Use ipcalc's return value to react to invalid range specifications.
By simply ignoring the range instead of aborting with an error code,
dnsmasq should still start when there's an error (best effort).
Aborting the config generation or working with invalid range specs leaves
dnsmasq crash-looping which is the right thing to do concerning that
particular interface but it also hinders DHCP service on other interfaces
and DNS on the router itself.
Signed-off-by: Leon M. George <leon@georgemail.eu>
There's hardly an shell logic in ipcalc.sh and a $* that would garble
parameter positions.
Move the awk invokation to the shebang.
A rename from "ipcalc.sh" to "ipcalc" is desirable but could prove tricky
with packages in other repositories depending on the filename.
Signed-off-by: Leon M. George <leon@georgemail.eu>
It's possible to move range boundaries in a way that the start address
lies behind the end address.
Detect this condition and exit with an error message.
Signed-off-by: Leon M. George <leon@georgemail.eu>
With this patch, ipcalc only calculates range boundaries if the
corresponding parameters are supplied.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Bumping max frame size has significantly affected network performance
and memory usage. It was done by upstream commit that first appeared in
the 5.7 release.
Allocating 512 (BGMAC_RX_RING_SLOTS) buffers, 10 k each, is clearly a
bad idea on 32 MiB devices. This commit fixes support for Linksys E1000
V2.1 which gives up after allocating ~346 such buffers running 5.15
kernel.
Ref: 230c9da963 ("bcm53xx: revert bgmac back to the old limited max frame size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Most of the time when booting kernel prints a warning from
mm/page_alloc.c when pstore/ramoops is being initialized and ramoops is
not functional.
Fix this by moving ramopps node into reserved-memory block as described
in kernel documentation.
Fixes: 2964e5024c ("ipq806x: kernel ramoops storage for C2600/AD7200")
Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Release information:
https://github.com/pkgconf/pkgconf/blob/master/NEWS
Fixes CVE-2023-24056.
Further, this commit corrects the "-Dtests" flag and changes it from
"false" to "disabled".
Signed-off-by: Nick Hainke <vincent@systemli.org>
In addition to version update, this commit applies a fixup to allow building
on MacOS involving renaming: [gt_TYPE_WINT_T] --> [gt_TYPE_WINT_T_GNUTLS]
suggested by zhanhb.
Build system: x86_64
Build-tested: bcm2711/RPi4B
Signed-off-by: John Audia <graysky@archlinux.us>
When fstools is unable to parse our root=<...> arg correctly, it can
fall back to scanning all block devices for a 'rootfs_data' partition.
This fallback was deemed wrong (or at least, a breaking/incompatible
change) for some targets, so we're forced to opt back into it with
fstools_partname_fallback_scan=1.
Without this, OnHub devices will use a rootfs-appended loop device for
rootfs_data instead of the intended 3rd partition.
While I'm at it, just move all the boot args into the 'cros-vboot'
build rule, instead of using the custom bootargs-append. All cros-vboot
subtargets here are using the same rootwait (to support both eMMC and
USB boot) and root/partition args.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[ drop unrelated comments in commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
There is no CONFIG_BINARY_DIR, it's CONFIG_BINARY_FOLDER.
While at it, don't parse the shell compatible .config, eval it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
If CONFIG_BINARY_FOLDER is set in .config, use that instead of "bin" as
the bindir.
That allows to set that config and easily run e.g.
`./scripts/qemustart armvirt 32`.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
$BOOTDEV_MAJOR may be empty for many of the uevents parsed in this
function. This condition thus tends to fail benignly (we just skip to
the next device), but it can really clutter the stage2 sysupgrade
stderr, since it looks like the "=" operand doesn't have an appropriate
left-hand argument.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Match interface numbers with printed numbers on device enclosure and
assign first port as WAN interface.
Notes
Serial console is available through RJ-45 port with Cisco pinout
baud: 19200, parity: none, flow control: none
The device is setup with UEFI. To enter setup hold DEL or ESC key on
boot. Default UEFI Administrator password is: bcndk1
For users using graphics IC it's advisable to disable display with:
i915.disable_display=1
appending to kernel command line inside bootloader, to save about
0.5-0.6W energy on idle.
For users not using graphics IC, disable it in UEFI, this will save about
1.5W energy on idle.
Pins marked CN19 are ATX power On/Off button.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
These devices have a partition table stored in flash, which compensates
for any pre-existing bad blocks by enlarging the respective partition.
This means that the current static partition table is only correct for
devices without any bad blocks.
Typical results of this mismatch are degraded wireless performance and
wrong MAC addresses, when the factory partition is shifted due to a bad
block somewhere before it. If there is a bad block already before the
ubi partition, then OpenWrt may not run at all because the kernel can't
find the rootfs.
Use the on-flash partition table to fix these issues. Replace the two
reserved partitions by the full partition list, as the driver does not
allow merging them.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The upstream value read from the device seems to already be in bits per
second, so there is no need to multiply by 1000 again (which for typical
values causes an overflow of the 32-bit unsigned integer).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Kconfig docs say:
> The default value deliberately defaults to 'n' in order to avoid
> bloating the build.
Apply this rule everywhere, to avoid more cloning of bad examples
Signed-off-by: Tony Butler <spudz76@gmail.com>
Inline the preinst.arm-ce script. Support for including was added in
make 4.2 and is not working with older make versions.
Fixes: https://github.com/openwrt/openwrt/issues/11866
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This commit adds support for the V4 hardware revision of the Deco M4R.
V4 is a complete overhaul of the hardware compared to V1 and V2,
and is much more similar to the Archer C6 V3 and C6U V1.
Specifications:
SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads)
RAM: Kingston D1216ECMDXGJD (256 MB)
Wireless 2.4 GHz: MediaTek MT7603EN
Wireless 5 GHz: MediaTek MT7613BEN
Flash: 16 MB SPI NOR
Installation:
Flash the *-factory.bin image in the U-Boot recovery webserver.
You can trigger this webserver by holding the reset button until the LED
flashes yellow, or by hooking up to serial pads on the board (clearly
labeled GND, RX and TX) and pressing `x` early in boot.
Once the factory image has been flashed, you can use the regular upgrade
procedure with sysupgrade images for subsequent flashes.
Signed-off-by: Mark Ceeha <hi@shiz.me>
Tested-by: Mark Ceeha <hi@shiz.me>
Adds support for building TP-Link Deco M4R v4 factory images
e7233d229c2c tplink-safeloader: Add support for Deco M4R V4
Signed-off-by: Mark Ceeha <hi@shiz.me>
This makes the patches and the kernel configuration apply on top of
kernel 5.15.
The following patch was removed because the old IDE subsystem was
removed from upstream kernel:
target/linux/bcm47xx/patches-5.15/610-pci_ide_fix.patch
This was tested successfully on a ASUS WL-500g Premium V1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
shellcheck warns against it with SC2086. It also hides a bug that
shellcheck marks with SC2015. Fixed those with explicit if/else.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Instead of using the shell's evaluation, use grep's -q parameter.
Found with shellcheck's SC2143.
Also replaced a head call with grep's -m.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Use openwrt official tools container by default.
Fork will use openwrt tools container by default.
This can be disabled by setting the option use_openwrt_container to
false for the build.yml and check-kernel-patches.yml.
The push-containers workflow is disabled on forks. The workflow can be
reenabled by commenting the condition in push-containers.yml.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable the CPU frequency scaling statistics in kernel config.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Use generic earlycon on Linux Kernel instead of initialization in platform
setup.
And also, drop bootargs with console= parameter from I-O DATA BSH-G24MB. It
uses 115200bps as baud-rate, the same as default in rtl838x.dtsi.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
