Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1
Installation
============
Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.
Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.
yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.
You can see three holes
From Bottom: RX, TX, Ground - partially covered
Download & Boot the OpenWrt initramfs image.
In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000
In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:
Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
================
2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected
The cover yellow light is not supported. (only blue one)
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
Add a struct_group to around all members in struct ath_cycle_counters.
It can help the compiler detect the intended bounds of the memcpy() and
memset().
This patch fixes the following build warning:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at /home/db/openwrt/build_dir/target-mips_24kc_musl/linux-ath79_generic/backports-6.1.24/drivers/net/wireless/ath/ath9k/main.c:140:3:
./include/linux/fortify-string.h:314:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
314 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Internet Initiative Japan Inc. (IIJ) SA-W2 is a network appliance with
11ac (Wi-Fi 5) wlan, based on 88F6810.
Specification:
- SoC : Marvell Armada 380 88F6810
- RAM : DDR3 256 MiB (Micron MT41K64M16TW-107:J x2)
- Flash : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- WLAN : 2.4/5 GHz, Mini PCI-E
- 2.4 GHz : Silex SX-PCEGN (Atheros AR9287 (2T2R))
- 5 GHz : Silex SX-PCEAC (Qualcomm Atheros QCA9880 (3T3R))
- Ethernet : 10/100/1000 Mbps x5
- Switch : Marvell 88E6172
- LEDs/Keys : 12x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C)
- settings : 115200n8
- assignment: 1:NC, 2:NC, 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC, 8:NC
- note : compatible with Cisco console cable
- Power : DC Input or PoE
- DC Input : 12 VDC, 3 A
- PoE : 802.3af
- module : Silvertel Ag9712-2BR
- note : USB ports shouldn't be used when powered by PoE
- Bootloader : PMON2000 based
- Stock : NetBSD based
Flash instruction using sysupgrade image:
1. Prepare TFTP server with IP address 192.168.0.10 and put sysupgrade
image to TFTP directory
2. Connect PC to "GE0/PoE" port on SA-W2
3. Power on SA-W2, interrupt count-down by Esc and enter to bootloader
CLI
4. Set IP address of the device
address 192.168.0.1
5. Download sysupgrade image and flash to storage
tftpload 192.168.0.10 <image name>
firmwrite
example:
#tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
Loading openwrt-mvebu-cortexa9-iij_sa-w2-squashfs-sysupgrade.bin
loaded 8127268 byte(s)
#firmwrite
Erasing FLASH block 32 Done 0x00200000.
Erasing FLASH block 33 Done 0x00210000.
...
Erasing FLASH block 155 Done 0x009b0000.
Erasing FLASH block 156 Done 0x009c0000.
Programming FLASH. Done.
Verifying FLASH. No Errors found.
6. Check the flashed firmware
firmcheck
example:
#firmcheck
[Normal firmware]
ident: 'SEIL2015'
copyright: 'ARM OpenWrt Linux-5.15.93'
version format: 1
version major: 9
version minor: 99
version release: 'r22060+36-5163bb5e54'
body size: 3578524
checksum: 0x8a083cb8
[Rescue firmware]
ident: 'SEIL2015'
copyright: 'Copyright (c) 2017 Internet Initiative Japan Inc. All rights reserved.'
version format: 1
version major: 3
version minor: 70
version release: 'Release'
body size: 10152458
checksum: 0x8f9518c2
7. Boot with the flashed firmware
boot
Note:
- The bootloader on this device is not U-Boot and it's environment space
("bootloader-env") has no compatibility with U-Boot tools.
- eth1 is connected to port6 of 88E6172 switch, but multi-cpu port can't
be handled on Linux Kernel and not defined.
- Powering by PoE hasn't been tested yet.
- This device has 2x OS images on flash and they can be switched by
setting "BOOTDEV" variable on bootloader CLI.
That variable supports the following values:
- "flash" : primary image on flash ("firmware")
- "rescue": secondary image on flash ("rescue")
- "usb" : usb storage (broken?)
- "lan0/1": network
command to set:
set BOOTDEV=<dev>
example:
set BOOTDEV=rescue
This commit also supports booting from secondary partition.
- To execute initramfs image on bootloader CLI, use "go" command.
("go" command is not listed on the output of "help", but available)
example (download and execute):
address 192.168.0.1
tftpload 192.168.0.10 openwrt-mvebu-cortexa9-iij_sa-w2-initramfs-kernel.bin
go
MAC addresses:
LAN : 00:E0:4D:xx:xx:19 (none)
WAN : 00:E0:4D:xx:xx:18 (board_info, 0x6 (hex))
2.4 GHz: 84:25:3F:xx:xx:xx (Mini PCI-E card)
5 GHz : 84:25:3F:xx:xx:xx (Mini PCI-E card)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This mtdsplit parser driver parses firmware partition on Internet
Initiative Japan Inc. (IIJ) SEIL series devices.
Structure of header:
0x0 - 0x7 : Identifier (hex)
0x8 - 0x57: Copyright (ascii)
0x58 - 0x5b: Data CRC (hex)
0x5c - 0x5f: Image Format Version (hex)
0x60 - 0x63: Image Major Version (hex)
0x64 - 0x67: Image Minor Version (hex)
0x68 - 0x87: Image Release Version (ascii)
0x88 - 0x8b: Xor value for Data? (hex)
0x8c - 0x8f: Data Length (hex)
Properties:
- compatible : "iij,seil-firmware"
- iij,seil-id : ID of SEIL firmware for the device (8 bytes)
- examples:
- SA-W2 : <0x5345494c 0x32303135> ("SEIL2015")
- SEIL/X1 : <0x5345494c 0x2F582020> ("SEIL/X ")
- iij,bootdev-name: boot device name assigned to the partition
(optional)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Specifications:
SoC: QCA9531(650MHz)
RAM: DDR2 128M
Flash: SPI NOR 16M + SPI NAND 128M
WiFi: 2.4GHz with 2 antennas(WiFi/Thread)
Ethernet:
1xLAN(10/100M)
2xWAN(10/100M)
Button: 1x Reset Button
Switch: 1x Mode switch
LED: 1x Blue LED + 1x White LED + 1x Orange LED
IOT: Thread + ZigBee/Zwave
By uboot web failsafe:
Push the reset button for 5 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
This adds a configuration for github codespace using our buildbot
container. This allows users to start VS code in the browser using the
buildbot build container.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Due to circuit issue or silicon defect, sometimes the WiFi switch button
of the Archer C7 v2 can be accidentally triggered multiple times in one
second. This will cause WiFi to be unexpectedly shut down and trigger
'irq 23: nobody cared'[1] warning. Increasing the key debounce interval
to 1000 ms can fix this issue. This patch also add the missing rfkill
key label.
[1] Warning Log:
```
[87765.218511] irq 23: nobody cared (try booting with the "irqpoll" option)
[87765.225331] CPU: 0 PID: 317 Comm: irq/23-keys Not tainted 5.15.118 #0
...
[87765.486246] handlers:
[87765.488543] [<85257547>] 0x800c29a0 threaded [<5c6328a2>] 0x80ffe0b8 [gpio_button_hotplug@4cf73d00+0x1a00]
[87765.498364] Disabling IRQ #23
```
Fixes: https://github.com/openwrt/openwrt/issues/13010
Fixes: https://github.com/openwrt/openwrt/issues/12167
Fixes: https://github.com/openwrt/openwrt/issues/11191
Fixes: https://github.com/openwrt/openwrt/issues/7835
Tested-by: Hans Hasert
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
HiWiFi HC5861 has a GbE port which connected to the RTL8211E PHY
chip. This patch adds the missing Realtek PHY driver package and
sets the correct external PHYs base address to make it work again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xc22): relocation R_MIPS16_26 against `libxt_DNAT_init' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol printf
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xcc8): relocation R_MIPS16_26 against `luaL_argerror' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x4194): relocation R_MIPS16_26 against `cil_printf.lto_priv.0' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol memcmp
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled:
<artificial>:(.text.exit+0x6e): relocation R_MIPS16_26 against `pthread_key_delete' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol stpcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x400c): relocation R_MIPS16_26 against `iwinfo_close' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
Currently the zram default compressor choice is displayed whether or not
zram is activated. Since the default choice is lzo-rle, this adds a
false dependency on kmod-lib-lzo.
With this patch, the choice options appear only when activating zram.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
a170683 firmware-utils: fix use of NULL string progname
89875fc tplink-safeloader: CPE510: add Canadian support
9e211d2 mktplinkfw2: add support to extract bootloader images
c18f662 mktplinkfw2: add support to pack bootloader
3dc1339 mktplinkfw2: show exact exceed bytes when the image is to big
d16ff79 tplink-safeloader: WPA8631: add v4 AU, US
0fa1cc5 zytrx: add LTE5398-M904
6354661 firmware-utils: ptgen: add SiFive GPT partition support
The removed patch was applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes it possible to build the ipq807x netgear-wax218 without initramfs - which is required for downstream projects (gluon)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Designated initializers are required when using the randstruct GCC
plugin, otherwise an error like the following is seen:
./include/linux/lzma.h:60:31: error: positional initialization of field in 'struct' declared with 'designated_init' attribute [-Werror=designated-init]
This was originally applied via 55643e469c, but was unintentionally
reverted in 483503603c.
Fixes: 483503603c ("generic: 5.15: rework pending patch")
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Fortinet FortiGate 30E (FG-30E) is a UTM, based on Armada 385 (88F6820).
Specification:
- SoC : Marvell Armada 385 88F6820
- RAM : DDR3 1 GiB (4x Micron MT41K256M8DA-125, "D9PSH")
- Flash : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet : 5x 10/100/1000 Mbps
- Switch : Marvell 88E6176
- LEDs/Keys : 16x/1x
- UART : "CONSOLE" port (RJ-45, RS-232C level)
- port : ttyS0
- settings : 9600bps 8n1
- assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
5:GND, 6:RXD, 7:NC , 8:NC
- note : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power : 12 VDC, 2 A
- plug : Modex 5557-02R
Flash instruction using initramfs image:
1. Power on FG-30E and interrupt to show bootmenu
2. Call "[I]: System information." -> "[S]: Set serial port baudrate."
and set baudrate to 9600 bps
3. Call "[R]: Review TFTP parameters.", check TFTP parameters and
connect computer to "Image download port" in the parameters
4. Prepare TFTP server with the parameters obtained above
5. Rename OpenWrt initramfs image to "image.out" and put to TFTP
directory
6. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
image from TFTP server
7. Type "r" key when the following message is showed, to boot initramfs
image without flashing to spi-nor flash
"Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"
8. On initramfs image, backup mtd if needed
minimum:
- "firmware-info"
- "kernel"
- "rootfs"
9. On initramfs image, upload sysupgrade image to the device and perform
sysupgrade
10. Wait ~200 seconds to complete flashing and rebooting.
If the device is booted with stock firmware, login to bootmenu and
call "[B]: Boot with backup firmware and set as default." to set the
first OS image as default and boot it.
Notes:
- Both colors of Bi-color LEDs on the front panel cannot be turned on at
the same time.
- "PWR" and "Logo" LEDs are connected to power source directly.
- The following partitions are added for OpenWrt.
These partitions are contained in "uboot" partition (0x0-0x1fffff) on
stock firmware.
- "firmware-info"
- "dtb"
- "u-boot-env"
- "board-info"
Image header for bootmenu tftp:
0x0 - 0xf : ?
0x10 - 0x2f : Image Name
0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?
*: required for initramfs image
MAC addresses:
(eth0): 70:4C:A5:xx:xx:CE (board-info, 0xd880 (hex))
WAN : 70:4C:A5:xx:xx:CF
LAN 1 : 70:4C:A5:xx:xx:D0
LAN 2 : 70:4C:A5:xx:xx:D1
LAN 3 : 70:4C:A5:xx:xx:D2
LAN 4 : 70:4C:A5:xx:xx:D3
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Fix the building issue setting CC to KERNEL_CC in kernel.mk. The
kernel backports by default uses CC to compile kconf. A new patch is
added to mac80211 to compile kconf with host gcc.
Signed-off-by: Zeyu Dong <dzy201415@gmail.com>
[ refresh patches ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Kernel module packages compiling is not cached (e.g. mac80211)
even with CONFIG_CCACHE on.
CC should be set to KERNEL_CC in KERNEL_MAKE_FLAGS at kernel.mk
to allow kernel module packages using ccache.
Signed-off-by: Zeyu Dong <dzy201415@gmail.com>
d8118f6 config: make sure timer is not on the timeouts list before freeing
4bbc6e7 add hostsfile output in addition to statefile
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.
Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
```
Specifications:
* CPU: Qualcomm IPQ8074A, SoC Version: 2.0, Quad core 1651 MHz
* RAM: 1 GiB of DDR3 466 MHz
* Flash: NAND 512 MiB (Winbond W29N04GZ)
* 6 RGB LEDs: Power, LAN1, LAN2, 2.4GHz, 5GHz H and 5GHz L
* UART: One 4-pin populated header next to the heatsink and a chip.
GND RXD TXD, beginning from the external antennas. 115200n8.
Lan:
* One 100/1000/2.5GBASE-T Gigabit Ethernet 802.3bt/at
* One 100/1000 Gigabit Ethernet
Wlan:
* 4x4 in 2.4GHz : 802.11b/g/n/ax
* 4x4 in 5.0GHz L: 802.11a/n/ac/ax
* 4x4 in 5.0GHz H: 802.11a/n/ac/ax
* OFDM and OFDMA
* Bidir and MU-MIMO
* Internal antenna 2.86/4.41/4.98 dBi (2.4GHz/5GHz L/5GHz H)
Power:
* 802.3bt/at 30.1W
* DC 12V/3.5A
Mounting: Wall and ceiling
```
```
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
2. Connect to the console on the AP, and connect the LAN port to your LAN
3. Stop auto boot to get to U-boot shell, interrupt the autoboot process by pressing '0' when prompted
4. Set active_fw in env
4. Set active_fw in env
# setenv active_fw 1
5. Transfer the initramfs image with TFTP
# setenv serverip 192.168.1.10 (IP of TFTP server host)
# setenv ipaddr 192.168.1.1 (IP used by the router for getting the image, must be in the same subnet as the TFTP host)
# tftpboot openwrt-qualcommax-ipq807x-netgear_wax630-initramfs-uImage.itb
6. Reboot and load the image
# bootm
7. SCP factory image to the AP
# scp openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi root@192.168.1.1:/tmp/
8. Connect to device using SSH (use the LAN port)
9. Flash squashfs-factory.ubi from within the initramfs instance of OpenWRT
Before you flash, please check your mtd partitions where mtdX is the right mtd rootfs partition.
# cat /proc/mtd (To check MTD partitions)
# ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq807x-netgear_wax630-squashfs-factory.ubi
10. Set active_fw to 0
# /usr/sbin/fw_setenv active_fw 0
11. Reboot the AP and your done
# reboot
```
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Contains the following update:
52a1c29 ipq8074: add Netgear WAX630 Board file for Netgear WAX630. Extracted from stock (WAX630_BDF.bin) firmware and repacked.
e7701b8 ipq8074: update RegDB in new submitted BDF
cd04ab7 qcn9074: update RegDB in new submitted BDF
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
As requested by the maintainers, the order for the WAX family
should be alphabetically. WAX620 is now after WAX218.
Files changed:
+ipq807x.mk
+01_leds
No changes to the content.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Allwinner H6 needs this driver to enable DVFS support.
May also be used with H616/H618 SoC in the future.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Kernel 5.15 already supports the NanoPi R1 and NanoPi R1S H5,
and they use new LED bindings that do not match the existing
settings in 01_leds. Update led settings to fixes that.
List the led node on NanoPi R1S H5:
root@OpenWrt:~# ls /sys/class/leds/
green:lan green:wan red:status
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Remove ABI version, since its format is not accepted by the linker.
Enable rpath to avoid clash with system libraries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
CONFIG_USB_AUDIO is a "USB Audio Gadget" driver, not a usb device driver
CONFIG_USB_AUDIO is "USB Audio support" before linux 2.6
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Expose the temperature sensors as hwmon, it improves the overall
user experience since on tiny boards the nvme can become a substantial
source of heat.
Signed-off-by: Luca Barbato <lu_zero@gentoo.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
This will help switching to newer 5.15 kernels. This backport required
rebasing Northstar's USB host patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
