When the new variable ephy_base was introduced,
it was not applied to the if block for mdio_mode.
The first line in the mdio_mode if block
sets the EPHY base address to 12 in the SOC by writing a register,
but the corresponding variable in the driver
was still set to the default of 0.
This causes subsequent lines that write registers with the function
_mt7620_mii_write
to write to PHY addresses 0 through 4
while internal PHYs have been moved to addresses 12 through 16.
All of these lines are intended only for PHYs on the SOC internal switch,
however, they are being written to external ethernet switches
if they exist at those PHY addresses 0 through 4.
This causes some ethernet ports to be broken on boards with AR8327 or QCA8337 switch.
Other suggested fixes move those lines to the else block of mdio_mode,
but removing the else block completely also fixes it.
Therefore, move the lines to the mt7620_hw_init function main block,
and have only one instance of the function mtk_switch_w32
for writing the register with the EPHY base address.
In theory, this also allows for boards that have both external switches
and internal PHYs that lead to ethernet ports to be supported.
Fixes: 391df37829 ("ramips: mt7620: add EPHY base mdio address changing possibility")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit de5394a29d)
A workaround was added to the switch driver
to set SOC port 4 as an RGMII GMAC interface
based on the DTS property mediatek,port4-gmac.
(previously mediatek,port4)
However, the ethernet driver already does this,
but is being blocked by a return statement
whenever the phy-handle and fixed-link properties
are both missing from nodes that define the port properties.
Revert the workaround, so that both the switch driver
and ethernet driver are not doing the same thing
and move the phy-handle related lines down
so nothing is ending the function prematurely.
While at it, clean up kernel messages
and delete useless return statements.
Fixes: f6d81e2fa1 ("mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit afd60d650e)
These nodes are used for configuring a GMAC interface
and for defining external PHYs to be accessed with MDIO.
None of this is possible on MT7620N, only MT7620A,
so remove them from all MT7620N DTS.
When the mdio-bus node is missing, the driver returns -NODEV
which causes the internal switch to not initialize.
Replace that return so that everything works without the DTS node.
Also, an extra kernel message to indicate for all error conditions
that mdio-bus is disabled.
Fixes: d482356322 ("ramips: mt7620n: add mdio node and disable port4 by default")
Fixes: aa5014dd1a ("ramips: mt7620n: enable port 4 as EPHY by default")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit a2acdf9607)
There are only 2 options in the driver
for the function of mt7620 internal switch port 4:
EPHY mode (RJ-45, internal PHY)
GMAC mode (RGMII, external PHY)
Let the DTS property be boolean instead of string
where EPHY mode is the default.
Fix how the properties are written
for all DTS that use them,
and add missing nodes where applicable,
and remove useless nodes,
and minor DTS formatting.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 953bfe2eb3)
This enables autonegotiation for all ephy ports on probe.
Some devices do not configure the ports, particularly port 4.
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[replace magic values ; reword commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0056ffb468)
The basic mode control register of the ESW PHYs is modified in this
codeblock. Use the respective macros to make this code more readable.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 6a15abbc75)
About the device
----------------
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.
Installation
------------
Using the webcmd interface
--------------------------
Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.
You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.
1. Log into the device's admin portal. This is necessary to
authenticate you as a user in order to be able to access the
webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
the console directly through this page, or you may wish to
launch the installed `telnetd` and use telnet instead.
* Using telnet is recommended since it provides a more
convenient shell interface that the web form.
* Launch telnetd from the form with the command `telnetd`.
* Check the port that telnetd is running on using
`netstat -antp|grep telnetd`, it is likely to be 2323.
* Connect to the target using `telnet`. The username should
be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
* The flash partition should be mtd4, but check
/sys/class/mtd/mtd4/name first. The partition should be
called 'Kernel'.
* To flash use the following command:
`mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
Where mtd<n> is the Kernel partition, and <image-file> is
the OpenWrt image previously downloaded.
* The command above will erase, flash and then reboot the
device. Once it reboots it will be running OpenWrt.
Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.
Using the serial port
---------------------
The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.
Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.
Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
(cherry picked from commit a509b80065)
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600
Descriptions:
Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
really different, the only hardware difference between the two models is flash
size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
compatible with YK-L1's firmware but it's better to split it to different models.
It is easy to identify the models by looking at the label on the bottom of the
device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
to install compatible firmware, so please backup config file before system upgrade.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 4a9f389ed2)
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 882a6116d3)
Youku YK-L1 has a huge storage space up to 32 MB. It is better to
use a higher spi clock to read or write serial nor flash chips.
Youku YK-L1 has Winbond w25q256fvfg on board that can support
104 MHz spi clock so 48 MHz is safe enough.
The real frequency can only be sysclk(580MHz ) /3 /(2^n) so 80 MHz
defined in dts file will set only 48 MHz in spi bus.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit bf7ddb18f1)
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(cherry picked from commit 06af45ec05)
CONFIG_BLK_DEV_NVME [1]:
- This is a kernel driver for SSD connected to PCI or PCIe bus [1].
By default, it is enabled for targets "ipq807x", "rockchip/armv8"
and "x86/64".
With miniPCIe adapter, there is a possibility to connect NVMe disk
to Turris Omnia (cortex-a9), Turris MOX (cortex-a53).
It allows to boot system from NVMe disk, because of that it can not
be kmod package as you can not access the disk to be able to boot from
it.
CONFIG_NVME_CORE [2]:
- This is selected by CONFIG_BLK_DEV_NVME
It does not need to be explicitly enabled, but it is done for "ipq807",
"x64_64" and rockchip/armv8", which has also enabled the previous config
option as well.
Kernel increase: ~28k KiB on mamba kernel
Reference:
[1] https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[2] https://cateee.net/lkddb/web-lkddb/NVME_CORE.html
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 9d530ac4bf)
[rebased for config-5.4]
These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.
Note for users sysupgrading from the previous ath79-generic snapshot
images:
The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.
To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".
If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:
* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message facelift]
(cherry picked from commit 44e1e5d)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
According to the vendor [1] these HATs share the same DT overlay:
hifiberry-dacplus. The PCM512x-compatible control unit is attached to
I2C, so the additional snd-soc-pcm512x-i2c kernel module is required.
Also explicitly note the Amp2 support to reduce confusion for those
users.
[1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/>
Signed-off-by: Torsten Duwe <duwe@lst.de>
(added bcm27xx tag, changed commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7ea9936f7f)
The MikroTik RouterBOARD mAPL-2nd (sold as mAP Lite) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.
See https://mikrotik.com/product/RBmAPL-2nD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 1.5 dBi antenna
- Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 802.3af/at PoE in
- 4 user-controllable LEDs:
· 1x power (green)
· 1x user (green)
· 1x lan (green)
· 1x wlan (green)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Note: following 781d4bfb39
The network setup avoids using the integrated switch and connects the
single Ethernet port directly. This way, link speed (10/100 Mbps) is
properly reported by eth0.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit eb38af7881)
Specification:
- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry-picked from commit a05dcb0724)
[switch to mtd-mac-address instead of nvmem-cells]
Specification:
- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry-picked from commit c91df224f5)
Fixes two high-severity vulnerabilities:
- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
can be bypassed. If a malicious client does not send the
certificate_verify message a client can connect without presenting a
certificate even if the server requires one.
- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
v1.3 server can have its certificate heck bypassed. If the sig_algo in
the certificate_verify message is different than the certificate
message checking may be bypassed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit e89f3e85eb)
This updates mac80211 to version 5.10.110-1 which is based on kernel
5.10.110.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename feature variable clang-bpf-global-var following upstream changes.
This restores the HAVE_CLANG feature override and should avoid rare build
errors where a recent host clang and BTF-enabled host kernel are present.
Fixes: 23be333401 ("bpftools: update to 5.10.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit cf20f1bb5f)
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.
Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.
this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.
The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.
This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.
However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.
Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[pepe2k@gmail.com: backported to 21.02]
Fixes: #9655, #9636, #9547
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit 74516f4357)
When using external targets there is a symlink being created for the
target under target/linux which then becomes dangling under Image
Builder. Fix it by dereferencing the possible symlink.
Tested on IB with external target, ipq40xx and mvebu.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 621f39d1f4)
(cherry picked from commit ec9af870f3)
When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Same has been done for the Archer C7 before:
commit e19506f206 ("ath79: migrate Archer C7 5GHz radio device paths")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit c6eb63d48f)
The label has the MAC address of eth0, not the WLAN PHY address. We can
merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS
derived from it use the same interface for their label MAC addresses
after all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit aee9ccf5c1)
This backports the following upstream Linux patches
net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant
net: sfp: relax bitrate-derived mode check
net: sfp: cope with SFPs that set both LOS normal and LOS inverted
for 5.4 for mvebu platform.
This fixes GPON modules:
Ubiquiti U-Fiber Instant SFP GPON
VSOL V2801F
CarlitoxxPro CPGOS03-0490 v2.0
Signed-off-by: Marek Behún <marek.behun@nic.cz>
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
to be on the router with the previous naming
[ 6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[ 6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin
- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.
Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.
Fixes:
- FragAttacks
- Kr00k
Also add LICENSE file
Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.
Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-febaba43
After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (4ca95bb CY) FWID 01-996384e2
[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 7ca7e0b22d)
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.
Also change the ethernet config to reduce loss on sub-1G links.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4551bfd91f)
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 8ba71f1f6f)
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.
Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.
Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit b3aa2909a7)
(cherry picked from commit 3965dda0fa)
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ffa1088f63)
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase]
(cherry picked from commit a8b2d35903)
(cherry picked from commit b9e90935db)
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 80f21e5336)
(cherry picked from commit d65269a732)
The label has the MAC address of eth0, not the WLAN PHY address.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 2a02b70499)
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a1ac8728f8)
Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.
This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 6f78723977)
Include the current operation class to hostapd get_status interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2a31e9ca97)
Add the beacon interval to hostapd status output. This allows external
services to discover the beacon interval for a specific VAP.
This way, external wireless management daemons can correctly calculate
fields containing TBTT value from absolute time-values.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ba9846842)
Imports a function from iw to convert frequencies to channel numbers.
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
[fix potential out of bounds read]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 398df62756)
To allow steering daemons to be aware of the STA-decided transition
target, publish WNM transition responses to ubus. This way, steerings
daemons can learn about STA-chosen targets and send a better selection
of transition candidates.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a3de42e72c)
The existing wnm_disassoc_imminent ubus method only supports issuing a
bss transition request with the disassoc imminent flag set.
For use-cases, where the client is requested to roam to another BSS
without a pending disassoc, this existing method is not suitable.
Add a new bss_transition_request ubus method, which provides a more
universal way to dispatch a transition request. It takes the following
arguments:
Required:
addr: String - MAC-address of the STA to send the request to (colon-seperated)
Optional:
abridged - Bool - Indicates if the abridged flag is set
disassociation_imminent: Bool - Whether or not the disassoc_imminent
flag is set
disassociation_timer: I32 - number of TBTTs after which the client will
be disassociated
validity_period: I32 - number of TBTTs after which the beacon
candidate list (if included) will be invalid
neighbors: blob-array - Array of strings containing neighbor reports as
hex-string
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0eed96ca5d)
This is a bugfix release. Changelog:
*) Fixed a bug in the BN_mod_sqrt() function that can cause it to loop
forever for non-prime moduli. (CVE-2022-0778)
*) Add ciphersuites based on DHE_PSK (RFC 4279) and ECDHE_PSK
(RFC 5489) to the list of ciphersuites providing Perfect Forward
Secrecy as required by SECLEVEL >= 3.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit e17c6ee627)
This fixes:
bash: xxd: command not found
on hosts without xxd installed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 9dbca6bf6e)
Fixes: 45b3f2aa0f ("uboot-bcm4908: add package with BCM4908 U-Boot")
Don't download all of vim just to build xxd. Use a tight tarball
containing only xxd sources instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b94aac7a1)
