Changes between 1.1.1p and 1.1.1q [5 Jul 2022]
*) AES OCB mode for 32-bit x86 platforms using the AES-NI assembly optimised
implementation would not encrypt the entirety of the data under some
circumstances. This could reveal sixteen bytes of data that was
preexisting in the memory that wasn't written. In the special case of
"in place" encryption, sixteen bytes of the plaintext would be revealed.
Since OpenSSL does not support OCB based cipher suites for TLS and DTLS,
they are both unaffected.
(CVE-2022-2097)
[Alex Chernyakhovsky, David Benjamin, Alejandro Sedeño]
Signed-off-by: Dustin Lundquist <dustin@null-ptr.net>
(cherry picked from commit 3899f68b54)
The MediaTek's Crypto Engine driver has been replaced with the upstream
Inside Secure's SafeXcel cryptographic engine driver, however kconfig
has not been changed accordingly, this commit fixes it.
Fixes: 127ad76 ("mediatek: switch over to extended upstream eip97
driver")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 3f2d0703b6)
Release notes:
https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.4.3-relnotes.txt
```
It includes the following security fix:
* A malicious certificate can cause an infinite loop.
Reported by and fix from Tavis Ormandy and David Benjamin, Google.
(CVE-2022–0778)
```
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 25534d5cc2)
Changes between 1.1.1o and 1.1.1p [21 Jun 2022]
*) In addition to the c_rehash shell command injection identified in
CVE-2022-1292, further bugs where the c_rehash script does not
properly sanitise shell metacharacters to prevent command injection have been
fixed.
When the CVE-2022-1292 was fixed it was not discovered that there
are other places in the script where the file names of certificates
being hashed were possibly passed to a command executed through the shell.
This script is distributed by some operating systems in a manner where
it is automatically executed. On such operating systems, an attacker
could execute arbitrary commands with the privileges of the script.
Use of the c_rehash script is considered obsolete and should be replaced
by the OpenSSL rehash command line tool.
(CVE-2022-2068)
[Daniel Fiala, Tomáš Mráz]
*) When OpenSSL TLS client is connecting without any supported elliptic
curves and TLS-1.3 protocol is disabled the connection will no longer fail
if a ciphersuite that does not use a key exchange based on elliptic
curves can be negotiated.
[Tomáš Mráz]
Signed-off-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit eb7d2abbf0)
This improves NAT masquarade network performance.
An alternative to kernel change would be runtime setup but that requires
ethtool and identifying relevant network interface and all related
switch ports interfaces.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 82d0dd8f8a)
1. KCFLAGS should be used for custom flags
2. Optimization flags are arch / SoC specific
3. -fno-reorder-blocks may *worsen* network performace on some SoCs
4. Usage of flags was *reversed* since 5.4 and noone reported that
If we really need custom flags then CONFIG_KERNEL_CFLAGS should get
default value adjusted properly (per target).
Ref: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Link: http://lists.openwrt.org/pipermail/openwrt-devel/2022-June/038853.html
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20190409093046.13401-1-zajec5@gmail.com/
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 22168ae681)
This uses kernel's generic variable and doesn't require patching it with
a custom Makefile change. It's expected *not* to change any behaviour.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 1d42af720c)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 24e27bec9a)
The empty executable is causing problems with meson builds, due to the
error: OSError: [Errno 8] Exec format error: 'ldconfig'
This patch changes the empty ldconfig stub to symlink to /bin/true to
work around this issue.
Fixes: FS#4117
Fixes: 3bd31cc4d2 ("tools/meson: update to 0.60.0")
Signed-off-by: Damien Mascord <tusker@tusker.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # Tested on Debian 11
Tested-By: Lucian Cristian <lucian.cristian@gmail.com>
Tested-By: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 6a5b4228e3)
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
[backport to fix prereq check when moving from 22.03 branch to 21.02]
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Fixes: be0639063a ("kernel: bump 5.4 to 5.4.203")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch was backported to kernel 5.4.200, but without the wireguard
change, because wireguard is not available in upstream kernel 5.4.
This adds the missing changes for wireguard too.
Fixes: be0639063a ("kernel: bump 5.4 to 5.4.203")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since kernel 5.5-rc1 [1], there are upstreamed DTS files related to ESPRESSObin
variants. Move these to files-5.4.
This helps if you want to use a newer kernel version than used
in OpenWrt 21.02 (= LTS kernel 5.4), you would end up with duplicate files
(one outdated, one up to date from newer Linux versions).
Fixes:
Error: arch/arm64/boot/dts/marvell/armada-3720-espressobin-v7.dts:19.1-7:
Label or path ports not found
FATAL ERROR: Syntax error parsing input tree
[1] 447b878935
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 7be8ab4f7b)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
[reword commit subject and commit description]
Flow offload dst can become invalid after the route cache is created.
dst_check() in packet path is necessary to prevent packet drop.
Signed-off-by: Ritaro Takenaka <ritarot634@gmail.com>
This release comes with a security fix related to c_rehash. OpenWrt
does not ship or use it, so it was not affected by the bug.
There is a fix for a possible crash in ERR_load_strings() when
configured with no-err, which OpenWrt does by default.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 7a5ddc0d06)
Major changes are:
4 cleanups & typos fixes.
Add keep_last_dots mount option to allow access to paths
with trailing dots.
Avoid repetitive volume dirty bit set/clear to improve
storage life time.
Fix ->i_blocks truncation issue caused by wrong 32bit mask.
Fix ->i_blocks truncation issue that still exists elsewhere.
Fix missing REQ_SYNC in exfat_update_bhs().
Fix referencing wrong parent directory information during rename.
Fix slab-out-bounds in exat_clear_bitmap() reported from syzbot.
Improve performance while zeroing a cluster with dirsync mount option.
Introduce a sys_tz mount option to use system timezone.
Move super block magic number to magic.h
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of other devices from 'ramips' target.
Fixes: #9842Fixes: #8964
Reported-by: Juergen Hench <jurgen.hench@gmail.com>
Tested-by: Juergen Hench <jurgen.hench@gmail.com>
Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit fd72e595c2)
Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the
WPS cutton to fix button behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 535b0c70b1)
Remove restrictions on source and destination addresses, which aren't
specified on RFC8415, and for some reason in openwrt are configured
to allow both link-local and ULA addresses.
As cleared out in issue #5066 there are some ISPs that use Gloabal
Unicast addresses, so fix this rule to allow them.
Fixes: #5066
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
[rebase onto firewall3, clarify subject, bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 65258f5d60)
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Signed-off-by: Alban Bedel <albeu@free.fr>
(cherry picked from commit f953a1a4bf)
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.
Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617
- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072
Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit ab7e53e5cc)
[Deleted 5.10 from commit title]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Notify external ubus subscribers of received link-measurement reports.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f6445cfa1a)
Add a ubus method to request link-measurements from connected STAs.
In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 965aa33a18)
Allow external processes to enable advertisement of link-measurement RRM
capability.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2ca5c3da04)
aa0e3c4bbe12 iwinfo: nl80211: add support for printing the device path for a phy
dd6d6d2dec35 iwinfo: nl80211: use new path lookup function for nl80211_phy_idx_from_uci_path
268bb26d2e2a iwinfo: nl80211: support looking up phy by path=.. and macaddr=...
c0414642fead iwinfo: nl80211: fix typo
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(backported from commit 6e8475bbd0)
This is trivial fix of a duplicate definition of 'int ret'.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit df622768da)
MPLS feature symbols are normally only set when kmod-mpls is enabled, but the
CONFIG_MPLS symbol they depend on could also have been selected by openvswitch
instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 92add80414)
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.
Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)
When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.
So disable the internal switch VLANs by default on these boards.
Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.
In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 2adeada045)
Define and use some missing macros,
and use them instead of BIT() or numbers for more readable code.
Add comment for a bit change that seems unrelated to ethernet
but is actually needed (PCIe Root Complex mode).
Remove unknown and unused macro RST_CTRL_MCM
(probably from MT7621 / MT7622)
This is the last of a series of fixes, so bump version.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 88a0cebadf)
the register bits for TX delay and RX delay are opposites:
when TX delay bit is set, delay is enabled
when RX delay bit is set, delay is disabled
So, when both bits are unset, it is RX delay
and when both bits are set, it is TX delay
Note: TXID is the default RGMII mode of the SOC
Fixes: 5410a8e295 ("ramips: mt7620: add rgmii delays support")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 26c84b2e46)
Add back the register write to disable internal PHYs
as a separate option in the code that can be set using a DTS property.
Set the option to true by default
when an external mt7530 switch is identified.
This makes the driver more in sync with original SDK code
while keeping the lines separated into different options
to accommodate any board with any PHY layout.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit cc6fd6fbb5)
The function mt7620_mdio_mode is only called once
and both the function and mdio_mode block have been named incorrectly,
leading to confusion and useless commits.
These lines in the mdio_mode block of mt7620_hw_init
are only intended for boards with an external mt7530 switch.
(see commit 194ca6127e)
Therefore, move lines from mdio_mode to the place in soc_mt7620.c
where the type of mt7530 switch is identified,
and move lines from mt7620_mdio_mode to a main function.
mt7620_mdio_mode was called from mt7620_gsw_init
where the priv struct is available,
so the lines must stay in mt7620_gsw_init function.
In order to keep things as simple as possible,
keep the DTS property related function calls together,
by moving them from mt7620_gsw_probe to init.
Remove the now useless DTS properties and extra phy nodes.
Fixes: 5a6229a93d ("ramips: remove superfluous & confusing DT binding")
Fixes: b85fe43ec8 ("ramips: mt7620: add force use of mdio-mode")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 6972e498d3)
Set the PHY base address to 12 for mt7530 and 8 for others,
which is based on the default setting for some devices
from printing the register with the following command
after it is written to by uboot during the boot cycle.
`md 0x10117014 1`
PHY_BASE option only uses 5 bits of the register,
bits 16 to 20, so use 8-bit integer type.
Set the option using the DTS property mediatek,ephy-base
and create the gsw node if missing.
Also, added a kernel message to display the EPHY base address.
Note:
If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf)
then there is adverse effects with Atheros switches.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
(cherry picked from commit 0976b6c426)
