TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.
Specifications
--------------
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.
Additional notes
----------------
MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.
*:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158
*:89 unused userconfig 0x0160
*:8A 5G not present in flash
This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
This adds a "factory" image for the aircube-isp devices. Note that the
firmware can't be uploaded without prior special preparation. For the
most recent instructions on how to do that, visit the OpenWRT wiki page
of the Ubiquiti airCube ISP for details:
https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp
Current procedure:
With the original firmware 2.5.0 it is possible to upload and execute a
script via the configuration. To do that download and unpack the
original configuration, adapt uhttpd config to execute another lua
handler (placed in the config directory) and pack and upload it again.
The lua handler can call a script that mounts an overlayfs and modifies
the "fwupdate.real" binary so that an unsigned image is accepted. The
overlayfs is necessary because a security system (called tomoyo) doesn't
allow binaries in other locations than /sbin/fwupdate.real (and maybe
some more) to access the flash when executed via network.
A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for
finding out how to patch the binary so that it accepts an unsigned
image.
The current step-by-step procedure is:
- Use a version 2.5.0 of the original firmware. This is important
because a binary file will be modified.
- Download a configuration.
- Unpack it (it's just a tar gz file without an ending).
- Add the following to uhttpd:
``````
config 'uhttpd' 'other'
list listen_http 0.0.0.0:8080
list listen_http [::]:8080
option 'home' '/tmp/persistent/config/patch/www'
option lua_prefix '/lua'
option lua_handler '/tmp/persistent/config/patch/handler.lua'
``````
- Create a `patch` subfolder.
- Create a `patch/www` subfolder.
- Create a `patch/handler.lua` with the following content:
``````
function handle_request(env)
uhttpd.send("Status: 200 OK\r\n")
uhttpd.send("Content-Type: text/plain\r\n\r\n")
local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1"
local proc = assert(io.popen(command))
for line in proc:lines() do
uhttpd.send(line.."\r\n")
end
proc:close()
end
``````
- Create a `patch/patch.sh` with the following content:
``````
#!/bin/sh -x
set -e
set -u
set -x
UBNTBOX_PATCHED="/tmp/fwupdate.real"
MD5FILE="/tmp/patchmd5"
cat <<EOF > ${MD5FILE}
c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real
EOF
# check md5 of files that will be patched
if ! md5sum -c ${MD5FILE}
then
echo "******** Error when checking files. Refuse to do anything. ********"
exit 0
fi
# prepare some overlay functionality
LOWERDIR="/tmp/lower_root"
mkdir -p ${LOWERDIR}
mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR}
overlay_some_path()
{
PATH_TO_OVERLAY=$1
ALIAS=$2
UPPERDIR="/tmp/over_${ALIAS}"
WORKDIR="/tmp/over_${ALIAS}_work"
mkdir -p ${UPPERDIR}
mkdir -p ${WORKDIR}
mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY}
}
# patch the ubntbox binary.
overlay_some_path "/sbin" "sbin"
echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598
echo "******** Done ********"
``````
- Repack the configuration.
- Upload it via the normal web interface.
- Wait about a minute. The webserver should restart.
- Now there is a second web server at port 8080 which can call the lua
script. Visit the page with a web browser. Link is for example
http://192.168.1.1:8080/lua
- You should see the output of the script with a "*** Done ***" at the
end. Note that the patches are not permanent. If you restart the
router you have to re-visit the link (but not re-upload the config).
- Now you can upload an unsigned binary via the normal web interface.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Its way more trouble to update this to a newer version of qemu than it
is to backport the two additional features we need.
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
This replaces tabs by spaces when preceding an equal sign. This improves
consistency in the file and makes the indent look correct on all platforms.
While at it, also fix one case of inconsistent leading spaces.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to the SourceForge page, the project is migrating to GitHub.
Thus, change the source of the package to GitHub.
Signed-off-by: David Bauer <mail@david-bauer.net>
"2.0" instead of "2.00" is sufficient and more in line with the
other definitions.
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[commit message/title adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 2.4GHz N based AP
Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
common DTSI
- move ð0 to parent DTSI
- fix several leading spaces, added/removed newlines
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 43365ca662 ("Do not use $(V) - force AM_V=1") as
it breaks verbose output in automake packages, deviating from the
upstream and expected behaviour.
As you can see, neither make command outputs the expected verbose
compile command lines:
```
$ make package/mtd-utils/{clean,compile} V=sc
...
CCLD lsmtd
CC nand-utils/nanddump.o
CCLD nanddump
...
```
```
$ make -C build_dir/target*/mtd-utils-2.1.1 clean
...
$ make -C build_dir/target*/mtd-utils-2.1.1 V=1
...
CC lib/libmtd.o
CC lib/libfec.o
CC lib/common.o
CC lib/libcrc32.o
```
The original reason for this commit was some packages failing to build
if V is set to something other than 0 or 1. See the discussion in PR
https://github.com/openwrt/openwrt/pull/2481 for how to fix this in the
package Makefile.
Ref: PR#2481
Acked-by: Mirko Vogt <mirko-openwrt@nanl.de>
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[commit title/description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344
The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254
The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"$(STAGING_DIR)/include" was carried over from buildroot-ng to OpenWrt
in commit 60c1f0f64d. buildroot has
dropped this directory a long time ago.
In OpenWrt the directory is still created by the PrepareStaging macro
and is part of the default TARGET_CPPFLAGS. But nothing at all installs
headers into this directory, nor should anything be installed under this
path.
Removing this directory from TARGET_CPPFLAGS will cut down the log noise
a bit. Not only will CPPFLAGS be shorter, there will be less warnings
set off by "-Wmissing-include-dirs" (or even failures when paired with
"-Werror"). After all the directory does not even _exist_ in the SDKs,
which are used on the build bots when building packages (see [1] and
[2]).
make[8]: Entering directory '/builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/libmbim-1.20.0/src/common'
CC libmbim_common_la-mbim-common.lo
cc1: error: /builder/shared-workdir/build/sdk/staging_dir/target-aarch64_generic_musl/include: No such file or directory [-Werror=missing-include-dirs]
cc1: all warnings being treated as errors
[1] https://github.com/openwrt/packages/issues/10377
[2] https://github.com/openwrt/packages/pull/10378
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Rosen Penev <rosenp@gmail.com>
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch removes scons host build tool, as commit 7087efd72a8d
("scons: move host build tool to a proper place") in the packages feed
has moved scons into the new home.
There are currently no packages in the master tree which would need
scons, yet scons is build always as part of host tools, just in order to
satisfy host build dependency of few packages in the packages feeds.
Ref: https://github.com/openwrt/packages/pull/9584
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This updates the U-Boot which provides the host tools like mkimage to
version 2019.07.
The patches were cleaned up and it was checked if this still compiles
on Linux and FreeBSD.
CONFIG_FIT_SIGNATURE_MAX_SIZE is set to the default value.
The patch for libressl was merged upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This has two improvements over the current version. An autotools fix and
application of the wrt350v2 patch.
Cleaned up Makefile as a result of makefiles being fixed.
Note that this package is not really used as it depends on orion, which is
classified as broken.
This is the last package that uses svn in the tree.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When libelf from tools/ is used for building the kernel, compilation
aborts due to access to undefined defines since Kbuild adds -Wundef
to the compiler flags.
Patch the header files to use `#if defined(...)` instead of `#if ...`
to prevent such issues.
Ref: https://github.com/NixOS/nixpkgs/issues/59929
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Install the pkg-config definition for libelf in order to allow the
kernel build process discover it later on.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update CMake to 3.15.1
Refresh patches
Remove inofficial fossies.org and replace with GitHub (link on official site)
Remove 150-C-feature-checks-Match-warnings-more-strictly.patch as it's
a no longer needed backport from upstream.
Disable ccache if GCC is 4.8, 4.9 or 5.X to avoid build failures.
Reference: https://github.com/openwrt/openwrt/pull/1929
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update make-ext4fs to commit eebda1d55d9701ace2700d7ae461697fadf52d1f
git log --pretty=oneline --abbrev-commit 484903e4..eebda1d5
eebda1d make_ext4: Add strict prototypes.
bb9cf91 make_ext4fs: Remove off64_t in favor of standard off_t
Created with the help of the make-package-update-commit.sh script.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Update e2fsprogs to 1.45.3
Remove OpenBSD patch
Remove Darwin patch, neither macports or brew patches these files
Add patch to avoid crond detection on host OS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
GNU patch through 2.7.6 is vulnerable to OS shell command injection that
can be exploited by opening a crafted patch file that contains an ed style
diff payload with shell metacharacters. The ed editor does not need to be
present on the vulnerable system. This is different from CVE-2018-1000156.
https://nvd.nist.gov/vuln/detail/CVE-2019-13638
Signed-off-by: Russell Senior <russell@personaltelco.net>
This version bump includes a bunch of fixes and improvements, which
should fix gpsd build breakage in the package feeds.
Ref: https://github.com/SCons/scons/blob/master/src/CHANGES.txt
Signed-off-by: Russell Senior <russell@personaltelco.net>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This seems to be identical to CPE210 v1 despite having removable
antennas.
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is a preparation for ath79 support of the CPE210/CPE510 v1.
Kernel size is chosen equal to the latest update for CPE610 v1.
This also updates the partition size in ar71xx target, so code
remains consistent if someone looks up the device. Since CPE210,
CPE510, WBS210 and WBS510 (all v1) share the same partition
layout definition, and are on deprecated target anyway, this
changes them all at once.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes following issue reported by Coverity scan:
*** CID 1452085: Security best practices violations (TOCTOU)
/tools/firmware-utils/src/uimage_padhdr.c: 100 in main()
94
95 if (!infname || !outfname) {
96 usage(argv[0]);
97 exit(1);
98 }
99
>>> CID 1452085: Security best practices violations (TOCTOU)
>>> Calling function "stat" to perform check on "infname".
100 if (stat(infname, &statbuf) < 0) {
Fixes: a1c6a316d2 ("ramips: add support for Fon FON2601")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In GNU patch through 2.7.6, the following of symlinks is mishandled in
certain cases other than input files. This affects inp.c and util.c.
https://nvd.nist.gov/vuln/detail/CVE-2019-13636
Signed-off-by: Russell Senior <russell@personaltelco.net>
Since the switch to Python 3 build fails if CONFIG_USE_MKLIBS is set
("Strip unnecessary functions from libraries" in menuconfig) as
mklibs hasn't been converted to run on Python 3.
* update to most recent upstream version which brings some
reproducibility fixes
* converted to Python 3 using 2to3
* fixed mixed tab/spaces indentation
* fixed use of string.* functions
* some more minor fixes to make Python 3 happy
Fixes commit 19938c8de7 ("build: switch to Python 3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build tested on ath79 with following packages from packages feed which
build depends on scons. None of them build anymore as it seems, that the
SConscripts are written for Python2.
* packages/net/iotivity (KO, doesn't build even with latest 1.3.1 release)
SyntaxError: invalid syntax
File "/openwrt/build_dir/target-mips_24kc_musl/iotivity-1.2.1/build_common/SConscript", line 40
print "\nError: Current system (%s) isn't supported\n" % host
LookupError: unknown encoding: string_escape:
File "/home/petr/testing/openwrt/build_dir/target-mips_24kc_musl/iotivity-1.3.1/SConstruct", line 28:
SConscript('build_common/SConscript')
* packages/net/smartsnmpd (KO, seems dead, no commit since 2015):
SyntaxError: Missing parentheses in call to 'print'
File "/openwrt/build_dir/target-mips_24kc_musl/smartsnmpd-2014-08-13/SConstruct", line 156
print "Can't find liblua or liblua5.1!"
* packages/utils/gpsd (KO, doesn't build even with latest 3.18.1 release):
AttributeError: 'list' object has no attribute 'keys':
File "/openwrt/build_dir/target-mips_24kc_musl/gpsd-3.18.1/SConstruct", line 1758:
all_manpages = list(base_manpages.keys()) + list(python_manpages.keys())
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Making all in tests
depbase=`echo handshake_table.o | sed 's|[^/]*$|.deps/&|;s|\.o$||'`;\
gcc -DPACKAGE_NAME=\"libressl\" -DPACKAGE_TARNAME=\"libressl\" -DPACKAGE_VERSION=\"2.9.2\" -DPACKAGE_STRING=\"libressl\ 2.9.2\" -DPACKAGE_BUGREPORT=\"\" -DPACKAGE_URL=\"\" -DPACKAGE=\"libressl\" -DVERSION=\"2.9.2\" -DSTDC_HEADERS=1 -DHAVE_SYS_TYPES_H=1 -DHAVE_SYS_STAT_H=1 -DHAVE_STDLIB_H=1 -DHAVE_STRING_H=1 -DHAVE_MEMORY_H=1 -DHAVE_STRINGS_H=1 -DHAVE_INTTYPES_H=1 -DHAVE_STDINT_H=1 -DHAVE_UNISTD_H=1 -DHAVE_DLFCN_H=1 -DLT_OBJDIR=\".libs/\" -DHAVE_SYMLINK=1 -DHAVE_ERR_H=1 -DHAVE_READPASSPHRASE_H=1 -DHAVE_ASPRINTF=1 -DHAVE_MEMMEM=1 -DHAVE_READPASSPHRASE=1 -DHAVE_STRLCAT=1 -DHAVE_STRLCPY=1 -DHAVE_STRNDUP=1 -DHAVE_STRNLEN=1 -DHAVE_STRSEP=1 -DHAVE_TIMEGM=1 -DHAVE_GETPROGNAME=1 -DHAVE_SYSLOG=1 -DHAVE_POLL=1 -DHAVE_SOCKETPAIR=1 -DHAVE_ARC4RANDOM=1 -DHAVE_ARC4RANDOM_BUF=1 -DHAVE_ARC4RANDOM_UNIFORM=1 -DHAVE_TIMINGSAFE_BCMP=1 -DHAVE_CLOCK_GETTIME=1 -DHAVE_VA_COPY=1 -DHAVE___VA_COPY=1 -DSIZEOF_TIME_T=8 -I. -I../include -I../include/compat -DLIBRESSL_INTERNAL -D__BEGIN_HIDDEN_DECLS= -D__END_HIDDEN_DECLS= -I ../crypto/modes -I ../crypto/asn1 -I ../ssl -I ../tls -I ../apps/openssl -I ../apps/openssl/compat -D_PATH_SSL_CA_FILE=\"../apps/openssl/cert.pem\" -I/Users/kevin/wrt/staging_dir/host/include -D__STRICT_ALIGNMENT -O2 -I/Users/kevin/wrt/staging_dir/host/include -fpic -Wall -std=gnu99 -fno-strict-aliasing -fno-strict-overflow -D_FORTIFY_SOURCE=2 -fstack-protector-strong -Qunused-arguments -Wno-pointer-sign -MT handshake_table.o -MD -MP -MF $depbase.Tpo -c -o handshake_table.o handshake_table.c &&\
mv -f $depbase.Tpo $depbase.Po
make[4]: *** No rule to make target `/Users/kevin/wrt/build_dir/host/libressl-2.9.2/crypto/.libs/libcrypto_la-cpuid-macosx-x86_64.o', needed by `handshake_table'. Stop.
make[3]: *** [all-recursive] Error 1
A similar error & clues from
e783d60473
"
LibreSSL 2.9.1 now has a test that requires libtls.a, however, when building a
shared library only build, the --disable-static flag is passed to libressl,
which prevents the building of libtls.a.
With libtls.a not being built, the following error occurs:
libressl-2.9.1/tls/.libs/libtls.a', needed by 'handshake_table'. Stop.
There are three options to fix this:
1) Stick with autotools, and provide a patch that removes building anything in
the tests folder.
2) Pass --enable-static to LIBRESSL_CONF_OPTS
3) Change the package type to cmake, as a cmake build does not have this issue."
It appears we cannot change to cmake because cmake has a dependency on
an ssl library.
Take option 1 and do not build the tests.
Also take the opportunity to remove man page building as well.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes following errors:
src/mkfwimage.c:279:8: error: format specifies type 'long' but the argument has type 'off_t' (aka 'long long') [-Werror,-Wformat]
d->stats.st_size,
^~~~~~~~~~~~~~~~
src/mkfwimage.c:280:8: error: format specifies type 'long' but the argument has type 'long long' [-Werror,-Wformat]
d->partition_length - d->stats.st_size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/mkfwimage.c:378:6: error: format specifies type 'unsigned long' but the argument has type 'long long' [-Werror,-Wformat]
d->stats.st_size - d->partition_length);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
src/mkfwimage.c:276:8: error: format '%lld' expects argument of type 'long long int', but argument 4 has type '__off_t' {aka 'const long int'} [-Werror=format=]
src/fw.h:71:36: error: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type '__off_t' {aka 'long int'} [-Werror=format=]
inlined from 'main' at src/mkfwimage.c:543:12:
/string_fortified.h:106:10: error: '__builtin_strncpy' output truncated before terminating nul copying 4 bytes from a string of the same length [-Werror=stringop-truncation]
inlined from 'write_part' at src/mkfwimage.c:235:2,
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 16 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:477:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 256 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:496:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 4096 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:481:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 4096 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:485:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 16 equals destination size [-Werror=stringop-truncation]
Runtested on ath79 and UBNT Bullet M XW.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fix 4 errors reported by gcc 9
3 mismatched format type errors
1 unused variable error
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
While looking at the ath25 build breakage of 19.07 images today I've
encountered following error:
mkfwimage -B XS5 -v [...] ath25-ubnt5-squashfs-sysupgrade.bin.new
ERROR: Failed creating firmware layout description - error code: -2
Which is barely human readable and needs poking into the source code, so
this patch makes the error more verbose and usable by mere mortals.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Let's enforce additional automatic checks enforced by the compiler in
order to catch possible errors during compilation.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, and 4 green LEDs
- 1 10/100Mbps Shielded Ethernet Port (Passive PoE in)
- Built-in 13dBi 2x2 dual-polarized directional MIMO antenna
- Adjustable transmission power from 0 to 23dBm/200mw
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
Update gengetopt to 2.23
Remove 100-dependency_fix.patch, fixed upstream
Rework no tests and docs patch
Fix typo in copyright section
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Increase the Kernel partition to address the issue discussed here
https://forum.openwrt.org/t/cpe610-v1-sysupgrade-bin-missing-too-big/39637/5
Switch Back to the okli Loader to support increased partition size
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [add <> for e-mail]
TP-Link CPE610-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, WLAN5G green LEDs
- 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
The first version of this script allowed just 4Mb factory images.
With this patch is possible to set the maximum size of the payload.
For an 8Mb flash, the corresponding maxsize is:
8 * 1024 * 1024 - 5 * 64 * 1024 = 8388608 - 327680 = 8060928
If the -m argument is not set, the default maximum size will be
used for backward compatibility.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
This reverts commit 0111b86f1d as it
breaks on Linux distributions without ed support
./fix-libmath_h: line 1: ed: command not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This commit adds the partition layout used by the TP-Link Archer D50
and probably by the TP-Link Archer D7 to mktplinkfw2.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
This patch enable gnu99 mode for the nec-enc utility which
fixes the following build-breaking errors on some older
architectures.
nec-enc.c: In function ‘xor_data’:
nec-enc.c:34:2: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < len; i++) {
^~~
nec-enc.c:34:2: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
nec-enc.c: In function ‘main’:
nec-enc.c:101:3: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < n; i++) {
^~~
Spotted-By: Buildbot
Fixes: fac27643f0 ("firmware-utils: add nec-enc")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
nec-enc provides firmware encoding/decoding with model specific key
for NEC devices.
known devices:
- Aterm WF1200CR
- Aterm WG1200CR
- Aterm WG2600HS
usage:
nec-enc -i infile -o outfile -k key
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch fixes, marked usage as noreturn, added static function,
moved buf* from stack to the global data segment]
I made a similar change to this here:
https://github.com/openwrt/packages/pull/8159
However, it turns out this did not fix the problem as the problem has to
do with tools/xz and not the xz package. The error is the same and causes
linking errors as can be seen above.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This provides board configuraion tables for various Tegra boards needed
by cbootimage tool to create flashable bootloader images.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tegra BCT and bootable flash image generator/compiler
>From documentation:
This project provides a tool which compiles BCT (Boot Configuration
Table) images to place into the boot flash of a Tegra-based device.
The tool will either:
a) Compile a textual representation of a BCT into a binary image.
b) Generate an entire boot image from a previously compiled BCT and a
bootloader binary.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is also helpful to add support in ath79.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The cmake bump to 3.14.0 breaks build on all targets. Revert it for now.
This reverts commit a3446257a8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update CMake to 3.14.0
Refresh patches
Remove inofficial fossies.org and replace with GitHub (link on official site)
Remote 150-C-feature-checks-Match-warnings-more-strictly.patch as it's
a no longer needed backport from upstream.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Require the word "warning" to appear at the start of a line, after
whitespace, or after a `:`. This is the same that CTest launchers use
to match warnings. It avoids matching "warning" inside file paths.
Fixed in cmake 3.14.0.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Fixes timeouts with trying to access the FTP site.
Also remove mirror2.openwrt.org, which does not keep current tarballs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gnu date is present in our staging_dir which means squashfskit will fail
to build. Prevent also a race condition if coreutils is build after
squashfskit.
To prevent a race condition, depend on coreutils.
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.
This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.
We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The firmware on the D-Link DNS-313 NAS require two blank
partitions before the boot partition. Support this if
explicitly requested with a "-n" flag.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Broken out from original patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update mpfr to 4.0.2
Use official site as last resort
Force thread-safety functionality
Refresh patches
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Fix for factory image generation, so that stock firmware will accept the
openwrt image.
Ref: https://forum.openwrt.org/t/support-for-tp-link-archer-c2-v3/15617/17
Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reword commit message, use correct order for conditions,
trim trailing whitespace]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
