Commit Graph

59806 Commits

Author SHA1 Message Date
Eneas U de Queiroz
375dd23011 mac80211: only build ath10k with smallbuffers
When both variants of ath10k drivers are selected, any driver that is
selected along is being built twice, one for each ath10k variant.

Avoid these redundant builds by introducing an optional second parameter
to config_package that lists the variants for which the package is to be
built.

If the symbol is to be set for all of the variants, $(ALL_VARIANTS) can
be used.  This is the case for the mac80211 and cfg80211 modules.  If
the parameter is empty, then the module will be selected and thus built
when the first variant is compiled.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2024-02-23 14:02:53 +01:00
Eneas U de Queiroz
4390ea484d mac80211: build each variant in its own dir
Having different build directories is the default when the package
Makefile defines more than one variant.

Mac80211 overrides PKG_BUILD_DIR, not taking different variants in
consideration, which causes clobbering the directories when both
variants are built.

When compiled with AUTOREMOVE=y, the effect is that the package is
unnecessarily rebuilt when the package is compiled again.

Wihout AUTOREMOVE, the problem is worse: the second variant will not be
rebuilt, and you end up with the smallbuffers variant being a copy of
the regular one.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2024-02-23 14:02:53 +01:00
Paweł Owoc
70fd815e57 qualcommax: ipq807x: add support for Linksys MX5300
Hardware specification:
========
SoC: Qualcomm IPQ8072A
Flash: 512MB (Winbond W29N04GZBIBA)
RAM: 1GB (2x Nanya DDR3L NT5CC256M16ER-EK)
Ethernet: 5x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 5GHz ac 4x4 (Qualcomm QCA9984 + Skyworks SKY85746-11) - channels 100-169
WiFi2: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64
WiFi3: 2.4GHz ax 4x4 (Qualcomm QCN5024 + Skyworks SKY8340-11)
IoT: Bluetooth 5, Zigbee and Thread (Qualcomm QCA4024 + Skyworks SE2433T-R)
IoT Flash: 4MB (Macronix MX25R3235F)
RTC: ST M41T00S
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset

Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin image.
More details can be found here: https://www.linksys.com/hk/support-article?articleNum=274497
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel

2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
  nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
  nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel

3. Installation from initramfs image using USB FAT32 formatted drive:
Stop u-boot and run:
- usb start && fatload usb 0:1 $loadaddr openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx5300-squashfs-factory.bin alt_kernel

4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX5300_1.1.9.200251_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX5300_1.1.9.200251_prod.img alt_kernel

5. USB recovery:
- fw_setenv usbimage 'openwrt-qualcommax-ipq807x-linksys_mx5300-initramfs-uImage.itb'
  fw_setenv bootusb 'usb start && fatload usb 0:1 $loadaddr $usbimage && bootm $loadaddr'
  fw_setenv bootcmd 'run bootusb; aq_load_fw && if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'

Notes:
========
IoT device is accesible over spi. Not yet supported.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
2024-02-23 13:34:59 +01:00
Robert Marko
ac77b45b08 qualcommax: ipq807x: add patch for QUP4 SPI node
Add node to support the QUP4 SPI controller inside of IPQ8074.
Some devices use this bus to communicate to a Bluetooth controller.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-02-23 10:52:52 +01:00
Paweł Owoc
278401e37a qualcommax: ipq807x: reordering, combine the same commands
Reordering, combine the same commands for ipq807x devices

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
2024-02-23 10:52:52 +01:00
Alan Luck
e222c8054c ramips: fix and clean up D-Link MAC address
add back WIFI eprom addresses pointer in mt7621_dlink_dir-xx60-a1.dtsi
Change MAC address pointer from factory_e006 to factory_e000 + 3
	same as used in D-link firmware 1.11 DIR-1960-A1
	DIR-1960-A1,DIR-2640-A1,DIR-2660-A1,DIR-3060-A1

Clean-up MAC addresses in D-Link NOR devices DTS's
Change WIFI MAC Addressees to the same as NAND cousins macaddr_factory_e000 + ?
	as later devices don't have the MAC address in factory configuration
	same as used in D-Link firmware 1.30 DIR-878-A1
	DIR-867-A1,DIR-878-A1,DIR-878-R1,DIR-882-A1,DIR-882-R1,DIR-1935-A1

* D-link software differs between source of wan address

Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
2024-02-22 22:53:30 +01:00
Rafał Miłecki
788122cc12 base-files: sysupgrade: rename add_*files() functions
Usage of word "add" was somehow misleading in those functions:
1. They don't really add (as in: append) anything. Result files are
   created from scratch.
2. It wasn't clear what adding files means. It could be understood as
   adding actual files somewhere (to existing archive?).

Also the word "add" was also a bit ambiguous.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-22 22:19:13 +01:00
Rafał Miłecki
4a1b94adba base-files: sysupgrade: s/do_save_conffiles/create_backup_archive/
Rename function to more accurate and self-explanatory name:
1. Use "archive" in name as this functions creates tar archive
2. Avoid "conffiles" as this function may archive more than that

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-22 22:19:01 +01:00
Rafał Miłecki
4ba5eba94c base-files: sysupgrade: exit with no error for --help
Calling "sysupgrade --help" should result in printing help and exiting
with 0 code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-22 22:18:36 +01:00
Rafał Miłecki
73da77fd00 base-files: sysupgrade: group & cleanup global variables
Group & describe them by type, drop unneeded exports.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-22 22:18:36 +01:00
Rafał Miłecki
57be93c16d base-files: sysupgrade: replace UMOUNT_ETCBACKUP_DIR with a local variable
It was used inside do_save_conffiles() only.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-22 22:18:36 +01:00
Luiz Angelo Daros de Luca
61ac147bb6 base-files: sysupgrade: fix error message and typo
Some minor error message and comment fixes.

Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
2024-02-22 22:14:54 +01:00
Rafał Miłecki
157d6019df Revert "base-files: sysupgrade: always setup overlay when creating backup"
This reverts commit 4fa9aaf0be.

That seemed like a good idea allowing us to include any runtime
generated file in archive. Unfortuantely it broke backups with files
from mounted directories.

When mounting overlay with / as lowerdir its mounts don't propagete in
the mountpoint. That resulted in empty directories:
/tmp/overlay.XXXXXX/backup/tmp/
/tmp/overlay.XXXXXX/backup/var/
/tmp/overlay.XXXXXX/backup/dev/
/tmp/overlay.XXXXXX/backup/proc/
etc.

As some platforms / users try to backup files like /var/dhcp.leases or
/boot/cmdline.txt it means we can't use that solution.

Link: http://lists.openwrt.org/pipermail/openwrt-devel/2024-February/042320.html
Link: https://lore.kernel.org/linux-fsdevel/67bb0571-a6e0-44ea-9ab6-91c267d0642f@gmail.com/T/#u
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-22 22:08:14 +01:00
Rafał Miłecki
7bffa8ab10 Revert "base-files: sysupgrade: include uci-defaults script disabling services"
This reverts commit bf304d10e9.

That uci-defaults script worked great but generating it required
mounting root dir as overlay lowerdir that needs to be reverted.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-22 22:08:04 +01:00
Hauke Mehrtens
5df7a78e82 wifi-scripts: Support HE Iftypes with multiple entries
With mac80211_hwsim I have seen such entries in OpenWrt 22.03:
    HE Iftypes: managed, AP
The mac80211.sh script did not detect the entry and failed. Allow
arbitrary other entries before to fix this problem.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-02-22 21:45:44 +01:00
Tianling Shen
08e249d43c rockchip: remove LED label hack
Now we support parsing the color and function properties.
Ref: e814acc599 ("base-files: support parse DT LED color and function")

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-02-22 17:30:05 +01:00
Yegor Yefremov
62acd9a2f9 dnsmasq: rework network interface ignore
In some situations (slow protocol or interfaces with auto 0), the
interfaces are not available during the dnsmasq initialization and
hence, the ignore setting will be skipped.

Install an interface trigger for ignored interfaces in case their
ifname cannot be resolved.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2024-02-22 09:17:25 +01:00
Jo-Philipp Wich
97ad8501ad ucode: update to Git HEAD (2024-02-21)
ee4af9b55cb4 vm: rework object iteration
a275399dd8e2 uci: refactor uci.changes() to match documentation
ba3855ae3775 lib: fix documentation typo for `pop()` function

Fixes: https://github.com/jow-/ucode/issues/188
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2024-02-22 09:17:25 +01:00
Mantas Pucka
44168fda78 qualcommax: ipq60xx: Add 8devices Mango DVK
8devices Mango DVK is a single board computer / devkit for 8devices Mango
system-on-module (SoM).

Specifications:
* CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz
* RAM: 512 MB
* Storage:
    * 32 MB serial NOR flash (on SoM)
    * 256 MB parallel NAND flash (on DVK)
* Ethernet:
    * 2x1G RJ45 ports(QCA8072 or QCA8075)
    * 1x2.5G RJ45 port (QCA8081)
    * 1xSFP (shares SGMII with QCA8081)
* Switch: Qualcomm Atheros IPQ6010
* WLAN:
    * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate
    * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate
* USB:
    * 1x USB3.0 Type-A port
    * 1x USB2.0 available at mini PCIe slot
* PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s)
* SD/eMMC (on a single shared bus - only one can be active):
    * micro SD slot
    * eMMC module connector
* LEDs:
    * Green power led (not controllable)
    * Green 2.4GHz radio led (GPIO 67)
    * Green 5GHz radio led (GPIO 66)
* Buttons:
    * 1x (WPS GPIO79) button
* GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level)
* UART: 4-pin UART header (3.3V level)
    * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2)
* Power:
    * PoE IN on 2.5G port (passive 24-48V)
    * DC power terminal (12-58V)

Installation instructions:

Vendor image format is compatible with squashfs-sysupgrade image. Run:

sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-02-21 21:42:23 +01:00
Mantas Pucka
10ba730b7b ipq-wifi: add support for 8devices Mango board
Add support for .ipq6018 BDF suffix and add Mango board entry

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-02-21 21:42:23 +01:00
Mantas Pucka
03935cf7de ipq-wifi: update to Git HEAD (2024-02-19)
1cc59e1 ipq6018: add 8devices Mango BDF
10279cc ipq40xx:Add support for Netgear LBR20 with two BDF's

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-02-21 21:42:23 +01:00
Mantas Pucka
586a051d4d ath11k-firmware: add wifi firmware for ipq6018
So far only stable FW is v2.4. It exists in a different
git repo, so add custom download routine.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-02-21 21:42:23 +01:00
Mantas Pucka
aa6cc0a52b mac80211: ath11k: disable coldboot for ipq6018
Coldboot calibration does not work at the moment and causes failure during
wifi startup.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-02-21 21:42:23 +01:00
Mantas Pucka
d08d53346b qca-ssdk: support selecting PCS channel for PORT3 on IPQ6018
When QCA8072 is used in PSGMII mode with IPQ6018, PCS used for second
PHY port would overlap with one used by SGMII+ port. SoC has register
to select different PCS in such case.

Original code used PHY_ID for this decision, which also had other
issues, but is no longer viable since we moved to upstream QCA807x
driver.

Introduce DT property port3_pcs_channel to allow describing this in DT.
Default value is <2>, and for some QCA8072 designs <4> would be needed.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-02-21 21:42:23 +01:00
Mantas Pucka
548c5935bf qualcommax: ipq60xx: set correct PHY mode for port 0-4
[port 8ed390a (qualcommax: set correct PHY mode for port 0-4) to ipq60xx]

Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
he upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.

Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq6018-ess.dtsi.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
2024-02-21 21:42:23 +01:00
Paweł Owoc
568f38a56b qualcommax: ipq807x: skip factory.ubi image for MX4200
Skip building not used factory.ubi image

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
2024-02-21 21:26:57 +01:00
Paweł Owoc
e670a939cd qualcommax: ipq807x: remove duplicated sysupgrade image definitions
Image sysupgrade.bin is defined by default and there is no need to define it.

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
2024-02-21 21:26:57 +01:00
Paweł Owoc
2b82c87b1f qualcommax: ipq807x: fix variable definition
Fix variable definition, prevent displaying warnings:
- warning: overriding recipe for target
- warning: ignoring old recipe for target

Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
2024-02-21 21:26:57 +01:00
Felix Fietkau
2a752ff028 mac80211: add a fix for racy drv_sta_rc_update calls
Fixes potential crash issues in mt76 and other drivers

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-02-21 15:28:53 +01:00
Shiji Yang
01996b785d ramips: clean up useless dts partition labels
The previous NVMEM eeprom conversions[1][2] left a lot of partition
labels that were no longer used. They can be removed now.

[1] https://github.com/openwrt/openwrt/pull/13584
[2] https://github.com/openwrt/openwrt/pull/13587

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2024-02-21 13:31:18 +01:00
Marius Durbaca
c22c63bce3 rockchip: add Radxa CM3 IO board support
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC

Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.

Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
2024-02-21 13:29:26 +01:00
Marius Durbaca
4821cb24ed uboot-rockchip: add Radxa CM3 IO board support
Add support for the Radxa CM3 IO board.

Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
2024-02-21 13:29:26 +01:00
Marius Durbaca
eec0bec630 rkbin: add rk3566 atf/tpl blobs
Currently there are no atf/tpl blobs for rk3566 SoCs
so this commit adds the prebuilt firmware from the vendor.

Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
2024-02-21 13:29:26 +01:00
Felix Fietkau
95e633efbd mac80211: add AQL support for broadcast/multicast packets
Should improve performance/reliability with lots of mcast packets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-02-21 10:56:22 +01:00
Robert Marko
fb45887e85 mac80211: update to 6.6.15
Update backports to the latest 6.6 point release.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2024-02-21 10:56:22 +01:00
Christian Marangi
4883e4c04f
generic: replace simple AQR hack patch with upstream version
Simple AQR hack patch has been merged upstream, hence we can drop it from
hack directory and move it to backport.

The patch for 5.15 are correctly reworked to align to outdated API.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-02-21 02:34:32 +01:00
Daniel Golle
c42b915af0 build: don't drop 'user' flag when using the ImageBuilder
Commit be9023ed43 ("build: fix opkg flags in rootfs") introduced a
call to 'awk' which removes the 'user' flag from all installed
packages in the opkg status file. While is is somehow desireable when
building images directly within the buildroot, when using the
ImageBuilder dropping the 'user' flag means loosing information about
a package being deliberately selected or just implicitely pulled as a
dependency. And that then break tools like 'auc' which request only
packages having the 'user' flag from the asu server, resulting in
broken images being delivered to users.

Restore the original behavior in case of an image being created using
the ImageBuilder.

Fixes: be9023ed43 ("build: fix opkg flags in rootfs")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-02-20 21:18:44 +00:00
Oto Šťáva
1e93208bd2
build: add explicit --no-show-signature for git
When `log.showSignature` is set, it causes the `SOURCE_DATE_EPOCH` to
include a textual signature description on OpenPGP-signed commits,
because Git prints the description into stdout. This then causes some
scripts to fail because they cannot parse the date from the variable.

Adding an explicit `--no-show-signature` prevents the signatures from
being displayed even when one has Git configured to show them by
default, fixing the scripts.

Signed-off-by: Oto Šťáva <oto.stava@gmail.com>
2024-02-20 20:57:53 +01:00
Rafał Miłecki
ae036c26fd mediatek: filogic: fix mt7981 DT nodenames
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-20 12:42:28 +01:00
Rafał Miłecki
6bda7d2090 mediatek: filogic: improve mt7981 DT coding style
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-20 12:42:28 +01:00
Rafał Miłecki
388bc4b365 mediatek: filogic: reorder mt7981 DT properties
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-20 12:42:28 +01:00
Rafał Miłecki
faa7b7dd0a mediatek: filogic: reorder mt7981 DT SoC reg-based nodes
Follow upstream Linux kernel guidelines:
https://www.kernel.org/doc/html/next/devicetree/bindings/dts-coding-style.html#order-of-nodes

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-20 12:42:28 +01:00
Rafał Miłecki
c094131c1a mediatek: filogic: reorder mt7981 DT name-based nodes
Follow upstream Linux kernel guidelines:
https://www.kernel.org/doc/html/next/devicetree/bindings/dts-coding-style.html#order-of-nodes

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2024-02-20 12:42:28 +01:00
Robert Marko
63f7ced2f0 generic: 6.1: add missing symbol for EN8811H PHY driver
Disable Airoha EN8811H PHY driver by default to avoid individual targets having to
disable it.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-02-19 21:40:06 +01:00
Tianling Shen
afca1236f3 rockchip: add NanoPi R4S Enterprise Edition build
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.

This patch switched to use that upstreamed dts and removed local
EEPROM patch.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-02-19 20:52:06 +01:00
Martin Garbe
873b0ed42c ath79: update WA/XC devices UBNT_VERSION to 8.7.4
Ubiquiti WA devices with newer hw version (sold 2023)
require UBNT_VERSION to be at least 8.7.4, otherwise
the image is rejected.

For consistency, also increase version number for XC devices.

Signed-off-by: Martin Garbe <monomartin@opennet-initiative.de>
2024-02-19 16:51:39 +01:00
Tianling Shen
782266473d rockchip: add NanoPi R2C Plus support
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-02-19 16:23:32 +01:00
Tianling Shen
23cb2b1636 uboot-rockchip: add NanoPi R2C Plus support
Add support for the FriendlyARM NanoPi R2C Plus.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2024-02-19 16:23:32 +01:00
Chukun Pan
4108c0c1b6 qualcommax: backport more changes for ipq6018 and ipq8074
- Mark patches as upstream
 - Backport more upstream changes
 - Handle conflicts and refresh patches

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-02-19 15:01:12 +01:00
Rafał Miłecki
bf304d10e9 base-files: sysupgrade: include uci-defaults script disabling services
Disabled services should be kept disabled after sysupgrade. This can be
easily handled using a proper uci-defaults script.

Extend sysupgrade to check for disabled services, generate uci-defaults
script disabling them and include it in backup.

Cc: Christian Marangi <ansuelsmth@gmail.com>
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2024-02-19 13:53:14 +01:00