mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-19 05:38:00 +00:00
9b90dc05f5
This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> |
||
|---|---|---|
| .. | ||
| autoconf | ||
| automake | ||
| b43-tools | ||
| bc | ||
| bison | ||
| cbootimage | ||
| cbootimage-configs | ||
| ccache | ||
| cmake | ||
| coreutils | ||
| dosfstools | ||
| e2fsprogs | ||
| elftosb | ||
| expat | ||
| findutils | ||
| firmware-utils | ||
| flex | ||
| flock | ||
| genext2fs | ||
| gengetopt | ||
| gmp | ||
| include | ||
| isl | ||
| kernel2minor | ||
| libelf | ||
| libressl | ||
| libtool | ||
| lzma | ||
| lzma-old | ||
| m4 | ||
| make-ext4fs | ||
| missing-macros | ||
| mkimage | ||
| mklibs | ||
| mm-macros | ||
| mpc | ||
| mpfr | ||
| mtd-utils | ||
| mtools | ||
| padjffs2 | ||
| patch | ||
| patch-image | ||
| patchelf | ||
| pkg-config | ||
| qemu | ||
| quilt | ||
| sdimage | ||
| sed | ||
| sparse | ||
| squashfs | ||
| squashfskit4 | ||
| sstrip | ||
| tar | ||
| upslug2 | ||
| wrt350nv2-builder | ||
| xz | ||
| zip | ||
| zlib | ||
| Makefile | ||