Patch picked from commit 82618062cf
This enables 4B opcodes for MX25L25635F, to fix the reboot crash
issue (FS#1120) At least 3 devices are using this flash
- GeHua GHL-R-001
- Youku YK1
- Newifi D1
Now the MX25L25635F can be correctly detected without breaking MX25L25635E
[ 3.034324] spi-mt7621 1e000b00.spi: sys_freq: 220000000
[ 3.045962] m25p80 spi0.0: mx25l25635f (32768 Kbytes)
[ 3.056098] 4 fixed-partitions partitions found on MTD device spi0.0
[ 3.068748] Creating 4 MTD partitions on "spi0.0":
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added deprecation notice]
CPU: FSL P1020 (2x 800MHz E500 PPC)
RAM: 1GB DDR3
FLASH: 256MiB NAND
WiFi: 2x Atheros AR9382 2x2:2 abgn
ETH: 2x BCM54616S - 1x BCM53128 8-port switch
LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN: 1x RESET
Installation
------------
1. Download initrams kernel image, dtb binary and sysupgrade image.
2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".
3. Place dtb binary into tftp root directory. Rename to "panda.fdt".
4. Start tftp server on 192.168.100.8/24.
5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.
6. SSH into the device and remove the factory partitions.
> ubirmvol /dev/ubi0 --name=kernel1
> ubirmvol /dev/ubi0 --name=rootfs1
> ubirmvol /dev/ubi0 --name=devicetree1
You will have around 60 MiB of free space with that.
You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.
7. Modify the U-Boot bootcmd to allow for booting OpenWRT
> fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
&& bootm 0x1000000"
> fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
ubi.mtd=3,2048"
> fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"
8. Transfer the sysupgrade image via scp into the /tmp directory.
9. Upgrade the device
> sysupgrade -n /tmp/<imagename>
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit removes the target-specific diag.sh script. This way, the
generic one is used for the target, which uses DT-aliases to specify the
LEDs used.
This way, we are also able to use different LEDs to indicate different
states. We use green status LEDs for indicating boot and a running
system. Where possible, the red status LED is used to indicate failsafe
mode and a running upgrade.
Signed-off-by: David Bauer <mail@david-bauer.net>
The unit address should be wifi@1,0 since the device is located
at 0000:01:00.0.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With 6409b159e8 ("gemini: switch to 4.14") the EOF marker were dropped
from the rootfs images. Without the marker the rootfs_data partition
can't be created and it isn't possible to permanently store any
configuration changes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Replace the data placerholder in ImageInfo-itian_sq201 in a reproducible
way.
The code for the replace was accidentality dropped in 5bac623895
("gemini: unify and fix ib-nas4220b and sq201 image creation")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Support for the Teltonika RUT1xx was added with the switch to kernel
4.4. Hidding such changes in a kernel switch commit is the wrong way and
the support for the Teltonika RUT1xx is pretty much incomplete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
They were dropped with 6409b159e8 ("gemini: switch to 4.14") without
any explaination.
The image generation is disabled for now as it would break the build for
the target. The mkfwimage2 call need to be adjusted to reflect the real
size of kernel and rootfs. Nevertheless, add the required code to give
interested parties a chance to fix the remaining issues.
The dts would need to use the ecoscentric,redboot-fis-partitions
partition parser to get the correct partition offsets and size. It's
expected that the OEM firmware adjusts the on flash partition table with
the values defined in the image header.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use an output image filename based on the compatible string from the dts
files. This way it is way easier to get for which board an image is
intended.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The root filesystem is already part of the factory image and most likely
not required at all.
The same applies to the kernel images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There is no support for sysupgrade in gemini, hence all images are only
suitable for an installation via bootloader or oem firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
For temporary directories <imagename>.tmp is a common pattern in image
build code across the tree. Use it for the nas4220b/sq201 recipe as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Create files in temporary directories within the build directory
instead manipulating files in the (final) output directory.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the missing PROFILES all images are build, regardless of the
selected (or currently processed in case of a multi profile build).
Because of the race condition builds with eight parallel jobs fail,
which can be seen on the build bots as well.
Add the PROFILES variable for now, till the root cause is identified.
Signed-off-by: Mathias Kresin <dev@kresin.me>
When using Image Builder and building image for Cortex A53 or
A72 subtargets, it'll fail with following message:
Collected errors:
* opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8864.
* opkg_install_cmd: Cannot install package mwlwifi-firmware-88w8964.
make[2]: *** [Makefile:153: package_install] Error 255
make[1]: *** [Makefile:114: _call_image] Error 2
This is beacuse both packages are available only for Cortex A9 subtarget
and are included in PACKAGES array in default profile. Instead patching
this, let's remove profiles completely, since all necessary packages are
specified in DEVICE_PACKAGES array for each device.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This removes the misplaced UCI-network configuration for the MR33. The
LAN port is set in 01_leds while it is already correctly defined in
02_network.
This was most likely an oversight as no network configuration belongs
into 01_leds.
Signed-off-by: David Bauer <mail@david-bauer.net>
Enable support for 2nd USB port, which is available on Fritz!Box 7320
and 7330. It was run-tested on 7320 and 7330 as well.
Signed-off-by: Robert Resch <openwrt@webnmail.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit changes the model string and device title of all AVM boards
to fit the naming of the manufacturer.
Drop all provider-specific titles as they are re-used for every device
generation by 1&1. The original AVM model name is printed on the bottom
of every devices.
Exception applies for boards which are only supported by a specific
sub-revision.
Signed-off-by: David Bauer <mail@david-bauer.net>
Change the "status" LED to proper GPIO 12 and "red" naming.
Remove GPIO 2 from definition as a USB LED.
GPIO 2 is used to control power to the USB socket, not an LED.
As such, PWM on the line or typical LED triggers are inappropriate.
Users who wish to control the USB power for custom applications
can manipulate the GPIO through code, or for example, export it
through /sys/class/gpio/export.
Runtime-tested: GL.iNet AR300M-Lite
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
A missing upstream stable backport leads to the following build error:
CC drivers/mmc/host/sdhci-msm.o
drivers/mmc/host/sdhci-msm.c:1158:3: error: 'const struct sdhci_ops' has no member named 'write_w'
.write_w = sdhci_msm_write_w,
^~~~~~~
drivers/mmc/host/sdhci-msm.c:1158:13: warning: excess elements in struct initializer
.write_w = sdhci_msm_write_w,
^~~~~~~~~~~~~~~~~
drivers/mmc/host/sdhci-msm.c:1158:13: note: (near initialization for 'sdhci_msm_ops')
scripts/Makefile.build:326: recipe for target 'drivers/mmc/host/sdhci-msm.o' failed
Solve the issue by backporting commit
99d570da30 ("mmc: Kconfig: Enable CONFIG_MMC_SDHCI_IO_ACCESSORS")
from linux-stable.
Ref: 528508ae8b (commitcomment-32049231)
Fixes: 528508ae8b ("kernel: bump 4.14 to 4.14.95")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Both Build/sq201-images and Build/nas4220b-images scripts
are very similar. This patch unifies both methods at the
cost of renaming the produced sysupgrade file names, but
with the benifit of creating better reproducible files.
The patch also fixes a race in parallel builds in which case
the ImageInfo of one device could end up in both sysupgrade
files.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, IMAGE_NAME is expanded at declaration time
and this causes strange filename in the builder's logs:
|cp: cannot stat '[...]/openwrt-gemini-dlink-dns-313-.': No such file or directory
|cp: cannot stat '[...]/openwrt-gemini-nas4220b-.': No such file or directory
|[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch replaces the current hack with a better
version of the RFC patch has been accepted upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- remove stray #address-cells / #size-cells
- fix partition unit-addresses in wd-mybooklive.dts
- remove index from MBL's gpio node name
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds the boot-part feature which enables the brcm2708
target move from the custom boot partition size config option to
the generic CONFIG_TARGET_KERNEL_PARTSIZE.
Note:
For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value
can cause sysupgrade to repartition the device!
Make sure to have a backup in this case.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Current code directly writes the FOE entry to hash_val+1 position
when hash collision occurs. However, it is found that this behavior
will cause the cache and the hardware FOE table to be inconsistent.
For example, there are three flows, and their hashed values are all
equal to 100. The first flow is written to the position of 100. The
second flow is written to the position of 100+1. Then, the logic of
the current code will also write the third flow to 100+1.
At this time, the cache has flow 1 and 2; and the hardware FOE table
has flow 1 and 3, where these two parts store different contents.
So it is necessary to check whether the hash_val+1 is also occupied
before writing. If hash_val+1 is also occupied, we won’t bind th
third flow to the FOE table.
Addition to that, we also cancel the processing of foe_entry removal
because the hardware has auto age-out ability. The hardware will
periodically iterate through the FOE table to find out the time-out
entry and set it as INVALID.
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
LAN ports 1 and 4 and 2 and 3 are interchanged. Fix this in 02_network
so the ports show up in the correct order in luci.
The correct ucidef_add_switch line is already present. This commit moves
the blocks around to keep alphabetical order.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.
This fix preserves port mirroring flags during apply.
Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
The swconfig load operation always triggers 'apply' function which in
this driver currently clears port mirroring flags effectively undoing
port mirroring configuration.
Signed-off-by: Milan Krstic <milan.krstic@gmail.com>
Backport upstream patch:
Commit 65cab850f0ee ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.
Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0ee ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch applies cleanly, so it doesn't cause errors while rebasing
patches. It results in redifinition of inode_still_linked, causing build
to fail when ubifs is enabled. Drop the patch.
Fixes: a37098a2d0 ("kernel: bump 4.19 to 4.19.16")
Reported-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This adds supprot for kernel 4.19 to the sunxi target. The patches and
the configuration were copied from the kernel 4.14 patches folder and
adapted for kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To make it easier to support multiple kernel versions in parallel also
copy the sub target specific kernel configurations into kernel specific
files.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the device tree file the higher offsets of the reset controller are
not used, so this patch supporting higher bits is not needed.
The sunxi architecture switched to the simple reset controller with
kernel 4.19 and then this patch does not apply any more.
The sunxi target in OpenWrt is very close to mainline, so if the device
tree files from the mainline Linux kernel need this the mainline kernel
will get support for this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This configuration option was added in kernel 4.15 and is missing in the
kernel 4.19 configuration.
Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds a kernel configuration file for kernel 4.19 on malta.
CONFIG_POWER_RESET_PIIX4_POWEROFF and CONFIG_POWER_RESET_SYSCON were
activated because malta now uses this driver for reboot.
CONFIG_BLK_DEV_SR was also added because it was also added to the kernel
default configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Many MIPS CPUs have optional CPU features which are not activates for
all CPU cores. Print the CPU options which are implemented in the core
in /proc/cpuinfo. This makes it possible to see what features are
supported and which are not supported. This should cover all standard
MIPS extensions, before it only printed information about the main MIPS
ASEs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes two build problems introduced with the recently added new
kernel module package.
Fixes: ed2839ac41 ("kernel/modules: add kmod-pmbus-zl6100 module")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
========
CPU: Freescale P1010 PowerPC
RAM: 128M DDR3
NAND: 128MiB
ETH: RTL8211F SGMII PHY
RTL8367B 5-port RGMII switch
(not connected to SoC - unmanaged)
WiFi: SparkLan WPEA-121N
- Atheros AR9382 2T2R abgn
USB: 1x USB 2.0
LED: System, Router, Internet, Tunnel controllable
LAN1-4, WAN, Power non-controllable
BTN: None
Installation
============
1. Power on the device while attached to the Console port.
2. Halt the U-Boot by pressing Enter when prompted.
3. Set the correct bootcmd for booting OpenWRT:
> setenv bootargs_owrt "setenv bootargs console=ttyS0,115200"
> setenv bootcmd "run bootargs_owrt;
nand read 0x1000000 0x300000 0x800000;
bootm 0x1000000;"
> saveenv
5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a
TFTP server root-directory served on 192.168.1.2/24. Connect your
computer to one of the LAN-ports.
4. Boot OpenWRT initramfs image with
> run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin;
bootm 0x1000000;
6. (Optional)
Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case
you ever want to go back to the vendor firmware.
7. Create Ubi Volume on mtd4 by executing
> ubiformat /dev/mtd4 -y
8. Transfer OpenWRT sysupgrade image to the device via SCP and install it
with
> sysupgrade -n <openwrt-image-file>
Back to Stock
=============
If you want to go back to the stock firmware, here is the bootcmd of the
vendor firmware:
> setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5;
nand read 0xc00000 0x00300000 0x100000;
nand read 0x1000000 0x00400000 0x00800000;
bootm 0x1000000 - 0xc00000
Set it via 'setenv' from the U-Boot shell and don't forget to save it
using 'saveenv'!
After this, boot the OpenWRT initramfs image just like you would for
installation. Write back the three vendor partitions using mtd. Reboot
the device afterwards.
Signed-off-by: David Bauer <mail@david-bauer.net>
[refresh and reorder patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Initramfs image isn't required for this device and regular
initramfs generation isn't work properly. It create not working
binaries.
This patch disable initramfs image for TL-WDR4900.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds the kmod packaging for the Intersil / Zilker Labs
ZL6100 and compatible digital DC-DC controllers as well as the
core kernel module for the Power Management Bus.
Add:
kmod-pmbus-core
kmod-pmbus-zl6100
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This adds initial support for kernel 4.19 to the x86 target.
The patches and the kernel configurations were copied from kernel 4.14
and then refreshed.
The legacy and the genode target will not support PAE any more because
they use a CPU type which does not support PAE, the generic sub target
still supports PAE.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This refreshes the kernel configuration for kernel 4.14.
First this was run for the legacy target:
make kernel_oldconfig
Then for all targets including the legacy target this was run:
make kernel_oldconfig CONFIG_TARGET=subtarget
The option CONFIG_104_QUAD_8 was added to the generic configuration
because it would have been automatically removed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes it possible to use different sub target configurations for
kernel 4.19 for example.
To support kernel 4.9 and kernel 4.14 with the same configuration file
already needed some extra work this will not be needed for kernel 4.19
any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's needed to:
1) Fix GPIOLIB_IRQCHIP as in 4.19 there is no bcma revert anymore
2) Fix /sys/devices/
3) Fix dma_zalloc_coherent() regression
It still needs a bcma change that will follow later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
upstream commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
reimplemented cns3xxx_pci_read_config() using pci_generic_config_read32(),
which preserved the property of only doing 32-bit reads.
It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.
Due to:
- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended
It makes perfectly sense to also swap 32 bit reading in favor of actual size.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Sometimes the tuples might be hashed to the same FOE entry.
When this hash collision problem occurs, some of the
connections will not be bound and consequently the CPU
idle rate cannot reach 100%. Therefore, two-way hashing
is adopted to alleviate this problem.
Signed-off-by: HsiuWen Yen <y.hsiuwen@gmail.com>
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.
Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.
This fixes eva-image generation using the OpenWRT image-builder.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch syncs the 4.14 kernel config to the
current generic configuration.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
This patch syncs the 4.19 kernel config since the
KERNEL_STACKPROTECTOR and compiler options are
now part of the 4.19 generic config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Robert Marko reported an issue with the current imagebuilder images:
"Imagebuilder includes the new kmod-usb-dwc3-qcom USB driver
package by default even on 4.14. [...] the current state imagebuilder
can't build images under 4.14 at all as the kmod-usb-dwc3-qcom does
not exist in it so it throws and error and exits."
This patch reverts the Makefile to just kmod-usb-dwc3-of-simple and
once the switch to 4.19 is done. It also removes the
kmod-usb-phy-qcom-dwc3 as they only contain the usb-phy drivers for
the ipq806x generation.
Dynamic switching based on the KERNEL_PATCHVER is possible by using:
$(if $(filter 4.14,$(KERNEL_PATCHVER)),kmod-usb-dwc3-of-simple,kmod-usb-dwc3-qcom)
though it
Fixes: 13321fa142 ("ipq40xx: Use kmod-usb-dwc3-qcom by default")
Fixes: 6e58fb2c33 ("ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom")
Reported-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The name for the artifact should have been apollo3g.dtb
and not kernel.dtb.
Fixes: 908bdbfce9f9 ("apm821xx: utilize build ARTIFACTs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Copied config from 4.14
Add patches for 4.19
Drop patch 103-powerpc-fix-build-cross32ar.patch,
because issue was fixed in upstream.
Compiled: generic p1020
Compiled and tested: (unofficial) P2020, TP-Link TL-WDR4900
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Currently, the image creation process for the TP-Link tl-wdr4900-v1
needs a fixed sized kernel and places the rootfs partition at a
fixed offset. With the upcoming move to 4.19 the kernel will no
longer fit into the existing allocated space for the kernel
partition.
This patch converts the device to utilize the established
tplink,firmware mtdsplitter, which can deal with a dynamic
kernel/rootfs size.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 2T2R
WiFi5: QCA9880 2T2R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED blue
1x LED red
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to reset-button
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
Always enable the pwr led and use the usr led for boot status indication.
Rename nodes in the dts, to match what is recommend in the devicetree
specification.
Increase the maximum spi frequency to 20MHz and drop the m25p,chunked-io
which isn't required on mt7621.
Use the BTN_0 keycode for the mode button. This board doesn't have any
wireless.
Use a more descriptive label for the reset button and the GPIO enabling
the usb vcc supply.
Use the beeper kernel module for the buzzer.
Fix the pinmux to switch only pins used as GPIOs to the GPIO function.
Add support for the PoE enable GPIO to the userspace. The PoE power
status can be read via GPIO7. Since OpenWrt doesn't have support for
reading inputs from userspace, prepare only the pinmux for the GPIO.
Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support of MikroTik RouterBOARD 750Gr3, without the need
to reflashing the bootloader.
Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common
Since the image isn't compatible with RouterBOARD 750Gr3 installations
which have replaced the bootloader, the former used userspace boardname
is not added to the SUPPORTED_DEVICES, to prevent a brick while trying
to upgrade to the image with native support.
Signed-off-by: Anton Arapov <arapov@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Gigabit ethernet adapters using BCM5706/5708/5709/5716 chipset are
common on servers and as easy/cheap to get as Intel based ones.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip. Its 32, 128 and
256 Mbits siblings are supported upstream but this particular size wasn't.
This commit includes patches for kernels 4.14 and 4.19.
Tested on a COMFAST CF-E120A v3 (ath79).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This patch adds the boot-part feature to the apm82181 sata target.
This makes it possible to configure the boot partition size with
the generic CONFIG_TARGET_KERNEL_PARTSIZE symbol.
Please note: For people using custom images: Just like with
CONFIG_TARGET_ROOTFS_PARTSIZE changing the value can cause
sysupgrade to repartition the device!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Use the file extension bin for sysupgrade-tar images with
metadata to unify the file extension across the target/tree.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The exported kernel dtbs can be build as artifacts.
This way, the MyBook Live's DTB is not generated twice.
While at it, give the artifacts their proper name.
For the wndr4700 use the "device-tree" partition name and
for the MyBook Live: "apollo3g.dtb" to match the mbl_boot.scr.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
The U-Boot on WXR-2533DHP employs a complicated dual firmware
protection scheme against corruptions of the kernel and rootfs
images. See the notes in buffalo.sh for details.
specifications:
- Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T)
- 512 MB of RAM (DDR3)
- 256 MB of Flash (NAND)
- 4T4R 2.4/5 GHz Wlan (QCA9980)
- 5x 10/100/1000 Mbps Ethernet
- 10x LEDs, 8x keys (6x buttons, 2x slide-switches)
- 2x USB 3.0 Type-A
- 12VDC/4A AC Adapter
- UART through-hole on PCB
- J3: Vcc, GND, TX, RX from USB port side
- 115200n8
Boot instructions for the initramfs image:
1. Prepare the TFTP server with the initramfs image renamed to
"wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10".
2. Press the "AOSS" button while powering on the WXR-2533DHP.
3. Wait until the "Wireless" LED flashes before releasing the AOSS button.
The WXR-2533DHP will grab the image from TFTP server and will boot it.
Flashing instructions:
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to
let it finish the flashing process.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
This commits adds the "ramdisk" feature to ipq806x target. The
main driving force behind this decision is to facilitate the
installation of OpenWrt on some locked IPQ806x devices.
Examples:
- NEC Aterm WG2600HP
The U-Boot on WG2600HP is protected with a password which prevents
users from gaining access to the u-boot prompt in order to install
the images from there.
Therefore, on this device, installing OpenWrt by the user involves
changing the bootcmd as follows so that WG2600HP downloads and
executes initramfs image from TFTP server.
ex.:
bootcmd="ping ${serverip} && tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq"
- Buffalo WXR-2533DHP
The U-Boot on WXR-2533DHP has built-in firmware recovery mode.
It's activated by holding the "AOSS" button during boot. This
will trigger the device to download the firmware from an TFTP
server and booting from it. By using this, the user can the
install OpenWrt firmware without having access to the UART
console.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
Replace the code with a more readable version. Rename the recipe
to reflect the real usecase.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
The 'factory' partition will move to 0x50000-0x60000 in 2019. As
the webserver in bootloader is compatible with different mtdlayout,
all the users still can upgrade firmware whatever on ath79 or ar71xx.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.
Specifications:
- 650/400/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 26 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new want, so a factory reset will be
needed: once the new firmware is flashed, perform the factory reset by
pushing the reset button several times during the boot process, while the
WAN LED flashes, until it starts flashing quicker.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and keep it
pressed for >10 seconds. The recovery page will be at http://192.168.1.1
Notes:
The device is advertised, sold and labeled as "CF-E110N", but the
bootloader and the stock firmware identify it as "v2".
Acknowledgments:
Petr Štetiar <ynezz@true.cz>
Sebastian Kemper <sebastian_ml@gmx.net>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for TP-Link Archer C6 v2 (EU)
Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board
Flash instructions:
Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
EnGenius EWS511AP is a wireless managed wall AP with PoE support,
based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887.
Short specification:
- 128MB of RAM
- 16 MB of SPI FLASH
- 2T2R 2.4 GHz (QCA9531), 802.11b/g/n
- 1T1R 5 GHz (QCA9887), 802.11ac/n/a
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED
- 1x RESET button
- built-in watchdog chipset
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
Original firmware is based on QSDK.
Use sysupgrade firmware directly in vendor GUI.
Reset to factory default is necessary.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the OpenWrt firmware in the root directory on your computer.
2. Power up EWS511AP. Press 4 and then press any key to enter u-boot.
3. Download OpenWrt firmware
(ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin"
4. Flash the firmware
(ath)> erase 0x9f060000 +f50000
(ath)> cp.b $fileaddr 0x9f060000 $filesize
5. Reboot
(ath)> reset
Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
CPU: Atheros AR9341 535MHz
RAM: 32MB
FLASH: 4MiB
PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan
WiFi: Atheros AR9341 2x2:2 bgn
LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill
BTN: WPS, WiFi, Reset
Installation:
Upload the factory image via the vendor-GUI.
Signed-off-by: Antonio Silverio <menion@gmail.com>
[resolve merge conflicts, squash commits, fix commit title, remove
default default off led properties, mark sysupgrade image compatible
with the ar71xx version of the board, drop blank lines from dts]
Signed-off-by: Mathias Kresin <dev@kresin.me>
With this commit the TP-Link Archer C58 and Archer C59 use caldata
patching in order to set the correct 5GHz MAC-address.
Tested on TP-Link Archer C59 v1.
For more details see commit 330965b.
Signed-off-by: David Bauer <mail@david-bauer.net>
Right now this patch adds nor image generation only. NAND image
generation is not supportet at the moment.
Furtheremore support for the MicroSD port is not implemented as of now.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x switch button, 1x reset button
- LED: 3x LEDS (green)
- Another LED can be accessed on GPIO 7 if soldered
Flash instruction:
- Set static ip to 192.168.1.2
- Unplug the power cord
- Hold reset button
- Plug power back in
- Right led will flash 5 times
- Release reset button
- Browse to 192.168.1.1
- Choose sysupgrade image in NOR-flash section
- Press "update nor firmware"
- After successful transfer unplug network cable before device restarts
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[resolve merge conflicts, rename buttons, use switch input type for mode
switch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The OCEDO Koala has incorrect PLL settings which result in ~3% packet
loss on ethernet connections.
Also omit the gmac-configuration as it's incorrect too.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware spec of DIR-859 A1:
SoC: QCA9563
DRAM: 64MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9880
USB is supported on the PCB but not connected.
Flash instructions:
1. Upgrade the factory.bin through the factory web interface or the u-boot
failsafe interface.
The firmware will boot up correctly for the first time.
Do not power off the device after OpenWrt has booted. Otherwise the u-boot
will enter failsafe mode as the checksum of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
After upgrading completes the u-boot won't complain about the firmware
checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin, just
upgrade the factory.bin through the u-boot failsafe interface and then goto
step 2.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
[squash commits, use common seama recipes, sync factory image recipe
with ramips version]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Create a common template which has the required image build code
defined. Add some new variables to pass individual parts to the seama
recipes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The mask/shift computation used the pin group number instead of the pin
number, resulting in always modifying group 4 when applying muxes, so
fix it to consistently use the pin number.
Fixes: 0755c2d117 ("brcm63xx: add pinctrl support")
Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the switch port order to have the correct order in LuCI.
Fixes: FS#1469
Signed-off-by: Eduardo Barros <geadas@gmail.com>
[trim commit title, add a proper commit message, add fixes tag, keep
alphabetical order of the blocks]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specs
SoC: MT7621AT
RAM: 512MiB
Flash: 32MiB MX25L25635F SPI NOR
2.4G: MT7603EN
5G: MT7612EN
Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs
USB 3.0
LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet.
The last two ones are controlled by GPIO
UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board.
UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip.
The stock u-boot uses UARTLITE1 by default. Baud rate is 57600
Flash instruction
1. telnet 192.168.9.1 2317, username is "root" and password is "admin"
One can alternatively use UART to log in
2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router
One can alternatively download the firmware via wget through Internet
3. mtd write /path/to/openwrt.bin firmware
4. reboot
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui, or via recovery interface:
How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
one manually
3.) Upload original factory image via JBOOT http interface at IP
192.168.123.254
4.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
type "reboot" into the telnet session.
Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The WD MyBook Live SquashFS images didn't work anymore due to
a upstream regression in f2fs commit: 0cfe75c5b01199
("f2fs: enhance sanity_check_raw_super() to avoid potential overflows")
that got backported to 4.14.86 and landed in 4.18.
by Martin Blumenstingl:
|Treat "block_count" from struct f2fs_super_block as 64-bit little endian
|value in sanity_check_raw_super() because struct f2fs_super_block
|declares "block_count" as "__le64".
|
|This fixes a bug where the superblock validation fails on big endian
|devices with the following error:
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock
| F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0)
| F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock
|As result of this the partition cannot be mounted.
|
|With this patch applied the superblock validation works fine and the
|partition can be mounted again:
| F2FS-fs (sda1): Mounted with checkpoint version = 7c84
|
|My little endian x86-64 hardware was able to mount the partition without
|this fix.
|To confirm that mounting f2fs filesystems works on big endian machines
|again I tested this on a 32-bit MIPS big endian (lantiq) device.
Hopefully, this will do until Martin's patch moved through upstream
to -stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MyBook Live DUO used "wd,mybooklive-duo" as the first
compatible string and not "wd_mybooklive-duo".
Fixes: 9b47aa93c7 ("apm821xx: unify My Book Live Single + Duo images")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently all Archer A7 v5 have the same (incorrect) MAC address.
The address is currently derived from eth1 which is not present on the
QCA9563. Use eth0 to get the correct MAC address.
Signed-off-by: David Bauer <mail@david-bauer.net>
