Required for installation of autoconf:
make[5]: Entering directory `/openwrt/build_dir/host/autoconf-2.69'
Making all in bin
make[6]: Entering directory `/openwrt/build_dir/host/autoconf-2.69/bin'
autom4te_perllibdir='..'/lib AUTOM4TE_CFG='../lib/autom4te.cfg'
../bin/autom4te -B '..'/lib -B '..'/lib --language M4sh --cache
'' --melt ./autoconf.as -o autoconf.in
Can't locate Data/Dumper.pm in @INC (@INC contains: ../lib
/usr/local/lib64/perl5 /usr/local/share/perl5 /usr/lib64/perl5/vendor_perl
/usr/share/perl5/vendor_perl /usr/lib64/perl5 /usr/share/perl5 .) at
../lib/Autom4te/C4che.pm line 33.
BEGIN failed--compilation aborted at ../lib/Autom4te/C4che.pm line 33.
Compilation failed in require at ../bin/autom4te line 40.
BEGIN failed--compilation aborted at ../bin/autom4te line 40.
make[6]: *** [autoconf.in] Error 2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
While the effective "default" based on frequent use is "router", the
DEVICE_TYPE variable actually provides a "basic" configuration without
selecting any additional packages.
This is currently set up with the identifier "bootloader", which seems
to be not used at all. However, the only targets not using "router" or
"nas" are actually archs38 and arc770, which use their own value
"developerboard" for DEVICE_TYPE which seems to have been invented when
these targets where added. The latter is not implemented in target.mk,
though, and will fall back to the "basic" set of packages then.
So, to clean this up and make it more readable, let's just define a
DEVICE_TYPE "basic" and use it for the aforementioned cases.
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
zstd with its default settings (compression level -3) compresses better
than bzip2 -9 (which is the default setting), and is an order of magnitude
faster.
I made the following measurements for the most common compression tools
(all standard Debian Buster versions, default flags unless noted
otherwise), using the debug information of a large x86-64 kernel with
ALL_KMODS:
* kernel-debug.tar: 376M
* kernel-debug.tar.gz: 101M, compressed in ~12s
* kernel-debug.tar.bz2: 91M, compressed in ~15s
* kernel-debug.tar.xz: 57M, compressed in ~101s
* kernel-debug.tar.zst: 86M, compressed in ~1s
With zstd, there is still some room for improvement by increasing the
compression, but the slight increase in compression ratio
(22.83% -> 19.46%) does not justify the significant increase in
compression time (about 5 times on my machine) in my opinion.
Note that multithreaded compression (-T argument) does not affect
reproducibility with zstd.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Running make with RECURSIVE_DEP_IS_ERROR=1 will cause a hard failure
when a recursive dependency is detected. This is useful to apply
stricter Ci tests, for example.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
This information already exists in some makefiles. In order for the
information to be processed further, it should also be added to the
manifest file and the control file of ipkg packages.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
undefine was added in make 3.82 which is now some 10 years ago, some
make scripts are beginning to use 'undefine'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ftp can cause problems on some networks switch primary download location
to https and add another mirror
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
xt_MASQUERADE.ko is picked up by both kmod-ipt-nat and kmod-ipt-nat6, causing
conflict
As kmod-ipt-nat6 already depends on kmod-ipt-nat, remove xt_MASQUERADE from it
Fixes: FS#2924
Fixes: 0fad8af851 ("kernel: Include xt_MASQUERADE for kernel 5.2 and later")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This reverts commit 3204430e38.
Reverting this commit in preparation for reverting
dcf3e63a35 ("build: scripts/config - update to kconfig-v5.6") which
introduces various unaddressed build breakages.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This addes the option to treat recursive dependencies as warnings
instead of errors, by running make with WARN_RECURSIVE_DEP=1.
Note that the script/config targets will not get rebuilt when you add or
remove WARN_RECURSIVE_DEP while running make. One must run
'make config-clean' before building config with a different setting.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Instead of passing pkg-config location through a variable when building
qconf (make xconfig), prepend its parent directory to the PATH, as it is
being done for other conf targets.
Use a Makefile pattern rule to group all 'scripts/config/%onf'
(currently conf, mconf, qconf) targets in a single rule. Add -O2 to
CFLAGS when building them as well.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The symvers files of older kernel versions are incompatible with the ones
from 5.4, so changing the kernel version without running make clean was
causing build failures in kernel module packages.
Fix this by moving the directory, ensuring that symvers files get thrown
away with a kernel version change
Signed-off-by: Felix Fietkau <nbd@nbd.name>
JSON info files contain machine readable information of built profiles
and resulting images. These files were added in commit 881ed09ee6
("build: create JSON files containing image info").
They are useful for firmware wizards and script checking for
reproducibility.
Currently all JSON files are stored next to the built images, resulting
in up to 168 individual files for the ath79/generic target.
This patch refactors the JSON creation to store individual per image
(not per profile) files in $(BUILD_DIR)/json_info_files and create an
single overview file called `profiles.json` in the target directory.
Storing per image files and not per profile solves the problem of
parallel file writes. If a profiles sysupgrade and factory image are
finished at the same time both processes would write to the same JSON
file, resulting in randomly broken outputs.
Some target like x86/64 do not use the image code yet, resulting in
missing JSON files. If no JSON info files were created, no
`profiles.json` files is created as it would be empty anyway.
As before, this creation is enabled by default only if `BUILDBOT` is set.
Tested via buildroot & ImageBuilder on ath79/generic, imx6 and x86/64.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[json_info_files dir handling in Make, if case refactoring]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.
EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.
GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
There is a restriction in the number of parameters(10) that may be passed to
the SetupHostCommand macro so continually adding explicit gcc'n' version
checks ends up breaking the compiler check for the later versions and
oddballs like Darwin as was done in 835d1c68a0 which added gcc10.
Drop all the explicitly specified gcc version checks. If a suitable gcc
compiler is not found, it may be specified at the dependency checking
stage after which that version will be symlinked into the build staging
host directory.
eg. 'CC=gccfoo CXX=g++foo make prereq'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Lets add GCC 10 detection to the build system as distributions like Fedora 32 have started shipping with it.
Some tools like mtd-utils need work to compile under GCC10, but that will be next step.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In most cases check-size is used with IMAGE_SIZE and vice versa. Let check-size
use IMAGE_SIZE by default.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This commit introduces few related changes which need to be done in
single commit to keep images buildable between git revisions. In result
it retains all previous image creation possibilities with slight name
change of generated images. Brief summary of the commit:
* Split up image generation recipe to smaller chunks to make it more
generic and reusable.
* Make iso images x86 specific and drop their definition as root
filesystem.
* Convert image creation process to generic code specified in image.mk.
* Make geode subtarget inherit features from the main target instead of
redefining them.
* For subtargets create device definitions with basic packages set.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebased]
Signed-off-by: Paul Spooren <mail@aparcar.org>
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
getopt is the only command where /usr/local/bin is specified explicitly.
All other commands are assumed to exist in the PATH in one form or
another. Remove this exception and require gnugetopt/getopt to be in
the user's PATH.
In the case of macos Homebrew, getopt is 'keg only' hence not linked
into /usr/local/bin whilst other commands are linked and likely found by
virtue of /usr/local/bin being in PATH.
Since 2019 Homebrew is very reluctant to install links that have
potential to override default OS behaviour, eg: following instructions
on our current 'how to build on macos' wiki page:
$ brew ln gnu-getopt --force
Warning: Refusing to link macOS-provided software: gnu-getopt
If you need to have gnu-getopt first in your PATH run:
echo 'export PATH="/usr/local/opt/gnu-getopt/bin:$PATH"' >> ~/.zshrc
A better option for macos is to link getopt as 'gnugetopt' in
/usr/local/bin, thus the build system will find 'gnugetopt' but other
applications looking for just 'getopt' will find the original macos
binary.
Ultimately it makes sense that 'GNU' dependencies are placed in
/usr/local/bin and /usr/local/bin is included in the user's PATH.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Build/InstallDev no longer places a file list in
$(STAGING_DIR_HOST)/packages; this change removes the creation of
$(STAGING_DIR_HOST)/packages and the attempted removal of a
STAGING_DIR_HOST file list during package clean.
This also changes the host directory passed to Build/UninstallDev from
$(STAGING_DIR_HOST) to $(STAGING_DIR)/host, to match the directory
passed to Build/InstallDev.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
Build system needs an 'xargs' that supports '-r' which darwin doesn't.
Homebrew installs a 'gxargs' with the findutils package so look for
'gxargs' as well as 'xargs'
This is a bit of a 'fun' corner case anyway. xargs is only required by
the build if 'CONFIG_AUTOREMOVE' is set and after the build system has
built 'tools/findutils' we have a fully working xargs for host anyway.
Until that time we have to rely on the host's xargs implementation.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The following patches were removed because they are integrated in the upstream kernel 5.4:
* backport-5.4/047-v4.21-mtd-keep-original-flags-for-every-struct-mtd_info.patch
* backport-5.4/048-v4.21-mtd-improve-calculating-partition-boundaries-when-ch.patch
* backport-5.4/080-v5.1-0001-bcma-keep-a-direct-pointer-to-the-struct-device.patch
* backport-5.4/080-v5.1-0002-bcma-use-dev_-printing-functions.patch
* backport-5.4/095-Allow-class-e-address-assignment-via-ifconfig-ioctl.patch
* backport-5.4/101-arm-cns3xxx-use-actual-size-reads-for-PCIe.patch
* backport-5.4/200-v5.2-usb-dwc2-Set-lpm-mode-parameters-depend-on-HW-configuration.patch
* backport-5.4/210-arm64-sve-Disentangle-uapi-asm-ptrace.h-from-uapi-as.patch
* backport-5.4/380-v5.3-net-sched-Introduce-act_ctinfo-action.patch
* backport-5.4/450-v5.0-mtd-spinand-winbond-Add-support-for-W25N01GV.patch
* backport-5.4/451-v5.0-mtd-spinand-Add-initial-support-for-Toshiba-TC58CVG2.patch
* backport-5.4/452-v5.0-mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
* backport-5.4/455-v5.1-mtd-spinand-Add-support-for-all-Toshiba-Memory-produ.patch
* backport-5.4/456-v5.1-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
* backport-5.4/460-v5.0-mtd-spi-nor-Add-support-for-mx25u12835f.patch
* backport-5.4/460-v5.3-mtd-spinand-Define-macros-for-page-read-ops-with-thr.patch
* backport-5.4/461-v5.3-mtd-spinand-Add-support-for-two-byte-device-IDs.patch
* backport-5.4/462-v5.3-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UFxxG.patch
* backport-5.4/463-v5.3-mtd-spinand-Add-initial-support-for-Paragon-PN26G0xA.patch
* backport-5.4/700-v5.1-net-phylink-only-call-mac_config-during-resolve-when.patch
* backport-5.4/701-v5.2-net-phylink-ensure-inband-AN-works-correctly.patch
* backport-5.4/702-v4.20-net-ethernet-Add-helper-for-MACs-which-support-asym-.patch
* backport-5.4/703-v4.20-net-ethernet-Add-helper-for-set_pauseparam-for-Asym-.patch
* backport-5.4/704-v4.20-net-phy-Stop-with-excessive-soft-reset.patch
* backport-5.4/705-v5.1-net-phy-provide-full-set-of-accessor-functions-to-MM.patch
* backport-5.4/706-v5.1-net-phy-add-register-modifying-helpers-returning-1-o.patch
* backport-5.4/707-v5.1-net-phy-add-genphy_c45_check_and_restart_aneg.patch
* backport-5.4/708-v5.3-net-phylink-remove-netdev-from-phylink-mii-ioctl-emu.patch
* backport-5.4/709-v5.3-net-phylink-support-for-link-gpio-interrupt.patch
* backport-5.4/710-v5.3-net-phy-allow-Clause-45-access-via-mii-ioctl.patch
* backport-5.4/711-v5.3-net-sfp-add-mandatory-attach-detach-methods-for-sfp-.patch
* backport-5.4/712-v5.3-net-sfp-remove-sfp-bus-use-of-netdevs.patch
* backport-5.4/713-v5.2-net-phylink-avoid-reducing-support-mask.patch
* backport-5.4/714-v5.3-net-sfp-Stop-SFP-polling-and-interrupt-handling-duri.patch
* backport-5.4/715-v5.3-net-phylink-don-t-start-and-stop-SGMII-PHYs-in-SFP-m.patch
* backport-5.4/740-v5.5-net-phy-avoid-matching-all-ones-clause-45-PHY-IDs.patch
* backport-5.4/741-v5.5-net-phylink-fix-link-mode-modification-in-PHY-mode.patch
* pending-5.4/103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch
* pending-5.4/131-spi-use-gpio_set_value_cansleep-for-setting-chipsele.patch
* pending-5.4/132-spi-spi-gpio-fix-crash-when-num-chipselects-is-0.patch
* pending-5.4/220-optimize_inlining.patch
* pending-5.4/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
* pending-5.4/475-mtd-spi-nor-Add-Winbond-w25q128jv-support.patch
* pending-5.4/477-mtd-add-spi-nor-add-mx25u3235f.patch
* pending-5.4/479-mtd-spi-nor-add-eon-en25qh64.patch
Some bigger changes were done to this feature and we did not port this patch yet:
* hack-5.4/207-disable-modorder.patch
This depends on BOOTMEM which was removed from the kernel, this needs some bigger changes:
* hack-5.4/930-crashlog.patch
A different version of the FPU disable patch was merged upstream, OpenWrt needs some adaptations.
* pending-5.4/304-mips_disable_fpu.patch
- no crashlog support yet as a required file got deleted upstream
- Removed patch below, which is now seen as a recursive dependency [1]
- Removed patch below due to build error [2]
- fix still required to avoid identical function def [3]
- Fixes included from Blocktrron
- Fixes included from Chunkeey
- Fix included from nbd regarding "dst leak in Flow Offload"
[1] target/linux/generic/hack-5.4/260-crypto_test_dependencies.patch
[2] target/linux/generic/hack-5.4/207-disable-modorder.patch
[3] target/linux/generic/pending-5.4/613-netfilter_optional_tcp_window_check.patch
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some targets like kirkwood or omap don't use a subtarget which results
in a malformed JSON info file.
Instead of having a valid value like `"target": "ath79/tiny"` for these
targets the value is `"target": "kirkwood/"`.
This patch uses the same if condition to use `generic` if the subtarget
is empty.
Tested for the kirkwood target.
Signed-off-by: Paul Spooren <mail@aparcar.org>
In Linux kernel commit 8377bd2b9ee1 ("kbuild: Rename HOST_LOADLIBES to
KBUILD_HOSTLDLIBS") HOST_LOADLIBES was renamed to KBUILD_HOSTLDLIBS.
This patch adapts the OpenWrt kernel build to this new variable. Without
this change the kernel host tools would not link against the libraries
found in the staging directory.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Most of the kernel version switches below 4.14 were removed in commit
97940f8766 ("kernel: remove obsolete kernel version switches"),
but some of them still remained. Remove them now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Certain boards have limitations on U-Boot that prevent flashing
of images where the kernel size exceeds a threshold, yet
sysupgrade can sucessfully manage larger kernels. The current
check-size will remove the target artifact if its total size
exceeds the threshold. If applied after append-kernel,
it will remove the kernel, but the remaining image-assembly
steps will continue, resulting in an image without a kernel
that is likely unbootable.
By defining check-kernel-size, it is now possible to prevent release
of such unbootable images through a construct similar to:
IMAGE/factory.img := append-kernel | pad-to $$$$(GL_UBOOT_UBI_OFFSET) | \
append-ubi | check-kernel-size $$$$(GL_UBOOT_UBI_OFFSET)
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Setting CONFIG_IPK_FILES_CHECKSUMS=y causes sha256 checksum files to be
included with the packages to check for corruption. This commit fixes two
issues:
- /sbin/pkg_check was being removed incorrectly if IPK_FILES_CHECKSUMS=y
- checksums were being saved in the wrong file
Signed-off-by: Xu Wang <xwang1498@gmx.com>
Package new kmods "nf_tables_set" and "nft_objref" which got introduced
with kernel 4.18 and restrict the old "nft_set_rbtree" and "nft_set_hash"
modules to sub-4.18 versions.
Also reorder the nftables related netfilter.mk entries alphabetically
while touching this code section.
Fixes: FS#2699
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2699#comment7450
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This tristate choose allows to select to build only some applications
with PIE enabled. On MIPS binaries are getting about 30% bigger when PIE
is activated for the, which is a huge increase.
Network exposed applications like dnsmasq should then be build with PIE
enabled, but some applications which are normally not parsing data from
the network do not have it activated. The regular option should give a
good trade off between extra flash and RAM memory usage and security.
This changes the default from building no applications with PIE to build
some specifically marked applications with PIE enabled. This option is
only activated for targets with bigger flash and RAM to not consume
extra memory on the very small targets. On SDK builds the Regular option
should always be selected, because some tiny targets share the
applications with big targets and only the images for the tiny targets
should contain the none PIE applications, but the images for the normal
targets should use PIE. The shared packages should always use PIE when
it should be normally activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
nft_hash hash falsely removed in commit 97940f8766
("kernel: remove obsolete kernel version switches").
Add the module back, as otherwise the build fails.
Fixes: 97940f8766 ("kernel: remove obsolete kernel version switches")
Signed-off-by: David Bauer <mail@david-bauer.net>
After kernel 4.9 has been removed, this removes all (now obsolete)
kernel version switches that deal with versions before 4.14.
Package kmod-crypto-iv is empty now and thus removed entirely.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This move the slightly different target-specific implementations of
mktplinkfw from the targets to include/image-commands.mk and renames
it to tplink-v1-image. Having a common version will increase
consistency between implementation and will complete the
tplink build command already present in the new location.
Due to the slight differences of the original implementations, this
also does some adjustments to the device build commands/variables.
This also moves rootfs_align as this is required as dependency.
Tested on:
- TL-WDR4300 v1 (ath79, factory)
- TL-WDR4900 v1 (mpc85xx, sysupgrade)
- RE210 v1 (ramips, see Tested-by)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Christoph Krapp <achterin@googlemail.com>
Several CMake packages such as log4cplus and protobuf(-c) install to
lib64 instead of lib on some hosts. This completely breaks rpath linking.
Override it globally to avoid fixing each package individually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Sebastian Kemper <sebastian_ml@gmx.net>
Currently in OpenWrt, there are two libc++: libstdcpp and uClibc++. The
former is huge and the latter supports only C++98 with some basic support
for C++11. Those C++ versions seem to be specific to the compiler version
libcxx supports C++11 and above while being much smaller than libstdcpp.
On mt7621, these are the sizes of the ipks that I get:
libstdcpp: 460786
libcxx: 182881
uClibc++:67720
libcxx is faster than uClibc++ and is under active development as part of
the LLVM project while uClibc++ is effectively dead.
This PR modifies uclibc++.mk to expose the make menuconfig option. Further
cleanup is beyond the scope of this PR. What that means is, this is not
used by default.
A g++-libcxx wrapper based on the uClibc++ one was added. Works the same
way.
Compile tested with all packages that use uclibc++.mk in their Makefiles
under mipsel_24kc. kismet fails compilation but that package needs to be
cleaned up and updated.
Runtime tested with gddrescue, gdisk, dcwapd, bonnie++, and aircrack-ng
on a TP-Link Archer C7v2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This creates the device variable SOC and adds it to DEFAULT_DEVICE_VARS.
It is supposed to replace target-specific SOC variables like ATH_SOC or
MTK_SOC and thus unify variable names across targets.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Don't put CC_HAS_ASM_GOTO, IS_GCC, IS_CLANG and GCC_VERSION runtime
config options into the kernel configs during reconfiguration as it
makes no sense, since these options should be set at runtime.
Fixes: FS#2588
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It seems that there is a missing PKG_SOURCE_URL_FILE support.
This little fix adds the support for packages to change the name of the
downloaded file.
Sometimes it is desirable to change the downloaded archive file name, like
for mitigating name conflicts for different packages (some files on the server
could be named like, e.g. 2018-01-01.tar.gz) or for the cases that there is
no name for the file in the URL (e.g. http://someserver.com/download).
Signed-off-by: Kamil Wcislo <kamil.wcislo@lpnplant.io>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add support for Python 3.8 which was released Oct. 14, 2019.
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
[added missing commit description, simplified version check]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit 965f341aa9 ("build: fix host menu config targets using
ncurses") has moved host's path with pkg-config (usually /usr/bin) at
the first place in PATH variable, which is now causing issues with bison
as BISON_PKGDATADIR points into STAGING_DIR_HOST, but the actual bison
used is the one under host PATH (usually /usr/bin/bison), leading to the
following strange failures:
$ make target/linux/clean kernel_menuconfig V=sc
export MAKEFLAGS= ;make -C /somewhere/linux-4.19.81 menuconfig
make -f ./scripts/Makefile.build obj=scripts/kconfig menuconfig
...
bison -oscripts/kconfig/zconf.tab.c -t -l scripts/kconfig/zconf.y
staging_dir/host/bin/m4: cannot open `staging_dir/host/share/bison/bison.m4': No such file or directory
staging_dir/host/bin/m4: cannot open `staging_dir/host/share/bison/c-skel.m4': No such file or directory
...
gcc -Wp,-MD,scripts/kconfig/.zconf.tab.o.d <...snip...> -o scripts/kconfig/zconf.tab.o scripts/kconfig/zconf.tab.c
gcc: error: scripts/kconfig/zconf.tab.c: No such file or directory
gcc: fatal error: no input files
Fix this by forcing usage of bison under STAGING_DIR_HOST/bin via YACC
make variable.
Cc: Thomas Albers <thomas.gameiro@gmail.com>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Cc: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Ivan Revyakin <LovingFox@GMail.com>
Tested-by: Thomas Albers <thomas.gameiro@googlemail.com>
Ref: https://forum.openwrt.org/t/bpi-r64-kernel-4-19-kernel-menuconfig-error
Fixes: 965f341aa9 ("build: fix host menu config targets using ncurses")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Replace 2 instances of non posix use of 'head' with posix compliant
'cut'.
'head -c n' cuts 'n' bytes from the passed string and happens to work on
Linux & Mac OS X even though '-c' is not posix.
'head --bytes n' does the same thing and happens to work on linux but
not on Mac OS X and is also not posix.
'cut -b1-8' cuts the first 8 bytes from the passed string and is posix
compliant, hence works on Linux & Mac OS X.
Our usage of 'head --bytes' was particularly unfortunate since it was
used to calculated the RootFS UUID passed to grub - the net result being
a non-functioning system waiting for the root file system to appear.
Thanks to karlp, ynezz & others for pointers on solving this.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
x86, mvebu and tegra targets are currently using more or less same
SIGNATURE variable which provides unique partition ID/signature, so it
makes sense to refactor it out into common variable which could be
reused by all targets. While at it, make the content of the variable
reproducible.
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2019-March/016148.html
Signed-off-by: Paul Spooren <mail@aparcar.org>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
[renamed to IMG_PARTSIGNATURE, reworked with epoch+vermagic hash]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit 881ed09ee6 ("build: create JSON files containing image info")
has removed the crucial empty new line from the image copy step
resulting in the following errors during make function expansion:
GZ_SUFFIX :=
bash: GZ_SUFFIX: command not found
Makefile:86: recipe for target 'openwrt-ath79-generic-tplink_archer-c7-v5-squashfs-sysupgrade.bin' failed
Fixes: 881ed09ee6 ("build: create JSON files containing image info")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
UUID of ext4 volumes generated by make_ext4fs are determined by volume
label and it will all be 57f8f4bc-abf4-655f-bf67-946fc0f9f25b when label
is empty
Labeling them does not make them unique but tools like block command
from fstools have a better chance differentiating them
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
It's related to the upstream kernel commit adf82accc5f5 ("netfilter:
x_tables: merge ip and ipv6 masquerade modules").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The luci and freifunk feed having a common Makefile included by the
individual packages. Currently a change to this file will be ignored
when running "scripts/feeds update".
When we are updating for a feed, add a dependency for all .mk files
in the root of it.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
This separates the options for signature creation and verification
* SIGNED_PACKAGES create Packages.sig
* SIGNED_IMAGES add ucert signature to created images
* CHECK_SIGNATURE add verification capabilities to images
* INSTALL_LOCAL_KEY add local key-build to /etc/opkg/keys
Right now the buildbot.git contains some hacks to create images that
have signature verification capabilities while not storing private keys
on buildbot slaves. This commit allows to disable these steps for the
buildbots and only perform signing on the master.
Signed-off-by: Paul Spooren <mail@aparcar.org>
'append-uImage-fakehdr' can now accept magic number as a second, optional
parameter (passed directly to 'mkimage' command with '-M' option). This
enables construction of proper Netgear-specific fake rootfs images
(required for flashing WNDR4300 for example).
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Problem found on alpine linux when trying to `./scripts/feeds update -a`,
which results in `Build dependency: Missing seq command`.
Ref: https://github.com/openwrt/openwrt/pull/1926
Suggested-by: imShara <shara@protonmail.com>
[reworded commit and turned faulty Sob into Suggested-by]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some kmods (gpio-hotplug, wireguard) store the build path in the
compiled files and therefore make it harder to rebuild the official
binaries. As the same "iremap" function is used as for other binaries,
the change is compatible with gcc7 and 8.
Tested with both gcc7 and gcc8 resulting in build path independent
reproducible builds.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This is a follow up of 8cb13f4e6d which sets the right timestamp for the
/init file in initramfs. The previous patch doesn't cover it as the
files appear to come from a later step during compilation.
CC: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Paul Spooren <mail@aparcar.org>
The check for libelf in the kernel build is not enough, because the code that
uses libelf for stack validation is completely non-portable, as it tries to
include asm/types.h and relies on kernel types in user space.
Until this is fixed properly, the only solution is to disable this on any non
Linux build host
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The JSON info files contain details about the created firmware images
per device and are stored next to the created images.
The JSON files are stored as "$(IMAGE_PREFIX).json" and contain some
device/image meta data as well as a list of created firmware images.
An example of openwrt-ramips-rt305x-aztech_hw550-3g.json
{
"id": "aztech_hw550-3g",
"image_prefix": "openwrt-ramips-rt305x-aztech_hw550-3g",
"images": [
{
"name": "openwrt-ramips-rt305x-aztech_hw550-3g-squashfs-sysupgrade.bin",
"sha256": "db2b34b0ec4a83d9bf612cf66fab0dc3722b191cb9bedf111e5627a4298baf20",
"type": "sysupgrade"
}
],
"metadata_version": 1,
"supported_devices": [
"aztech,hw550-3g",
"hw550-3g"
],
"target": "ramips/rt305x",
"titles": [
{
"model": "HW550-3G",
"vendor": "Aztech"
},
{
"model": "ALL0239-3G",
"vendor": "Allnet"
}
],
"version_commit": "r10920+123-0cc87b3bac",
"version_number": "SNAPSHOT"
}
Signed-off-by: Paul Spooren <mail@aparcar.org>
On a recent Gentoo Linux installation, invoking `make menuconfig`, `make
kernel_menuconfig` or `make kernel_nconfig` in the build system fails,
whereas for example `make menuconfig` in the kernel tree alone works as
expected.
This is happening because STAGING_PREFIX is not defined when kernel's
{menu,n}config target calls pkg-config from the toolchain/host and thus
pkg-config returns an empty value, and the fallback values in the kernel
config script are applied but those are off and the linking fails.
Solution is to use system's pkg-config for all ncurses based menu config
targets in order to provide proper compiler/linker flags.
Ref: FS#2423
Cc: Thomas Albers <thomas.gameiro@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Some tools doesn't support SOURCE_DATE_EPOCH (e.g. initramfs images).
Ensure all files of a root filesystem are set to SOURCE_DATE_EPOCH.
Make initramfs builds reproducible (for ramips).
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This patch removes scons host build tool, as commit 7087efd72a8d
("scons: move host build tool to a proper place") in the packages feed
has moved scons into the new home.
There are currently no packages in the master tree which would need
scons, yet scons is build always as part of host tools, just in order to
satisfy host build dependency of few packages in the packages feeds.
Ref: https://github.com/openwrt/packages/pull/9584
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently for at91 target, Build/install-dtb can be triggered concurrently for
multiple different TARGET_FILESYSTEMS, cp command can fail when the
target file is already open exclusively by other cp process
[ -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/at91sam9263ek-uImage -a -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/root.ubifs+fs=-m_2048_-e_126KiB_-c_2048+pkg=68b329da ]
[ -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/at91sam9263ek-uImage -a -f /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/root.ext4+pkg=68b329da ]
cp -fpR /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/linux-4.14.141/arch/arm/boot/dts/at91sam9263ek.dtb /builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb;
cp -fpR /builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/linux-4.14.141/arch/arm/boot/dts/at91sam9263ek.dtb /builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb;
cp: cannot create regular file '/builder/shared-workdir/build/bin/targets/at91/sam9x/openwrt-at91-sam9x-at91sam9263ek.dtb': File exists
Makefile:87: recipe for target '/builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/tmp/openwrt-at91-sam9x-at91sam9263ek-ubifs-dtb' failed
make[4]: *** [/builder/shared-workdir/build/build_dir/target-arm_arm926ej-s_musl_eabi/linux-at91_sam9x/tmp/openwrt-at91-sam9x-at91sam9263ek-ubifs-dtb] Error 1
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This reverts commit 1c0290c5cc.
Dropping the nopad can make the padding overflow into the next erase
block on devices using a non-aligned rootfs start. This breaks the jffs2
overlay partition with the following messages:
[ 30.343877] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
[ 30.376512] jffs2: Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
[ 30.385253] jffs2: empty_blocks 196, bad_blocks 0, c->nr_blocks 197
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Pass suitable pkg-config overrides to the kernel build process in
order to let our pkg-config wrapper discover libraries provided
by tools/.
This mainly affects the use of libelf which is required for the
CONFIG_STACK_VALIDATION features. So far, the build system either
silently used host system libraries or kbuild simply disabled the
feature due to the lack of a suitable libelf.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While the -nopad option prevents mksquashfs from padding the
image to an arbitrary 4k. It does not take into consideration
that squashfs is programmed to have this 4k padding when it's
being used on on a block device... which is its main "use-case".
Now, after a week long discussion on the ML that included a
back-and-forth between some of the possible options.
But this is likely the best KISS patch to deal with the issue
right away given the limited resources.
From squashfs code point of view, be warned. The 4k padding is
not enough when dealing with devices that have a PAGE_SIZE
bigger than 4k.
if it turns out to be affecting you, then please look-up either:
"FS#2460 - kernel panic reading squashfs from ubi volume" bug
Or the discussion on the OpenWrt-Devel ML in
"amp821xx: use newly added pad-squashfs for Meraki MR24" and
"Squashfs breakage lottery with UBI..."
before making an educated guess.
Note: This will not affect the "tiny"/small flash devices as
much as it seems at first. This is because the the rootfs_data
partition that follows uses jffs2. And it requires to be aligned
to the flash block-size in order to work at all.
So either the involved FSes will meet in the middle as before,
or not at all. But in that latter case the image was already
hoping for the "undefined behaviour" gamble to turn out in its
favour and this is probably why this was unnoticed for so long.
Fixes: FS#2460
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Refreshed all patches.
Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Also add a missing symbol for x86 which got used now in this bump.
- ISCSI_IBFT
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Underscores don't harm in filenames, however the sanitize function from
version.mk replaces them, causing inconsistent filenames.
A fix tried to solve this previously via
dfe99645db however I did not look close
enough:
openwrt-ath79-generic-8dev-carambola2.manifest # current
openwrt-ath79-generic_8dev-carambola2.manifest # patched
---------------------^
Eventually the sanitization of PROFILES *could* be removed as more and
more profiles follow the device tree approach of vendor_model, neither
containing upper case letters nor spaces.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Some devices are produced and sold under different names. To debloat
the buildroot but keeping it complete, new variables are introduced to
handle different namings. Below an example taken from a recent PR[0]
DEVICE_VENDOR := Arcadyan
DEVICE_MODEL := ARV4520PW
DEVICE_ALT0_VENDOR := Vodafone
DEVICE_ALT0_MODEL := Easybox 800
DEVICE_ALT1_VENDOR := Airties
DEVICE_ALT1_MODEL := WAV-281
With this commit the buildroot is extended to take care of up to three
alternative namings. The primary title plus alternatives names (if
defined) are shown in the `make menuconfig` dialog. Selecting on of
devices automatically selects all alternative names as they share the
same profile.
A list of the newly introduced variables:
DEVICE_ALT0_VENDOR :=
DEVICE_ALT0_MODEL :=
DEVICE_ALT0_VARIANT :=
DEVICE_ALT1_VENDOR :=
DEVICE_ALT1_MODEL :=
DEVICE_ALT1_VARIANT :=
DEVICE_ALT2_VENDOR :=
DEVICE_ALT2_MODEL :=
DEVICE_ALT2_VARIANT :=
[0]: https://github.com/openwrt/openwrt/pull/2229/files#diff-b436f01932a18876c27800ba183d95f6R140
Signed-off-by: Paul Spooren <mail@aparcar.org>
The LEDE URL is automatically redirected to the OpenWRT one,
returning an HTTP 301 code (Moved Permanently).
Also, use https, as indicated by the redirect.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Allow overriding the default selection state for Devices, similar to
setting a default for packages.
E.g. by setting DEFAULT to n, they won't be selected by default anymore
when enabling all device in the multi device profile.
This allows preventing images being built by the default config for
known broken devices, devices without enough RAM/flash, or devices not
working with a certain kernel versions.
This does not prevent the devices from being manually selected or images
being built by the ImageBuilder. These devices often still have worth
with a reduced package-set, or as a device for regression testing, when
no better device is available.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
The manifest file is based on IMG_PREFIX and PROFILE_SANITIZED, whereas
the latter takes a string like DEVICE_8dev_carambola2 and sanitizes it.
This behaviour results in a useless "device_" profile-prefix in the
device manifest filename. Now uses *subst* to remove that.
Therefore this patch results more consistent device file names:
openwrt-ath79-generic-8dev_carambola2-initramfs-kernel.bin
openwrt-ath79-generic-8dev-carambola2.manifest
openwrt-ath79-generic-8dev_carambola2-squashfs-sysupgrade.bin
instead of a single file being called
openwrt-ath79-generic-device_8dev-carambola2.manifest
Signed-off-by: Paul Spooren <mail@aparcar.org>
Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85)
Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e)
Revert "ramips: add preliminary support for WIO ONE" (085141dc5b)
Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539)
Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d)
Revert "toolchain: add autoconf-lean" (fdb30eed03)
Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Github releases usually don't contain the project name in the release
filename, which makes them very inconvenient to use from the build
system. Add support for naming the local file differently.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into
account (if set), so that packages do not need to manually override
PKG_BUILD_DIR just to handle variants.
This also updates most base packages with variants to use the updated
default PKG_BUILD_DIR.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
I'm trying to create a package for libgpiod, which uses
AC_CONFIG_AUX_DIR macro, which is probably leading to the following
configure error:
autoreconf: running: /openwrt.git/staging_dir/host/bin/libtoolize --force
OpenWrt-libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR, `autostuff'.
OpenWrt-libtoolize: linking file `autostuff/ltmain.sh'
OpenWrt-libtoolize: putting macros in `m4'.
...
configure: error: cannot find install-sh, install.sh, or shtool in autostuff "."/autostuff
>From the build output it's clear, that libtoolize isn't installing
install-sh symlink, because libtoolize would install install-sh only if
it's being run with --install parameter. Corresponding part in
libtoolize:
if $opt_install; then
func_config_update config.guess \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
func_config_update config.sub \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
func_install_update install-sh \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
fi
func_ltmain_update ltmain.sh \
"$pkgdatadir/config" "$auxdir" pkgconfig_header
Adding --install parameter to libtoolize fixes this build issue:
autoreconf: running: /openwrt.git/staging_dir/host/bin/libtoolize --install --force
OpenWrt-libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR, `autostuff'.
OpenWrt-libtoolize: linking file `autostuff/config.guess'
OpenWrt-libtoolize: linking file `autostuff/config.sub'
OpenWrt-libtoolize: linking file `autostuff/install-sh'
OpenWrt-libtoolize: linking file `autostuff/ltmain.sh'
OpenWrt-libtoolize: putting macros in `m4'.
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When bumping buildroot to Python 3, we need to assure, that Python
symlink in staging bin directory points to Python >= 3.5 as well.
We can't rely completly just on SetupHostCommand as its executed only in
cases when the $(STAGING_DIR_HOST)/bin/python doesn't already exist, so
we need to remove it before running SetupHostCommand.
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch switches Python used in buildroot to Python 3 as Python 2.x
series is going to be EOL relatively soon[1].
"Being the last of the Python 2.x series, 2.7 will have an extended
period of maintenance. Specifically, 2.7 will receive bugfix support
until January 1, 2020. After the last release, 2.7 will receive no
support."
It seems like Python 3 is going to be needed in order to support Meson
build system which has gained some traction recently.
Build tested on following targets:
ath79/generic
imx6/generic
ipq40xx/generic
lantiq/xway
layerscape/armv7 (broken)
layerscape/armv8_32b (broken)
layerscape/armv8_64b (broken)
mvebu/cortexa72
ramips/mt7621
ramips/mt7620
sunxi/cortexa7
x86/64
Layerscape targets are unfortunately left broken as their ls-rcw
firmware package uses Python 2 and converting it to Python 3 would take
more then reasoanble amount of time (I've tried to fix it already) and
would be better fixed by someone who can even run test it.
Run tested on ath79 (Archer C7 v5), ipq40xx (nbg6617) and x86_64 (QEMU
and apu2).
1. https://www.python.org/dev/peps/pep-0373/
Ref: PR#1937
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Mathew McBride <matt@traverse.com.au>
Acked-by: Yousong Zhou <yszhou4tech@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This feature is similar to the SRC_TREE_OVERRIDE. However instead of having
to manually create a symlink inside the package folder, the buildsystem
will check if $(TOP_DIR)/src-checkout/$(PKG_NAME)/.git is present and use
this instead.
Signed-off-by: John Crispin <john@phrozen.org>
This allows the definition of DEVICE_VENDOR, DEVICE_MODEL and
DEVICE_VARIANT. All three are merged together to look the same as the
current DEVICE_TITLE. Also, if DEVICE_TITLE is set it's directly used as
a *fallback* for devices which weren't upgraded yet.
This is based on the work of @sudhanshu16.
The motivation is to create JSON files based on provided metadata,
needing clear differentiation between vendor, model and revision.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since we switched to 4.19, the kernel build checks for libelf to decide if
it should build tools for stack validation.
On macOS, this check fails during target/compile, but succeeds during package
build (because of the pkg-config path picking up target libraries).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Image padding with dd needs to be done in an OS independent way as not
all dd understand capital letter unit specifiers, and not all understand
lowercase either.
Fixes: 97833a57ef ("build: image: add pad-to and pad-rootfs-squashfs helpers")
Reported-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This common code could be shared by at least 3 targets (malta, armvirt
and x86) so let's factor it out to separate variable.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Declaring a package without the appropriate install section is an easy
mistake to make, especially when renaming packages. Since this is also
easy to detect, warn about it when it happens.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
No-objections-at-all-by: Jo-Philipp Wich <jo@mein.io>
Recent kernel versions need toolchain in order to properly configure
kernel, for example to set CC_HAS_ASM_GOTO config symbol, so missing
toolchain leads to the following error while running `make
kernel_oldconfig` on ath79 target with 4.19 kernel in the clean tree:
init/Kconfig:17: syntax error
init/Kconfig:16: invalid option
./scripts/clang-version.sh: line 15: mips-openwrt-linux-musl-gcc: command not found
./scripts/gcc-plugin.sh: line 11: mips-openwrt-linux-musl-gcc: command not found
net/sched/Kconfig:44: warning: menuconfig statement without prompt
make[4]: *** [scripts/kconfig/Makefile:69: oldconfig] Error 1
So in order to support this new kernel versions, this patch adds
toolchain as a hard dependency to the kernel_*config targets.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Extend the packageauxvars database to keep a list of possible package
dependencies for each provider, then utilize this information in buildroot
to resolve the ABI version dependencies of dependent packages up to five
levels deep.
This should properly trigger rebuilds for packages indirectly depending
on other packages whose ABI_VERSION changed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Also fix a malformed patch issue caught during refresh.
It was caused by removing a whitespace without altering
the index values in a patch which alters a patch.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Fixes: cf65262492 ("kernel: bump 4.19 to 4.19.51")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Altered patches:
- 370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch
- 220-optimize_inlining.patch
- 640-netfilter-nf_flow_table-add-hardware-offload-support.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Refreshed all patches.
Altered patches:
- 220-optimize_inlining.patch
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
urandom-seed content was split from base-files into separate package so
in order to preserve the current functionality and to provide some
fallback mechanism in case jent-rng initialization fails in urngd we
need to add it back.
urngd is OpenWrt's micro non-physical true random number generator based
on timing jitter.
Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Only the repo should not use https. Otherwise the build would need
a wget/uclient_fetch with tls support.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
e26ffb31df fixed only embedded modules
symbol collection. If we are building external modules, like broadcom-wl
or lantiq dsl stuff then modules which do EXPORT_SYMBOL have unresolved
paths in Module.symvers and external module which depend on other
external modules will have empty dependencies, leading to broken
module loading.
This was discussed on IRC with Jonas some time ago.
Fix this by handling both resolved and unresolved paths.
Fixes: e26ffb31df ("build: fix module symbol collection if build_dir is a symlink")
Signed-off-by: Roman Yeryomin <roman@advem.lv>
[jonas.gorski@gmail.com: add appropriate fixes tag]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Adds support to && operand in DEPENDS. Also, fixes generation of ||
dependencies by scripts/package-metadata.pl.
The precedence order from higher to lower is && then ||. Use of
parentheses to change the order is not supported. As before, they are
silently ignored. Use them for readability only.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [DMARC removal]
The helper shared Build/append-uboot in include/image-commands.mk
uses it, so include this variable in DEFAULT_DEVICE_VARS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds a new variable DISABLED_SERVICES to ImageBuilder Makefile, which
defines a list of services (installed as /etc/init.d/*) to be disabled
during the build of a custom image (normally all are enabled).
It comes handy when a particular service should not be run under normal
circumstances, but should be ready in the image for situations when it
might be needed.
Signed-off-by: Richard Musil <risa2000x@gmail.com>
If the target supports a newer kernel version that is not used by default
yet, it can be enabled with this option
Signed-off-by: Felix Fietkau <nbd@nbd.name>
No target is using kernel 3.18 anymore, remove all the generic
support for kernel 3.18.
The removed packages are depending on kernel 3.18 only and are not used on
any recent kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed all patches.
New symbols:
- CONFIG_LDISC_AUTOLOAD
- CONFIG_PPC_BARRIER_NOSPEC
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This patch doesn't seem to have any more users.
The only one used to be target in
`target/linux/etrax/image/e100boot/Makefile`.
That target has since been removed via commit
1080f68b2b .
There doesn't seem to be any reason left for this workaround.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Otherwise tar will keep the sgid bit when running
from a sgid-set directory, resulting in a different
file being generated.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message, removed DMARC]
It was reported to me on IRC today, that my change causes issues with
kernel versions between 4.14 and 4.19.
It's because I've wrongly used `git describe` in order to get kernel
version where we should disable noisy DTC checks, but I should've used
`git tag --contains` instead.
Fixes: cbbef976e2 ("build: dtc: Disable noisy warnings by default")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Set the toolchain's ARM CPU and FPU architectures by utilizing' gcc's
--with-cpu / --with-fpu configure options that: "Specify which cpu
variant the compiler should generate code for by default. cpu will
be used as the default value of the -mcpu= switch."
This will resolve the following kernel compilation failures under
gcc 8.x on ARM because the kernel wants to set (possibly conflicting)
optimization flags.
.../ccyVnmrs.s:204: Error: selected processor does not support `dmb ish' in ARM mode
.../ccyVnmrs.s:215: Error: architectural extension `mp' is not allowed for the current base architecture
.../ccyVnmrs.s:216: Error: selected processor does not support `pldw [r4]' in ARM mode
Because this is a big change, the .config and toolchain need to be
refreshed (as in removed and regenerated).
Reported-by: Ansuel Smith <ansuelsmth@gmail.com>
Reported-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [#1203]
Signed-off-by: Boris Krasnovskiy <borkra@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [extended commit message,
removed now-deprecated CPU_CFLAGS, changed author to gmail address]
If no feed.conf or feeds.conf.default is found on image generation with
the imagebuilder we always get the following message "Unable to open
feeds configuration at <dir>/scripts/feeds line 48." on std error.
To get rid off this needless warning on image generation with the
imagebuilder supress the output in feeds.mk.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Having image metadata (and signature) appended is a condition for
semi-automated sysupgrade, hence IB needs to be able to tell which
images will end up with metadata.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
allow downstream projects to see the current version of the metadata,
usefull if eventually more variables change
Signed-off-by: Paul Spooren <mail@aparcar.org>
currently the "board" parameter contains $(BOARD) which actually results
to `<target>` (like ramips, ar71xx) without subtarget. However, one
actually excepts (not?) to contain BOARD_NAME or DEVICE_NAME.
Signed-off-by: Paul Spooren <mail@aparcar.org>
When autoloading more than one modules per packages,
/etc/modules.d/$module depends on the file system ordering.
To test this: use disorderfs on the build_dir and build kmod-sched.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
Use 'dtc' from kernel sources instead of relying on host tool.
Fixes: bf4630e5ad ("build: add helpers for generating QSDK sysupgrade compatible images")
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Qualcomm SDK (QSDK) sysupgrade compatible images for IPQ40xx, IPQ806x
and IPQ807x use FIT format together with 'dumpimage' tool from U-Boot
for verifying and extracting them. Based on 'images' sections names,
corresponding mtd partitions are flashed. For example, in case of
NOR-only boards, below mapping is used (section name -> mtd name):
hlos* -> 0:HLOS
rootfs* -> rootfs
And for boards with NAND (kernel inside UBI):
ubi* -> rootfs
Above mappings come from unmodified QSDK sources and might be wrong for
boards running custom or modified QSDK-based firmware. Some of vendors
adjust them to meet their modified mtd layout or features like recovery
or dual-image support.
This adds simple script 'mkits-qsdk-ipq-image.sh' (based on 'mkits.sh')
for generating FIT images tree source files, compatible with the QSDK
sysupgrade format. Resulting images can be used for initial (factory ->
OpenWrt) installation and would work both in CLI and GUI.
The script is universal in a way it allows to include as many sections
as needed. To make use of it, two generic/basic build recipes for NOR
and NAND based boards are also included in 'image-commands.mk':
Build/qsdk-ipq-factory-nand
Build/qsdk-ipq-factory-nor
Example usage for board with UBI in NAND:
IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The original patch removed the printing completely, just remove the
color.
Fixes: eabc1ddc45 ("build: Honour NO_COLOR in include/scan.mk")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
BIN_DIR can be set to overwrite the output path for new images. This is an
advertised feature for the imagebuilder and is used by systems like
LibreMesh's chef.
The legacy images are build using a new sub-make which doesn't receive the
variable overwrites of the parent make process. As result, the BIN_DIR is
automatically defined to the default value from rules.mk. The images will
therefore not be placed in the output path which was selected by the user.
Providing BIN_DIR as an explicit variable override to the sub-make works
around this problem.
Fixes: 26c771452c ("image.mk: add LegacyDevice wrapper to allow legacy image building code to be used for device profiles")
Reported-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Hi all:
This is my first OpenWrt patch. I am a clean, pure newbie! 8-)
Honour NO_COLOR in Makefile function 'progress' in include/scan.mk, in the same way that include/verbose.mk does.
Signed-off-by: R. Diez <rdiezmail-openwrt@yahoo.com>
The KERNEL_ENTRY was missing from the DEFAULT_DEVICE_VARS.
This bug was discovered while preparing alternative images
for the mpc85xx's TP-Link WDR4900-V1, which all failed to
boot due to this:
|## Booting kernel from Legacy Image at 02000000 ...
| Image Name: POWERPC OpenWrt Linux-4.14.96
| Image Type: PowerPC Linux Kernel Image (uncompressed)
| Data Size: 2056568 Bytes = 2 MiB
| Load Address: 01000000
| Entry Point: 00000000
| Verifying Checksum ... OK
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It was reported to me today on IRC, that building of artifacts doesn't
work properly if the concat_cmd references DEVICE_NAME variable. I've
found out, that it's due to missing call of Device/Export in artifacts
building code path, so this patch adds the missing Device/Export call
which in turn exports DEFAULT_DEVICE_VARS into the artifacts
environment.
Fixes: 493c9a3551 ("build: Introduce building of artifacts")
Tested-by: Oskari Lemmela <oskari@lemmela.net>
Reported-by: Oskari Lemmela <oskari@lemmela.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use LINUX_DIR as a path when patching kernel. Doesn't break the current usage,
but allows to create packages that will contain variation of a kernel with
kernel being build in some subdirectory of PKG_BUILD_DIR.
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
This fixes two issues with cleaning package files from STAGING_DIR:
* CleanStaging currently can only remove files and not directories. This
changes CleanStaging to use clean-package.sh, which does remove
directories.
* Because of the way directories are ordered in the staging files list,
clean-package.sh currently tries (and fails) to remove parent
directories before removing subdirectories. This changes
clean-package.sh to process the staging files list in reverse, so that
subdirectories are removed first.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
While helping with review and build testing of a few 4.19 pull requests,
I've noticed, that dtc compiler in OpenWrt uses different options then
upstream kernel, which is leading to a very noisy output[1]. It wouldn't
be that bad per se, but a lot of such warnings aren't easily fixable so
I think, that we should follow what upstream does and simply ignore^W
silence those noisy warnings.
So this patch tries to syncs dtc compiler flags with upstream kernel
till version 4.19.13, disabling those warnings as they were added in
upstream kernel:
v4.6-rc1-2-gbc55398 dtc: turn off dtc unit address warnings by default
The newly added dtc warning to check DT unit-address without reg
property and vice-versa generates lots of warnings. Turn off the check
unless building with W=1 or W=2.
v4.11-rc2-11-g8654cb8 dtc: update warning settings for new bus and node/property
dtc gained new warnings checking PCI and simple buses, unit address
formatting, and stricter node and property name checking. Disable the
new dtc warnings by default as there are 1000s. As before, warnings are
enabled with W=1 or W=2. The strict node and property name checks are a
bit subjective, so they are only enabled for W=2.
v4.16-rc3-9-g4fd98e3 scripts: turn off some new dtc warnings by default
The latest dtc update adds some new noisy warnings, so turn them off by
default. Disable 'avoid_unnecessary_addr_size' and 'alias_paths'. They
can be re-enabled by building with 'W=1'.
v4.17-rc1-27-g74656b6 kbuild: disable new dtc graph and unit-address warnings
dtc gained some new warnings for OF graphs and unique unit addresses,
but they are currently much too noisy. So turn off
'graph_child_address', 'graph_port', and 'unique_unit_address' warnings
by default. They can be enabled by building dtbs with W=1.
Build tested on imx6 and ath79 with 4.14 and 4.19.
1. https://github.com/openwrt/openwrt/pull/1694#issuecomment-450864335
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch fixes following error with U-Boot 2019.01 on imx6:
In file included from tools/lib/crc16.c:1:0:
./tools/../lib/crc16.c: In function 'crc16_ccitt':
./tools/../lib/crc16.c:70:2: error: 'for' loop initial declarations are only allowed in C99 mode
for (int i = 0; i < len; i++)
^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code
Code was introduced in the upstream v2019.01-rc1-154-g51c2345:
commit 51c2345bd24837f9f67f16268da6dc71573f1325
Author: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Date: Sun Nov 25 19:22:19 2018 +0100
Roll CRC16-CCITT into the hash infrastructure
Upstream has added -std=gnu11 host flag in v2018.07-rc2-1-gfa89399:
commit fa893990e9b53425af5f5059e04a2bffde91ccf9
Author: Tom Rini <trini@konsulko.com>
Date: Tue Jun 19 23:53:54 2018 -0400
Makefile: Ensure we build with -std=gnu11
Build tested on imx6: apalis, mx6sabresd, nitrogen6dl, nitrogen6dl2g,
nitrogen6q, nitrogen6q2g, nitrogen6s, nitrogen6s1g,
wandboard
Run tested: apalis (pending PR #1595)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds the 'Build/linksys-image' rule and the
'linksys-image.sh' script to the build system.
This change is needed for generating factory images for the Linksys
EA6350v3 device. Without this patch, only valid sysupgrade images can be
generated. With this patch, users can flash the device without the
need of physical access or disassembly.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
This adds the hardening options also to the toolchain build.
With this change the /usr/lib/libstdc++.so.6.0.24 library will have
stack canaries and the /lib/libgcc_s.so.1 library will have Full RELRO.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Filter out potential duplicates with the package name
(e.g. when renaming libfoo1 w/ ABI_VERSION:=1 to libfoo)
- Use the GetABISuffix macro to properly separate the suffix
with a dash in case the basename ends with a number
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When a library package specifies additional provides, e.g. libncurses
which provides libncursesw, we should also append the abi version
suffix to each provide, since there may be more than one package
providing the virtual library.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This may be useful if you don't entirely trust your flash and want to be able
to check for corruptions.
Signed-off-by: Michal Hrusecky <Michal@Hrusecky.net>
Add the ABI_VERSION source makefile variable to the binary package basename
and resolve source dependencies on packages with ABI_VERSION set to such
expanded names.
If for example a package specifies DEPENDS:=libopenssl while the OpenSSL
Makefile specifies ABI_VERSION:=1.0.0, the resulting ipk control data
dependency will be "Depends: libopenssl1.0.0" and the libopenssl ipk file
will be called "libopenssl1.0.0_<version>_<arch>.ipk".
The next time a library such as OpenSSL is updated to an incompatible
version, the ABI_VERSION shall be changed accordingly to prevent opkg from
simply upgrading to an incompatible library without considering the
dependencies of already installed packages.
Also introduce another "SourceName" control field which is required by
the newly introduced "scritps/ipkg-remove" to determine the proper related
.ipk files to delete upon buildroot package clean operations.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Subdequent commits need this information to resolve the ABI version when
computing binary ipk dependencies.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Subsequent commits will put more auxiliary information into this file,
such as the per-package ABI version, so rename the metadata script
subcommand and file names accordingly.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
I moved xor-image into image-commands.mk to use it in ath79 target.
It required for NEC WG800HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Refresh all patches
Remove upstream patch:
backport-4.14/424-v4.20-net-dsa-fix-88e6060-roaming.patch
Minor tweak to generic/hack-4.14/902-debloat_proc.patch to cleanly apply
after upstream changes.
Tested-on: ath79
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
We need to use resolved file list as prerequisites for repacking kmod
.ipk files. Note that currently version_filter uses a Makefile macro
KERNEL_PATCHVER that should be available at ipk building time.
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This commit ports both dir-825-c1 and dir-835-a1 from ar71xx to ath79.
They're pretty much identical, except dir-835-a1 has less LEDs.
The routers come with 128 MByte of RAM and 16 MBytes of flash and sport
2.4GHz and 5.0GHz wireless. Both routers have entries already in
OpenWrt's TOH. Please check there for more information on these
antiquities.
https://openwrt.org/toh/hwdata/d-link/d-link_dir-825_c1https://openwrt.org/toh/hwdata/d-link/d-link_dir-835_a1
Installation:
1. Connect to the web interface of the vendor firmware (usually
listening on 192.168.0.1).
2. Go to "Tools", then "Firmware".
3. In the "Firmware Upgrade" box click "Browse".
4. Select the OpenWrt factory image for your router.
5. Click "Upload", confirm the popups if you agree to flash the file you
selected.
6. Wait for firmware upgrade to complete. It takes about 5 minutes.
Run-tested on dir-825-c1. dir-835-a1 should work as well, but I don't
have this router so I can't confirm.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [trivial changes]
This command enables factory image generation for Cameo boards. On
upgrade the vendor firmware will check the size of the provided image
and if a specific string is located at the end of the binary.
cameo-factory will generate an image that the vendor firmware accepts.
Tested on a D-Link DIR-825 C1 with vendor firmwares 3.01 and 3.04.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
In mainline kernel commit 02c7b25e5f5 ("netfilter: nf_tables: build-in
filter chain type") all chain filters were merged into one file and into
one kernel module to save some memory. The code protected by these
configuration options CONFIG_NF_TABLES_BRIDGE, CONFIG_NF_TABLES_IPV4,
CONFIG_NF_TABLES_ARP, CONFIG_NF_TABLES_IPV6, CONFIG_NF_TABLES_NETDEV and
CONFIG_NF_TABLES_INET was merged into the nft_chain_filter.c file which
is now always compiled into the nf_tables.ko file.
This only happened in kernel 4.19 and OpenWrt has to select these as
modules in older kennel versions. Mark them as build-in in the kernel
4.19 specific kernel configuration file which will then not be
overwritten by the package specific settings which try to make them
modular again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit 0168e8b361 ("netfilter: nat: merge ipv4/ipv6 masquerade
code into main nat module") the CONFIG_NF_NAT_MASQUERADE_IPV4 and
CONFIG_NF_NAT_MASQUERADE_IPV6 kernel configuration option were changed
to bool and the code will not be compiled as a own module any more, but
it will be integrated into nf_nat_ipv4.ko or nf_nat_ipv6.ko to save some
memory.
Activate these options as bool in the generic kernel 4.19 configuration
only, to always build them into the nf_nat_ipv*.ko modules. The kmod
file will still try to select them as module, but the generic
configuration will not be overwritten.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some kernel modules from kmod-ipt-conntrack-extra depend on
nf_conncount.ko, which was added in kernel 4.16, add it to the kmod.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nf_socket.ko module was split in commit 8db4c5be88f ("netfilter:
move socket lookup infrastructure to nf_socket_ipv{4,6}.c") into a
common, n IPv4 and an IPv6 part.
The nf_tproxy.ko module was split in commit 45ca4e0cf27 ("netfilter:
Libify xt_TPROXY") into a common, an IPv4 and an IPv6 part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit a0ae2562c6c ("netfilter: conntrack: remove l3proto
abstraction") The modules nf_conntrack_ipv4.ko, nf_conntrack_ipv6.ko and
nf_conntrack.ko were squashed together into one module. This module now
depends on nf_defrag_ipv6 when IPv6 support was activated. This is part
of the main netfilter packages, so add nf_defrag_ipv6.ko also to the
default netfilter packages on kernel 4.19 and later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.
The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.
The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch
Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch
Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.
The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch
This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
They are no longer stored in the "testing" subdirectory and are not
available as .tar.xz archives. If -rc is detected download it from the
git.kernel.org and use .tar.gz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Currently every file in boot directory is copied over target /boot on
root file system and is usually inaccessible because appropriate boot
file system is mounted on top of it. Therefore remove /boot, which in
result will also save space on target root file system.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
We currently could (ab)use IMAGES for this task, but the downside is,
that the filenames has filesystem tied to the filename, which might be
confusing as the artifact itself don't has to be used with that specific
filesystem. Another downside is, that the artifacts built with IMAGES
target are build for every FILESYSTEMS filesystem.
Consider following use case:
define Device/apalis
...
FILESYSTEMS := ext4 squashfs
IMAGES := spl-uboot.bin recovery.scr
IMAGE/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
IMAGE/recovery.scr := recovery-scr
endef
Where we would get target binaries with following filenames:
openwrt-imx6-apalis-squashfs.recovery.scr
openwrt-imx6-apalis-squashfs.spl-uboot.bin
openwrt-imx6-apalis-ext4.recovery.scr
openwrt-imx6-apalis-ext4.spl-uboot.bin
With proposed patch, we could now just do:
define Device/apalis
...
ARTIFACTS := spl-uboot.bin recovery.scr
ARTIFACT/spl-uboot.bin := append-uboot-spl | pad-to 68k | append-uboot
ARTIFACT/recovery.scr := recovery-scr
endef
Which would produce target binaries with following filenames:
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-spl-uboot.bin
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The -rcX "testing" kernels are no longer hosted on
cdn.kernel.org file servers directly in a "testing"
directory. Therefore the logic that tested for "-rc"
can be removed.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add a basic variant which provides WPA-PSK only, 802.11r and 802.11w and
is intended to support 11r & 11w (subject to driver support) out of the
box.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The tl-wa850re-v2 images from the ar71xx/tiny target are getting too big
with the default packages. The size check is done before the meta data
is added so there is no file to add meta data to or to sign. Originally
errors in Build/append-metadata were getting ignored, but if the signing
fails the error is not ignored.
This adds a check if the file to be signed is there and only does the
signing if it is there. This way it does not fail if the package
creation was already aborted earlier.
Fixes: 848b455d2e ("image: use ucert to append signature")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
