The WAN LED now shows the link state. It's color is green,
not blue.
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
(cherry picked from commit 0411813c6f)
The tar extraction depends on the order in which the files
are added to the tar file. Since the order is not guaranteed
and depends on the host system, the combined mtd write fails
with sysupgrade images built on some systems.
Fix by changing to tar file order independent mtd write.
Fixes: 86e18f6706 ("ipq806x: add support for OpenMesh A42")
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This remedies an issue with the MBL Duo if both disks are inserted
and contain OpenWrt. kernel and dtb would be loaded from SATA 1:1
while rootfs (/dev/sda2) would be mounted on SATA 0:1.
Such a mix&match would obviously only work if both OpenWrt versions/
builds are identical, and especially fail after sysupgrade upgraded
the system disk on SATA 0:1.
The fallback to SATA 1:1 needs to be kept for MBL Single (only has
SATA 1:1) and MBL Duo with one disk inserted on SATA 1:1. To speed
up booting in those cases, the unneccesarily doubled "sata init"
will only be called once. (In theory it could be omitted completely
since the on-flash boot script already initializes SATA to load the
on-disk boot script.)
Tested on MBL Duo (all possible combination of disks) and MBL Single
Signed-off-by: Freddy Leitner <hello@square.wf>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
This was not converted to the new, dt-based board name.
Fixes: e90dc8d272 ("apm821xx: convert to device-tree board detection")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There was a bug in ubifs related to the O_TMPFILE. When reapplying
changes after power cut data could be lost. This problem was exposed by
overlayfs and the upstream commit 3a1e819b4e80 ("ovl: store file handle
of lower inode on copy up").
This fixes a regression introduced when switching from 4.9 to 4.14.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit c6a1bcac16)
This target has been on 4.14 for a long time now.
Remove these leftovers as it interferes with kernel bumping.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
It's needed to support new devices that use specific pin functions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0cf32de17c)
It's required to support devices using adjustable SoC pins for some
specific purpose (e.g. I2C, PWM, UART1).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit f00cb94f7c)
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:
- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G
and probably other Mikrotik boards need this patch as well.
The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/
Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
[Rebased + refreshed on current kernels]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Following errors were seen in the past on imx6 when using serial:
[ 22.617622] imx-uart 2020000.serial: DMA transaction error.
[ 22.623228] imx-uart 2020000.serial: DMA transaction error.
[ 22.628826] imx-uart 2020000.serial: DMA transaction error.
[ 22.648951] imx-uart 2020000.serial: DMA transaction error.
[ 22.654558] imx-uart 2020000.serial: DMA transaction error.
[ 22.660156] imx-uart 2020000.serial: DMA transaction error.
Which is the reason why DMA for the serial ports
got disabled in commits:
efb362cd93 ("imx6: disable dma on uart")
3b4241071d ("imx6: disable UART dma")
As indicated on mailinglist discussion, the cause seems to be
the usage of very old SDMA firmware which is present in the soc:
[ 0.624302] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[ 0.624318] imx-sdma 20ec000.sdma: Falling back to user helper
[ 64.531607] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
This patch adds the new firmware binary. (2196 bytes)
It is required to embed the binary into the kernel image, as it
gets loaded very early in the boot process where the rootfs is not
available yet:
[ 0.622966] imx-sdma 20ec000.sdma: loaded firmware 3.3
Extended testing shows that the DMA errors are not seen anymore
when using this newer firmware version.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
starting from upstream commit 577b4eb23811 ("ubi: Reject MLC NAND")
it is not allowed to use UBI and UBIFS on a MLC flavoured NAND flash chip. [1]
According to David Oberhollenzer [2]:
The real problem is that on MLC NAND, pages come in pairs.
Multiple voltage levels inside a single, physical memory cell are used to
encode more than one bit. Instead of just having pages that are twice as big,
the flash exposes them as two different pages. Those pages are usually not
ordered sequentially either, but according to a vendor/device specific
pairing scheme.
Within OpenWrt, devices utilizing this type of flash,
combined with UBI(fs) will be bricked when a user upgrades
from 17.01.4 to a newer version as the MLC will be refused.
As these devices are currently advertised as supported by OpenWrt,
we should at least maintain the original state during the lifecycle
of the current releases.
Support can be gracefully ended when a new release-branch is created.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.e>
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.14.77&id=577b4eb23811dfc8e38924dc476dbc866be74253
[2] https://lore.kernel.org/patchwork/patch/920344/
This just moves patch to use 0xx prefix and includes maintainer's s-o-b.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 9b385b2496)
Instead of reverting whole commit it's enough to just revert a single
line change. It seems the real problem with the regressing commit was a
bump of read chunk size. Switching back to 256 B chunks is enough to fix
the problem/regression.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 92de28b751)
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
In commit 9e1530b2a3 ("kernel: bump 4.9 to 4.9.117 for 18.06") [1], the following patch for removed:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
This patch contained fixes for both write and erase functions.
While the chip-detects for erase got fixed upstream [2],
some modifications are still required, even with the fixes applied.
Not doing so results in following errors seen:
Collected errors:
* pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error.
* opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain!
* opkg_install_cmd: Cannot install package luci-ssl.
* opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error.
[ 0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.423476] mount_root: switching to jffs2 overlay
[ 270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962
[ 270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe
Fixes: 9e1530b2a3 ("kernel: bump 4.9 to 4.9.117 for 18.06")
Signed-off-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Compaction is the only memory management component to form high order (larger
physically contiguous) memory blocks reliably. The page allocator relies on
compaction heavily and the lack of the feature can lead to unexpected OOM
killer invocations for high order memory requests. You shouldn't disable this
option unless there really is a strong reason for it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
The install_bin from /lib/upgrade/common.sh is no longer creating the
symlinks when a secondary parameter is added. But the fw_setenv program was
always copied this way to the ramdisk for the upgrade.
Instead, just install fw_setenv and let install_bin handle the detection of
the required dependencies.
Fixes: 438dcbfe74 ("base-files: automatically handle paths and symlinks for RAMFS_COPY_BIN")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Buttons of AVM FritzBox 4020 are incorrectly flagged as active high.
This was an oversight as RFKill button was working as expected even
with incorrectly flagged GPIO.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cd02d4faf9)
The sysupgrade image failed the check due to the wrong string in the
supported devices. This patch provides the correct name by dropping the
SUPPORTED_DEVICES to use the default generated name.
Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net>
[drop the SUPPORTED_DEVICES, the old name was never used in a release]
Signed-off-by: Mathias Kresin <dev@kresin.me>
When building using the multiple devices option with per-device root
filesystem, only the meta package mt76 is omitted but not the
dependencies selected by the package.
Explicitly exclude all 3 mt76 packages, plus the metapackage.
Otherwise, these modules will be included in the build, wasting
a few hundred kilobytes.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[mention the root cause of the issue in the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes regression introduced in kernel 4.14 and makes bcm53xx revert
obsolete.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 43d36606d6)
PCI paths of the WLAN devices have changed between kernel 4.4 and 4.9;
migrate config so existing wifi-iface definitions don't break.
This is implemented as a hotplug handler rather than a uci-defaults script
as the migration script must run before the 10-wifi-detect hotplug handler.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit b452af23a8)
When checking the outcome of the PHY autonegotiation status, at803x
currently returns false in case the SGMII side is not established.
Due to a hardware-bug, ag71xx needs to fixup the SoCs SGMII side, which
it can't as it is not aware of the link-establishment.
This commit allows to ignore the SGMII side autonegotiation status to
allow ag71xx to do the fixup work.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4e39e213af)
The QCA955X is affected by a hardware bug which causes link-loss of the
SGMII link between SoC and PHY. This happens on change of link-state or
speed.
It is not really known what causes this bug. It definitely occurs when
using a AR8033 Gigabit Ethernet PHY.
Qualcomm solves this Bug in a similar fashion. We need to apply the fix
on a per-device base via platform-data as performing the fixup work will
break connectivity in case the SGMII interface is connected to a Switch.
This bug was first proposed to be fixed by Sven Eckelmann in 2016.
https://patchwork.ozlabs.org/patch/604782/
Based-on-patch-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f4f99ec973)
The changed dictionary size leads to a different LZMA header which breaks
sysupgrade image magic checkibng on at least some RT288x boards.
Since the commit message only mentions testing on MT7621 and since the
change appears to break at least one other ramips subtarget, do not take
any chances and restrict the size limitation to only MT7621.
Fixes FS#1797
Fixes 09b6755946 ("ramips: limit dictionary size for lzma compression")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 77e2bccde8)
Netgear WNR612v2 flashed with recent OpenWrt builds suffers from kernel
panic at boot during wireless chip initialization, making device
unusable:
ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
ath: phy0: Enable LNA combining
CPU 0 Unable to handle kernel paging request at virtual address 1000fee1, epc == 801d08f0, ra == 801d0d90
Oops[#1]:
CPU: 0 PID: 469 Comm: kmodloader Not tainted 4.9.120 #0
[ ... register dump etc ... ]
Kernel panic - not syncing: Fatal exception
Rebooting in 1 seconds..
This simple patch fixes above error. It keeps LED table in memory after
kernel init phase for ath9k driver to operate correctly (__initdata
removed).
Also, another bug is fixed - correct array size is provided to function
that adds platform LEDs (this device has only 1 connected to Wifi chip)
preventing code from going outside array bounds.
Fixes: 1f5ea4eae4 ("ar71xx: add correct named default wireless led by using platform leds")
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[trimmed commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The NBG6616 shares a config symbol with the NBG6716. It was accidentally
removed from the config when the ar71xx-tiny target was split off.
Fixes: 0cd5e85e7a ("ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit a4f4ddba61)
The device was not included in the /etc/board.d/02_network file, so
the network wouldn't be properly set up on boot.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
The former used compatibles aren't defined anywhere and aren't used by
the devicetree source files including them.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to abbfcc8525 ("ramips: add support for GL-inet
GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC
compatible to match the used hardware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
RT5350 neither have rgmii nor a mdio pinmux group. MT7628an doesn't
have a jtag group. Having these groups defined might cause a boot
panic.
The pin controller fails to initialise for kernels > 4.9 if invalid
groups are used. If a subsystem references a pin controller
configuration node, it can not find this node and errors out. In worst
case it's the SPI driver which errors out and we have no root
filesystem to mount.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The intention of 967b6be118 ("ar8327: Add workarounds for AR8337
switch") was to remove the register fixups for AR8337. But instead they
were removed for AR8327.
The RGMII RX delay is forced even if the port is used as phy instead of
mac, which results in no package flow at least for one board.
Fixes: FS#1664
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device
min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which
is [68, 1500] by default.
It's necessary to set a max_mtu if a mtu > 1500 is supported.
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following patch was integrated upstream:
* target/linux/generic/backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
This fixes tries to work around the following security problems:
* CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
* CVE-2018-3646 L1 Terminal Fault Virtualization related aspects
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The following patches were integrated upstream:
* target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch
* target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch
This fixes tries to work around the following security problems:
* CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects
* CVE-2018-3646 L1 Terminal Fault Virtualization related aspects
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In "brcm47xx: rework model detection" the file 01_detect was moved
to 01_network, therefore also update the warning message in case
everything fails.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The flash size of the ubnt2 and ubnt5 is limited and the images with
LuCI are getting too big for these boards. Do not build images for these
boards to make the complete build of this target not fail anymore.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kernel image of the at91-q5xr5 is getting too bing now and this is
breaking the build. Remove the image for the at91-q5xr5 from the build
to at least build images for the other devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They're already in linux.git, so they shouldn't be in pending.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 14b6c72541)
The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.
The final two patches of this series are already in the kernel, so no
need to include them here.
Patchwork: https://patchwork.ozlabs.org/cover/881776/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit ef025e6417)
Backport an upstream fix for a remotely exploitable TCP denial of service
flaw in Linux 4.9+.
The fixes are included in Linux 4.14.59 and later but did not yet end up in
version 4.9.118.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit fefe1da440)
Refreshed all patches.
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(backported from commit f7036a34ac)
In boards with fdt is impossible to use kmod-w1-gpio-custom.
w1-gpio-custom create platform structure for w1-gpio module,
but if board use fdt, data is ignored in w1-gpio probe.
This workaround fix the problem.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cherry picked from commit aa5838adb7)
Add two patches submitted for upstream review that significantly improve
the dwc2 driver on openwrt from kernel stability and performance
perspectives.
Fixes: FS#1367
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
(cherry picked from commit 9f451ec698)
This reverts commit b40316c21a.
That change causes ramips/mt7620 to fail with:
drivers/net/ethernet/mtk/gsw_mt7620.c: In function 'mt7620_hw_init':
drivers/net/ethernet/mtk/gsw_mt7620.c:171:14: error: 'mdio_mode' undeclared (first use in this function); did you mean 'd_move'?
} else if (!mdio_mode) {
^~~~~~~~~
d_move
Back it out for now to restore compilation.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.
This mitigates CVE-2018-3639 on ARM64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 77e3e706ce)
To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)
when port4 setup to work as gmac mode, dts like:
&gsw {
mediatek,port4 = "gmac";
};
we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0
before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY
after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit f6d81e2fa1)
When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.
Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
(cherry picked from commit 379fe50672)
* Refreshed patches.
* Removed patches:
- target/linux/ar71xx/patches-4.9/103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch superseded by upstream
- target/linux/ar71xx/patches-4.9/403-mtd_fix_cfi_cmdset_0002_status_check.patch superseded by upstream
- target/linux/brcm63xx/patches-4.9/001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch accepted upstream
- target/linux/brcm63xx/patches-4.9/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch accepted upstream
- target/linux/brcm63xx/patches-4.9/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch accepted upstream
- target/linux/generic/pending-4.9/900-gen_stats-fix-netlink-stats-padding.patch
* New backported patch to address ext4 breakage, introduced in 4.9.112:
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9
Thanks to Koen Vandeputte for pointing out the need to add the ARM64_SSBD symbol, and the ext4 patch.
Compile-tested on: ar71xx
Run-tested on: ar71xx
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
This includes Linksys EA9500 support, BCM53573 timer fix and
upstream-ready partitions patch that replaces two downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a07730472c)
USB 3.0 PHY is attached to the MDIO bus and should be supported
(accessed) as a MDIO device. This wasn't known initially which resulted
in writing driver that was working with MDIO bus (using some magic
values) without knowing it.
This commit updates DT to properly describe MDIO & USB 3.0 PHY and
enables required kernel drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 8a175ea219)
This is a new & warm feature that allows nesting partiitons in DT and
mixing their types (e.g. static vs. dynamic). It's very useful for
boards that have most partitions static but some of them require extra
parsing (e.g. a "firmware" partition).
It's required to successfully backport support for new devices using
that new syntax in their DT files.
Since brcm63xx has a custom alternative patch the upstream one is being
reverted for it. The plan is to make brcm63xx use the upstream
implementation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 2a598bbaa3)
Two tiny & trivial patches with no regression risk. One simplifies
bcm53xx downstream patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 6bcafea2c0)
The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches
break the possibility for using an ip4ip6 tunnel interface as a fall
back interface accepting ip4-in-ip6 tunneled packets from any remote
address. This works out of the box with any normal (non-666-patched)
kernel and can be configured by setting up an 'ip -6 tunnel' with type
'any' or 'ip4ip6' and a remote address of '::'.
The misbehavior comes with line 290 the patch which discards all packets
that do not show the expected saddr, even if no single fmr rule was
defined and despite the validity of the saddr was already approved earlier.
Signed-off-by: Axel Neumann <neumann@cgws.de>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from 65c05301c2)
AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.
Fixes: f791fb4af4 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9 ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 67fcff6aaf)
The patch was wrongly removed by a kernel version bump to 4.9.106 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.
Fixes: 6f8eb1b50f ("kernel: bump 4.9 to 4.9.106 for 18.06")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit a497e47762)
This reverts commit 3442ec5d57.
The device behaviour is reportedly erratic so let's not take chances and
leave this out for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Qxwlan E750G v8 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (PoE support)
- 2x 10/100/1000 Mbps Ethernet
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit 53a4502013)
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit ac03d51a3f)
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit b74f63f81d)
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7516a96011)
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.
Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.
This patch fixes these issues and renames the corresponding #defines for
clarity
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit e99f760235)
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.
Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.
As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.
Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.
Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit d7d10f2c1e)
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0417b08b06)
This fixes kernel hang when booting on BCM4718A1 (& probably BCM4717A1).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4c1aa64b4d)
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC. However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines. If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.
This commit overrides the incorrect dt node definition in the included
file.
See also:
- https://bugs.openwrt.org/index.php?do=details&task_id=1262
- https://community.nxp.com/thread/338432#comment-474107
Signed-off-by: Tim Small <tim@seoss.co.uk>
(cherry picked from commit e97aaf483c)
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" fixes the
freezes according to @takimata, @And.short, that have been
reported on the forum by @ticerex.
Furtheremore, @takimata reported that the patch also improved
the performance of the HDDs considerably:
|<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/55>
|It seems your patch unleashed the full power of the SATA port.
|Where I was previously hitting a really hard limit at around
|82 MB/s for reading and 27 MB/s for writing, I am now getting this:
|
|root@OpenWrt:/mnt# time dd if=/dev/zero of=tempfile bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 13.65s
|user 0m 0.01s
|sys 0m 11.89s
|
|root@OpenWrt:/mnt# time dd if=tempfile of=/dev/null bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 8.41s
|user 0m 0.01s
|sys 0m 4.70s
|
|This means: 121 MB/s reading and 75 MB/s writing!
|
|[...]
|
|The drive is a WD Green WD10EARX taken from an older MBL Single.
|I repeated the test a few times with even larger files to rule out
|any caching, I'm still seeing the same great performance. OpenWrt is
|now completely on par with the original MBL firmware's performance.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.
Also remove unused .dtb references in the mt7623 subtarget.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 8194f9ef4a)
Starting with 4.14, the "amcc,dwc-otg" needs to be used
in order to get the usb-otg to work.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 12b80f1cab)
This commit adds the get_status_led method to diag.sh, which sets the
boot-led as status-led for scripts using this method to get a
status-led.
This method is used platform-independent in downstream project gluon to
set the LED used to indicate the config-mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4fc005197a)
Backport hot off the press upstream netlink patch. Fixes stats display
from CAKE qdisc on MIPS allowing us to bump CAKE to latest version.
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 3698b34a00)
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align
Let the MTD core take care of both
Fixes messages like these:
[ 102.820541] Data buffer not 16 bytes aligned: 87daf08c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The line that produces factory image was accidentally left by me while
testing before inital commit.
I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).
I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.
So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refreshed all patches
Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.
This fixes UBI support for devices that have kernel flashed on partition
with a bad block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7ddba08d87)
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.
Fixes: FS#1620
Signed-off-by: Mathias Kresin <dev@kresin.me>
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.
Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move to i2c pins pinmux node to the pinctrl node.
Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")
Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.
Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
[ 1.111324] 0x000001480000-0x000001880000 : "kernel"
[ 1.121005] 0x000001880000-0x000007900000 : "ubi"
[ 1.283912] 0x000007900000-0x000008000000 : "reserve"
[ 1.296407] 0x000001480000-0x000007900000 : "firmware"
[ 1.468043] no rootfs found after FIT image in "firmware"
[ 2.426860] 2 uimage-fw partitions found on MTD device firmware
[ 2.426931] 0x000001480000-0x000001880000 : "kernel"
[ 2.440420] 0x000001880000-0x000007900000 : "ubi"
Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
Writing from <stdin> to kernel ...
ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
ubiattach: error!: bad MTD device number: "6 mtd10"
The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.
Only tested for the R7800 but all of them should behave equal.
Fixes: FS#1617
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.
Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.
In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.
Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit
Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52
Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0
1-4: lan
0: wan
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 5c5bf8b865)
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.
Code was written mostly by Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2524febf79)
This fixes missing rootfs on above device:
[ 2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[ 2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e53d0da775)
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
set device and tftp server IP address and input the firmware
file name. U-boot will then load the firmware and write it into
the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Arvid E. Picciani <aep@exys.org>
(cherry picked from commit bf39d5594b)
This commit adds support for the AVM Fritz!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- Most LEDs
Not working:
- 2 RSSI LEDs
AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
While it is possible to implement this feature, it would require an
additional kernel patch for a minor functionality.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b4bf43c667)
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
(cherry picked from commit 4b280ad91a)
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit e36f8b3f39)
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.
This commit fixes this behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit abb4ab076f)
This commit adds support for the Mikrotik RouterBOARD RBM33g.
=Hardware=
The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.
==Switch==
The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:
port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU
==Flash==
The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.
==PCIe==
The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.
Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:
PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11
==USB==
The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:
open: USB on PCIe 1 is active
closed: USB on rear USB port is active
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.
=Installation=
==Prerequisites==
A USB -> RS-232 Adapter and a null modem cable are required for
installation.
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**
Serial settings: 115200 8N1
The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet
On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"
Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 57600 bps
Flash instruction using factory image:
1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新（アップデート）")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.
Specification:
- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
[...]
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k 0000:00:00.0: enabling device (0000 -> 0002)
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
ath9k 0000:00:00.0: request_irq failed
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k: probe of 0000:00:00.0 failed with error -22
The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link never came up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
advk-pcie d0070000.pcie: config read/write timed out
Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.
The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.
For the record, the iwlwifi and mt76 cards were not affected by this
issue.
1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 772258044b)
Backport a hot off the press upstream kernel ATM fix:
Preserve value of skb->truesize when accounting to vcc
"There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs. Ideally it would cover ATM too. It doesn't. Just
stashing the accounted value and using it in atm_raw_pop() is probably
the easiest way to cope."
The issue was exposed by upstream with:
commit 14afee4b6092fde451ee17604e5f5c89da33e71e
Author: Reshetova, Elena <elena.reshetova@intel.com>
Date: Fri Jun 30 13:08:00 2017 +0300
net: convert sock.sk_wmem_alloc from atomic_t to refcount_t
But an earlier commit left the ticking timebomb:
158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()
Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging
assistance and to David Woodhouse <dwmw2@infradead.org> for further
guidance, cajoling & patience in interpreting the debug I was giving him
and producing a fix!
Fixes FS#1567
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit d600de3ddd)
The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as
dynamic ftrace depends on -mlong-calls.
See http://patchwork.linux-mips.org/patch/675/
Thus we always set -mlong-calls if the kernel is being
compiled with dynamic ftrace support.
Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
(cherry picked from commit 076d2ea682)
This fixup ip align in essedma driver rx path
see cat /proc/cpu/alignment
which reports alignment-fixups without this fix.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit 8f804f42d5)
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.
Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.
These patches backport the workaround from 4.17.
Signed-off-by: Jeremiah McConnell <miah@miah.com>
(cherry picked from commit e820455198)
zram.ko needs CONFIG_BLK_DEV activated and it is by default for all
other targets in OpenWrt.
This makes zram.ko compile again.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6745af9a0d)
Neon and vfpv4 are mandatory extensions in the ARM64 instruction set
now, do not activate them explicitly. GCC will make use of these
extension now by default.
This makes it possible to share the toolchain with other Cortex A53
SoCs.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 10ce015c65)
Some of the Marvell targets have functional SATA port multiplier
support, which is required for multi-bay eSATA enclosures. Enable
kernel support by setting CONFIG_SATA_PMP.
Closes: FS#1232 and FS#547
Signed-off-by: Jeremiah McConnell <miah@miah.com>
(cherry picked from commit 390c4df2c0)
The ART partition of the Lima board stores exactly three mac addresses:
* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac
The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.
Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 4f6320704f)
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit fff65dbe24)
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.
Functional issues:
* PCIe won't come up (hence no USB3 on Shuttle KD20)
* I2C bus of Akitio myCloud device is likely not to work (missing
debounce support in new pinctrl driver)
Code-style issues:
* plla/pllb needs further cleanup -- currently their users are writing
into the syscon regmap after acquireling the clk instead of using
defined clk_*_*() functions to setup multipliers and dividors.
* PCIe phy needs its own little driver.
* SATA driver is a monster and should be split into an mfd having
a raidctrl regmap, sata controller, sata ports and sata phy.
Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(squash-picked commit 17511a7ea8 and commit dcc34574ef from master)
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch
Flash instruction:
The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
With this change, the LED trigger is independent from the (wireless)
netdev name. The (wireless) netdev name can be easiliy changed in
OpenWrt and would require an update of the netdev trigger settings each
time it is done.
This change is (for now) applied only to MT7628 devices from TP-Link, as
we only had the possibility to test this change against two of those
devices, namely a TL-WR841 v13 and a Archer C50 v3.
Signed-off-by: David Bauer <mail@david-bauer.net>
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.
Set the correct register address and size in the dtsi file to get the
watchdog working.
Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This was caused by a race condition between offload teardown and
conntrack gc bumping the timeout of offloaded connections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This device has only one ethernet port.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[add the existing eth0 as lan block, shorten commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AVM package selection partially broke with the addition of the
FRITZ!Box 4020. This commit restores the intended behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.
Toggling a gpio selects the output to which USB is connected.
Since kernel 4.9, gpio base is rounded up to a value of 32.
Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.
But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.
Switching the USB port to mPCIe now shows my modem is correctly discovered again:
[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11
Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 55b4b1eba0)
The kernel bump wrongly modified the patch
generic/pending-4.14/811-pci_disable_usb_common_quirks.patch.
Sync it from master.
Fixes: 1199a91095 ("kernel: bump 4.14 to 4.14.48 for 18.06")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refreshed patches. The following patches were upstreamed and have been deleted:
* target/linux/lantiq/patches-4.14/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
* target/linux/generic/pending-4.14/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
* target/linux/generic/pending-4.14/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
* target/linux/generic/pending-4.14/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Refreshed patches. The following patches were upstreamed and have been deleted:
* target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
* target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
* target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
* target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.
While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.
Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.
Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.
This approach had two issues:
- The padding was only working when .data was non-empty (otherwise the
section would become NOBITS, omitting it in the binary). .data was only
empty when no CMDLINE was set, leading to further workarounds like
fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
workaround was only effective because a missing "const" led to the kernel
argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
uncompressed .bin and .elf loaders. The prevented embedding the kernel
cmdline in the loader for non-gz loader types.
To fix both issues, move the creation of the padding from the linker script
to the gzip step.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The console bootarg is being corrupted on boot, causing various issues
including broken sysupgrade.
Utilising the bootargs mangle patch from other targets, hardcode the console
arguments and fetch the rootfs from the bootloader.
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock8
Bootloader command line (ignored): console= root=/dev/mtdblock8
Please cherry pick to 18.06 too
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
(cherry picked from commit 4fdc6ca31b)
This is a port of an old commit from mkresin's tree:
09260cdf3e9332978c2a474a58e93a6f2b55f4a8
This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 9685f39787)
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.
eg. 2.4GHz working but not 5GHz.
As all of these dts entries are already specified in mt7621.dtsi, remove
them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 02f815d190)
There's nothing connected to i2c on this board, so remove it.
Also edited the gpio group to match the PC2 as they're the same.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 8c818fa1f0)
Switch ports 0..3 are connected to external ports LAN{1..4} in sequence,
switch port 4 is not used, and switch port 5 is connected to the CPU.
The WAN port is attached to the CPU's second network interface; it has no
connection to the internal switch.
Reuse the "Dell TrueMobile 2300" entry, which describes the same mapping.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
(cherry picked from commit 7ac238fc98)
The W25N01GV NAND is currently not used in any ipq806x device.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit a436ef992d)
There's no spi-nor in R7800, so disable unequipped interfaces.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 8c1c1c4874)
These pins seem to be used by hw exclusively, so claiming it in
kernel causes an error in syslog in k4.14+.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 96cd31655d)
EA8500 has pcie2 slot unequipped.
By EA8500 hw design default pcie2 reset gpio (gpio63) is used to
reset the switch. That's why enabling pcie2 brings the switch into
a working state.
So let's just control the gpio63 without enabling the pcie2 slot.
We have to remove the pcie2_pins node so the gpio63 is not defined
twice. Because pcie2 node has a reference to pcie2_pins we have to
remove it as well.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 7f694ef3d9)
These nodes are common for all revisions so put it into SoC v1.0
dtsi file.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 7a4f9c5993)
USB PHY power settings introduced for ipq8065 SoC with commit
644a0d5 "ipq8065: adjust SS USB PHY power settings"
According to that commit msg and in correspondence to GPL tarballs
and related QSDK branch those settings are applied to ipq8064
SoCs of version >= 2.0.
https://github.com/paul-chambers/netgear-r7800/blob/master/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2507-L2514
Now as we have clarified that mass market boards are of SoC v2.0
move those USB PHY settings from ipq8065 (v3.0 SoC) dtsi to
ipq8064 v2.0 dtsi.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit d4b98c38c6)
ipq8065 is ipq8064 v3.0
> socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0, hw_plat_ver=65536
Include dtsi accordingly and remove the unneeded qcom-ipq8065-v1.0.dtsi
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit e16f9abf6b)
According to OEM bootlog entry mass market devices are ipq8064 SoC
v2.0:
> socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
I've checked C2600, EA8500 and VR2600v but couldn't find other
boards bootlog. I think it's safe to assume that other boards are
also v2.0. R7500 may be an exception because it was the first
device to hit the market.
So switch to v2.0 dtsi.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 067036e875)
According to QCA internal numbering there are 3 versions of
ipq8064/5 SoC:
ipq8064 v1.0 - probably ipq8064 evaluation boards only
ipq8064 v2.0 - probably ipq8064 mass market boards only
ipq8064 v3.0 - aka ipq8065, boards based on ipq8065.
Each next revision includes configuration differences from
previous revision and adds something new.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit adbdf78049)
It keeps failing (R7800) with the stack trace below
BUG: scheduling while atomic: kworker/0:1/26/0x00000002
(unwind_backtrace) from [<c02121d0>] (show_stack+0x10/0x14)
(show_stack) from [<c03932e4>] (dump_stack+0x7c/0x9c)
(dump_stack) from [<c0239b90>] (__schedule_bug+0x5c/0x80)
(__schedule_bug) from [<c05b7260>] (__schedule+0x50/0x3f4)
(__schedule) from [<c05b76a8>] (schedule+0xa4/0xd4)
(schedule) from [<c05ba430>] (schedule_hrtimeout_range_clock+0xc8/0x100)
(schedule_hrtimeout_range_clock) from [<c05ba480>]
(schedule_hrtimeout_range+0x18/0x20)
(schedule_hrtimeout_range) from [<c05b9f78>] (usleep_range+0x48/0x50)
(usleep_range) from [<c03f333c>] (__clk_hfpll_enable+0x44/0xd0)
(__clk_hfpll_enable) from [<c03f3474>] (clk_hfpll_set_rate+0xac/0xc4)
(clk_hfpll_set_rate) from [<c03ec390>] (clk_change_rate+0xf4/0x1fc)
(clk_change_rate) from [<c03ec510>] (clk_core_set_rate_nolock+0x78/0x94)
(clk_core_set_rate_nolock) from [<c03ec54c>] (clk_set_rate+0x20/0x30)
(clk_set_rate) from [<c0424168>] (dev_pm_opp_set_rate+0x190/0x26c)
(dev_pm_opp_set_rate) from [<c04a8548>] (set_target+0x40/0x108)
(set_target) from [<c04a4.140>] (__cpufreq_driver_target+0x3f4/0x488)
(__cpufreq_driver_target) from [<c04a7494>] (od_dbs_timer+0xcc/0x154)
(od_dbs_timer) from [<c04a7998>] (dbs_work_handler+0x2c/0x54)
(dbs_work_handler) from [<c02309e8>] (process_one_work+0x1c0/0x2f0)
(process_one_work) from [<c02319a8>] (worker_thread+0x2a4/0x404)
(worker_thread) from [<c0235944>] (kthread+0xd8/0xe8)
(kthread) from [<c020eef0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Marc Benoit <marcb62185@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit e40db2907e)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500v2.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit c3af761e47)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit c228bbe616)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 D7800.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Tathagata Das <tathagata@alumnux.com>
(cherry picked from commit 45b8a7c1a6)
The default image does not fit 2 MB anymore, expand kernel partition
to 3 MB.
Upgrading should work transparently via sysupgrade in both directions.
Another option would be to merge "kernel" and "rootfs" into a single
"firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the
sizes of the existing partitioning has been deemed safer in the absence
of an actual runtime test on an affected device; the maximum for rootfs
changes from 10.4 MB to 9.4 MB.
This change follows the example for the TP-Link Archer C2600, but has
not been runtime tested on a TP-Link Archer VR2600v.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Sebastian Quilitz <zeraphim@x-pantion.de>
(cherry picked from commit 0c967d92b3)
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.
Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.
Run-tested on TP-Link Archer C2600.
Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit b72b36653a)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This patch is based on a corresponding change by Pavel Kubelun
<be.dissent@gmail.com> and has been tested by Michael Yartys
<michael.yartys@protonmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit dc50694bd1)
Disable MSM8960, MSM8974 and APQ8084
- since these are different SoC's than IPQ806x
Removed unrequired serial configs
- since ipq806x uses SERIAL_MSM only
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 7ac6697fe2)
- Rebased the patches for 4.14
- Dropped spi-qup and 0027, 0028, 0029
clk patches since it's already included
in upstream.
Tested on IPQ AP148 Board:
1) NOR boot and NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 93dd2f7211)
This commit adds an EVA flashable image for the FRITZ!Box 4040.
The image contains the U-Boot with OpenWRT appended to it. This way we
remove the need to use UART for initial flashing.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 70e6ea319d)
This commit alters the TP-Link Archer C50v3 LED settings to use the phy
trigger instead of the netdev one. This way the WiFi status is displayed
even if the wifi interface name is altered.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ce91c85e01)
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 35d00d9a41)
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0
Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit a789c0f491)
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 67a3cdcbb0)
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit bdc2b58c4b)
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit a08b0d0c31)
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 978543a246)
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit ead26e9db6)
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit f928c338ad)
In commit 8b9cdebc9c ("arc770: mark as source-only") arc770 was marked
as source-only because of iproute2 compile issues.
With uClibc-ng version 1.0.30 issues with iproute2 were fixed.
Lets remove "source-only" for arc770 as soon as uClibc-ng version
will be updated to 1.0.30. Patch for uClibc-ng is here:
https://patchwork.ozlabs.org/patch/917547/
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
(cherry picked from commit a2418dba02)
Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.
This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ae8ff1c65c)
Copy and refresh patches and config from 4.9, no more work is need.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 3d69857ac1)
Disable CONFIG_EFI_VARS, since it suffers from sysfs limitation (no
support for variable longer than 1024 bytes).
kmod-fs-efivarfs is the replacement of this, which enables mounting
efivarfs file system and doesn't suffer from 1024 bytes limitation.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
(cherry picked from commit b0a51dab8c)
