool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Including kernel.mk moves the package build folder in the linux one, which
is confusing since this isn't building any kernel modules.
package-defaults.mk is already included my package.mk.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Chromium devices (like Google WiFi) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Chromium devices (like OnHub) have ramoops memory reserved by the
bootloader. Let's enable the ramoops kernel module by default, so we get
better crash logging.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pstore ramoops support is useful even when there isn't an explicit
panic/crash. We can log all kernel messages via a "console", and then
retrieve them in the event of some non-kernel-panic reset (e.g.,
watchdog).
Since the buffer memory is already reserved, there isn't much overhead
to doing this.
The new console files will show up as:
/sys/fs/pstore/console-ramoops-N
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
FCC ID: A8J-EPG600
Engenius EPG600 is an indoor wireless router with
1 Gb ethernet switch, dual-band wireless,
internal antenna plates, USB, and phone lines (not supported)
this board is a Senao device:
the hardware is equivalent to EnGenius ESR600 (except for phone lines)
the software is Senao SDK which is based on openwrt and uboot
which uses the legacy Senao header with Vendor / Product IDs
to verify the firmware upgrade image.
**Specification:**
- MT7620 SOC MIPS 24kec, 2.4 GHz WMAC, 2x2
- RT5592N WLAN PCI chip, 5 GHz, 2x2
- QCA8337N Gb SW RGMII GbE, SW P0 -- SOC P5, 5 LEDs
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 64 MB RAM NT5TU32M16
- UART console J2, populated
- USB 2.0 port direct to SOC
- 6 GPIO LEDs power, 2G, 5G, wps2g, wps5g, line
- 3 buttons reset, wps, "reg" (registeration)
- 4 antennas internal omni-directional plates
NOT YET SUPPORTED: VoIP
- Si3050-FT + Si3019-FT Voice DAA, SPI control, PCM data
- Phone Ports "TEL", "LINE" RJ11, 4P2C (2 pins)
**MAC addresses:**
MAC address labeled as MAC ADDRESS
MACs present in both wifi cal data and uboot environment
eth0.1/phy1 ---- *:82 rf 0x4
phy0 ---- *:83 factory 0x4
eth0.2 MAC *:b8 "wanaddr"
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.0.1
username and password 'admin'
Navigate to gear icon, "Device Management", "Tools"
select the factory.dlf image
Upload and verify checksum
Method 2: Serial to upload initramfs:
Follow directions for TFTP recovery
upload and boot initramfs and do a sysupgrade
**TFTP recovery:**
Requires UART serial console, reset button does nothing
rename initramfs-kernel.bin to 'uImageEPG600'
make available on TFTP server at 192.168.99.8
power board, interrupt boot with "4"
execute `tftpboot` and `bootm` (with the load address)
**Return to OEM:**
Images from OEM are provided, but not compatible
with openwrt sysupgrade. So it must be modified.
Alternatively, back up all mtd partitions before flashing
**Note on switch registers:**
The necessary registers needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by using the following lines in the switch driver ar8327.c
in the function 'ar8327_hw_config_of'
where 'qca,ar8327-initvals' is parsed from DTS
before the new register values are written:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
pr_info("0x08 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD5_MODE));
pr_info("0x0c %08x\n", ar8xxx_read(priv, AR8327_REG_PAD6_MODE));
pr_info("0x10 %08x\n", ar8xxx_read(priv, AR8327_REG_POWER_ON_STRAP));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
in order for the option ephy-disable to work
without also needing ephy-base option,
we have to skip all the lines that write to mdio addresses that
assume those addresses do not have an external switch.
Otherwise, ephy ports will be disabled in hardware,
but register writes still happen as if they are enabled.
Split the functions so that other things are done first,
and ephy port setup can be skipped with a simple "return".
Tested on Engenius EPG600 (MT7620A ver:2 eco:3)
with QCA8337 external switch
Ref: cc6fd6fbb5 ("ramips: mt7620: add ephy-disable option to switch driver")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Changes:
7f7a9f7 wireless-regdb: update regulatory database based on preceding changes
660a1ae wireless-regdb: Update regulatory info for Russia (RU) on 5GHz
fe05cc9 wireless-regdb: Update regulatory rules for Japan (JP) on 6GHz
d8584dc wireless-regdb: Update regulatory rules for Japan (JP) on 5GHz
c04fd9b wireless-regdb: update regulatory rules for Switzerland (CH)
f29772a wireless-regdb: Update regulatory rules for Brazil (BR)
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Zyxel NBG7815 supports bluetooth with blsp1_uart3.
Configuration are already added to dts file, device needs only module to working bluetooth properly.
Tested at below posts:
https://forum.openwrt.org/t/openwrt-support-for-armor-g5-nbg7815/98598/259?u=itork
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Karol Przybylski <karol.przybylski@esm-technology.pl>
Specifications:
* SoC: MediaTek MT7622BV
* RAM: DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
* Flash: SPI-NAND 256 MiB (Toshiba TC58CVG1S3HRAIJ)
* Wi-Fi 2.4/5 GHz 4T4R:
* 2.4 GHz: MediaTek MT7622BV
* 5 GHz: MediaTek MT7915AN/MT7975AN
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000/2500 Mbps WAN (Realtek RTL8221B PHY)
* Switch: MediaTek MT7531AE
* LEDs/Keys: 8/1 (Power, Internet, LAN1, LAN2, LAN3, LAN4,
Wifin and Wifia dual-colour LEDs + Reset pin)
* UART: Marked J19 on board VCC GND TX RX, beginning from "1". 3.3v,
115200n8
* Power: 12 VDC, 2.5 A
Installation:
* Flash the factory image through the stock web interface, or TFTP to
the bootloader. NMRP can be used to TFTP without opening the case.
* U-Boot allows booting an initramfs image via TFTP as follows:
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.100
tftpboot openwrt-mediatek-mt7622-netgear_wax206-initramfs-recovery.itb
bootm
Known Limitations:
* The 2.5G WAN port labeled 'wan' only works for speeds up to 1G at the
moment. If connected to a multi-gig port the speed has to be manually
set to 1G/full either for the switch port or in OpenWrt. For example
add the following to /etc/rc.local to set it on boot:
/usr/sbin/ethtool -s wan speed 1000 duplex full
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to WAX206 GPL source:
https://www.downloads.netgear.com/files/GPL/WAX206_V1.0.4.0_Source.rar
* openwrt/target/linux/mediatek/dts/mt7622-netgear-wax206.dts
DTS file for this device.
* openwrt/target/linux/mediatek/image/mt7622.mk
Image creation code for this device
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[fix WAN port (1G only), adjust partition layout, adjust image creation]
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Some devices like ZBT WE1326 and ZBT WF3526-P and some Netgear models need
to delay phy port initialization after calling the mt7621_pcie_init_port()
driver function to get into reliable boots for both warm and hard resets.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit fixes the following commit
f584fb2f7e kernel: import accepted MediaTek Ethernet patches
Unrefreshed patches caused the CI to fail.
Signed-off-by: Paul Spooren <mail@aparcar.org>
With 5.15 kernel version Linksys EAX500 family devices suffered from a
big regression where the Ethernet switch became silent and started to
malfunction.
It was discovered later that the cause was not really the kernel upgrade
itself but a hackish implementation of the hw implementation of these
special routers.
In the original Linksys source code, GPIO 63 was handled in a special way
and was reset on reboot.
Normally GPIO 63 is used for pcie2 reset but in every device we support,
pcie2 is actually never used as nothing is attached to it.
Linksys rerouted GPIO 63 to the switch reset pin and deviates from
common hw implementation.
Till now it was used an hack to handle this case... It was set pcie3 as
working (while actually nothing was connected), set it to output low
(for assert-deassert from the pcie init code) and be done with it.
The result was that the GPIO was reset for enough time in early boot and
everything worked correctly.
This hack implementation was born to fail from the very start and in
kernel 5.15 finally problem arised.
In 5.15 pcie code changed and now the GPIO reset pin is not asserted as
probe won't fail if nothing is connected to the line (the old behaviour)
This result in the switch hold the reset pin and the Ethernet switch
dead.
On top of that with 5.15 code got optimized and simply attaching the
GPIO reset to the mdio wasn't enough as the switch require at least 10ms
to be correctly reset.
So implement finally a correct solution where:
- pcie2 is correctly disabled (nothing attached, unused)
- drop the wrong output-low for pcie2 reset pin
- define GPIO 63 as switch reset
- Add the reset-gpios to the mdio0 node
- Set the reset-post-delay-us to 12ms to correctly give time the switch
to reset
Fixes: #10983
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
I tested kernel 5.15 on my device for several times without any problems.
In my tests, 5.15 kernel has performance improvements such MGLRU.
Finally, initial kernel 6.1 support is imminent. All ramips subtargets have
5.15 as testing kernel. So, it's time to change.
Tested on my Archer C6 v3.2 (mt7621)
Signed-off-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
[reformat commit subject and message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Wrong pcie port number for WLAN causes missing 5g WLAN interface with 5.15
kernel. This changes port from pcie0 to pcie1 in dtsi.
[1.166330] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK)
[1.180073] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[1.193889] mt7621-pci 1e140000.pcie: PCIE1 enabled
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
We currently have build options to customize the IP address used in the
preinit phase of the boot process, but not to set the default LAN IP.
Introduce a boolean build option that, when enabled, results in the IP
address configured for the preinit phase, to be also used as the default
LAN IP address.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
ipq807x does not compile-in hwmon core, and this is leading to the hwmon
code in AQR driver not being compiled due to IS_REACHABLE(CONFIG_HWMON)
evaluating to false as hwmon is being built as a module.
So, lets not compile-in Aquantia PHY driver so it can be included as kmod
instead to have functioning hwmon.
This allows using the thermal sensors in AQR-s as thermal zones for
cooling devices like fans.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package the Aquantia AQR PHY driver as kmod.
This enables using the Aquantia driver with hwmon support on targets where
hwmon is not compiled-in.
Currently, in case when AQR driver is compiled-in but hwmon core is not
hwmon code in AQR driver will not get compiled because of macro
IS_REACHABLE(CONFIG_HWMON) evaluating to false.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Package kmod-ipt-raw enables CONFIG_IP_NF_RAW and packages
iptable_raw.ko
According to kernel's net/netfilter/Kconfig there are only 3 kernel
symbols that depend on the IP_NF_RAW:
1. NETFILTER_XT_TARGET_CT (xt_CT.ko)
2. NETFILTER_XT_TARGET_NOTRACK (unused symbol?!)
3. NETFILTER_XT_TARGET_TRACE (xt_TRACE.ko)
Now: iptables-mod-conntrack-extra selects kmod-ipt-conntrack-extra which
provides: xt_helper.ko nf_conncount.ko xt_connlimit.ko xt_connmark.ko
xt_recent.ko and xt_connbytes.ko (none of them seems to require
iptable_raw.ko).
It seems there is no explicit reason for iptables-mod-conntrack-extra to
require kmod-ipt-raw (iptables_raw.ko).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Replace a standalone init.d script with a platform implementation as
supported by netifd. This avoids a race between netifd and target
specific setups.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Import some accepted and pending upstream patches for mtk_eth_soc,
replacing some semantically equivalent local patches and fixing issues
when operating the PCS in 1G SGMII mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Starting from Linux Kernel version 6.3 UBI devices will no longer be
considered virtual, but rather have an MTD device parent. Hence they
will no longer be listed under /sys/devices/virtual/ubi which is
used in multiple places in OpenWrt. Prepare for future kernels by
using /sys/class/ubi instead of /sys/devuces/virtual/ubi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
